LG | M1721A-BT | LG M1721A-BT Owner’s Manual

User’s Guide
M1721A
M1921A
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for future reference.
See the label attached on the product and give the information to your dealer when you ask
for service.
Safety Precautions
Please read these safety precautions carefully before using the product.
Warning If you ignore the warning message, you may be seriously injured or there is a possibility of
accident or death.
Caution If you ignore the caution message, you may be slightly injured or the product may be damaged
Precautions in installing the Product
Warning
Keep away from heat sources like electrical heaters.
- Electrical shock, fire, malfunction or deformation may occur.
Keep the packing anti-moisture material or vinyl packing out of the reach of children.
- Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the patient to vomit and visit the
nearest hospital. Additionally, vinyl packing can cause suffocation. Keep it out of the reach of children.
Do not put heavy objects on the product or sit upon it.
- If the product collapses or is dropped, you may be injured. Children must pay particular attention.
Do not leave the power or signal cable unattended on the pathway.
- The passerby can falter, which can cause electrical shock, fire, product breakdown or injury.
Install the product in a neat and dry place.
- Dust or moisture can cause electrical shock, fire or product damage.
If you can smell smoke or other odors or hear a strange sound unplug the power cord and contact the
service center.
- If you continue to use without taking proper measures, electrical shock or fire can occur.
If you dropped the product or the case is broken, turn off the product and unplug the power cord.
- If you continue to use without taking proper measures, electrical shock or fire can occur. Contact the service
center.
Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the product, or inflammable
objects such as paper and matches. Children must pay particular attention.
- Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and
contact the service center.
Caution
Make sure the product ventilation hole is not blocked. Install the product in a suitably wide place (more
than 10cm from the wall)
- If you install the product too close to the wall, it may be deformed or fire can break out due to internal heat.
Do not block the ventilation hole of the product by a tablecloth or curtain.
- The product can be deformed or fire can break out due to overheating inside the product.
Install the product on a flat and stable place that has no risk of dropping the product.
- If the product is dropped, you may be injured or the product may be broken.
Install the product where no EMI occurs.
Keep the product away from direct sunlight.
- The product can be damaged.
1
Safety Precautions
Electrical Power Related Precautions
Warning
Make sure to connect the power cable to the grounded current.
- You may be electrocuted or injured.
Use the rated voltage only.
- The product can be damaged, or you may be electrocuted.
During a thunder or lightning storm, unplug the power cable or signal cable.
- You may be electrocuted or a fire can break out.
Do not connect several extension cords, electrical appliances or electrical heaters to a single outlet.
Use a power bar with a grounding terminal designed for exclusive use with the computer.
- A fire can break out due to overheating.
Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or covered with dust, dry
the power plug completely or wipe dust off.
- You may be electrocuted due to excess moisture.
If you don’t intend to use the product for a long time, unplug the power cable from the product.
- Covering dust can cause a fire, or insulation deterioration can cause electric leakage, electric shock or fire.
Fix the power cable completely.
- If the power cable is not fixed completely, a fire can break out.
Hold the plug when pulling out the power cable. Do not bend the power cord with excessive force or put
heavy objects on the power cord.
- The power line can be damaged, which may cause electric shock or fire.
Do not insert a conductor (like a metal chopstick) into one end of the power cable while the other end is
connected to the input terminal on the wall. Additionally, do not touch the power cable right after
plugging into the wall input terminal.
- You may be electrocuted.
The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily
accessible after installation.
Caution
Do not unplug the power cord while the product is in use.
- Electrical shock can damage the product.
Precautions in Moving the Product
Warning
Make sure to turn off the product.
- You may be electrocuted or the product can be damaged.
Make sure to remove all cables before moving the product.
- You may be electrocuted or the product can be damaged.
2
Safety Precautions
Caution
Do not shock the product when moving it.
- You may be electrocuted or the product can be damaged.
Do not dispose the product-packing box. Use it when you move.
Make the panel face forward and hold it with both hands to move.
- If you drop the product, the damaged product can cause electric shock or fire. Contact with the service center
for repair.
Precautions in Using the Product
Warning
Do not disassemble, repair or modify the product at your own discretion.
- Fire or electric shock accident can occur.
- Contact the service center for check, calibration or repair.
When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent
scratching. Do not clean with a wet cloth.
Keep the product away from water.
- Fire or electric shock accident can occur.
Caution
Do not put or store inflammable substances near the product.
- There is a danger of explosion or fire due to careless handling of the inflammable substances.
