LG | 32LU340C | LG 32LU340C Owner’s Manual

LED TV
LU34*
LU54*
12
14
16
20
AAA
X2
(M4 X L16)
: Depending on model /
www.lg.com
1
2
3
4
ANTENNA/
CABLE IN
HDMI IN
USB IN
H/P OUT
H/P OUT
OPTICAL DIGITAL
AUDIO OUT
PCMCIA CARD SLOT
OPTICAL DIGITAL
AUDIO OUT
CLOCK
COMPONENT IN
AV IN
COMPONENT IN
VIDEO/Y PB
VIDEO
AV IN
PR L/MONO AUDIO R
AUDIO
VIDEO/Y PB
PR L/MONO AUDIO R
VIDEO L/MONO AUDIO R
HDMI-DVI IN
RGB IN
RGB IN
HDMI IN
VIDEO/Y PB
PR L/MONO AUDIO R
AUDIO OUT
VIDEO/Y PB
DVI OUT
PR L/MONO AUDIO R
AUDIO OUT
RGB OUT
1
2
3
4
1
2
3
4
0
1
2
A
E
D
B
G
F
32LU340C-TB
32LU540H-TB
C
A
B
C
D
E
F
739
472
168
441
84.0
4.90
Power requirement /
F
G
4.85
AC 100-240 V ~ 50 / 60 Hz
OWNER’S MANUAL
Safety and Reference
LED TV*
LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain
it for future reference.
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
Warning! Safety Instructions
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
•• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS
WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
•• Do not place the TV and/or remote control in the following
environments:
-- Keep the product away from direct sunlight.
-- An area with high humidity such as a bathroom
-- Near any heat source such as stoves and other devices that produce
heat.
-- Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil.
-- An area exposed to rain or wind.
-- Do not expose to dripping or splashing and do not place objects
filled with liquids, such as vases, cups, etc. on or over the apparatus
(e.g., on shelves above the unit).
-- Near flammable objects such as gasoline or candles, or expose the
TV to direct air conditioning.
-- Do not install in excessively dusty places.
Otherwise, this may result in fire, electric shock, combustion/
explosion, malfunction or product deformation.
2
•• Ventilation
-- Install your TV where there is proper ventilation. Do not install in a
confined space such as a bookcase.
-- Do not install the product on a carpet or cushion.
-- Do not block or cover the product with cloth or other materials
while unit is plugged in.
•• Take care not to touch the ventilation openings. When watching the
TV for a long period, the ventilation openings may become hot.
•• Protect the power cord from physical or mechanical abuse, such as
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and the point where the
cord exits the device.
•• Do not move the TV whilst the Power cord is plugged in.
•• Do not use a damaged or loosely fitting power cord.
•• Be sure do grasp the plug when unplugging the power cord. Do not
pull on the power cord to unplug the TV.
•• Do not connect too many devices to the same AC power outlet as this
could result in fire or electric shock.
•• Disconnecting the Device from the Main Power
-- The power plug is the disconnecting device. In case of an
emergency, the power plug must remain readily accessible.
•• Do not let your children climb or cling onto the TV. Otherwise, the TV
may fall over, which may cause serious injury.
•• Outdoor Antenna Grounding (Can differ by country):
-- If an outdoor antenna is installed, follow the precautions below.
An outdoor antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits, or
where it can come in contact with such power lines or circuits as
death or serious injury can occur.
Be sure the antenna system is grounded to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A.
provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National Electrical Code, ANSI/
NFPA 70
•• Batteries
-- Store the accessories (battery, etc.) in a safe location out of the
reach of children.
-- Do not short circuit, disassemble, or allow the batteries to
overheat. Do not dispose of batteries in a fire. Batteries should not
be exposed to excessive heat.
•• Moving
-- When moving, make sure the product is turned off, unplugged, and
all cables have been removed. It may take 2 or more people to carry
larger TVs. Do not press or put stress on the front panel of the TV.
Otherwise, this may result in product damage, fire hazard or injury.
•• Keep the packing anti-moisture material or vinyl packing out of the
reach of children.
•• Do not allow an impact shock, any objects to fall into the product,
and do not drop anything onto the screen.
•• Do not press strongly upon the panel with a hand or a sharp
object such as a nail, pencil, or pen, or make a scratch on it. It may
cause damage to screen.
•• Cleaning
-- When cleaning, unplug the power cord and wipe gently with a
soft/dry cloth. Do not spray water or other liquids directly on the
TV. Do not clean your TV with chemicals including glass cleaner, any
type of air freshener, insecticide, lubricants, wax (car, industrial),
abrasive, thinner, benzene, alcohol etc., which can damage the
product and/or its panel. Otherwise, this may result in electric
shock or product damage.
ENGLISH
•• Grounding (Except for devices which are not grounded.)
-- TV with a three-prong grounded AC plug must be connected to a
three-prong grounded AC outlet. Ensure that you connect the earth
ground wire to prevent possible electric shock.
•• Never touch this apparatus or antenna during a lightning storm. You
may be electrocuted.
•• Make sure the power cord is connected securely to the TV and wall
socket if not secured damage to the Plug and socket may occur and in
extreme cases a fire may break out.
•• Do not insert metallic or inflammable objects into the product. If a
foreign object is dropped into the product, unplug the power cord
and contact the customer service.
