LG | 47TS30MF-B | LG 47TS30MF-B Owner’s Manual

ENG
ENGLISH
OWNER’S MANUAL
MONITOR SIGNAGE
Please read this manual carefully before operating the your set and
retain it for future reference.
MONITOR SIGNAGE MODELS
26TS30MF
47TS30MF
www.lg.com
2
CONTENTS
ENGLISH
ENG
CONTENTS
3
INSTALLATION PREPARATION
3
Accessories
4
Mounting Holes
6
Unpacking and Cabling
8
Portrait Layout (Only supported for 47TS30MF)
9
Storage Method for Panel Protection
9
- Correct Method
9
- Incorrect Method
10 PRODUCT INSTALLATION
10
Lighting Installation
11
Installation in Enclosure
12
Precaution
12
- Correct Method
12
- Incorrect Method
13 TROUBLESHOOTING
14 SPECIFICATIONS
14
26TS30MF
15
47TS30MF
16 LVDS PIN MAP GUIDE
16
26TS30MF
17
47TS30MF
NOTE
The warranty will not cover any damages caused by using the product in an excessively dusty
yy
environment.
INSTALLATION PREPARATION
3
Accessories
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and accessories.
CD (Owner's Manual)/
Easy Setup Guide
CAUTION
Do not use any unapproved or counterfeit parts or accessories to ensure the safety and product life
yy
span.
Any damages or injuries by using unapproved items are not covered by the warranty.
yy
NOTE
The accessories supplied with your product may vary depending on the model.
yy
Product specifications or contents in this manual may be changed without prior notice due to upgrade
yy
of product functions.
ENG
ENGLISH
INSTALLATION PREPARATION
4
INSTALLATION PREPARATION
Mounting Holes
ENGLISH
ENG
26TS30MF
Use M3 x 4 mm screws to mount the monitor. There are 16 positions for screws on the rear side of the
product.
Front side of the product
Rear side of the product
INSTALLATION PREPARATION
Use M3 x 4 mm screws to mount the monitor. There are 20 positions for screws on the rear side of the
product.
Front side of the product
Rear side of the product
CAUTION
This product has the front and back sides. Make sure the product is installed with the front side facing
yy
forward.
Image is displayed reversely on the back side.
yy
ENG
ENGLISH
47TS30MF
5
6
INSTALLATION PREPARATION
Unpacking and Cabling
ENGLISH
ENG
26TS30MF
1 Lift up the cover of the box.
2 Remove the top packaging.
3 Hold both sides of the product and lift it up.
4 Remove the poly bag.
5 Place a soft cloth on the table and put the
6 Connect the LVDS cable(Additional assembly
product down with the screen facing downward.
is required). A scaler board or LVDS cable is
optional and not provided with the product.
INSTALLATION PREPARATION
7
47TS30MF
2 Remove the top packaging.
3 Hold both sides of the product and lift it up.
4 Remove the poly bag.
5 Place a soft cloth on the table and put the
6 Connect the LVDS cable(Additional assembly
product down with the screen facing downward.
is required). A scaler board or LVDS cable is
optional and not provided with the product.
NOTE
Please refer to "LVDS Pin Map Guide" on pages 16 to 18 for the LVDS cable assembly.
yy
ENG
ENGLISH
1 Lift up the cover of the box.
8
INSTALLATION PREPARATION
Portrait Layout (Only supported for 47TS30MF)
ENGLISH
ENG
To install in portrait mode, rotate the set clockwise 90 degrees when looking at from the front.
The portrait mode is only available on the scaler board. (The scaler board should support portrait mode.)
CAUTION
The 26TS30MF model cannot be rotated.
yy
The scaler board is optional and it is not part of the product.
yy
INSTALLATION PREPARATION
9
Storage Method for Panel Protection
Panel
ENG
ENGLISH
Correct Method
Incorrect Method
Cushion
Panel
When laying the product on a flat floor, pit it face
down on a cushion or blanket to prevent scratching and damage.
