LG | WFT11C65ED | LG WFT11C65ED Owner’s Manual

Washing
Machine
OWNER'S MANUAL
MODEL
:
WFT(R,N,S,C,F)10(1)C64(5)D(E)C(H,P,D,E,F,M)
WF-T1250TD
WF-T1391TP
WF-TS1688TC
Please read this manual
carefully
before
operating your
set.
Retain it for future reference.
Record model
name
and serial number of the set.
Quote this information to your dealer when you require service.
P
roduct Features
Washer doesn't operate while the lid is open. If the lid is open
the operation stops for safety.
rinse
or
spin cycles,
(option)
sensors
The
during the wash,
automatically detects the quantity of a Detergent put by a user and
temperature and the quality of water to make the best washing algorithm for
washing and rinsing, which can give the best washing effect.
sensor
FUZZY
logic
A built-in load
control
automatically detects the laundry load and a
microprocessor optimizes washing conditions such as ideal WATER
and washing time.
START
sensor
SENSING
SETTING
Laundry Sensor
Optimum
WASHING
Condition
Advanced
technology is built into the
ensures the best
washing result.
Turbo drum
tub
the
turns in
sides
current
3"
+
washing
3
models
:
System
which
(option)
the
washing
direction. This makes the both
of water which
performance by rubbing
Applied
Electronic Control
washing wings turn,
opposite
LEVEL
AUTO
POWER
OFF
Washing
Water Level Sensor
When "Punch
the
improve
clothes
wash-
strongly.
WFT
Step washing
3
step washing makes the best washing performance with low tangling.
Rubbing
NOTE
:
Be
sure
Rubbing and
Shaking
Shaking and
Disentangling
to remove the unit from the carton
machine will not be able to operate
base, otherwise the
properly.
Contents
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your washer
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your washer. You will find many answers to common problems
in the
section. If you review
you may not need to call for service at all.
Troubleshooting
Introduction
Before
Starting
Safety
to Wash
chart of
Troubleshooting Tips first,
Information
4
Identification of Parts
7
Function Information
8
Preparation
Use of
Before
Washing
Water, Detergent, Bleach and Softener
Special
Washing Programs
our
Guide for Stain Removal
9
10
13
Function of each Button
14
FUZZY Wash
16
QUICK
(Normal Wash)
WASH
16
JEAN Wash
16
WOOLWash
16
DELICATE
16
SOAK Wash
18
FAVORITE Wash
19
SILENT
20
Additional Function
TUB CLEAN
21
Program
AIR DRY
22
Option Washing
23
DELAY START (RESERVATION) Wash
24
Other Useful Functions
25
Installation
Placing
and
Leveling
Connecting Water Supply
Connecting
Care and Maintenance
Troubleshooting
Terms of
Warranty
Specification
26
Hose
Drain Hose
27
30
Grounding Method
Cleaning and Maintenance
Common washing problems
Troubleshooting
31
Terms of
36
Warranty
Specification
32
34
35
37
4
S
Introducin
afety
Read
Information
thoroughly through this booklet as it contains important safety information
protect the user from unexpected dangers and prevent potential damages to the product.
carefully
that will
and
This booklet is divided into 2
:
This is
be
:
parts
:
Warning
warning sign specifying
dangerous.
This is
a
a
sign specifying 'Strictly
and Caution.
user's
applications
Forbidden'
which
might
applications.
Warning
:
comply with the instructions under this
sign may result in major physical injuries or death.
Caution
:
Failure to
comply with
sign may
damages
result in minor
Failure to
WATER
to the
the instructions under this
physical injuries
or
product.
Warning
HEATER
SAFETY
?
Under certain conditions
hydrogen gas may be produced in a water heater that has not been
used for two weeks or more. Hydrogen gas can be explosive under these circumstances.
If the HOT water has not been used for two weeks or more, prevent the possibility of
damage or injury by turning on all Hot water faucets and allowing them to run for several
minutes. Do this before using any electrical appliance which is connected to the HOT
water system. This simple procedure will allow any built-up hydrogen gas to escape. Since
the gas is flammable, do not smoke or use an open flame or appliance during this process.
PROPER
Caution
INSTALLATION
?
The base
opening must not be obstructed by carpeting when the washing machine is
installed
on a
carpeted floor.
?
where it will not be
Install
or
If the
product is exposed to
store
deformation may
?
exposed to temperatures below freezing or exposed to the weather.
such
conditions, electric shock, fire, break down or
occur.
Properly ground washer to conform with all governing codes and ordinances. Follow details in
Installation Instructions.
?
If not
grounded properly, break down and leakage of electricity may occur, which may
cause
electric shock.
Must be
positioned so that the plug is
accessible.
If the
plug is placed between the wall and the machine, it may get damaged, possibly
causing fire or electric shock.
?
Make
sure
the
plug is completely pushed into the outlet.
Failure to do
so
may
cause
electric shock and fire due to
overheating.
5
Safety
Information
YOUR
Warning
LAUNDRY
AREA
?
Keep
the
underneath and around your
area
materials such
as
lint,
paper, rags,
Operating with such
explosion or fire.
?
appliances
chemical,
free of combustible
etc.
materials around the machine may
trigger
is necessary if this appliance is used by or near children.
Do not allow children to play on, with, or inside this or any other appliance.
Close
supervision
There is
potential danger
that children
Do not touch the power
It will
cause
plug with
a
might
drown in the tub.
wet hand.
electric shock
Do not put your hand, foot or anything under the
while the washing machine is in operation.
There is
WHEN USING
a
washing
machine
rotating mechanism under the machine, so you could be injured.
Caution
THE WASHER
?
?
?
Use this
appliance only for its intended purpose as described in this Owner's Manual.
The laundry process can reduce the flame retardancy of fabrics. To avoid such a result,
carefully follow the garment manufacturer's wash and care instructions.
To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the washer at the household distribution panel by removing the
fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.
NOTE
:
Pressing
Power button to turn off does NOT
disconnect the
?
Make
sure
that
appliance
from the power
supply.
drainage is working properly.
If water is not drained
properly, your floor may get flooded. Flooded floors
may induce electricity leakage, further resulting in electric shock or fire.
?
If, during spinning, opening the lid does
not
stop the tub within about 15 seconds,
immediately discontinue operating the machine.
Call for
repair. A machine
that
spins with its
door open may
cause
injuries.
Never reach into washer while it is
Wait until the
moving.
machine has completely stopped before opening the
Even slow rotation
can cause
Never attempt to operate this
disassembled, or has missing
lid.
injury.
appliance if it is damaged, malfunctioning, partially
or broken parts, including a damaged cord or plug.
Operating with a damaged plug may cause electric shock.
Do not
use
water hotter than
50°C.
Use of excessively hot water may
leakage of water.
cause
damage to fabrics or cause
Introducin
6
S
Introducin
afety
Information
WHEN USING
Warning
THE WASHER
wiring equipment for more than their rated capacity.
Exceeding the limit may lead to electric shock, fire break down, and/or
deformation of parts.
Do not use
plug
a
socket and
,
Do not mix chlorine bleach with ammonia
or
acids such
as
vinegar and/or rust remover.
Mixing different chemicals can produce toxic gases which may cause death.
dry articles that have been cleaned in, washed in, soaked in, or spotted
with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.
Do not use or place these substances around your washer or dryer during operation.
Do not wash
It may
WHEN NOT
or
ignite or explode.