When cleaning the brown tube surface, unplug the power cord and scrub with soft cloth to prevent
scratching. Do not clean with a wet cloth.
- The water can sink into the product, which can cause electric shock or serious malfunction.
Take a rest from time to time to protect your vision.
Keep the product clean at all times.
Take a comfortable and natural position when working with a product to relax the muscles.
Take a regular break when working with a product for a long time.
Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make
a scratch on it.
Keep the proper distance from the product.
- Your vision may be impaired if you look at the product too closely.
Set the appropriate resolution and clock by referring to the User’s Guide.
- Your vision can be impaired.
Use authorized detergent only when cleaning the product. (Do not use benzene, thinner or alcohol.)
- Product can be deformed.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.
Disposal of this product must be carried out in accordance to the regulations of your local authority.
3
Before Connecting to the PC
Connecting the stand
Before setting up the product, ensure that the power supply, the computer system,
and other attached devices is turned off.
1. Place the monitor with its front facing downward on a soft cloth.
2. Connect the Stand Base to the Stand Body and press latches at the button toward each end.
3. Connect the Stand, assembled in step 2, to the Monitor Panel until you hear a "Click".
4. Once assembled take the monitor up carefully and face the front side
2.
Stand Body
Stand Base
3.
Stand
Slot
Important
Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only the stand base. The product may
fall and get damaged or injure your foot.
4
Before Connecting to the PC
Before setting up the product, ensure that the power supply, the computer system,
and other attached devices is turned off.
Positioning your display
1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~15˚
Swivel :320˚
Warning:
When adjusting the angle of the screen, do not put
your finger(s) in between the head of the monitor and
the stand body. You can hurt your finger(s).
Theft prevention locking device
Locking Device
Use this locking cable (This has to be purchased
separately if required.) to prevent theft.
5
Name and Function of the Parts
Name of the Remote Control Buttons
POWER
TV
MUTE
PSM
INPUT
SSM
I/II
TV : TV button
POWER
INPUT
Input
TV
AV
Component
RGB
Each time you press the Input button it will
change to
TV
AV
Component
RGB
If nothing is inputted for several seconds the
screen will automatically move to the
selected menu.
OK
LIST
Q.VIEW
MUTE
Switches the sound on or off.
PR
PSM (Picture Status Memory) Button
OK
VOL
VOL
SSM (Sound Status Memory) Button
Use this button to select the sound tone.
PR
MENU
SLEEP
Press repeatedly to select Dynamic, Standard, Mild, Game or User
picture mode.
ARC/*
*
Press repeatedly to select Flat, Music, Movie, Sports, User sound tone.
Number buttons
Able to directly select and change channel.
NOTE : In case of weak stereo sound signals, with stereo or Nicam stereo
transmission, select mono reception.
Inserting batteries into remote control.
1. Take out the battery cap.
2. Insert the batteries with correct polarity (+/-).
3. Close the battery cap.
• Dispose of used batteries in the recycle bin to prevent
environmental pollution.
6
Name and Function of the Parts
Name of the Remote Control Buttons
POWER
TV
INPUT
I/II : Bilingual choice and sound mode selection
[TV]
MUTE
PSM
SSM
I/II
To switch from Stereo to Mono sound in case of stereo transmission,
or from Nicam Stereo to Nicam Mono, in case of digital transmission.
to switch from Nicam Dual I to Nicam Dual II or Nicam Dual I+II in
case of Nicam Dual transmission.
to choose between Dual I, Dual II or Dual I+II in case of bilingual
transmission :
Dual I sends the primary broadcast language to the loudspeakers ;
Dual II sends the secondary broadcast language to the loudspeakers ;
Dual I+II sends a separate language to each loudspeakers.
[AV]
LIST
Q.VIEW
PR
OK
VOL
VOL
PR
MENU
SLEEP
ARC/*
*
In AV/Component mode, you can select output sound for the left and
right loudspeakers. Repeatedly press the I/II button to select the sound output.
L+R : Audio signal from audio L input is sent to left
loud-speaker and audio signal from audio R input is
sent to right loud-speaker.
L+L : Audio signal from audio L input is sent to left and right loud-speakers.
R+R : Audio signal from audio R input is sent to left and
right loud-speakers.
LIST : Programme list
To display the programme list (0~ 99).
Programme List
0
1
2
3
4
C
C
C
C
C
01
35
05
11
04
5
6
7
8
9
C
C
C
C
C
07
50
51
41
63
OK MENU
Note: TV channels displayed in blue have been setup
to be skipped in the Programme Edit menu.