•• Do not touch the end of the power cord while it is plugged in. You
may be electrocuted.
•• If any of the following occur, unplug the product immediately
and contact your local customer service.
-- The product has been damaged.
-- If water or another substance enters the product (like an AC
adapter, power cord, or TV).
-- If you smell smoke or other odors coming from the TV
-- When lightning storms or when unused for long periods of time.
Even the TV is turned off by remote control or button, AC power
source is connected to the unit if not unplugged in.
•• Do not use high voltage electrical equipment near the TV (e.g., a bug
zapper). This may result in product malfunction.
•• Do not attempt to modify this product in any way without written
authorization from LG Electronics. Accidental fire or electric shock
can occur. Contact your local customer service for service or repair.
Unauthorized modification could void the user’s authority to operate
this product.
•• Use only an authorized attachments / accessories approved by
LG Electronics. Otherwise, this may result in fire, electric shock,
malfunction, or product damage.
•• Never disassemble the AC adapter or power cord. This may result in
fire or electric shock.
•• Handle the adapter carefully to avoid dropping or striking it. An
impact could damage the adapter.
•• To reduce the risk of fire or electrical shock, do not touch the TV with
wet hands. If the power cord prongs are wet or covered with dust, dry
the power plug completely or wipe dust off.
3
ENGLISH
Preparing
Separate Purchase
•• If the TV is turned on for the first time after it was shipped from the
factory, initialization of the TV may take a few minutes.
•• Image shown may differ from your TV.
•• Your TV’s OSD (On Screen Display) may differ slightly from that shown
in this manual.
•• The available menus and options may differ from the input source or
product model that you are using.
•• New features may be added to this TV in the future.
•• The device must be easily accessed to a location outlet near the
access. Some devices are not made by turning on / off button, turning
off the device and unplugging the power cord.
•• The items supplied with your product may vary depending on the
model.
•• Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.
•• For an optimal connection, HDMI cables and USB devices should have
bezels less than 10 mm thick and 18 mm width. Use an extension
cable that supports USB if the USB cable or USB memory stick
does not fit into your TV’s USB port.
Separate purchase items can be changed or modified for quality
improvement without any notification. Contact your dealer to buy these
items. These devices only work with certain models.
B
B
A
A
* A <
= 10 mm
* B <
= 18 mm
•• Use a certified cable with the HDMI logo attached.
•• If you do not use a certified HDMI cable, the screen may not display or
a connection error may occur. (Recommended HDMI Cable Types)
-- High-Speed HDMI®/TM Cable (3 m or less)
-- High-Speed HDMI®/TM Cable with Ethernet (3 m or less)
The model name or design may be changed depending on the upgrade
of product functions, manufacturer’s circumstances or policies.
Wall Mounting Bracket
Make sure to use screws and wall mount bracket that meet the VESA
standard. Standard dimensions for the wall mount kits are described in
the following table.
A
B
Model
24LU34*
28LU34*
VESA (A x B) (mm)
Standard screw
Number of screws
Wall mount bracket
75 x 75
M4 X L10
4
LSW140B
32/43LU34*
100 x 100
M4 X L10
4
LSW140B
49LU34*
32/43LU54*
200 x 200
M6
4
LSW240B
49LU54*
300 x 300
M6
4
OLW480B
MSW240
MSW240
Model
VESA (A x B) (mm)
Standard screw
Number of screws
Wall mount bracket
4
Mounting on a Table
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
1 Lift and tilt the TV into its upright position on a table.
• Leave a 10 cm (minimum) space from the wall for proper
ventilation.
•• It is recommended to move the TV in the box or packing material that
the TV originally came in.
•• Before moving or lifting the TV, disconnect the power cord and all
cables.
•• When holding the TV, the screen should face away from you to avoid
damage.
ENGLISH
Lifting and moving the TV
10 cm
10 cm
10 cm
10 cm
10 cm
•• Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.
(Depending on model)
2 Connect the power cord to a wall outlet.
•• When transporting a large TV, there should be at least 2 people.
•• When transporting the TV by hand, hold the TV as shown in the
following illustration.
•• When transporting the TV, do not expose the TV to jolts or excessive
vibration.
•• When transporting the TV, keep the TV upright, never turn the TV on
its side or tilt towards the left or right.
•• Do not apply excessive pressure to cause flexing / bending of frame
chassis as it may damage screen.
•• When handling the TV, be careful not to damage the protruding
buttons.
•• Avoid touching the screen at all times, as this may result in
damage to the screen.
•• Do not move the TV by holding the cable holders, as the
cable holders may break, and injuries and damage to the TV
may occur.
•• When attaching the stand to the TV set, place the screen
facing down on a cushioned table or flat surface to protect
the screen from scratches.
•• Do not apply foreign substances (oils, lubricants, etc.) to the
screw parts when assembling the product.
(Doing so may damage the product.)
•• If you install the TV on a stand, you need to take actions
to prevent the product from overturning. Otherwise, the
product may fall over, which may cause injury.
•• Do not use any unapproved items to ensure the safety and
product life span.
•• Any damage or injuries caused by using unapproved items
are not covered by the manufacturer’s warranty.
•• Make sure that the screws are inserted correctly and fastened
securely. (If they are not fastened securely enough, the TV
may tilt forward after being installed.) Do not use too much
force and over tighten the screws; otherwise screw may be
damaged and not tighten correctly.