Caution
IN USE
?
Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage
if a break or rupture should occur. Check the condition of the fill hoses; they may need
replacement
?
?
after
5years.
When the air temperature is high and the water temperature is
occur and thus wet the floor.
Wipe off dirt or dust on the contacts
of the power
Using unclean power plug may cause
?
low, condensation may
plug.
fire.
discarding a washer, or removing it from service, remove the washer lid to
prevent children from hiding inside.
Before
Children may be
trapped and suffocated if the lid is left intact.
Do not attempt to repair or replace any part of this appliance unless specifically
recommended in this Owner's Manual, or in published user-repair instructions
that you understand and have the skills to carry out.
Operating the
cause
for fire
machine with
or
improperly replaced parts
may be
a
electric shock.
Do not tamper with controls.
It may lead to electric
shock, fire break down, deformation.
,
yank the power cord in an attempt to disconnect the power plug.
Securely hold the power plug to unplug the machine.
Do not
Failure to observe these instructions may
due to short-circuit
or
fire
apply water directly to
any
cause
electric shock
.
When you
part of the
It will
cleaning the washing machine,
washing machine.
are
cause
do not
short circuit and electric shock.
7
Identification
of Parts
Body
POWDER AND
LIQUID
DETERGENT BOX
WATER SUPPLY
HOSE
Make
*
sure
the
water does not
SOFTENER
Softner will
INLET
leak.
automatically
flow into the tub.
POWER PLUG
If the
supply cord is
damaged, it must be
replaced by the
BLEACH
DISPENSER
manufacturer
service agents
or
its
or
FUNCTION
similarly qualified
SELECTOR
person in order to
avoid a hazard.
TUB
LINT FILTER
Clean
regularly to
stop linting on the
START/PAUSE
BUTTON
Use to start
clothes load.
or
stop the washing
DRAIN HOSE
for pump model
machine
temporarily.
Check if the drain
hose is
hung up
before operating the
washing machine.
DRAIN HOSE
ADJUSTABLE LEGS
Use to level the
for
washing
non
pump
model
machine for correct
balance &
spin
operation.
BASE
Accessories
Water
supply
hoses
Drain hose
or
or
1 Each for COLD and
HOT water
NOTE
Part
can
be different
according to the model.
Anti-rat
cover
(option)
Introducin
8
F
unction Information
Our machine
Different
provides various washing
types of laundry.
types of laundry washing
methods which suits various conditions and
FUZZY(Normal) Wash
Use this
Program for everyday washing
e.g.
sheets, towels, T-shirts. (refer to page 16)
JEAN Wash
Use this
Program for heavily soiled durable garments e.g. overalls, jeans.
Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms
can
be washed.
(refer to page 16)
DELICATE Wash
Use this program to wash DELICATE and washable laundries.
(refer to page 16)
WOOL Wash
Delicate clothes
(lingerie, wool, etc.)
which may be
The fibers of machine washable woolens have been
Most handknitted
garments
are
easily damaged can be
washed.
(refer to page 16)
modified to prevent felting when they are machine washed.
not made of machine washable wool and we recommend that you hand wash them
specifically
washing your woolens check the care label for the washing instructions.
When washing woolens use a mild Detergent recommended for washing wool.
Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.
To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.
(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)
Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages.
(Ensure that the whole article is suitable for machine washing and not just the backing material.)
You may wish to handwash these articles and place them in the machine to spin dry.
?
Before
?
?
?
FAVORITE Wash
This
setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 19)
SILENT Wash
Use this program to wash
Washing according
quietly at night. (refer to page 20)
to the condition of
laundry
QUICK WASH
QUICK WASH
can
be selected to wash
lightly
soiled clothes of less than 2.0
kg in a short time. (refer to page 16)
SOAK Wash
SOAK Wash
can
be selected to wash
heavily soiled laundry by soaking in water for some time to remove dirt and
grime. (refer to page 18)
Other
washing
method
TUB CLEAN
Use this program to clean the inside of washing machine
especially Inner tub & Outer tub
.
(refer to page 21)
AIR DRY
Use this program to reduce
remaining moisture
inside of washing machine and
on
the
laundry.
DELAY START Wash
DELAY START Wash is used to
delay the finishing time of the operation.
The number of hours to be delayed can be set by the user accordingly. (refer to page 24)
OPTION WASH
When the
needs
only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN,
SOAK/WASH/RINSE/SPIN.
(refer to page 23)
user
9
Before
Preparation
Washing
BeforStaingWsh
Care Labels
*
your clothes. This will tell you about the fabric content of your garment
and how it should be washed.
Look for
a care
label
on
Sort clothes into loads that
can
be washed with the
same
wash
cycle, Water Temperature and spin speed.
Sorting
To get the best results, different fabrics need to be washed in different ways.
?
?
?
(Heavy, Normal, Light)
Separate clothes according to the type and amount of soil.
COLOR (Whites, Lights, Darks)
Separate white fabrics from colored fabrics.
LINT (Lint producers, Collectors) Separate lint producers and lint collectors.
SOIL
Lint Producers
Terry cloth, Chenille, Towels, Nappies, Diapers
Synthetics, Corduroy, Permanent Press, Socks
Lint Collectors
Check before
?
?
?
?
?
?
?
Loading
Check all
pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
Pretreat any dirt and stains.
Make sure the clothes are washable in water.
WIRE
washing instructions.
Remove tissue in pockets.
Check the
Pretreatment
on
stains
or
heavy soil
?
Pretreat shirt collars and cuffs with
pre-wash product or liquid Detergent when placing them in the washer.
Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.
?
Use
a
a
pretreat soil and stain remover.
Treat stains AS SOON AS POSSIBLE. The
longer they are left the harder they are to remove.
(For more detail refer to page13)
Loading
Do not wash fabrics
WARNING
containing flammable materials (waxes, cleaning fluids, etc.).
Fire Hazard
Load Size
The WATER LEVEL should just
cover
the clothes.
Adjust the load size
accordingly. Loosely load clothes no higher than the top row of holes in the
washer tub. To add items after washer has started, press Start button and
submerge additional items. Close the lid and press Start button again to restart.
Light
and
Large-sized clothing
Clothes like downs and woollens
Never
place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer
completely remove oil.
Do not dry anything that has ever had any type
of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
can
light weight, large and float easily. Use a nylon net and
wash them in a small amount of water. If the laundry floats during the wash cycle, it may
become damaged. Use dissolved Detergent to prevent the Detergent from clumping.
are
Long laundry items
Use nylon nets for long, DELICATE items. For laundry with long strings or long length a net will prevent
tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.
Nylon net is not supplied by LG.
,
10
U
BeforStaingWsh
Using
of Water,
se
Detergent,
Bleach and Softener
Water
Amount
?
of
WATER
This machine detects the
WATER LEVEL
quantity
of
laundry automatically,
and proper amount of Detergent.
then sets the
?
When you select a wash program, the WATER LEVEL and amount of
Detergent (to be used) will be shown on the control panel.
?
The
?
When the WATER LEVEL is
?
following
table shows the amount of water.
automatically detected, it may differ depending
on the quantity of laundry even though the same WATER LEVEL is indicated
on the control panel.
The amount of a cup in the diagram is about 40g for concentrated Detergent.
NOTE
[ Minimum water amount ]
It depends on laundry load and washer model. Or manually you can pour a certain amount water into tub
directly to some height. That's because if water level reaches to the some height sensed by washer itself, washer
automatically operates. In other words, it is needed to pour water to the point when washer starts operating.
