LG | 32LX530S | LG 32LX530S Owner’s Manual

OWNER’S MANUAL
Safety and Reference
LED TV*
* LG LED TVs are LCD TVs with LED backlighting.
Please read this manual carefully before operating
your TV and retain it for future reference.
32LX330C
42LX330C
49LX341C
55LX341C
60LX341C
65LX341C
42LX530S
*MFL68925803*
49LX540S
55LX540S
60LX540S
65LX540S
43LX310C
49LX310C
www.lg.com
P/NO : MFL68925803 (1504-REV00)
Important Safety Instructions
Always comply with the following precautions
to avoid dangerous situations and ensure peak
performance of your product.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
••Do not use this apparatus near water.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ENGLISH
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol within an equilateral triangle is
intended to alert the user to the presence of
uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important operating
and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
WARNING
If you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
••Clean only with dry cloth.
••Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
••Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
••Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
CAUTION
If you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
The note helps you understand and use the
product safely. Please read the note carefully
before using the product.
••Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
••Only use attachments/accessories specified by
the manufacturer.
2
••Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
••Unplug this apparatus during lightning storms
or when unused for long periods of time.
••Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
••Warning - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product near
flammable objects such as gasoline or candles,
or expose the TV to direct air conditioning.
••Do not expose to dripping or splashing and
do not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.,
on shelves above the unit).
ENGLISH
••Do not press strongly upon the panel with a
hand or a sharp object such as a nail, pencil, or
pen, or make a scratch on it.
appliance, and have the cord replaced with
an exact replacement part by an authorized
service. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. Do
not move the TV with the power cord plugged
in. Do not use a damaged or loose power cord.
Be sure do grasp the plug when unplugging the
power cord. Do not pull on the power cord to
unplug the TV.
••Do not stick metal objects or any other
conductive material into the power cord. Do
not touch the end of the power cord while it is
plugged in.
••Keep the packing anti-moisture material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if swallowed.
If swallowed, induce vomiting and go to the
nearest hospital. Additionally, vinyl packing can
cause suffocation. Keep it out of the reach of
children.
••CAUTION concerning the Power Cord
(Can differ by country):
Check the specification page of this owner’s
manual to be certain. Do not connect too many
appliances to the same AC power outlet as this
could result in fire or electric shock. Do not
overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked
wire insulation are dangerous. Any of these
conditions could result in electric shock or fire.
Periodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
3
••Grounding
(Except for devices which are not grounded.)
Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e., a TV
with a three-prong grounded AC plug must
be connected to a three-prong grounded AC
outlet). If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker. Do not try to ground the unit by
connecting it to telephone wires, lightning rods,
or gas pipes.
Circuit
Breaker
Power
Supply
ENGLISH
••As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if the unit is turned off.
••Do not attempt to modify this product in any
way without written authorization from LG
Electronics. Unauthorized modification could
void the user’s authority to operate this product.
••Outdoor Antenna Grounding
(Can differ by country):
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can come in contact with
such power lines or circuits as death or serious
injury can occur. Be sure the antenna system is
grounded to provide some protection against
voltage surges and built-up static charges.
Section 810 of the National Electrical Code (NEC)
in the U.S.A. provides information with respect
to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Ground Clamp
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamp
NEC: National Electrical Code
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
••Cleaning
When cleaning, unplug the power cord and wipe
gently with a soft cloth to prevent scratching. Do
not spray water or other liquids directly on the
TV as electric shock may occur. Do not clean with
chemicals such as alcohol, thinners, or benzene.
4
••Moving
Make sure the product is turned off, unplugged,
and all cables have been removed. It may take 2
or more people to carry larger TVs. Do not press
or put stress on the front panel of the TV.
••Ventilation
Install your TV where there is proper ventilation.
Do not install in a confined space such as a
bookcase. Do not cover the product with cloth or
other materials while plugged. Do not install in
excessively dusty places.
••If you smell smoke or other odors coming from
the TV, unplug the power cord and contact an
authorized service center.
••Keep the product away from direct sunlight.
••Never touch this apparatus or antenna during a
lightning storm.
••When mounting a TV on the wall, make sure not
to install the TV by hanging the power and signal
cables on the back of the TV.
••Do not allow an impact shock, any objects to fall
into the product, and do not drop anything onto
the screen.
••DISCONNECTING THE DEVICE FROM THE
MAIN POWER
The power plug is the disconnecting device.
In case of an emergency, the power plug must
remain readily accessible.
••Batteries
Store the accessories (battery, etc.) in a safe
location out of the reach of children.
••This apparatus uses batteries. In your community
there might be regulations that require you
to dispose of these batteries properly due to
environmental considerations. Please contact
your local authorities for disposal or recycling
information.
••Do not dispose of batteries in a fire.
••Do not short circuit, disassemble, or allow the
batteries to overheat.
••Do not use high voltage electrical equipment
near the TV, (e.g., a bug zapper.)
This may result in product malfunction.
••Dot Defect
The panel is a high technology product with
resolution of two million to six million pixels.
In a very few cases, you could see fine dots on
the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the
performance and reliability of the TV.
••Generated Sound
Cracking noise A cracking noise that occurs
when watching or turning off the TV is
generated by plastic thermal contraction due to
temperature and humidity. This noise is common
for products where thermal deformation is
required.
Electrical circuit humming/panel buzzing
A low level noise is generated from a highspeed switching circuit, which supplies a large
Preventing Image Burn or Burn-in on Your
TV Screen
••If a fixed image displays on the TV screen for
a long period of time, it will be imprinted and
become a permanent disfigurement on the
screen. This is image burn or burn-in and not
covered by the warranty.
••If the aspect ratio of the TV is set to 4:3 for a long
period of time, image burn may occur on the
letterboxed area of the screen.
••Avoid displaying a fixed image on the TV screen
for a long period of time to prevent image burn.
ENGLISH
amount of current to operate a product. It varies
depending upon the product. This generated
sound does not affect the performance and
reliability of the product.
••Take care not to touch the ventilation openings.
When watching the TV for a long period, the
ventilation openings may become hot. This does
not affect the performance of the product or
cause defects in the product.
••Do not install this product on a wall if it could be
exposed to oil or oil mist. This may damage the
product and cause it to fall.
••If the TV feels cold to the touch, there may
be a small flicker when it is turned on. This is
normal; there is nothing wrong with TV. Some
minute dot defects may be visible on the screen,
appearing as tiny red, green, or blue spots.
However, they have no adverse effect on the TV’s
performance. Avoid touching the LCD screen or
holding your finger(s) against it for long periods
of time. Doing so may produce some temporary
distortion effects on the screen.
••If water or another substance enters the product
(like a AC adapter, power cord, TV), disconnect
the power cord and contact the service centre
immediately.
Otherwise, this may result in fire or electric
shock.
••Only use an authorized AC adapter and power
cord approved by LG Electronics. Otherwise, this
may result in fire, electric shock, malfunction or
product deformation.
••Never Disassemble the AC adapter or power
cord.
This may result in fire or electric shock.
