LG | WD-80180NU | LG WD-80180NU Owner’s Manual

Washing
Machine
OWNER'S MANUAL
WD(M)-1018(0~9)S
WD(M)-8018(0~9)S
WD(M)-1018(0~9)N
WD(M)-8018(0~9)N
WD(M)-1018(0~9)T
WD(M)-8018(0~9)T
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner's manual carefully, it provides
on safe installation, use and maintenance.
instructions
Retain it for future reference.
Record the model and serial numbers of your
washing
machine.
P
roduct Feature
More economical
Intelligent
Wash
by Intelligent Wash System
System
detects the amount of load and water
temperature, and then determines the optimum
time to minimize energy and water
washing
water level and
consumption.
Child-Lock
The Child-Lock
system has been used
any button to
pressing
Low noise
change
to
prevent children from
the program
during operation.
speed control system
By sensing the amount of load and balance, it
to minimize the spinning noise level.
evenly
distributes load
Auto Restart
If the washing machine is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
C
ontents
Warnings....................................................................................3
Specification
..............................................................................4
Installation..................................................................................5
Care before
washing................................................................11
Adding detergent
.....................................................................12
Function ...................................................................................13
How to
use
washer ..................................................................14
Maintenance ............................................................................21
Troubleshooting guide
Terms of
2
.............................................................24
Warranty ...................................................................27
W arnings
READ ALL INSTRUCTIONS BEFORE USE
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
WARNING!
!
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock,
the washer, follow basic
?
Do not install
be
?
?
or
precautions, including
?
repair or replace any part of the washer
or attempt any servicing unless specifically
published user-repair instructions
that you understand and have the skills to carry
?
out.
Keep the area underneath and around your
appliances free of combustible materials such
lint, paper, rags, chemicals,
?
Do not leave the washer door open.
An open door could entice children to
or
?
Do not
or
Do not slam the washer door closed
or
try to
possibility of electric shock,
appliance from the power supply or
To minimize the
this
disconnect the washer at the household
on
moving. Wait
completely stopped.
can
have been
or spotted with
explosive substances (such as
wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may
ignite or explode.
To avoid such a result, carefully follow the
garment manufacturer's wash and care
unplug
crawl inside the washer.
laundry process
retardant of fabrics.
dry articles that
panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
distribution
hang
Never reach into washer while it is
The
or
force the door open when locked. This could
result in damage to the washer.
etc.
supervision is necessary if this appliance
by or near children.
Do not allow children to play on, with, or inside
this or any other appliance.
until the drum has
?
?
Close
the door
?
using
instructions.
as
is used
?
Do not wash
combustible
recommended in the user-maintenance
?
persons when
cleaned in, washed in, soaked in,
Do not
or
injury to
following:
tamper with controls.
instructions
or
store the washer where it will
exposed to the weather.
Do not
the
reduce the flame
?
push down the door excessively,
topple over the washer.
when washer door open.
This could
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
grounded. In the event of malfunction or breakdown, grounding will reduce the risk
by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
Do not use an adapter or otherwise defeat the grounding plug.
This
appliance
must be
of electric shock
?
?
If you don't have the proper outlet, consult
WARNING :
an
electrician.
connection of the equipment-grounding conductor can result in risk of electric
qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
Improper
shock. Check with
a
-
3
S pecification
WD-1018(0~9)S
WD-8018(0~9)S
Front
Name
Power
Weight / Max.
loading washing
WD-1018(0~9)T
WD-8018(0~9)T
machine
220-240V~ 50Hz
supply
Size
Wash
WD-1018(0~9)N
WD-8018(0~9)N
,
600mm(W) 360mm(D) 850mm(H) 600mm(W) 440mm(D) 850mm(H) 600mm(W) 550mm(D) 850mm(H)
Watt
52kg/2100W
3.5
capacity
Water
kg
0.3
Pressure
No
Spin
Spin
6kg
60
Permissible water
No
64kg/2100W
5kg
42
consumption
Spin Speed
57kg/2100W
-
10
kgf /
/ 400 / 500 / 600 / 800
/ 400 / 600 / 800 / 1000
72
cm2 (30~1000kPa)
[WD-8018(0~9)N/8018(0~9)S/8018(0~9)T]
[WD-1018(0~9)N/1018(0~9)S/1018(0~9)T]
Accessories
Inlet hose
4
:
1EA
Spanner
nstallation
I
Install
or store where it will not be exposed to temperatures below freezing or exposed to the weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
In countries where there
particular attention
Any damage which may
pay
which may be
subject
to infestation
keeping the appliance
be cause by cockroaches
and its
surroundings
are areas
to
or
by cockroaches
or
other
vermin,
in clean condition at all times.
other vermin will not be covered by the appliance
guarantee.
