LG | WF-F5700PCX | LG WF-F5700PCX Owner’s Manual

Washing
Machine
OWNER'S MANUAL
MODELS
:
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
5101(~5),5111(~5),5121(~5) PC(D/M)(X/K)
5201(~7),5211(~7),5221(~7) PC(D/M)(X/K)
5401(~5),5411(~5),5421(~5) TC(D/M)(X/K)
5700, 5710, 5720 PC(D/M)(X/K)
6101(~5),6111(~5),6121(~5) TC(D/M)(X/K)
6201(~7),6211(~7),6221(~7) TC(D/M)(X/K)
6700, 6710, 6720 TC(D/M)(X/K)
WF-F60PC
WF-F63PC
Please read this manual
carefully before operating
your set.
Retain it for future reference.
Record model name and serial number of the set.
Quote this information to your dealer when you require service.
P
roduct Features
Fuzzy Logic Control
A built-in load
automatically detects and measures the laundry load and
microprocessor optimizes washing conditions such as ideal water level and
washing time.
sensor
a
Advanced
the best
technology is built
washing result.
into the Electronic Control
SENSING
START
Laundry
System
SETTING
Sensor
Optimum
Washing
Water Level Sensor
WASHING
Condition
3
which
ensures
AUTO
POWER
OFF
Step washing
3 step
washing
makes best
washing performance with
Rubbing and Shaking
Rubbing
low
tangling.
Shaking and Disentangling
Lint Filter
Lint and loose threads from
washing cycle
are
caught by
laundry generated during
the lint filter for
a
the
cleaner wash.
Auto Restart
In the event of
start its
a power failure, the washing machine will automatically
interrupted cycle when power is resumed.
¡ APPLIED MODELS
:WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
WF-F(C/S)
ATTENTION :Be
sure
5101(~5),5111(~5),5121(~5) PD(X/K)
5201(~7),5211(~7),5221(~7) PD(X/K)
5401(~5),5411(~5),5421(~5)TD(X/K)
5700, 5710, 5720 PD(X/K)
6101(~5),6111(~5),6121(~5)TD(X/K)
6201(~7),6211(~7),6221(~7)TD(X/K)
6700, 6710, 6720 TD(X/K)
to remove the unit from the carton
machine will not be able to operate
properly.
base, otherwise the
C
ontents
Read this manual
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
in the
Troubleshooting
section. If you review
our
chart of
Troubleshooting Tips first,
you
may not need to call for service at all.
Introduction
Before
Starting
Safety
to Wash
Information
Identification of Parts
5
Function Information
6
Preparation Before Washing
7
Use of Water,
Washing Programs
Detergent,
Bleach and Softener 8
How to Remove Stains
11
Function of each Button
12
Fuzzy
Wash
Economy
Additional Function
Options
Installation
Care and Maintenance
4
(Normal Wash)
Wash
14
14
Jean Wash
14
Wool Wash
14
Turbo Wash
14
Delay Start (Reservation)
Wash
16
Option Washing
17
Other useful Functions
18
Placing
and
Connecting
Water
Connecting
Drain Hose
Grounding
19
Leveling
Supply
Hose
Method
23
24
25
Cleaning
Cleaning
20
and Maintenance
26
Troubleshooting
Troubleshooting
27
Terms of
Terms of
30
Warranty
Specification
Warranty
Specification
31
4
S
afety
information
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Introducin
For your better understanding, these precautions are separated into two categories.
We urge you to pay special attention to them in the interests of your own safety, and
machine against damage:
Caution
Violation of these
Attention
Following
these
guidelines could result in
guidelines
serious
will protect your machine
Installation
appliance
is not intended for use
or
infirm persons without
Do not place any rugs
over the power cord.
Since the machine is
source.
children should be
Make
Supply
to
cord
sure
to
to
ensure
ground the earth wire or connect it
Make
sure
ground detector after you put the power cord
into an outlet.
not move.
When the power cord is loose, do not
Do not damage the power cords.
hands.
Do not
plug many cords into
one
or
feet under this
heavy material
heavy,
a
minimum of
exposed to sunlight, wind, rain, etc.
The appliance must be positioned so
the plug is accessible
and
a
use
or
two persons should move it.
Do not install the washer where it is
that
Young
supervised
they do not play with the appliance.
The base opening must not be obstructed by
carpeting when the washing machine is installed on
a carpeted floor.
Power
against damage.
Do not put your hands
machine.
by young
supervision.
Do not install the washing machine in a damp place.
Keep the washing machine away from fire or heat
children
injury.
Attention
Caution
The
fatal
or
protection of your
it.
plug
that
the power cord is free of dust
properly so that the cord will
it in
Do not touch the power cord with wet
outlet at the
same
time.
If the power cord or fuse is damaged, it must be
replaced by the manufacturer or its service agents or
similarly qualified people in order to avoid a hazard.
If the appliance is supplied from a cord extension
set or electrical portable outlet device the cord
extension set or electrical portable outlet device
should be positioned so it is not subject to splashing
or ingress of moisture.
Do not place any electric appliance with a charging
battery, magnetically-driven appliance and magnetic
body on the washer.
