LG | BH200 | LG BH200 Owner’s Manual

BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 1
Super Blu Player
Owner’s Manual
Model: BH200
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, should be placed on the apparatus.
CAUTION concerning the Power Cord
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the
user to the presence of uninsulated dangerous
voltage within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a confined
space such as a book case or similar unit.
CAUTION:
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to
protect it from over heating.
The openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.This
product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instruction have been adhered to.
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future reference.
Should the unit require maintenance, contact an authorized
service center.
Use of any controls, adjustments, or procedures other than
those specified herein may result in hazardous radiation
exposure.
To prevent direct exposure to laser beam, do not try to
open the enclosure. Visible laser radiation when open. DO
NOT STARE INTO BEAM.
2
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits.
Check the specification page of this owner’s manual to be
certain.
Do not overload wall outlets. Overloaded wall outlets, loose
or damaged wall outlets, extension cords, frayed power
cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock
or fire. Periodically examine the cord of your appliance,
and if its appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and have the
cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse,
such as being twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains
cord plug. When installing the product, ensure that the plug
is easily accessible.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 3
Contents
Installation and Setup . . . . . . . . . . . . . . . .13-24
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . .13
HDMI connection . . . . . . . . . . . . . . . . . . . .14
Connections to Your TV . . . . . . . . . . . . . . . .15
Connecting to an Amplifier . . . . . . . . . . . . . .16
Internet connection . . . . . . . . . . . . . . . . . . .17
Resolution Setting . . . . . . . . . . . . . . . . . . . .18
Initial Settings . . . . . . . . . . . . . . . . . . . . . . .19
- General Operation . . . . . . . . . . . . . . . .19
- [DISPLAY] Menu . . . . . . . . . . . . . . .19-20
- [LANGUAGE] Menu . . . . . . . . . . . . . .20
- [AUDIO] Menu . . . . . . . . . . . . . . . . . .21
- [LOCK] Menu (Parental Control) . . . . . .22
- [NETWORK] Menu . . . . . . . . . . . . . . . .23
- [OTHERS] Menu . . . . . . . . . . . . . . . . .24
Operations . . . . . . . . . . . . . . . . . . . . . . . . .25-30
General playback features . . . . . . . . . . .25-26
If a disc menu screen is displayed . . . . . . . .27
Time Search . . . . . . . . . . . . . . . . . . . . . . . .27
Marker Search . . . . . . . . . . . . . . . . . . . . . . .27
Screen Saver . . . . . . . . . . . . . . . . . . . . . . .27
Using Color (A, B, C, D) Buttons . . . . . . . . .27
Displaying Disc Information On-Screen . . . .27
Hybrid Discs . . . . . . . . . . . . . . . . . . . . . . . .28
Last Scene Memory . . . . . . . . . . . . . . . . . . .28
Using the cursor function . . . . . . . . . . . . . . .28
Internet connection feature . . . . . . . . . . . . .28
Playing an Audio CD or MP3/WMA files . . . .29
MUSIC menu options . . . . . . . . . . . . . . . . .29
Viewing a JPEG file . . . . . . . . . . . . . . . . . . .30
Introduction
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .5-12
About the
Symbol Display . . . . . . . . . . . . .5
Symbols Used in this Manual . . . . . . . . . . . . .5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . .5
Moisture Condensation . . . . . . . . . . . . . . . . .5
Handling the Unit . . . . . . . . . . . . . . . . . . . . . .5
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . .6
Regional Code . . . . . . . . . . . . . . . . . . . . . . .6
BD-ROM Disc Features . . . . . . . . . . . . . . . . .7
HD DVD Disc Features . . . . . . . . . . . . . . . . .8
Compatibility Notes . . . . . . . . . . . . . . . . . . . .8
Certain System Requirements . . . . . . . . . . . .8
Important Notice for TV colour system . . . . . .8
Using an USB Flash Drive . . . . . . . . . . . . . . .9
Using the Home Menu . . . . . . . . . . . . . . . . . .9
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . .10
Display Window . . . . . . . . . . . . . . . . . . . . . .11
Remote Control . . . . . . . . . . . . . . . . . . . . . .12
Remote Control Operation . . . . . . . . . . . . . .12
Reference . . . . . . . . . . . . . . . . . . . . . . . . . .31-38
Controlling a TV with the Supplied
Universal Remote Control . . . . . . . . . . . . . . . .31
To program the remote to control the TV
using the manufacturer code . . . . . . . . . . . .31
Code numbers of controllable TVs . . . . .32-33
Language Codes . . . . . . . . . . . . . . . . . . . . .34
Area Codes . . . . . . . . . . . . . . . . . . . . . . . . .34
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .35
Customer Support . . . . . . . . . . . . . . . . . . . .35
Specifications . . . . . . . . . . . . . . . . . . . . . . .36
This unit’s Audio Output Specifications . . . . .37
Open source software notice . . . . . . . . . . . .38
3
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 4
Notes on Copyrights
4
Because AACS (Advanced Access Content
System) is approved as content protection system for BD and HD DVD format, similar to use of
CSS (Content Scramble System) for DVD format,
certain restrictions are imposed on playback, analog signal output, etc., of AACS protected contents. The operation of this product and restrictions on this product may vary depending on your
time of purchase as those restrictions may be
adopted and/or changed by AACS after the production of this product.
Furthermore, BD-ROM Mark and BD+ are additionally used as content protection systems for
BD format, which imposes certain restrictions
including playback restrictions for BD-ROM Mark
and/or BD+ protected contents. To obtain additional information on AACS, BD-ROM Mark, BD+,
or this product, please contact an authorized
Customer Service Center.
Many HD DVD/BD-ROM/DVD discs are encoded
with copy protection. Because of this, you should
only connect your player directly to your TV, not
to a VCR. Connecting to a VCR results in a distorted picture from copy-protected discs.
This product incorporates copyright protection
technologies that are protected by certain U.S.
patents and other intellectual property rights
owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation and is intended for home and other
limited viewing uses only, unless otherwise
authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, HD DVDs, BD-ROM discs,
DVDs, CDs and other materials may subject you
to civil and/or criminal liability.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Surround
are registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-2007
DTS, Inc. All Rights Reserved.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
Qdeo, QuietVideo and the Qdeo trademarks are
registered trademarks of Marvell or its affiliates.
What is SIMPLINK?
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s
with SIMPLINK are connected through HDMI connection.
• Controllable functions by LG TV’s remote control;
Play, Pause, Scan, Skip, Stop, Power Off, etc.
• Refer to the TV owner’s manual for the details of
SIMPLINK function.
• LG TV’s with SIMPLINK function have the logo as
shown above.
Note:
Depending on the disc type or playing status, some
SIMPLINK operation may differ from your purpose
or not work.
5/2/08
11:05 AM
Page 5
Introduction
To ensure proper use of this product, please read
this owner’s manual carefully and retain for future
reference.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
Introduction
BH200-P-ASGPLLK-ENG
This manual provides information on the operation
and maintenance of your player. Should the unit
require service, contact an authorized service location.
About the
Symbol Display
“
” may appear on your TV display during operation and indicates that the function explained in this
owner’s manual is not available on that specific
media.
Symbols Used in this Manual
Note:
Indicates special notes and operating features.
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols are applicable only to the disc represented by
the symbol.
BD BD-ROM disc
HD DVD HD DVD-Video disc
DVD DVD-Video disc
ACD Audio CDs
MP3 MP3 files
WMA WMA files
JPEG JPEG files
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the
disc by the edges so that fingerprints do not get on
the surface. Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or
anti-static spray intended for older vinyl records.
Moisture Condensation
Never operate this product immediately after moving
it from a cold location to a warm location. Leave it
for two or three hours without operating it. If you use
this product in such a situation, it may damage discs
and internal parts.
Handling the Unit
When shipping the unit
Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally
packed at the factory.
Keeping the exterior surfaces clean
Use the supplied cloth for cleaning the surfaces of
the player.
•
Do not use volatile liquids such as insecticide
spray near the unit.
•
Wiping with strong pressure may damage the
surface.
•
Do not leave rubber or plastic products in contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution.
Do not use strong solvents such as alcohol, benzine,
or thinner, as these might damage the surface of the
unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or
worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
5
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 6
Playable Discs
Regional Code
Blu-ray Disc
Discs such as movies that can be purchased or rented
This unit has a regional code printed on the rear of
the unit. This unit can play only BD-ROM, HD DVD,
or DVD discs labeled same as the rear of the unit or
“ALL”.
HD DVD Disc
Discs such as movies that can be purchased or rented
Notes:
Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD±R/RW) disc
itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.
Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
Do not use irregularly shaped discs (e.g., heartshaped or octagonal). Doing so may result in
malfunctions.
Depending on the recording software & the finalization, some recorded discs (CD-R/RW or
DVD±R/RW) may not be playable.
DVD±R/RW and CD-R/RW discs recorded using
a personal computer or a DVD or CD Recorder
may not play if the disc is damaged or dirty, or if
there is dirt or condensation on the player’s lens.
If you record a disc using a personal computer,
even if it is recorded in a compatible format, there
are cases in which it may not play because of the
settings of the application software used to create
the disc. (Check with the software publisher for
more detailed information.)
This player requires discs and recordings to meet
certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are
automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files)
and these require certain pre-existing conditions
to ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has no
right to grant such permission. Permission should
always be sought from the copyright owner.
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be purchased or rented
DVD-R (8 cm / 12 cm disc)
Video mode and finalized only
Supports the dual layer disc also
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only
DVD-RAM (8 cm / 12 cm disc)
Standard version 2.0 only
DVD+R
Finalized disc only
Supports the dual layer disc also
DVD+RW
Video mode and finalized only
Audio CD (8 cm / 12 cm disc)
Music CDs or CD-Rs/CD-RWs in music
CD format that can be purchased
CD-R/CD-RW (8 cm / 12 cm disc)
CD-R/CD-RW discs that contain audio
titles, MP3, WMA, or JPEG files.
6
5/2/08
11:05 AM
Page 7
BD-ROM Disc Features
BD-ROM Discs can store 25 GB (single layer) or
50 GB (dual layer) on a single sided disc - about
5 to 10 times the capacity of a DVD.
BD-ROM Discs also support the highest quality HD
video available in the industry (up to 1920 x 1080) Large capacity means no compromise on video
quality. Furthermore, a BD-ROM disc has the same
familiar size and look as DVD.