Panel
If there is no a cushion or a soft cloth available,
ensure the floor is clean. Then lay the product
down carefully with the panel facing either upward
or downward. At this time, make sure that no
object falls on the panel.
If the product is tilted onto the bezel, the bottom of
the panel may be damaged.
Panel
If the product is tilted onto the edge of the panel,
the panel may be damaged.
10
PRODUCT INSTALLATION
ENGLISH
ENG
PRODUCT INSTALLATION
Lighting Installation
This product must be installed with backlighting.
Lighting must be installed behind the product so that the display can be seen clearly.
600 lux or more
(When the Full Screen
is White.)
Lighting
If something obstructs the backlighting, additional lighting may be required.
Additional lighting
600 lux or more
(When the Full Screen
is White.)
Object
Lighting
Additional lighting
PRODUCT INSTALLATION
11
Installation in Enclosure
ENG
ENGLISH
Install the product in the enclosure. Wear working
gloves when installing the product. Do not use
bare hands. Otherwise, it may cause personal
injury.
1 Place the product in the enclosure.
2 Attach the product using the prepared screw
holes and an additional enclosure guide frame.
Example of the product in the enclosure
NOTE
This product can be installed in various
yy
locations besides the enclosure.
Example of the lighting installation
Lighting must be installed in the enclosure.
CAUTION
The panel of this product is so thin that it can
yy
be easily broken when it is exposed to the
outside. Use a clear protective cover to keep
the product from exposure to the elements.
12
PRODUCT INSTALLATION
Precaution
ENGLISH
ENG
Correct Method
Incorrect Method
Do not hold the screen area when holding the
product.
Do not lift up the product by holding a corner.
CAUTION
Use a soft cloth moistened with n-hexane to
remove dust or stains on the screen.
CAUTION
If a fixed image displays on the screen for a
yy
long period of time, it will be imprinted and
become a permanent disfigurement on the
screen. This is image burn or burn-in and not
covered by the warranty.
To prevent image sticking, do not play a still
yy
image for more than two hours.
Recommended operation time for optimum
yy
performance and reliability is 12 hours or
less per day.
Make sure the power is disconnected before
yy
moving or installing the product. Otherwise
electric shock may occur.
Wear working gloves when installing the
yy
product. Do not use bare hands. Otherwise,
it may cause personal injury.
If you install the product on a ceiling or
yy
slanted wall, it may fall and result in severe
injury.
Do not fasten the screws too tightly; this may
yy
cause damage to the product and void your
warranty.
Use M3 x 4 mm screws to mount the
yy
monitor. Any damages or injuries caused by
misuse or use of improper accessories are
not covered by the warranty.
TROUBLESHOOTING
13
After-image appears on the product.
Problem
After-image appears when the
product is turned off.
Resolution
yy If you use a fixed image for a long time, the pixels may be damaged
quickly. Use the screen-saver function.
yy When a dark image is displayed on the screen after an image with
high contrast (black and white or gray), this may cause image sticking.
This is normal for LCD screen.
Screen color is abnormal.
Problem
creen color is unstable or
S
mono-colored.
Do black spots appear on the
screen?
Resolution
yy Check the connection status of the LVDS cable.
yy Check whether the LVDS cable is connected correctly following the
LVDS Pin Map Guide.
yy Several pixels (red, green, white or black color) may appear on the
screen, which can be attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
ENG
ENGLISH
TROUBLESHOOTING
14
SPECIFICATIONS
ENGLISH
ENG
SPECIFICATIONS
26TS30MF
EEPROM
RGB
Source Driver Circuit
SCL
SDA
S1
S1366
G1
LVDS Select #9
CN1
(30pin)
LVDS 1Port
Timing Controller
[LVDS Rx]
TFT - LCD Panel
Control
Signals
(1366 x RGB x 768 pixels)
[Gate In Panel]
+12.0V
Power Circuit
Block
G768
Power Signals
Screen Size
26.01 inche (660.6 mm) diagonal
Dimension(W x H x D)
609 mm x 412.8 mm x 8.8 mm
Pixel Pitch
0.1405 mm x RGB x 0.4215 mm
Pixel Format
1366 horiz. by 768 vert. pixels RGB stripe arrangement
Color Depth
8bit(D), 16,7 M colors
Transmittance (With POL)
4.84 % (Typ.)