Operation
When you take out the
fall into the washer.
laundry, be careful not to
?
Do not put hands into the rotating tub.
Do not sprinkle water over the buttons.
Make
sure
the lid is closed
activating the machine.
more than 50˚C(122˚F)
?
Do not pour
into the tub.
?
Do not wash any
during operation of the
Do not put heavy objects on the machine.
Unplug the cord when the machine is not in
Do not press the buttons with sharp objects.
Check the hose connection and open the tap
before
spin cycle.
Maintenance
?
?
use.
?
water
waterproof materials.
Do not pour corrosive materials or bleach
over the washing machine. It will cause
damage to the power cord or the machine.
Never disassemble or remodel the washer
and power cord by yourself. Only a
qualified technician should work on the
machine.
5
I
dentification of Parts
Body
Power cord
Water
supply hose(1
EA
or
2EA)
Powder
detergent box
()
Softener dispenser
()
Bleach
dispenser
()
Inner tub
Control
panel
Lint filter
AUTOOFF
Drain hose
for pump model
Pulsator
Adjustable leg
Drain hose for
non
pump model
Accessories
Water
supply
hoses
Drain hose
or
or
1 Each for cold and
hot water
Note
Part
can
be different
according to the model.
Anti-rat
cover
(option)
Introducin
6
Function
Information
Our machine provides various washing methods which suit various conditions and
types of laundry.
Different types of
laundry washing
Fuzzy(Normal)
Use this
Wash
Program for everyday washing e.g. sheets, towels, T-shirts. (refer
to
p14)
Jean Wash
Use this
Program for heavily soiled durable garments e.g. overalls, jeans.
heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed.
Thick and
to
(refer
p14)
Wool Wash
Delicate clothes
(lingerie, wool, etc.)
which may be
The fibers of machine washable woolens have been
easily damaged can be washed.
(refer to p14)
specifically modified to prevent felting when they are machine washed.
Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them
Before washing your woolens check the care label for the washing instructions.
?
?
?
?
When
washing woolens use a mild detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and
tumble action of a
dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.
(Ensure that the whole article is suitable for machine washing and not just the backing material.) You may wish to
handwash these articles and place them in the machine to spin dry.
Washing according to the condition of laundry
Economy
Wash
Economy wash can be
(refer
to
selected to wash
lightly
soiled clothes of less than 2.0
kg in
a
short time.
p14)
Turbo Wash
Turbo Wash is
laundry
with
designed to maximize washing performance and can be selected to
Fuzzy or Jean program. (refer to p14)
wash
heavily soiled
Other washing method
Delay
Delay
start Wash
start Wash
is used to
The number of hours to be
Option
delay the finishing time of the operation.
delayed can be set by the user accordingly.
(refer
to
p16)
Wash
Spin, Rinse/Spin, Rinse, Wash/Rinse,
and Wash
only options can selected. (refer to p17)
7
Before
Preparation
Washing
BeforStaingWsh
Sorting
results, different fabrics need to be washed in different ways.
Normal,
(Heavy,
Light)
Separate clothes according to amount of soil
COLOR (Whites, Lights, Darks)
Separate white fabrics from colored fabrics.
To get the best
SOIL
LINT
(Lint producers, Collectors)
Caring
?
before
Check all
such
as
Separate lint producers
and lint collectors.
loading
pockets to make sure that they are empty. Things
and keys can damage
nails, hairclips, matches, pens, coins
both your washer and your clothes.
?
Close
zippers, hook and strings to make sure that these items
don't snag
?
?
on
other clothes.
Mend any torn garments or loose buttons. Tears
become larger during washing.
Remove any loose brassiere wires
as
or
holes may
they can damage your
washing machine and clothes.
?
Pre-treat dirt and stains.
?
Make
?
Check the
sure
the clothes
are
WIRE
washable in water.
washing instructions.
Pretreatment
detergent dissolved in water onto stains like collars
help shift dirt.
Treat stains AS SOON AS POSSIBLE. The longer they are left the
harder they are to remove.
Brush
a
little
and cuffs to
Light
and
Large-size clothing
Clothes like downs and woollens
Long laundry
net and
are
light weight, large and float
wash them in
a small amount of water.
easily.So
nylon
If the laundry floats during the wash cycle, it may become damaged.
Use dissolved detergent to prevent the detergent from clumping.
use a
items
nylon nets for long, delicate items.
laundry with long strings or long length, a net will prevent
tangling during washing.
Fasten zippers or hooks on items before washing.
Nylon net is not supplied by LG.
Use
For
8
Use
BeforStaingWsh
of Water,
Detergent,
Bleach and Softener
Using water
Amount of water
?
This machine detects the
quantity of laundry automatically,
then sets the water level and proper amount of detergent.
?
When you select a wash program, the water level and
amount of detergent (to be used) will be shown on the
control
?
panel.
When the water level is
automatically detected, it may differ depending on the quantity of laundry even
though the same water level is indicated on the control panel.
Using Detergent and
Amount of
?
?
detergent.
For the correct amount of detergent, refer to
Available
?
detergent
When you select a wash program, the water level and the amount of detergent will be
shown on the control panel. The amount of a cup in the diagram is about 40g for
concentrated
?