Water
?
?
?
The machine sets the
appropriate temperature automatically according to the wash program
You can change the Water Temperature by pressing the WATER TEMP. button. (refer to page 14)
.
The temperature of the water impacts the effectiveness of all
We recommend temperatures of:
-
-
-
?
Temperature
HOT 49~60°C...(120-140˚F)
White
WARM
Most items
29~40°C...(85-105˚F)
COLD* 18~24°C...(65-75˚F)
laundry additives
items, diapers, underclothing
Only very bright colors
with
and
and
therefore, the cleaning results.
heavily soiled,
colorfast items.
light soil.
washing in COLD water additional steps may be needed:
Adjust Detergent amount and pre-dissolve Detergent in WARM water
When
-
-
-
Pretreat spots and stains
Soak heavily soiled items
appropriate bleach
*
Temperature below 18°C...(65˚F) will not activate laundry additives and may cause lint, residue, poor cleaning, etc.
In addition, Detergent manufactures and care labels define COLD water as 26~29°C...(80-85˚F).
If the temperature of the water in the tub is too cold for your hands, the Detergent will not activate and clean effectively.
-
Use
NOTE
If iron is present in the water the clothes may become an all-over yellow or they may be stained with brown or orange
spots or streaks. Iron is not always visible. Installation of water softener or an iron filter may be necessary for severe cases.
Using Detergent
Detergent
Follow the Detergent package directions. Using too little Detergent is a common cause of laundry problems.
Use more Detergent if you have hard water, large loads, greasy or oily soils or lower Water Temperature.
Choosing the right Detergent
of domestic Detergent, (powder, liquid or concentrated). Soap flakes or
granulated soap powders should not be used in your washing machine. When washing woolens
remember to use Detergent suitable for washing woolens.
We recommend the
use
11
Using Detergent
How much
Detergent
When you select a wash program the WATER LEVEL and the amount of Detergent (to be used) will be
shown on the control panel. The amount of a cup in the diagram is about 40g for concentrated Detergent.
The correct amount of Detergent will vary depending on the amount of soil in your clothes
cloches may need more Detergent, while bath towels usually need less.).
(Jeans
and work
liquid and concentrated Detergents, follow the recommendations of the Detergent manufacturer.
Note: To check you are using the correct amount of Detergent, lift the lid of your machine about halfway through the wash. There should be a thin layer of foam over the surface of the water. Lots of
foam may look good, but it does not contribute to cleaning your clothes. No foam means not enough
Detergent has been used; soil and lint can settle back on the clothes or the washing machine.
For
If excess
Detergent is used, the rinse will
environmental
not be
as
clean and efficient.
Also, it could
cause
pollution, so use it accordingly.
Adding the Detergent
Open the Detergent dispenser and deposit
Powder/Liquid Detergent dispenser
the appropriate amount of Detergent
where you deposit the Detergent
Powder Detergent
When using Liquid Detergent,
Limit Line
make sure the detergent box and insert are in place.
Depositing
liquid don't fill
Some Detergents MUST be fully dissolved before
it above the
limit line.
adding to your machine to get the best wash results.
Liquid Detergent
Check the instructions on the Detergent packet.
If you use powdered Detergent it is essential that the required amount be fully dissolved in very HOT water
before being added to WARM or HOT water for the actual wash.
Pre-dissolving Detergent in WARM water when washing in COLD water can improve its performance.
Using Liquid
Bleach
?
Check
care
?
Dilute
liquid chlorine bleach.
label for
clothing
laundry to be bleached
special
instructions and separate the
?
Measure the recommended amount of liquid bleach
following instructions on the bottle.
?
Before starting the washer, pour measured amount of bleach directly
into bleach dispenser. Avoid splashing or overfilling. Powdered
bleach should be mixed with water before pouring.
carefully
NOTE
Never pour undiluted liquid bleach directly onto clothes
This may cause change of color or damage the laundry.
Do not pour
powdered bleach into bleach dispenser.
or
into the wash basket.
Bleach
dispenser
BeforStaingWsh
12
U
BeforStaingWsh
se
of Water,
Detergent,
Bleach and Softener
Fabric Softener
Using
?
?
Dilute fabric softener with water.
Undiluted fabric softener may result in spots that look like oil
stains.
Softener
dispenser (
)
Measure and add the recommended amount of fabric softener
into the compartment marked with this symbol(
).
Follow manufacturer's direction.
or
F
Fabric softener is automatically
with indication beep.
F
If you want EXTRA RINSE, you must add fabric
softener manually when indication beep rings in the final
rinse. This maximize the fabric softener function.
?
dispensed in the final rinse
Do not overfill. The dispenser hold
Never add more than 35mL.
max
35mL.
Overfilling can cause early dispensing of the fabric
which could result in stained clothes. A cup with
?
a
softener
pouring spout will help
you avoid
spilling.
The effect of adding fabric softener may vary according to its viscosity. The stickier fabric softener makes its
effect the lower. For a sticky fabric softener it is recommended that it be diluted with water, then be manually
put during the time when the washer beeps several times before the final rinse. This function informing
correct time to dispense manually is optionally applied to some models. Please keep it in mind that fabric
softener has to be diluted with water before dispensed and never poured directly on clothes.
Attention
Do not mix with
Detergent or bleach.
Never pour fabric softener directly on clothes. It may stain them.
Do not stop the washer during the first spin for timely dispensing.
Option washing is not designed to be used with fabric softener dispenser.
Scrud(Waxy
Build
up)
Scrud is the name given to the waxy build-up that can occur within any washer when the fabric softener
comes into contact with Detergent. This build-up is not brought about by a fault in the machine.
If scrud is allowed to build-up in the machine it
smell in your washer.
If you wish to
?
?
?
?
?
?
use
fabric softener
we
can
result in stains
on
your clothes
or an
unpleasant
recommend
Using fabric softener sparingly.
When filling the dispenser, do not splash or overfill.
Clean dispenser as soon as the cycle is finished.
Clean your machine regularly. (refer to page 19 or 30)
Cold water washing increases the chance of this build-up occurring. We recommend a regular WARM or
HOT wash e.g. every 5th wash should be at least a warm one.
Fabric softener of thinner consistency is less likely to leave residue
build-up.
on
the
dispenser and contribute to
a
13
Guide for Stain Removal
Special
WARNING
Do not
liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or
products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.
To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:
Read and
?
?
?
?
?
?
use or
mix
comply
with all instructions
on
stain removal
products.
Keep stain removal products in their original labeled containers and out of children's reach.
Thoroughly wash any utensil used.
Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents
or other flammable or explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.
For successful stain removal:
?
Remove stains
?
Determine the kind of
promptly.
stain,
then follow the recommended treatment in the stain
removal chart below.
?
To pretreat
stains,
use a
prewash product, liquid Detergent, or a paste made from
granular Detergent and water.
unknown stains because HOT water
?
Use COLD water
?
Check care label instructions for
on
treatments to
stain
?
Check for colorfastness
?
Rinse and wash items after stain removal.
by testing
avoid
on
remover on an
can
set
specific
inside
stains.
fabrics.
Follow fabric
care
label
instructions
seam.