Q.VIEW : QUICK VIEW Button
To display the previously selected TV channel
7
Name and Function of the Parts
Name of the Remote Control Buttons
PR
OK
VOL
VOL
PR
MENU
SLEEP
ARC/*
*
PR (
) Buttons
Able to change channel.
VOL (
) Buttons
Able to adjust sound.
OK Button
Use when functional adjustment is completed.
MENU
Use this button to enter the On Screen Display menu.
SLEEP : SLEEP Timer
You can set a time period after which the
TV / AV / Component / RGB should switch itself to standby. Press
the key repeatedly to select the number of minutes.
_ _ _ (off)
240
ARC
No function
8
10
20
30
180
120
90
60
Name and Function of the Parts
Remote Control - Using the Teletext function
(Depends on the country the remote control can be provided different.)
TEXT
LIST
To select the teletext on or off. The main index
page or the last selected page appears on the
screen together with an information headline and
an option line at the bottom of the screen.
Q.VIEW
PR
OK
VOL
VOL
Yellow key
Favourite Program On : Rotate favourite channel
PR
SLEEP
MENU
Favourite Program Off : To display the previously
selected TV channel.
ARC/*
TEXT
HOLD
HOLD
REVEAL
MIX
SIZE
?
INDEX
i
MODE
TIME
M
UPDATE
X
Press the button to stop the automatically rotating
of the sub pages. Press the button again to
continue the automatic rotating again.
SIZE
Press the button repeatedly to display the upper
part, the lower part and then to return to the
normal page size.
MIX
Display the teletext pages superimposed on
the TV picture. To switch the TV picture off
press this button again.
TIME
Press this button to select a sub page number.
The sub page number is displayed at the
bottom of the screen. To hold or change the
sub page, press the RED/GREEN,
or
NUMBER buttons. Press again to exit this
function.
9
Name and Function of the Parts
Remote Control - Using the Teletext function
REVEAL
PR
OK
VOL
Press the button to reveal/conceal the hidden
information, such as solutions to riddles and
puzzles. Press this button again to remove the
information from the display.
VOL
PR
INDEX
SLEEP
MENU
ARC/*
TEXT
To display the main index.
MODE
HOLD
REVEAL
MIX
SIZE
?
INDEX
i
MODE
TIME
M
UPDATE
The mode will be switched in the Teletext mode.
X
UPDATE
Press the button to appear the TV programme.
At the top of screen indicates that you are still in the
teletext mode. Before interrupting teletext, you may
select a page number. When the page has been
found, the information line appears briefly on your
screen. Press the button again to reappear teletext.
10
Name and Function of the Parts
Rear View
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
PB
Y
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
H/P
AV IN
[19 inch]
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
PB
Y
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
H/P
AV IN
[17 inch]
AUDIO
(RGB) IN ANTENNA IN
RGB (PC/DTV) IN
VIDEO
Y
PB
AUDIO
PR
L
COMPONENT IN
R
L (Mono)
VIDEO
R
AUDIO
S-VIDEO
H/P
AV IN
Power Connector : Connect the power cord.
Component Input Terminal
D-Sub Analog Signal Connector
RGB Sound Jack : Connect to the jack in the PC sound card or D-TV sound Output Jack.
TV Tuner Jack : Connect the antenna.
AV Input Terminal
Headphone/Earphone Connection Terminal
11
Name and Function of the Parts
AV Input Terminal
(RGB) IN
[19 inch]
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
AV IN
[17 inch]
L (Mono)
VIDEO
R
AUDIO
S-VIDEO
AV IN
Video Input Terminal
Audio Input Terminal
S-Video Input Terminal
12
Connecting to External Devices
Connecting to your PC
1.
First of all, see if the computer, product and the peripherals are turned off.
Then, connect the signal input cable.
Rear side of the product.
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
Y
PB
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
H/P
AV IN
Connecting with the D-Sub signal input cable.
RGB (PC/DTV) IN
Rear side of the product.
Macintosh Adapter (Not included)
Use the standard Macintosh adapter since an incompatible
adapter is available in the market. (Different signaling system)
2.
Connect the audio cable.
AUDIO
(RGB) IN
Audio cable
Rear side of the product.
• Make sure to check the sound card connection terminal in the PC before connecting to the product.
If the PC sound card supports both Speaker Out and Line Out, change it to Line Out by setting the jumper
or the PC application. (For more details, refer to the sound card user’s guide.)
- Speaker Out : The terminal connected to the speaker that is not equipped with an amplifier.