•• If a television is not positioned in a sufficiently stable
location, it can be potentially hazardous due to falling. Many
injuries, particularly to children, can be avoided by taking
simple precautions such as:
»» Using cabinets or stands recommended by the
manufacturer of the television.
»» Only using furniture that can safely support the television.
»» Ensuring the television is not overhanging the edge of the
supporting furniture.
»» Not placing the television on tall furniture (for example,
cupboards or bookcases) without anchoring both the
furniture and the television to a suitable support.
»» Not standing the televisions on cloth or other materials
placed between the television and supporting furniture.
»» Educating children about the dangers of climbing on
furniture to reach the television or its controls.
5
Attaching the TV to a Desk
The TV should be attached to a desk so it cannot be pulled in a forward/
backward direction, potentially causing injury or damaging the product.
ENGLISH
A type
Using the Kensington security
system
•• Image shown may differ from your TV.
The Kensington security system connector is located at the rear of the
TV. For more information of installation and using, refer to the manual
provided with the Kensington security system or visit
http://www.kensington.com. Connect the Kensington security system
cable between the TV and a table.
4-Screws
(Not supplied with TV)
Stand
(Depending on model)
Desk
(Depending on model)
Securing the TV to a Wall
•• Screw: M5 x L (*L: Table depth + 8~10 mm)
ex) Table depth: 15 mm, Screw: M5 x L25
B type
(Depending on model)
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
• If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
Match the location of the wall bracket and the eye-bolts on the rear
of the TV.
3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
Make sure to keep the rope horizontal with the flat surface.
2-Screws for Stand Fixing,
2-Washers for Stand Fixing,
2-Nuts for Stand Fixing
(Supplied with TV)
Stand
Desk
(Depending on model)
6
•• Use a platform or cabinet that is strong and large enough to support
the TV securely.
•• Brackets, bolts and ropes are not provided. You can obtain additional
accessories from your local dealer.
Mounting to the Wall
10 cm
10 cm
ENGLISH
Attach an optional wall mount bracket at the rear of the TV carefully
and install the wall mount bracket on a solid wall perpendicular to
the floor. When you attach the TV to other building materials, please
contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing fixed wall mounts.
•• When installing the wall mounting bracket, it is recommended to
cover the stand hole using tape, in order to prevent the influx of dust
and insects. (Depending on model)
Stand hole
m
10 c
10 cm
10 cm
(Depending on model)
•• Remove the stand before installing the TV on a wall mount
by performing the stand attachment in reverse.
•• For more information of screws and wall mount bracket,
refer to the Separate purchase.
•• If you intend to mount the product to a wall, attach VESA
standard mounting interface (optional parts) to the back
of the product. When you install the set to use the wall
mounting bracket (optional parts), fix it carefully so as not
to drop.
•• When mounting a TV on the wall, make sure not to install
the TV by hanging the power and signal cables on the back
of the TV.
•• Do not install this product on a wall if it could be exposed
to oil or oil mist. This may damage the product and cause
it to fall.
•• Screw length from outer surface of back cover should be under 8 mm.
(Only 24/28LU340*)
Wall mount Pad
Back Cover
Wall mount Pad
Back Cover
Standard screw
: M4 x L10
Max. 8 mm
7
Connections
ENGLISH
Connect various external devices to the TV and switch input modes to
select an external device. For more information of external device’s
connection, refer to the manual provided with each device.
Antenna/Cable
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
•• Use a signal splitter to use more than 2 TVs.
•• If the image quality is poor, install a signal amplifier properly to
improve the image quality.
•• If the image quality is poor with an antenna connected, try to realign
the antenna in the correct direction.
•• An antenna cable and converter are not supplied.
Satellite dish
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω). (Depending on model)
CI module
View the encrypted (pay) services in digital TV mode. (Depending on
model)
•• Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can cause
damage to the TV and the PCMCIA card slot.
•• If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service
Operator.
Other connections
Connect your TV to external devices. For the best picture and audio
quality, connect the external device and the TV with the HDMI cable.
Some separate cable is not provided.
HDMI
•• Supported HDMI Audio format (Depending on model):
Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz),
PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)
8
External Devices
Available external devices are: Blu-ray player, HD receivers, DVD players,
VCRs, audio systems, USB storage devices, PC, gaming devices, and
other external devices.
•• The external device connection may differ from the model.
•• Connect external devices to the TV regardless of the order of the TV
port.
•• Refer to the external equipment’s manual for operating instructions.
•• If you connect a gaming device to the TV, use the cable supplied with
the gaming device.
•• In PC mode, there may be noise associated with the resolution,
vertical pattern, contrast or brightness. If noise is present, change the
PC output to another resolution, change the refresh rate to another
rate or adjust the brightness and contrast on the PICTURE menu until
the picture is clear.
•• In PC mode, some resolution settings may not work properly
depending on the graphics card.
•• When connecting via a wired LAN, it is recommended to use a CAT 7
cable. (Only when
port is provided.)
External Speakers
Method of Volume control Port
(Depending on model)
•• Cable Spec.
VOLUME
CONTROL
GND / UP / DOWN
Control port for Speaker out
+
UP
-
ENGLISH
Each Up / Down pin
is pulled to 3.3 V with
CPU GPIO.
EXTERNAL
SPEAKER OUT
CPU detects transition
from 3.3 V to GND level
for volume control.