Stain Removal
STAIN
Adhesive tape,
rubber cement
chewing gum,
Baby formula, dairy products, egg
Beverages (coffee, tea, soda, juice,
alcoholic beverages)
Blood
Candle wax, crayon
TREATMENT
Apply ice. Scrape off excess. Place stain face down on paper towels.
nonflammable dry cleaning fluid.
Use product containing enzymes to pretreat or soak stains.
Rinse with COLD water. Rub with bar soap. Or pretreat
bleach safe for fabric.
soak in WARM water using product
Collar or cuff soil, cosmetics
Pretreat with
Grease, oil, tar (butter, fats, salad
dressing, cooking oils, car grease,
motor oils)
Ink
Mildew, scorch
Mud
Mustard, tomato
Nail polish
Paint, varnish
Rust, brown or yellow
discoloration
Shoe polish
or
soak with
product containing enzymes. Wash using
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Pretreat
Grass
prewash stain remover or
Pretreat stain. Wash using COLD water and bleach safe for fabric.
Chocolate
Dye transfer on white fabric
Saturate with
or
containing enzymes. Wash using bleach
safe for fabric.
prewash stain remover or rub with bar soap.
Use packaged color remover. Wash using bleach safe for fabric.
Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
using hottest water safe for fabric.
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
mildewed fabrics may be permanently damaged.
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
safe for fabric.
BeforStaingWsh
14
F
BeforStaingWsh
unction of each Button
WATER LEVEL BUTTON
BUTTON
(INDICATION OF DETERGENT AMOUNT)
(OPTION)
Use to select Water
?
?
Temperature.
Pressing the button allows
you to select
WARM
HOT
?
COLD
LEFT, DELAY START
(RESERVATION), ALARM INDICATION
TIME
WATER TEMPERATURE
adjust the WATER LEVEL as required. The
appropriate amount of Detergent is shown next to the
WATER LEVEL in the WATER-DETERGENT diagram
WATER LEVEL is automatically selected for FUZZY
Use to
?
The following
COLD
?
respectively.
Default setting is COLD.
LARGE EX-LARGE
SMALL
SMALL
MEDIUM
MEDIUM
LARGE
LARGE
DELAY START INDICATION
(RESERVATION) When DELAY START
(RESERVATION) program is selected, it
indicates the finishing time. (RES.=DELAY)
EX-LARGE
.
During operation, the remaining time
-
settings are indicated as the button is pushed
LARGE
-
is indicated.
(normal) program.
(HOT&COLD)
Time left
?
MEDIUM
Alarm indication -When an error occurs,
an error
message appears to indicate the abnormality.
For example,
indicates that the lid is open.
2hr
1hr
30 min.
(Tubdry)
DELAY START (RESERVATION) BUTTON
AIR DRY
?
?
This button is used for
air-drying of your
laundry.
Air dry selections light up in
sequence
Use to set
?
The time increases when the button is
as
follows.
30min.
button is
2hr.
1hr
30min.
as
the
time.
?
?
pushed.
delayed finishing
pushed.
The following settings
the button is pushed 3
...11
48
?
a
12
14
16
WASH. RINSE. SPIN BUTTON
?
?
are
indicated
4
5
delay time,
?
...46
switch off.
(refer to page 24)
turn the power
The time increases when the
button is
as
3 HOUR.
To cancel
Use when wash, rinse, spin
time need to be adjusted.
?
pressed
If adjustments are needed
during the wash, press the
[start/pause] button before
making any changes.
When the button is pressed
during washing, the remaining
time is displayed.
.
NOTE
*
*
*
*
washing algorithm, the displaying time may be changed during washing-increased by
8minutes at maximum and decreased by 4 minutes at maximum.
If the Detergent quantity is put more than the standard, for increasing the rinsing performance, it automatically
adds rinsing, and the remaining time may be increased.
The standard detected by the sensor changing the algorithm is set by the normal standard. It may not be same to
the washing habit of a specific user. So, it does not matter that the user uses it according to her/his washing habit.
The sensor for a Detergent quantity is designed to detect based on a synthetic Detergent powder. If you put a
liquid one or a natural one or too much bleaching agent, the detecting ability of the sensor may be decreased.
For
optimizing
the
15
WASHING CONDITION INDICATOR
(OPTION)
only operates in FUZZY Program.
During being detected by the sensor, the LED flashes green, orange
and red in turn. And, after detecting, the LED lights a specific color according to
It
?
?
the
detecting condition
as
follows:
If the current washing condition (Detergent quantity, Water Temperature, water quality, etc.) is determined as
better than the standard one, it optimizes the algorithm to save the energy by decreasing washing time/strength,
and the LED automatically turns to red.
If the current washing condition is determined as worse than the standard one, it optimizes the algorithm by
increasing washing time/strength, and the LED automatically turns to orange.
If the current washing condition is determined as equal to the standard one, the algorithm has no change and the
LED turns to green.
AUTO OFF
(POWER) BUTTON
?
?
?
QU CK ASH
CHILD LOCK FUNCTION
?
Use to lock
or
The power goes off automatically about
10 seconds after the wash is finished.
START/ PAUSE BUTTON
PROGRAM BUTTON
unlock the control
buttons to prevent
Use to turn the power on or off.
Push again and power goes on or off
?
?
settings from
?
Use for
selecting wash program.
This button allows you to select 8
different programs for different kinds of
laundry and dirtiness.
being changed by a child.
To lock, push the RINSE and
SPIN buttons simultaneously and
to unlock push them one more
time during the washing process.
?
program selections light up in sequence
follows: FUZZY (NORMAL)
DELICATE
WOOL
(refer to page 25)
QUICK WASH
SILENT
TUB CLEAN
etc.
?
Use to start
or
pause the
washing process.
Repeats start and pause by
pushing the button.
as
JEAN
FAVORITE
FUZZY
(NORMAL)
Select the desired program by
pressing the button.
*
*
*
Because the
detecting ability of the
sensor
may be decreased
by using
it for
a
long time, periodically use
TUB CLEAN course to clean the tub. (refer to page 21)
Even if the water level or the water temperature are changed by the user in FUZZY(Normal)
the sensor will still work. The sensor algorithm may differ according to models.
The control
panel may
differ
according
to
different models.
Program,
BeforStaingWsh
16
Washing
WashingProm
Programs
Add
the
Washing
Programs
Add
the
laundry
FUZZY Wash
1
Detergent
2
4
(Normal Wash)
Used for normal loads, this
mode automatically selects the
most appropriate conditions
and completes the sequence
in one operation. The built-in
sensor detects the size of the
load and the ideal wash
power and wash, rinse and
spin
times
are
set
Add the
appropriate
quantity of Detergent as
indicated
LEVEL next to
WATER DETERGENT.
Or follow the Detergent
manufacturer's instructions
accordingly.
1
3
Use this mode when
time. The
laundry
highly
Select the
QUICK
washing
soiled clothes for
a
WASH
short
under
2.0kg.
appropriate
quantity of Detergent as
by the WATER
LEVEL next to
WATER DETERGENT.
Or follow the Detergent
manufacturer's
panel.
1
Add the
indicated
program
on the
Control
recommended
amount is
5
2
QUICK WASH
lightly
by the WATER
instructions
5
2
3
JEAN Wash
Use Jean program when
washing
Select the
Spread
the
Jeans of different sizes
jean
evenly
the tub
1
3
in
JEAN program
the
Control
on
panel.
5
2
WOOL Wash
Use this program for
Select the
Use neutral
fabrics such
WOOL
Detergent
appropriate
(wash only
as
washing delicate
lingerie and woolens.