Transit bolts
The
appliance
is fitted with transit bolts to
Removing
prevent internal damage during transport.
transit bolts
1. To
prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts
along
with the rubber
3. Take out the 4 bolts
along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future
?
?
If
they
are
not
removed, it may
use.
bungs.
cause
heavy
Whenever the
appliance
is
transported,
the
transit bolts must be refitted.
vibration, noise and malfunction.
2. Unscrew the 4 bolts with
the spanner
4. Close the holes with the caps
supplied.
supplied.
5
I
nstallation
Installation place requirement
Level floor
Drain Hose
Allowable
Washer
:
slope
Power outlet
under entire washer is 1˚
:
Must be within 1.5 meters of either side of location
of washer. Do not overload the outlet with more
than one appliance.
Additional Clearance :
For wall, door and floor modeling is
Laundry
Tub
approx.
2cm
(10cm
: rear
Do not
place
/2cm:right
or
store
& left
required.
side)
laundry products
washer at any times.
They can damage the finish
or
on
top of
controls.
650
850
600
BS
Plug Safety Details (For
U.K.
User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This
Green and
appliance
Yellow(Earth)
must be earthed
E
Brown(Live)
L
Blue(Neutral)
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the
or coloured Green or Green and Yellow.
letter E or by the earth symbol
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red.
If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
identifying
6
nstallation
I
Electrical connection
1. Do not
use an extension cord or double adapter.
supply cord is damaged, it must be replaced by the
or similarly qualified person in order to avoid a hazard.
Always unplug the machine and turn off the water supply
2. If the
3.
4. Connect the machine to
5. The
?
?
?
appliance
must be
an
manufacturer
after
so
that the
plug
is
easily
its service agents
use.
earthed socket in accordance with current
positioned
or
wiring regulations.
accessible.
Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen
hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below freezing point.
If the appliance is delivered in the winter months and temperatures are below freezing : Store the
washing machine at room temperature for a few hours before putting it into operation.
Washing Machine
is to be connected to the water mains
sets and that old hose-sets should not be used.
using
new
hose-
Connecting water supply hose
Water supply pressure must be between
30kPa and 1000kPa (0.3~10kgf/cm2)
Don't
strip or crossthread when connecting
Inlet hose to the valve.
If the water supply pressure is more than
1000kPa, a decompression device should be
installed.
?
?
Two rubber seals are supplied with the
water inlet hoses these are in order to
prevent water leaks.
Check water tightness of washing
machine connections by turning the tap
completely
?
on.
Periodically check the condition of the
replace the hose if necessary.
hose and
?
Hot water tap
Cold
Hot(option)
Cold
water
Make sure that there is no kink
hose and that it is not crushed.
When your washer has
tap
?
?
two
on
the
valves,
The Inlet hose which has red connector is
for the hot water tap.
If the washer has two valves, the energy
is saved by using hot valve.
7
nstallation
I
Normal Tap without thread &
1. Unscrew the fixing
attach the tap.
screw
to
2.
screw
type inlet hose
Push the connector up till the
rubber
packing
3.
is in
with the tap. Then
tight contact
tighten the 4
screws.
Normal Tap without thread &
1. Untighten the upper
connector
2.
touch type inlet hose
one
Push the upper connector up till
the rubber packing is in tight
screw.
contact with the
tighten
?
In
case
large
Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
the 4
(Single
3. Connect the
water
inlet
supply
models)
hose
to the middle connector,
tap. Then
pushing
the
plate
down.
screws.
the diameter of the tap is
the guide plate.
remove
?
Turn the middle connector not
to have water leaked.
?
Make
sure
that the rubber seal
is inside the hose connector.
?
To
separate the
water
supply
hose from the middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate
?
down.
Your machine
comes
with
only
cold water connection.
?
Make
sure
that there
are no
kinks in the hose and that it is
not crushed.
