LG | WF-F5207PC | LG WF-F5207PC Owner’s Manual

Washing
Machine
OWNER'S MANUAL
MODELS
:
WF-S(C/F)5101(~5)PC(H/P),S(C/F)5101(~5)PD(E/F)
WF-S(C/F)5111(~5)PC(H/P),S(C/F)5111(~5)PD(E/F)
WF-S(C/F)5201(~7)PC(H/P),S(C/F)5201(~7)PD(E/F)
WF-S(C/F)5211(~7)PC(H/P),S(C/F)5211(~7)PD(E/F)
WF-S(C/F)6101(~5)TC(H/P),S(C/F)6101(~5)TD(E/F)
WF-S(C/F)6111(~5)TC(H/P),S(C/F)6111(~5)TD(E/F)
WF-S(C/F)6201(~7)TC(H/P),S(C/F)6201(~7)TD(E/F)
WF-S(C/F)6211(~7)TC(H/P),S(C/F)6211(~7)TD(E/F)
WF-S(C/F)5301(~7)TC(H/P),S(C/F)5311(~7)TD(E/F)
WF-S(C/F)5401(~5)TC(H/P),S(C/F)5411(~5)TD(E/F)
Please read this manual
carefully
before
operating your
set.
Retain it for future reference.
Record model
name
and serial number of the set.
Quote this information to your dealer when you require service.
P
roduct Features
Fuzzy Logic Control
A built-in load
automatically detects and measures the laundry load and
a microprocessor optimizes washing conditions such as ideal water level and
washing time.
sensor
Advanced
the best
technology is built
washing result.
into the Electronic Control
SENSING
START
Laundry
Sensor
Water Level Sensor
3
System
which
SETTING
Optimum
Washing
Condition
WASHING
ensures
AUTO
POWER
OFF
Step washing
3 sept
washing
makes best
washing
effect with low
tangling.
Rubbing and
Shaking
Rubbing
Shaking and
Disentangling
Lint Filter
Lint and loose threads from
during
for
a
the
washing cycle
laundry generated
caught by the lint
are
filter
cleaner wash.
Auto Restart
In the event of
power failure, the washing machine will
start its interrupted cycle when power is resumed.
※
Applied
a
models
:
automatically
WF-S(C/F)5101(~5)PD(E/F),S(C/F)5111(~5)PD(E/F)
WF-S(C/F)5201(~7)PD(E/F),S(C/F)5211(~7)PD(E/F)
WF-S(C/F)6101(~5)TD(E/F),S(C/F)6111(~5)TD(E/F)
WF-S(C/F)6201(~7)TD(E/F),S(C/F)6211(~7)TD(E/F)
WF-S(C/F)5301(~7)TD(E/F),S(C/F)5311(~7)TD(E/F)
WF-S(C/F)5401(~5)TD(E/F),S(C/F)5411(~5)TD(E/F)
C
ontents
Read this manual
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
in the
Troubleshooting
section. If you review
our
chart of
Troubleshooting Tips first,
you
may not need to call for service at all.
Introduction
Before
Starting
Safety
to Wash
information
4
Identification of Parts
5
Function Information
6
Preparation Before Washing
7
Use of Water,
8
Detergent,
Bleach
and Softener
Function of each Button
Washing Programs
Fuzzy
Wash
Economy
Additional Function
Options
Installation
Care and Maintenance
10
(Normal Wash)
Wash
12
12
Jean Wash
12
Wool Wash
12
Soak Wash
12
Delay Start (Reservation)
Wash
14
Option Washing
15
Other useful Functions
16
Placing
and
Connecting
Water
Connecting
Drain Hose
Grounding
17
Leveling
Supply
Method
Hose
18
21
22
Cleaning
23
Troubleshooting
Troubleshooting
25
Specification
Specification
27
4
S
afety
information
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Introducin
For your better understanding, these precautions are separated into two categories.
We urge you to pay special attention to them in the interests of your own safety, and
machine
Violation of these
Attention
Following
these
guidelines
guidelines
could result in serious
The
is not intended for
use
infirm persons without
Supply
to
sure
to
two persons should move it.
Do not install the washer where it is
exposed to sunlight, wind, rain, etc.
The appliance must be positioned so that
the plug is accessible
ground the earth wire or connect it
Make
sure
ground detector after you put the power cord
into an outlet.
not move.
When the power cord is loose, do not use it.