Fabric Softener
detergent manufacturer's instruction
.
Detergent Type
Synthetic detergents that yield a low level of foam are recommended.
liquid detergent is used, mix it with water (1:1) and pour it into the bleach dispenser.
When
Attention
If excessive
pollution,
detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental
it accordingly.
so use
Available Fabric Softener
?
?
Type
Do not use concentrated fabric softener. This may cause some problems in automatic
more details refer to the softener products instructions for use.
For
dispensing.
9
Using Detergent and
How much
Fabric Softener
detergent
When you select a wash program the water level and the amount of detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated
detergent.
The correct amount of detergent will vary depending on the amount of soil in your clothes
and work cloches may need more detergent, while bath towels usually need less.).
(Jeans
liquid and concentrated detergents, follow the recommendations of the detergent manufacturer.
Note: To check you are using the correct amount of detergent, lift the lid of your machine
about half-way through the wash. There should be a thin layer of foam over the surface of the
water. Lots of foam may look good, but it does not contribute to cleaning your clothes. No
For
foam
means
not
enough detergent has been used; soil and lint can settle back
on
the clothes
or
washing machine.
If excess detergent is used, the rinse will not be as clean and efficient. Also, it could cause
environmental pollution, so use it accordingly.
the
Adding
the
detergent
Powder
Detergent dispenser.
()
Open the detergent dispenser and deposit the appropriate
amount of detergent
Where you
Where you deposit the detergent
deposit the
Powder Detergent dispenser.
detergent
Some detergents MUST be fully dissolved before
adding to your machine to get the best wash results.
Check the instructions on the detergent packet.
If you use powdered detergent it is essential that the required amount be fully dissolved in very hot water
before being added to warm or hot water for the actual wash.
Pre-dissolving detergent in warm water when washing in cold water can improve its performance.
10
U
BeforStaingWsh
of Water,
se
Detergent,
Available Fabric Softener
Do not
For
Type
concentrated fabric softener. This may cause some problems in automatic
details refer to the softener products instructions for use.
use
more
Depositing
?
Bleach and Softener
Don't
Fabric softener
softener with
use
detergent.
Softener
Use softener in
?
?
?
dispenser
()
last rinse water
?
dispensing.
When using dispenser, dilute
fresh water(25ml)
softener(25ml) with
When filling dispenser, do not
It may stain clothes.
Never pour fabric softener
It may stain them
splash or overfill.
or
directly on clothes.
If
spotting occurs, wet and rub hand
dishwashing liquid (or mild bar soap)
and rewash.
Note
Fabric Softener will be
Using
dispensed automatically during the final rinse.
Bleach
Check fabric
care
labels for
Available Bleach
Use
special instructions.
Type
oxygenated bleach.
Powdered bleach should mixed with water and then be
For
more
details refer to the
Depositing
?
?
products
instruction for
deposited into the tub.
use.
Bleach
Separate the laundry to be bleached
liquid bleach carefully, following instructions on
Bleach
Measure
?
?
?
dispenser
()
the bottle.
Before
starting the washer, pour measured amount of bleach
directly into bleach dispenser.
Avoid splashing or over-filling dispenser. If you prefer to
use powdered bleach, add it into the wash basket with your
detergent.
The dispenser dilutes liquid bleach before it reaches into
your wash load.
Attention
Never pour undiluted liquid bleach directly onto clothes
This may cause change of color or damage the laundry.
or
into the wash basket.
Do not mix chlorine bleach with ammonia
as
vinegar and/or rust remover. Mixing can reduce
toxic gas which may cause death.
Do not pour powered bleach into bleach
or
acids such
a
dispenser.
11
How
To Remove Stains
How To Remove Stains
Pretreating dirt and stains
Brush a little washing detergent dissolved in water onto stains, collars, and cuffs to help shift dirt.
The secret of stain treatment is immediate action. When an accident happens, plunge the stained area
into cold water, or sponge it down. This prevents the stain from setting. Wash as soon as possible
afterwards.
?
?
Treat stains AS SOON AS POSSIBLE. The
longer they
are
left, the harder they
Always consider the type of fabric you are treating to make sure you do not use
temperature that is too hot or a treatment that will alter the color of the fabric.
It pays to
pre-wash products
and solvents
on an
are
a
to remove.
water
inconspicuous part of the garment first.
?
Place the garment being treated on an absorbent cloth (e.g. on an old towel). Work from the
side of the stain, as this can force the stain off the fabric instead of through it.
?
Use cold
?
Some stains
or warm
are
water
not
easily
stain has been removed,
?
?
on
unknown stains
seen
as
hot water
can
set
when the fabric is wet. Do air
heat from
may set the
some
dry
stains.
the stained garment to be
care
with stain removal
a
sure
the
stain.
dryer
as they are often flammable and highly poisonous.
use them in your washer as they may damage the paint or plastic components.
Some pretreatment sprays or liquids can damage your washer's control panel.
Take
as
reverse
treatments
Do not
Diaper Sanitizers
?
Diaper sanitizers are very corrosive to metal surfaces. DO NOT soak diapers in sanitizers in your
washer or tip the contents of the diaper bucket into your machine. Rinse and wring diapers out
thoroughly before placing them in your machine.