• The following BD-ROM disc features are disc
dependent and will vary.
• Appearance and navigation of features will also
vary from disc to disc.
• Not all discs will have the features described
below.
• BD-ROM Hybrid disc has both BD-ROM and DVD
(or CD) layers on one side. Because this type of
disc is a technology currently in development,
such discs may not operate properly in this player.
Video highlights
The BD-ROM format for movie distribution supports
three highly advanced video codecs, including
MPEG-2, MPEG4 AVC (H.264), and SMPTE VC1.
HD video resolutions are also available:
• 1920 x 1080 HD
• 1280 x 720 HD
For High-Definition Playback
To view high-definition contents from BD-ROM discs,
an HDTV is required. Some discs may require HDMI
OUT for viewing of high-definition contents. Ability to
view high-definition contents in BD-ROM discs may
be limited depending on the resolution of your TV.
Graphic planes
Two individual, full HD resolution (1920x1080)
graphic planes (layers) are available, on top of the
HD video layer. One plane is assigned to videorelated, frame accurate graphics (like subtitles), and
the other plane is assigned to interactive graphic
elements, such as buttons or menus.
For both planes, various wipes, fades and scroll
effects may be available.
Menu sounds
When you highlight or select a menu option, sounds
can be heard such as button clicks or a voice-over
explaining the highlighted menu choice.
Introduction
BH200-P-ASGPLLK-ENG
Multi-page/PopUp Menus
With DVD-Video, playback is interrupted each time a
new menu screen is accessed. Due to BD-ROM
disc’s ability to preload data from the disc without
interrupting playback, a menu can consist of several
pages.
You can browse through the menu pages or select
different menu paths, while the audio and video
remain playing in the background.
Interactivity
Certain BD-ROM Discs may contain animated
menus and/or trivia games.
User Browsable Slideshows
With BD-ROM Discs, you can browse through various still pictures while the audio remains playing.
Subtitles
Depending on what is contained on the BD-ROM
disc, you may be able to select different font styles,
sizes and colors for some subtitles, Subtitles may
also be animated, scrolled or faded in and out.
BD-J Interactive Capability
The BD-ROM format supports Java for interactive
functions. “BD-J” offers content providers almost
unlimited functionality when creating interactive
BD-ROM titles.
BD-ROM Disc Compatibility
This player supports BD-ROM Profile 1 version 1.0
only. Other profiles (i.e., BD-ROM Profile 1 version
1.1 or Profile 2) could be supported through
updating player’s firmware later. It may be required
to update the firmware in case of playing a certain
newly released commercial BD-ROM disc.
For updating player’s firmware, please refer to
http://sg.lgservice.com or contact LG Electronics
customer care center.
Graphic
Plane
HD Video
7
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 8
HD DVD Disc Features
Certain System Requirements
HD DVD video discs are high-density, high-capacity
discs.
For high definition video playback:
There are 2 types of HD DVD disc; one is standard content disc and the other is advanced content disc. Standard content disc is pure extension
of DVD Video. Advanced content disc realizes
more interactivity in addition to the extension of
audio and video realized by standard disc.
High definition display that has COMPONENT or
HDMI input jacks.
BD-ROM or HD DVD disc with high definition
content.
HDMI or HDCP capable DVI input on your display
device is required for some content (as specified
by disc authors).
For up-conversion of standard definition DVD, an
HDMI or HDCP capable DVI input on your display
device is required for copy protected content.
The HD DVD disc standard has been approved
by the DVD forum.
HD DVD (single layer): Maximum capacity of 15 GB
HD DVD (dual layer): Maximum capacity of 30 GB
A single layer single sided disc (15 GB) has
capacity of about maximum 8 hours in 1125 line
high definition picture; about maximum 48 hours
in 525 line standard definition picture (depending
on bitrate of pre-recorded contents).
For Dolby® Digital Plus and DTS-HD multi-channel
audio playback:
HD DVD Twin Format Discs have both HD DVD
and DVD layers on one side. HD DVD
Combination DVD Discs have HD DVD material
on one side and standard DVD material on the
other side. Because this type of disc is a technology currently in development, such discs may not
operate properly in this player.
Some titles may be played back with black “letterbox bars” because the title is recorded with bars
by the contents provider.
Compatibility Notes
8
Because BD-ROM and HD DVD are a new format, certain disc, digital connection and other
compatibility issues are possible. If you experience compatibility problems, please contact an
authorized Customer Service Center.
Viewing high-definition content and up-converting
standard DVD content may require an HDMIcapable input or HDCP-capable DVI input on
your display device.
Some BD-ROM, HD DVD and DVD discs may
restrict the use of some operation commands or
features.
Dolby TrueHD, Dolby Digital Plus and DTS-HD
capability is limited to 5.1 channels if you use
Digital Audio or HDMI connection for the audio
output of the unit.
This player includes memory that is used to store
some disc related information, including downloaded on-line content. The disc you are using
will control how long this information is retained.
An amplifier/receiver with a built-in (Dolby Digital
or DTS) decoder.
Main, center, surround speakers and subwoofer
as necessary for chosen format.
Important Notice for TV colour
system
The colour system of this player differs according to
currently playing discs.
For example, when the player plays back the disc
recorded in the NTSC colour system, the image is
outputted as a NTSC signal.
Only the multi system colour TV can receive all
signals outputted from the player.
Notes:
If you have a PAL colour system TV, you will see
just distorted images when using discs recorded in
NTSC.
The multi system colour TV changes the colour
system automatically according to input signals. In
case that the colour system is not changed
automatically, turn it off and then on to see normal
images on screen.
If you try to record a NTSC output signal from the
player with your recorder, the recorder may not
record the signal correctly.
5/2/08
11:05 AM
Page 9
Using an USB Flash Drive
Using the Home Menu
This unit can play the MP3 / WMA / JPEG files contained in the USB Flash Drive.
From the Home Menu screen you can access all the
Media for playback and setting of the unit.
Inserting/Removing the USB Flash
Drive
Introduction
BH200-P-ASGPLLK-ENG
1. Press HOME and the Home Menu appears.
2. Use b / B to select the desired option then
press ENTER.
[Movie] – Start video media’s playback.
[Photo] – Displays PHOTO menu.
[Music] – Displays MUSIC menu.
[Setup] – Displays Setup menu.
Inserting the USB Flash Drive
Insert straight-in until it fits into place.
Tip:
Removing the USB Flash Drive
Withdraw the USB Flash Drive carefully.
If you select the [Photo] or [Music] option when the
USB Flash Drive is connected and a disc is inserted
simultaneously, the menu for selecting a media will
appear. Select a media then press ENTER.
Notes:
For example:
This unit supports only USB Flash Drives with
FAT16 or FAT32 format.
Do not extract the USB Flash Drives during operation (play, etc.).
A USB Flash Drive which requires additional program installation when you have connected it to a
computer, is not supported.
USB Flash Drive: USB Flash Drive that support
USB1.1 and USB2.0.
Using the USB Flash Drive
Notes:
• The unit will be in complete stop mode then
HOME menu will appear if you press HOME during playback.
• If you insert a DVD or an unplayable disc that is
formatted as ISO9660 or UDF, the [Photo] or
[Music] option can be selected in the HOME
menu. But you cannot play it
1. Connect a USB Flash Drive.
2. Press HOME on the Remote Control.
3. Select [Music] or [Photo] option then press
ENTER.
4. Select [USB] then press ENTER.
MUSIC (or PHOTO) menu will appear.
Details for the menu are on page 29-30.
9
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 10
Front Panel
a
b
c
d
g
a POWER Button
Switches the unit ON or OFF.
b Disc Tray
Insert a disc here.
c Blu-ray Disc Indicator
Indicates when a BD-ROM disc is loaded.
d HD DVD Indicator
Indicates when an HD DVD disc is loaded.
e Display Window
Shows the current status of the player.
f Remote Sensor
Point the Remote Control here.
g Z (OPEN/CLOSE)
Opens or closes the disc tray.
h N / X (PLAY / PAUSE)
Starts playback.
Pause playback temporarily, press again to exit
pause mode.
i x (STOP)
Stops playback.
j . / > (SKIP)
Go to next or previous track/chapter.
k USB Port
Connect a USB Flash Drive.
10
h
e
f
i
j k
Tip:
Z, N / X , x, . and > buttons are operated
with a slight/brief touch.
Precautions in using the touch buttons
Use the touch buttons with clean and dry hands.
Do not press the touch buttons with too much
force.
Do not touch the button with any conductive
material such as metallic object (Disc, etc). It may
cause a malfunction.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 11
a
b c d
HDMI
YPbPr 1080
720
576
BD HD DVD CD I P
e
f
h
i
j
k l
TITLE
TRK CHAP RPT
A-B
RDM
AGL
m
g
n
a HDMI Indicator
Indicates when the HDMI output is available.
h Repeat Mode Indicator
Indicates when playing in repeat mode.
b YPbPr Indicator
Indicates when the component video output is
available.
i A-B Repeat Mode Indicator
Indicates when playing in A-B repeat mode.
c Status Indicator
N: Playing
X: Paused
d Video Output Resolution Indicator
Displays the video output resolution currently
selected.
576i: 576 interlace
576p: 576 progressive
720p: 720 progressive
1080i: 1080 interlace
1080p: 1080 progressive
e TITLE
Indicates current title number.
f TRK (Track) Indicator
Indicates current track number.
g CHAP (Chapter) Indicator
Indicates current chapter number.
Introduction
Display Window
j RDM (Random) Indicator
Indicates when playing in random order.
k AGL (Angle) Indicator
Indicates when playing a scene recorded with
multi angles.
l Remote Control Indicator
Indicates when Remote Control signal is
received.
m Disc Indicator
BD: Indicates when an BD-ROM disc is loaded.
HD DVD: Indicates when an HD DVD disc is
loaded.
DVD: Illuminates when a DVD disc is loaded.
CD: Illuminates when a Audio CD, MP3/WMA or
JPEG disc is loaded.
n Character Indicators
Indicates total playing time, elapsed time, title
number, chapter number or message, etc.
11
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 12
MARKER: Marks any point during playback.
Remote Control
SEARCH: Displays Marker
Search menu.
a
AUDIO ( ): Selects an audio
language or audio channel.
d
c
X (PAUSE/STEP): Pauses
playback.