Do not damage the power cords.
hands.
one
feet under this
place any rugs or heavy material
the power cord.
Since the machine is heavy, a minimum of
and
a
Do not plug many cords into
time.
or
over
Young children should be supervised to ensure that
they do not play with the appliance.
The base opening must not be obstructed by
carpeting when the washing machine is installed on
a carpeted floor.
Make
against damage.
Do not
source.
Power
injury.
Do not put your hands
machine.
by young
supervision.
Do not install the washing machine in a damp place.
Keep the washing machine away from fire or heat
or
fatal
Attention
appliance
children
or
will protect your machine
Caution
cord
protection of your
against damage:
Caution
Installation
or
plug
the power cord is free of dust
properly so that the cord will
it in
Do not touch the power cord with wet
outlet at the
same
If the power cord or fuse is damaged, it must be
replaced by the manufacturer or its service agents or
similarly qualified people in order to avoid a hazard.
If the appliance is supplied from a cord extension
set or electrical portable outlet device the cord
extension set or electrical portable outlet device
should be positioned so it is not subject to splashing
or ingress of moisture.
Do not place any electric appliance with a charging
battery, magnetically-driven appliance and magnetic
body on the washer.
Operation
When you take out the
fall into the washer.
laundry, be careful not to
?
Do not put hands into the rotating tub.
Do not sprinkle water over the buttons.
Make
sure
the lid is closed
activating the machine.
more than 50˚C(122˚F)
?
Do not pour
into the tub.
?
Do not wash any
during operation of the
Do not put heavy objects on the machine.
Unplug the cord when the machine is not in
Do not press the buttons with sharp objects.
Check the hose connection and open the tap
before
spin cycle.
Maintenance
?
?
use.
?
water
waterproof materials.
Do not pour corrosive materials or bleach
over the washing machine. It will cause
damage to the power cord or the machine.
Never disassemble or remodel the washer
and power cord by yourself. Only a
qualified technician should work on the
machine.
5
dentification of Parts
I
Introducin
Body
*
Power cord
Water
supply hose(1
Powder
Bleach
detergent
EA
or
2EA)
*
box
dispenser
Inner tub
Control
*
panel
*
Lint filter
Drain hose
for pump model *
Pulsator
*
Adjustable leg
Drain hose for
non
pump model
Accessories
Water
supply
hoses
Drain hose
or
or
1 Each for cold and
hot water
Note
“
”Part can be different according
to the model.
Anti-rat
cover
(option)
*
6
Function
Information
Our machine provides various washing methods which suit various conditions and
types of laundry.
BeforStaingWsh
Different
types of laundry washing
Fuzzy
(Normal) Wash
Use this
Program for normal clothes except for woolen clothes and lingerie.
automatically detects the quantity of laundry and selects the appropriate
power, washing time, rinsing time and spinning time. (refer to p12 )
The
sensor
Economy
water
level, wash
Wash
Economy wash can be
selected to wash
lightly
soiled clothes of less than 2.0
kg in
a
short time.
(refer
to
p12)
Jean Wash
Thick and
(refer
to
heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed.
p12)
Wool Wash
Delicate clothes
(lingerie,
wool
etc.) which
may be
easily damaged can be washed. (refer
to
p12)
Soak Wash
Soak Wash
and
can
be selected to wash
grime. (refer
to
heavily
soiled
laundry by soaking in water for some time to remove dirt
p12)
Other washing methods
Delay Start (Reservation)
Wash
Delay Start (Reservation) Wash is used to delay the finishing time of the operation.
Delayed Start washing can be set according to preference. (refer to p14)
Option
Wash
Spin, Rinse/Spin, Rinse, Wash/Rinse,
and Wash
only options can selected. (refer
to
p15)
7
Before
Preparation
Washing
BeforStaingWsh
Sorting
results, different fabrics need to be washed in different ways.
Normal,
(Heavy,
Light)
Separate clothes according to amount of soil
COLOR (Whites, Lights, Darks)
Separate white fabrics from colored fabrics.
To get the best
SOIL
LINT
(Lint producers, Collectors)
Caring
?
before
Check all
such
as
Separate lint producers
and lint collectors.
loading
pockets to make sure that they are empty. Things
pens, coins and keys can damage
nails, hairclips, matches,
both your washer and your clothes.
?
Close
zippers, hook and strings to
don't snag
?
?
on
make
sure
that these items
other clothes.
Mend any torn garments or loose buttons. Tears
become larger during washing.
