LG | WD-1250ERD | LG WD-1250ERD Owner’s Manual

P/No.: MFL30138469
Washing Machine
OWNER’S MANUAL
WD-1250ERD
WD-12500RD
WD-12505RD
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner’s manual carefully, it provides
instructions on safe installation, use and maintenance.
Retain it for future reference.
Record the model and serial numbers of your washing machine.
P
추가선택, 예약,
C
roduct Feature
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
belt and pulley.
Water Circulation
Sprays detergent solution and water onto the load over and over.
Clothes are soaked more quickly and thoroughly during wash cycle.
The detergent suds can be removed more easily by the water shower during rinse
cycle. The water circulation system uses both water and detergent more efficiently.
Tilted Drum and Extra Large Door Opening
Tilted drum and extra large opening make it possible to load
and unload clothing more easily.
Steam Washing and Refresh
Steam Washing features upgraded washing performance with low energy and
water consumption. Refresh cycle removes wrinkles from dry clothes.
RollerJets
Washing ball enhances the wash performance and reduces damage
to the clothing. The jets spray and help tumble clothes to enhance
washing performance while maintaining fabric care.
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
Built-in Heater
Internal heater helps to maintain water temperature at its optimum level for selected
cycles.
Child Lock
The Child lock prevents children from pressing any button to change the settings
during operation.
ontents
Warnings ......................................................................................................................3
Specification...................................................................................................................5
Installation......................................................................................................................6
Care before washing....................................................................................................12
Adding detergent..........................................................................................................13
Function
....................................................................................................................15
How to use washer ......................................................................................................16
Maintenance ................................................................................................................26
Troubleshooting guide .................................................................................................30
Terms of Warranty .......................................................................................................34
2
W arnings
READ ALL INSTRUCTIONS BEFORE USE
!
WARNING!
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using
the washer, follow basic precautions, including the following:
• Do not install or store the washer where it will
be exposed to the weather.
• Do not tamper with controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically
recommended in the user-maintenance
instructions or published user-repair instructions
that you understand and have the skills to carry
out.
• Keep the area underneath and around your
appliances free of combustible materials such as
lint, paper, rags, chemicals, etc.
• Close supervision is necessary if this appliance
is used by or near children or infirm persons.
Do not allow them to play on, with, or inside this
or any other appliance.
• Keep washer away from fire.
• Do not leave the washer door open.
An open door could entice children to hang on
the door or crawl inside the washer.
• Never reach into washer while it is moving. Wait
until the drum has completely stopped.
• The laundry process can reduce the flame
retardant of fabrics.
• Do not wash or dry articles that have been
cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as
wax, oil, paint, gasoline, degreasers, dry
cleaning solvents, kerosene, etc.) which may
ignite or explode. Oil may remain in the tub after
a whole cycle resulting in fire during drying. So,
do not load oiled clothes.
• Always follow the fabric care instructions
supplied by the garment manufacturer.
• Do not slam the washer door closed or try to
force the door open when locked. This could
result in damage to the washer.
• To minimize the possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
• Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
• Dryer is intended for only drying textile material.
• If the washer has been exposed to water, call an
authorized service provider to avoid any risk of
fire or electric shock.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
• Do not use an adapter or otherwise defeat the grounding plug.
• If you don’t have the proper outlet, consult an electrician.
WARNING
:
Improper connection of the equipment-grounding conductor can result in risk of electric
shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
3
W arnings
To minimize the risk of fire in a tumble dryer, the following should be observed:
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire
hazard and should not be placed in a tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat
sources Such as in a tumble dryer. The items become warm, causing an oxidation
reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can
become hot enough to catch fire. Piling, stacking or storing oil-affected items can
prevent heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been
contaminated by hair care products be placed in a tumble dryer they should first be
washed in hot water with extra detergent-this will reduce, but not eliminate, the
hazard. Washed in hot water with extra detergent-this will reduce, but not
eliminate, the hazard.
• Items that have been previously cleaned in, washed in, soaked in or spotted with
petrol/gasoline, dry-cleaning solvents or other flammable or explosive substances
should not be placed in a tumble dryer.
Highly flammable substances commonly used in domestic environments include
acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some
brands), turpentine, waxes and was removers.
• Items containing foam rubber (also known as latex foam) or similarly testured
rubber. like materials should not be dried in a tumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
• Fabric softeners or similar products should not be used in a tumble dryer to eliminate
the effects of static electricity unless this practice is specifically recommended by the
manufacturer of the fabric softener or product.
• Undergarments that contain metal reinforcements should not be placed in a tumble
dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during
drying. When available a drying rack could be used for such items.
• Plastic articles such as shower caps or babies waterproof napkin covers should not
be placed in a tumble dryer.
• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, galoshes and
rubber-coated tennis shoes should not be placed in a tumble dryer.
4
S
pecification
Inlet Hose
DOOR LOCK
20%
EST. TIME G
REMAININ
shing1200rpm
Wa
_ _ _ Normal
Name
Power supply
Size
Weight
Wash capacity
Dry capacity
Max. Watt
Spin speed
Water consumption
Permissible water pressure
1:12
60°C
: Front loading washing machine
: 220-240V~, 50Hz
: 635mm(W) x 720mm(D) x 925(H)
: 80kg
: 11kg(2200W)
: 6kg(2200W)
: 2200W
: No Spin/400/800/1000/1200
: 113ℓ (10.3ℓ/kg)
: 0.3 - 10kgf/cm2 (30~1000kPa)
❋ The appearance and specifications may be varied without notice to improve the
units quality.
