LG | L1730BSFT | LG L1730BSFT Owner’s Manual

User's Guide
L1730B
FT
L1930B
FT
L1930BQ
Make
sure
to read the
Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached
dealer when you
on
the back cover and quote this information to your
require service.
Precautions
Important
This unit has been
engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On
Safety
power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
Use
only the
manufacturer
or
the nearest authorized
repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords
cords and broken
plugs. They
technician for replacement.
Do not
Open
There
the
may result in
are
a
dangerous. So
shock
or
are
frayed
power
fire hazard. Call your service
Display.
serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
are no user
To Avoid Personal
Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire
or
Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
A1
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not
the display where the power cord is subject to damage.
Do not
use
this
display
sink, laundry tub, in
near water
a wet
such
basement,
as near a
or near a
place
bathtub, washbowl, kitchen
swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
can cause
strike the Active Matrix LCD with anything hard
damage the Active Matrix LCD permanently.
Do not rub
mar, or
or
Do not press the LCD
some
screen
with your
finger for a long
time
as
as
this may scratch,
this may
cause
afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If
possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On
Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly
screen because over-spraying may cause electrical shock.
On
on
the
display
Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
On
Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of
your local authority.
Connecting
Before
the
Display
setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting
the stand base
1. Place the monitor with its front facing downward on a cushion or soft cloth.
2. Align the hooks on the stand base with the matching slots in the base of
the monitor.
3.
Hook
Insert the hooks into slots.
Removing
1.
2.
the stand base
Place the monitor with its front
To
remove
downward
facing
on a
cushion
the stand base, hold the bottom of the stand with
pull the base bottom latch with the other hand,
as
soft cloth.
or
one
shown in the
hand and
figure.
Bottom Latch
Important
This illustration
the
depicts the general
items shown in the picture.
model of connection. Your monitor may differ from
Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only the stand base. The
fall and get damaged or injure your foot.
In order to prevent injury, watch that your
sliding
door
or
attaching/detaching
a
fingers
stand
cover.
A3
are
not
product
caught when moving
a
may
Connecting
Using
the
the
Display
Computer
1. Open the Sliding Door and remove the Stand Cover.
Sliding
Door
Stand Cover
2. Connect the signal cable. When attached, tighten the thumbscrews to secure
the connection.
3. Connect the power cord into a proper power outlet that is easily accessible and
close to the
display.
Analog signal
*
Digital signal
Varies according to model.
Wall-outlet
PC-outlet
PC
2
type*
type*
1
DVI-D cable (not
included)
D-SUB cable
MAC
Mac adapter
For Apple Macintosh use,
separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
A4
a
Connecting
4.
the
Display
Connect the cables
as
shown in the
figure to the
cable holder to arrange it
neatly.
Cable Holder
5. Connect the Stand Cover and then pull down the Sliding Door.
Sliding
Door
Stand Cover
6.
Press
button
on
the front switch
monitor power is turned on,
executed automatically.
panel to turn the power on. When
the 'Self Image Setting Function' is
PROCESSING
IMAGE
SELF
SETTING
NOTE
'
Image Setting Function'? This function provides the user with optimal display
settings.When the user connects the monitor for the first time, this function automatically
adjusts the display to optimal settings for individual input signals. If you want to adjust the
monitor while in use, or wish to manually run this function once again, push the 'AUTO'
button on the front panel of the monitor. Otherwise, you may execute the 'FACTORY
RESET' option on the OSD adjustment menu. However, be aware that this option initializes
Self
all the
menu
items except 'LANGUAGE'.
A5
Control Panel Functions
Front Panel Controls
+
-
Bottom
+
-
Control
Function
MENU Button
Use this button to enter
or
exit the On Screen
Display.
OSD LOCKED/UNLOCKED
This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
OSD
LOCKED
Press and hold the MENU button for 5 seconds. The
message "OSD LOCKED" should appear.
OSD
UNLOCKED
You
unlock the OSD controls at any time by pushing
the MENU button for 5 seconds. The message "OSD
can
UNLOCKED" should appear.
Buttons
Use these buttons to select
Screen
adjust functions
in the On
Display.
Button
hot
For
or
more
key
information, refer
FLATRON
to page A13
F-ENGINE
USER
NORMAL
MENU
Button
-
SOURCE hot
+
SET
key
Use this button to make Dsub
or
DVI connector
active. This feature is used when two computers are
connected to the display. The default setting is Dsub.
A6
Control Panel Functions
Control
Function
SET/AUTO
Use this button to enter
a
selection in the On Screen
Display.
Button
AUTO IMAGE ADJUSTMENT
When
adjusting
your display settings, always press
the SET/AUTO button before entering the On Screen
Display(OSD). This will automatically adjust your
display image to the ideal settings for the current
screen resolution size (display mode).