Remove any loose brassiere wires
and clothes.
as
or
holes may
they can damage your
washing machine
?
Pre-treat dirt and stains.
?
Make
?
Check the
sure
the clothes
are
WIRE
washable in water.
washing instructions.
Pretreatment
detergent dissolved in water onto stains like collars
help shift dirt.
Treat stains AS SOON AS POSSIBLE. The longer they are left the
harder they are to remove.
Brush
a
little
and cuffs to
Light
and
Large-size clothing
Clothes like downs and woollens
Long laundry
net and
are
light weight, large and float
wash them in
a small amount of water.
easily.So
nylon
If the laundry floats during the wash cycle, it may become damaged.
Use dissolved detergent to prevent the detergent from clumping.
use a
items
nylon nets for long, delicate items.
laundry with long strings or long length, a net will prevent
tangling during washing.
Fasten zippers or hooks on items before washing.
※ Nylon net is not supplied by LG.
Use
For
8
Use
BeforStaingWsh
of Water,
Detergent,
Bleach and Softener
Using water
Amount of water
?
This machine detects the
quantity of laundry automatically,
then sets the water level and proper amount of detergent.
?
When you select a wash program, the water level and
amount of detergent (to be used) will be shown on the
control
?
panel.
When the water level is
though the
same
it may differ depending
the control panel.
automatically detected,
water level is indicated
on
on
the
quantity of laundry even
Water temperature
?
The machine sets the
?
You
can
appropriate temperature automatically according to the wash program
change the water temperature by pressing the WATER TEMP button.
to
(refer
Using Detergent and
Amount of
detergent
When you select a wash program, the water level and the amount of detergent will be
shown on the control panel. The amount of a cup in the diagram is about 40g for
?
For the correct amount of detergent, refer to
Available
?
?
p10)
Fabric Softener
?
concentrated
.
detergent.
detergent manufacturer's instruction
.
Detergent Type
Synthetic detergents that yield a low level of foam are recommended.
liquid detergent is used, mix it with water (1:1) and pour it into the bleach dispenser.
When
Attention
If excessive
pollution,
detergent is used, the rinse will not be as clean
it accordingly.
Available Fabric Softener
?
Do not
?
For
Also, it could cause environmental
Type
concentrated fabric softener. This may cause some problems in automatic
details refer to the softener products instructions for use.
use
more
and efficient.
so use
dispensing.
9
Depositing Detergent
Powder
Open the detergent dispenser and deposit the
appropriate amount of detergent
Detergent dispenser.
.
Where you
deposit the
detergent
Depositing
?
?
?
?
?
Fabric softener
Don't use softener with
rinse water
detergent.
When using dispenser, dilute
fresh water(30ml)
softener(30ml) with
When filling dispenser, do not
It may stain clothes.
Never pour fabric softener
It may stain them
Use softener in last
splash or overfill.
directly on clothes.
If
spotting occurs, wet and rub hand
dishwashing liquid (or mild bar soap)
and rewash.
Note
Fabric Softener will be inserted
Using
Bleach
Check fabric
care
Available Bleach
Use
automatically during the final rinse.
labels for
special instructions.
Type
oxygenated bleach.
Powdered bleach should mixed with water and then be
For
more
details refer to the
Depositing
products
deposited into the tub.
instruction for use.
Bleach
Separate the laundry to be bleached and deposit
liquid bleach into the Bleach dispenser.
The dispenser dilutes liquid chlorine bleach before
Bleach
dispenser
it reaches into your wash load.
Attention
Do not insert bleach
or
fabric softener
directly onto laundry. This may affect colors or damage clothing
or acids such as vinegar and/or rust remover. Mixing can
Do not mix chlorine bleach with ammonia
produce a toxic
gas which may
cause
death.
BeforStaingWsh
10
F
BeforStaingWsh
unction of each Button
Water
?
temperature button (option)
(indication of detergent amount)
Use to select water temperature.
Pressing the button allows you to select
Cold
Warm
Cold
respectively.
(Hot&Cold)
Default
Water level button
?
Hot
adjust the water level as required. The appropriate
detergent is shown next to the water level in
the WATER-DETERGENT diagram
Water level is automatically selected for fuzzy (normal)
and jean programs.
The following settings are indicated as the button is
EX-LARGE
SMALL
pushed LARGE
Use to
amount of
setting is Cold.
?
MEDIUM
LARGE
Process button
?
Use to select
desired.