REPEAT: Repeat a desired section.
RESUME PLAY*: Resumes playback from the location last
stopped when a disc menu
appears.
ANGLE ( ): Selects a disc
camera angle, if available.
N (PLAY): Starts playback.
m / M (SCAN): Search
backward or forward.
. / > (SKIP): Go to next or
previous chapter.
b Color (A, B,C, D) buttons: Are
used for some BD-J or HD DVD
interactivity applications.
They are also used for [PHOTO]
and [MUSIC] menu.
d TV Control Buttons: See page
31.
DISPLAY: Accesses On-Screen
Display.
0-9 numerical buttons: Select
numbered options in a menu.
HOME: Accesses the Home
Menu.
VIDEO PIP*: Switches PIP function on or off, if available
(BD-ROM only).
DISC MENU: Accesses menu on
a disc.
ENTER ( ): Acknowledges
menu selection.
TV POWER: Switches the TV ON
or OFF.
SUBTITLE ( ): Selects a
subtitle language.
Direction buttons: Select an
option in the menu.
a POWER: Switches the player ON
or OFF.
x (STOP): Stops playback.
c
SUBTITLE ON/OFF: Switches
the subtitle on or off.
A-B: Repeat sequence.
b
TITLE/POP UP: Displays the
DVD or HD DVD’s title menu or
BD-ROM’s popup menu, if available.
RETURN (O): Exits the menu.
CLEAR: Removes a mark on the
Marker Search menu or a number
when setting the password.
CURSOR*: Use while a HD DVD
with support for cursor use is
playing.
RESOLUTION: Sets the output
resolution for HDMI and
COMPONENT VIDEO OUT
jacks.
* Depending on a disc type or
the pre-recorded contents of
the HD DVD and BD, different
functions may be executed
than other media or there are
no responses when pressing
some buttons.
OPEN/CLOSE (Z): Opens and
closes the disc tray.
Remote Control Operation
Point the Remote Control at the remote sensor and
press the buttons.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
12
Remote Control Battery Installation
Remove the battery cover on
the rear of the Remote Control,
and insert two R03 (size AAA)
batteries with
and
matched correctly.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 13
Installation and Setup
Rear Panel
b
f
c
d
e
g
a AC IN connector
Connect the supplied power cord.
b COMPONENT VIDEO OUT (Y Pb Pr)
Connect to a TV with Y Pb Pr inputs.
c DIGITAL AUDIO OUT (OPTICAL)
Connect to digital (optical) audio equipment.
d HDMI OUT (Type A)
Connect to TV with HDMI inputs. (Interface for
digital audio and video)
e LAN port
Connect a network with an always-on
broadband connection.
f VIDEO OUT
Connect to a TV with video inputs.
g 2CH AUDIO OUT (Left/Right)
Connect to a TV with 2 channel audio inputs.
Installation and Setup
a
13
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 14
HDMI connection
HDMI compatible TV
HDMI
If you have a HDMI TV or monitor, you can connect
it to this player using a HDMI cable.
1. Connect the HDMI jack on the player to the HDMI
jack on a HDMI compatible TV or monitor (H).
2. Set the TV’s source to HDMI (refer to TV’s
Owner’s manual).
H
Notes:
You must select a HDMI audio output and a
maximum sampling frequency that your TV
accepts using [HDMI] and [Sampling Freq.]
options on the setup menu (See page 21).
If a connected HDMI device does not accept the
audio output of the unit, the HDMI device’s audio
sound may be distorted or may not output.
Tip:
When you use HDMI connection, you can change
the resolution for the HDMI output. (Refer to
“Resolution Setting” on page 18.)
Cautions
Changing the resolution when the connection has
already been established may result in malfunctions. To solve the problem, turn off the player and
then turn it on again.
When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this
case, check the the HDMI connection, or disconnect the HDMI cable.
If there is noise or lines on the screen, please
check the HDMI cable (length is generally limited
to 15ft).
Rear of the player
Additional Information for HDMI
When you connect a HDMI or DVI compatible
device make sure of the followings:
- Try switching off the HDMI/DVI device and this
player. Next, switch on the HDMI/DVI device
and leave it for around 30 seconds, then switch
on this player.
- The connected device’s video input is set correctly for this unit.
- The connected device is compatible with
720x576p, 1280x720p, 1920x1080i or
1920x1080p video input.
Not all HDCP-compatible DVI devices will work
with this player.
- The picture will not be displayed properly with
non-HDCP device.
- This player does not playback and TV screen is
changed to black screen
14
5/2/08
11:05 AM
Page 15
Connections to Your TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
Rear of TV
L
Tips
Depending on your TV and other equipment you
wish to connect, there are various ways you
could connect the player. Use only one of the
connections described below.
Please refer to the manuals of your TV, Stereo
System or other devices as necessary to make
the best connections.
Caution
– Make sure the player is connected directly to the
TV. Tune the TV to the correct video input channel.
– Do not connect the player’s AUDIO OUT jack to
the phono in jack (record player) of your audio
system.
– Do not connect your player via your VCR. The
image could be distorted by the copy protection
system.
Component Video Connection
Connect the COMPONENT VIDEO OUT jacks on
the player to the corresponding input jacks on the
TV using Y Pb Pr cables (C).
VIDEO
INPUT
AUDIO INPUT
A
COMPONENT VIDEO INPUT
Y
R
V
Pb
Pr
C
Rear of the
player
Installation and Setup
BH200-P-ASGPLLK-ENG
Tip:
When you use COMPONENT VIDEO OUT connection, you can change the resolution for the output.
(Refer to “Resolution setting” on page 18.)
Video Connection
Connect the VIDEO OUT jack on the player to the
video in jack on the TV using a video cable (V).
Audio (Left/Right) Connection
Connect the left and right 2CH AUDIO OUT jacks of
the player to the audio left and right IN jacks on the
TV using the audio cables (A).
15
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 16
Connecting to an Amplifier
Make one of the following connections, depending
on the capabilities of your existing equipment.
Note:
Since many factors affect the type of audio output,
see “The unit’s Audio Output Specifications” on page
37 for details.
Connecting to an Amplifier via 2 Channel
Audio Output
Connect the Left and Right 2CH AUDIO OUT jacks
on the player to the audio left and right in jacks on
your amplifier, receiver, or stereo system, using
audio cables (A).
Connecting to an Amplifier via Digital Audio
Output (Optical)
1. Connect the player’s DIGITAL AUDIO OUT jack
to the corresponding in jack on your amplifier.
Use a digital audio cable (O).
Notes:
You must select a digital audio output and a
maximum sampling frequency that your Amplifier
(or AV receiver) accepts using [SPDIF], [HDMI]
and [Sampling Freq.] options on the setup menu
(See page 21).
With digital audio connection (SPDIF or HDMI),
Disc Menu button sounds of BD-ROM or HD DVD
may not be heard if the [SPDIF] or [HDMI] option
is set to [Primary Pass-Thru].
If the audio format of the digital output does not
match the capabilities of your receiver, the receiver
will produce a strong, distorted sound or no sound at
all.
Multi-channel Digital Surround Sound via digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
To see the audio format of the current disc in the
on-screen display, press AUDIO.
Rear of the player
2. You will need to activate the player’s digital
output. (See “[AUDIO] Menu” on page 21.)
Connecting to an Amplifier via HDMI Output
1. Connect the player’s HDMI OUT jack to the
corresponding in jack on your amplifier. Use an
HDMI cable (H1).
2. You will need to activate the player’s digital
output. (See “[AUDIO] Menu” on page 21.)
Tip:
Connect the amplifier’s HDMI output jack to HDMI
input jack on your TV using an HDMI cable (H2) if
your amplifier has HDMI output jack.
A
O
H1
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video Receiver that supports one or more of
the audio formats supported by your player. Check
the receiver manual and the logos on the front of the
receiver. (PCM Stereo, PCM Multi-Ch, Dolby Digital
and/or DTS)
HDMI OUTPUT
L
R
AUDIO INPUT
OPTICAL
DIGITAL INPUT
HDMI INPUT
Amplifier (Receiver)
H2
HDMI
HDMI compatible TV
16
5/2/08
11:05 AM
Page 17
Internet connection
This player can be connected to a local area network (LAN) via the LAN port on the rear panel.
After making the physical connection the player
needs to be set up for network communication. This
is done from the [Setup] menu — see “[NETWORK]
Menu” on page 23 for detailed instructions.
This connection is used to access special HD DVD
or BD-ROM sites.
Connect the player’s LAN port to the corresponding
port on your Modem or Router using a LAN cable.
Use a commercially available straight LAN cable
(Category 5/CAT5 or better with RJ45 connector).
•
•
•
•
Cautions:
When plugging or unplugging the LAN cable, hold
the plug portion of the cable. When unplugging,
do not pull on the LAN cable but unplug while
pressing down on the lock.
Do not connect a modular phone cable to the
LAN port.
•
Since there are various connection configurations, please follow the specifications of your
telecommunication carrier or internet service
provider.
•
•
Rear of the player
•
•
Broadband
Service
Router
Notes:
• Depending on the internet service provider (ISP),
the number of devices that can receive internet
service may be limited by the applicable terms of
service. For details, contact your ISP.
• Our company is not responsible for any malfunction of the player and/or the internet connection
feature due to communication errors/malfunctions associated with your broadband internet
connection, or other connected equipment.
• Our company is not responsible for any trouble
in your internet connection.
•
•
If you wish to use a wireless network to connect
the player, you will need to use a wireless LAN
ethernet adapter to connect the player to the network.
The features of HD DVD or BD-ROM discs made
available through the Internet Connection feature
are not created or provided by our company, and
our company is not responsible for their functionality or continued availability. Some disc related
material available by the Internet Connection
may not be compatible with this player. If you
have questions about such content, please contact the producer of the disc.
Some internet contents may require a higher
bandwidth connection.
Even if the player is properly connected and configured, some internet contents may not operate
properly because of internet congestion, the
quality or bandwidth of your internet service,
problems at the provider of the content or compatibility issues.
Some internet connection operations may not be
possible due to certain restrictions set by the
Internet service provider (ISP) supplying your
broadband Internet connection.
Any fees charged by an ISP including, without
limitation, connection charges are your responsibility.
A 10 Base-T or 100 Base-TX LAN port is
required for connection to this player. If your
internet service does not allow for such a connection, you will not be able to connect the player.