Accessories
Inlet hose(1EA)
Spanner
5
I
nstallation
Install or store where it will not be exposed to temperatures below freezing or exposed to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other
vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at
all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the
appliance guarantee.
Transit bolts
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be
removed before using the washer.
When unpacking the base, be sure
to remove the additional packing
support in the middle of the base
packing.
Washer
Packing Support
Base Packing
Removing transit bolts
1. To prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts along with the rubber bungs.
3. Take out the 4 bolts along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future use.
• If they are not removed, it may cause heavy
vibration, noise and malfunction.
• Whenever the appliance is transported, the
transit bolts must be refitted.
2. Unscrew the 4 bolts with
the spanner supplied.
4. Close the holes with the caps supplied.
6
I
nstallation
Installation place requirement
Drain Hose
Washer
Laundry
Tub
approx.
2cm
Level floor :
Allowable slope under entire washer is 1°
Power outlet :
Must be within 1.5 meters of either side of location
of washer. Do not overload the outlet with more than
one appliance.
Additional Clearance :
For wall, door and floor modeling is required.
(10cm : rear / 2cm : right & left side)
Do not place or store laundry products on top of
washer at any times.
They can damage the finish or controls.
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
• Before placing the washer on tiles, apply a rubber mat under the feet.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or
similar materials under the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal burning
stove,an insulating(85x60cm) covered with aluminum foil on the side facing the cooker or
stove,must be inserted between the two appliance.
• The washer must not be installed in rooms where the temperature can drop below 0°C.
• Please ensure that when the washer is installed, it is easily accessible for the engineer in
the event of a breakdown.
• With the washer installed adjust all four feet using the transit bolt spanner provided
ensuring the appliance is stable, and a clearance of approximately 20mm is left between
the top of the washer and the underside of the work-top.
7
I
nstallation
Electrical connection
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or
similarly qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
• Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses
may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below
freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing
machine at room temperature for a few hours before putting it into operation.
CAUTION
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
Washing Machine is to be connected to the water mains using new hose-sets and that old
hose-sets should not be used.
Connecting water supply hose
▶Water supply pressure must be between 30kPa and 1000kPa
(0.3~10kgf/cm2)
▶Don’t strip or crossthread when connecting Inlet hose to the valve.
▶If the water supply pressure is more than 1MPa, a decompression
device should be installed.
• Two rubber seals are supplied with the water inlet hoses these
are in order to prevent water leaks.
• Check water tightness of washing machine connections by
turning the tap completely on.
• Periodically check the condition of the hose and replace the
hose if necessary.
• Make sure that there is no kink on the hose and that it is not
crushed.
▶When your washer has two valves,
• The Inlet hose which has red connector is for the hot water tap.
• If the washer has two valves, the energy is saved by using hot
valve.
8
I
nstallation
Normal Tap without thread & screw type inlet hose
1. Unscrew the fixing screw to
attach the tap.
2. Push the connector up till the
rubber packing is in tight contact
with the tap. Then tighten the 4
screws.
3. Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
Normal Tap without thread & one touch type inlet hose
1. Un tighten the upper connector 2. Push the upper connector up till 3. Connect the water supply hose
screw.
Upper
Connector
Fixing screw
Rubber
packing
Middle
connector
• In case the diameter of the tap is
large remove the guide plate.
Guide plate
the rubber packing is in tight
contact with the tap. Then
tighten the 4 screws.
Upper
Connector
Rubber packing
Plate
Upper
Connector
Water supply
hose
Middle
connector
• Turn the middle connector not
to have water leaked.
Connector
to the middle connector,
pushing the plate down.
• Make sure that the rubber seal
is inside the hose connector.
• To separate the water supply
hose from the middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate down.
Hose connector
Rubber seal
Used the horizontal tap
Horizontal tap
Extension tap
• Your machine comes with only
cold water connection.
• Make sure that there are no
kinks in the hose and that it is
not crushed.
Square tap
9
nstallation
I
This equipment is not designed for maritime use or for use mobile installations such as
caravans, aircraft etc.
Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the Plug.
Disable the door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation ! Keep all packaging well away from children
Installation of drain hose
about 100 cm
min. 60 cm
max. 100 cm
about 145 cm
• When installing the drain hose to a sink,
secure it tightly with a string.
• Proper securing of the drain hose will
protect the floor from damage due to
water leakage should the drain hose
become loose.
about 105 cm
Laundry tub
about 100 cm
Hose
Retainer
max. 100 cm
about 105 cm
min. 60 cm
about 145 cm
• The drain hose end should not be placed higher
than 100 cm above the floor.
• Proper securing of the drain hose will protect the
floor from damage due to water leakage.
• When the drain hose is too long, do not force
back into the washer. This will cause abnormal
noise, malfunction, and water leakage.
10
max. 100cm
min. 60cm
Tie
strap
max. 100cm
min. 60cm
I
nstallation
Level adjustment
1. Adjusting the washing machine level properly prevents excessive
noise and vibration.
Install the appliance on a solid and level floor surface, preferably in
a corner of the room.
