LG | WF-T5402TC | LG WF-T5402TC Owner’s Manual

Washing
Machine
OWNER'S MANUAL
MODELS
:
WF-T5301(~5)TC(H/P)
WF-T5311(~5)TC(H/P)
WF-T5401(~2)TC(H/P)
WF-T5411(~2)TC(H/P)
WF-T5301(~5)TD(E/F)
WF-T5311(~5)TD(E/F)
WF-T5401(~2)TD(E/F)
WF-T5411(~2)TD(E/F)
Please read this manual
carefully
before
operating your
set.
Retain it for future reference.
Record model
name
and serial number of the set.
Quote this information to your dealer when you require service.
P
roduct Features
The Turbo Drum
washing machine does not operate with the lid open.
opened during wash, rinse and spin cycles, the machine will stop
automatically.
If the lid is
Fuzzy Logic Control
A built-in load
automatically detects and measures the laundry load a
microprocessor optimizes washing conditions such as ideal water consumption
and washing time.
sensor
into the Electronic Control
Advanced
the best
technology is built
washing result.
SENSING
START
Laundry
Sensor
Water Level Sensor
System
which
SETTING
Optimum
Washing
WASHING
Condition
Turbo Drum
While the "Punch
ensures
AUTO
POWER
OFF
washing
+
3"
pulsator
rotates in one
direction, the Turbo Drum rotates in the opposite
direction. This creates an
flow of water in both
even
the upper and lower parts of the drum,
enhanced washing and rinsing action.
Punch
The
+
resulting
in
an
3 washing action
powerful vertical water thrust
rotating pulsator movement
improves washing performance and reduces tangles.
punch
action's
combined with the
3
Spinning mini-pulsators create powerful jets of
laundry up and down in the
drum to ensure your laundry is evenly and
thoroughly washed.
water which move the
Lint Filter
Lint and loose threads from
during
for
a
the
washing cycle
laundry generated
caught by the lint
are
filter
cleaner wash.
Auto Restart
In the event of
its interrupted
Applied
a
power failure, the washing machine will
is resumed.
automatically
cycle when power
models
:
WF-T5301(~5)TD(E/F),WF-T5311(~5)TD(E/F)
WF-T5401(~2)TD(E/F),WF-T5411(~2)TD(E/F)
resume
C
ontents
Read this manual
Inside you will find many helpful hints on how to use and maintain your washer
Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
properly.
in the
Troubleshooting
section. If you review
our
chart of
Troubleshooting Tips first,
you
may not need to call for service at all.
Introduction
Before
Starting
Safety
to Wash
information
4
Identification of Parts
5
Function Information
6
Preparation Before Washing
7
Use of Water,
8
Detergent,
Bleach
and Softener
Function of each Button
Washing Programs
Fuzzy
Wash
Economy
Additional Function
Options
Installation
Care and Maintenance
10
(Normal Wash)
Wash
12
12
Jean Wash
12
Wool Wash
12
Soak Wash
12
Delay Start (Reservation)
Wash
14
Option Washing
15
Other useful Functions
16
Placing
and
Connecting
Water
Connecting
Drain Hose
Grounding
17
Leveling
Supply
Method
Hose
18
21
22
Cleaning
23
Troubleshooting
Troubleshooting
25
Specification
Specification
27
4
P
recaution
WARNING!
For your
safety, the information in this manual must be followed to minimize the risk of fire
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
Introducin
or
For your better understanding, these precautions are separated into two categories. We urge you to pay
special attention to them in the interests of your own safety, and protection of your machine against damage:
Caution
Violation of these
Attention
guidelines could result in
Installation
?
?
?
?
by young
supervision.
Do not install the washing machine in a damp place.
Keep the washing machine away from fire or heat
source.
?
or
use
infirm persons without
Young children should be supervised to ensure that
they do not play with the appliance.
The base opening must not be obstructed by
carpeting when the washing machine is installed on
carpeted floor.
sure
ground
Supply
cord
appliance
Make
to
ground the earth wire or connect it to
detector after you put the power cord into
?
?
?
injury.
When the power cord is loose, do not
Do not damage the power cords.
Do not
plug many cords into
one
use
?
a
a
?
?
an
it.
outlet at the
Do not put your hands
machine.
Do not place any rugs
the power cord.
or
or
feet under this
heavy material
over
outlet.