DOWN
GND
RIGHT
LEFT
GND
: Depending on model
(Depending on model)
•• Use only with the 3 Pole 3.5 mm Stereo Jack.
•• Do not connect your headphones or earphones to the port
for connecting an external speaker.
9
Using Button
Network
Wired network connection
ENGLISH
This TV can be connected to a Pro:Centric server via the LAN port. After
making the physical connection, the TV needs to be set up for network
communication.
You can simply operate the TV functions, using the button.
Connect the LAN port of the Modem or Router from Pro:Centric server
to the LAN port on the TV.
Basic functions
1
Power On (Press)
Power Off1 (Press and Hold)
Menu Control (Press1)
Menu Selection (Press and Hold2)
Broadband Modem
Pro:Centric Server
Router
1 You can access and adjust the menu by pressing the button when
TV is on.
2 You can use the function when you access menu control.
Broadband Modem
Adjusting the menu
Pro:Centric Server
When the TV is turned on, press the
the Menu items using the button.
button one time. You can adjust
Turns the power off.
C onnect the LAN port of the Modem or Router to the LAN port
on the TV.
•• Do not connect a modular phone cable to the LAN port.
•• Since there are various connection methods, please follow
the specifications of your telecommunication carrier or
internet service provider.
10
Changes the input source.
Scrolls through the saved programmes.
Adjusts the volume level.
Adjusting the Angle of the
TV to suit view
Using Remote Control
(Depending on model)
20˚
20˚
ENGLISH
Swivel 20 degrees to the left or right and adjust the angle of the TV to
suit your view.
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA)
matching the and ends to the label inside the compartment, and
close the battery cover. To remove the batteries, perform the installation
actions in reverse.
Make sure to point the remote control toward the remote control sensor
on the TV.
(Depending on model)
•• When adjusting the angle of the product, watch out for your
fingers.
-- Personal injury may occur if hands or fingers are pinched.
If the product is tilted too much, it may fall, causing
damage or injury.
(Some buttons and services may not be provided depending on models
or regions.)
11
ENGLISH
(POWER) Turns the TV on or off.
Adjusts the brightness of the screen to reduce
energy consumption.
Selects an AV mode.
Changes the input source.
Selects Radio, TV and DTV programme.
Number buttons Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
Adjusts the volume level.
Accesses your favourite programme list.
Resizes an image.
Mutes all sounds.
-- Pressing and holding the button accesses the Accessibility
menu. (Only LU34**)
Scrolls through the saved programmes.
Moves to the previous or next screen.
Shows programme guide.
Displays and removes hotel interactive menu.
Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus
or options.
Selects menus or options and confirms your input.
Accesses the main menus.
(BACK) Returns to the previous level.
Clears on-screen displays and return to TV viewing.
These access special functions in some
menus.
Teletext buttons (
) These buttons are used for
teletext.
Recalls your preferred subtitle in digital mode.
Control buttons (
) Controls media contents.
Accesses the AV devices connected with the HDMI cable
through HDMI-CEC. Opens the SIMPLINK menu.
Accesses the Quick menus.
Audio descriptions function will be enabled.
Sets the alarm function. (Only for LU5**H series)
12
(Some buttons and services may not be provided depending on models
or regions.)
(POWER) Turns the TV on or off.
Selects Radio, TV and DTV programme.
Recalls your preferred subtitle in digital mode.
Audio descriptions function will be enabled.
Resizes an image.
(INPUT) Changes the input source.
Number buttons Enters numbers.
Accesses the saved programme list.
Returns to the previously viewed programme.
Adjusts the volume level.
Accesses your favourite programme list.
Shows programme guide.
(MUTE) Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen.
Teletext buttons (
) These buttons are used for
teletext.
(HOME) Accesses the Home menu.
(Settings) Accesses the Settings menu.
Accesses the Quick menus.
•• Do not mix new batteries with old batteries. This may cause
the batteries to overheat and leak.
•• Failure to match the correct polarities of the battery may
cause the battery to burst or leak, resulting in fire, personal
injury, or ambient pollution.
•• This apparatus uses batteries. In your community there
might be regulations that require you to dispose of these
batteries properly due to environmental considerations.
Please contact your local authorities for disposal or recycling
information.
•• Batteries inside or inside the product shall not be exposed to
excessive heat such as sunshine, fire or the like.
•• In Analogue TV and some countries, some remote control
buttons may not work.
Troubleshooting
The software version can be updated for improvement in performance.
ENGLISH
Navigation buttons (up/down/left/right) Scrolls through menus
or options.
Selects menus or options and confirms your input.
Returns to the previous level.
Clears on-screen displays and returns to TV viewing.
Views the information of the current programme and screen.
Starts to record and displays record menu. (Only Time
MachineReady supported model) (Depending on model)
Control buttons (
) Controls media contents.
These access special functions in some menus.
Customer needs to ensure the compatibility of customer’s equipment
with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Cannot control the TV with the remote control.
•• Check the remote control sensor on the product and try again.
•• Check if there is any obstacle between the product and the remote
control.
•• Check if the batteries are still working and properly installed ( to
, to ).
No image display and no sound is produced.
•• Check if the product is turned on.
•• Check if the power cord is connected to a wall outlet.
•• Check if there is a problem in the wall outlet by connecting other
products.
The TV turns off suddenly.