5
ENGLISH
FCC Notice
FCC RF Radiation Exposure Statement
(For USA)
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and the receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference and (2) this device must accept any
interference received, including interference that
may cause undesired operation of the device. Any
changes or modifications in construction of this
device which are not expressly approved by the
party responsible for compliance could void the
user’s authority to operate the equipment.
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be
colocated or operating in conjunction with any
other antenna or transmitter. This equipment
should be installed and operated with minimum
distance 20 cm (7.8 inches) between the radiator
and your body. Users must follow the specific
operating instructions for satisfying RF exposure
compliance.
FCC Radio Frequency Interference
Requirements (for UNII devices)
High power radars are allocated as primary users
of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands.
These radar stations can cause interference with
and/or damage this device. This device cannot be
co-located with any other transmitter.
6
Industry Canada Statement
(For Canada)
[For having wireless function (WLAN, Bluetooth,...)]
This device complies with RSS-210 of the Industry
Canada Rules. Operation is subject to the following
two conditions:
1. this device may not cause interference and
2. this device must accept any interference,
including interference that may cause undesired
operation of the device.
IC Radiation Exposure Statement
(For Canada)
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with minimum distance 20 cm (7.8
inches) between the radiator & your body.
NOTE : THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD
VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
WARNING
(For Canada)
[For product having the wireless function using 5
GHz frequency bands]
••The device for operation in the band 5150–5250
MHz is only for indoor use to reduce the
potential for harmful interference to co-channel
mobile satellite systems;
••The maximum antenna gain permitted for
devices in the bands 5250–5350 MHz and
5470–5725 MHz shall comply with the EIRP limit;
and
••The maximum antenna gain permitted for
devices in the band 5725–5825 MHz shall
comply with the EIRP limits specified for pointto-point and non point-to-point operation as
appropriate.
••High-power radars are allocated as primary users
(i.e. priority users) of the bands 5250–5350 MHz
and 5650–5850 MHz and that these radars could
cause interference and/or damage to LE-LAN
devices.
Note to Cable/TV Installer
NOTE
••Image shown may differ from your TV.
••Your TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
••The available menus and options may differ from
the input source or product model that you are
using.
••New features may be added to this TV in the
future.
••The items supplied with your product may vary
depending upon the model.
••Product specifications or contents of this manual
may be changed without prior notice due to
upgrade of product functions.
••For an optimal connection, HDMI cables and USB
devices should have bezels less than 10 mm (0.39
inches) thick and 18 mm (0.7 inches) width.
••Use an extension cable that supports USB 2.0 if
the USB cable or USB flash drive does not fit into
your TV’s USB port.
••Use a certified cable with the HDMI logo
attached. If you do not use a certified HDMI
cable, the screen may not display or a
connection error may occur.
••Recommended HDMI cable types (3 m or less)
-- High-Speed HDMI®/™ cable
-- High-Speed HDMI®/™ cable with Ethernet
B
B
A
A
*A 10 mm (0.39 inches)
*B 18 mm (0.7 inches)
CAUTION
••Do not use any unapproved items to ensure the
safety and lifespan of the product.
••Any damages or injuries by using unapproved
items are not covered by the warranty.
••Some models appear to have a thin film on the
screen. It is actually part of the screen; do not
remove it.
••When attaching the stand to the TV set, place
the screen facing down on a cushioned table or
flat surface to protect the screen from scratches.
••Make sure that the screws are fastened tightly.
(If they are not fastened securely enough, the TV
may tilt forward after being installed.)
••Do not fasten the screws with excessive force;
otherwise, they may be worn out and become
loose.
7
ENGLISH
(For USA and Canada)
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the
National Electric Code (U.S.A.). The code provides
guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected
to the grounding system of the building, as close
to the point of the cable entry as practical.
Preparing
Warning when using USB storage devices
••USB storage devices with a built-in auto
recognition program or its own driver may not
work.
••Some USB storage devices may not work or may
work improperly.
••Use only those USB storage devices formatted
with FAT32 or NTFS File System provided by
Windows.
••For external USB HDD, use devices with less than
5V-rated voltages and 500 mA-rated current.
••It is recommended to use USB flash drive with 32
GB or less and USB HDD with 2 TB or less.
••If a USB HDD with power-saving function does
not work properly, turn the power off and on.
For more information, refer to the user manual
of USB HDD.
••Data in the USB storage device can be damaged
so back up important files in other devices. Data
maintenance is the user’s responsibility. The
manufacturer is not responsible for data loss.
Maintenance
ENGLISH
Cleaning Your TV
Clean your TV regularly to keep it at peak
performance and to extend the product’s lifespan.
CAUTION
••Before cleaning, turn the power off and
disconnect the power cord and all other cables.
••When the TV is left unattended or unused for a
long time, disconnect the power cord from the
wall outlet to prevent possible damage from
lightning or power surges.
CAUTION
••Do not push, rub, or hit the surface with your
fingernail or a sharp object, as this may result in
scratches on the screen and image distortions.
••Do not use any chemicals, such as waxes,
benzene, alcohol, thinners, insecticides, air
fresheners, or lubricants, as these may damage
the screen’s finish and cause discoloration.
••Do not spray liquid onto the surface. If water
enters the TV, it may result in fire, electric shock,
or malfunction.
Power Cord
Remove the accumulated dust or dirt on the power
cord regularly.
Lifting and Moving the TV
When moving or lifting the TV, read the following
to prevent the TV from being scratched or
damaged and for safe transportation regardless of
its type and size.
••It is recommended to move the TV in the box or
packing material that the TV originally came in.
••Before moving or lifting the TV, disconnect the
power cord and all cables.
••When holding the TV, the screen
should face away from you to
avoid damage.
••Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grille area.
Screen, Frame, Cabinet, and Stand
To remove dust or light dirt, wipe the surface with
a dry, clean, and soft cloth.
To remove major dirt, wipe the surface with a soft
cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
••Use at least two people to move
a large TV.
••When transporting the TV by
hand, hold the TV as shown in the
following illustration.
••When transporting the TV, do not expose the TV
to jolts or excessive vibration.
••When transporting the TV, keep the TV upright;
never turn the TV on its side or tilt towards the
left or right.
8
CAUTION
••Avoid touching the screen at all times, as this
may result in damage to the screen.
••Do not place the product on the floor with its
front facing down without padding. Failure to do
so may result in damage to the screen.
••Do not move the TV by holding the cable
holders, as the cable holders may break, and
injuries and damage to the TV may occur.
(Depending upon model)
Adjusting the Menu
When the TV is turned on, press the joystick button
one time. You can adjust the menu items moving
the joystick button up, down, left, or right.
Turns the power off.
Accesses the main menu.
Clears on-screen displays and returns to TV viewing
Changes the input source.
Using the Joystick Button
Mounting on a Table
(Image shown may differ from your TV.)
You can operate the TV by pressing the button or
moving the joystick left, right, up, or down.
(Image shown may differ from your TV.)
1 Lift and tilt the TV into its upright position on a
table.
- Leave a 10 cm (4 inches) (minimum) space
from the wall for proper ventilation.