You must use a Router to use xDSL service.
A DSL modem is required to use DSL service
and a cable modem is required to use cable
modem service. Depending on the access
method of and subscriber agreement with your
ISP, you may not be able to use the internet connection feature contained in this player or you
may be limited to the number of devices you can
connect at the same time. (If your ISP limits subscription to one device, this player may not be
allowed to connect when a PC is already connected.)
The use of a “Router” may not be allowed or its
usage may be limited depending on the policies
and restrictions of your ISP. For details, contact
your ISP directly.
Your ISP may protect this player from being connected to network when confirming MAC
ADDRESS. In that case, contact your ISP to
request to initialize MAC ADDRESS.
Installation and Setup
BH200-P-ASGPLLK-ENG
17
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 18
Resolution Setting
The player provides several output resolutions for
HDMI OUT and COMPONENT VIDEO OUT jacks.
You can change the resolution using [Setup] menu
or pressing the RESOLUTION button in complete
stop mode.
Auto – If the HDMI OUT jack is connected for
TVs providing display information (EDID), automatically selects the resolution best suited to the
connected TV (1080p, 1080i, 720p or 576p).
(only for HDMI connection)
1080p – Outputs 1080 lines of progressive
video. (only for HDMI connection)
1080i – Outputs 1080 lines of interlaced video.
720p – Outputs 720 lines of progressive video.
576p – Outputs 576 lines progressive video.
576i – Outputs 576 lines of interlaced video.
(only for COMPONENT VIDEO OUT connections)
Available resolution according to
connection
HDMI OUT connection
• Auto, 1080p, 1080i, 720p and 576p are available.
• 576i is not available.
• If you select a resolution manually and then connect the HDMI jack to TV and your TV does not
accept it, the resolution setting is set to [Auto].
• If you select a resolution that your TV does not
accept, the warning message appears for a while
then it disappear. You must select a resolution that
your TV does accept.
• The 1080p video output frame rate may be automatically set to either 24Hz or 50Hz (or 60Hz)
depending both on the capability and preference
of the connected TV and based on the native
video frame rate of the content on the Blu-ray disc
or HD DVD.
COMPONENT VIDEO OUT connection
• 1080i, 720p, 576p and 576i are available.
How to change the resolution using
RESOLUTION button
• The resolution may be limited depending on the
title in BD-ROM, HD DVD and DVD.
Press RESOLUTION button in complete stop mode.
• If the disc is copy protected, the resolution will be
changed to 576p or 480p automatically.
• 1080p is not available.
RESOLUTION button
How to change the resolution using
Setup menu
1. Press HOME and the Home Menu appears.
2. Select [Setup] and press ENTER. The Setup
menu appears.
3. Use v / V to select [DISPLAY] option then press
B to move to the second level.
4. Use v / V to select the [Resolution] option then
press B to move to the third level.
5. Use v / V to select the desired resolution then
press ENTER to confirm your selection.
18
VIDEO OUT connection
• The resolution of the VIDEO OUT jack is fixed to
576i.
Notes:
• Depending on your display, some of the resolution
settings may result in the picture disappearing or
an abnormal picture appearing. In this case, press
STOP twice then RESOLUTION repeatedly until
the picture re-appears.
• This player supports simultaneous output of video
on its HDMI OUT and COMPONENT VIDEO OUT
jacks. The resolution on the HDMI output will be
the same as the resolution output on the component video output. Thus, because the HDMI output
can change automatically to match the maximum
available resolution of your display when
[Resolution] option is set to [Auto] on the setup
menu, if you connect both the HDMI output and
component video output, the resolution on the
component video output will change if the HDMI
output Auto-adjusts.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 19
Initial Settings
[DISPLAY] Menu
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and the
Setup menu, among other things. For details on
each Setup menu item, see pages 19 to 24.
To go to the next level:
Press B on the Remote Control.
To go back to the previous level:
Press b on the Remote Control.
General Operation
1. Press HOME and the Home Menu appears.
2. Select [Setup] and press ENTER. The Setup
menu appears.
TV Aspect Ratio
[4:3 Letter Box] – Select when a standard 4:3
TV is connected. Displays theatrical images with
masking bars above and below the picture.
[4:3 Pan Scan] – Select when a standard 4:3 TV
is connected. Displays pictures cropped to fill
your TV screen. Both sides of the picture are cut
off.
[16:9 Wide] – Select when a 16:9 wide TV is
connected.
Note:
You cannot select [4:3 Letter Box] and [4:3 Pan
Scan] option when the resolution is set to higher
than 720p.
Installation and Setup
To display and exit the Menu:
Press HOME and the Home Menu appears. Select
[Setup] then press ENTER, and Setup menu
appears.
Press RETURN or HOME to exit the Setup menu.
Resolution
Sets the output resolution of the Component and
HDMI video signal.
Refer to “Resolution Setting” on page 18 for details
about the resolution.
3. Use v / V to select the desired option then press
B to move to the second level. The screen
shows the current setting for the selected item,
as well as alternate setting(s).
4. Use v / V to select the second desired option
then press B to move to the third level.
5. Use v / V to select the desired setting then
press ENTER to confirm your selection. Some
items require additional steps.
6. Press RETURN or HOME to exit the Setup
menu.
19
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 20
[DISPLAY] Menu (Continued)
White NR (White Noise Reduction)
Enhance the video quality by reducing the white
(random) noise of the digital video.
The higher White NR level makes the video softer.
Block NR (Block Noise Reduction)
Set to [On] to reduce the block noise, which may
appear especially on fast-moving pictures, produced
in the MPEG compression process.
Mosquito NR (Mosquito Noise Reduction)
Video Mode
Select the video mode during play.
[Default]
– The video is adjusted automatically. Qdeo delivers rich high-definition video
quality through a suite of advanced QuietVideo™
technologies. You cannot adjust other video
adjustment options.
Set to [On] to reduce the mosquito (scattering) noise
produced in the MPEG compression process.
[LANGUAGE] Menu
[User] – You can make further adjustments for
video using [Video Adjustment],
[Color Adjustment], [White NR], [Block NR], and
[Mosquito NR] options.
Video Adjustment
You can adjust Contrast, Brightness, Sharpness or
Color.
Select a language for the Setup menu and onscreen display.
2. Use v / V to select a desired option then use
b / B to adjust the value.
• Select [Default] option then press ENTER to
reset the video adjustment.
• Select [Close] option then press ENTER to exit
the [Video Adjustment] menu.
Disc Menu / Disc Audio / Disc Subtitle
Color Adjustment
You can adjust picture’s color.
1. Select [Color Adjustment] option then press
ENTER.
The menu for color adjustment will appear
2. Use v / V to select a desired option then use
b / B to adjust the value.
• Select [Default] option then press ENTER to
reset the color adjustment.
• Select [Close] option then press ENTER to exit
the [Color Adjustment] menu.
20
Display Menu
1. Select [Video Adjustment] option then press
ENTER.
The menu for video adjustment will appear
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original] – Refers to the original language in
which the disc was recorded.
[Other] – To select another language, press
number buttons then ENTER to enter the corresponding 4-digit number according to the language code list on page 33.
[Off] (for Disc Subtitle) – Turn off Subtitle.
Note:
Depending on a disc, your language setting may not
be worked for some disc.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 21
[AUDIO] Menu
Each disc has a variety of audio output options. Set
the player’s Audio options according to the type of
audio system you use.
Note:
Since many factors affect the type of audio output,
see “The unit’s Audio Output Specifications” on page
37 for details.
Sampling Freq. (Maximum Sampling Frequency)
[192KHz] – Select this if your A/V Receiver or
Amplifier is capable of handling 192 KHz signals.
[96KHz] – Select this if your A/V Receiver or
Amplifier is NOT capable of handling 192 KHz
signals. When this choice is made, this unit automatically converts any 192 KHz signals to
96 KHz so your system can decode them.
Check the documentation for your A/V Receiver or
Amplifier to verify its capabilities.
HDMI / SPDIF (Digital Audio Output)
Select the output sound format when a device
equipped with an HDMI or Digital Audio input jack is
connected to the HDMI OUT or DIGITAL AUDIO
OUT jack on this player.
[PCM Stereo] – Select if you connect this unit’s
HDMI OUT or DIGITAL AUDIO OUT jack to a
device with two-channel digital stereo decoder.
DRC (Dynamic Range Control)
During the disc encoded in Dolby Digital or Dolby
Digital Plus is playing back, you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones). This allows you to listen to a movie at a
lower volume without losing clarity of sound. Set
DRC to [On] for this effect.
Installation and Setup
[48KHz] – Select this if your A/V Receiver or
Amplifier is NOT capable of handling 192 KHz
and 96 KHz signal. When this choice is made,
this unit automatically converts any 192 KHz and
96 KHz signals to 48 KHz so your system can
decode them.
[PCM Multi-Ch] (HDMI only) – Select if you
connect this unit’s HDMI OUT jack to a device
with multi-channel digital decoder.
[DTS Re-Encode] – Select if you connect this
unit’s HDMI OUT or DIGITAL AUDIO OUT jack to
a device with DTS decoder.
[Primary Pass-Thru] – Select if you connect this
unit’s DIGITAL AUDIO OUT and HDMI OUT jack
to a device with LPCM, Dolby Digital and DTS.
Notes:
• When [HDMI] option is set to [PCM Multi-CH], the
audio may output as PCM Stereo if the PCM
Multi-Ch information is not detected from HDMI
device with EDID.
• When [HDMI] and [SPDIF] options are set to
[DTS Re-Encode], the DTS audio will output on
BD and HD DVD advanced disc, and the original
audio will output on the other discs.
21
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 22
[LOCK] Menu (Parental Control)
Rating
Blocks playback of rated disc based on their content. (Not all discs are rated.)
1. Select [Rating] on the [LOCK] menu then
press B.
Password
You can enter or change the password.
1. Select [Password] option on the [LOCK] menu
then press B.
2. To create new password, press ENTER when the
[New] option is highlighted. Input new password
and press ENTER. Enter it again and press
ENTER to verify.
To change the password, press ENTER when the
[Change] option is highlighted, then input old
password and press ENTER. Input new password
and press ENTER. Enter it again and press
ENTER to verify.
To delete the password, select [Delete] option
then press ENTER, then input old password and
press ENTER. The password is deleted.
Tip:
If you make a mistake before pressing ENTER,
press CLEAR. Then input the correct password.