8
nstallation
I
This
equipment
is not
designed
for maritime
use or
for
use
mobile installations such
caravans, aircraft etc.
Turn off the stopcock if the machine is to be left for any length of time
especially if there is no floor drain(gully) in the immediate vicinity.
as
(e.g. holiday),
of the appliance, cut off the mains cable, and destroy the plug Disable the
prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
When
disposing
door lock to
of suffocation !
Keep
all
packaging
well away from children
Installation of drain hose
?
When
installing the drain hose sink,
it tightly with a string.
Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
secure
?
?
?
?
The drain hose should not be
placed
higher than 100 cm above the floor.
Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
When the drain hose is too long, do
not force back into the washer. This
will
cause
abnormal noise.
9
I
nstallation
Level
adjustment
1.
Adjusting the washing machine level
properly prevents excessive noise and
vibration.
Install the
floor
the
2.
appliance
on a
solid and level
surface, preferably in
a corner
of
room.
If the floor is uneven, adjust the
adjustable feet as required. (do not
insert
pieces
Make
sure
of wood etc. under the
that all four feet
are
feet)
stable
and
resting on the floor and then check
appliance is perfectly level. (use
a spirit level)
that the
After the washer is level, tighten the lock
nuts up towards of the base of the washer.
All lock nuts must be tightened.
Diagonal Check
When pushing down the edges of the
washing machine top plate diagonally, the
machine should not move up and down at
(Please, check both of two directions)
all.
If machine rocks when pushing the machine
top plate diagonally, adjust the feet again.
10
C
are
before
washing
Caring before washing
1. Care Labels
Look for
garment
2.
label on your clothes. This will tell you about the fabric content of your
and how it should be washed.
a care
Sorting
To
get the best results, Sort clothes into loads that
be washed with the
can
same
wash
cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint
transfer
Soil
causing discoloration
lightly soiled one.
can occur
soiled items with
(Heavy, Normal, Light)
(White, Lights, Darks)
(Lint producers, Collectors)
Color
Lint
3.
Caring
before
of white etc. If
do not wash
possible,
heavily
Separate clothes according to amount of soil.
Separate white fabrics from colored fabrics.
Wash lint producers and lint collectors
separately.
loading
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
?
Check all
that
pockets
to make sure
empty. Items such
nails, hair clip, matches, pens,
they
are
coins and
keys
can
damage
as
both
your washer and your clothes.
?
Close
zippers,
make
sure
snag
?
on
hooks and
other clothes.
Pre treat dirt and stains
a
little
strings to
that these items don't
detergent
by brushing
dissolved in water
onto stains like collars and cuffs to
help
shift dirt.
11
A dding detergent
Adding detergent and fabric softener
1. The Dispenser Drawer
3. Detergent
?
The
dosage
detergent should be used according to
of the detergent manufacture.
the
instruction
max
?
If too much detergent
is used
more
than the
recommended amount, too many suds can
occur and this will decrease the washing result
heavy
malfunction)
or cause
?
?
Main wash
?
only
2.
Detergent usage
)
temperature,
MAX
MAX
125 ml
125ml
Full load
can cause
early dispensing
Do not leave the fabric softener in the
detergent drawer for more than
(Fabric softener could harden)
Softener will
during
?
automatically
cycle.
2
days.
be added
the last rinse
Do not open the drawer when water is
supplied.
?
Solvents(benzene, etc)
are
not
allowable.
NOTE
Do not pour fabric softener
directly on
12
the clothes
:
to
3/4 of the normal amount.
Minimum load
?
:
1/2 of full load.
Detergent is flushed from the dispenser
beginning of the cycle.
the
clothes.
?
according
:
manufacturer's recommendation.
of the fabric softener which could stain
?
adjusted
hardness,
Tips
Do not exceed the maximum fill line.
Overfilling
water
results, avoid oversudsing.
Part load
?
may need to be
size and soil level of the load. For best
Adding Fabric Softener
(
(Causing a
Use powder detergent only for the front
loading washer.
for water
?PreWash+MainWash
load to the motor.
at
F
unction
Recommended
courses
according
Fabric
to the
Maximum
Proper
Program
Option
Type
First check if
95˚C
washable.