Diapers
?
Scrape off any excess baby cream, such as Vaseline from the diapers before washing
prevent the cream being transferred to other items in the wash.
to
and handwash
12
F
BeforStaingWsh
unction of each Button
Delay Start (Reservation)
?
button
delayed finishing time.
The time changes 6 E 9 E 15(6+9)
6hr when the button is pushed.
Use to set
Water level button
(indication of detergent amount)
a
E
?
adjust the water level as required. The appropriate
detergent is shown next to the water level in
the WATER-DETERGENT diagram
Water level is automatically selected for fuzzy (normal)
and jean programs.
The following settings are indicated as the button is
pushed LARGE E EX-LARGE E SMALL E
Use to
amount of
?
MEDIUM
Use to select
TURBO, WASH, RINSE
and SPIN functions
as
LARGE
Child lock function
Process button
?
E
desired.
Use to lock
or
unlock the control buttons to
prevent setting from being changed by a child.
To lock, push both the PROCESS, and
PROGRAM buttons simultaneously and to unlock
push them one more time during the washing
process.
(refer
Note
The control
panel may differ according to
different models
to p
18)
13
Use for
?
AUTO OFF
button
Program
?
selecting wash program.
This button allows you to select 4
different programs for different kinds of
?
laundry and dirtiness.
program selections light up in sequence as
follows: FUZZY (NORMAL) E
?
ECONOMY
E
JEAN
E
WOOL
?
?
(Power) button
Use to turn the power on or off.
Push again and power goes on or off
The power goes off automatically about 10
seconds after the wash is finished.
E
(NORMAL) etc. Select the
desired program by pressing the button.
FUZZY
AUTO OFF
Start/Pause button
?
?
?
Use to start
pause the
washing process.
by pushing the button.
The power goes off automatically 10 minutes after stopping.
This appliance is fitted with a safety function that automatically stops the
operation of the washing machine when it is exposed to heavy disturbance on
Repeats
or
start and pause
the mains.
:
3 step works at
large
and medium water level of
Fuzzy
and Jean program.
BeforStaingWsh
14
Washing Programs
WashingProm
Washing
Programs
Fuzzy Wash
(Normal Wash)
AUTO OFF
Add
the
Add
the detergent
laundry
1
2
4
Add the appropriate
quantity of detergent as
indicated by the water
level next to WATERDETERGENT.
Or follow the detergent
manufacturer's
instructions
Used for normal loads, this mode
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly
1
3
Economy Wash
Use this mode when washing lightly
5
2
Select the
ECONOMY
soiled clothes for a short time. The
weight should be under 2.0kg.
program on
the Control
panel.
Jean Wash
1
5
2
3
Use jeans program when
washing
heavy, thick, and extremely dirty
laundry such as jeans and work
Select the
JEAN
program on
the Control
outfits.
panel.
Wool Wash
Use this program for washing delicate
1
3
fabrics such
as lingerie and woolens.
(wash only "water washable" clothes)
Before washing your woolens check
the care label for the washing
5
2
Use neutral detergent
appropriate for the
laundry.
When washing
Select the
WOOL
program on
the Control
instructions.
woolens use a mild
panel.
detergent recommended for washing wool.
(wash only water washable clothes)
1
4
2
3
6
Turbo Wash
Use this mode to wash normal
clothes or thick and
which
are
heavy clothes
excessively dirty. Turbo
Fuzzy or
mode can be used with
Jean program.
The TURBO
will not work
in WOOL &
ECONOMY
program.
Select the
Turbo by
pressing the
Process
button.
TURBO
WASH
RINSE
SPIN
15
Close the lid
3
Caution & Note
Finish
5
6
If water is already in the tub, or putting wet
laundry into the tub before starting will
The pulsator rotates for 8
Water will be supplied
When the wash
increase the water level.
as
seconds to detect the
for 2 minutes after the
er
With
laundry load.
start of the wash to
program ends, the
buzzer will ring for 10
Rent
Then the water level and
supplement the water
the amount of detergent to
the laundry has
be used will be shown and
absorbed.
4
4
seconds before the
Power goes off
6
7
6
7
6
7
When
setting the water level manually, do not
prevent damage to laundry.
Washing with hot water may damage the
laundry (Water is set to cold automatically).
Ensure that the load is under 2kg
In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing may still
set to MEDIUM to
nt
nd-
contain some water. This is normal.
ol.
5
The water level and the
amount of detergent to be
used will be shown and
water will be supplied.
can
automatically.
water will be supplied.
4
lightweight bulky loads, water level
be set low.
7
8
WashingProm
16
D
AditonalFucOps
elay Start (Reservation) Wash
Delay Start (Reservation) Wash is used to delay the finishing time of the
The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time not the start time.
operation.
,
1
Press the POWER button to turn power
on.
AUTO OFF
2
Press the PROGRAM button to select the
washing program.
Select the program for laundry on the Control
This method will not work in Wool Program.
3
Delay Start (RESERVATION)
delayed washing is to be completed.