NOTE
Timber or suspended type flooring may contribute to
excessive vibration and unblance errors.
2. If the floor is uneven, adjust the adjustable feet as required. (do
not insert pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use a spirit level)
※ After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
NOTE
In the case that the washing machine is installed on a raised
platform, it must be securely fastened in order
to eliminate the risk that it might fall off.
❊ Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the
machine should not move up and down at all. (Please, check both of two directions)
If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
Concrete floors
• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.
Tile floors (Slippery floors)
• Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm
sections and stick the pieces on to the dry tile where machine is to be placed.)
※ Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.
Wooden floors (Suspended floors)
Rubber Cup
• Wooden floors are particularly susceptible to vibration.
• To prevent vibration we recommend you place rubber cups under each foot,
at least 15mm thick under the washer, secured to at least 2 floor beams with
※ It can be purchased from
hardware suppliers.
screws.
• If possible install the washer in one of the corners of the room, where the floor is more stable.
※ Insert the rubber cups to reduce vibration.
※ Rubber cups ( p/no. 4620ER4002B ) can be purchased from the LG spare parts department.
Important!
• Proper placement and levelling of the washer ensures long, regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
11
C
are before washing
Before the first washing
Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash
without clothing. This will remove residues and water from the drum that may have been left
during manufacturing.
Caring before washing
1. Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and
how it should be washed.
2. Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can
occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly
soiled one.
Soil (Heavy, Normal, Light)
Separate clothes according to amount of soil.
Color (White, Lights, Darks)
Separate white fabrics from colored fabrics.
Lint (Lint producers, Collectors)
Wash lint producers and lint collectors
separately.
3. Caring before loading
Combine large and small items in a load. Load large items first. Large items should not be more than half
the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
• Check all pockets to make sure that they
are empty. Items such as nails, hair clip,
matches, pens, coins and keys can damage
both your washer and your clothes.
• Close zippers, hooks and strings to
make sure that these items don’t
snag on other clothes.
• Pre treat dirt and stains by brushing a little
detergent dissolved in water onto stains like
collars and cuffs to help shift dirt.
• Check the folds of the flexible gasket (gray) and
remove any small articles,if any.
• Check inside of the drum and remove any left
items in it for next wash cycle.
• Remove any clothing or items on the flexible
gasket to prevent clothing and the gasket
damages.
12
A dding detergent
Adding detergent and fabric softener
1. The Dispenser Drawer
• Main wash only ➔
• Pre Wash + Main Wash ➔
(
(
)
()
)
2. Adding Fabric Softener
(
)
• Do not exceed the maximum fill line.
Close the dispenser drawer slowly.
Overfilling can cause early dispensing
of the fabric softener which could stain
clothes.
• Do not leave the fabric softener in the
detergent drawer for more than 2 days.
(Fabric softener could harden)
• Softener will automatically be added
during the last rinse cycle.
• Do not open the drawer when water is
supplied.
• Solvents(benzene, etc) are not
allowable.
NOTE
Do not pour fabric softener
directly on the cloths
13
A dding detergent
3. Detergent dosage
• The detergent should be used according to the
instruction of the detergent manufacture.
• If too much detergent is used, too many suds
can occur and this will decrease the washing
result or cause heavy load to the motor.
• Use powder detergent only for the front
loading washer.
❇ If suds occur too much, pleas reduce the
detergent amount.
• Detergent usage may need to be adjusted
for water temperature, water hardness,
size and soil level of the load. For best
results, avoid oversudsing.
❋ Tips
Full load : according to
manufacturer’s recommendation.
Part load : 3/4 of the normal
amount.
Minimum load : 1/2 of full load.
• Detergent is flushed from the dispenser
at the beginning of the cycle.
5. Using the Tablets
1) Open the door and Tablets into the
drum.
4. Water softener
2) Load the laundry into the drum.
• A water softener, such as Anti limescale
(Clagon) can be used to cut down on the
use of detergent in extremely hard water
areas. Dispense according to the amount
specified on the packaging.
First add detergent and then the water
softener.
• Use the quantity of detergent as for soft
water.
14
3) Close the door.
F
unction
Recommended courses according to the laundry type
Program
Cotton
Synthetic
Fabric Type
Color fast garments
(shirts, night dresses,
pajamas...)and lightly soiled white
cotton (underwear...)
60˚C
(Cold,
30˚C, 40˚C,
95˚C)
Polyamide, Acrylic,
Polyester.
40˚C (Cold,
30˚C, 60˚C)
Baby Care Lightly soiled baby wear
For clean wash through
Allergy Care eliminate allergy source.
Refresh
Cotton mixed, Polyeter mixed
Dress shirts, blouses (It just makes
wrinkled clothes easy to iron)
Delicate
Delicate laundry easily
damaged.
Hand Wash “Hand Wash” marked laundry
or machine washable woolens.
/Wool
Quick 30
Cotton
Quick
Proper
Temp.
(Option)
Additional
Option
Maximum
Load
- Pre Wash
- Rinse+Spin
- Less Steam
- Eco Steam
- Turbo Steam
- Intensive
Rating
60°C
40°C, 95°C)
5.0kg
6.0kg
–
- Turbo Steam
- Intensive
5.0kg
–
- Turbo Steam
5 items
40˚C
(Cold, 30˚C)
30°C
(Cold,40˚C)
Colored Landry which is
lightely soiled fast.