?
fatal
Attention
is not intended for
?
children
?
Power
The
or
Following these guidelines will protect your machine against damage.
Caution
?
serious
Since the machine is
heavy,
a
minimum
of two persons should move it.
Do not install the washer where it is
exposed to sunlight, wind, rain, etc.
The appliance must be positioned so
the plug is accessible
Make
sure
that
the power cord is free of dust
properly so that the cord
it in
and
plug
will
not move.
?
Do not touch the power cord with wet
hands.
?
Do not press the buttons with
same
time.
?
?
?
Operation
?
?
?
If the power cord or fuse is damaged, it must be
replaced by the manufacturer or its service agents or
similarly qualified people in order to avoid a hazard.
If the appliance is supplied from a cord extension
set or electrical portable outlet device the cord
extension set or electrical portable outlet device
should be positioned so it is not subject to splashing
or ingress of moisture.
When you take out the
fall into the washer.
laundry, be careful not to
?
Do not put hands into the rotating tub.
Do not sprinkle water over the buttons.
Make
sure
the lid is closed
?
during operation of the
spin cycle.
?
Maintenance
?
Do not put heavy objects on the machine.
Unplug the cord when the machine is not in
Do not pour
over
50
F)
water into
the tub.
?
use.
sharp objects.
Check the hose connection and open the tap
before activating the machine.
Do not wash any
waterproof materials.
?Do not pour corrosive materials or bleach
the washing machine. It will cause
over
the power cord or the machine.
Never disassemble or remodel the washer
damage to
?
and power cord by yourself. Only a
qualified technician should work on the
machine.
5
I
dentification of Parts
Body
Power cord
Water
EA
supply hose(1
Powder
Bleach
detergent
or
2EA)
box
dispenser
Inner tub
Control
panel
Lint filter
Drain hose
for pump model
Pulsator
Adjustable leg
Drain hose for
non
pump model
Accessories
Water
supply
hoses
Drain hose
or
or
1 Each for cold and
hot water
Note
Part
can
be different
according to the model.
Anti-rat
cover
(option)
Introducin
6
Function
Information
Our machine provides various washing methods which suits various conditions and
types of laundry.
BeforStaingWsh
Different
types of laundry washing
Fuzzy
(Normal) Wash
Use this
The
Program for normal clothes except for woolen clothes and lingerie.
automatically detects the quantity of laundry and selects the appropriate
washing time, rinsing time and spinning time. (refer to p12 )
sensor
power,
Economy
water
level, wash
Wash
Economy wash can be selected to wash lightly
soiled clothes of less than 2.0
kg in a short time. (refer
to
p12)
Jean Wash
Thick and
(refer
to
heavy clothes or those which
are
excessively dirty like jeans or working uniforms can be washed.
p12)
Wool Wash
Delicate clothes
(lingerie,
wool
etc.) which
may be
easily damaged can be washed. (refer
to
p12)
Soak Wash
Soak Wash
and
can
be selected to wash
grime. (refer
to
heavily soiled laundry by soaking in water for some time to remove dirt
p12)
Other washing methods
Delay Start (Reservation)
Wash
Delay Start (Reservation) Wash is used to delay the finishing time of the operation.
Delayed Start washing can be set according to preference. (refer to p14)
Option
Wash
Spin, Rinse/Spin, Rinse, Wash/Rinse,
and Wash
only options can selected. (refer
to
p15)
7
Before
Preparation
Washing
BeforStaingWsh
Sorting
results, different fabrics need to be washed in different ways.
Normal,
(Heavy,
Light)
Separate clothes according to amount of soil
COLOR (Whites, Lights, Darks)
Separate white fabrics from colored fabrics.
To get the best
SOIL
LINT
(Lint producers, Collectors)
Caring
?
before
Check all
such
as
Separate lint producers
and lint collectors.
loading
pockets to make sure that they are empty. Things
and keys can damage
nails, hairclips, matches, pens, coins
both your washer and your clothes.
?
Close
zippers, hook and strings to make sure that these items
don't snag
?
?
on
other clothes.
Mend any torn garments or loose buttons. Tears
become larger during washing.
Remove any loose brassiere wires
as
or
holes may
they can damage your
washing machine and clothes.
?
Pre-treat dirt and stains.
?
Make
?
Check the
sure
the clothes
are
WIRE
washable in water.
washing instructions.