Press the
button to set the time when the
The time
DELA
STAR
4
Add the
detergent.
changes
6E 9E
The
panel.
as
following order
E
6Hours
.
appropriate quantity of detergent marked next to
water level of
the
WATER-DETERGENT.
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid
5
Add the
laundry
and press the START/PAUSE button.
When you press the START/PAUSE button the
blink.
6
an
supplied for 2 minutes after the start of the
supplement the water the laundry has absorbed.
Close the lid.
Water will be
Finish
The
wash to
light will
washing will be finished according to
the
delayed time.
Note
If the lid is open, the machine will not
work, and
an
alarm
signal will alarm to remind you
to close the
washing program, spinning time, water level or hot/cold manually, press the Delay Start
(RESERVATION) button and select the desired option. Then press the START/PAUSE button.
To select
laundry cannot be taken out immediately after the wash program ends, it is better to omit the
spinning program (The laundry will be wrinkled if left for a long time after spinning.)
When the
.
lid.
17
Option Washing
When you only need the Wash, Wash/Rinse, Rinse,
be set manually as follows.
1
Press the AUTO OFF
Rinse/Spin
button to turn power
(Power)
or
Spin cycle,
this can
on.
AUTO OFF
2
Wash
,
Wash+Rinse
,
Rinse
Rinse+Spin
,
,
Press the PROCESS button until above
light is on. ( refer to p13)
Spin only options
Option Washing
When you want to only drain, wait until the water in the
washing tub drains completely and then, turn off the
power.
3
Press the WATER LEVEL button, to control the water level according to the
laundry. If you do not choose anything, it is set the LARGE water
level automatically.
(refer to p12)
amount of
4
Add the
5
Press the START/PAUSE button.
6
Add the
laundry
into the
detergent
washing
tub.
and close the lid.
Note
?
When
a
Wash, Wash/Rinse or Rinse only option is selected,
after the wash is
completed the water will
drained off, If you wish to drain the water, press the SPIN button and wait until the water in the tub
has drained completely. Then press the START/PAUSE button
not be
.
?
?
?
If you do not
specify
If only Rinse is
It is
the water level, then Medium will be
selected, the process will
designed that fabric
softener be
start from Water
automatically selected.
Supply.
manually put before final rinse in wash option mode.
AditonalFucOps
18
O
AditonalFucOps
ther Useful Functions
Child Lock Function
If you want to lock all the
use
the child lock
keys to prevent all the setting from being changed by
a
child,
you
can
option.
How to Lock
1
Press the POWER button.
Turn Power
on.
AUTO OFF
2
Press the START/PAUSE button to start
washing.
After all
3
washing conditions
are
set
Press both the PROCESS button and the PROGRAM button
according to the manual.
simultaneously.
During the wash program, all the buttons are locked
until washing is completed or it is child- lock
function is deactivated manually.
How to Unlock
If you want to unlock
during wash, press both the PROCESS
and the PROGRAM button
simultaneously
again.
Note
In child-Lock
Mute
mode, all process light will blink.
Option
If you want to
use
the
washing machine
without alarm
signal sounds, press both the
WATER LEVEL and
PROCESS buttons simultaneously.
To make buzzer
time.
work, press both the WATER LEVEL and PROCESS buttons simultaneously one more
19
and
Placing
1
Leveling
Place the machine
on a
flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2cm right
side and left sides of the machine for ease of
more
than 10cm
installation.
At the rear,
a
minimum clearance of 10cm is
more
than
suggested.
2cm
more
than
2cm
2
Check that the machine is level
Open the lid
same as
and look from above to
see
Top
view of the machine
if it is
shown.
3 Leveling
the machine
Lift the front of the
washing machine and twist
Adjustable Leg
washing machine is
placed evenly.
until the
the
Adjustable legs
Installing the Anti-Rat Cover (option)
The anti-rat cover should be affixed
firmly from the back of the washer
Caution
If the power is supplied from a cord extension set
outlet device should be positioned so that it is hot
or
generator, the cord extension
set
or
electrical
exposed to splashing or ingress of moisture.
portable
Instal ion
20C
Instal ion
onnecting
Supply Hose
?Before connecting the Water Supply Hose to the water tap, check the hose type and then choose
the correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country, Make sure to
connect the blue inlet hose to the cold water tap, and the orange inlet hose to the hot water tap.
?Washing machine is to be connected to the water mains using new hose sets and that old hose
sets should not be reused.
Connecting
Water
Normal
1
Water
Supply
Hose to water
Type
Untighten
the
(Normal tap without thread &
Fixing
screw
type inlet hose.)
Rubber
screw
Untighten the screw of the connector so
tap can be placed in the middle.
2
tap
packing
that the
screw
Connector
the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4
3
screws.
Attach the water
to the connector
Push the water
supply
hose connects
supply hose vertically upwards
that the rubber seal within the hose
can
securely
Connector
so
adhere
completely to the tap.
Water
Supply
4
Fixing
the connector of connector and water
supply
hose
Attach the water
then
5
supply hose to the connector and
tighten it by screwing it to the right.
Check the connection of water
After
supply
connecting the hose, open the tap to check
for any water leakage.
In case of water leakage, close the tap and start
again from step
1
hose and the connector
Hose
21
Normal
1
Type
Separate
(Normal tap without thread & one touch type inlet hose.)