30˚C
(Cold, 40˚C)
Cotton Which is lightly
soiled.
40˚C
(Cold, 30˚C)
4.0kg
- Rinse+Spin
- Intensive
3.0kg
- Rinse+Spin
- Intensive
- Pre Wash
- Rinse+Spin
- Less Steam
- Eco Steam
- Turbo Steam
- Intensive
5.0kg
Rating
❋ Water Temperature : Select the water temperature to the wash cycles.
Always follow garment manufacture’s care label or instructions
when laundering.
❋ Intensive : When washing full load or heavily soiled laundry, you can increase
effectiveness by choosing intensive option.
❋ Pre Wash : If the laundry is heavily soiled, “Pre Wash” option is recommended.
Pre Wash is available in Cotton, Synthetic , Cotton Quick and Baby Care
Program.
15
H ow to use washer
20%
Time Left
1:12
Washing
___
1. Cotton automatically
selected upon power on.
• Press the Power(
) button to start.
• Press the Start/Pause(
• Initial condition
- Rinse : 3 times
- Water temperature : 60°C
- Spin : 1200 rpm
- Program : Cotton
) button.
Normal
1200rpm
60°C
2. Manual Selecting
• Press the Power(
washer on.
) button to turn the
• Select the desired cycle with the
program dial and if required, make any
changes to the washing conditions by
pressing the buttons accordingly.
For selecting the each conditions, please
refer to the page17~page25
• Press the Start/Pause button to
commence the cycle.
3. Language Selection
• English is the default language.
Language can be changed only when
LCD is on. Power On and then press
the Time delay and Intensive button
simultaneously for 3 seconds until the
Select a Language menu is displayed.
Select a Language
English
Spanish
Portuguese
• Rotation of the program dial will cycle
through Spanish, Portuguese and then
back to English.
16
H ow to use washer
Cotton Quick
Synthetic
Cotton
Delicate
20%
Time Left
1:12
Washing
Hand Wash
W
/Wool
___
Normal
1200rpm
60°C
Quick 30
(1)
(2)
(1)Button: Power
(2)Dial: Program
(3)Button: Start/Pause
(3)
(4)Button: Option
(5)Child lock
(6)Button: Rinse
Power
(4)
(5)
(6) (7)
(7)Button: Spin
(8)Tub Clean
(9)Button: Temp.
(8) (9)
(10) (11)
(12) (13)
(10)Button: Time Delay
(11)Button: Intensive
(12)Button: Turbo Steam
(13)Dial: Dry
Program
1. Power
• Press the Power(
power on and off.
) button to turn
• To cancel the Time Delay function, the
Power( ) button must be pressed.
• 9 programs are available according to the
laundry type.
2. Initial Program
• Dial lamp will light up to indicate selected
program.
• When the Power( ) button is pressed,
the washer is ready for Cotton program.
And the other initial conditions as follows.
• So, if you want to advance into the
washing cycle without changing the
program, just press Start/Pause( )
button and then the washer will proceed.
■ Initial program
- Cotton Program / Rinse:Normal / 60°C/
1200rpm
• When Start/Pause( ) button is pressed,
the Cotton program is automatically
selected.
- By turning the Program dial, the program is
selected in order of “Cotton – Cotton Quick
– Synthetic – Delicate – Hand Wash/Wool
– Quick 30 – Refresh – Allergy Care –
Baby Care”.
For information regarding laundry type for
each program, please refer to page 15.
17
H ow to use washer
Option
Start/Pause
Pre Wash
Rinse + Spin
Less Steam
Eco Steam
Less
Steam
1. Start
• This Start/Pause button is used to start
wash cycle or pause the wash cycle.
2. Pause
• If temporary stop of wash cycle is needed,
press “Start/Pause” button.
• When in Pause, the power is turned off
automatically after 4 minutes.
Door Lock
20%
Time Left
Normal
1200rpm
1200rpm
___
• By pressing the option button, only one
option function may be selected.
NOTE:
Depending on the selected program cycle,
not all Options may be selectable.
1. Pre Wash
• Use this option for loads that need
pretreatment. This adds 16 minutes of pre
washing before draining.
- When using Pre Wash option, do not use
a liquid detergent for the main wash.
Use powder for the main wash.
1:12
• Available in Cotton, Synthetic, Baby Care
and Cotton Quick.
60°C
2. Rinse + Spin
Washing
___
Normal
• Lights whenever the door of the washer is
locked.
• The door can be unlocked after a 2~3
minute delay, pressing the Start/Pause
button to stop the washer.
• Use this option to rinse and then spin
3. Less Steam
• When you want to do a steam wash for
only a small amount of laundry, select the
this opton.
4. Eco Steam
• When you want to do a steam wash to
reduce the electricity consumption, select
this opton.
18
H ow to use washer
Rinse
Child lock
Rinse+ + Hold
Normal + Hold
Medic Rinse
Rinse+
Normal
If you choose to lock the buttons on the
control assembly to prevent tampering, this
function may be selected.
• Child lock can be set by pressing and
holding the Option and Rinse button
simultaneously. (About three seconds)
20%
Time Left
1:12
1200rpm
60°C
Normal
Medic
Rinse
1200rpm
___
• By pressing the Rinse button, the Rinse
type can be selected.