Joystick Button
10 cm
(4 inches)
Basic Functions
Power On
Power Off
Volume
Control
Channels
Control
When the TV is turned off, place your
finger on the joystick button, press it
once, and release it.
When the TV is turned on, place your
finger on the joystick button, press it
once for a few seconds, and release it.
(However, if the menu button is on the
screen, pressing and holding the joystick
button will let you exit the menu.)
ENGLISH
10 cm
10 cm
m
10 c
2 Connect the power cord to a wall outlet.
If you place your finger over the joystick
button and move it left or right, you can
adjust the volume level.
If you place your finger over the joystick
button and move it up or down, you can
scroll through the saved channels.
NOTE
••Move the joystick up, down, left, or right. Be
careful not to press the joystick button. If you
press the joystick button first, you may not be
able to adjust the volume level and/or scroll
through saved channels.
9
CAUTION
••Do not place the TV near or on sources of heat,
as this may result in fire or other damage.
Using the Kensington Security
System (optional)
(Depending upon model)
(Image shown may differ from your TV.)
The Kensington security system connector is
located at the rear of the TV. For more information
of installation and using, refer to the manual
provided with the Kensington security system
or visit http://www.kensington.com. Connect the
Kensington security system cable between the TV
and a table.
NOTE
ENGLISH
••The Kensington security system is optional. You
can obtain additional accessories from your local
dealer.
Securing the TV to a Wall
(optional)
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope or cable. Make sure to keep
the rope parallel to the flat surface.
CAUTION
••Make sure that children do not climb on or hang
on the TV.
NOTE
••Use a platform or cabinet that is strong and large
enough to support the TV securely.
••Brackets, bolts, and ropes are optional. You can
obtain additional accessories from your local
dealer.
Mounting on a Wall
An optional wall mount can be used with your
LG Television. Consult with your local dealer for
a wall mount that supports the VESA standard
used by your TV model. Carefully attach the wall
mount bracket at the rear of the TV. Install the wall
mount bracket on a solid wall perpendicular to the
floor. If you are attaching the TV to other building
materials, please contact qualified personnel to
install the wall mount. Detailed instructions will
be included with the wall mount. We recommend
that you use an LG brand wall mount. When you do
not use LG’s wall mount bracket, use a wall mount
bracket where the device is adequately secured to
the wall with enough space to allow connectivity
to external devices.
(Depending upon model)
(Image shown may differ from your TV.)
10 cm
(4 inches)
10 cm
10 cm
10 cm
Make sure to use screws and wall mounts that
meet the VESA standard. Standard dimensions for
the wall mount kits are described in the following
table.
1 Insert and tighten the eye-bolts or TV brackets
and bolts on the back of the TV.
- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall. Match the location of the wall bracket and
the eye-bolts on the rear of the TV.
10
32LX330C
43LX310C
VESA (A x B)
200 x 200
Standard screw
M6
Number of screws
4
Wall mount bracket LSW240B
(optional)
MSW240
Model
49LX341C
55LX341C
Model
49LX540S
55LX540S
49LX310C
VESA (A x B)
300 x 300
Standard screw
M6
Number of screws
4
Wall mount bracket LSW350B
(optional)
MSW240
42LX330C
42LX530S
400 x 400
M6
4
LSW440B
MSW240
••When using the wall mounting bracket, apply
the adhesive protective label to cover the
unused stand opening(s). This will prevent the
accumulation of dust and dirt. (Use only when
provided with your particular model.)
Provided Item
60LX341C
65LX341C
60LX540S
65LX540S
300 x 300
M6
4
LSW350B
A
B
Adhesive Protective Label
••When attaching a wall mounting bracket to the
TV, insert the wall mount inner spacers into the
TV wall mount holes to adjust the vertical angle
of the TV. (Use only when provided with your
particular model.)
Provided Item
CAUTION
ENGLISH
••Disconnect the power before moving or
installing the TV. Otherwise electric shock may
occur.
••Remove the stand before installing the TV on a
wall mount by performing the stand attachment
in reverse.
••If you install the TV on a ceiling or slanted wall,
it may fall and result in severe injury. Use an
authorized LG wall mount and contact the local
dealer or qualified personnel. When using a
third-party wall mount, it is not covered by the
warranty.
••Do not overtighten the screws as this may cause
damage to the TV and void your warranty.
••Use the screws and wall mounts that meet the
VESA standard. Any damages or injuries by
misuse or using an improper accessory are not
covered by the warranty.
Wall Mount Spacer
Connections (Notifications)
You can connect various external devices to the TV.
Supported external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices. For
more information on external device’s connection,
refer to the manual provided with each device.
NOTE
••Use the screws that are listed in the VESA
standard screw specifications.
••The wall mount kit includes an installation
manual and necessary parts.
••The wall mount bracket is optional. You can
obtain additional accessories from your local
dealer.
••The length of screws may differ depending upon
the wall mount. Make sure to use the proper
length.
••For more information, refer to the manual
supplied with the wall mount.
11
NOTE
••If you record a TV program on a DVD recorder or
VCR, make sure to connect the TV signal input
cable to the TV through a DVD recorder or VCR.
For more information about recording, refer to
the manual provided with the connected device.
••The external device connections shown may
differ slightly from illustrations in this manual.
••Connect external devices to the TV regardless
about the order of the TV port.
••If you connect a gaming device to the TV, use the
cable supplied with the gaming device.
••Refer to the external equipment’s manual for
operating instructions.
Connecting to an Antenna or
Cable
Connect an antenna, cable, or cable box to watch
TV while referring to the following. The illustrations
may differ from the actual items and an RF cable is
optional.
Remote Control
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly. To
install batteries, open the battery cover, replace
batteries (1.5 V AAA) matching the and ends
to the label inside the compartment, and close
the battery cover. Failure to match the correct
polarities of the battery may cause the battery
to burst or leak, resulting in fire, personal injury,
or ambient pollution. To remove the batteries,
perform the installation actions in reverse. This
remote uses infrared light. When in use, it should
be pointed in the direction of the TV’s remote
sensor.
CAUTION
••Do not mix old and new batteries, as this may
damage the remote control.
ENGLISH
CAUTION
A
••Make sure not to bend the copper wire of the RF
cable.
Copper wire
FLASHBK
••Complete all connections between devices, and
then connect the power cord to the power outlet
to prevent damage to your TV.
B
AUDIO
NOTE
••Use a signal splitter to use 2 TVs or more.
••DTV Audio Supported Codec: MPEG,
Dolby Digital.
Other Connections
A
(POWER) Turns the TV on or off.
Connect your TV to external devices. For the best
picture and audio quality, connect the external
device and the TV with the HDMI cable.
Returns to the last TV channel.
Activates or deactivates the subtitles.
Selects an AV mode.
Resizes an image.
NOTE
Changes the input source.
••Use only with the 3-pole 3.5 mm Stereo Jack.
B
Number button Enters numbers.
(DASH) Inserts a dash between numbers such as 2-1
and 2-2.
12
Accesses the saved channel list.
Alternates between the two last channels
selected (pressing repeatedly).
Adjusts the volume level.
Accesses your favorite channel list.