"water washable"
program on
the Control
clothes)
Before
washing your woolens check
the care label for the washing
panel.
instructions.
(wash only
water
washable clothes)
DELICATE
Use this program to wash items
requiring a GENTLE WASH
action.
This would include
nylons and dress
light soiled.
blouses,
shirts with
1
3
2
¡GSelect the
DELICATE
program on
the Control
panel.
for the
laundry.
When washing
woolens use a
mild Detergent
recommend- ed
for washing wool.
5
17
Close the lid
3
5
Finish
Caution & Note
6
If water is
wet
already in the tub, or putting
laundry into the tub before starting
will increase the WATER LEVEL.
The pulsator rotates for
8 seconds to detect the
laundry load.
Then the WATER LEVEL
and the amount of
Detergent to be used
will be shown and
water will be supplied.
Water will be
supplied for 2
minutes after the
of the wash to
supplement the
water the laundry
has absorbed.
start
When the wash
program ends, the
buzzer will ring
for 10 seconds
before the Power
goes off
automatically.
4
6
7
4
6
7
With
LEVEL
6
7
can
be set low.
Changes to Water Temperature
(HOT/COLD) and wash level
setting the
6
7
WATER LEVEL
manually, do not set to Medium to
prevent damage to laundry.
Washing with HOT water may damage
the laundry (Water is set to cold
automatically). Ensure that the load is
under 2kg.
In order to avoid damage to laundry,
the spin cycle may appear slow.
This also avoids wrinkles and clothing
may still contain
normal.
4
are
possible during operation.
(refer to page 14)
When
4
WATER
lightweight bulky loads,
¡GBefore starting
the
to
some
water.
wash,
make
This is
sure
that
laundry is washable.
Washing with HOT water may damage
the laundry (Water is set to COLD
automatically).
Ensure that the load is under 2kg.
WashingProm
18
S
WashingProm
OAK Wash
Use this mode to wash normal clothes
SOAK mode can be used with FUZZY
or
or
thick and heavy clothes which are excessively
JEAN or SILENT or FAVORITE program.
1
Press the AUTO OFF
2
Press the PROGRAM button to select the
(POWER) button
dirty.
to turn power on.
washing
SOAK will
not
program.
work in WOOL and
ECONOMY,
DELICATE, TUB CLEAN Program.
3
Press the WASH
button,
to
select SOAK program.
?
?
4
Add the
Keep pressing the WASH button until
the light turns on¡fiSoak¡fl
and¡fiWash¡fl
simultaneously as next image.
SOAK program only works when
socking time is 40, 50 or 60 minutes.
The
Detergent.
appropriate quantity of Detergent marked next to
the
WATER LEVEL of WATER-DETERGENT.
5
Add the
laundry
and press the START/PAUSE button.
The WATER LEVEL and the amount of
used will be shown and water will be
Detergent to be
supplied.
6
Close the lid.
supplied for 2 minutes after the start of the
supplement the absorbed water by the laundry.
Water will be
wash to
Finish
When the wash program ends, the buzzer will ring for
10seconds before the Power goes off automatically.
NOTE
?
Order of Soak-Wash
min
?
?
min
min
timing
min
Soak-Wash
min
min
Select soaking time 40minutes, 50minutes,
the Wash button repeatedly.
or
min
min
60minutes
If necessary, select the times of Rinse and the time for
buttons till you reach the desired times.
Lamp
Off
min
min
min
min
(including washing time) by pressing
Spinning by pressing
the Rinse
or
Spin
min
19
FAVORITE
Wash
Pressing the FAVORITE button allows you to store your FAVORITE
normal cycle memory and then recall it for use at a later time.
1
Press the AUTO OFF
2
Select the FAVORITE program.
3
Select your FAVORITE wash conditions.
(POWER) button
?
wash conditions in the
WashingProm
to turn power on.
Press the WATER TEMP. button to select wash Water
Temperature.
?
Press the WATER LEVEL button to select
WATER LEVEL.
?
Press the WASH
button to
button, the RINSE button & the SPIN
select wash time, rinse time & spin time
respectively you
4
want to store.
Press the START/PAUSE button to store & start your FAVORITE wash
Power turns off automatically after wash.
NOTE
To recall your FAVORITE
1. Press POWER on.
2. Select the FAVORITE
cycle.
the PROGRAM.
3. Press the START/PAUSE button. Then the wash cycle starts.
cycle by pressing
cycle.
20
S
WashingProm
ILENT Wash
Use this program to wash
quietly
in SILENT
especially during
late
1
Press the AUTO OFF
2
Press the PROGRAM button to select SILENT program.
3
Add the
4
Press the START/PAUSE button.
5
Add the
laundry
(POWER) button
into the
washing
night
and dawn.
to turn power on.
tub.
Detergent and close the lid.
NOTE
?
?
SILENT program takes
To reduce noise in
more
longer washing
spinning, spin rpm
moisture than normal.
time than FUZZY
(Normal)
is lower than normal
program.
spinning rpm.
So the
laundry has
21
TUB
CLEAN
If scrud is allowed to
your washer.
in the machine it
build-up
can
result in stains
on
your clothes
or
unpleasant smell
in
Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact
with Detergent, and according to particular degree of dirtiness or quality of water to be use,
in these case, use this program to clean inner tub and outer tub.
1
Press the POWER button to turn power
2
Press the PROGRAM button to select the TUB CLEAN program.
on.
Ex-Large WATER LEVEL is
3
Press the START/PAUSE button.
4
After 10 minutes of water
5
?
Do not
?
Do
?
Left time is
Add the
supplement.
displayed.
oxygenated
bleach (about 300
?
Before
?
When
using
?
this program
remove
this program, do not
using
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid.
lint inside lint filter.
place
any
This program takes about 3 hours to be
this program,
?
After
using
?
After
finishing
?
remove
laundry
?
dirt inside filter.
this program, open the lid of wash to
Do not pour bleach into the tub
Do not leave diluted
Use this program
Do not
use
inside tub.
completed.
directly.
oxygenated bleach
It
might
once
for every month.
this program
repeatedly.
remove
cause
inside tub for
It rusts the tub must drain the remained diluted
?
m
).
Detergent box.
not place any laundry inside tub.
NOTE
?
automatically.
use
Close the lid.
?
set
irritant odor.
damage the
tub.
long time.
oxygenated water out.
an
AditonalFucPrgm
22
A
AditonalFucPrgm
IR DRY
AIR DRY for your
laundary.
1
Press the AUTO OFF
2
Press the AIR DRY button to select the desired
3
Press the START/PAUSE button.
4
Closed the lid.
(POWER) button
to turn power on.
timing.
NOTE
Select "Air
Dry"
30min
Tub
Dry
-Use this mode to
-
-
Do
keep inner tub from getting moldy
not place any laundry inside tub.
Use this mode
once a
-
-
-
-
-
Dry"
by remaining
moisture.
week.
Caution) For better performance, put drain
completely drained out.
Select "Air
caused
hose down to the floor
that water inside will be
so
above 1 hour
Use this mode to reduce the
by minimizing remaining moisture
In general, this is very effective on synthetic items(100% polyester).
Do place laundry which is evenly distributed(Under 2kg).
For normal clothes
For
:
time
drying
on
the
Select 1 hour
synthetic items(100% polyester):
Select 2 hours
or
3 hours(on
some
models)
laundry.