If you forget your password
If you forget your password, you can clear it using
the following steps:
2. To access this option, you must input the password you have created. If you have not yet
entered password, you will be prompted to do so.
Input a password and press ENTER. Enter it
again and press ENTER to verify. If you make a
mistake before pressing ENTER, press CLEAR.
3. Select a rating from 1 to 8 using the v / V buttons.
[Rating 1-8] – Rating one (1) has the most
restrictions and rating eight (8) is the least
restrictive.
[Unlock] – If you select unlock, parental control
is not active and the disc plays in full.
4. Press ENTER to confirm your rating selection.
BD Age
Set an age limit of BD-ROM play.
1. Select [BD Age] on the [LOCK] menu then
press B.
2. Follow step 2 as shown above (Rating).
3. Use number buttons to input an age limit for
BD-ROM viewing.
[255] – All BD-ROM can be played.
[0-254] – Prohibits play of BD-ROM with corresponding ratings recorded on them.
4. Press ENTER to confirm your selection.
1. Remove any disc that might be in the player.
2. Select [Password] option.
3. Use Number buttons to enter the 6-digit number
“210499”.
The “PIN CLEAR” appears in the display window
and the password is deleted.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 34.
1. Select [Area Code] on the [LOCK] menu then
press B.
2. Follow step 2 as shown above (Rating).
3. Select the first character using v / V buttons
then press ENTER.
4. Select the second character using v / V buttons
then press ENTER to confirm your selection.
22
5/2/08
11:05 AM
Page 23
[NETWORK] Menu
IP Setting
Some HD DVD or BD-ROM discs may enable you to
access special HD DVD or BD-ROM sites, if you
connect the player to the Internet. For example, if an
HD DVD or BD-ROM site includes content such as
links to future movie trailers, you can watch the
downloaded on-line content on the player.
You do not need to connect to a PC to use this function.
This option is available only if [IP Mode] option is set
to [Static IP].
Use the v / V / b / B buttons to select a field; use
the number buttons to enter a value. Press ENTER
when [OK] is highlighted to finish and exit the
screen.
Preparations:
• This feature requires an always-on broadband
internet connection. (See page 17.)
• An BD-ROM or HD DVD disc compatible with
this feature is required. Not all BD-ROM or
HD DVD discs are compatible.
Although not directly related to the Internet connection, some BD-ROM or HD DVD discs may require
the following settings to be configured.
User Information
1. Select [User Information] on the [NETWORK]
menu then press B.
2. Input characters for user ID by pressing v / V.
To shift the position, press b / B .
Up to 10 characters can be input.
3. Press ENTER to shift to [Password] option.
IP Mode
If there is a DHCP server on the local area network
(LAN), this player will automatically be allocated an
IP address. If you’re using a broadband router or
broadband modem that has a DHCP (Dynamic
Host Configuration Protocol) server function, select
[Dynamic IP]. The IP address will automatically be
determined.
If there is no DHCP server on the network and you
want to set the IP address manually, select
[Static IP] then set the [IP Address], [Subnet Mask],
[Gateway] and [DNS Server] using [IP Setting]
option.
Note:
The [IP Mode] menu shows if the internet is connected or not. “ ” will appear when connection is
failed.
4. Input characters for password by pressing v / V.
To shift the position, press b / B .
Up to 10 characters can be input.
Tip:
If you make a mistake, press CLEAR. Then input
the correct characters.
Installation and Setup
BH200-P-ASGPLLK-ENG
Network Speed
Select a speed according to the specification of your
LAN.
[Low Speed] – Lower than 1 Mbps
[Mid Speed] – 1-10 Mbps
[High Speed] – Higher than 10 Mbps
Cookie Setting
Select whether you wish to accept “cookies” or not.
[Accept] – Cookies are accepted.
[Not Accept] – Cookies are rejected. This may
disable some services on web pages.
Note:
If you select to accept “cookies”, the BD-ROM or
HD DVD internet services you use may record or
track information about your use of the player and/or
those sites. If you do not choose to allow cookies,
some or all features of a site may not properly function.
23
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 24
[OTHERS] Menu
[Built-In Memory] – Saves the downloaded online contents in built-in memory.
[USB Memory] – Saves the downloaded on-line
contents in the USB Flash Drive if connected.
Button Sound
You can hear beep sound when you press a touch
button on the front panel. Set [On] for this effect.
Java Font Size BD
You can adjust the default text size displayed for
the BD-J contents during BD-ROM playback.
This setting is only valid when BD-J contents do not
set the size of text.
Please select a font size bigger than 24 when the
player is connected with an HD TV.
1080p Film Mode
When the resolution is set to 1080p, select [On] for
smooth presentation of film material (1080/24p or
720/24p video) with an HDMI-equipped display compatible with 1080/24p input.
Notes:
• When you select [On], you may experience some
picture disturbance when the video switches video
and film material. In this case, select [Off].
• Even when [1080p Film Mode] is set to [On], if
your TV is not compatible with 1080/24p, the
actual frame frequency of the video output will
be 60 Hz or 50 Hz.
Slow/Step DVD HD DVD BD
You can set up the operations of the X (Pause) and
M (Forward Scan) while the playback is paused.
[Off] – If you press X while the playback is
paused and the picture play backs in normal.
If you press M while the playback is paused
and the picture play backs in fast forward.
[On] – If you press X while the playback is paused
and the picture play backs in frame-by-frame.
If you press M while the playback is paused
and the picture play backs in slow motion.
Note:
We recommend setting the [Slow/Step] option to
[Off] for HD DVD interactivity.
BD Storage BD
This player includes memory that is used to store
some BD-ROM disc related information, including
downloaded on-line content. The disc you are using
will control how long this information is retained.
24
HD-DVD Storage HD DVD
You can erase or copy the downloaded on-line content for HD DVD in the built-in memory or USB
Flash Drive.
1. Select [HD-DVD Storage] on the [OTHERS]
menu then press B.
The [Persistence Storage] menu will appear.
2. Select [Built In Memory] or [USB1] then press B.
[Built-In Memory] – Shows the contents in the
built-in memory.
[USB 1] – Shows the contents in the USB Flash
Drive.
3. Select a folder then press press B.
The contents in the folder will appear.
4. Highlight an option and then press ENTER.
[Copy] – Copies the contents from the built-in
memory to USB Flash Drive. (or from USB Flash
Drive to the built-in memory).
[Delete] – Deletes the contents in the built-in
memory or USB Flash Drive.
[Close] – Returns to the [Persistence Storage]
menu.
5. Select an option then press ENTER.
Note:
The [Common Area] folder is created by default if
this folder is not existed in the [Built-In Memory].
Initialize
You can reset the player to its original factory settings and initialize the BD Storage or HD-DVD
Storage.
1. Select [Initialize] option then press B.
2. Press v / V to select the desired option then
press ENTER.
The confirm message will appear.
[Factory Set] – If you need to, you can reset the
player to all its factory settings. Some options
cannot be reset. (Rating, Password, Area Code
and BD/HD Storage)
[BD Flash Format] – Initializes the BD contents
from the built-in memory: BD contents recorded
on the built-in memory will be erased.
[HD-DVD Flash Format] – Initializes the
HD-DVD contents from the built-in memory: HDDVD contents recorded on the built-in memory
will be erased.
3. Use b / B to select [Yes] or [No] then press
ENTER.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 25
Operations
General playback features
1. Load your chosen disc in the tray, with the playback side down.
2. Start playback using the HOME menu (See page 9).
Buttons
Operations
Discs
OPEN / CLOSE (Z)
Opens or closes the disc tray.
All Discs
x (STOP)
Stops the playback.
The unit records the stopped point, depending on the
disc. “Xx” appears on the screen briefly. Press
N (PLAY) to resume playback (from the scene point). If
you press STOP (x) again or unload the disc (“x”
appears on the screen.), the unit will clear the stopped
point. (Xx = Resume Stop, x = Complete Stop)
Note:
The resume point may be cleared when a button is
pressed (for example; POWER, OPEN/CLOSE, etc).
All Discs
On HD DVD advanced title and BD interactive title, the
unit will be in Complete Stop mode if you press STOP
once during playback.
HD DVD
BD
RESUME PLAY
Disc menu will appear if you press DISC MENU once.
To resume playback, press RESUME PLAY.
Notes:
• The RESUME PLAY may not work on some discs.
• On other disc, RESUME PLAY is operated as
N (PLAY).
HD DVD
BD
X (PAUSE)
During playback, press X to pause playback.
Tip: During Audio CD or MP3/WMA playback, press X
once again to resume playback.
Press X repeatedly to play Frame-by-Frame.
All Discs
DVD
HD DVD
BD
Note: X (PAUSE) button’s operation are differ depending on the [Slow/Step] option setting on the setup menu.
(See page 24.)
. / > (SKIP)
During playback, press . or > to go to the next
chapter/track/file or to return to the beginning of the
current chapter/track/file.
Press . twice briefly to step back to the previous
chapter/track/file.
All Discs
m / M (SCAN)
During playback, press SCAN (m or M) repeatedly
to select the required scan speed.
- DVD, HD DVD, BD: 5 steps,
- Audio CD, MP3, WMA: 3 steps
All Discs
While the playback is paused, press SCAN M repeatedly to play in slow motion (4 steps, forward only).
DVD
HD DVD
Operation
DVD ACD MP3
WMA
BD
Note: M (SCAN) button’s operation are differ depending on the [Slow/Step] option setting on the setup menu.
(See page 24.)
Continued t
25
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 26
General playback features (Continued)
Buttons
Operations
REPEAT
During playback, press REPEAT repeatedly to select a
desired repeat mode.
DVD, HD DVD, BD: Chapter/Title/Off
Audio CD, MP3, WMA: Track/All/Off
Note:
If you press > once during Repeat Chapter/Track
playback, the repeat playback cancels.
A-B
Discs
DVD
MP3
During playback, each press of A-B button to select
DVD
point A and point B and repeats a sequence from point A
(Starting point) to point B (End point).
To cancel the sequence, press A-B.
BD
WMA
ACD
BD
ACD
TITLE/POP UP
If the current DVD, HD DVD or BD-ROM disc has a
menu, the Title menu or Popup menu appears on the
screen. Depending on the disc, the menu may not be
available.
DVD
HD DVD
BD
DISC MENU
The menu appears on the screen. Depending on the
disc, the menu may not be available.