Digital signal : Changes the audio language.
Analog signal : Changes
the MTS sound.
FLASHBK
Mutes all sounds.
Scrolls through the saved channels.
AUDIO
Moves to the previous or next screen.
C
D
To select Picture Mode
To Use Energy Saving Feature
C
Changes the image mode.
Shows information on the current program.
Changes the sound mode.
Accesses the main menu.
Accesses the quick menu.
SETTINGS
PICTURE
Energy Saving
Reduces power consumption by adjusting peak
screen brightness.
••Off Turns off the Energy Saving.
••Minimum / Medium / Maximum Applies the
pre-set Energy Saving.
••Screen Off Screen is turned off and only sound
is played. Press any button on the remote control
to turn the screen back on.
Navigation button (up/down/left/right) Scrolls through
menus or options.
Selects menus or options and confirms your input.
Returns to the previous screen.
Clears all on-screen displays and returns to TV
viewing.
D
Not functional.
Sets the length of time until the TV to turns off.
Control buttons (
) Controls the MY MEDIA
menus and the SIMPLINK compatible devices (USB,
SIMPLINK).
Color buttons (
functions in some menus.
)These access special
13
ENGLISH
SETTINGS
PICTURE
Picture Mode
Select the picture mode optimized for the viewing
environment or the program.
••Vivid Heightens contrast, brightness, and
sharpness to display vivid images.
••Standard Displays images in standard levels of
contrast, brightness and sharpness.
••APS APS (Auto power saving) mode reduces
power consumption by dimming control.
••Cinema / Game Displays the optimum picture
for movie or game.
••Expert Menu for adjusting picture quality that
allows experts and amateurs to enjoy the best TV
viewing. This menu for adjustment is provided
for ISF-certified picture tuning professionals.
(ISF logo can be used only on ISF-certified TVs.)
ISFccc: Imaging Science Foundation Certified
Calibration Control
••Depending upon the input signal, the available
range of picture modes may differ.
••Expert mode is for picture tuning professionals
to control and fine-tune using a specific image.
For normal images, the effects may not be
drastic.
To set Motion Eye Care
[Depending upon model]
SETTINGS
PICTURE
Picture Mode
Picture Option
••Motion Eye Care Automatically adjusts
brightness and reduces image blur based on
image data to reduce eyestrain.
Specifications
Product specifications may be changed without
prior notice due to upgrade of product functions.
Television System ATSC, NTSC-M, 64 & 256 QAM
Program Coverage
HF 2-13, UHF 14-69, DTV 2-69, CATV 1-135,
V
CADTV 1-135
External Antenna Impedance
ENGLISH
75 Ω
RGB(PC), HDMI (PC) Supported Mode
(Use HDMI IN 1 for PC mode)
Resolution
640 x 350
720 x 400
640 x 480
800 x 600
1024 x 768
1360 x 768
1152 x 864
1280 x 1024
(For FHD)
1920 x 1080
(For FHD)
Horizontal
Frequency (kHz)
31.46
31.46
31.46
37.87
48.36
47.71
54.34
Vertical
Frequency (Hz)
70.09
70.08
59.94
60.31
60.00
60.01
60.05
63.98
60.02
67.50
60.00
* FHD
42LX330C, 49LX341C, 55LX341C, 60LX341C,
65LX341C, 42LX530S, 49LX540S, 55LX540S,
60LX540S, 65LX540S, 43LX310C, 49LX310C
HDMI (DTV) Supported Mode
Resolution
720 x 480p
Environment Condition
1280 x 720p
••Operating Temperature
0 °C to 40 °C (32 °F to 104 °F)
••Operating Humidity
Less than 80 %
••Storage Temperature
-20 °C to 60 °C (-4 °F to 140 °F)
••Storage Humidity
Less than 85 %
1920 x 1080i
1920 x 1080p
Horizontal
Frequency (kHz)
31.47
31.50
44.96
45.00
33.72
33.75
26.97
27.00
33.71
33.75
67.43
67.50
Vertical
Frequency (Hz)
59.94
60.00
59.94
60.00
59.94
60.00
23.97
24.00
29.97
30.00
59.94
60.00
Component Port Connecting Information
14
Component ports on the TV
Y
PB
PR
Video output ports on DVD player
Y
Y
Y
Y
PB
B-Y
Cb
Pb
PR
R-Y
Cr
Pr
Component Supported Mode
Resolution
720 x 480i
720 x 480p
1280 x 720p
1920 x 1080i
1920 x 1080p
Horizontal
Frequency (kHz)
15.73
15.73
31.47
31.50
44.96
45.00
33.72
33.75
26.97
27.00
33.71
33.75
67.432
67.50
Vertical
Frequency (Hz)
59.94
60.00
59.94
60.00
59.94
60.00
59.94
60.00
23.976
24.00
29.97
30.00
59.94
60.00
Supported Video Formats
Supported Audio Formats
••File type : mp3
[Bit rate] 32 Kbps - 320 Kbps
[Sample freq.] 16 kHz - 48 kHz
[Support] MPEG1, MPEG2, Layer2, Layer3
••File Type : AAC
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] ADIF, ADTS
••File Type : M4A
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] MPEG-4
••File Type : WMA
[Bit rate] 128 Kbps ~ 320 Kbps
[Sample freq.] 8 kHz ~ 48 kHz
[Support] WMA7, WMA8, WMA9 Standard
••File Type : WMA 10 Pro
[Bit rate] ~ 768 Kbps
[Channel / Sample freq.]
M0 : up to 2 Channel @ 48 kHz
(Except LBR mode),
M1 : up to 5.1 Channel @ 48 kHz,
M2 : up to 5.1 Channel @ 96 kHz
[Support] WMA 10 Pro
••File Type : OGG
[Bit rate] Free Format
[Sample freq.] ~ 48 kHz
[Support] OGG Vorvis
ENGLISH
••Maximum: 1920 x 1080 @ 30p (only Motion JPEG
640 x 480 @ 30p)
••.asf, .wmv
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,
DivX5, DivX6, XViD, H.264/AVC, VC1(WMV3,
WVC1), MP43
[Audio] WMA Standard, WMA9(Pro), MP3, AAC,
AC3, MP3, 3D WMV Single Stream.