Note
The control
panel may differ according to
different models
SOAK, WASH, RINSE
and SPIN functions
as
11
Program
?
?
Use for
selecting wash program.
This button allows you to select 4
different programs for different kinds of
laundry
?
Start/ Pause button
button
follows: FUZZY
ECONOMY
?
light up in sequence as
or
WOOL
unlock the control
buttons to prevent
setting from
being changed by a child.
To lock, push the PROCESS, and
PROGRAM buttons simultaneously
and to unlock push them one more
time during the washing process.
(refer to p 16)
Repeats
washing process.
by pushing the
The power goes off automatically 10
minutes after stopping.
appliance is fitted with a safety
automatically stops the
of
the
operation
washing machine when
it is exposed to heavy disturbance on the
(NORMAL) etc. Select the
desired program by pressing the button.
Use to lock
pause the
function that
FUZZY
Child lock function
or
start and pause
※ This
(NORMAL)
JEAN
Use to start
button.
?
and dirtiness.
program selections
?
mains.
Delay Start (Reservation)
?
button
delayed finishing time.
changes 6→9→15(6+9)→6hr
when the button is pushed.
Use to set
a
The time
(refer
to
p14)
BeforStaingWsh
12
Washing Programs
WashingProm
Washing
Programs
AUTO POWER OFF
Add
the
Add
the detergent
laundry
Fuzzy Washing
(Normal Wash)
1
2
4
・Add the appropriate
quantity of detergent as
indicated by the water
level next to WATERDETERGENT.
Or follow the detergent
manufacturer's
instructions
Used for normal loads, this mode
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly
1
3
Economy Wash
Use this mode when washing lightly
solided clothes for
a short
2
5
・Select the
ECONOMY
time. The
weight should be under 2.0kg.
program on
the Control
panel.
Jean Wash
1
5
2
3
Use jeans program when
washing
heavy, thick, and extremely dirty
laundry such as jeans and work
・Select the
JEAN
program on
the Control
outfits.
panel.
Wool Wash
Use this program for washing delicate
fabrics such
1
3
lingerie and woolens.
(wash only
clothes)
Before washing your woolens check
the care label for the washing
as
・Use neutral
detergent
appropriate for the
laundry.
・When washing
・Select the
"water washable"
WOOL
program on
the Control
instructions.
(wash
5
2
woolens use a mild
panel.
detergent recommended for washing wool.
only water washable clothes)
Soak Wash
1
Use this mode for washing
excessively dirty laundry by soaking
in water for some time to
remove
proteins and fats. 'SOAK' mode can
be used with all washing programs
simultaneously except for "WOOL"
program.
4
2
3
・The SOAK
will not work
in WOOL
Program.
・Keep pressing the PROCESS button until the SOAK light is on and then WASH,
RINSE, SPIN lights are on simultaneously.
・If necessary, select the desired washing process from
(SOAK+WASH+RINSE+SPIN), (SOAK+WASH+RINSE),
(SOAK+WASH) manually.
6
13
Close the lid
3
4
・The pulsator rotates for 8
for 2 minutes after the
laundry load.
program ends, the
start of the wash to
buzzer will
ring for 10
supplement the water
seconds before the
the amount of detergent to
the laundry has
be used will be shown and
Power goes off
absorbed.
automatically.
water will be supplied.
5
・When the wash
seconds to detect the
・Then the water level and
5
6
5
・Water will be supplied
Caution & Note
Finish
4
4
6
7
6
7
・If water is already in the tub,
or putting wet
laundry into the tub before starting will
increase the water level.
・With
lightweight bulky loads, water level
・Changes to water temperature (hot/cold) and
wash level are possible during operation.
(refer to p 10)
・When setting the water level
set to MEDIUM to
5
4
6
7
detergent
for the
ing
a
manually, do not
prevent damage to
laundry.
・Washing with hot water may damage the
laundry (Water is set to cold automatically).
Ensure that the load is under 2kg
・In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing may
still contain some water. This is normal.
mild
・Soak Wash cannot be selected for the Wool
commend-
Wash program.
ing wool.
6
can
be set low.
5
・The water level and the
amount of detergent to be
used will be shown and
water will be supplied.
7
8
WashingProm
14
Delay
AditonalFucOps
Start
(Reservation) Wash
Delay Start (Reservation) Wash is used to delay the finishing time of the
The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time not the start time.
operation.
,
1
Press the POWER button to turn power
on.