Pre Wash
WD-1018(0~9)S WD-1018(0~9)N WD-1018(0~9)T
WD-8018(0~9)S WD-8018(0~9)N WD-8018(0~9)T
Rinse+
Crease Care
(white cotton, linen
towel and sheets...)
Rating
Rating
Rating
Rating
Rating
Rating
Less than
Less than
Less than
Bio
Color fast gaments
(shirts, night dresses,
60˚C
pajamas...)and lightly (30˚C, 40˚C,
soiled white
60˚C-Eco)
cotton(underwear...)
Synthetic Polyamide, Acryic,
Polyester
Load
Temp.
laundry
is machine
Cotton
laundry type
40˚C
(60˚C, 30˚C)
Pre Wash
Rinse+
Crease Care
Bio
Pre Wash
Rinse+
Crease Care
1.5
kg
2.0
kg
3.0
kg
Bio
Delicate
Wool
Delicate
laundry
easily damaged
(silk, curtains...)
Machine washable
woolens with pure
new wool only
Hand
"Hand Wash" marked
Wash
delicate and wool
30˚C
Rinse+
(40˚C, Cold)
Crease Care
30˚C
Rinse+
(40˚C, Cold)
Crease Care
Cold(30˚C )
Rinse+
Crease Care
Less than
1.0
kg
Less than
1.0
kg
Less than
1.0
kg
Less than
1.5
kg
Less than
1.5
kg
Less than
1.5
kg
Less than
2.0
kg
Less than
2.0
kg
Less than
2.0
kg
laundry
Colored
Quick 30
which is
Laundry
lightly soiled
30˚C
Rinse+
Crease Care
Less than
1.0
kg
Less than
1.5
kg
Less than
2.0
kg
fast.
Pre Wash
laundry is heavily soiled, "Pre Wash" course is recommended. Pre Wash is available in
Synthetic Program.
Eco : By selecting Eco function, the water temperature is reduced and washing time is lengthened.
So you can economize in your consumption of heating energy.
Rinse+: Used to introduce an additional rinse, which may assist in removing traces of detergent residue.
Bio : If you want to eliminate protein stains (milk, blood, chocolate...), you may select Bio function by
pressing the option button.
NB. You can only select Bio function when temperature is higher than 60˚C in Cotton and Synthetic.
:
If the
Cotton and
13
ow
H
1. Cotton
to
use
washer
selected upon power
?
Press the
Power(
?
Press the
Start/Pause(
?
2. Manual
automatically
) button
to start.
) button.
?
?
Initial condition
-
-
-
Wash
:
main wash
Rinse
:
3 times
Spin
1000 rpm
:
Program
14
:
Cotton
) button
to start.
each button.
selecting the each conditions, please
refer to the page15~page20
?
[WD(M)-8018(0~9)N/
8018(0~9)S/ 8018(0~9)T]
Water temperature
Power(
Select the conditions which you want to
use, by turning the program dial and
pressing
800 rpm
-
Press the
For
[WD(M)-1018(0~9)N/
1018(0~9)S/ 1018(0~9)T]
-
Selecting
on.
:
60˚C
Press the
Start/Pause(
) button.
ow
H
to
use
washer
(1)
Dial
(2)
Button
:
Start / Pause
(Pre
(3)
Button
:
Option(Bio/Rinse+)
Button
:
(4) Button
Program
(5)
:
Option
Wash/ Crease
:
Care)
(6) Button
:
Time
Button
:
Power
(7)
Delay
Spin
Time
Delay
?
If Time
Delay button is pressed, "3:00" is
displayed. The maximum delayed time is
19:00 hours and the minimum time is 3:00
hours.
?
1. Time
Delay
?
Preparing washing before starting
"Time Delay"
Turn on the water tap.
-
Load
laundry and close the door.
detergent and fabric softener
Place the
the drawer.
?
How to set "Time
-
?
-
-
Delay"
Turn the
Program
Time
delay, press the
on
Power
'expected time' from the
completion of washing cycle
process (Wash, Rinse, Spin).
Delay
present
or
in
?
Press Power button.
To cancel the time
advances
button.
-
-
pressing of the button
delay by one hour.
Each
time
is
to the
selected
According to the condition of water supply and
temperature, the delayed time and the actual
washing time may vary.
dial to select
the program you require.
Press Time Delay button and set the
desired time.
-
Press the Start/Pause button.
(":" blinks.)