Middle connector from Water
Supply
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose while pressing them.
Hose
Middle
Fixed Sticker
connector
Pressing
Handle
Pressing
Rod
Water
2
Supply
Hose
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
Rubber
packing
screw
Fixed sticker
Note
In
case
the tap is too
large.
Guide
plate
Rubber
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate.
3
Then follow
packing
step1.
Fixing Connectors to
the
Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
4
Fixing Upper Connector
and Middle Connector
Remove the fixed sticker in between the
Connector
Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
5
Connecting
Middle
Connector
Fixed sticker
Middle Connector and Water
Supply
pressing rod of the Water Supply
separated from middle connector
and
then join it to the middle
Step1)
Connector
Middle
Connector
Hose
Press down the
Hose which
(refer to
was
Pressing
rod
connector.
Water
6
Check for water
After
leakage
the
hose, open the tap to check
connecting
for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
skip step 1, water leakage may occur.
If you
Supply
Hose
Pressing
handle
Instal ion
22
C
Instal ion
onnecting
Screw
1
Water
Supply Hose
Type
Attach the water
hose to the tap.
supply
Push the water supply hose up so that the rubber
packing within the hose can adhere completely to
the tap.
Water
tap
Rubber
Water
2
Connect the water
supply
Packing
Supply
hose to the tap.
Connect the water
tighten it by
3
supply hose to the tap and then
screwing it to the right.
Check water
leakage.
After
connecting the hose, open the tap to
for any water leakage.
Connecting
Water
Supply
Connect the water
the
check
Hose to the machine
supply hose to
inlet valve of
and then lock it by
washing machine,
connecting part.
turning
the hose
Check
to
see
if there is
the connector.
a
rubber seal inside
Hose connector
Rubber seal
Hose
23
Connecting
Drain Hose
Before connecting Drain Hose, check your Drain Hose model and choose
the correct instructions.
Pump
Instal ion
Model
1
Fit the machine end of the drain hose to the outlet
2
Put the other end of the drain hose over the
of the drain pump and
tighten the clamp.
standpipe or
wash tub.
Hose
Guide
Within 50mm
0.9~1.2m
Drain Hose
Note
To prevent siphoning, the drain hose should not extend more than 50mm from the end of the hose
The discharge height should be approximately 0.9
1.2m from the floor.
~
Non-Pump
1
Before
Model
connecting
Ensure that the hose
clip
is set
as
indicated here.
Clip
2
Connect the Elbow Hose
Push the elbow hose toward the
body of the
washing machine.
3
Place the Drain Hose
change the direction of the hose, pull out the
change the direction.
Repeat Step2.
To
elbow hose and
guide.
24
G
CarendMitc
rounding
Method
Earth wire should be connected.
If the earth wire is not connected, there is
caused by the current leakage.
Grounding
possible
a
danger of
electric shock
Method with Ground insert space Terminal
If the AC current outlet has
ground terminal, then
separate grounding
required. Note that AC
outlet
power
configurations may differ from country
a
is not
to
Ground Terminal
country
Outlet with
Other
Grounding
Method
Burying Copper
bury it
more
terminal.
Plate
Connect the Ground Wire
Plate and
ground
to
a
Ground
Copper
ground.
than 75cm in the
Ground Wire
75cm
Using Ground
Ground
Wire
Copper
ground Wire to the socket provided
exclusively for Grounding.
Plate
Connect the
Using Short Circuit
Ground
Wire
Breaker
If grounding methods described above are not
possible, a separate circuit breaker should be
employed and installed by a qualified electrician
Short-circuit
breaker
Caution
?
?
To prevent a possible explosion, do not connect ground to a gas pipe
Do not connect ground to telephone wires or lightning rods. This may be
storms
?
Connecting ground to plastic has no
?
Ground wires should be connected when
effect
an
extension cord is used.
dangerous during electrical
25
Cleaning
supply into the tub is not clean or the filter is clogged with
particles(Such
sand), clean the filter in the inlet valve occasionally.(The figure of
power cord and water tap may vary according to the country)
When water
as
To Clean the Filter in the Inlet Valve
Close the tap before
1
turning off the
water from the machine
removing the water
supply hose pull out the filter.
Then
use a
pulling out the cord.
completely.
After
3
Turn off the power before
2
power.
Select both hot/cold and then press the
[START/PAUSE] button to remove
4
Replace the filter after cleaning it.
brush to clean
the filter.
Caution
?
Before
cleaning the filter, the impurities in the water supply hose
should be removed.
To Clean the Lint Filter
1
Pull out the lint filter from
2
Turn the net inside out
the tub in the direction
to clean the filter and
shown below.
rinse it with water.
3
Replace- the filter to the
original location. Push the
lip of the filter until a pop
sound is heard.
Note
?
If the lint filter is torn
To Clean the
1
damaged, purchase a new
one
from LG service center.
Pump casing (for pump model)
Unfasten 4
back
or
screws
of the
cover.
2
Turn the cap as shown in
diagram and unfasten it.
Remove
as
foreign objects
pin, button, coin, etc
3
fasten it.
such
(Bottom view)
(Bottom view)
Caution
?