Pretreatment
detergent dissolved in water onto stains like collars
help shift dirt.
Treat stains AS SOON AS POSSIBLE. The longer they are left the
harder they are to remove.
Brush
a
little
and cuffs to
Light
and
Large-size clothing
Clothes like downs and woollens
Long laundry
net and
are
light weight, large and float
wash them in
a small amount of water.
easily.So
nylon
If the laundry floats during the wash cycle, it may become damaged.
Use dissolved detergent to prevent the detergent from clumping.
use a
items
nylon nets for long, delicate items.
laundry with long strings or long length, a net will prevent
tangling during washing.
Fasten zippers or hooks on items before washing.
Nylon net is not supplied by LG.
Use
For
8
of Water,
Use
BeforStaingWsh
Detergent,
Bleach and Softener
Using water
Amount of water
This machine detects the
?
quantity of laundry automatically,
then sets the water level and proper amount of detergent.
When you select a wash program, the water level and
amount of detergent (to be used) will be shown on the
?
control
The
?
panel.
following table shows the amount of water.
Laundry Load
over3.1kg
Water Level /
Amount of Water
?
Ex 46l
under3.0
L 40l
kg
under2.0
under1.0
kg
kg
S 24l
M 33l
When the water level is
automatically detected, it may differ depending on the quantity of laundry even
though the same water level is indicated on the control panel.
Water temperature
?
The machine sets the
?
You
can
appropriate temperature automatically according to the wash program
change the water temperature by pressing WATER TEMP button.
(refer to p10)
Using Detergent and
Amount of
?
Fabric Softener
detergent
When you select a wash program, the water level and the amount of detergent will be
shown on the control panel. The amount of a cup in the diagram is about 40g for
concentrated
?
.
detergent.
For the correct amount of detergent, refer to
Available
detergent manufacturer's instruction
.
Detergent Type
Synthetic detergents that yield a low level of foam are recommended.
liquid detergent is used, mix it with water (1:1) and pour it into the bleach dispenser.
When
Attention
If excessive
pollution,
detergent is used, the rinse will not be as clean and efficient. Also, it could cause environmental
it accordingly.
so use
9
Available Fabric Softener
Do not
For
Type
concentrated fabric softener. This may cause some problems in automatic
details refer to the softener products instructions for use.
use
more
dispensing.
Depositing Detergent
Open the detergent dispenser and deposit the
appropriate amount of detergent
Powder
Detergent dispenser.
.
Where you
deposit the
detergent
Depositing
?
?
?
?
?
Fabric softener
Don't use softener with
rinse water
detergent.
When using dispenser, dilute
fresh water(30ml)
softener(30ml) with
When filling dispenser, do not
It may stain clothes.
Never pour fabric softener
It may stain them
Use softener in last
splash or overfill.
directly on clothes.
If spotting occurs, wet and rub hand
dishwashing liquid (or mild bar soap) and rewash.
Note
Fabric Softener will be inserted
Using
Bleach Check fabric
care
Available Bleach
Use
automatically during the final rinse.
labels for
special instructions.
Type
oxygenated bleach.
Powdered bleach should mixed with water and then be
For
more
details refer to the
Depositing
deposited into
products instruction for use.
the tub.
Bleach
Separate the laundry to be bleached and deposit
liquid bleach into the Bleach dispenser.
The dispenser dilutes liquid chlorine bleach before
Bleach
dispenser
it reaches into your wash load.
Attention
Do not insert bleach
or
fabric softener
directly onto laundry. This may affect colors or damage clothing
or acids such as vinegar and/or rust remover. Mixing can
Do not mix chlorine bleach with ammonia
produce a toxic gas which may cause death.
BeforStaingWsh
10
F
BeforStaingWsh
unction of each Button
Water
?
temperature button (option)
(indication of detergent amount)
Use to select water temperature.
Pressing the button allows you to select
Cold
Warm
Cold
respectively.
(Hot&Cold)
Default
Water level button
?
Hot
adjust the water level as required. The appropriate
detergent is shown next to the water level in
the WATER-DETERGENT diagram
Water level is automatically selected for fuzzy (normal)
and jean programs.
The following settings are indicated as the button is
EX-LARGE
SMALL
pushed LARGE
Use to
amount of
setting is Cold.
?
MEDIUM
LARGE
Process button
?
Use to select
desired.