15
to
ow
H
use
washer
Child Lock
Water Temp.
If you choose to lock the buttons on the
control assembly to prevent tampering this
function may be selected.
1. Child Lock
?
Child Lock
Option
can
button
be set by pressing
simultaneously.
the two
?
the
By turning
temperature
-
-
?
?
When child lock is set, all buttons
except power button.
To deactivate Child Lock
two
Option
button
are
inoperable
system, press the
simultaneously again.
be selected.
Cold
30°C, 40°C, 60°C, 95°C
1. Water Temperature
?
Water temperature can be selected
according to the program.
The required temperature lamp
for identification.
?
To
change
to the desired program,
whilst in child lock mode.
1. Press both the two
once
Option together
again.
2. Press the Start/Pause button.
3. Select the desired program and press
the Start/Pause button
again.
Change
the desired
program
?
The child lock
can
be set at any time and
it is
automatically canceled when
operational errors occur. Also Child Lock
works when power is off.
16
the water
Program Dial,
can
For the
more
refer to
the page13.
detailed
will
light up
information, please
H
ow
to
use
washer
Spin
2. No spin
If
?
no
after
spin is selected,
draining water.
The
required lamp
identification.
[WD(M)-8018(0~9)N/ 8018(0~9)S [WD(M)-1018(0~9)N/ 1018(0~9)S
/ 8018(0~9)T]
/ 1018(0~9)T]
By pressing the Spin button,
spin speed can be chosen.
the
Spin Speed
program
?
as
is available
?
according
Is selected
by pressing
repeatedly
this function leaves clothes in
the
spin
button
the machine; suspended in the water
after a rinse without entering into spin.
1. Spin selection
?
will light up for
3. Rinse Hold
?
?
the washer stops
to the
follows.
WD(M)-8018(0~9)N/ 8018(0~9)S/ 8018(0~9)T
Cotton/Rinse+Spin/Synthetic/Wool/
To
proceed through
once
to
a
drain
spin,
completed
required
or
the rinse hold function is
using
to
Spin
button to the
program.
(Spin)
-
Hand Wash/Delicate/Quick 30
RinseHold-NoSpin-400-500-600-800
?
The
required lamp
identification.
will
light up for
WD(M)-1018(0~9)N/ 1018(0~9)S/ 1018(0~9)T
Cotton/Rinse+Spin/Synthetic/Wool/
-
Hand Wash/Quick 30
RinseHold-NoSpin-400-600-800-1000
-
Delicate
RinseHold-NoSpin-400-600-800
17
ow
H
to
washer
use
Program
Option
By pressing the Option button, all
Option functions may be selected.
?
Bio
-
-
Rinse
+
8 programs
?
Pre Wash
-
-
Crease Care
are
available
according
to the
laundry type.
1. Bio
Lamp
?
will
up to indicate selected
light
program.
If you want to eliminate
protein
stains(milk, blood, chocolate...), you may
select Bio function by pressing the option
button. [You can select Bio function when
temperature is higher than 60˚C in cotton
and Synthetic.]
?
1. Program
?
When Start/Pause button is
Cotton program is
-
By turning
the
pressed, the
automatically selected.
Program dial,
selected in order of
Quick 30
2. Rinse+
Wash
Used to additional
?
in
removing
rinse, which may assist
traces of
By selecting Rinse+ function,
?
residue.
detergent
time and the rinse water
are
laundry
course
?
is
heavily soiled,
"Pre Wash"
is effective.
Pre Wash is available in Cotton and
required lamp
will light up for
identification.
4. Crease Care
?
If you want to prevent crease, select this
button with spin speed.
18
-
-
Rinse+Spin Drain
Synthetic".
Wool
-
-
Hand
-
2. Course
-
Synthetic.
The
the program is
Delicate
Regarding to the laundry type for each program
Please refer to the page13.
-
If the
Cotton
the rinse
increased.
3. Pre Wash
?
-
-
"
-
Cotton
Quick 30
Synthetic
-
-
-
Delicate
Wool
Hand Wash
-
-
Rinse+Spin
Drain
ow
H
to
use
washer
Start/Pause
Power
1. Power
1. Start
?
?
This Start/Pause button is used to start
wash
cycle
or
pause the wash
Press the Power button to turn power
on
and off
cycle.
?