- Normal
- Rinse+
- Medic Rinse
- Normal+Hold
- Rinse++Hold
1. Normal
Child lock is on.
___
Less
Steam
• Cotton (for full load), Synthetic, Allergy Care,
Cotton Quick, Baby Care performs 3 Rinses
• To deactivate Child lock system, press
and hold the Option and Rinse button
simultaneously again.
(About three seconds)
20%
Time Left
1:12
1200rpm
60°C
Child lock is off.
___
Normal
• To change to the desired program, whilst in
child lock mode.
1. Press and hold both Option and Rinse
button to cancel the child lock.
(About three seconds)
2. Press the Start/Pause button.
3. Select the desired program and press the
Start/Pause button again.
Change
the desired
program
• The child lock can be set at any time and it
can be deactivated only by using child-lock
cancel process. Turning the power off and
operational errors will not affect child-lock.
• Cotton (for part load), Delicate, Hand
Wash/Wool, Quick 30 performs 2 Rinses.
2. Rinse+ & Medic Rinse
• Used to additional rinse, which may assist
in removing traces of detergent residue.
• By selecting Rinse+ or Medic Rinse
function, the Rinse Time and the Rinse
water are increased.
• Medic Rinse heats the water to 40 Deg in
the last rinse.
3. Rinse Hold
• Is selected by pressing the Rinse button
repeatedly this function leaves clothes in the
washer; suspended in the water after a rinse
without entering into spin.
• To proceed to a Drain or Spin function after
a Rinse hold, press the Spin button for the
desired speed, then press the Start/Pause
button.
The matching indicator lamp will light up for
identification.
19
H ow to use washer
Spin
Water Temperature
1200rpm
1000rpm
800rpm
400rpm
No spin
Less
Steam
Medic
Rinse
400rpm
95°C
60°C
40°C
30°C
Cold
___
___
Normal
1200rpm
40°C
• By pressing the Spin button, the spin
speed can be chosen.
• By pressing the Temp. button, the
water temperature can be selected.
1. Spin selection
- Cold
- 30˚C / 40˚C / 60˚C / 95˚C
• Spin speed is available according to the
program as follows.
- Cotton & Cotton Quick & Quick30
No Spin – 400 – 800 – 1000 – 1200
- Allergy Care & Baby Care & Synthetic
& Hand Wash/Wool
No Spin – 400 – 800 – 1000
- Delicate
No Spin – 400 – 800
2. No spin
• Water temperature can be selected as
below according to the program.
- Cotton
Cold – 30°C – 40°C – 60°C – 95°C
- Synthetic
Cold – 30°C – 40°C – 60°C
- Cotton Quick & Delicate &
Hand Wash/Wool & Quick30
Cold – 30˚C – 40˚C
- Baby Care
40°C – 60°C – 95°C
• If “No Spin” is selected, the washer stops
after draining the water from the last spin.
The required temperature lamp will light up
for identification.
The matching indicator lamp will light up for
identification.
For the more detailed information, please
refer to the page15.
20
H ow to use washer
Detecting
1%
Time Left
Time Delay
___
Time Left
Detecting
___
Normal
1200rpm
60°C
• While the "Detecting" is shown in the
display the machine rotates slowly and
detects how many laundries are loaded in
the drum. It will take a few seconds.
• Available in Cotton, Cotton Quick and
Synthetic program.
Intensive
Time Left
___
Cotton
___
Normal
3:00
To increase the delay wash time
press on the time delay button.
___
Normal 1200rpm 60°C
1200rpm
60°C
Time Left
6:00
To increase the delay wash time
press on the time delay button.
___
Normal 1200rpm 60°C
Preparing washing before starting “Time Delay”
- Turn on the water tap.
- Load laundry and close the door.
- Place the detergent and fabric softener in
the drawer.
• How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select
the program you require.
- Press Time Delay button and set the
desired time.
- Press the Start/Pause button.
• When washing full load or heavily soiled
laundry, you can increase effectiveness
by choosing intensive option.
• If Time Delay button is pressed, “3:00” is
displayed. The maximum delayed time is
19:00 hours and the minimum time is 3:00
hours.
• By selecting the Intensive option, the
wash time may be extended, depending
on the program selected.
• Each pressing of the button advances time
delay by one hour.
• To use this option press the Intensive
button once before the wash program is
started.
• To cancel the time delay, press the
Power button.
• Time Delay is ‘expected time’ from the
present to the completion of washing cycle
or selected process (Wash, Rinse, Spin).
• According to the condition of water supply and
temperature, the delayed time and the actual
washing time may vary.
21
H ow to use washer
Refresh
Turbo Steam
Turbo Steam
Time Left
___
Use on tough stained clothes.
___
Normal
1200rpm
___
• For tough stained clothes,
underwear, or baby clothes.
■ Refresh cycle
• For slightly wrinkled clothes which have
been stored for an extended time.
This cycle makes wrinkled clothes easy to iron
(Do not load wet clothes).
• Wrinkles will be reduced.
■ How to use Refresh cycle
1. Turn on the washer and select the Refresh program.
2. Load 5 items or less and close the door.
3. Press the Turbo Steam button repeatedly until
the desired and correct number of items is
displayed. Initial display is 3 items
• Steam Wash is available with
Refresh, Allergy Care, Baby
Care, Cotton, Cotton Quick,
Synthetic.