•• Check the power control settings. The power supply may be
interrupted.
•• Check if the auto-off function is activated on the settings related
time.
•• If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI), no signal is detected.
•• Turn the TV off/on using the remote control.
•• Reconnect the RGB/HDMI cable.
•• Restart the PC with the TV on.
13
Abnormal display
ENGLISH
•• If the product feels cold to the touch, there may be a small “flicker”
when it is turned on. This is normal, there is nothing wrong with
product.
•• This panel is an advanced product that contains millions of pixels.
You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a
malfunction and does not affect the performance and reliability of
the product. This phenomenon also occurs in third-party products
and is not subject to exchange or refund.
•• You may find different brightness and color of the panel depending
on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is
not related with the product performance, and it is not malfunction.
•• Displaying a still image for a prolonged period of time may cause
image sticking. Avoid displaying a fixed image on the TV screen for a
long period of time.
Generated sound
•• “Cracking” noise: A cracking noise that occurs when watching or
turning off the TV is generated by plastic thermal contraction due to
temperature and humidity. This noise is common for products where
thermal deformation is required.
•• Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a large
amount of current to operate a product. It varies depending on the
product. This generated sound does not affect the performance and
reliability of the product.
14
Specifications
(Depending on country)
ENGLISH
Broadcasting Specifications
Digital TV
Television system
Programme coverage
Analogue TV
PAL B/B, PAL B/G, PAL D/K, PAL-I
DVB-T/T2
SECAM B/G, SECAM D/K
DVB-C
NTSC-M
VHF, UHF
VHF, UHF, CATV
Maximum number of
storable programmes
2,000
External antenna
impedance
75 Ω
CI Module (W x H x D)
100.0 mm x 55.0 mm x 5.0 mm
Environment condition
Operating Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
15
HDMI/DVI-DTV supported mode
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
31.46
59.94
31.50
31.469
60.00
59.94
720 x 576
31.50
31.250
37.50
60.00
50.00
50.00
1280 x 720
45.00
60.00
44.96
28.125
Resolution
ENGLISH
640 x 480
720 x 480
1920 x 1080
HDMI/DVI-PC supported Mode
•• PC audio is not supported.
•• Use HDMI IN 1 for PC mode (Depending on model)
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
640 x 480
31.469
59.94
800 x 600
37.879
60.31
59.94
50.00
1024 x 768
48.363
60.00
1152 x 864
54.348
60.053
33.75
60.00
1360 x 768
47.712
60.015
33.72
59.94
1280 x 1024
63.981
60.020
56.250
50.00
67.50
60.00
1920 x 10801
67.50
60.00
67.432
59.94
1 Only 43/49LU34*, 43/49LU54*
27.00
24.00
26.973
23.976
Component port connecting
information
33.75
30.00
33.716
29.976
1
Component ports on the TV
RGB-PC supported mode
(Only LU34*)
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
Signal
Component
480i / 576i
O
640 x 480
31.469
59.94
480p / 576p
O
800 x 600
37.879
60.31
720p / 1080i
O
1024 x 768
48.363
60.00
1152 x 864
54.348
60.053
1360 x 768
47.712
60.015
1280 x 10241
63.981
60.020
66.587
59.934
67.50
60.00
1920 x 10801
1 Only 43/49LU34*
16
Video output ports on DVD player
Y
1080p
O
(Only 50 Hz / 60 Hz)
Supported Photo Formats
Extension
Item
.jpeg, .jpg,
.jpe
SOF0: baseline
SOF1: Extend Sequential
SOF2: Progressive
File
type
Item
Info
Bit rate
32 Kbps - 320 Kbps
mp3
Sample freq.
16 kHz - 48 kHz
Support
MPEG-1, MPEG-2, Layer2, Layer3
Minimum: 64 (W) x 64 (H)
Photo Size
Maximum (Normal Type):
15,360 (W) x 8,640 (H)
ACC
Maximum (Progressive Type):
1,920 (W) x 1,440 (H)
.bmp
Photo Size
Available File
Type
Minimum: 64 (W) x 64 (H)
Photo Size
Free Format
Sample freq.
8 kHz - 48 kHz
Support
ADIF, ADTS
Bit rate
Free Format
Sample freq.
8 kHz - 48 kHz
Maximum: 9,600 (W) x 6,400 (H)
Support
MPEG-4
Interlace, Non-Interlace
Bit rate
64 kbps ~ 1.5 Mbps
Sample freq.
8 kHz - 48 kHz
Minimum: 64 (W) x 64 (H)
.png
M4A
Bit rate
WAV
Maximum (Interlace):
1,200 (W) x 800 (H)
Maximum (Non-Interlace):
9,600 (W) x 6,400 (H)
WMA
•• BMP and PNG format files may be slower to display than JPEG.
•• Non-standard photo/image file may not be displayed.
Support
LPCM
Bitdepth
8bit / 16bit / 24bit
Bit rate
128 Kbps ~ 320 Kbps
Sample freq.
8 kHz - 48 kHz
Support
WMA7, WMA8, WMA9 Standard
Bit rate
WMA 10
Pro
Channel /
Sample freq.
ENGLISH
Available File
Type
Resolution
Supported Audio Formats
~ 768Kbps
M0: up to 2 Channel @ 48 kHz
(Except LBR mode),
M1: up to 5.1 Channel @ 48 kHz,
M2: up to 5.1 Channel @ 96 kHz
Support
OGG
WMA 10 Pro
Bit rate
Free Format
Sample freq.