- *Line Out : The terminal connected to the speaker equipped with an amplifier.
If Audio Out in the PC sound card has only Speaker Out, reduce the PC volume. This product is integrated
with an amplifier.
13
Connecting to External Devices
3.
Connect the power cord.
Rear side of the product.
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
Y
PB
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
H/P
AV IN
4. 1
Turn on power by pressing the power button on the product.
INPUT MENU
OK
VOL
PR
Power button
2 Turn on the PC.
5.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
OK
Or, press the INPUT button at the top side of the product.
INPUT
OK
• Select RGB
Input
TV
AV
Component
RGB
OK
Each time you press the Input button it will change to TV
AV
Component
RGB
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
Note
• Directly connect to a grounded power outlet on the wall or a power bar with a ground wire.
14
Connecting to External Devices
Connecting to VCR/DVD
1.
Connect the video/audio cable as shown in the figure below and then connect the power
cord (See page 14).
A When using the RCA cable.
B When using the S-Video cable.
• Connect the input terminal with a
• Connect to the S-Video input terminal to
watch high image quality movies.
proper colour match.
Rear side of the Product
Rear side of the Product
[19 inch]
(RGB) IN
VIDEO
VIDEO
L
(Mono)
AUDIO
L
(Mono)
AUDIO
R
VIDEO
S-VIDEO
L
(Mono)
AV IN
R
AUDIO
R
S-VIDEO
AV IN
S-VIDEO
AV IN
[17 inch]
L (Mono)
VIDEO
R
S-Video
Cable
(Not
included)
AUDIO
S-VIDEO
AV IN
RCA Cable
(Not included)
RCA
Cable
(Not
included)
VIDEO
OUT
AUDIO
OUT
VCR/DVD
VCR/DVD
Note
AUDIO
OUT
VIDEO
OUT
• In case the RCA cable is connected simultaneously as S-Video cable is connected, S-Video cable is first.
15
Connecting to External Devices
2.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
OK
Or, press the INPUT button at the topside of the product.
INPUT
OK
A
When connecting with a RCA cable.
• Select AV
B
When connecting with a S-Video cable.
Input
TV
AV
Component
RGB
• Select AV
OK
Each time you press the Input button it will change to TV
AV
Component
RGB
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
16
Connecting to External Devices
Connecting to Set-top Box /DVD (480i/576i/480p/576p/720p/1080i)
1.
Connect the video/audio cable as shown in the figure below and then connect the power
cord (See page 14).
• Connect the input terminal with a proper color match.
Rear side of the Product
[19 inch]
COMPONENT IN
VIDEO
COMPONENT IN
AUDIO
VIDEO
PB
Y
PR
L
R
Y
PB
AUDIO
PR
L
R
[17 inch]
VIDEO
Y
Component Cable
Audio Cable
(Not included)
(Not included)
Pb
Y
Pr
L
PB
AUDIO
PR
L
R
COMPONENT IN
R
VIDEO
AUDIO
COMPONENT OUT
2.
Set-top Box /DVD
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
OK
Or, press the INPUT button at the top side of the product.
INPUT
Input
TV
AV
Component
RGB
OK
• Select Component
MENU
Each time you press the Input button it will change to TV
AV
Component
RGB
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
17
Connecting to External Devices
Connecting to DVD/SET-TOP BOX
1.
Connect the D-sub cable, RCA/PC cable as shown in the below figure
and then connect the power cord. (see page 14)
[Rear side of the Product]
[19 inch]
[17 inch]
AUDIO
(RGB) IN A
RGB PC/DTV IN
AUDIO
(RGB) IN
AUDIO
(RGB) IN
RCA-Stereo cable
(not included)
D-Sub cable
[Set-top Box/DVD]
2.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
OK
Or, press the INPUT button at the topside of the product.
INPUT
OK
• Select RGB
Input
TV
AV
Component
RGB
OK
Each time you press the Input button it will change to TV
AV
Component
RGB
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
18
Connecting to External Devices
When Watching TV
1.
Check if the antenna cable is connected at the rear side of the product
and then, connect the power cord.
Rear Side of the Product
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
PB
Y
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
H/P
AV IN
ANTENNA IN
Antenna Cable
(Not included.)
2.
Select an input signal.
Press the INPUT button on the remote control to select the input signal.
INPUT
OK
Or, press the INPUT button at the top side of the product.
INPUT
• Select TV
OK
Input
TV
AV
Component
RGB
OK
Each time you press the Input button it will change to TV
AV
Component
RGB
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
19
To arrange cables using cable management
1.