To cancel the Time
Delay function,
pressed.
if the
power button should be
2. Initial Program
2. Pause
?
?
If temporary stop of wash cycle is
needed, press the Start/Pause button.
When in
4 minutes.
?
NB. The door will not open before 1 to 2
minutes when Pause is selected,
or
at the end of the wash
When the Power button is
pressed,
the
for Cotton program. And
the other initial conditions as follows.
Pause, the power is turned off
automatically after
?
?
washer is
ready
So, if you
want to advance into the
washing cycle without changing the
program, just press the Start/Pause
button and then the washer will proceed.
cycle.
Initial program
[WD(M)-8018(0~9)N/
8018(0~9)S/ 8018(0~9)T]
-
Cotton 60˚C / 800 rpm
[WD(M)-1018(0~9)N/
1018(0~9)S/ 1018(0~9)T]
-
Cotton 60˚C / 1000 rpm
19
H
ow
to
washer
use
Display
3. Completion of
?
When
washing cycle is completed,
is displayed on the "Multi
display".
"
"
1. Special function
display
When child lock is selected, the
is displayed.
?
"
"
4. Time left
When time
?
the
delay is selected, it shows
remaining times to finish the
?
selected program.
During washing cycle, the remaining
washing time is displayed.
Recommended program
?
2. Self
?
operation,
displayed.
a
fault
during
the associated fault will be
-
-
-
"
"
:
Water pressure
sensing
error
-
"
"
"
"
:
Problem of
overfilling
water
-
:
Door is not closed
-
"
"
:
Water inlet trouble
-
"
"
"
"
"
"
:
Drainage
trouble
-
:
Unbalanced load
-
:
by
manufacturer.
diagnosis display
If the machine encounters
washing
Water temperature trouble
If these error letters are displayed, please
refer to the troubleshooting page24 and
follow the guide.
?
(
)
:
WD-1018(0~9)S/8018(0~9)S
<
> :
WD-1018(0~9)T/8018(0~9)T
Cotton 95˚C : around 2 hours and
Cotton 60˚C
:
27(17)<37> minutes
around 2 hours and 35 minutes
around 1 hour and 22 minutes
Synthetic
:
Delicate
:
around 56 minutes
Wool
:
around 58 minutes
Hand Wash : around 57 minutes
Quick 30 : around 30 minutes
Rinse+
Spin
:
around 20 minutes
Drain : around 1 minutes
The
washing time may vary by the
laundry, water pressure,
water temperature and other washing
amount of
conditions.
?
If
an
unbalanced load is detected
the suds
or
if
removing program operates,
the wash time may be extended.
(Max. increasing time is 45minutes.)
20
M
aintenance
Before
cleaning the washer interior, unplug the
electrical power cord to avoid electrical
shock to avoid electrical shock hazards.
When
disposing
of the
cut off the mains
appliance,
door lock to prevent young children
being trapped
cable, and destroy the plug Disable the
inside.
The water inlet filter
-"
"
error
detergent
-
message will blink
If your water is very hard
become
on
the control
panel
when water does not enter the
drawer.
clogged.
a good
It is therefore
or
contains traces of lime
deposit,
the water inlet filter may
idea to clean it from time to time.
2. Unscrew the
1. Turn off the
water
water inlet
tap.
hose.
3. Clean the
filter
4.
using
Tighten
up
the inlet
a
hard bristle
hose.
brush.
The drain pump filter
The drain filter collects threads and small
Check
!
regularly that the filter
CAUTION
First drain
is clean to
using
any threads
or
Open the lower cover
cap( )byusinga
2.
in the
smooth
laundry.
running of your
machine.
the drain and then open the pump filter to
remove
whatever
objects.
Be careful when
1.
objects left
ensure
draining
if the water is hot.
Unplug the drain plug ( ),
allowing the water to flow out.
3. Remove any
At
this time
plug( )topullout
water
the hose.
water does not flow any more, turn
plug (
the pump filter
close the lower
flowing
vessel to
on
prevent
to the floor. When
(
)
open to the left.
cleaning,
(
). After
( )
turn the pump filter
coin. Turn the drain
use a
material
foreign
from the pump filter
clockwise and insert the drain
)to the original place.
cover
cap.
100
3
1
2
3
2
21
aintenance
M
Dispenser drawer
After
?
?