Turbo Steam
Time Left
0:20
Refresh
___
___
___
___
Press the Turbo Steam button
Turbo Steam
• This option features upgraded washing
performance with low energy and water
consumption.
• Do not load delicates such as wool, silk,
and easily discolored clothes.
NOTE:
- The concentrated steam wash function is
highly efficient. There should be no visible
water level during the Steam Wash
function.
- Steam spray may not be seen clearly
through the door; however, the washer is
spraying steam strongly inside.
- During the steam operation, a spraying
sound will be heard. This is not a
malfunction.
! CAUTION
Do not reach into the washer while operating.
Steam can cause severe burns.
Load
___
Time Left
0:20
___
___
4 items.
___
4. Press the Start/Pause button.
[Precautionary Notes]
- The Refresh cycle is not like other washing or
drying cycles.
- After the Refresh cycle is complete, the washer will
tumble the clothes for up to 30 minutes to prevent
rewrinkling.
- Due to the characteristic of cotton fibers, this cycle
is not recommended for 100% cotton clothing.
- Remove stains from clothing before using the
Refresh cycle to prevent permanently setting the
stains by high heat.
- Be sure that the tap is open. This cycle uses a little
water to produce steam.
- Be careful not to touch the door. It can be very hot.
- Do not open the door while operating.
Steam can cause severe burns.
- After removing clothes from the Refresh cycle they
may feel slightly damp wait at least 10 minutes
before putting the clothes on.
- Best result are achieved when articles are of similar
size and fabric type. Do not overload (avoid loading
more than 3 dress shirts if loading up to 5 Items.)
! CAUTION:
22
- Do not reach into the washer while operating.
Steam can cause severe burns.
- Keep pets away from the washer.
H ow to use washer
Tub Clean
Dry
Tub Clean course can be set by pressing
and holding Spin and Temp. button
simultaneously.
When Tub Clean course is set, display
“Tub Clean”, and all buttons are inoperable.
Time Left
___
• This washer-dryer’s automatic process
from washing to drying can be selected
easily.
___
• For most even drying , make sure all
articles in the clothes load are similar in
material and thickness.
Tub Clean
Pre
Wash
___
___
• Do not overload above the maximum
drying capacity indicator. Items must be
able to tumble freely.
TUB CLEAN is special cycle to clean the
inside of the washer. This cycle uses higher
water level with higher spin speed. Perform
this cycle regularly.
• By turning the dial, you can select.
Normal ➔ More ➔ 30 ➔ 60 ➔ 90 ➔ 120
➔ 150 ➔ Low Temp➔ Iron
How to use the Tub Clean cycle:
1. Remove any clothing or items from the
washer and close the door.
2. Open the dispenser drawer and add Anti
limescale (Calgon) to the Main wash
compartment.
NOTE: Do not add any detergent to the
detergent compartments. Excessive
suds may generate and leak from the
washer.
3. Close the dispenser drawer slowly.
4. Power On and then press and hold
Spin and Temp. button for 3 seconds. then
“Tub Clean” is displayed in LCD.
5. Press the Start/Pause button to start.
6. After the cycle is complete, leave the door
open to dry around the washer door
opening, flexible gasket and door glass.
1.Drying Automatic guide
! CAUTION: If there is a small child, be
careful not to leave the door
open for too long.
• Use your Automatic Cycles to dry most
loads.
Electronic sensors measures the
temperature of the exhaust to increase
or decrease drying temperatures for
faster reaction time and tighter
temperature control.
• Recommend Automatic drying course for
clothes type.
a) For Synthetics select - Low Temp.
b) If you want to iron clothes-Iron.
c) For Cottons select - Normal.
d) For washable nappies select - More
NOTE: The estimated drying time varies
from the actual drying time when
in the Automatic mode. The type
of fabric, size of the load, and the
dryness selected, do affect the
drying times.
23
H ow to use washer
2. Manual Drying time guide
• By turning the Dry button, the drying time
can be selected.
• Drying course can last up to 150min. When
selecting drying only, drying course will
start after spining, unless the spin omitted.
• These drying times are given as a guide to
help you set your dryer for manual drying.
Drying times can vary greatly depending on
dampness, room temperature and type of
fabric and your own experience will be your
best guide.
Woolen Articles
- Do not tumble dry woolen articles. Pull them
to their original shape and dry them flat.
- Some woven and loop knit materials may shrinks,
by varying amounts, depending on their quality.
- Always stretch ont these type of garments
immediately after drying.
Permanent Press and Synthetics
- Do not overload your dryer
- Take out permanent press articles as soon
as the dryer stops to reduce wrinkles.
Fiber or Leather Materials
- Always check the manufacture’s instructions.
Baby clothes and Night Gowns
- Always check the manufacture’s instructions.
Rubber and Plastics
- Do not dry any items made from or
containing rubber or plastics, such as:
a) aprons, bibs, chair covers
b) curtains and table cloths
c) bathmats
Fiber glass
- Do not dry fiberglass articles in your dryer.
Glass particles left in the dryer could be
picked up by your clothes the next time
you use the dryer and irri tate your skin.
24
H ow to use washer
Display
3. Completion of washing
20%
Time Left
1:12
Washing
___
Normal
1200rpm
60°C
1. Special function display
• When washing cycle is completed,
“End of cycle” is displayed on the
“Multi display”.