Arrange the cables in the center as shown in the following picture.
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
AUDIO
PB
Y
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
H/P
AV IN
2.
Fit the cable management to the Holder Groove downwards.
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
ANTENNA IN
RGB (PC/DTV) IN
VIDEO
COMPONENT IN
VIDEO
Y
PB
AUDIO
PR
L
Y
AUDIO
(RGB) IN
R
PB
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
AV IN
H/P
AV IN
cable
management
Hold the cable management and lift up slightly to remove it.
Warning
• Do not use the cable management as a handle for the Monitor.
• Do not press the cable management.
20
H/P
Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
Y
PB
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
(Mono)
AUDIO
R
S-VIDEO
H/P
AV IN
INPUT MENU
OK
Power Indicator
Power Button
MENU Button
OSD Select/Adjust Button
VOL
PR
• This Indicator lights up green when the display operates normally
(On Mode). If the display is in Sleep (Energy Saving) Mode, this
indicator colour changes to red.
• Use this button to turn the product on and off.
• Use this button to show/hide the OSD (On Screen Display) menu
screen.
• Use this button to select an icon or adjust the setting in the OSD screen.
• Use this button to control the channel for the TV signal.
• Adjust the volume.
21
Volume
30
Adjusting the Screen
Name of the Buttons in the Screen Adjustment Unit
OK Button
INPUT Button
• OK button is usually used in choosing the MENU.
When there is no MENU on the screen pushing the OK button will
give the information about the current input source.
Input
TV
AV
Component
RGB
Television
CVBS, S-Video
HDTV, DVD
D-Sub analog signal
TV
AV
Component
RGB
OK
Each time you press the Input button it will change to TV
AV
Component
RGB
If nothing is inputted for several seconds the screen will automatically move to the selected menu.
IR Receiver
• The unit that receives the signal from the remote control.
22
Adjusting the Screen
OSD (On Screen Display) Menu
Icon
Function Description
Set/Select the channel when using the TV
Station
Adjusting the picture function.
Picture
Adjusting the sound function.
Sound
Adjusting the time function.
Time
Selecting the special function.
Special
Adjusting the screen function.
Screen
Note
OSD(On Screen Display)
The OSD function enables you to adjust the screen status conveniently since it provides
graphical presentation.
23
Adjusting the Screen
OSD (On Screen Display) Screen Tracking Order
PR
PR
MENU
VOL
OK
VOL
VOL
OK
VOL
OK
MENU
PR
PR
Pop up the
menu screen
OK
Move where
you want to
adjust
Select a menu icon
Adjust the status
Save
adjustment
Exit from the
menu screen.
• Use the remote control to adjust the OSD screen.
1
Press the MENU Button, then the main menu of the OSD will appear.
2
To access a control, use the
3
When the icon you want becomes highlighted, press the OK Button.
4
Use the
5
Accept the changes by pressing the OK Button.
6
Exit the OSD by pressing the MENU Button repeatedly .
Buttons.
Buttons to adjust the item to the desired level.
24
Adjusting the Screen
STATION ID set/Select the channel when using the TV
Auto programme
Station
Auto programme
Manual programme
Programme edit
Favourite programme
To set
OK MENU
System
It should be set before run auto searching.
Press the
buttons to select the TV system of the country or part of the
world from where you want to receive the TV channels.
* Supporting channel : C(V/UHF 02~69) S(Cable 01~41)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I : PAL I/II (U.K/Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
M : NTSC M
Storage
from
To select a programme number or enter the programe number with the
number buttons from where you want to start searching for new channels.
If e.g. you want to keep the channels 1 to 10 stored earlier, enter programe
number 11. Your TV search for new channels from number 11 onwards.
* Numbers available to store : 0~99
Search
Press OK or
button to start automatic programming. All available TV
channels will be searched and stored automatically. To stop auto
programming, press the MENU button. When auto programming is
completed, the programme list menu appears.
Manual programme
Station
Auto programme
Manual programme
Programme edit
Favourite programme
To set
To change the channel.
(Change each item in Manual
Program and press the "MENU"
button to save the settings)
OK MENU
Storage
Press the
buttons to select the channel number or enter the
programme number with the number buttons in where you want to store
channel.
System
Press the
buttons to select the TV system of the country or part of
the world from where you want to receive the TV channels.
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I : PAL I/II (U.K/Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
M : NTSC M
25
Adjusting the Screen
STATION ID set/Select the channel when using the TV
Press the
buttons to select VHF/UHF for aerial channels or Cable for
cable channels.