AUTO POWER OFF
2
Press the PROGRAM button to select the
washing program.
Select the program for laundry on the Control panel.
This method will not work in Wool Program.
3
Delay Start (RESERVATION)
delayed washing is to be completed.
Press the
button to set the time when the
The time
changes as following order
(6→9→15→ 6Hours).
4
Add the
The
detergent.
appropriate quantity of detergent marked next to the
water level of
WATER-DETERGENT.
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid
5
Add the
laundry
and press the START/PAUSE button.
When you press the START/PAUSE button the
blink.
6
an
supplied for 2 minutes after the start of the
supplement the water the laundry has absorbed.
Close the lid.
Water will be
Finish
The
wash to
light will
washing will be finished according to the delayed time.
Note
If the lid is open, the machine will not
To select
work, and
washing program, spinning time,
(RESERVATION)
When the
laundry
spinning program (The laundry
.
alarm
water level
button and select the desired
cannot be taken out
an
or
option.
signal will
alarm to remind you to close the lid.
hot/cold manually, press the Delay Start
Then press the START/PAUSE button.
immediately after the wash program ends, it is better to
a long time after spinning.)
will be wrinkled if left for
omit the
15
Option Washing
When you
1
only
need the Wash, Wash/Rinse
Press the AUTO OFF
(Power)
or
Rinse
these
cycles,
button to turn power
can
be set
manually
on.
AUTO POWER OFF
2
Wash
,
Wash+Rinse
,
Rinse
Rinse+Spin
,
,
Press the PROCESS button until above
light is on. ( refer to p11)
Spin only options
Option Washing
When you want to only drain, wait until the water in the
washing tub drains completely and then, turn off the
power.
3
Press the WATER LEVEL button, to control the water level according to the
laundry. If you do not choose anything, it is set the LARGE water
level automatically.
(refer to p10)
amount of
4
Add the
5
Press the START/PAUSE button.
6
Add the
laundry
into the
detergent
washing
tub.
and close the lid.
Note
?
When
a
Wash, Wash/Rinse or Rinse only option is selected,
after the wash is
completed the water will
drained off, If you wish to drain the water, press the SPIN button and wait until the water in the tub
has drained completely. Then press the START/PAUSE button
not be
.
?
?
If you do not
specify the water level, then Medium will be automatically
If only Rinse is
selected, the process will
start from Water
Supply.
selected.
AditonalFucOps
16
O
AditonalFucOps
ther Useful Functions
Child Lock Function
If you want to lock all the
use
the child lock
keys
to
prevent all the setting from being changed by
a
child,
you
can
option.
How to Lock
1
Press the POWER button.
Turn Power
on.
AUTO POWER OFF
2
Press the START/PAUSE button to start
washing.
After all
3
washing conditions
are
set
Press both the PROCESS button and the PROGRAM button
according to the manual.
simultaneously.
During the wash program, all the buttons are locked
until washing is completed or it is child- lock
function is deactivated manually.
How to Unlock
If you want to unlock
during wash, press both the PROCESS
and the PROGRAM button
simultaneously
again.
Note
In child-Lock
Mute
mode, all process light will blink.
Option
If you want to
use
the
washing machine
without alarm
signal sounds, press both the
WATER LEVEL and
PROCESS buttons simultaneously.
To make buzzer
time.
work, press both the WATER LEVEL and PROCESS buttons simultaneously one
more
17
and
Placing
1
Leveling
Place the machine
on a
flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2cm right
side and left sides of the machine for ease of
more
than 10cm
installation.
At the rear,
a
minimum clearance of 10cm is
more
than
suggested.
2cm
more
than
2cm
2
Check that the machine is level
Open the lid and look from above to
same as
see
Top
view of the machine
if it is
shown.
3 Leveling
the machine
Lift the front of the
washing machine and twist
Adjustable Leg
washing machine is
placed evenly.
until the
the
Adjustable legs
※
Installing the Anti-Rat Cover (option)
The anti-rat cover should be affixed
firmly from the back of the washer
UP
Caution
If the power is supplied from a cord extension set
outlet device should be positioned so that it is hot
or
generator, the cord extension
set
or
electrical
exposed to splashing or ingress of moisture.
portable
Introducin
18C
onnecting
Before
Water
connecting
the Water
sure
tap, check the hose type and
Connecting
Supply
Hose
supplied may vary from country to country, Make
tap, and the orange inlet hose to
to connect the blue inlet hose to the cold water
the hot water
Water
Normal
1
Hose to the water
Supply
then choose the correct instruction here under.