8 kHz - 48 kHz
Support
OGG Vorbis
17
Supported Video Formats
•• Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p)
ENGLISH
Extension
Codec
To obtain the source code under GPL, LGPL, MPL, and other open source
licenses, that is contained in this product, please visit
http://opensource.lge.com.
Video
MPEG-4 Part2, XViD, H.264/AVC,
VC1(WMV3, WVC1), MP43
Audio
WMA Standard, WMA9(Pro), MP3,
AAC, AC3
Video
MPEG-2, MPEG-4 Part2, XViD, H.264/AVC
Audio
HE-AAC, LPCM, ADPCM, MPEG-1 Layer I,
MPEG-1 Layer II, Dolby Digital, MPEG-1
Layer III (MP3)
Video
H.264/AVC, MPEG-2, H.265/HEVC
Audio
MPEG-1 Layer I, MPEG-1 Layer II, MPEG1 Layer III (MP3), Dolby Digital, Dolby
Digital Plus, AAC, HE-AAC
Video
MPEG-1, MPEG-2
Licenses
Audio
Dolby Digital, MPEG-1 Layer I, MPEG-1
Layer II, DVD-LPCM
Video
MPEG-2, MPEG-4 Part2, XVID, H.264/AVC
Supported licenses may differ by model.
.mp4, .m4v
.mov
Audio
AAC, MPEG-1 Layer III (MP3)
Video
MPEG-2, MPEG-4 Part2, XViD, H.264/AVC
Audio
HE-AAC, Dolby Digital, MPEG-1 Layer III
(MP3), LPCM
Video
MJPEG
Audio
LPCM, ADPCM
Video
MPEG-1, MPEG-2
Audio
MPEG-1 Layer I, MPEG-1 Layer II, Dolby
Digital, LPCM
.asf
.wmv
.avi
.ts, .trp, .tp
.mts, .m2ts
.vob
.mkv
motion JPEG
.mpg, .mpeg
.mpe
.dat
.flv
.3gp
18
Open Source Software
Notice Information
Video
MPEG-1, MPEG-2
Audio
MP2
Video
Sorenson H.263, H.264/AVC
Audio
MP3, AAC, HE-AAC
Video
H.264/AVC, MPEG-4 Part2
Audio
AAC, AMR(NB/WB)
In addition to the source code, all referred license terms, warranty
disclaimers and copyright notices are available for download.
LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
as the cost of media, shipping, and handling) upon email request to
opensource@lge.com. This offer is valid for a period of three years after
our last shipment of this product. This offer is valid to anyone in receipt
of this information.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other
countries.
Manufactured under license from Dolby Laboratories. Dolby, Dolby
Vision, Dolby Audio, Dolby Atmos, and the double-D symbol are
trademarks of Dolby Laboratories.
(Depending on model)
Record the model number and serial number of the TV.
Refer to the label on the back cover and quote this
information to your dealer when requiring any service.
MODEL
SERIAL
OWNER’S MANUAL
RS-232C
Please read this manual carefully before operating your set and retain
it for future reference.
www.lg.com
IR CODES
•• This feature is not available for all models.
ENGLISH
Code
(Hexa)
Function
08
F0
39
91
79
0B
10-19
53
1A
(POWER)
/
(INPUT) /
Number Key 0-9
Remote control Button
(Power On/Off)
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
02
Remote control Button
03
Remote control Button
1E
AB
Remote control Button
Remote control Button
(MUTE) /
09
Remote control Button
61
Remote control Button
B1
B0
BA
8E
8F
7C
BD
95
30
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
(HOME)
Remote control Button
/
Remote control Button
Remote control Button
Remote control Button
Remote control Button
/
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
40
/
Remote control Button
41
/
Remote control Button
07
/
Remote control Button
06
/
Remote control Button
(BACK)
Remote control Button
63
E8
/
/
Remote control Button
71
Remote control Button
01
/
/
72
Remote control Button
Remote control Button
45
AA
5B
28
44
Note
7E
/
43
Function
0C
/
T.OPT (T.Option)
(SETTINGS) /
Code
(Hexa)
Remote control Button
00
20
21
2
Note
RS-232C Setup
Phone jack Type
USB IN
EXTERNAL CONTROL DEVICE SETUP
(PC)
(TV)
(Depending on model)
•• You need to purchase the phone-jack to RS-232C cable required for
the(PC)
connection between the PC and the TV, which is specified(TV)
in the
manual.
* For other models, connect to the USB port. 1
3
* The(PC)
connection interface may differ from your TV.
(TV)
RS-232C IN
RS-232C IN (CONTROL & SERVICE)
4
2
1
3
(PC)
(PC)
4
2
RS-232C IN
(TV)
(TV)
(CONTROL & SERVICE)
Type of Connector : D-Sub 9-Pin Male
RS-232C IN
(CONTROL & SERVICE)
1
5
6
9
(*Not provided)
No.
Pin name
2
3.5 V
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
No Connection (5 V available in some models)
8
No Connection
9
No Connection (12 V available in some models)
1
3
ENGLISH
•• Image shown may differ from your TV.
Connect the RS-232C (serial port) input jack to an external control
device (such as a computer or an A/V control system) to control the
product’s functions externally.