To select the channel reception type. : VHF/UHF / Cable.
Band
Channel If you know the channel number, enter it directly with the digit buttons 0 to 9.
Fine
In case of poor reception, you can improve the reception by fine tuning. Use
the
buttons to fine tune for the best picture and sound.
Search
Use the
Name
To see the assigned channel name.
It is possible to change the name stored in the memory or to assign a name
to a TV channel which has not yet been entered. A name with up 5 letters or
numbers can be given to the programme numbers 0 to 99.
buttons to search next channel backward or forward direction.
Press the
buttons to move cursor to be changed. -> Press the
buttons to select a character.(space, number 0~9, and alphabet A~Z, +,-) ->
Press OK button or MENU button.
Programme edit
Programme edit
Station
Auto programme
Manual programme
Programme edit
Favourite programme
To set
0
1
2
3
4
C
C
C
C
C
01
35
05
11
04
Delete
Move
5
6
7
8
9
C
C
C
C
C
07
50
51
41
63
Copy
Skip
OK MENU
OK MENU
Delete
Press the
buttons to select a TV channel to be deleted. ->
Press the red key on the remote control -> The background colour of
the selected channel will change to red.
Press the Delete button one more time to delete the selected channel.
All the following channels are shifted up one position.
Copy
Press the
buttons to select a TV channel to be copied. ->
Press the green key on the remote control. All the following channel
numbers are shifted down one position.
Move
Press the
buttons to select a channel number to be moved. ->
Press the yellow key on the remote control. -> Press the
buttons to move the TV channel to the desired channel number. ->
Press the yellow key again to release this function.
Skip
Press the
buttons to select a channel number to be skipped. ->
Press the blue key on the remote control. The skipped TV channel is
displayed in blue.
26
Adjusting the Screen
STATION ID set/Select the channel when using the TV
Favourite
programme
Station
Auto programme
Manual programme
Programme edit
Favourite programme
Off
__
__
__
__
__
__
__
__
_____
_____
_____
_____
_____
_____
_____
_____
OK MENU
This function lets you select your favourite programmes directly. (8 channel)
Press the
buttons to select a channel.
* Yellow key (remote control) :
Favourite Program On : Rotate favourite channel
Favourite Program Off : To display the previously selected TV channel.
27
Adjusting the Screen
PICTURE ID adjust the picture function (RGB-PC)
PSM
<
Picture
PSM
CSM
Reset
Dynamic
Standard
Mild
Game
User
OK MENU
The PSM function automatically adjusts the screen
image quality. (It is not working in PC input.)
• Dynamic
Select this option to display with a sharp image.
• Standard
The most general and natural screen display status.
• Mild
Select this option to display with a mild image.
• Game
Select this option to enjoy dynamic image when
playing a game.
• User
Select this option to use the user-defined settings.
CSM
Picture
<
PSM
CSM
Reset
OK MENU
Reset
9300K
6500K
sRGB
User
Selecting a factory setting colour set.
• 9300K
Slightly purplish white.
• 6500K
Slightly bluish white.
• sRGB
Slightly lower brightness.
• User
Select this option to use the user-defined settings.
Red / Green / Blue
Set your own colour levels.
Return to the default settings PSM, CSM at the factory.
28
Adjusting the Screen
PICTURE ID adjust the picture function (TV/AV/Component/RGB-DTV)
PSM
<
Picture
PSM
CSM
Reset
Dynamic
Standard
Mild
Game
User
OK MENU
CSM
Picture
<
PSM
CSM
Reset
Cool
Normal
Warm
User
The PSM function automatically adjusts the screen
image quality.
• Dynamic
Select this option to display with a sharp image.
• Standard
The most general and natural screen display status.
• Mild
Select this option to display with a mild image.
• Game
Select this option to enjoy dynamic image when
playing a game.
• User
Select this option to use the user-defined settings.
Selecting a factory setting colour set.
• Cool
Slightly purplish white.
• Normal
Slightly bluish white.
• Warm
Slightly reddish white.
• User
Select this option to use the user-defined settings.
Red / Green / Blue
Set your own colour levels.
OK MENU
Reset
Return to the default settings PSM, CSM at the factory.
OK MENU
29
Adjusting the Screen
SOUND ID to adjust the sound function
SSM
AVL
Balance
<
Sound
0
Flat
Music
Movie
Sports
User
OK MENU
SSM
The best sound tone quality will be selected automatically depending on the video type that
you're currently watching.
• Flat : The most commanding and natural audio.
• Music : Select this option to enjoy the original sound when listening to the music.