Viewing Angle (CR>10)
Viewing angle free ( R/L 178(Min.), U/D 178(Min.))
Power Consumption
Total 2.7 W (Typ)(TBD)
Weight(head)
1.62 kg
Display Operating Mode
Transmissive mode, Normally black
Surface Treatment (Top)
Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 10 %)
Possible Display Type
Landscape only
SPECIFICATIONS
ENG
ENGLISH
47TS30MF
Mini-LVDS
(RGB)
EEPROM
Source Driver Circuit
SCL
LVDS 2Port
LVDS 1,2
LVDS Select
Option
signal
CN1
Bit Select
15
(51pin)
SDA
S1
G1
Timing Controller
LVDS Rx + DCA + ODC
Intergrated
TFT - LCD Panel
(1920 x RGB x 1080 pixels)
[Gate In Panel]
Control
Signals
I2C
S1920
+12.0V
G1080
Power Circuit
Block
Power Signals
Screen Size
46.96 inch (1192.87mm) diagonal
Dimension(W x H x D)
1165.9 mm x 663.27 x 8.8 mm
Pixel Pitch
0.5415 mm x 0.5415 mm
Pixel Format
1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement
Color Depth
10Bit (D), 1.07 Billion colors
Transmittance (With POL)
5,5 %(Typ.)
Viewing Angle (CR>10)
Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))
Power Consumption
Total 6.6W (Typ.)(TBD)
Weight(head)
4.56 kg
Display Operating Mode
Transmissive mode, Normally black
Surface Treatment (Top)
Hard coating(3H), Anti-glare treatment (Reflectance < 2 %),
Possible Display Type
Landscape and Portrait Enabled
16
LVDS PIN MAP GUIDE
ENGLISH
ENG
LVDS PIN MAP GUIDE
26TS30MF
LVDS Connector(CN1) : KDF71G-30S-1H(Hirose) or Compatible, Refer to below table.
yy
Mating Connector : FI-X30C2L(Manufactured by JAE) or Equivalent
yy
Cable length: 1 m of FFC cable or less
yy
Pin No.
Symbol
1
VLCD
Power Supply+12.0V
Description
2
VLCD
Power Supply+12.0V
3
VLCD
Power Supply+12.0V
4
VLCD
Power Supply+12.0V
5
GND
Ground
6
GND
Ground
7
GND
Ground
8
GND
Ground
9
LVDS Select
Note
'H' = JEIDA, 'L' or NC = VESA
10
NC
11
GND
No Connection
Ground
4
12
RA-
LVDS Receiver Signal(-)
13
RA+
LVDS Receiver Signal(+)
14
GND
Ground
15
RB-
LVDS Receiver Signal(-)
16
RB+
LVDS Receiver Signal(+)
17
GND
Ground
18
RC-
LVDS Receiver Signal(-)
19
RC+
LVDS Receiver Signal(+)
20
GND
Ground
21
RCLK-
LVDS Receiver Clock Signal(-)
22
RCLK+
LVDS Receiver Clock Signal(+)
23
GND
Ground
24
RD-
LVDS Receiver Signal(-)
25
RD+
LVDS Receiver Signal(+)
26
GND
Ground
27
NC
No Connection (Note 4)
4
28
NC
No Connection (Note 4)
4
29
NC
No Connection (Note 4)
4
30
GND
Ground
Note : 1. All GND (Ground) pins should be connected together to the LCD module's metal frame.