The best
display
mode is
17 inch monitor
:
1280x1024
19 inch monitor
:
1280x1024
PROCESSING
IMAGE
AUTO
ADJUSTMENT
Power Button
Use this button to turn the
Power
This Indicator
(DPMS)
Indicator
display
on or
off.
lights up green when the display
operates normally. If the display is in DPM (Energy
Saving) mode, this indicator color changes to amber.
A7
On Screen
Screen
Display (OSD) Control Adjustment
Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the
To make
display to
stabilize for at least 30 minutes before
adjustments
in the On Screen
-+
MENU
Display, follow these steps:
SET/AUTO
Press the MENU Button, then the main
To
access a
becomes
Use the
control,
highlighted,
/
Buttons to
SET/AUTO Button
menu
-+
MENU
of the OSD appears.
Buttons. When the icon you want
press the SET/AUTO Button.
use
the
making image adjustments.
or
adjust the image
to the desired level. Use the
to select other sub-menu items.
Push the MENU Button
once to return to
the main
menu to
select another
function. Push the MENU Button twice to exit from the OSD.
Automatic
save
With the OSD open,
you have made an adjustment the monitor
automatically save any adjustments you have made, even if you exit the menu
or open another menu. If you make an adjustment and then wait for the
OSD to
once
disappear, the adjustment will also been saved.
A8
On Screen
Display(OSD)
Selection and
Adjustment
following table indicates all the On Screen Display control, adjustment,
and setting menus.
The
Main
menu
PICTURE
Sub
A
menu
D
Reference
BRIGHTNESS
To
CONTRAST
and gamma of the
adjust the brightness,
contrast
screen
GAMMA
PRESET
COLOR
To customize the color of the
screen
RED
GREEN
BLUE
H POSITION
To
V POSITION
screen
CLOCK
To
and
PHASE
improve the clarity
stability of the screen
FACTORY
FACTORY RESET
To restore the default
settings
RESET
WHITE BALANCE
POSITION
TRACKING
SETUP
adjust the position
LANGUAGE
To customize the
OSD H POSITION
for
a
user's
of the
screen
operating
status
environment
OSD V POSITION
TEXT/ MOVIE
FLATRON
F-ENGINE(
-
)
To select
USER
or
customize desired
image settings
NORMAL
:
A
:
D
:
Adjustable
Analog Input
Digital Input
NOTE
The order of icons may differ
depending
A9
on
the model (A9~A13).
On Screen
Selection and
Display(OSD)
Adjustment
procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
You
were
introduced to the
Press the MENU
Button, then the main menu of the OSD appears.
Menu Name
PICTURE
Icons
50
Sub-menus
50
0
MENU
Button
+
-
SET
Tip
MENU
:
:
Exit
Adjust (Decrease/Increase)
SET
:
Enter
:
Select another sub-menu
NOTE
OSD (On Screen
Display)
menu
languages
on
A10
the monitor may differ from the manual.
On Screen
Display(OSD)
Main
Selection and
Sub
menu
Adjustment
Description
menu
PICTURE
BRIGHTNESS
of the
BRIGHTNESS
To
adjust
the
CONTRAST
To
adjust
the contrast of the
GAMMA
Set your own gamma value. : -50/0/50
On the monitor, high gamma values
display whitish images and low gamma
values display high contrast images.
brightness
screen.
screen.
50
50
0
MENU
+
-
SET
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
COLOR
Select the screen color.
9300K: Slightly bluish white.
6500K: Slightly reddish white.
PRESET
PRESET
?
?
6500K
9300K
50
RED
Set your
own
red color levels.
GREEN
Set your
own
green color levels.
BLUE
Set your
own
blue color levels.
50
50
MENU
-
+
SET
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
POSITION
H
POSITION
H POSITION
To
move
image left
V POSITION
To
move
image
50
50
MENU
-
+
SET
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
A11
and
right.
up and down.
On Screen
Display(OSD)
Main
Selection and
Sub
menu
Adjustment
Description
menu
TRACKING
CLOCK
CLOCK
To minimize any vertical bars or stripes
visible on the screen background.The
horizontal
screen
size will also
change.
50
the focus of the display. This
item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
To
PHASE
50
MENU
+
-
SET
adjust
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
FACTORY RESET
FACTORY
FACTORY
Restore all factory default settings except
"LANGUAGE."
If you want to reset the monitor, select the YES
and then press the or + button to execute.
RESET
RESET
-
YES
NO
If the output of the video card is different the
required specifications, the color level may
deteriorate due to video signal distortion. Using
this function, the signal level is adjusted to fit
into the standard output level of the video card
in order to provide the optimal image.
Activate this function when white and black
colors are present in the screen.