••.divx, .avi
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,
DivX5, DivX6, XViD, H.264/AVC
[Audio] HE-AAC, LPCM, ADPCM, MPEG- 1 Layer I,
MPEG-1 Layer II, Dolby Digital, MPEG-1 Layer III
(MP3), *DTS
••.ts, .trp, .tp, .mts, .m2ts
[Video] H.264/AVC, MPEG-2, AVS, VC1
[Audio] MPEG-1 Layer I, MPEG-1 Layer II, MPEG-1
Layer III (MP3), Dolby Digital, Dolby Digital Plus,
AAC, HE-AAC, *DTS
••.vob
[Video] MPEG-1, MPEG-2
[Audio] Dolby Digital, MPEG-1 Layer I, MPEG- 1
Layer II, DVD-LPCM
••.mp4, .m4v, .mov
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,
DivX5, DivX6, XVID, H.264/AVC
[Audio] AAC, MPEG-1 Layer III (MP3), *DTS
••.mkv
[Video] MPEG-2, MPEG-4 Part2, DivX3.11, DivX4,
DivX5, DivX6, XVID, H.264/AVC
[Audio] HE-AAC, Dolby Digital, MPEG-1 Layer III
(MP3), *DTS, LPCM
••motion JPEG
[Video] MJPEG
[Audio] LPCM, ADPCM
••.mpg, .mpeg, .mpe
[Video] MPEG-1, MPEG-2
[Audio] MPEG-1 Layer I, MPEG-1 Layer II, Dolby
Digital, LPCM
••.dat
[Video] MPEG-1, MPEG-2
[Audio] MP2
••.flv
[Video] Sorenson H.263, H.264/AVC
[Audio] MP3, AAC, HE-AAC
••*rm, *rmvb
[Video] RV30, RV40
[Audio] Dolby Digital, AAC, HE-AAC, RA6(Cook)
••.3gp, 3gp2
[Video] H.264/AVC, MPEG-4 Part2
[Audio] AAC, AMR(NB/WB)
••*DTS / *rm / *rmvb : Depending upon model
15
Supported Photo Formats
••Category : 2D (jpeg, jpg, jpe), 3D (jps)
[Available file type]
SOF0: Baseline,
SOF1 : Extend Sequential,
SOF2 : Progressive
[Photo size] Minimum : 64 x 64,
Maximum : Normal Type: 15360 (W) x 8640 (H),
Progressive Type : 1920 (W) x 1440 (H)
••Category : BMP
[Photo size] Minimum : 64 x 64
Maximum : 9600 x 6400
••Category : PNG
[Available file type] Interlace, Non-Interlace
[Photo size] Minimum : 64 x 64
Maximum : Interlace : 1200 x 800, Non-Interlace
: 9600 x 6400
••BMP and PNG format files may be slower to
display than JPEG.
Open Source Software Notice
Information
ENGLISH
To obtain the source code under GPL, LGPL, MPL,
and other open source licenses, that is contained
in this product, please visit http://opensource.lge.
com.
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices
are available for download.
LG Electronics will also provide open source code
to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of
media, shipping, and handling) upon email request
to opensource@lge.com. This offer is valid for three
(3) years from the date on which you purchased
the product.
Troubleshooting
The software may be updated for improvement
in performance. The customer is responsible to
ensure the compatibility of their equipment with
any LG Electronics software. If needed, please
consult with LG Electronics and update new
software versions according to the guidance
provided by LG Electronics.
••Cannot control the TV with the remote control.
- Check if anything such as tape has been placed
over the receiver.
- Check if there is any obstacle between the
product and the remote control.
- Replace the batteries with new fresh ones.
••No image display and no sound is produced.
- Check if the product is turned on.
- Check if the power cord is connected to a wall
outlet.
16
- Check if there is a problem in the wall outlet by
connecting other products.
••The TV turns off suddenly.
- Check the power control settings.
The power supply may be interrupted.
- Check if the Off Time / Sleep Timer feature is
activated in the TIME settings.
- If there is no signal while the TV is on, the TV
will turn off automatically after 15 minutes of
inactivity.
Licenses
Supported licenses may differ by model.
For more information about licenses,
visit www.lg.com.
Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are trademarks
of Dolby Laboratories.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
This DivX Certified® device has passed rigorous
testing to ensure it plays DivX® video.
To play purchased DivX movies, first register your
device at vod.divx.com. Find your registration
code in the DivX VOD section of your device
setup menu.
DivX Certified® to play DivX® video up to HD
1080p, including premium content.
DivX®, DivX Certified® and associated logos are
trademarks of DivX, LLC and are used under
license.
Covered by one or more of the following
U.S. patents: 7,295,673; 7,460,668; 7,515,710;
7,519,274.
Key Codes
••This feature is not available for all models.
Code
(Hexa)
Function
Note
Code
(Hexa)
Function
Note
CH +, PR +
R/C Button
53
List
R/C Button
01
CH -, PR -
R/C Button
5B
Exit
R/C Button
02
Volume +
R/C Button
60
PIP(AD)
R/C Button
03
Volume -
R/C Button
61
Blue
R/C Button
06
> (Arrow Key / Right Key)
R/C Button
63
Yellow
R/C Button
07
< (Arrow Key / Left Key)
R/C Button
71
Green
R/C Button
08
Power
R/C Button
72
Red
R/C Button
09
Mute
R/C Button
79
Ratio / Aspect Ratio
R/C Button
0B
Input
R/C Button
91
AD (Audio Description)
R/C Button
0E
SLEEP
R/C Button
7A
User Guide
R/C Button
0F
TV, TV/RAD
R/C Button
7C
Smart / Home
R/C Button
R/C Button
7E
SIMPLINK
R/C Button
10 - 19 * Number Key 0 - 9
1A
Q.View / Flashback
R/C Button
8E
►► (Forward)
R/C Button
1E
FAV (Favorite Channel)
R/C Button
8F
◄◄ (Rewind)
R/C Button
20
Text (Teletext)
R/C Button
AA
Info
R/C Button
21
T. Opt (Teletext Option)
R/C Button
AB
Program Guide
R/C Button
28
Return (BACK)
R/C Button
B0
► (Play)
R/C Button
30
AV (Audio / Video) Mode
R/C Button
B1
ꕗ (Stop / File List)
R/C Button
39
Caption/Subtitle
R/C Button
BA
ꕘ (Freeze / Slow Play / Pause)
R/C Button
40
Λ (Arrow Key / Cursor Up)
R/C Button
BB
Soccer
R/C Button
41
V (Arrow Key / Cursor Down)
R/C Button
BD
ꔄ (REC)
R/C Button
42
My Apps
R/C Button
DC
3D
R/C Button
43
Menu / Settings
R/C Button
99
AutoConfig
R/C Button
44
OK / Enter
R/C Button
9F
App / *
R/C Button
45
Q.Menu
R/C Button
9B
TV/PC
R/C Button
4C
List, - (ATSC Only)
R/C Button
ENGLISH
00
••Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
17
External Control Device Setup
••Image shown may differ from your TV.
Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an
A/V control system) to control the product’s functions externally.
Note: The type of control port on the TV can be different between model series.
••Please be advised that not all models support this type of connectivity.
••Cable is not provided.
USB to Serial Converter with USB Cable
USB IN
USB Type
(PC)
(TV)
••LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product
ID IN: 0x2008) USB to serial converter which is
RS-232C
(CONTROL & SERVICE)
not made nor provided by LG.
(TV)
(PC)
••It can be purchased from computer stores that carry accessories for IT support professionals.
SERVICE ONLY
USB IN
DE9 (D-Sub 9-pin) Type
1
3
••You need to purchase the RS-232C (DE9, D-Sub 9-pin female-to-female type) to RS-232C cable required for
(TV)
(PC)
(TV)
(PC)
the connection between the PC and the TV, which is specified in the manual.
••The connection interface may differ from your TV.