23
1Option
Washing
When you
only
need the Wash, Wash/Rinse
or
Rinse
cycles,
Press the AUTO OFF (Power) button to turn power
2
Only
Wash
Only
these
can
be set
manually.
on.
Only Spin
Rinse
Press the WASH button to
Press the RINSE button to
Press the SPIN button to
select the desired
select the desired times of
select the desired times of
rinse.
spin.
timing.
Only Wash,Rinse
Press the WASH button to
select the desired timing.
Only
Only Rinse,Spin
Press the RINSE button to
select the desired times of
rinse.
Drain
When you want to only
drain, wait until the water
in the washing tub drains
completely.
Press the RINSE button to
select the desired times of
rinse.
Press the SPIN button to
select the desired times of
spin.
this option
for preventing wrinkles of
You
can use
laundry
3
Press the WATER LEVEL
level
of
laundry.
automatically.
amount
button,
If you do not
4
Add the
laundry
5
Press the
START/PAUSE button.
6
Add the
into the
detergent
control the water level according to the
choose anything, it is set the middle water
to
washing
tub.
and close the lid.
NOTE
When
a
Wash, Wash/Rinse or Rinse only option is selected,
after the wash is
completed the water will not
be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained
completely. Then press the START/PAUSE button.
If you do not
specify the water level, then Medium will be automatically selected.
If only Rinse is selected, the process will start from Water Supply.
AditonalFucPrgm
24
D
AditonalFucPrgm
ELAY START
DELAY START
The hours to be
The time
on
the
(RESERVATION) Wash
(RESERVATION) Wash is used to delay the finishing
delayed can be set by the user accordingly.
display is the finishing time not the start time.
time of the
operation.
,
1
Press the POWER button to turn power
2
Press the PROGRAM button to select the
on.
washing
Select the
program.
program for laundry on the Control panel.
This program will not work in WOOL and DELICATE
Program.
3
Press the DELAY START
(RESERVATION) button.
?
The
light will
'
DELAY' turn
'TIME LEFT'
?
on
and
will be marked.
repeatedly to set the desired finishing time.
For example, To finish washing in 9 hours from now, by
make the number 9:00 pressing the DELAY START
(RESERVATION ) button repeatedly.
Press the button
(RES.=DELAY)
4
Add the
Detergent.
The
appropriate quantity of Detergent marked next to the
WATER LEVEL of WATER?DETERGENT.
When the lid is open the machine will not operate, and
alarm signal will remind you to close the lid
5
Add the
laundry
and press the START/PAUSE button.
When you press the START/PAUSE button the
blink.
6
an
supplied for 2 minutes after the start of the
supplement the water the laundry has absorbed.
Close the lid.
Water will be
Finish
The
wash to
light will
washing will be finished according to the delayed time.
NOTE
?
Finishing time can be delayed from 3~48hours. Delaying from3~12hours can be done in
1 hour time intervals
and from 12~48hours in 2 hour time intervals.
?
?
If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.
To select washing time, rinsing times, spinning time, water level, hot/cold or wash power manually, press the
(RESERVATION) button and select the desired option. Then press the START/PAUSE button.
laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning
(The laundry will be wrinkled if left for a long time after spinning.)
DELAY START
?
When the
program
.
25
O
ther Useful Functions
Child Lock Function
If you want to lock all the
child lock
keys to prevent settings from being changed by a child, you can use the
option.
How to Lock
1
Press the POWER button.
Turn Power
2
Press the START/PAUSE button to start
washing.
After all
3
on.
washing conditions
Press both the RINSE button and the SPIN button
are
set
according to
the manual.
simultaneously.
During the wash program, all the buttons are locked
until washing is completed or it is child- lock
function is deactivated manually.
How to Unlock
If you want to unlock
during wash, press both the RINSE
and the SPIN button
simultaneously again.
NOTE
"
"
Mute
& the
remaining
time
are
alternatively shown
on
the
display while they
are
locked.
Option
washing machine
simultaneously.
If you want to
buttons
use
To make buzzer
the
without alarm
signal sounds,
work, press both the WASH and SPIN buttons simultaneously
Seeing Remaining
see
the
one more
time.
Time
remaining time for each process, press one of the WASH,
The remaining time for each process will appear for about 1 second.
To
press both the WASH and SPIN
RINSE and SPIN buttons.
AditonalFucPrgm
26
Placing
Please
Instal ion
1
and
ensure
Leveling
that transit restraint has been removed before
Place the machine
on a
operating your
machine.
flat and firm surface which allows proper clearance.
We suggest a minimum clearance of 2 cm to the
right side and left sides of the machine for ease of
more
than 10
cm
installation.
At the rear,
a
minimum clearance of 10
cm
more
is
than
suggested.
2cm
more
than
2cm
NOTE
If the washer is installed
"
on a
uneven,weak or tilted floor causing excessive vibration,
"
error can happen to it.
spin failure or
It must be placed on a firm and level floor to prevent spin failure.
2
Check that the machine is level
Open the lid
same as
3
and look from above to
see
Top
view of the machine
if it is
shown.
Leveling
the machine
Lift the front of the
washing machine
Adjustable Leg until the
placed in the center.
the
and twist
surface bubble is
Adjustable legs
Installing the Anti-Rat Cover (option) Insert the
front of washing machine and screw it
anti-rat
cover
to be
Level indicator
firmly fixed from the back or
SETTING SCREW
(2pcs)
BACK
ANTI-RAT COVER
Caution
If the power is supplied from a cord extension set or generator, the cord extension set or electrical
portable outlet device should be positioned so that it is not exposed to splashing or ingress of moisture.
27
C
onnecting
Water
Before connecting the Water Supply Hose to the water tap, check the hose type and then
choose the correct instruction here under.
Note that the Water Supply Hose supplied may vary from country to country, Make sure to
connect the blue inlet hose to the COLD water tap, and the orange inlet hose to the HOT
water
Connecting
Water
Hose to water
Supply
the
Untighten
Fixing the
tap
(Normal tap without thread &
screw
type inlet hose.)
Rubber
screw
Untighten the screw of the connector so
tap can be placed in the middle.
2
Instal ion
tap.
Normal Type
1
Supply
Hose
connector to
packing
that the
screw
Connector
the tap
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4
3
screws.
Attach the
water
hose
supply
securely
to
the
connector
Push the water
supply hose vertically upwards
that the rubber seal within the hose
completely to
Connector
so
adhere
can
the tap.
Water
Supply
4
Fixing the
connector to
the
water
supply
Hose
hose
Attach the water
supply hose to the connector and
then tighten it by screwing it to the right.
5
Check the connection of
water
After
connecting the hose, open the tap
for any water leakage.
If the water
leaks, close the tap and
supply
hose and the
connector
to check
start
again
from step 1
NOTE
The
washing machine is
not be reused.
to be connected to the water
mains
using new hose-sets
and old hose-sets should
28
onnecting
C
Instal ion
Normal Type
1
Water
Supply
Hose
(Normal tap without thread & one touch type inlet hose.)
Separate Middle
connector
from Water
Supply
Separate Middle connector from the Water
Supply Hose by pulling the Pressing Rod and the
Pressing Handle that is attached to the Water
Supply Hose.
Hose
Middle
Fixed Sticker
connector
Pressing
Handle
Pressing
Rod
Water
2
Loosen the fixed nuts to connect the connector to the
Untighten the screw of the connector so
tap can be placed in the middle.