Note
The control
panel may differ according to
different models
SOAK, WASH, RINSE
and SPIN functions
as
11
Program
?
?
?
Use for
Start/ Pause button
button
?
selecting wash program.
This button allows you to select 4
different programs for different kinds of
?
laundry and dirtiness.
program selections light up in sequence as
follows: FUZZY (NORMAL)
?
ECONOMY
JEAN
or
buttons to prevent
setting from
being changed by a child.
To lock, push the PROCESS, and
PROGRAM buttons simultaneously
and to unlock push them one more
time during the washing process.
(refer to p 16)
Repeats
washing process.
by pushing the
The power goes off automatically 10
minutes after stopping.
appliance is fitted with a safety
automatically stops the
of
the
operation
washing machine when
it is exposed to heavy disturbance on the
function that
WOOL
unlock the control
pause the
This
(NORMAL) etc, Select the
desired program by pressing the button.
Use to lock
or
start and pause
button.
FUZZY
Child lock function
Use to start
mains.
Delay Start (Reservation)
?
button
delayed finishing time.
changes 6 9 15(6+9)
when the button is pushed.
Use to set
a
The time
(refer
to
p14)
6hr
BeforStaingWsh
12
Washing Programs
WashingProm
Washing
Programs
AUTO POWER OFF
Add
the
Add
the detergent
laundry
Fuzzy Washing
(Normal Wash)
1
2
4
Add the appropriate
quantity of detergent as
indicated by the water
level next to WATERDETERGENT.
Or follow the detergent
manufacturer's
instructions
Used for normal loads, this mode
automatically selects the most
appropriate conditions and
completes the sequence in one
operation. The built-in sensor
detects the size of the load and the
ideal wash power and wash, rinse
and spin times are set accordingly
1
3
Economy Wash
Use this mode when washing lightly
solided clothes for
a short
2
5
Select the
ECONOMY
time. The
weight should be under 2.0kg.
program on
the Control
panel.
Jean Wash
1
5
2
3
Use jeans program when
washing
heavy, thick, and extremely dirty
laundry such as jeans and work
Select the
JEAN program
on the Control
outfits.
panel.
Wool Wash
Use this program for washing delicate
fabrics such
1
3
lingerie and woolens.
(wash
clothes)
Before washing your woolens check
the care label for the washing
program on
the Control
instructions.
panel.
as
Use neutral detergent
appropriate for the
laundry.
When washing
Select the
only "water washable"
(wash
5
2
WOOL
woolens use a mild
detergent recommended for washing wool.
only water washable clothes)
Soak Wash
1
Use this mode for washing
excessively dirty laundry by soaking
in water for some time to
remove
proteins and fats. 'SOAK' mode can
be used with all washing programs
simultaneously except for "WOOL"
program.
4
2
3
The SOAK
will not work
in WOOL
Program.
Keep pressing the PROCESS button until the SOAK light is on and then WASH,
RINSE, SPIN lights are on simultaneously.
If necessary, select the desired washing process from
(SOAK+WASH+RINSE+SPIN), (SOAK+WASH+RINSE),
(SOAK+WASH) manually.
6
13
Close the lid
3
Caution & Note
Finish
6
5
If water is already in the tub, or putting wet
laundry into the tub before starting will
The pulsator rotates for 8
Water will be supplied
When the wash
increase the water level.
seconds to detect the
for 2 minutes after the
With
laundry load.
program ends, the
start of the wash to
buzzer will
be set low.
ring for 10
Then the water level and
supplement the water
seconds before the
the amount of detergent to
the laundry has
be used will be shown and
Power goes off
absorbed.
automatically.
water will be supplied.
4
4
lightweight bulky loads, water level
can
Changes to water temperature (hot/cold) and
are possible during operation.
(refer to p 10)
wash level
6
7
6
7
When
setting the water level manually, do not
prevent damage to
laundry.
Washing with hot water may damage the
laundry (Water is set to cold automatically).
Ensure that the load is under 2kg
In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing may
set to MEDIUM to
4
6
7
t
still contain
some
water. This is normal.
Soak Wash cannot be selected for the Wool
d-
Wash program.
5
The water level and the
amount of detergent to be
used will be shown and
water will be supplied.
7
8
WashingProm
14
D
AditonalFucOps
elay Start (Reservation) Wash
Delay Start (Reservation) Wash is used to delay the finishing time of the
The hours to be delayed can be set by the user accordingly.