2
RS-232C IN
(CONTROL & SERVICE)
1
3
USBUSB
IN IN
(PC)
(PC)
(PC)
RS-232C IN
(TV)
(TV)
(TV)
(CONTROL & SERVICE)
2
SERVICE ONLY
Phone jack Type
1
RS-232C IN
3
(CONTROL & SERVICE)
••You need to purchase the phone-jack to RS-232 cable required
for the connection between the PC and the
RS-232C IN
(TV)
(PC)
(CONTROL & SERVICE)
TV, which is specified in the manual.
••For other models, connect to the USB port.
(TV)
(PC)
2
••The connection interface may differ from your TV.
1
3
(PC)
(PC)
(PC)
11
33
2RS-232C IN
SERVICE
ONLYONLY
SERVICE
ENGLISH
RS-232C With RS232C Cable
RS-232C IN
(CONTROL & SERVICE) (CONTROL & SERVICE)
22
(TV)
(TV)
(TV)
- or
1
3
(PC)
(PC)
1
3
RS-232C IN
2
2
18
RS-232C IN
(CONTROL & SERVICE)
(CONTROL & SERVICE)
RS-232C IN
(CONTROL & SERVICE)
(TV)
(TV)
Customer Computer
RS-232C Configurations
3-Wire Configurations(Not standard)
1
5
6
9
RS-232C
(Serial port)
PC
TV
RXD
2
2
TXD
TXD
3
1
RXD
GND
5
3
GND
OR
RXD
3
2
TXD
TXD
2
1
RXD
GND
5
3
GND
D-Sub 9
Phone
Set ID
For Set ID number, see Real Data Mapping.
1. Press SETTINGS to access the main menus.
ENGLISH
2. Press the navigation buttons to scroll to (General → About this TV or OPTION) and press OK.
3. Press the navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending upon model)
19
Communication Parameters
••Baud rate : 9600 bps (UART)
••Data length : 8 bits
••Parity : None
••Stop bit : 1 bit
••Communication code : ASCII code
••Use a crossed (reverse) cable.
Command Reference List
(Depending upon model)
01. Power*
COMMAND1
COMMAND2
DATA
(Hexadecimal)
k
a
00 to 01
DATA
(Hexadecimal)
COMMAND1
COMMAND2
15. Balance
k
t
00 to 64
ENGLISH
02. Aspect Ratio k
c
(page 22)
16. Color
(Colour)
Temperature
x
u
00 to 64
03. Screen Mute k
d
(page 22)
17. ISM Method
(Only Plasma
j
TV)
p
(page 24)
04. Volume
Mute
e
00 to 01
18. Equalizer
j
v
(page 24)
j
q
00 to 05
m
a
(page 24)
m
b
00 to 01
k
05. Volume
Control
k
f
00 to 64
19. Energy
Saving
06. Contrast
k
g
00 to 64
20. Tune
Command
07. Brightness
k
h
00 to 64
21. Channel
(Programme)
Add/Del(Skip)
i
00 to 64
22. Key
m
c
Key Codes
m
g
00 to 64
08. Color/Colour k
09. Tint
k
j
00 to 64
23. Control
Backlight,
Control Panel
Light
10. Sharpness
k
k
00 to 32
24. Input select x
(Main)
b
(page 26)
11. OSD Select
k
l
00 to 01
25. 3D (Only
3D models)
x
t
(page 26)
12. Remote
Control Lock
Mode
k
m
00 to 01
26. Extended
3D (Only 3D
models)
x
v
(page 27)
13. Treble
k
r
00 to 64
27. Auto
Configure
j
u
(page 27)
14. Bass
k
s
00 to 64
* Note:During playing or recording media, all commands except Power (ka) and Key (mc) are not executed
and treated as NG.
With RS232C cable, TV can communicate ka command in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
20
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]
First command to control the TV. (j, k, m or x)
[Command 2]
Second command to control the TV.
[Set ID]
You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] Carriage Return - ASCII code ‘0x0D’
[ ] Space – ASCII code ‘0x20’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data 00: Illegal Code
Real Data Mapping (Hexadecimal : Decimal)
••When you enter the [data] in hexadecimal, refer to following conversion table.
••Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0
32 : Step 50 (Set ID 50)
01 : Step 1 (Set ID 1)
33 : Step 51 (Set ID 51)
FE : Step 254
...
...
...
0A : Step 10 (Set ID 10)
63 : Step 99 (Set ID 99)
01 00 : Step 256
...
...
...
0F : Step 15 (Set ID 15)
C7 : Step 199
27 0E : Step 9998
10 : Step 16 (Set ID 16)
C8 : Step 200
27 0F : Step 9999
...
...
...
FF : Step 255
21
ENGLISH
The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the
PC computer.
••Commands may work differently depending upon model and signal.
01. Power (Command: k a)
▶▶ To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
Data 01 : *Power On
10 : Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
▶▶ To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK][Data][x]
04. Volume Mute (Command: k e)
▶▶ To control volume mute on/off.
You can also adjust mute using the MUTE button
on remote control.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
* Similarly, if other functions transmit ‘FF’ data
based on this format, Acknowledgement feedback
presents status about each function.
02. Aspect Ratio (Command: k c)
(Main Picture Size)
ENGLISH
▶▶ To adjust the screen format. (Main picture format)
You can also adjust the screen format using the
Aspect Ratio in the Q.MENU or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen(16:9)
04 : Zoom
05 : Zoom 2
(Latin America except
Colombia Only)
06 : Set by Program/
Original
07 : 14:9
(Europe, Colombia, MidEast, Asia except South
Korea and Japan)
09 : * Just Scan
0B : Full Wide
(Europe, Colombia, MidEast, Asia except South
Korea and Japan)
10 to 1F : C
inema Zoom
1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
••Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
••In DTV/HDMI/Component mode (highdefinition), Just Scan is available.
••Full wide mode may work differently based on
model and is supported for DTV fully, and ATV,
AV partially.
03. Screen Mute (Command: k d)
▶▶ To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : S
creen mute off (Picture on)
Video mute off
01 : S
creen mute on (Picture off)
22
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
▶▶ To adjust volume.
You can also adjust volume with the volume
buttons on remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
▶▶ To adjust screen contrast.
You can also adjust contrast in the PICTURE
menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
12. Remote control lock mode (Command: k m)
▶▶ To adjust screen brightness.
You can also adjust brightness in the PICTURE
menu.
▶▶ To lock the front panel controls on the monitor and
remote control.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
08. Color/Colour (Command: k i)
▶▶ To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
Data 01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this
mode.
When main power is off & on (plug-off and plug-in,
after 20 - 30 seconds), external control lock is
released.
* In the standby mode (DC off by off timer or ‘ka’, ‘mc’
command), and if key lock is on, TV will not turn on
by power on key of IR & Local Key.
13. Treble (Command: k r)
09. Tint (Command: k j)
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
ENGLISH
▶▶ To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
▶▶ To adjust treble.
You can also adjust in the AUDIO menu.