Note that the Water
Instal ion
Hose
Supply
tap
Supply
Hose to water
Type
Untighten
the
tap
(Normal tap without thread &
screw
type inlet hose.)
Rubber
screw
packing
Untighten the screw of the connector so that the
tap can be placed in the middle.
2
Fixing
screw
Connector
the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
3
Attach the water
to the connector
Push the water
supply
hose connects
supply hose vertically upwards
that the rubber seal within the hose
can
securely
Connector
so
adhere
completely to the tap.
Water
Supply
4
Fixing
the connector of connector and water
supply
hose
Attach the water
then
5
supply hose to the connector and
tighten it by screwing it to the right.
Check the connection of water
After
supply
connecting the hose, open the tap to check
for any water leakage.
In case of water leakage, close the tap and start
again from step
1
hose and the connector
Hose
19
Normal
1
Type
Separate
(Normal tap without thread &
Middle connector from Water
Supply
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose while pressing them.
one
touch type inlet hose.)
Hose
Middle
Fixed Sticker
connector
Pressing
Handle
Pressing
Rod
Water
2
Supply
Hose
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
Rubber
packing
screw
Fixed sticker
Note
In
case
the tap is too
large.
Guide
plate
Rubber
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate.
3
Then follow
packing
step1.
Fixing Connectors to
the
Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
4
Fixing Upper Connector
and Middle Connector
Remove the fixed sticker in between the
Connector
Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
5
Connecting
Middle
Connector
Fixed sticker
Middle Connector and Water
Supply
pressing rod of the Water Supply
separated from middle connector
and
then join it to the middle
Step1)
Connector
Middle
Connector
Hose
Press down the
Hose which
(refer to
was
Pressing
rod
connector.
Water
6
Check for water
After
leakage
the
hose, open the tap to check
connecting
for any water leakage.
If the connection leaks, close the tap and start
again from step 1.
skip step 1, water leakage may occur.
If you
Supply
Hose
Pressing
handle
Instal ion
20
C
Instal ion
onnecting
Screw
1
Water
Supply
Hose
Type
Attach the water
supply
hose to the tap.
Push the water supply hose up so that the rubber
packing within the hose can adhere completely to
the tap.
Water
tap
Rubber
Water
2
Connect the water
supply
Packing
Supply
hose to the tap.
Connect the water
tighten it by
supply hose to the tap and then
screwing it to the right.
3
Check water
leakage.
After
connecting the hose,
for any water leakage.
Connecting
Water
Supply
open the tap to check
Hose to the machine
supply hose to inlet valve of
washing machine, and then lock it by turning
the hose connecting part.
Connect the water
the
Check
to
see
if there is
the connector.
a
rubber seal inside
Hose connector
Rubber seal
Hose
21
Connecting
Drain Hose
Before connecting Drain Hose, check your Drain Hose model and choose
the correct instructions.
Pump
Instal ion
Model
1
Fit the machine end of the drain hose to the outlet
2
Put the other end of the drain hose over the
of the drain pump and
tighten the clamp.
standpipe or
wash tub.
Hose
Guide
Within 50mm
0.9~1.2m
Drain Hose
Note
To prevent siphoning, the drain hose should not extend more than 50mm from the end of the hose
The discharge height should be approximately 0.9
1.2m from the floor.
~
Non-Pump
1
Before
Model
connecting
Ensure that the hose
clip
is set
as
indicated here.
Clip
2
Connect the Elbow Hose
Push the elbow hose toward the
body of the
washing machine.
3
Place the Drain Hose
change the direction of the hose, pull out the
change the direction.
Repeat Step2.
To
elbow hose and
guide.
22
G
CarendMitc
rounding
Method
Earth wire should be connected.
If the earth wire is not connected, there is
caused by the current leakage.
Grounding
possible
a
danger of
electric shock
Method with Ground insert space Terminal
If the AC current outlet has
ground terminal, then
separate grounding
required. Note that AC
outlet
power
configurations may differ from country
a
is not
to
Ground Terminal
country
Outlet with
Other
Grounding
Method
Burying Copper
bury it
more
terminal.
Plate
Connect the Ground Wire
Plate and
ground
to
a
Ground
Copper
ground.
than 75cm in the
Ground Wire
75cm
Using Ground
Ground
Wire
Copper
ground Wire to the socket provided
exclusively for Grounding.