DVD
HD DVD
BD
ANGLE (
During playback of the disc contains scenes recorded at DVD
different camera angles, press ANGLE repeatedly to
select a desired angle.
Note:
When you are playing a disc containing scenes recorded
at different camera angles, the angle indicator will
appear on the TV screen for a while and display window
during scenes recorded at different angles as an indication that angle switching is possible.
HD DVD
BD
During playback, press SUBTITLE repeatedly to select a DVD
desired subtitle language.
HD DVD
BD
SUBTITLE ON/OFF
During playback, press SUBTITLE ON/OFF to switch
the subtitle on or off.
DVD
HD DVD
BD
AUDIO (
During playback, press AUDIO repeatedly to hear a different audio language or audio track.
Notes:
• Some discs allow you to change audio selections only
via the disc menu. If this is the case, press
TITLE/POPUP or DISC MENU button and choose the
appropriate audio from the selections on the disc
menu.
• Immediately after you have switched sound, there
may be a temporary discrepancy between the display
and actual sound.
• On BD-ROM disc, the multi audio format (5.1CH or
7.1CH) is displayed with [MultiCH] in the on-screen
display.
DVD
HD DVD
BD
)
SUBTITLE (
)
)
Notes on general features:
•
•
26
When you turn on the player or replace a disc, the player returns to the initial default setting. Depending
on a disc, a specific type of audio the disc has is output.
Depending on the pre-recorded contents of the HD DVD or BD, some functions may not be available or
may be operated differently than other media.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 27
If a disc menu screen is displayed
DVD
HD DVD
BD
The menu screen may be displayed first after loading
a disc which contains a menu.
Use the b / B / v / V buttons to select the title/chapter you want to view, then press ENTER to start
playback.
Time Search DVD
BD
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback.
2. Press v / V to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. For example, to
find a scene at 2 hours, 10 minutes, and
20 seconds, enter “21020” and press ENTER. If
you enter the wrong numbers, press CLEAR to
remove the numbers you entered. Then input the
correct numbers.
4. Press ENTER to confirm. Playback starts from
the selected time.
Note:
This function may not work on some disc or titles.
Marker Search DVD
Using Color (A, B, C, D) Buttons
BD HD DVD
These buttons are available only during BD-J
contents playback or during HD DVD interactivity
contents playback. Use the appropriate buttons as
indicated by the display. Depending on the disc
contents, the functions of each button may differ.
Note:
On HD DVD disc, a menu or on-screen display may
be disappeared after a while depending on the disc
information.
Displaying Disc Information On-Screen
DVD
HD DVD
BD
You can display various information about the disc
loaded on-screen.
1. Press DISPLAY to show various playback information.
The items displayed differ depending on the disc
type or playing status.
BD
You can start playback from up to nine memorized
points. To enter a marker, press MARKER at the
desired point on the disc. The Marker icon appears
on the TV screen briefly. Repeat to enter up to nine
markers.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The marker search menu appears on the screen.
2. Within 10 seconds, press b / B to select a marker number that you want to recall or clear.
3. Press ENTER and playback starts from the
marked scene. Or, Press CLEAR and the marker
number is erased from the list.
4. You can play any marker by inputting its number
on the marker search menu.
Notes:
• This function may not work on some disc or
titles.
• All marked points are cleared if you press
STOP (x) twice or unload the disc. (complete
stop).
Screen Saver
2. During BD-ROM or DVD playback, you can
select an item by pressing v / V and change or
select the setting by pressing b / B.
Title – Current title number/total number of
titles.
Chapter – Current chapter number/total number of chapters.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – Selected angle/total number of angles.
Operation
To enter a Marker
Notes:
• If no button is pressed for a few seconds, the onscreen display disappears.
• A title number cannot be selected on some discs.
• An item may not be available on some discs or
titles.
• If HD DVD interactivity or BD interactive title is
playing back, some setting information is
displayed on the screen but prohibited to be
changed.
The screen saver appears when you leave the
player in Stop mode for about five minutes.
27
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Hybrid Discs BD
Page 28
HD DVD
If you insert a Hybrid Disc, you must select a layer
to play back.
Hybrid Disc?
- HD DVD Twin Format Disc with both HD DVD and
DVD layers on one side
- BD-ROM Disc with both BD and DVD (or CD) layers on one side
1. Insert a Hybrid Disc.
The choice menu will appear.
2. Select the primary format (HD DVD or BD) or
secondary format (DVD or CD) on the menu
then press ENTER.
The selected playback format begins.
Some HD DVD discs may include game software
and drawing software. If they do you can use the
cursor function for some software.
1. Press CURSOR while a disc with support for
cursor use is playing.
2. Use the eight direction buttons to move the cursor.
Tip:
Example: Game/drawing software
Move the cursor to select the game target or selection item. For details on actual operations, also
refer to the operations guide for the disc.
Notes:
• To change the format, press HOME then select
[Movie] option and press ENTER. The choice
menu will appear.
To play back the CD layer on the Hybrid Disc,
select [Music] option on the HOME menu.
• You can only use b / B, ENTER, OPEN/CLOSE
and POWER buttons when the choice menu is
displayed.
Internet connection feature
• You cannot change the format during playback.
1. Check the internet connection and configure.
(See pages 17 and 23.)
Last Scene Memory DVD
2. Insert an HD DVD or BD-ROM disc with this feature and start the playback.
This unit memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
Notes:
• Settings are stored in memory for use any time.
• This unit does not memorize settings of a disc if
you switch off the unit before commencing to
play it.
• Last Scene Memory function for a previous DVD
title is erased once a different DVD title is
played.
28
Using the cursor function HD DVD
BD
HD DVD
Some HD DVD or BD-ROM discs may enable you to
access special HD DVD or BD-ROM sites, if you
connect the player to the Internet. For example, if an
HD DVD or BD-ROM site includes content such as
links to future movie trailers, you can watch the content on the player via the Internet.
3. Select an item from the menu.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 29
Playing an Audio CD or
MP3/WMA files
The player can play Audio CDs and MP3/WMA files.
Before playing MP3/WMA files, read “MP3/WMA
audio file requirement” on right.
MUSIC menu options
1. Use v / V to select a track or file on the MUSIC
menu then press ENTER.
The menu options appear.
2. Use v / V to select an option, then press
ENTER.
1. Insert Audio CD or a disc containing MP3/WMA
files, or connect the USB Flash Drive containing
MP3/WMA files
2. Press HOME and Home Menu appears.
3. Select [Music] then press ENTER.
The MUSIC menu appears on the TV screen.
Note:
When the USB Flash Drive is connected and a
disc is inserted simultaneously, the menu for
selecting a media will appear. Select a media
then press ENTER.
• [Play] Starts playback the selected track or
file.
• [Select Play] Plays back only the marked
track(s) or file(s). Use MARKER for selecting
the multiple files or tracks.
• [Random] Starts or stops random playback.
4. Use v/V to select a track or file then press
N (PLAY). Playback starts.
You can use variable playback functions. Refer
to pages 25-26.
5. To stop playback at any time, press STOP (x).
Tips:
• The playback may start automatically if the
Audio CD inserted.
•
Select a folder then press ENTER and you can
view the files in the folder. If you want to move to
the upper directory, use v/V to highlight
[UP Folder] and press ENTER.
•
On the MUSIC menu, use red or blue color button to move to the previous or next page.
•
The equalizer indicator is not coupled with the
music in play back.
•
If there is impossible code to express in the file
name, it may be displayed as illegible.
By pressing > during random playback, the
unit selects another track and resumes random playback.
• [Unmark All] Unmarks all marked files or
tracks.
• [Close] Exits menu options. Also you can dis-
appear it by pressing RETURN button.
Note:
You cannot use [Select Play] and [Random]
functions simultaneously.
Operation
Example) Audio CD
MP3/WMA audio file requirement
File extensions: “.mp3”, “.wma”.
Sampling frequency: 8 - 48 kHz
Bit rate: 8 - 320kbps
CD-R, DVD±R/RW/RAM, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format.
Maximum Files/Disc:
Less than 1999 (total number of files and folders)
Notes on MP3/WMA file
Depending on the size and number of the
MP3/WMA files, it may take several minutes to
read the contents of the media.
29
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 30
Viewing a JPEG file
Options during viewing a photo file
in full screen
This unit can play JPEG files. Before playing JPEG
recordings, read “Photo file requirement” on below.
1. Follow steps 1-4 as shown left (Viewing a JPEG
file).
1. Insert a disc containing JPEG files, or connect
the USB Flash Drive containing JPEG files
2. You can use variable options during viewing a
picture.
2. Press HOME and Home Menu appears.
3. Use v V b B to select an option.
a
3. Select [Photo] then press ENTER.
The PHOTO menu appears on the TV screen.
Note:
When the USB Flash Drive is connected and a
disc is inserted simultaneously, the menu for
selecting a media will appear. Select a media
then press ENTER.
b
c
d
e
f
g
a Use b/B to advance to the previous or next
file.
b Use ENTER to start or pause the slide show.
c Use ENTER to play or pause the background
music. This option is available after the background music is selected using [Music Select]
option.
d Use ENTER to rotate the picture clockwise.
This option is not available during slide show.
4. Use v V b B to select a file and press ENTER.
The selected image is displayed in full screen.
e Use ENTER to set the Slide Show speed.
f Selects the background music.
1) Press ENTER and the menu will appear.
2) Use v V b B to select a media or folder
that there are music file(s).
3) Press ENTER to confirm your selection.
g Press ENTER to exit the option menu.
To appear the menu again, press ENTER.
5. To stop viewing at any time, press STOP (x).
The PHOTO menu appears.
Tips:
• You can advance to the previous or next file by
pressing . or > during viewing a photo file
in full screen.
File extensions: “.jpg”, “.jpeg”, “.png”
•
CD-R, DVD±R/RW/RAM, BD-R/RE Format:
ISO 9660+JOLIET, UDF and UDF Bridge format.
•
30
Photo file requirement
You can start the slide show by pressing
N (PLAY) while the PHOTO menu appears.
Select a folder then press ENTER and you can
view the files in the folder. If you want to move to
the upper directory, use v/V to highlight
[UP Folder] and press ENTER.
•
On the PHOTO menu, use red or blue color button to move to the previous or next page.
•
If there is impossible code to express in the file
name, it may be displayed as illegible.