Check if water leaks after
reassembling. (The
Rubber
Reassemble the cap to
the arrow direction and
ring
is in the
cap)
CarendMitc
26
C
CarendMitc
and Maintenance
leaning
When there is
?
?
?
a
fear of
freezing
Close the water taps and remove the Water Supply Hose.
Remove the water which remains in the water supply.
Lower the drain hose and drain the water in the bowl and the drain hose
by spinning.
If frozen
?
?
?
supply hose, and immerse it in hot water at approx.. 40˚C.
Pour approx.. 2 liters of hot water at approx.. 40˚C, into the bowl and let it stand for 10 minutes.
Connect the water supply hose to the water tap and confirm that the washing machine performs the
Remove the water
supply
and
Wash Inner-tub
drainage of water.
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
use a clean soft cloth dampened with liquid detergent, then rinse. (Do
the inner-tub
not use harsh or
Inlet Hoses
Hoses
connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
sharp objects.
Exterior
Long
gritty cleaners.)
Vacations
Be
sure
water
be below
supply
freezing.
surface with
is shut off at faucets. Drain all water from hoses if weather will
Scrud
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener comes into
contact with detergent. This build-up is not brought about by a fault in the machine. If scrud is allowed to build-up
in the machine it can result in stains on your clothes or an unpleasant smell in your washer.If you wish to use
fabric softener
we
If you wish to
fabric softener
use
recommend.
we
recommend:
?
Clean your machine regularly
Cold water washing increases the chance of this
intervals e.g. approx. every 5th wash.
?
Fabric softener of thinner
?
Cleaning
?
?
?
?
build-up occurring. We recommend a warm or hot wash at regular
consistency is less likely to leave residue on the dispenser and contribute to a build-up.
the inside of your washing machine
If you use fabric softener or do
the inside of your machine.
regular cold
water
Fill your machine with hot water. Add about two cups of
Select Wash
and operate.
it 2
cycle
Repeat
Stop the machine, open the lid, and leave it to
drain the machine and
or
After
?
We do not recommend that you wash clothes
soaking,
Products that
?
?
?
?
run
a
it is
important that you occasionally clean
powder detergent that contains phosphate.
3 times.
soak
overnight.
the machine
?
?
washing,
through a regular cycle.
during this procedure.
might damage your washing
machine
diaper sanitizer will cause damage to the paintwork and components of your washer.
Hydrocarbon solvents i.e. petrol, paint thinners and lacquer thinners, etc. can dissolve plastic and blister paint (Be careful
when washing garments stained with these solvents as they are flammable DO NOT put them in washer or dryer.)
Concentrated bleaches and
Some pretreatment sprays
or
liquids can damage your washer's control panel.
Use of dyes in your washer may cause staining of the plastic components. The dye will not damage the machine but we
suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in your washer.
Do not
use
your washer lid
as a
work surface.
27
Troubleshooting
Look for your problem below, then check the things we suggest. More often
than not, this will give you the answer to your problem. And you'll be able to
carry on without having to telephone your service center.
WASH PROBLEM
Symptom
Lint or residue
on clothes
Error
Check up
Message
Incorrect
sorting
Washing
too
long
?
?
Separate lint producers from lint collectors.
Wash small loads for
a
shorter time than
larger
loads.
Natural By-product
When Washing
Certain Items
Detergent
on
clothes
Black spots
clothes
on
Detergent
dissolving
not
Incorrect use of
fabric softener
?
any lint not removed
Use
warmer
water
Using the dryer should remove
by the washer.
temperature.
Try pre-dissolving the detergent in warm water
Try a liquid detergent.
?
?
?
Dye transfer
Some lint is normal.
?
When
filling dispenser,
Sort whites
or
splash or overfill.
directly on clothes.
do not
Never pour fabric softener
Pre-treat stain and rewash.
lightly colored items from dark
colors.
-
Not enough
detergent used
?
Wash and
dry non-colorfast clothes separately
Insufficient
detergent,
clothes,
result in black marks
can
for the amount of soil
on
on
the
clothes
A
build-up caused
by the interaction
?
of fabric softener
and detergent can
flake off and marks
on clothes.
Fabric
damage
(Snags, holes,
tears, rips
excessive
or
wear)
Pins, snaps,
hooks, sharp
buttons, belt
buckles, zippers,
?
?
Cleaning the inside of your washing machine
(refer to p25, p26)
Fasten snaps, hooks, buttons, and zippers.
Remove any loose brassiere wires.
Remove
?
Turn knits
and sharp objects
left in pockets
Chemical Damage
a. Chlorine Bleach
b. Battery Acid
c.
Hydrogen
Peroxide
objects in pockets and sharp buttons.
(which snag easily) inside out.
?
?
Dilute bleach
?
Use caution around
products
tears
-
or use
these
in fabrics.
the dispenser (See User's Guide)
battery acids, skin and hair care
can remove
color and
cause
holes
or
Troubleshting
28
T roubleshooting
Troubleshting
Symptom
Error
Message
Non-chemical
Damage
a. Age &
Check up
?
Check construction
carefully when purchasing
damage before laundering
?