Plate
Connect the
Using Short Circuit
Ground
Wire
Breaker
If grounding methods described above are not
possible, a separate circuit breaker should be
employed and installed by a qualified electrician
Short-circuit
breaker
Caution
?
?
To prevent a possible explosion, do not connect ground to a gas pipe
Do not connect ground to telephone wires or lightning rods. This may be
storms
?
Connecting ground to plastic has
?
Ground wires should be connected when
no
effect
an
extension cord is used.
dangerous during electrical
23
Cleaning
supply into the tub is not clean or the filter is clogged with
particles(Such
sand), clean the filter in the inlet valve occasionally.(The figure of
power cord and water tap may vary according to the country)
When water
as
To Clean the Filter in the Inlet Valve
Close the tap before
1
turning off the
water from the machine
removing the water
supply hose pull out the filter.
Then
use a
pulling out the cord.
completely.
After
3
Turn off the power before
2
power.
Select both hot/cold and then press the
[START/PAUSE] button to remove
4
Replace the filter after cleaning it.
brush to clean
the filter.
Caution
?
Before
cleaning the filter, the impurities in the water supply hose should be removed.
To Clean the Lint Filter
1
Pull out the lint filter from
2
Turn the net inside out
the tub in the direction
to clean the filter and
shown below.
rinse it with water.
3
Replace- the filter to the
original location. Push the
lip of the filter until a pop
sound is heard.
Note
?
If the lint filter is torn
To Clean the
1
damaged, purchase
a new one
from LG service center.
Pump casing (for pump model)
Unfasten 4
back
or
screws
of the
cover.
2
Turn the cap as shown in
diagram and unfasten it.
Remove
as
foreign objects
pin, button, coin, etc
3
fasten it.
such
(Bottom view)
(Bottom view)
Caution
?
Check if water leaks after
reassembling. (The
Rubber
Reassemble the cap to
the arrow direction and
ring
is in the
cap)
CarendMitc
24
C leaning
CarendMitc
WHEN THERE IS A FEAR OF FREEZING
1
Close the water taps and
2
Remove the water which remains in the water
3
Lower the drain hose and drain the water in the bowl and the drain hose
remove
the Water
Supply Hose.
supply.
by spinning.
IF FROZEN
and immerse it in hot water at approx.. 40 ˚C.
1
Remove the water
2
Pour approx.. 2 liters of hot water at approx.. 40
3
Connect the water
supply
and
supply hose,
supply hose to
drainage of water.
Wash Inner-tub
˚C, into
the bowl and let it stand for 10 minutes.
the water tap and confirm that the
washing machine performs
the
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
use a clean soft cloth dampened with liquid detergent, then rinse. (Do
the inner-tub
not use harsh or
Inlet Hoses
Hoses
connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
sharp objects.
Exterior
Long
gritty cleaners.)
Vacations
Be
sure
water
be below
supply
freezing.
surface with
is shut off at faucets. Drain all water from hoses if weather will
SCRUD
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
into contact with detergent. This build-up is not brought about by a fault in the machine.
comes
If scrud is allowed to
build-up in the machine it
smell in your washer.
unpleasant
If you wish to
?
?
?
?
Using fabric
Clean
fabric softener
use
the
dispenser,
dispenser as
soon as
do not
the
we
can
result in stains
on
your clothes
or an
recommend.
splash or overfill.
cycle has finished.
Clean your machine
Cold water
regularly
washing increases the chance of this build-up occurring.
We recommend
a warm or
hot wash at
regular
intervals e.g. approx. every 5th wash.
?
Fabric softener of thinner
consistency is
less
likely to
leave residue
on
the
dispenser and contribute to a build-up
CLEANING THE INSIDE OF YOUR WASHER
?
?
?
Fill your machine with hot water. Add about two cups of
a
powder detergent that contains phosphate.
Let it rotate for several minutes.
Stop the machine,
drain the machine and
run
We do not recommend that you wash clothes
the machine
through a regular cycle.
during this procedure.
25
Troubleshooting
Look for your problem below, then check the things we suggest. More often than not,
this will give you the answer to your problem. And you'll be able to carry on without
having to telephone your service center.
Troubleshting
WASH PROBLEM
Problem
Lint or residue
clothes
Possible Causes
Incorrect
sorting
Washing
too
What To Do
?
Separate lint producers from lint collectors.
on
long
?