• Movie : Select this option to enjoy sublime sound.
• Sports : Select this option to watch sports broadcasting.
• User : Select this option to use the user-defined audio settings.
AVL
To adjust uneven sound volumes across all channels or signals automatically to the most
appropriate level. To use this feature, select On.
Balance
Use this function to balance sound from the left and right speakers.
30
Adjusting the Screen
TIME ID to adjust the time function
Time
Clock
Off time
On time
Auto sleep
-- : --
OK MENU
Clock
This function is used to set up of current time.
You must set the time correctly before using On/Off time function.
1) Press the MENU button and then use
button to select the Time menu.
2) Press the
button and then use
button to select the Clock menu.
button and then use
button to set the hour(00~23).
3) Press
4) Press
button and then use
button to set the minutes(00~59).
The default value is -- : --.
5) Press the OK/MENU button to save.
Off/On time
The Off time automatically switches the set to off mode at the pre-set time.
1) Press the MENU button and then use
button to select the Time menu.
2) Press the
button and then use
button to select Off time or On time.
3) Press the
button and then use
button to set the hour(00~23).
4) Press the
button and then use
button to set the minutes(00~59).
5) Press the
button and then use
button to select On or Off.
6) Only On time function; Press the
button and then
button to adjust volume level
and programme number.
7) Press the OK/MENU button to save.
Auto sleep
If Auto sleep is active and there is no input signal, the set switches to off mode
automatically after 10 minutes. ( It is not working in PC)
button to select the Auto sleep menu.
1) Press the MENU button and then use
2) Press the
button and then use
button to select On or Off.
3) Press the OK/MENU button to save .
Note
• In the event of power interruption (disconnection or power failure), the Clock must be reset.
• Two hours after the set is switched on by the On time function it will automatically switch
back to off mode unless a button has been pressed.
• Once the On or Off time is set, these functions operate daily at the preset time.
• Off time function overrides On time function if they are set to the same time.
• The set must be in off mode for the On time to work.
• On time will move on to auto off if no activity is received in 2hours after setting the On time.
• If the monitor switches to sleep mode when using the PC, "Clock" menu does not operate.
31
Adjusting the Screen
SPECIAL ID to Select the special function
Special
Language
Child lock
DDC-CI
OK MENU
Language
To choose the language in which the control names are displayed.
Child lock
Use the
buttons to select On or Off. It can be set up so that it can only be used with
the remote control. This feature can prevent unauthorized viewing.
In order to lock the OSD screen adjustment, set the Child lock tab to the 'On' position.
In order to unlock it, do the following :
* Push the MENU button on the remote control and set Child lock to the 'Off' position.
DDC-CI
DDC/CI(Display Data Channel Command Interface) is communication protocol for
communications between PC and monitor.
DDC/CI makes it possible to adjust and setup detailed functions on PC instead of the monitor
OSD.
Monitor can be adjusted with PC by connecting communication between PC and monitor when
DDC/CI is ON, and monitor cannot be adjusted with PC because communication between PC
and monitor is disconnected when DDC/CI is OFF.
32
Adjusting the Screen
SCREEN ID to adjust the screen function (only Component/RGB)
Screen
Auto config.
Manual config.
Reset
To set
OK MENU
Auto
config.
This button is for the automatic adjustment of the screen Position, Clock and Phase.
(It is not working in RGB-DTV)
Manual
config.
This button is for the manual adjustment of the screen Position, Clock and Phase.
• H-Position
To move the displayed image left or right.
• V-Position
To move the displayed image up or down.
• Clock (It is not working In RGB-DTV mode.)
To minimize any vertical bars or stripes visible on the screen background.
The horizontal screen size will also change.
• Phase (It is not working In RGB-DTV mode.)
To adjust the focus of the display. This item allows you to remove any horizontal noise
and clear or sharpen the image of characters.
Reset
Use this function to reset the product to the factory default. However, language selection
will not be initialized.
33
Troubleshooting
No image is displayed
● Is the product's power cord
connected?
• Check if the power cord is properly connected to
the outlet.
● Is the power indicator turning on?
• See if the power switch is turned on.
● Power is on, power indicator is
green but the screen appears
extremely dark.
• Adjust brightness and contrast again.
● Does the power indicator look red?
• If the product is in power saving mode, move the
mouse or press any key.
● Does the 'Out of range' message
appear?
• The signal from the PC (video card) is out of the
vertical or horizontal frequency range of the
product. Adjust the frequency range by referring to
the Specifications in this user's guide.