Connect the serial port of the control device to the RS-232C jack on the
product back panel.
•• RS-232C connection cables are not supplied with the product.
SERVICE ONLY
(CONTROL & SERVICE)
RS-232C Configurations
Command Reference List
(Depending on model)
7-Wire Configurations
(Standard RS-232C cable)
ENGLISH
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
2
3
5
4
6
7
8
D-Sub 9
Command1 Command2
TV
3
2
5
6
4
8
7
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations
(Not standard)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
2
3
5
4
6
7
8
D-Sub 9
Communication Parameters
•• Baud rate: 9,600 bps (UART)
•• Data length: 8 bits
•• Parity : None
•• Stop bit: 1 bit
•• Communication code: ASCII code
•• Use a crossed (reverse) cable.
TV
3
2
5
6
4
8
7
D-Sub 9
TXD
RXD
GND
DSR
DTR
RTS
CTS
Data
(Hexadecimal)
1 Power
k
a
00 to 01
2 Aspect Ratio
k
c
(See p. 5)
3 Screen Mute
k
d
(See p. 6)
4 Volume Mute
k
e
00 to 01
5 Volume Control
k
f
00 to 64
6 Contrast
k
g
00 to 64
7 Brightness
k
h
00 to 64
8 Colour
k
i
00 to 64
9 Tint
k
j
00 to 64
10 Sharpness
k
k
00 to 32
11 OSD Select
k
l
00 to 01
12 Remote
Control Lock
Mode
k
m
00 to 01
13 Balance
k
t
00 to 64
14 Colour
Temperature
x
u
00 to 64
15 Energy Saving
j
q
(See p. 8)
16 Auto
Configuration
j
u
01
17 Equalizer
j
v
(See p. 8)
18 Tune Command
m
a
(See p. 8)
19 Programme
Skip/Add
m
b
00 to 01
20 Key
m
c
(See p. 9)
21 Control
Backlight
m
g
00 to 64
22 Input select
x
b
(See p. 9)
•• During USB operations such as DivX or EMF, all commands except
Power(ka) and Key(mc) are not executed and treated as NG.
4
Transmission / Receiving Protocol
(Depending on Model)
Transmission
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format
when receiving normal data. At this time, if the data is data read
mode, it indicates present status data. If the data is data write
mode, it returns the data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format
when receiving abnormal data from non-viable functions or
communication errors.
Data 00 : Illegal Code
►To
► control Power On/Off of the set.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
ENGLISH
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command1] : First command to control the TV. (j, k, m or x)
[Command2] : Second command to control the TV.
[Set ID] : You can adjust the set ID to choose desired monitor ID
number in option menu. Adjustment range is 1 to 99. When selecting
Set ID ‘0’, every connected set is controlled. Set ID is indicated as
decimal (1 to 99) on menu and as Hexa decimal (0 x 0 to 0 x 63) on
transmission/receiving protocol.
[Data] : To transmit command data. Transmit ‘FF’ data to read status
of command.
[Cr] : Carriage Return
ASCII code ‘0 x 0D’
[ ] : ASCII code ‘space (0 x 20)’
1 Power (Command: k a)
Data 00 : Off
Data 01 : On
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
►To
► Show TV is Power On/Off.
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0 x FF’ data based on this
format, Acknowledgement data feed back presents status about
each function.
* OK Ack., Error Ack. and other message may display on the screen
when TV is power On.
2 Aspect Ratio (Command: k c) (Main Picture Size)
(Depending on model)
►To
► adjust the screen format. (Main picture format) You can also
adjust the screen format using the picture settings.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 01 : 4:3 (Normal screen - Just Scan Off)
Data 02 : 16:9 (Wide screen - Just Scan Off)
Data 06 : Original (Just Scan Off)
Data 09 : Just Scan
* Please make sure that the model doesn't support both Vertical Zoom
and All-Direction Zoom mode.
Ack
[c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p 24 Hz
/ 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i, 1080p 50 Hz / 60
Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital, Analogue, AV.
5
3 Screen Mute (Command: k d)
6 Contrast (Command: k g)
►To
► select screen mute on/off.
►To
► adjust screen contrast.
You can also adjust contrast in the picture settings.
Transmission
ENGLISH
[k][d][ ][Set ID][ ][Data][Cr]
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on) / Video mute off
Data 01 : Screen mute on (Picture off)
Data 10 : Video mute on
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
Ack
Ack
[d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen Display
(OSD). But, in case of Screen mute on, TV will not display OSD.
4 Volume Mute (Command: k e)
►To
► control volume mute on/off.
You can also adjust mute using the mute button on remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
Data 01 : Volume mute off (Volume on)
[g][ ][Set ID][ ][OK/NG][Data][x]
7 Brightness (Command: k h)
►To
► adjust screen brightness.
You can also adjust brightness in the picture settings.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
Ack
[h][ ][Set ID][ ][OK/NG][Data][x]
Ack
[e][ ][Set ID][ ][OK/NG][Data][x]
5 Volume Control (Command: k f)
8 Colour (Command: k i)
►To
► adjust the screen colour.
You can also adjust colour in the picture settings.
►To
► adjust volume.
You can also adjust volume with the volume buttons on remote
control.
Transmission
Transmission
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to "Real data mapping".