Wash small loads for
a
shorter time than
larger
loads.
Detergent
on
clothes
Detergent not
dissolving
?
Try using less detergent
?
Use
?
Try liquid detergent.
Try pre-dissolving the detergent
?
Black spots
clothes
on
Incorrect use of
fabric softener
Dye transfer
Snags, holes,
tears, rips or
excessive
wear
Pins, snaps, hooks,
sharp buttons, belt
buckles, zippers,
and sharp objects
left in pockets
Undiluted chlorine
bleach
?
?
?
warmer
When
filling dispenser,
laundry
dirty
out
splash or overfill.
directly on clothes.
do not
Never pour fabric softener
Pre-treat stain and rewash.
lightly colored items from dark colors.
dry
separately
Sort whites
?
Wash and
?
Fasten snaps, hooks, buttons, and zippers.
Remove any loose brassiere wires.
?
or
non-colorfast clothes
objects in pockets and sharp buttons.
(which snag easily) inside out.
?
Remove
?
Turn knits
?
Check bleach
package instructions for proper
amount.
Never add undiluted bleach to wash
clothes to
comes
temperature.
?
?
The
water
a
come
or
allow
in contact with undiluted bleach.
Water temperature
is too cold.
Use
Stain is not pretreated
detergent dissolved in water onto stains
help shift dirt.
Wash stains as soon as possible. The longer they are
left the harder they are to remove.
Washer is
overloaded
Did you load too much into the machine?
Incorrect
White clothes
sorting
warmer
Brush
a
water
temperature
little
like collars and cuffs to
are
better washed
Separate light and heavily
separately.
soiled items.
26
T roubleshooting
Before
Troubleshting
calling for
Error
Symptom
Water
Supply
service check the
Failure
problem against
Message
the list belows.
Check up
.
.
.
.
.
Is the water tap shut off?
Is the water supply cut off ?
Is the tap
or
water
supply hose frozen
?
Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
Is Hot/Cold selected to Hot when the hose connected
is Cold?
.
Drainage
Failure
Is the Cold hose connected to Hot?
.
Is the drain hose
.
Is the drain hose bent
.
Is the internal part of the hose
positioned correctly?
or placed too high?
or
drain pump
(only pump model) clogged with impurities?
.
Spin
Failure
Door(Lid) Open
Internal sensing
failure
Power failure
Overflow failure
Check if electric power has gone off.
.
Is the
laundry evenly balanced?
.
Is the
washing machine placed on
.
Is the lid closed?
.
Ask for
help
at the
a
flat surface?
LG Electronic branch
of the Service Center
27
Specification
H
D
W
Model
WF-S(C/F)5101(~5)PC(H/P),S(C/F)5101(~5)PD(E/F),S(C/F)5111(~5)PC(H/P),S(C/F)5111(~5)PD(E/F)
WF-S(C/F)5201(~7)PC(H/P),S(C/F)5201(~7)PD(E/F),S(C/F)5211(~7)PC(H/P),S(C/F)5211(~7)PD(E/F)
WF-S(C/F)6101(~5)TC(H/P),S(C/F)6101(~5)TD(E/F),S(C/F)6111(~5)TC(H/P),S(C/F)6111(~5)TD(E/F)
WF-S(C/F)6201(~7)TC(H/P),S(C/F)6201(~7)TD(E/F),S(C/F)6211(~7)TC(H/P),S(C/F)6211(~7)TD(E/F)
WF-S(C/F)5301(~7)TC(H/P),S(C/F)5311(~7)TD(E/F),S(C/F)5401(~5)TC(H/P),S(C/F)5411(~5)TD(E/F)
WF-S(C/F)5201(~7),S(C/F)6201(~7),S(C/F)5301(~7): 530(W)x540(D)x850(H)
Size
WF-S(C/F)5211(~7),S(C/F)6211(~7),S(C/F)5311(~7): 530(W)x540(D)x900(H)
WF-S(C/F)5101(~5),S(C/F)6101(~5),S(C/F)5401(~5): 540(W)x540(D)x850(H)
WF-S(C/F)5111(~5),S(C/F)6111(~5),S(C/F)5411(~5): 540(W)x540(D)x890(H)
Water tab pressure
In
30 -800 kPa (0.3 -8
kgf /cm2)
continuing effort to improve the quality of our appliances,
changes to the appliance without revising this manual.
our
it may be necessary to make
P/No.: 3828EA3006D
Download PDF

advertising