Recommended size:
Less than 3,000 x 3,000 x 24 bit/pixel
Less than 3,000 x 2,250 x 32 bit/pixel
Maximum Files/Disc:
Less than 1999 (total number of files and folders)
Notes on JPEG file
Progressive and lossless compression JPEG
image files are not supported.
Depending on the size and number of the JPEG
files, it may take several minutes to read the
contents of the media.
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 31
To program the remote to control
the TV using the manufacturer code
Reference
Controlling a TV with the
Supplied Universal Remote
Control
You can control the volume, input source, and power
state of your TV with the supplied Universal Remote
Control.
If your TV is listed in the table on pages 32-33, set
the appropriate manufacturer code. Follow steps 1-2
as shown right.
You can control your TV using the buttons below.
If your TV is listed in the table on the next page, set
the appropriate manufacturer code.
1. While holding down TV POWER button, press
the number buttons to select the manufacturer
code for your TV (Refer to table on the next
page).
• If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
2. Release TV POWER button.
Notes:
• Depending on your TV, some or all buttons may
not function on the TV, even after entering the
correct manufacturer code.
TV POWER
Button
TV Control
Buttons
Number
Buttons
By pressing
You can
TV POWER
AV
Turn the TV on or off.
Switch the TV’s input source
between the TV and other input
sources.
PR +/–
Scan up or down through
memorized channels.
VOL +/–
Adjust the volume of the TV.
MUTE
Temporarily turns TV sound
OFF, press again to restore.
•
If you enter a new code number, the code number previously entered will be erased.
•
When you replace the batteries of the remote,
the code number you have set may be reset to
the default setting. Set the appropriate code
number again.
Reference
Note:
Depending on the unit being connected, you may
not be able to control your TV using some of the
buttons.
31
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 32
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with
your TV.
BRANDS
ADMIRAL
ADYSON
AKAI
AKURA
ALBA
ALLSTAR
AMSTRAD
AMWAY
ANITECH
ANTECNO
ARC EN CIEL
ASA
ASBERG
ASORA
ATLANTIC
AUDIOSONIC
AUTOVOX
BANK
BEKO
BESTAR
BLAUPUNKT
BONDSTEC
BOSCH
BRANDT
ELECTRONIQUE
BRIONVEGA
BSR
BUSH
CENTURY
CGE
CIE
CLATRONIC
CLARIVOX
CONDOR
CONIC
CONTEC
CONTINENTAL
EDISON
COSMOS
CROSLEY
CROWN
CODES
137 204
159 219
009 010 108 132
133 135 139 140
156 174 175
064 086 108 110
155 171
009 060 064
108
006 025 157
108
010 049 108 185
219
064
173 179 239
087 102 108 235
236
185
171
089 197
085
159 163 197
232
045 085 086 108
250
086
031 091 092 096
097 098 099 210
253
163
210
173 179 225 239
204
144
009 136 139 144
232
165 204
139 165 210
025 108 170
009 010 064 108
144 149 159 164
165 171 185
033
108 149 191
219
171 222
173 179 225 239
108
165
084
144
CS-ELECTRONICS 064
DAEWOO
051
170
DANSAI
010
DE GRAAF
108
DECCA
070
162
206
DECCAVIDEO
108
DUAL
233
DUMONT
204
32
204
085 086 108
171 185
108 120 127
219
134
108 159 161
184 189 190
BRANDS
ELBE
CODES
058 144 157 160
192 246
ELBIT
108 248
ELECTROVENDA 108
ELEKTRONIKA
108
ELIN
108
ELITE
064 149
ELMAN
144
ELTA
010 171
EMERSON
108 204
ESC
108
ETRON
133
EUROPHON
144 159
EXPERT
089
FENNER
171
FERGUSON
078 079 080 160
182 195 198 199
200 201 202
FINLANDIA
194 195
FINLUX
008 087 102 104
105 107 108 140
144 159 161 174
189 235 236
FIRST-LINE
144
FISHER
086 208 222 233
FORMENTI
108 149
FRABA
108
FRONTECH
136 171 220
FUBA
073 109
FUJITSU GENERAL 088 159 197
FUNAI
010
GALAXIS
108 185
GALERIA
171
GBC
137 144 171
GEC
011 108 129 147
159 189
GELOSO
064 137 144 164
171
GENERAL
171
GENERAL TECHNIC 171
GOLDHAND
159 171
GOLDSTAR
038 050 108 110
136 144 159 163
166 171 191 219
237
GOODMANS
009 064 108 109
110 120 159 170
171
GORENJE
086
GPM
010 064
GRANADA
027 105 108 111
121 134 140 159
162 167 187 194
195 238
GRUNDIG
091 092 093 094
095 097 098 100
101 172 232 238
HCM
010 108 159 171
HIFIVOX
173 179 239
HINARI
010 064 108 133
171
HIT
204
BRANDS
HITACHI
CODES
011 013 015 017
021 022 023 024
028 029 030 035
039 040 041 048
053 054 055 056
057 120 127 128
129 134 135 140
143 145 147 151
156 159 173 193
219
HYPER
009 159 163 171
ICE
009 010 064 108
171
IMPERIAL
043 049 108 139
144 154 165 255
INGERSOLL
171
INNO HIT
159 189 237
INTERBUY
010
INTERCORD
233
INTERFUNK
108 109 113 130
133 134 135 137
141 146 147 148
165 179 210
INTERVISION
010 086 108 132
144 166
IRRADIO
163 235 237
ITC
144 159
ITS
009 010 064 171
ITT
141 151 186
JVC
009 169
KAIDO
136
KAPSCH
089 147 148 197
KARCHER
084 108
KATHREIN
109
KAWA
009
KENDO
060 108 137 157
KENNEDY
197
KNEISSEL
108
KONKA
009
KORTING
086 204 209
KUBA
233
KUBA ELECTRONIC 233
KURA
134
LENCO
108 170
LG
001(Default) 038
050 108 110 136
144 159 163 166
171 191 219 237
LIESENKOTTER
108 210
LIFETEC
010 064 108 170
LOEWE
109 113 204 205
LOGIK
070 227
LUMA
137 197
LUXOR
102 104 132 133
134 135 138 140
143 145 153 156
174 186 237
M ELECTRONIC
103 104
MAGNADYNE
163 164 204
MAGNAFON
199
MAGNASONIC
108
MARANTZ
108
MARSHAL
064
MATSUI
009 016 025 060
061 062 063 070
108 131 136 152
154 159 171 172
BRANDS
MERRIT
METZ
5/2/08
11:05 AM
CODES
132
047 092 097 098
100 101 108 204
207 254
MITSUBISHI
075 076 077 097
113 204 222 224
240
MIVAR
044 042 159 235
MNARTT
007
MTC
086 109 134
MULTITECH
136 159 171 185
MURPHY
232
NAONIS
137
NECKERMANN
037 059 060 092
098 100 101 108
109 113 115 118
119 134 135 137
143 157 159
NEI
064 108
NIKKAI
219
NIKKO
108
NOBLIKO
232 235
NOGAMATIC
173 179 239
NOKIA
014 019 032 102
103 104 108 132
133 134 135 138
140 141 145 146
147 148 156 174
NORDMENDE
129 173 179 180
181 193 195 225
226 228 239
NORMN
108
NOVA
087
OCEANIC
032 103 104 135
140 156
OKANO
108
ONWA
009 010 064
ORAVA
108
ORBITER
086
ORION
025 059 060 061
062 064 070 108
110 118 219
OSAKE
106
OTTO-VERSAND 002 005 009 014
059 060 081 082
083 085 092 097
098 100 101 108
109 111 113
PAEL
235
PANASONIC
002 003 005 167
168 229
PATHE CINEMA
144
PATHE MARCONI 173 179 225 239
PHILCO
090 108 139 144
148 165 204
PHILIPS
065 066 067 068
069 092 108 109
111 112 114 115
116 119 122 123
124 125 193 212
251 252
PIONEER
193
PRANDONI-PRINCE 137 235
PRIMA
219
PRO VISION
108
Page 33
BRANDS
PROFEX
PROFITRONIC
QUELLE
RADIOLA
RADIOTONE
REDIFUSSION
REVOX
REX
RFT
RITAR
ROADSTAR
ROSITA
SABA
SAISHO
SAKIO
SALORA
SAMBERS
SAMSUNG
SANY
SANYO
SCHNEIDER
SEG
SEI-SINUDYNE
SELECO
SENTRA
SHARP
SHINTOM
SHINTOSHI
SHIVAKI
SIAREM
SIEMENS
SIESTA
SILVER
SINGER
SINUDYNE
SMARAGO
SOLAVOX
SONOLOR
SONTEC
SONY
CODES
108 136 171
108
002 010 014 019
025 059 060 072
084 086 087 088
092 097 098 100
101 102 175
108
010 085 108 171
187
109
088 089 137 157
158 164 197 246
247
064 085 135 204
138
108
171
079 146 147 173
179 181 193 195
225 226 239
025 060 070 136
159
171
019 032 103 104
132 133 134 135
137 138 140 142
143 145 150 156
174 237 241
235
004 010 050 086
108 117 126 171
220 237
193
014 018 019 020
032 034 071 086
087 189 218 221
222 223
009 064 088 108
133 141 159 163
233
010 064 108 144
159 165 171 185
219
025 108 204 212
088 089 137 157
197 222
064 133
081 082 083 222
108
108
108
204
092 096 097 098
100 101 108 210
218 219 221
085
010 064
108 164 204
118 131
172
133
140 156
108
072 074 211 212
213 214 215 216
217 222
BRANDS
SPECTRA
STARLITE
STARLUX
STERN
CODES
170
108 171
171
088 089 137 157
197
SUNSTAR
108 171
SUPERTECH
108 139 152 171
TADISTAR
108
TASHIKO
108 159 218
TEC
108 139 144 159
170 171
TECHLINE
185
TECHNISAT
108 165
TECNISON
108 171
TEKON
171
TELEAVIA
173 178 179 225
239
TELEFUNKEN
079 177 179 181
193 195 200 210
TELEOPTA
171
TELERNT
109
TELETECH
165 171
TELETEXT
115
TELETON
088
TELETON
089 134 159 197
TENSAI
064 108 144 149
171 191
TENSON
171
TESLA
204
THOMSON
052 078 079 134
173 178 179 181
193 195 225 239
THORN
011 014 016 018
026 028 066 072
075 087 097 102
108 116 135 141
145 146 160
THORN-FERGUSON 160 188 200 227
TOSHIBA
012 016 026 036
037 222 232
TOWADA
144 185
TRISTAR
010 064
TRIUMPH
025 219 236
UHER 089
108 109 149 185
197 233
ULTRAVOX
108 164 185 204
UNIVERSUM
174
UNIVOX
204
VESTEL
108
VIDEOSAT
165
VIDEOTON
178 193
VIDEOWAY
230
VISION
108 149
VOXSON
137 204
WALTHAM
178
WATSON
064 108 149 171
WEGA
208 222
WHITE
108 110 149
WESTINGHOUSE
YOKO
010 064 108 136
144 159 164 170
171
ZANUSSI
137 197
ZENITH
231
Reference
BH200-P-ASGPLLK-ENG
33
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 34
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Code
6566
6565
6570
8381
6577
6582
7289
6583
6589
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Area Codes
Choose an Area code from this list.