?
a
while
and fabric softeners leave
detergents
It should be cleaned from time to time with
a
jet
of
a
deposit
water.
running
If necessary it can be removed completely from the machine
downwards and by pulling it out.
To facilitate
cleaning,
in the drawer.
by pressing
the upper part of the fabric softener compartment
the catch
can
be removed.
max
The drawer
Detergent
can
be cleaned
?
recess
also accumulate inside the
with
occasionally
washing
?
?
recess
which should
old toothbrush.
replace
the drawer and
run a
drum
If you live in a hard water area, limescale may
seen and thus not easily removed.
Over time the build up of scale
be replaced.
?
an
Once you have finished cleaning,
rinse cycle without laundry.
The
?
max
continuously
clogs appliances,
build up in
and if it is not
kept
places where
in check these may have to
metal articles
washing drum is made of Stainless steel, specks of rust can
(paper clips, safety pins) which have been left in the drum.
The
drum should be cleaned from time to time.
Although
the
washing
If you
use
descaling agents, dyes
or
bleaches, make
sure
they
are
be caused
suitable for
Remove any
Never
22
use
spots with
steel wool.
a
stainless steel
damage part of
cleaning agent.
your
washing
by
washing
use.
Descaler may contain chemicals that may
it cannot be
machine.
small
machine
aintenance
M
Cleaning
your washer
1. Exterior
of your washer
can
extend its life.
The outside of the machine
can
be cleaned with
Proper
care
household
water and
a
neutral
non
abrasive
detergent.
off any
Immediately wipe
Try
warm
not to hit surface with
IMPORTANT: Do not
spills. Wipe
with
damp cloth.
sharp objects.
methylated spirits,
use
diluents
or
similar
products.
2. Interior
Dry
around the washer door
Run washer
flexible
opening,
a
Remove hard water
and door
glass.
hot water.
through complete cycle using
Repeat process if necessary.
NOTE
gasket
deposits using only cleaners
labeled
as
washer safe.
Cold condition
If the washer is stored in
an area
where
temperatures, follow these instructions
1. Turn off water
Plug
4. Add
to
may
occur or
prevent damage
moved in
freezing
to the washer:
supply tap.
2. Disconnect hoses from water
3.
freezing
electrical cord into
1gallon(3.8L)
a
supply
and drain water from hoses.
properly grounded
of nontoxic recreational
electrical outlet.
vehicle(RV) antifreeze into
an
empty wash drum.
Close the door.
5. Set
spin cycle
and let washer
spin
Not all of the RV antifreeze will be
6.
Unplug
electrical power cord,
7. Remove
dispenser
8. Store washer in
9. To
remove
through
a
an
for 1minute to drain out all water.
expelled.
dry the
drawer drain and
drum
dry
interior, and close the door.
excessive water from the compartments.
uprignt position.
antifreeze from washer after storage,
complete cycle using detergent.
run
empty washer
Do not add wash load.
23
T roubleshooting guide
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an
early stage and react appropriately
When the machine does not function properly or does not function at all, check the following points before
you contact your service provider.
Possible Cause
Symptom
Rattling and
clanking noise
?
Solution
Foreign objects such as coins
safety pins maybe in drum or
or
Stop washer
and check drum
and drain filter.
If noise continues after washer
pump.
is
restarted, call your authorised
service centre.
Thumping
sound
?
Heavy wash loads
thumping sound.
a
may produce
This is usually
normal.
Vibrating
noise
?
?
redistribute wash load.
If not removed
Have all the transit bolts and
packing
been removed?
Are all the feet
the
If sound continues, washer is
out of balance. Stop and
probably
during
installation. Refer to Installation
resting firmly
on
for
removing
guide
transit bolts.
Wash load may be unevenly
distributed in drum. Stop washer and
ground?
rearrange wash load.
Water leaks.
?
Fill hoses
at
?
tap
or
or
drain hose
are
loose
Check and
tighten
hose connections.
washer.
House drain
pipes
are
clogged.
Unclog
drain
pipe.
Contact
plumber
if necessary.
Too much
detergent or unsuitable
detergent may cause excessive
foaming which may result in water
Oversudsing
leaks.
Water does not enter
washer
or
?
supply
adequate
in
Check another tap in the house.
area.
it enters
slowly
Water
is not
is not
?
Water
?
Water inlet
?