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
* (Depending upon model)
14. Bass (Command: k s)
10. Sharpness (Command: k k)
▶▶ To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE
menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 32
▶▶ To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
* (Depending upon model)
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
15. Balance (Command: k t)
11. OSD Select (Command: k l)
▶▶ To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
Data 01 : OSD on
▶▶ To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
23
16. Color(Colour) Temperature (Command: x u)
▶▶ To adjust colour temperature. You can also adjust
Color(Colour) Temperature in the PICTURE menu.
* (Depending upon model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
20. Tune Command (Command: m a)
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. ISM Method (Command: j p) (Only Plasma TV)
▶▶ To control the ISM method. You can also adjust
ISM Method in OPTION menu.
* This command may work differently depending
upon model and signal.
• For Europe, Mid-East, Colombia, Asia except South
Korea and Japan Model
▶▶ Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ]
[Data 01][ ][Data 02][Cr]
Transmission [j][p][ ][Set ID][ ][Data][Cr]
* Analog Antenna/Cable
Data Min : 02: Orbiter
08: Normal
20: Color(Colour) Wash
[Data 00][Data 01] Channel Data
Data 00 : High byte channel data
Data 01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog)
- 00 : Antenna TV (ATV)
- 80 : Cable TV (CATV)
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
18. Equalizer (Command : j v)
▶▶ Adjust EQ of the set.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
ENGLISH
MSB
0
* Digital Antenna/Cable/Satellite
LSB
0
0
0
0
Frequency
0
0
[Data 00][Data 01]: Channel Data
Data 00 : High Channel data
Data 01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
0
Data
7
6
5
Frequency
4
3
2
1
0
Step
0
0
0
0
1
0
0
1
1
0
0
1
0
1
0
1st Band
2nd Band
3rd Band
4th Band
5th Band
0
0
...
1
1
0
0
...
0
0
0
0
...
0
1
0
0
...
1
0
0
1
...
1
0
0 (decimal)
1 (decimal)
...
19 (decimal)
20 (decimal)
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]
* It depends on model, and can adjust when sound
mode is EQ adjustable value.
19. Energy Saving (Command: j q)
▶▶ To reduce the power consumption of the TV. You
can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Data
00 : Off
01 : Minimum
02 : Medium
03 : Maximum
04 : Auto (For LCD TV / LED TV) /
Intelligent sensor (For PDP TV)
05 : Screen off
24
Data 02 : Input Source (Digital)
- 10 : Antenna TV (DTV)
- 20 : Antenna Radio (Radio)
- 40 : Satellite TV (SDTV)
- 50 : Satellite Radio (S-Radio)
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
* Tune Command Examples:
1. Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00
Data 00 & 01 = Channel Data is 10 = 00 0a
Data 02 = Analog Antenna TV = 00
Result = ma 00 00 0a 00
2. Tune to the digital antenna (DVB-T) Channel 01.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1 = 00 01
Data 02 = Digital Antenna TV = 10
Result = ma 00 00 01 10
3. Tune to the satellite (DVB-S) Channel 1000.
Set ID = All = 00
Data 00 & 01 = Channel Data is 1000 = 03 E8
Data 02 = Digital Satellite TV = 40
Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
• For South Korea, North/Latin America except
Colombia Model
▶▶ To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor
channel number. The Physical number is the actual
digital channel number, the Major is the number that
the channel should be mapped to, and the Minor is
the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
the Physical number is not required when sending a
command in Digital.
* Analog Antenna/Cable
* Digital Antenna/Cable
Data 00 : xx (Don't care)
[Data 01][Data 02]: Major Channel Number
Data 01 : High byte Channel Data
Data 02 : Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor Channel Number
Data 03 : High byte Channel Data
Data 04 : Low byte Channel Data
2.Tune to the digital antenna (ATSC) channel 30-3.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = Digital Antenna TV = 22
Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
• For Japan Model
▶▶ To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
* Digital Antenna/Satellite
Data 00: xx (Don't care)
ENGLISH
Data 00 : Physical Channel Number
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number
Data 01 & 02: xx (Don't care)
Data 03 & 04: xx (Don't care)
Data 05: Input Source (Analog)
- 00 : Antenna TV (ATV)
- 01 : Cable TV (CATV)
* Tune Command Examples:
1.Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01
Total = ma 00 23 00 00 00 00 01
[Data 01][Data 02]: Major Channel Number
Data 01: High byte Channel Data
Data 02: Low byte Channel Data
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number
(Don’t care in Satellite)
Data 03: High byte Channel Data
Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Antenna TV (DTV)
- 07 : BS (Broadcasting Satellite)
- 08 : CS1 (Communication Satellite 1)
- 09 : CS2 (Communication Satellite 2)
Data 05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel
Number
- 06 : Cable TV (CADTV) – Use Physical Channel
Number
- 22 : Antenna TV (DTV) – Don’t Use Physical
Channel Number
- 26 : Cable TV (CADTV) - Don’t Use Physical
Channel Number
- 46 : Cable TV (CADTV) – Use Major Channel
Number Only (One Part Channel)
Two bytes are available for each major and minor
channel data, but usually the low byte is used alone
(high byte is 0).
25
* Tune Command Examples:
1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
Data 05 = Digital Antenna TV = 02
Total = ma 00 00 00 11 00 01 02
2. Tune to the BS (ISDB-BS) channel 30.
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Don’t Care = 00 00
Data 05 = Digital BS TV = 07
Total = ma 00 00 00 1E 00 00 07
* This feature is varied based on the model.
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
[Data 02][Data 03][Data 04][Data 05]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
• For Plasma TV
▶▶ To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
24. Input select (Command: x b)
(Main Picture Input)
▶▶ To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
21. Channel(Programme) Add/Del(Skip) (Command:
m b)
Data
00 : D
TV
02 : S
atellite DTV
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan)
04 : ISDB-CS2 (Japan)
11 : CATV
▶▶ To skip current channel(programme) for next time.
20 : AV or AV1
21 : AV2
40 : Component1
60 : RGB
41 : Component2
90 : HDMI1
92 : HDMI3
91 : HDMI2
93 : HDMI4
[x][a][ ][Set ID][ ][NG][Data 00][x]
ENGLISH
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Del(ATSC,ISDB)/Skip(DVB)
Data 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Set the saved channel status to del(ATSC, ISDB)/
skip(DVB) or add.
22. Key (Command: m c)
▶▶ To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - page 17.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
23. Control Backlight (Command: m g)
• For LCD TV / LED TV
▶▶ To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
26
01 : CADTV
10 : ATV
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* This function depends on model and signal.
25. 3D(Command: x t) (only 3D models)
(Depending upon model)
▶▶ To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr]
* (Depending upon model)
DataStructure
[Data 00]00 : 3D On
01 : 3D Off
02 : 3D to 2D
03 : 2D to 3D
[Data 01]00 : Top and Bottom
01 : Side by Side
02 : Check Board
03 : Frame Sequential
04 : Column interleaving
05 : Row interleaving
[Data 02]00 : Right to Left
01 : Left to Right
[Data 03]3D Effect(3D Depth): Min : 00 - Max : 14
(*transmit by Hexadecimal code)
* If [Data 00] is 00 (3D On), [Data 03] has no
meaning.
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data
01], [Data 02] and [Data 03] have no meaning.