Ack
[f][ ][Set ID][ ][OK/NG][Data][x]
6
[k][i][ ][Set ID][ ][Data][Cr]
Ack
[i][ ][Set ID][ ][OK/NG][Data][x]
9 Tint (Command: k j)
12 Remote Control Lock Mode (Command: k m)
►To
► adjust the screen tint.
You can also adjust tint in the picture settings.
►To
► lock the front panel controls on the monitor and remote control.
Transmission
Data Red : 00 to Green : 64
* Refer to "Real data mapping".
Ack
[j][ ][Set ID][ ][OK/NG][Data][x]
10 Sharpness (Command: k k)
►To
► adjust the screen sharpness.
You can also adjust sharpness in the picture settings.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 32
* Refer to "Real data mapping".
Ack
[k][ ][Set ID][ ][OK/NG][Data][x]
11 OSD Select (Command: k l)
►To
► select OSD (On Screen Display) on/off when controlling remotely.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 00 : Off
Data 01 : On
Ack
[l][ ][Set ID][ ][OK/NG][Data][x]
[k][m][ ][Set ID][ ][Data][Cr]
ENGLISH
[k][j][ ][Set ID][ ][Data][Cr]
Transmission
Data 00 : Off
Data 01 : On
Ack
[m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this mode. When main
power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by power
on key of IR & Local Key.
13 Balance (Command: k t)
►To
► adjust balance.
You can also adjust balance in the audio settings.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data L : 00 to R : 64
* Refer to "Real data mapping".
Ack
[t][ ][Set ID][ ][OK/NG][Data][x]
14 Colour Temperature (Command: x u)
►To
► adjust Colour Temperature. You can also adjust Colour
Temperature in the picture settings.
Transmission
[x][u][ ][Set ID][ ][Data][Cr]
Data Warm: 00 to Cool:64
* Refer to "Real data mapping".
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
7
15 Energy Saving (Command: j q)
17 Equalizer (Command : j v)
►To
► reduce the power consumption of the TV. You can also adjust
Energy Saving in picture settings.
►To
► adjust equalizer.
Transmission
Transmission
ENGLISH
[j][v][ ][Set ID][ ][Data][Cr]
[j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function
7 6 5 4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MSB
Level
Low
Power
Low
Power
Low
Power
Low
Power
Low
Power
Low
Power
Description
3
2
1
0
0
0
0
0
Off
0
0
0
1
Minimum
0
0
1
0
Medium
0
0
1
1
Maximum
0
1
0
1
Screen Off
0
1
0
0
Auto
Ack
[q][ ][Set ID][ ][OK/NG][Data][x]
16 Auto Configuration (Command: j u) (Only RGB support model)
►To
► adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
[j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
0
0
0
0
7 6 5
0
0
Frequency
4 3 2 1 0
Step
0 0 0
1st Band
0 0 0 0 0
0 (decimal)
0 0 1
2nd Band
0 0 0 0 1
1 (decimal)
0 1 0
3rd Band
... ... ... ... ...
...
0 1 1
4th Band
1 0 0 1 1
19 (decimal)
1 0 0
5th Band
1 0 1 0 0
20 (decimal)
Ack
[v][ ][Set ID][ ][OK/NG][Data][x]
18 Tune Command (Command: m a)
►Select
►
channel to following physical number.
Transmission
[m][a][ ][Set ID][ ][Data 00][ ][Data 01][ ][Data 02][Cr]
Data 00 : High channel data
Data 01 : Low channel data
ex. No. 47 00 2F (2FH)
No. 394 01 8A (18AH),
DTV No. 0 Don’t care
Data 02 : [Antenna]
0 x 00 : Analogue Main
0 x 10 : DTV Main
0 x 20 : Radio
[Cable]
0 x 80 : Analogue Main
0 x 90 : DTV Main
0 x A0 : Radio
[Satellite] (Depending on model)
0 x 40 : DTV Main
0 x 50 : Radio Main
Channel data range
Min : 00 Max : 270F (0 to 9999)
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
8
0
Data
Frequency
►‘Auto’
►
is available in TV that supports ‘Intelligent Sensor’.
Transmission
LSB
0
19 Programme Skip/Add (Command: m b)
22 Input select (Command: x b) (Main Picture Input)
►To
► set skip status for the current Programme.
►To
► select input source for main picture.
Transmission
Transmission
Data 00 : Skip
Data 01 : Add
Ack
[x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
[b][ ][Set ID][ ][OK/NG][Data][x]
0
LSB
0
0
0
0
External Input
20 Key (Command: m c)
0
0
0
Input Number
►To
► send IR remote key code.
External Input
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data
0
0
0
0
DTV
Data IR CODES
0
0
0
1
Analogue
Ack
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
[c][ ][Set ID][ ][OK/NG][Data][x]
21 Control Backlight (Command: m g)
►To
► control the backlight.
Transmission
[m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack
Input Number
[g][ ][Set ID][ ][OK/NG][Data][x]
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
9
ENGLISH
[m][b][ ][Set ID][ ][Data][Cr]
* Real data mapping
00 :
Step 0
ENGLISH
10
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E :
Step 110
73 :
74 :
Step 115
Step 116
CF :
Step 199
FE :
FF :
Step 254
Step 255
Record the model number and serial number of the TV.
Refer to the label on the back cover and quote this
information to your dealer when requiring any service.
MODEL
SERIAL
Download PDF