WHITE
BALANCE
PRESET
MODE
ANALOG
1024
MENU
x
768
+
-
MENU
:
:
SET
:
60Hz
SET
Exit
Adjust
Adjust
:
For
Select another sub-menu
example
If this does not improve the screen image, restore the factory default settings. If necessary,
perform the white balance function again. This function will be enabled only when the input
signal is an analog signal.
If you want to adjust, select the YES and then press the or + button to execute.
-
SETUP
LANGUAGE
LANGUAGE
To choose the
control
names
language in which
are displayed.
the
ENGLISH
horizontal position of the OSD
window on the screen.
To
OSD
H POSITION
adjust
50
50
MENU
-
+
SET
vertical position of the OSD
window on the screen.
To
OSD
V POSITION
MENU : Exit
: Decrease
: Increase
SET : Select another sub-menu
A12
adjust
On Screen
Display(OSD)
The OSD
screen
Selection and
Adjustment
will appear when you press the F-ENGINE
(-)
button at the
front side of the monitor.
Menu Name
Icons
Sub-menu Name
FLATRON F-ENGINE
Screen when
Screen when not applied
applied
When you execute F-ENGINE, two tones will appear
on the screen as shown. The applied screen will
the left side, whereas the non-applied
screen will appear on the right side.Press the
SETbutton to use the adjusted screen.
on
appear
Main
Sub
menu
MOVIE
TEXT
MOVIE
Description
menu
This feature lets you easily select the best desired
image condition optimized to the environment
(ambient illumination, image types etc).
MOVIE For animation
images
in videos
or
movies
Select another sub-menu
:
TEXT For text
USER
images (Word processing etc.)
User
You
manually adjust brightness, ACE or RCM.
You can save or restore the adjusted value even
when using a different environment setting.
To
adjust the
USER sub-menu
function,
can
(Brightness): Adjusts screen brightness.
ACE(Adaptive Clarity Enhancer) Selects the clarity mode.
RCM(Real Color Management) Selects the color mode.
Press the SET Button
BRIGHTNESS
100
ACE
1
0
Not
RCM
3
1
Green enhance
2
Flesh tone
3
Color Enhance
NO
USER
MENU
MENU
+
-
applied
SET
Exit
: Decrease
: Increase
SET : Select another sub-menu
:
Select the
button and
buttons.
sub-menu
save
the SET
the YES value using the
NORMAL This is under normal
A13
using
operating
conditions.
-
Troubleshooting
Check the
No
following before calling for service.
image
appears
Is the power cord of the
display connected?
Check and
Is the power indicator
light on?
Press the Power button.
Is the power on and the
power indicator green?
Adjust the brightness
Is the power indicator
amber?
If the
properly
Try
on
the screen?
and the contrast.
is in power
saving mode, try moving
the mouse or pressing any key on the keyboard
to bring up the screen.
display
if the power is
to turn on the PC.
Make
Do you see an "OUT
OF RANGE" message
if the power cord is connected
to the power outlet.
see
sure
on.
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
Do you see a "CHECK
SIGNAL CABLE
This message appears when the signal cable
between your PC and your display is not
"message on the
connected. Check the
signal cable
and try
again.
screen?
Do you
see a
"OSD LOCKED" message
Do you see "OSD
LOCKED" when you
You
MENU button?
You
push
so
by
can secure
that
they
on
the screen?
the current control
cannot be
settings,
inadvertently changed.
unlock the OSD controls at any time
pushing the MENU button for 5 seconds.
can
The message "OSD UNLOCKED" should
appear.
A14
Troubleshooting
Display image
Display
is incorrect
Position is
incorrect.
Press the SET/AUTO button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
recommend resolution.
On the
screen
background, vertical
bars or stripes are
visible.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
The
screen
mono or
color is
abnormal.
Press the SET/AUTO button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon
the on screen display.
in
Press the SET/AUTO button to
automatically
adjust your display image to the ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
Check if the
signal cable
is
properly connected
screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
and
use a
the slot.
Set the color
setting higher than 24
color) at Control Panel Settings.
bits
(true
-
The
screen
blinks.
Check if the
screen
is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be higher than AC100-240V 50/60Hz.
A15
Troubleshooting
Have you installed the
driver?
display
Have you installed the
display driver?
display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
driver from our web site: http://www.lge.com.
Do you
Make
see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
Be
sure
to install the
sure
to check if the video card
Plug&Play function.
monitor found"
message?
A16
supports
L1730B
Specifications
Display
17 inches (43.2cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
17 inches viewable
0.26
Sync Input
mm
pixel pitch
Horizontal
Freq.
30
30
Vertical
56
Freq.