Supply
Hose
tap
that the
Rubber
packing
screw
Fixed sticker
NOTE
In
case
tap is too
Guide
large.
plate
If the tap diameter is too large or is square,
untighten the 4 screws and remove the guide
plate.
3
Then follow
Fixing
Rubber
packing
step1.
Connectors to the
Tap
Connector
Push the upper connector up till the rubber
packing is in tight contact with the tap. Then
tighten the 4 screws.
4
Fixing Upper
Connector and Middle Connector
Remove the fixed sticker in between the
and Middle Connectors.
Connector
Upper
Tighten the connectors
Middle
by holding one connector and twist middle
connector to the right.
5
Connecting Middle
Connector
Fixed sticker
Connector and Water
Supply
pressing rod of the Water Supply
Hose which was separated from middle connector
(refer to Step1) and then join it to the middle
Connector
Middle
Connector
Hose
Press down the
Pressing
rod
connector.
Water
6
Check for
water
leakage
After
connecting the hose, open the tap to check
for any water leakage.
If the connection
leaks, close the tap and
start
again from step 1.
If you skip step 1, water leakage may occur.
Supply
Hose
Pressing
handle
29
Screw
1
Attach the
water
Push the water
packing
Instal ion
Type
supply
supply hose up
within the hose
can
so
hose
to
the tap.
that the rubber
adhere
completely
to
the tap.
Water
tap
Rubber
Water
2
Connect the water
supply
Connect the water
hose
supply hose to the tap
tighten it by screwing it to the right.
3
Check
water
connecting the hose,
for any water leakage.
?
Water
Supply
the tap.
and then
leakage.
After
Connecting
to
Packing
open the tap to check
Supply
Connect the water
Hose to the machine
supply hose to
inlet valve of
washing machine, and then lock it by turning
the hose connecting part.
the
?
Check
to
see
if there is
a
rubber seal inside the
Hose connector
connector.
Rubber seal
Hose
30
Connecting
Drain Hose
Before connecting Drain Hose, check your Drain Hose model and choose the correct
instructions.
Instal ion
Pump Model
1
Fit the end of the drain hose to the outlet of the
2
Put the other end of the drain hose over the
drain pump and
tighten the clamp.
standpipe or
wash tub.
Hose
Guide
Within 50mm
0.9~1.2m
Drain Hose
NOTE
To prevent siphoning, the drain hose should not extend more than 50 mm from the end of the hose
The discharge height should be approximately 0.9
1.2 m from the floor.
~
Non-Pump Model
1
Before
connecting
Ensure that the hose
clip is
set
as
indicated here.
Clip
2
Connect the Elbow Hose
Push the elbow hose toward the
body of the
washing machine.
3
Place the Drain Hose
change the direction of the hose, pull out the
elbow hose and change the direction.
Repeat Step 2.
To
guide.
31
G
rounding
Method
Earth wire should be connected.
If the earth wire is not connected, there is
the current leakage
possible
a
danger
of electric shock caused
by
.
Grounding
Method with Ground insert space Terminal
Ground
If the AC current outlet has
ground terminal, then
separate grounding is not required. Note that AC power
outlet configurations may differ from country to country
a
Terminal
Outlet with
ground
terminal.
Caution
CAUTION
concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers
only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's
manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord
replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the appliance.
Other
Grounding
Method
Burying Copper Plate
Connect the Ground Wire
bury it
Plate and
Ground
Copper
more than 75cm in the ground.
to
a
Ground Wire
75cm
Ground
Using Ground
Copper
Wire
ground Wire to the socket provided
exclusively for Grounding.
Connect the
Using
Plate
Ground
Wire
Short Circuit Breaker
a
If grounding methods described above
possible,
employed
a
Short-circuit
not
are
separate circuit breaker should be
and installed by a qualified electrician
breaker
Caution
?
?
To prevent a possible explosion, do not connect ground to a gas pipe
Do not connect ground to telephone wires or lightning rods. This may be
storms
?
Connecting ground to plastic has no
effect
?
Ground wires should be connected when
an
extension cord is used.
dangerous during electrical
CarendMitc
32
Cleaning
CarendMitc
Cold water
?
and Maintenance
washing
always use COLD water,
If you
we
recommend that
intervals e.g. every 5th wash should be
at least
a
a
WARM
WARM
or
HOT wash be used
a
regular
as
sand),
at
one.
When you have finished
?
?
Turn off taps to prevent the chance of flooding should
Always unplug the power cord after use.
When water supply into the tub is not clean
filter in the inlet valve occasionally.
(The figure of power cord and
water
or
the filter is
a
hose burst.
clogged
with
to the
tap may vary according
particles (such
clean the
country)
To Clean the Filter in the Inlet Valve
1
Close the tap before turning off the power.
Select both HOT/COLD and then press the
2
Turn off the power before
pulling out the cord.
4
Replace the filter after cleaning it.
[START/PAUSE] button to remove water
from the machine completely.
3
After
removing the water supply
hose pull out the filter.
Then
use a
brush to clean the filter.
NOTE
?
Before
cleaning
the
filter,
the
impurities
in the water
supply
hose should be removed.
To Clean the Lint Filter
1
2
Pull out the lint filter from
3
Turn the net inside out
the tub in the direction
to clean the filter and
shown below.
rinse it with water.
Replace- the filter to the
original location. Push the
lip of the filter until a pop
sound is heard.
NOTE
?
If the lint filter is torn
To Clean the
1
or
damaged, purchase
a new one
from LG service center.
Pump casing (for pump model)
Place a towel on the
floor under the drain
pump cap. Excess
water may flow out.
2
Turn the cap
counter-
clockwise and
pull it out.
Cap
3
Remove any foreign
objects and fluff inside
pump casing and from the
4
filter.
Replace the cap. Insert the filter along
the guide ribs inside the pump casing.
Filter must face the guide ribs inside
pump casing and securely turn the cap
clockwise.
Filter
Guide rib
Filter
NOTE
?
Check if water leaks after reassembling. (The Rubber ring is in the
cap)
33
C
and Maintenance
leaning
When there is
?
?
?
a
fear of
CarendMitc
freezing
Close the water taps and remove the Water Supply Hose.
Remove the water which remains in the water supply.
Lower the drain hose and drain the water in the bowl and the drain hose
by spinning.
If frozen
?
?
?
and immerse it in HOT water at approx.. 40˚C.
Pour approx.. 2 liters of HOT water at approx.. 40˚C, into the bowl and let it stand for 10 minutes.
Connect the water supply hose to the water tap and confirm that the washing machine performs the
Remove the water
and
supply
Wash Inner-tub
supply hose,
drainage of water.
Leave the lid open after
the inner-tub
use a
not use harsh or
Inlet Hoses
Vacations
Cleaning the
Be
?
with
liquid Detergent,
then rinse.
(Do
surface with
is shut off at faucets. Drain all water from hoses if weather will
supply
freezing.
Inside of your Washer
regular COLD
do
or
it is very
washing,
water
important that you occasionally clean the
Fill your washer with HOT water.
Add about two cups of
a
powdered Detergent that contains phosphate.
Let it operate for several minutes.
?
Stop the washer,
?
After
Or
use
soaking,
open the lid and leave it to soak
drain the washer and
TUB CLEAN PROGRAM
run
it
Products that
Concentrated bleaches and
?