Area
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
34
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
Area
Code
Ethiopia
ET
Fiji
FJ
Finland
FI
France
FR
Germany
DE
Great Britain
GB
Greece
GR
Greenland
GL
Herd and Mcdonald Islands HM
Hong Kong
HK
Hungary
HU
India
IN
Indonesia
ID
Israel
IL
Italy
IT
Jamaica
JM
Japan
JP
Kenya
KE
Kuwait
KW
Libya
LY
Luxembourg
LU
Area
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation
Code
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
PY
PH
PL
PT
RO
RU
Area
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 35
Troubleshooting
Correction
Possible Cause
Symptom
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet securely.
The power is on, but
the player does not
work.
• No disc is inserted.
• Insert a disc. (Check the disc indicator in the display window is lit.)
No picture.
• The TV is not set to receive DVD signal output.
• Select the appropriate video input
mode on the TV.
• The video cable is not connected
securely.
• Connect the video cable securely.
• The selected resolution is not capable with your TV.
• Select another resolution using
RESOLUTION button.
• The equipment connected with the
audio cable is not set to receive disc
signal output.
• Select the correct input mode of the
audio receiver so you can listen to
the sound from the player.
• The power of the equipment connected with the audio cable is turned off.
• Turn on the equipment connected
with the audio cable.
• The [AUDIO] options are set to the
wrong position.
• Set the [AUDIO] options to the correct position. (See page 21)
• An unplayable disc is inserted.
• Insert a playable disc. (Check the
disc type and regional code.)
• The rating level is set.
• Change the rating level.
No sound.
The player does not
start playback.
• The Remote Control is not pointed at
The Remote Control
the remote sensor on the player.
does not work properly.
• The Remote Control is too far from
the player.
Resetting the Player
If you observe any of the following symptoms...
When the Player is plugged in, but the power will
not turn on or off.
When the display window is not working.
When the Player does not operate normally.
• Point the Remote Control at the
remote sensor of the player.
• Operate the Remote Control closer to
the player.
You can reset the Player as follows:
Press and hold the POWER button for more
than five seconds. This will force the Player to
power off. Press the POWER button again to
turn the Player back on.
Unplug the power cord and then plug the power
cord again after more than five seconds.
You can update the Player using the latest software to enhance the products operation and/or add new features.
To obtain the latest software for this player (if updates have been made), please visit http://sg.lgservice.com or
contact LG Electronics customer care center.
Reference
Customer Support
35
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 36
Specifications
General
Power requirements:
AC 110-240V, 50/60Hz
Power consumption:
25W
Dimensions (W x H x D):
Approx. 16.9 x 3.0 x 10.6 mm (430 x 77 x 269 inches)
Net Weight (Approx.):
3.8 kg (8.3 lbs)
Operating temperature:
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity:
5 % to 90 %
Outputs
VIDEO OUT:
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
COMPONENT VIDEO OUT:
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
HDMI OUT (video/audio):
19 pin (HDMI standard, Type A)
ANALOG AUDIO OUT:
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL OUT (OPTICAL):
3 V (p-p), Optical jack x 1
System
Laser:
Semiconductor laser, wavelength: 405nm / 650 nm
Signal system:
Standard PAL/NTSC Colour TV system
Frequency response:
20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Signal-to-noise ratio:
More than 100 dB (ANALOG OUT connectors only)
Harmonic distortion:
Less than 0.008%
Dynamic range:
More than 95 dB
LAN port:
Ethernet jack x 1, 10BASE-T/100BASE-TX
Accessories:
HDMI cable (1)
Component video cable (1)
Video cable (1)
Audio cable (1)
Remote control (1)
Batteries (2)
Cloth for cleaning the surfaces of the player (1)
Note: Design and specifications are subject to change without prior notice.
36
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 37
The unit’s Audio Output Specifications
Jack/
Setting
SPDIF (DIGITAL AUDIO OUT) *5
Analog
Output
Stereo
PCM
Stereo
DTS
Re-encode *3 *6
Primary
Pass-Thru *1
Dolby Digital
PCM 2ch
PCM 2ch
DTS
Dolby Digital
Dolby Digital Plus
PCM 2ch
PCM 2ch
DTS
Dolby Digital
Dolby TrueHD
PCM 2ch
PCM 2ch
DTS
PCM 2ch
Source Format
DTS
PCM 2ch
PCM 2ch
DTS
DTS
DTS-HD
PCM 2ch
PCM 2ch
DTS
DTS
Linear PCM 2ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
Linear PCM 5.1ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
Linear PCM 7.1ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
MPEG
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
Jack/
Setting
HDMI OUT
Primary Pass-Thru *1, *2
HDMI 1.2
HDMI 1.3
PCM
Stereo
PCM
Multi-Ch *3
DTS
Re-encode *6
Dolby Digital
PCM 2ch
PCM 5.1ch
DTS
Dolby Digital
Dolby Digital
Dolby Digital Plus
PCM 2ch
PCM 5.1ch
DTS
Dolby Digital
Dolby Digital
Dolby TrueHD
PCM 2ch
PCM 2ch
DTS
PCM 2ch
PCM 2ch
DTS
Source Format
DTS
PCM 2ch
PCM 5.1ch
DTS
DTS
DTS-HD
PCM 2ch
PCM 5.1ch
DTS
DTS
DTS
Linear PCM 2ch
PCM 2ch
PCM 2ch
DTS
PCM 2ch
PCM 2ch
Linear PCM 5.1ch
PCM 2ch
PCM 5.1ch
DTS
PCM 5.1ch
PCM 5.1ch
Linear PCM 7.1ch
PCM 2ch
PCM 7.1ch
DTS
PCM 7.1ch *4
PCM 7.1ch *4
MPEG
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
Notes:
*1 The secondary and interactive audios may not be included in the output bitstream if [SPDIF] or [HDMI]
option is set to [Primary Pass-Thru].
*2 This player automatically selects the HDMI audio according to the decoding capability of the connected
HDMI device if [HDMI] option is set to [Primary Pass-Thru].
*4 The Linear PCM 5.1ch/7.1ch audio source recorded at 192 kHz sampling frequency will output as PCM
stereo audio.
*5 The sampling frequency of HDMI/SPDIF (DIGITAL AUDIO OUT) is limited to 96 kHz.
*6 The audio is limited to 48 kHz and 5.1 ch if [HDMI] or [SPDIF] option is set to [DTS re-encode].
The DTS audio will output on BD and HD DVD advanced disc, and the original audio will output on the
other discs.
Reference
*3 The [PCM Multi-CH]/[Primary Pass-Thru] setting of the [HDMI] option and [DTS re-encode] setting of the
[SPDIF] option cannot be set together. If you set the [HDMI] option to [PCM Multi-CH] or
[Primary Pass-Thru], the [SPDIF] option is set to [PCM Stereo] automatically. Also, if you set the [SPDIF]
option to [DTS Re-encode] and the [HDMI] option is set to [PCM Stereo] automatically.
(The Linear PCM audio source may output as PCM stereo audio from DIGITAL AUDIO OUT jack if the
[HDMI] option is set to [Primary Pass-Thru] or the [SPDIF] option is set to [DTS Re-encode].)
• The audio is always output as PCM 48kHz/16 bit during Audio CD or MP3/WMA file is playing back.
• The MPEG audio source is always output as PCM 2ch.
37
BH200-P-ASGPLLK-ENG
5/2/08
11:05 AM
Page 38
Open source software notice
The following GPL executables and LGPL/MPL libraries used in this product are subject to the
GPL2.0/LGPL2.1/MPL1.1 License Agreements:
GPL EXECUTABLES:
Linux kernel 2.6, bash, busybox, sysutils, net-tools, dhcpcd, tinylogin, mtd-utils
LGPL LIBRARIES:
uClibc, DirectFB, GnuTLS, iconv, cairo
MPL:
Mozilla 1.0
LG Electronics offers to provide source code to you on CD-ROM for a charge covering the cost of performing
such distribution, such as the cost of media, shipping and handling upon e-mail request to LG Electronics at:
opensource@lge.com
This offer is valid for a period of three(3) years from the date of the distribution of this product by LG
Electronics.
You can obtain a copy of the GPL, LGPL licenses from http://www.gnu.org/licenses/
and a copy of MPL license from http://www.mozilla.org/MPL/
This software is based in part on the work of the Independent JPEG Group copyright © 1991-1998,
Thomas G. Lane.
This product includes
• Freetype library : Copyright © 2003 The FreeType Project (www.freetype.org).
• libpng library : Copyright © 2004 Glenn Randers-Pehrson
• Zlib compression library: Copyright © 1995-2002 Jean-loup Gailly and Mark Adler
• cryptographic software written by Eric Young (eay@cryptsoft.com).
• software written by Tim Hudson (tjh@cryptsoft.com).
• software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org)
This product includes other open source software.
• Copyright © David L. Mills 1992-2006
• Copyright © 1998-2003 Daniel Veillard.
• Copyright © 1998, 1999 Thai Open Source Software Center Ltd.
• Copyright © 1990 The Regents of the University of California.
• Copyright © 1998-2005 The OpenSSL Project.
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software without restriction, including without limitation
the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and
to permit persons to whom the Software is furnished to do so, subject to the following conditions:
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF
CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
38
BH200-P-ASGPLLK-ENG
5/2/08
P/NO : MFL36364151
11:05 AM
Page 39
Download PDF

advertising