The time on the display is the finishing time not the start time.
operation.
,
1
Press the POWER button to turn power
on.
AUTO POWER OFF
2
Press the PROGRAM button to select the
washing program.
Select the program for laundry on the Control
This method will not work in Wool Program.
3
Press the DELAY START
delayed washing
is to
(Reservation) button
be completed.
The time
(69
4
Add the
detergent.
The
panel.
to set the time when the
changes as following order
6Hours).
appropriate quantity of detergent marked next to
water level of
the
WATER-DETERGENT.
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid
5
Add the
laundry
and press the START/PAUSE button.
When you press the START/PAUSE button the
blink.
6
an
supplied for 2 minutes after the start of the
supplement the water the laundry has absorbed.
Close the lid.
Water will be
Finish
The
wash to
light will
washing will be finished according to
the
delayed time.
Note
?
?
?
If the lid is open, the machine will not
work, and
an
alarm
signal will
alarm to remind you to close the lid.
washing program, spinning time, water level or hot/cold manually, press the DELAY START
(Reservation) button and select the desired option. Then press the START/PAUSE button.
To select
laundry cannot be taken out immediately after the wash program ends, it is better to
spinning program (The laundry will be wrinkled if left for a long time after spinning.)
When the
.
omit the
15
Option Washing
When you
1
only
need the Wash, Wash/Rinse
Press the AUTO OFF
(Power)
or
Rinse
these
cycles,
button to turn power
can
be set
manually
on.
AUTO POWER OFF
2
Wash
,
Wash+Rinse
,
Rinse
Rinse+Spin
,
,
Press the PROCESS button until above
light is on. ( refer to p11)
Spin only options
Option Washing
When you want to only drain, wait until the water in the
washing tub drains completely and then, turn off the
power.
3
Press the WATER LEVEL button, to control the water level according to the
laundry. If you do not choose anything, it is set the LARGE water
level automatically.
(refer to p10)
amount of
4
Add the
5
Press the START/PAUSE button.
6
Add the
laundry
into the
detergent
washing
tub.
and close the lid.
Note
?
When
a
Wash, Wash/Rinse or Rinse only option is selected,
after the wash is
completed the water will
drained off, If you wish to drain the water, press the SPIN button and wait until the water in the tub
has drained completely. Then press the START/PAUSE button
not be
.
?
?
If you do not
specify
If only Rinse is
the water level, then Medium will be
selected, the process will
start from Water
automatically selected.
Supply.
AditonalFucOps
16
O
AditonalFucOps
ther Useful Functions
Child Lock Function
If you want to lock all the
use
the child lock
keys to prevent all the setting from being changed by
child,
a
you
can
option.
How to Lock
1
Press the POWER button.
Turn Power
?
on.
AUTO POWER OFF
2
Press the START/PAUSE button to start
?
3
washing.
After all
washing conditions
are
set
according to
Press both the PROCESS button and the PROGRAM button
?
the manual.
simultaneously.
During the wash program, all the buttons are locked
washing is completed or it is child- lock
function is deactivated manually.
until
How to Unlock
If you want to unlock
during wash, press both the PROCESS
and the PROGRAM button
simultaneously
again.
Note
In child-Lock
mode, all process light will blink.
Auto Restart
Although the machine will not work during a power failure or if power is interrupted,
it will start again automatically from the point in the cycle when it stopped
Applied
Mute
models
:
when power is resumed,
WF-T5301(~5)TD(E/F),T5311(~5)TD(E/F)
WF-T5401(~2)TD(E/F),T5411(~2)TD(E/F)
Option
If you want to
use
the
washing machine
without alarm
signal sounds, press both the
WATER LEVEL and
PROCESS buttons simultaneously.
To make buzzer
time.
work, press both the WATER LEVEL and PROCESS buttons simultaneously one more
17
and
Placing
1
Leveling
Place the machine
on a
flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2cm right
side and left sides of the machine for ease of
more
installation.
At the rear,
than 10cm
more
a
minimum clearance of 10cm is
than
suggested.
2cm
more
than
2cm
2
Check that the machine is level
Open
the lid and look from above to
same as
see
Top
view of the machine
if it is
shown.