The filter of the inlet
supply tap
completely open.
hose(s)
are
Fully
kinked.
hose(s)
open tap.
Straighten
hose.
Check the filter of the inlet hose.
clogged.
Water in the washer
does not drain
drains
24
slowly.
?
Drain hose is kinked
?
The drain filter is
or
clogged.
or
clogged.
Clean and
straighten
Clean the drain filter
the drain hose.
T roubleshooting guide
Possible Cause
Symptom
Washer does not start
?
Electrical power cord may not
plugged in or connection
be
Solution
Make
plug fits tightly
sure
in wall
outlet.
may be loose.
?
House fuse
breaker
blown, circuit
tripped,or
a
power
outage has occurred.
Reset circuit breaker
Do not increase fuse
If
problem
is
it corrected
?
Water
supply tap
is not turned
Turn
on
a
by
water
replace
capacity.
or
fuse.
circuit overload, have
a qualified electrician.
supply tap.
on.
Washer will not
spin
Check that the door is
shut.
firmly
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the clothes
washer
begins to spin. The door
spin can be
must lock before
achieved.
Door does not open
Once started, the door can not be
for safety reasons.
opened
Wait
one or
two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash
cycle
delayed
time
The
washing time may vary by the
laundry, water
amount of
pressure, water temperature and
other usage conditions.
If the imbalance is detected or if the
suds removing program works, the
wash time shall be increased.
25
T roubleshooting guide
Possible Cause
Symptom
?
Water
?
Water
?
?
supply is not adequate in area
supply taps are not completely
open.
Water inlet
hose(s)
are
The filter of the inlet
are
Check another tap in the house.
Fully
open tap.
Straighten hose(s).
kinked.
hose(s)
Solution
clogged.
Check the filter of the inlet hose.
?
Drain hose is kinked
Clean and
?
The drain filter is
Clean the drain filter.
?
Load is too small.
Add 1
?
Load is out of balance.
balance the load.
?
The
Rearrange
spinning
appliance
or clogged.
clogged.
has
imbalance
an
detection and correction system. If
individual heavy articles are loaded
or
straighten the
drain hose.
2 similar items to
help
load to allow proper
etc.) this system
spinning or even interrupt the
spin cycle altogether.
If the laundry is still too wet at the end of
the cycle, add smaller articles of laundry
to balance the load and repeat the spin
cycle.
(ex.
bath mat, both robe,
may stop
?
?
Is the door
Close the door.
opened?
If"
"is not released, call for service.
Unplug the
power
plug
service.
?
Water overfills due to the
faulty water
valve.
?
26
Water level
Close the water tap.
Unplug the power
Call for service.
sensor
has malfunctioned.
plug.
and call for
T
of Warranty
erms
What Is Not Covered:
?
?
?
?
Service
trips
to your home to teach you how to use the
If the
product
rating plate.
is connected to any
If the fault is caused
If the fault is caused
voltage
by accident, neglect, misuse
by
product.
other than that shown
or
on
the
Act of God.
factors other than normal domestic
use or use
in
accordance with the owner's manual.
?
?
?
Provide instruction
on use
If the fault is caused
Noise
or
product
or
change the set-up of the product.
by pests for example,
rats or cockroaches etc..
vibration that is considered normal for
sound, spin sound,
?
of
Correcting
or
example
water drain
warming beeps.
the installation for
example, levelling
the
of
product, adjustment
drain.
?
?
Normal maintenance which recommended
Removal of
by the
owner's manual.
foreign objects / substances from the machine, including the
example, grit, nails, bra wires, buttons etc.
pump and inlet hose filter for
?
?
?
?
Replace
fuses in
or
correct house
wiring
or
correct house
plumbing.
Correction of unauthorized
repairs.
Incidental or consequential damage to personal property
possible defects with this appliance.
If this
product
(Example
:
caused
by
is used for commercial purpose, it is not warranted.
Public
places
such
as
public bathroom, lodging house, training
center, dormitory)
If the
product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement
defective part, shall be borne by the owner.
of
a
27
For U.K. Customer
CUSTOMER SERVICES
:
0870-592-9929(Service Force)
Mon.-Fri. 8:30AM
LGEUK SERVICE WEB-SITE
P/No.: 3828ER3014G
:
-
5:30PM
www.lgelectronics.co.uk
Download PDF