* If [Data 00] is 03 (2D to 3D), [Data 01] and
[Data 02] have no meaning.
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data
03] works when 3D Mode (Genre) is manual only.
* All 3D pattern options ([Data 01]) may not be
available according to broadcasting/video signal.
[Data 00]
[Data 01]
[Data 02]
[Data 03]
00
O
O
O
01
X
X
X
02
X
X
X
03
X
O
O
X : don’t care
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
[Data03][x]
[t][ ][Set ID][ ][NG][Data00][x]
▶▶ To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
2) When[Data 00] is 01, 02
DataMin: 0 - Max: 14 (*transmit by Hexadecimal
code)
Data value range(0 - 20) converts Viewpoint range
(-10 - +10) automatically (Depending upon model)
* This option works when 3D Mode (Genre) is manual
only.
3) When[Data 00] is 06, 07
00 : Off
01 : On
4) When[Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
converted 2D video
01 : Change 3D video to 2D video, except
2D-to-3D video
* If conversion condition doesn’t meet, command is
treated as NG.
5) When [Data 00] is 09
00 : Standard
02 : Cinema
04 : Manual
01 : Sport
03 : Extreme
05 : Auto
ENGLISH
26. Extended 3D(Command: x v) (only 3D models)
(Depending upon model)
[Data 01]It has own range for each 3D option
determined by [Data 00].
1) When[Data 00] is 00
00 : Right to Left
01 : Left to Right
Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]
[v][ ][Set ID][ ][NG][Data00][x]
[Data 01][Cr]
[Data 00]3D option
00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
06 : 3D Color Correction
07 : 3D Sound Zooming
08 : Normal Image View
09 : 3D Mode (Genre)
27. Auto Configure (Command: j u)
(Depending upon model)
▶▶ To adjust picture position and minimize image
shaking automatically. It works only in RGB (PC)
mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
27
LG Customer Information Center
Declaration of Conformity
Trade Name: LG
Model: 32LX330C-UA, 42LX330C-UA, 49LX341C-UA,
55LX341C-UA, 60LX341C-UA, 65LX341C-UA,
42LX530S-UA
49LX540S-UA, 55LX540S-UA, 60LX540S-UA,
65LX540S-UA, 43LX310C-UA, 49LX310C-UA
Responsible Party: LG Electronics Inc.
Address: 1000 Sylvan Ave.
Englewood Cliffs NJ 07632
U.S.A
TEL: 201-266-2534
For inquires or comments, visit www.lg.com or call;
1-888-542-2623
CANADA
1-888-865-3026
USA, Commercial User
The model and serial numbers of the TV are located
on the back and on one side of the TV. Record them
below should you ever need service.
MODEL
SERIAL
ENGLISH Easy Setup Guide
Please read this manual carefully before operating your set and retain it for future reference.
ESPAÑOL Guía Rápida de Configuración
Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas.
FRANÇAIS Guide de configuration rapide
Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et le conserver pour pouvoir vous y reporter
ultérieurement.
LED TV
32LX330C
42LX330C
42LX530S
AAA
a X4
(M4 X L20)
32LX330C
b X4
(M4 X L14)
42LX330C
42LX530S
X2
42LX530S
42LX330C
www.lg.com
P/NO : MFL68884902 (1504-REV01)
i
1
ENGLISH
ESPAÑOL
FRANÇAIS
Read Safety and Reference.
Leer Seguridad y Consultas.
Lisez Sécurité et références.
1
2
1
2
3
4
a/ b
2
ENGLISH
ESPAÑOL
FRANÇAIS
Image shown may differ from your TV.
La imagen puede ser diferente a la de su televisor.
Cette illustration peut ne pas correspondre à votre téléviseur.
A
1 : 32/42LX330C
A
B
2
A
B
1
2 : 42LX530S
B
ENGLISH Image shown may differ from your TV.
ESPAÑOL La imagen puede ser diferente a la de su televisor.
FRANÇAIS Cette illustration peut ne pas correspondre à votre
téléviseur.
1 42LX530S
1
3
4
1
2
3
4
5
ENGLISH
MODELS
With stand
Dimensions
(W x H x D)
Without stand
With stand
Without stand
Power requirement
Current value / Power consumption
Weight
32LX330C
(32LX330C-UA)
42LX330C
(42LX330C-UA)
42LX530S
(42LX530S-UA)
732 x 481 x 207 (mm)
961 x 612 x 218 (mm)
28.8 x 18.9 x 8.1
37.8
x 24 x 8.5 (inches)
(inches)
732 x 437 x 55.5 (mm)
961 x 567 x 55.5 (mm)
28.8 x 17.2 x 2.1
37.8
x 22.3 x 2.1 (inches)
(inches)
6.2 kg (13.6 lbs)
9.5 kg (20.9 lbs)
6.0 kg (13.2 lbs)
9.2 kg (20.2 lbs)
AC 100 - 240 V ~ 50 / 60 Hz
1.1 A / 65 W
0.9 A / 90 W
ESPAÑOL
FRANÇAIS
MODELOS
MODÈLES
Con base
Dimensiones
(Ancho x altura
x profundidad) Avec support
Sin base
Dimensions
(L x H x P)
Sans support
Con base
Avec support
Sin base
Poids
Sans support
Potencia requerida
Alimentation
Corriente de consumo /
Consumo de la potencia
Valeur courante /
Consommation électrique
Peso
732 x 481 x 207 (mm)
28,8 x 18,9 x 8,1
(pulgadas / pouces)
42LX330C
(42LX330C-UA)
42LX530S
(42LX530S-UA)
961 x 612 x 218 (mm)
37,8 x 24 x 8,5
(pulgadas / pouces)
732 x 437 x 55,5 (mm)
28,8 x 17,2 x 2,1
(pulgadas / pouces)
961 x 567 x 55,5 (mm)
37,8 x 22,3 x 2,1
(pulgadas / pouces)
6,2 kg (13,6 libras / lb)
9,5 kg (20,9 libras / lb)
6,0 kg (13,2 libras / lb)
9,2 kg (20,2 libras / lb)
32LX330C
(32LX330C-UA)
AC 100 - 240 V ~ 50 / 60 Hz
1,1 A / 65 W
0,9 A / 90 W
*MFL68884902*
(For USA and Canada only)
(Para Estados Unidos y Canadá)
This product qualifies for ENERGY STAR
in the factory default (Home
configuration) setting. Changing the
factory default settings or enabling
other features may increase power consumption
that could exceed the limits necessary to quality
for ENERGY STAR. Refer to ENERGYSTAR.gov for
more information on the ENERGY STAR program.
(Pour les États-Unis et le Canada)
Ce produit est conforme aux normes
ENERGY STAR lorsque le réglage
d’usine par défaut (Résidentiel) est
sélectionné. Modifier les réglages
d’usine par défaut ou activer d’autres
fonctionnalités augmente la consommation
d’énergie qui pourrait alors dépasser les limites de
la qualification Energy Star. Consultez le site
ENERGYSTAR.gov pour en savoir plus au sujet du
programme ENERGY STAR.
Download PDF

advertising