3 Leveling
the machine
Lift the front of the
washing machine and twist
Adjustable Leg
washing machine is
placed evenly.
until the
the
Adjustable legs
Installing the Anti-Rat Cover (option)
The anti-rat cover should be affixed
firmly from the back of the washer
UP
Caution
If the power is supplied from a cord extension set
outlet device should be positioned so that it is hot
or
generator, the cord extension
exposed
to
splashing
or
ingress
set
or
electrical
of moisture.
portable
Introducin
18C
Instal ion
onnecting
Supply Hose
Before connecting the Water Supply Hose to the water tap, check the hose type and
then choose the correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country, Make
sure to connect the blue inlet hose to the cold water tap, and the orange inlet hose to
the hot water tap
Connecting
Water
Normal
1
Water
Supply
Hose to water
Type
Untighten
the
(Normal tap without thread &
Fixing
screw
type inlet hose.)
Rubber
screw
Untighten the screw of the connector so
tap can be placed in the middle.
2
tap
packing
that the
screw
Connector
the connector to the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4
3
screws.
Attach the water
to the connector
Push the water
supply
hose connects
supply hose vertically upwards
that the rubber seal within the hose
can
securely
Connector
so
adhere
completely to the tap.
Water
Supply
4
Fixing
the connector of connector and water
supply
Attach the water
then
5
supply hose to the connector and
tighten it by screwing it to the right.
Check the connection to the water
After
supply
connecting the hose, open the tap to check
for any water leakage.
If the connection leaks, close the tap and start
again from step
1
hose.
hose
Hose
19
Normal
1
Type
Separate
(Normal tap without thread & one touch type inlet hose.)
Middle connector from Water
Supply
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose while pressing them.
Hose
Middle
Fixed Sticker
connector
Pressing
Handle
Pressing
Rod
Water
2
Supply
Hose
Loosen the fixed nuts to connect the connector to the tap
Untighten the screw of the connector so that the
tap can be placed in the middle.
Rubber
packing
screw
Fixed sticker
Note
In
case
the tap is too
large.
Guide
plate
Rubber
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate.
3
Then follow
packing
step1.
Fixing Connectors to
the
Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
4
Fixing Upper Connector
and Middle Connector
Remove the fixed sticker in between the
Connector
Upper
and Middle Connectors. Tighten the connectors
by holding one connector and twist middle
connector to the right.
5
Connecting
Middle
Connector
Fixed sticker
Middle Connector and Water
Supply
pressing rod of the Water Supply
separated from middle connector
and
then join it to the middle
Step1)
Connector
Middle
Connector
Hose
Press down the
Hose which
(refer to
was
Pressing
rod
connector.
Water
6
Check for water
After
leakage
hose, open the tap to check
connecting
for any water leakage.
If the connection leaks, close the tap and start
again from step
the
1.
Supply
Hose
Pressing
handle
Instal ion
20
C
Instal ion
onnecting
Screw
1
Water
Supply Hose
Type
Attach the water
hose to the tap.
supply
Push the water supply hose up so that the rubber
packing within the hose can adhere completely to
the tap.
Water
tap
Rubber
Water
2
Connect the water
supply
Packing
Supply
hose to the tap.
Connect the water
tighten it by
3
supply hose to the tap and then
screwing it to the right.
Check water
leakage.
After
connecting the hose, open the tap to
for any water leakage.
Connecting
Water
Supply
Connect the water
the
check
Hose to the machine
supply hose to
inlet valve of
and then lock it by
washing machine,
connecting part.
turning
the hose
Check
to
see
if there is
the connector.
a
rubber seal inside
Hose connector
Rubber seal
Hose
21
Connecting
Drain Hose
Before connecting Drain Hose, check your Drain Hose model and choose
the correct instructions.
Pump
Instal ion
Model
1
Fit the machine end of the drain hose to the outlet
2
Put the other end of the drain hose over the
of the drain pump and
tighten the clamp.
standpipe or
wash tub.
Hose
Guide
Within 50mm
0.9~1.2m
Drain Hose
Note
To prevent siphoning, the drain hose should not extend more than 50mm from the end of the hose
The discharge height should be approximately 0.9
1.2 m from the floor.
~
Non-Pump
1
Before
Model
connecting
Ensure that the hose
clip
is set
as
indicated here.
Clip
2
Connect the Elbow Hose
Push the elbow hose toward the
body of the
washing machine.
3
Place the Drain Hose
change the direction of the hose, pull out the
change the direction.