Input Form
-
-
-
83kHz
71kHz
(Analog)
(Digital)
75Hz (Automatic)
Separate TTL, Positive/Negative
SOG
(Sync On Green)
Digital
Video
Input
15
Signal Input
pin D-Sub Connector
DVI
Resolution
-
D connector
Input Form
RGB Analog (0.7Vp-p/75ohm), Digital
Max
VESA 1280
x
1024@75Hz
Recommend
VESA 1280
x
1024@60Hz
Plug&Play
DDC 2B
Power
Normal
:
Consumption
Stand-by/Suspend
≤
DPMS Off
≤2W
Dimensions
Width
39.80
&Weight
(with tilt stand)
Height
Depth
Tilt
Range
Power
Input
Environmental
Conditions
Tilt Stand
Signal
cable
Power cord
43W
2W
Net
/ 15.67 inches
40.33 cm / 15.88 inches
22.00 cm / 8.66 inches
4.90 kg (10.80 lbs)
Tilt
-5˚~30˚
cm
AC 100-240V~50/60Hz 1.0A
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Storage Conditions
Temperature -20˚C to 60 ˚C
5 % to 95 % non-Condensing
Humidity
Attached(
), Detachable ( O )
Attached(
), Detachable ( O )
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A17
notice.
FT
L1930B
Specifications
Display
19 inches (48.26cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
19 inches viewable
0.294
Sync Input
mm
pixel pitch
Horizontal
Freq.
30
30
Vertical
56
Freq.
Input Form
-
-
-
83kHz
71kHz
(Analog)
(Digital)
75Hz (Automatic)
Separate TTL, Positive/Negative
SOG
(Sync On Green)
Digital
Video
Input
15
Signal Input
pin D-Sub Connector
DVI
Resolution
-
D connector
Input Form
RGB Analog (0.7Vp-p/75ohm), Digital
Max
VESA 1280
x
1024@75Hz
Recommend
VESA 1280
x
1024@60Hz
Plug&Play
DDC 2B
Power
Normal
:
Consumption
Stand-by/Suspend
≤
DPMS Off
≤2W
Dimensions
Width
44.44
&Weight
(with tilt stand)
Height
Depth
Tilt
Range
Power
Input
45W
2W
Net
/ 17.49 inches
43.83 cm / 17.25inches
22.00 cm / 8.66inches
6.5 kg (14.33 lbs)
Tilt
-5˚~30˚
Swivel
-300˚
cm
AC 100-240V~50/60Hz 1.0A
Environmental
Conditions
Operating Conditions
Temperature 10˚C to 35 ˚C
10 % to 80 % non-Condensing
Humidity
Storage Conditions
Temperature -20˚C to 60 ˚C
5 % to 95 % non-Condensing
Humidity
Tilt Stand
Attached(
), Detachable ( O )
Attached(
), Detachable ( O )
Signal
cable
Power cord
Wall-outlet type
or
PC-outlet type
NOTE
Information in this document is
subject to change without
A18
notice.
FT
Specifications
Preset Modes
(Resolution)
17 inch monitor
Display Modes (Resolution)
123456789
10
11
12
13
VGA
VGA
VGA
VESA
VESA
VESA
MAC
VESA
VESA
MAC
VESA
VESA
VESA
Horizontal
Freq. (kHz)
Vertical
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
Freq. (Hz)
70
70
60
75
60
75
75
60
75
75
65
60
75
19 inch monitor
Display Modes (Resolution)
123456789
10
11
12
13
VGA
VGA
VGA
VESA
VESA
VESA
MAC
VESA
VESA
MAC
VESA
VESA
VESA
Horizontal
31.469
31.468
31.469
37.500
37.879
46.875
49.725
48.363
60.123
68.681
61.805
63.981
79.976
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1152 x 870
1152 x 900
1280 x 1024
1280 x 1024
Indicator
MODE
LED Color
Normal
green
Stand-by/Suspend
amber
DPMS Off
amber
Freq. (kHz)
A19
Vertical
Freq. (Hz)
70
70
60
75
60
75
75
60
75
75
65
60
75
How to Install the VESA Standard wall
This monitor meets
mounting
VESA-compliant mounting
interface
pad
specifications.
1.
Remove the
Sliding
Door and Stand Cover.
Sliding
Door
Stand Cover
2.
Please the monitor
front side
3. Separate
4.
on a
piece of cloth
downward.
the stand base using
or
other soft surface with the
facing
Install the VESA standrad wall
a
screwdriver
as
shown in the
picture.
mounting.
VESA wall
mounting
Connected to another
and wall-mounted
object (stand type
type. This monitor
VESA-compliant mounting
interface pad.-optional)
For further information, refer to the VESA
Wall Mounting Instruction Guide.
accepts
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most computer
stores
A20
a
Digitally yours
Download PDF