Hydrocarbon
?
Some pretreatment sprays
?
Use of
normal
cycle.
during this procedure.
machine
diaper sanitizer will cause damage to
we
petrol, paint thinners
the
paintwork and components
of your washer.
lacquer thinners, etc. can dissolve plastic and blister paint
(Be careful when washing garments stained with these solvents as they are flammable DO NOT put them in
washer or dryer.)
but
solvents i.e.
a
periodically.
might damage your washing
?
overnight.
through
We do not recommend that you wash clothes
or
liquids
can
Do not
and
damage your washer's
control
panel.
in your washer may cause staining of the plastic components. The dye will not damage the machine
suggest you thoroughly clean your washer afterwards. We do not recommend the use of dye strippers in
dyes
your washer.
?
dampened
want to clean
gritty cleaners.)
water
sure
If you use fabric softener
inside of your washer.
?
clean soft cloth
evaporate. If you
connecting washer to faucet should be replaced every 5 years.
Immediately wipe off any spills. Wipe with damp cloth. Try not to hit
sharp objects.
be below
?
to allow moisture to
Hoses
Exterior
Long
washing
use
your washer lid
as a
work surface.
34
Common
washing problems
Many washing problems involve poor soil & stain removal, residues of lint
fabric damage. For satisfactory washing results, follow these instructions.
Troubleshting
and scum, and
WASH PROBLEM
Problems
Solutions & Preventive Measures
Possible Causes
Poor soil
?
removal
?
Not
enough Detergent
Wash Water Temperature
too low.
the washer
Overloading
?
Incorrect wash
?
Use correct amount of Detergent for load
Use WARM
or
Different Water
Temperature may be required according
type. (refer to page 10)
?
pretreat stain
Reduce load size.
?
Wash with JEAN
Do not
amount of
HOT water for normal soil.
cycle
sorting
Incorrect
size,
soil and water Hardness.
?
?
?
?
soil
or
SOAK & JEAN wash
to
cycle for heavy
soiled
?
?
laundry.
Separate heavily soiled items from lightly soiled ones.
Pretreat stain and heavy soil according to directions shown
on
Blue Stains
?
Undiluted fabric softener
dispensed directly
onto
?
?
fabric
page 9.
Rub the stain with bar soap. Wash.
Do not overfill fabric softener
liquid fabric
softener
See page 12 for
Black or gray
marks on
clothes
Yellow or
brown rust
?
A
caused
buildup
by the
?
interaction of fabric softener
and
Detergent
can
flake off
?
and mark clothes
?
Not
?
Iron
water
stains
or
manganese in
supply,
water
?
instructions.
more
Keep the recommendations against Scrud(waxy buildup).
(refer to scrud page12.)
Use correct amount of Detergent for load
size,
amount of soil
To restore discolored load of whites,
use
rust
remover
safe
for fabric.
pipes,
water heater
directly onto fabric.
and water Hardness.
enough Detergent
or
dispenser and do not pour
?
Install
nonprecipitating water
softener
or an
iron filter in
supply system for an ongoing problem.
Before washing, run water for a few minutes to clear lines.
your water
?
Lint
?
?
?
Residue
or
Detergent
Incorrect
sorting
Tissues left in pocket
Overloading the washer
?
Overloading
?
Undissolved
?
Use too
the washer
Detergent
much Detergent
?
or
Incorrect
use
of chlorine
?
?
Unfastened
zippers,
hooks, buckles
Ribs, tears and broken
?
Overloading the washer
Degradation of fabric
synthetic fabrics and remove tissues
See page 9 for sorting and caring
Do not overload the washer
?
Do not overload the washer.
?
Some
Detergents need to be pre-dissolved, check the Detergent
instructions.
?
?
?
threads
?
towels, flannelette sheets, separately
?
bleach.
snags
eg
pockets before wash.
before loading.
?
Holes, tears,
givers
from lint collectors eg
?
?
Wash lint
?
Try pre-dissolving the Detergent.
Increase Water Temperature
using HOT water safe for fabric.
Use proper amount of Detergent.
Never pour chlorine bleach
directly on fabric.
See page 11 for adding liquid bleach.
Fasten zippers, hooks, and buckles.
Remove objects in pockets. See page 9 for caring before
loading.
Do not overload the washer.
in
35
T
roubleshooting
Before
calling
Symptom
Water
Supply
Failure
for service, check the
Error
problem against
Message
.
.
.
.
.
Drainage
Troubleshting
Check up
.
Failure
the list bellows.
.
.
.
Is the water tap shut off?
Is the water supply cut off ?
Is the tap
or
water
supply hose frozen
?
Is the water pressure low or is the filter of the inlet
valve clogged with impurities?
Is the Hot hose connected to cold?
Is the Cold hose connected to hot?
Is the drain hose
positioned correctly?
Is the drain hose bent or placed too high?
Is the internal part of the hose
or
drain pump
(only pump model) clogged with impurities?
.
Spin Failure
Door(Lid) Open
.
Is the
laundry evenly balanced?
.
Is the
washing machine placed on a flat surface?
.
Is the lid closed?
.
Internal sensing
failure
Power failure
Overflow failure
Check if electric power has gone off.
Please call your nearest LG Electronics service center
for help.
36
Terms
of
Warranty
What Is Not Covered:
?
?
?
?
trips to your home to teach you how to use the product.
If the product is connected to any voltage other than that shown on the rating plate.
If the fault is caused by accident, neglect, misuse or Act of God.
If the fault is caused by factors other than normal domestic use or use in
Service
accordance with the owner's manual.
change the set-up of the product.
If the fault is caused by pests for example, rats or cockroaches etc..
Noise or vibration that is considered normal for example water drain sound, spin
sound, or warming beeps.
Correcting the installation for example, levelling the product, adjustment of drain.
Normal maintenance which recommended by the owner's manual.
Removal of foreign objects / substances from the machine, including the pump and
inlet hose filter for example, grit, nails, bra wires, buttons etc.
Replace fuses in or correct house wiring or correct house plumbing.
Correction of unauthorized repairs.
Incidental or consequential damage to personal property caused by possible defects
with this appliance.
If this product is used for commercial purpose, it is not warranted.
(Example : Public places such as public bathroom, lodging house, training center,
dormitory)
?
Provide instruction
on use
of product
or
?
?
?
?
?
?
?
?
?
If the
product is installed outside the normal service area, any cost of transportation
involved in the repair of the product, or the replacement of a defective part, shall be
borne by the owner.
37
S
pecification
Specifaton
2hr
1hr
30
min.
(Tubdry)
H
D
W
Model
WFT(R,N,S,C,F)10(1)C64(5)D(E)C(H,P,D,E,F,M)
WF-T1250TD, WF-T1391TP, WF-TS1688TC
Size
632(w)
x
670(D)
x
1005(H) : WFT(R,N,S,C,F)10(1)C64(5)DC(H,P,D,E,F,M)
632(w)
x
670(D)
x
1020(H) : WFT(R,N,S,C,F)10(1)C64(5)EC(H,P,D,E,F,M)
WF-T1250TD, WF-T1391TP, WF-TS1688TC
Water tab pressure
In
to
30
-
800 kPa
(0.3
-
8.0
kgf/cm2)
continuing effort to improve the quality of our appliances,
the appliance without revising this manual.
our
it may be necessary to make
changes
Memo
P/No.: 3828EA3030F
Download PDF

advertising