4. Time left
• When Child lock is selected, the
“
” lamp is on.
• During washing cycle, the remaining
washing time is displayed.
• When time delay is selected, it shows the
remaining time before the finish of the
selected program.
• Recommended program by
manufacturer.
2. Self diagnose display
- Baby Care :
around 2 hours and 27 minutes
• If the washer encounters a fault during
operation, the associated fault will be
displayed.
- Allergy Care :
around 2 hours and 12 minutes
- Refresh : around 20 minutes
- Cotton : around 2 hours and 14 minutes
“
” : Water pressure sensing error
“
” : Problem of overfilling water
“
” : Door is not closed
- Cotton Quick :
around 1 hour and 48 minutes
“
” : Over load in motor
- Delicate : around 1 hour and 25 minutes
“ CE ” : Over load in motor
“
” : Water inlet trouble
“
” : Drainage trouble
“
” : Unbalanced load
“
” : Water temperature trouble
“ PF ” : The washer experienced a
power failure.
“ AE ” : Water leake
“ dHE ” : The washer experienced a
power failure.
- Synthetic :
around 1 hour and 40 minutes
- Hand Wash/Wool :
around 1 hour and 13 minutes
- Quick30 : around 30 minutes
• The washing time may vary by the
amount of laundry, water pressure,
water temperature and other washing
conditions.
• If an unbalanced load is detected or if
the suds removing program operates,
the wash time may be extended.
(Max. increasing time is 45 minutes.)
If these error letters are displayed, please refer
to the troubleshooting page30 and follow the
guide.
25
M aintenance
❋ Before cleaning the washer interior, unplug the electrical power cord to avoid electrical
shock to avoid electrical shock hazards.
❋ When disposing of the appliance, cut off the mains cable, and destroy the plug Disable
the door lock to prevent young children being trapped inside.
The water inlet filter
-"
" error message will blink on the control panel when water does not enter the
detergent drawer.
- If water is very hard or contains traces of lime deposit, the water inlet filter may
become clogged.
It is therefore a good idea to clean it from time to time.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard bristle
brush.
4. Tighten up the inlet hose.
26
M aintenance
The drain pump filter
❋ The drain filter collects threads and small objects left in the laundry.
Check regularly that the filter is clean to ensure smooth running of your machine.
! CAUTION
First drain using the drain hose and then open the pump filter to
remove whatever any threads or objects.
Be careful when draining if the water is hot.
❋ Allow the water to cool down before cleaning the drain pump, carrying out
emergency emptying or opening the door in an emergency.
1.
Open the lower cover cap ( ) by
using a finger. Turn the drain plug ( )
to pull out the hose.
1
2. Unplug the drain plug (
), allowing the
water to flow out. At this time use a
vessel to prevent water flowing on to the
floor. When water does not flow any
more, turn the pump filter ( ) open to
the left.
3
2
3. Remove out any foreign material from
the pump filter (
).
4. After cleaning, turn the pump filter (
)
clockwise and insert the drain plug ( )to
the original place. close the lower cover
cap.
3
2
27
M aintenance
Dispenser drawer
❋ After a while detergents and fabric softeners leave a deposit in the drawer.
MAX
MAX
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the catch
downward and by pulling it out.
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.
The drawer recess
❋ Detergent can also accumulate inside the recess which should
be cleaned occasionally with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a
rinse cycle without laundry.
The washing drum
• If you live in a hard water area, lime scale may continuously build up in places where it cannot be
seen and thus not easily removed.
Over time the build up of scale clogs appliances, and if it is not kept in check, expensive
maintenance or repairs may result.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal
articles (paper clips, safety pins) which have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descalling agents, dyes or bleaches, make sure they are suitable for washing machine
use.
❋ Descaler may contain chemicals that may damage part of your washing machine.
❋ Remove any spots with a stainless steel cleaning agent.
❋ Never use steel wool.
28
M aintenance
The water circulation nozzle & steam nozzle
• Clean the water circulation nozzle, if clogged.
Cleaning your washer
1. Exterior
Proper care of your washer can extend its life.
The outside of the machine can be cleaned with warm water and a neutral non abrasive
household detergent.
Immediately wipe off any spills. Wipe with damp cloth.
Try not to hit surface with sharp objects.
❋ IMPORTANT: Do not use methylated spirits, diluents or similar products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass.
Run washer through a complete cycle using hot water.
Repeat process if necessary.
NOTE
Remove hard water deposits using only cleaners labeled as safe for washing machine.
Winterizing instructions
If the washer is stored in an area where freezing may occur or moved in freezing
temperatures, follow these instructions to prevent damage to the washer:
1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into an empty wash drum.
Close the door.
5. Set spin cycle and let washer spin for 1minute to drain out all water.
Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry the drum interior, and close the door.
7. Remove dispenser drawer, drain and dry excessive water from the compartments.
8. Store washer in an up right position.
9. To remove antifreeze from washer after storage, run empty washer
through a complete cycle using detergent. Do not add wash load.
29
roubleshooting guide
T
❋ This washing machine is equipped with automatic safety functions which detect and
diagnose faults at an early stage and react appropriately.
When the machine does not function properly or does not function at all, check the
following points before you contact your service provider.
Symptom
Possible Cause
Solution
Rattling and
clanking noise
• Foreign objects such as coins or
safety pins maybe in drum or
pump.