Mend any
Water temperature
is too cold.
?
Use
Water temperature
is not correct
?
Select the wash temperature
?
For
Normal Use
b. Poor Construction
c.
Overloading
d. Mice & Inserts
e.
The
laundry
out dirty
comes
Sunlight
warmer
water
example,
temperature
according to
blood and mud
cold water, while
are
soil type.
better washed in
oily soils wash better in warmer
water.
Stain is not pretreated
?
Incorrect
sorting
?
?
?
Insufficient
a
little
stains like collars and cuffs to
?
Washer is
overloaded
detergent dissolved in water onto
help shift dirt.
Wash stains as soon as possible. The longer they are
left the harder they are to remove.
Brush
?
Did you load too much into the machine?
White clothes
are better washed separately.
Separate light and heavily soiled items, as clothes
can pick up soil from dirty wash water.
Loads made up of articles of varying sizes will
wash better (e.g. full loads of sheets may not wash
that
well).
Not
enough detergent for load size or amount of
requires more detergent than soft
soil. Hard water
detergent
water.
Pilling
Result of normal
wear on
poly-
cotton blends and
fuzzy
Grayed or
yellowed
clothes
fabrics
?
While this is not caused
can
slow the
by the washer, you
pilling process by washing
garments inside
detergent (especially with larger loads).
Not
enough
detergent
Use
Water is not hot
Make
enough
120F~40F.(48˚C
Washer is
overloaded
Select load size
Dye transfer
Sort clothes
more
out.
sure
water heater is
delivering water at
60˚C.).
~
to match clothes load.
by color. If fabric label states wash
separately,unstable dyes may be indicated.
29
Troubleshooting
Before
calling for
Error
Symptom
Water
Supply
service check the
Failure
problem against
Message
Troubleshting
Check up
TURBO
.
WASH
.
RINSE
the list below.
.
SPIN
.
.
Is the water tap shut off?
Is the water supply cut off ?
Is the tap
or
water
supply hose frozen
?
Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
Is Hot/Cold selected to Hot when the hose connected
is Cold?
.
Drainage
Failure
.
Is the drain hose
.
Is the drain hose bent
.
Is the internal part of the hose
TURBO
WASH
RINSE
SPIN
Failure
TURBO
or
drain pump
Check if electric power has gone off.
.
Is the
laundry evenly balanced?
.
Is the
washing machine placed on
.
Is the lid closed?
.
Ask for
WASH
RINSE
SPIN
Door(Lid) Open
positioned correctly?
or placed too high?
(only pump model) clogged with impurities?
.
Spin
Is the Cold hose connected to Hot?
TURBO
a
flat surface?
WASH
RINSE
SPIN
Internal sensing
failure
Power failure
Overflow failure
help
at the
LG Electronic branch
of the Service Center
30
T
erms
of
Warranty
What Is Not Covered:
?
?
?
If the
product is
connected to any
voltage other than that shown on the rating plate.
If the fault is caused by accident, neglect, misuse or Act of God.
If the fault is caused by factors other than normal domestic use or use in
accordance with the owner's manual.
?
?
?
?
?
?
?
?
?
Provide instruction
change the set-up of the product.
If the fault is caused by pests for example, rats or cockroaches etc..
Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
Correcting the installation for example, levelling the product, adjustment of drain.
Normal maintenance which recommended by the owner's manual.
Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
Replace fuses in or correct house wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects
with this appliance.
If the
on use
of product
or
product is installed outside the normal service area, any cost of transportation
involved in the repair of the product, or the replacement of a defective part, shall be
borne by the owner.
31
Specification
H
D
W
Model
WF-F(C/S) 5101(~5),5111(~5),5121(~5) PC(D/M)(X/K)
WF-F(C/S) 5201(~7),5211(~7),5221(~7) PC(D/M)(X/K)
WF-F(C/S) 5401(~5),5411(~5),5421(~5) TC(D/M)(X/K)
WF-F(C/S) 5700, 5710,
5720
PC(D/M)(X/K)
WF-F(C/S) 6101(~5),6111(~5),6121(~5) TC(D/M)(X/K)
WF-F(C/S) 6201(~7),6211(~7),6221(~7) TC(D/M)(X/K)
WF-F(C/S) 6700, 6710,
6720
TC(D/M)(X/K)
WF-F60PC, WF-F63PC
WF-F(C/S) 5101(~5),5121(~5),5401(~5),
Size
540(W)x540(D)x850(H)
5421(~5),6101(~5),6121(~5)
WF-F(C/S) 5111(~5),5411(~5),6111(~5)
WF-F(C/S) 5201(~7),5221(~7),5700,
5720
540(W)x540(D)x890(H)
530(W)x540(D)x850(H)
6201(~7),6221(~7),6700, 6720
WF-F60PC, WF-F63PC
WF-F(C/S) 5211(~7),6211(~7),6710
Water tab pressure
In
30 -800 kPa (0.3 -8
kgf /cm2)
continuing effort to improve the quality of our appliances,
changes to the appliance without revising this manual.
our
530(W)x540(D)x900(H)
it may be necessary to make
P/No.: 3828EA3011Q
Download PDF

advertising