Repeat Step2.
To
elbow hose and
guide.
22
G
CarendMitc
rounding
Method
Earth wire should be connected.
If the earth wire is not connected, there is
caused by the current leakage.
Grounding
possible
a
danger of
Method with Ground insert space Terminal
If the AC current outlet has
ground terminal, then
separate grounding
required. Note that AC
outlet
power
configurations may differ from country
a
Ground Terminal
is not
to
country
Outlet with
Other
electric shock
Grounding
terminal.
Method
Burying Copper
Plate
Connect the Ground Wire
Plate and
ground
bury
it
more
to
a
Ground
Copper
ground.
than 75cm in the
Ground Wire
75cm
Using Ground
Ground
Wire
Copper
ground Wire to the socket provided
exclusively
Grounding.
Plate
Connect the
for
Using Short Circuit
Breaker
If grounding methods described above
possible,
employed
a
Ground
Wire
are
not
Short-circuit
separate circuit breaker should be
and installed by a qualified electrician
breaker
Caution
?
?
To prevent a possible explosion, do not connect ground to a gas pipe
Do not connect ground to telephone wires or lightning rods. This may be
storms
?
Connecting ground to plastic has no
?
Ground wires should be connected when
effect
an
extension cord is used.
dangerous during electrical
23
Cleaning
supply into the tub is not clean or the filter is clogged with
particles(Such
sand), clean the filter in the inlet valve occasionally.(The figure of
power cord and water tap may vary according to the country)
When water
as
To Clean the Filter in the Inlet Valve
Close the tap before
1
turning off the
water from the machine
removing the water
supply hose pull out the filter.
Then
use a
pulling out the cord.
completely.
After
3
Turn off the power before
2
power.
Select both hot/cold and then press the
[START/PAUSE] button to remove
4
Replace the filter after cleaning it.
brush to clean
the filter.
Caution
Before
?
cleaning the filter,
the
impurities in the water supply hose should be removed.
To Clean the Lint Filter
1
Pull out the lint filter from
2
Turn the net inside out to
3
the tub in the direction
clean the filter and rinse it
Replace- the filter to the
original location. Push the lip
shown below.
with water.
of the filter until
a
pop sound
is heard.
Note
?
If the lint filter is torn
To Clean the
1
damaged, purchase a new
one
from LG service center.
Pump casing (for pump model)
Unfasten 4
back
or
screws
of the
cover.
2
Turn the cap as shown in
diagram and unfasten it.
Remove
as
foreign objects
pin, button, coin,
3
fasten it.
such
etc
(Bottom view)
(Bottom view)
Caution
?
Check if water leaks after
reassembling. (The
Rubber
Reassemble the cap to
the arrow direction and
ring
is in the
cap)
CarendMitc
24
C leaning
CarendMitc
WHEN THERE IS A FEAR OF FREEZING
1
Close the water taps and
2
Remove the water which remains in the water
3
Lower the drain hose and drain the water in the bowl and the drain hose
remove
the Water
Supply Hose.
supply.
by spinning.
IF FROZEN
and immerse it in hot water at approx. 40 ˚C.
1
Remove the water
2
Pour approx. 2 liters of hot water at approx. 40
3
Connect the water
supply
and
supply hose,
supply hose to
drainage of water.
Wash Inner-tub
˚C, into
the bowl and let it stand for 10 minutes.
the water tap and confirm that the
washing machine performs
the
Leave the lid open after washing to allow moisture to evaporate. If you want to clean
use a clean soft cloth dampened with liquid detergent, then rinse. (Do
the inner-tub
not use harsh or
Inlet Hoses
Hoses
connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
sharp objects.
Exterior
Long
gritty cleaners.)
Vacations
Be
sure
water
supply
freezing.
be below
surface with
is shut off at faucets. Drain all water from hoses if weather will
SCRUD
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
into contact with detergent. This build-up is not brought about by a fault in the machine.
comes
If scrud is allowed to build-up in the machine it
smell in your washer.
can
result in stains
on
your clothes
or an
unpleasant
If you wish to
?
?
?
?
Using fabric
Clean
use
the
dispenser,
dispenser as
soon as
Clean your machine
Cold water
fabric softener
do not
the
we
recommend.
splash or overfill.
cycle has
finished.
regularly
washing increases
the chance of this
build-up occurring. We recommend
a warm or
hot wash at
regular
intervals e.g. approx. every 5th wash.