2. All VLCD (power input) pins should be connected together.
3. All Input levels of LVDS signals are based on the EIA 644 Standard.
4. These pins are used only for LGD (Do not connect).
LVDS PIN MAP GUIDE
17
47TS30MF
ENG
ENGLISH
LVDS Connector(CN1) : FI-RE51S-HF or Equivalent, Refer to below table.
yy
Mating Connector : FI-RE51S or Equivalent
yy
Cable length: 1 m of coaxial cable or less
yy
Pin No.
Symbol
1
GND
2
3
Description
Note
Ground
1
NC
No Connection
4
NC
No Connection
4
4
NC
No Connection (Reserved for LGD)
4
5
NC
No Connection (Reserved for LGD)
4
6
NC
No Connection (Reserved for LGD)
4
7
LVDS Select
8
NC
No Connection
'H' = JEIDA, 'L' or NC = VESA
9
NC
No Connection
10
NC
No Connection
11
GND
Ground
12
RO0N
FIRST LVDS Receiver Signal(A-)
13
RO0P
FIRST LVDS Receiver Signal(A+)
14
RO1N
FIRST LVDS Receiver Signal(B-)
15
RO1P
FIRST LVDS Receiver Signal(B+)
16
RO2N
FIRST LVDS Receiver Signal(C-)
17
RO2P
FIRST LVDS Receiver Signal(C+)
18
GND
Ground
19
ROCLKN
FIRST LVDS Receiver Clock Signal(A-)
20
ROCLKP
FIRST LVDS Receiver Clock Signal(A+)
1
1
21
GND
Ground
22
RO3N
FIRST LVDS Receiver Signal(D-)
1
23
RO3P
FIRST LVDS Receiver Signal(D+)
24
RO4N
FIRST LVDS Receiver Signal(E-)
5
25
RO4P
FIRST LVDS Receiver Signal(E+)
5
26
NC
27
Bit Select
28
RE0N
SECOND LVDS Receiver Signal(A-)
29
RE0P
SECOND LVDS Receiver Signal(A+)
30
RE1N
SECOND LVDS Receiver Signal(B-)
31
RE1P
SECOND LVDS Receiver Signal(B+)
32
RE2N
SECOND LVDS Receiver Signal(C-)
33
RE2P
SECOND LVDS Receiver Signal(C+)
34
GND
Ground
35
RECLKN
SECOND LVDS Receiver Clock Signal(-)
36
RECLKP
SECOND LVDS Receiver Clock Signal(+)
37
GND
Ground
38
RE3N
SECOND LVDS Receiver Signal(D-)
39
RE3P
SECOND LVDS Receiver Signal(D+)
40
RE4N
SECOND LVDS Receiver Signal(E-)
5
41
RE4P
SECOND LVDS Receiver Signal(E+)
5
No Connection
'H' or NC = 10bit(D), 'L' = 8bit
1
1
18
LVDS PIN MAP GUIDE
ENGLISH
ENG
Pin No.
Symbol
42
NC
No Connection
Description
Note
43
NC
No Connection
44
NC
No Connection
45
GND
Ground
46
GND
Ground
47
GND
Ground
48
VLCD
Power Supply+12.0V
2
49
VLCD
Power Supply+12.0V
2
50
VLCD
Power Supply+12.0V
2
51
VLCD
Power Supply+12.0V
2
Note : 1. All GND (Ground) pins should be connected together to the LCD module's metal frame.
2. All VLCD (power input) pins should be connected together.
3. All Input levels of LVDS signals are based on the EIA 644 Standard.
4. Specific pins(pin No. #2~#6) are used for internal data process of the LCD module.
These pins should be no connections.
5. LVDS pin (pin No. #24,25,40,41) are used for 10Bit (D) of the LCD module.
If used for 8Bit (R), these pins are no connection.
Make sure to read the Safety Precautions
before using the product.
Keep the Owner's Manual(CD) in an
accessible place for future reference.
The model and serial number of the SET
is located on the back and one side of the
SET. Record it below should you ever need
service.
MODEL
SERIAL
Temporary noise is normal when powering ON
or OFF this device.
Download PDF

advertising