Stop washer and check drum
and drain filter.
If noise continues after washer
is restarted, call your authorised
service centre.
Thumping sound
• Heavy wash loads may produce
a thumping sound. This is usually
normal.
If sound continues, washer is
probably out of balance. Stop and
redistribute wash load.
Vibrating noise
• Have all the transit bolts and
packing been removed?
• Are all the feet resting firmly on
the ground?
If not removed during
installation. Refer to Installation guide
for removing transit bolts.
Wash load may be unevenly
distributed in drum. Stop washer and
rearrange wash load.
Water leaks.
• Fill hoses or drain hose are loose
at tap or washer.
Check and tighten hose connections.
• House drain pipes are clogged.
Unclog drain pipe. Contact plumber
if necessary.
• There is something between
the gasket and the glass.
Clean the gasket and
the glass with the towel.
Over sudsing
Water does not enter
washer or it enters
slowly
30
Too much detergent or unsuitable
detergent may cause excessive
foaming which may result in water
leaks, and vibration during spin.
• Water supply is not adequate in
area.
Check another tap in the house.
• Water supply tap is not
completely open.
Fully open tap.
• Water inlet hose(s) are kinked.
Straighten hose.
• The filter of the inlet hose(s)
clogged.
Check the filter of the inlet hose.
T
roubleshooting guide
Symptom
Possible Cause
Solution
Water in the washer
does not drain or
drains slowly.
• Drain hose is kinked or clogged.
Clean and straighten the drain hose.
• The drain filter is clogged.
Clean the drain filter.
Washer does not start
• Electrical power cord may not be
plugged in or connection may be
loose.
Make sure plug fits tightly in wall
outlet.
• House fuse blown, circuit breaker
tripped,or a power outage has
occurred.
Reset circuit breaker or replace fuse.
Do not increase fuse capacity.
If problem is a circuit overload, have
it corrected by a qualified electrician.
Turn on water supply tap.
• Water supply tap is not turned
on.
Washer will not spin
❋ Check that the door is firmly
shut.
Once started, the door can not be
opened for safety reasons.
Wait one or two minutes before
opening the door to give the electric
locking mechanism time to release.
Door does not open
Display stuck
on 6min left.
Close the door and press the
Start/Pause button. After pressing the
Start/Pause button, it may take
a few moments before the clothes
washer begins to spin. The door must
lock before spin can be achieved.
This washing machine checks
the condition of the clothes at
6min left to evaluate if they are
dried or not. If the clothes are not
dried, the washing machine will
further dry for 30min. The 6min
display will then continue to count
down after 30min.
Check the weight of clothes.
The weight of the clothes
should be less then 6kg.
31
roubleshooting guide
T
Symptom
Wash cycle time
delayed
Possible Cause
• It takes time to balance the
laundry before the spin cycle
Solution
The washing time may vary by the
amount of laundry, water
pressure, water temperature and
other usage conditions.
If the imbalance is detected or if the
suds removing program works, the
wash time shall be increased.
Stop the wash and pull out the
laundry then put it again to untwist
Dry problem
32
• Does not dry
Do not overload.
Check that the washer is draining
properly to extract adequate water
from the load.
Clothes load is too small to tumble
property. Add a few towels.
T
roubleshooting guide
Symptom
Possible Cause
Solution
• Water supply is not adequate in area
• Water supply taps are not completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are clogged.
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
• Load is too small.
Add 1 or 2 similar items to help
• Load is out of balance.
balance the load.
• The appliance has an unbalance detection and Rearrange load to allow proper
correction system. If individual heavy articles
spinning
are loaded (ex. bath mat, both robe, etc.), this
system may stop spinning or even interrupt the
spin cycle altogether.
• If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to balance
the load and repeat the spin cycle.
• Is the door opened or not
completely closed?
Close the door completely.
❋ If “
”is not released, call for service.
Unplug the power plug and call for service.
• Water overfills due to the faulty water valve.
• Water level sensor has malfunctioned.
Close the water tap.
Unplug the power plug.
Call for service.
• Over load in motor.
• Over load in motor.
• Water leake
Call for service
• The washer experienced a power failure.
Restart the cycle.
• Check water supply.
Turn the tap on
If
is not released, unplug power
plug and call service.
33
T
erms of Warranty
What Is Not Covered:
• Service trips to your home to teach you how to use the product.
• If the product is connected to any voltage other than that shown on the
rating plate.
• If the fault is caused by accident, neglect, misuse or Act of God.
• If the fault is caused by factors other than normal domestic use or use in
accordance with the owner's manual.
• Provide instruction on use of product or change the set-up of the product.
• If the fault is caused by pests for example, rats or cockroaches etc..
• Noise or vibration that is considered normal for example water drain
sound, spin sound, or warming beeps.
• Correcting the installation for example, leveling the product, adjustment of
drain.
• Normal maintenance which recommended by the owner's manual.
• Removal of foreign objects / substances from the machine, including the
pump and inlet hose filter for example, grit, nails, bra wires, buttons etc.
• Replace fuses in or correct house wiring or correct house plumbing.
• Correction of unauthorized repairs.
• Incidental or consequential damage to personal property caused by
possible defects with this appliance.
• If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training
center, dormitory)
If the product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement of a
defective part, shall be borne by the owner.
34
Download PDF