?
Fabric softener of thinner
consistency is
less
likely to
leave residue
on
the
dispenser and contribute to a build-up
CLEANING THE INSIDE OF YOUR WASHER
?
?
?
Fill your machine with hot water. Add about two cups of
a
powder detergent that contains phosphate.
Let it rotate for several minutes.
Stop the machine,
drain the machine and
run
We do not recommend that you wash clothes
the machine
during
this
through a regular cycle.
procedure.
25
Troubleshooting
Look for your problem below, then check the things we suggest. More often than not,
this will give you the answer to your problem. And you'll be able to carry on without
having to telephone your service center.
Troubleshting
WASH PROBLEM
Problem
Lint or residue
clothes
Possible Causes
Incorrect
sorting
Washing
too
What To Do
?
Separate lint producers from lint collectors.
on
long
?
Wash small loads for
a
shorter time than
larger
loads.
Detergent
on
clothes
Detergent
dissolving
not
?
Try using less detergent
?
Use
?
Try liquid detergent.
Try pre-dissolving the detergent
?
Black spots
clothes
on
Incorrect use of
fabric softener
Dye transfer
Snags, holes,
tears, rips or
excessive
wear
Pins, snaps, hooks,
sharp buttons, belt
buckles, zippers,
and sharp objects
left in pockets
Undiluted chlorine
bleach
?
?
?
warmer
When
filling dispenser,
laundry
dirty
out
splash or overfill.
directly on clothes.
do not
Never pour fabric softener
Pre-treat stain and rewash.
or
lightly colored items
from dark colors.
dry
non-colorfast clothes
separately
Sort whites
?
Wash and
?
Fasten snaps, hooks, buttons, and zippers.
Remove any loose brassiere wires.
?
objects in pockets and sharp buttons.
(which snag easily) inside out.
?
Remove
?
Turn knits
?
Check bleach
package instructions for proper
amount.
Never add undiluted bleach to wash
clothes to
comes
temperature.
?
?
The
water
a
come
or
allow
in contact with undiluted bleach.
Water temperature
is too cold.
Use
Stain is not pretreated
detergent dissolved in water onto stains
help shift dirt.
Wash stains as soon as possible. The longer they are
left the harder they are to remove.
Washer is
overloaded
Did you load too much into the machine?
Incorrect
White clothes
sorting
warmer
Brush
a
water
temperature
little
like collars and cuffs to
are better washed separately.
Separate light and heavily soiled items.
26
T roubleshooting
Before
Troubleshting
calling for
Error
Symptom
Water
Supply
service check the
Failure
problem against
Message
the list belows.
Check up
.
.
.
.
.
Is the water tap shut off?
Is the water supply cut off ?
Is the tap
or
water
supply hose frozen
?
Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
Is Hot/Cold selected to Hot when the hose connected
is Cold?
.
Drainage
Failure
Is the Cold hose connected to Hot?
.
Is the drain hose
.
Is the drain hose bent
.
Is the internal part of the hose
positioned correctly?
or placed too high?
(only pump model) clogged
.
Spin
Failure
Door(Lid) Open
Internal sensing
failure
Power failure
Overflow failure
or
with
drain pump
impurities?
Check if electric power has gone off.
.
Is the
laundry evenly balanced?
.
Is the
washing machine placed on a flat surface?
.
Is the lid closed?
.
Please call your nearest LG Electronics service center
for help.
27
Specification
Specifaton
H
D
W
Model
WF-T5301(~5)TP(H/C),WF-T5311(~5)TP(H/C),WF-T5401(~2)TP(H/C),WF-T5411(~2)TP(H/C)
WF-T5301(~5)TD(E/F),WF-T5311(~5)TD(E/F),WF-T5401(~2)TD(E/F),WF-T5411(~2)TD(EF)
Weight
30
Size
530(W)x540(D)x850(H) WF-T5301(~5)
kg
530(W)x540(D)x900(H) WF-T5311(~5)
540(W)x540(D)x850(H) WF-T5401(~2)
540(W)x540(D)x890(H) WF-T5411(~2)
Water tab pressure
The appearance and
30 -800 kPa (0.3 -8
specifications
kgf /cm2)
may be varied without notice to raise the units
quality.
P/No.: 3828EA3003L
Download PDF

advertising