* Maximum resolution
17 inch : 1280 x 1024 @60Hz
19 inch : 1280 x 1024 @60Hz
● Does the 'Check signal cable'
message appear?
• The signal cable between PC and product is not
connected. Check the signal cable.
• Press the 'INPUT' button in the remote control to
check the input signal.
'Unknown Product' message appears when the product is connected.
● Did you install the driver?
• Install the product driver, which is provided with
the product, or download it from the web site.
(http://www.lge.com)
• See if the plug&play function is supported by
referring to the video card user's guide.
Note
* Vertical frequency: To enable the user to watch the product display, screen image should be changed tens of times
every second like a fluorescent lamp. The vertical frequency or refresh rate is the times of image display per second.
The unit is Hz.
* Horizontal frequency: The horizontal interval is the time to display one vertical line. When the 1 is divided by
horizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontal
frequency. The unit is kHz.
34
Troubleshooting
The screen image looks abnormal.
● Is the screen position wrong?
• Adjust the Position menu in OSD .
• See if the video card resolution and frequency
are supported by the product. If the frequency is
out of range, set to the recommended resolution
in the Control Panel – Display – Setting menu.
● Do thin lines appear on the
background screen?
• Adjust the Clock menu in OSD.
● Horizontal noise appears or the
characters look blurred.
• Adjust the Phase menu in OSD.
After-image appears on the product.
● After-image appears when the
product is turned off.
• If you use a fixed image for a long time, the pixels
may be damaged quickly. Use the screen saver
function.
35
Troubleshooting
The audio function does not work.
● No sound?
• Check if the audio cable is connected properly.
• Adjust the volume.
• Check if the sound is set properly.
● Sound is too low.
• Adjust the volume.
The TV function does not work.
● The TV signal is not being received.
• See if you have selected the proper channel
mode.
• Use the automatic channel setup function.
• Check if the TV antenna is properly connected.
Screen colour is abnormal.
● Screen has poor colour resolution (16
colours).
• Set the colour resolution to more than 24 bits (true
colour)
Select Control Panel – Display – Settings
– Colour Table menu in Windows.
● Screen colour is unstable or monocolour.
• Check the connection status of the signal cable.
Or, re-insert the PC video card.
● Do black spots appear on the screen?
• Several pixels (red, green, white or black colour)
may appear on the screen, which can be
attributable to the unique characteristics of the
LCD panel. It is not a malfunction of the LCD.
36
Specifications
The product specifications can change without prior notice for product improvement.
[17 inch]
LCD Panel
Video Signal
Screen Type
Pixel Pitch
17 inches (43.27 cm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size: 43.27 cm
0.264 mm
Max. Resolution
1280 X 1024 @60 Hz
Recommended Resolution 1280 X 1024 @60 Hz
Horizontal Frequency
30 - 70 kHz
Vertical Frequency
56 - 75 Hz
Synchronization Type Separate
Input Connector
S-Video, Composite video, TV, D-Sub Analog,
PC Audio In, Headphone/Earphone
Power
Rated Voltage
Power Consumption
AC 100-240V~ 50/60Hz 1.0A
On Mode
: 45 W
Sleep Mode ≤ 1 W
Off Mode
≤ 1W
Tilt
Tilt Range
Swivel
-5˚ ~ 15˚
320˚
Dimension/Weight
Size (WxLxH)
394.4 mm x 243.0 mmx 404 mm
Weight (excl. package) 4.5 kg (9.92 Ibs)
Environmental Conditions Operational Condition Temperature: 10˚C ~ 35˚C , Humidity: 20% ~ 80%
Storage Condition
Temperature: -10˚C ~ 60˚C , Humidity: 5% ~ 90%
37
Specifications
The product specifications can change without prior notice for product improvement.
[19 inch]
LCD Panel
Video Signal
Screen Type
Pixel Pitch
19 inches (48.19 cm) TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Panel
Visible diagonal size: 48.19 cm
0.294 mm
Max. Resolution
1280 X 1024 @60 Hz
Recommended Resolution 1280 X 1024 @60 Hz
Horizontal Frequency
30 - 70 kHz
Vertical Frequency
56 - 75 Hz
Synchronization Type Separate
Input Connector
S-Video, Composite video, TV, D-Sub Analog
PC Audio In, Headphone/Earphone
Power
Rated Voltage
Power Consumption
AC 100-240V~ 50/60Hz 1.0A
On Mode
: 45 W
Sleep Mode ≤ 1 W
Off Mode
≤ 1W
Tilt
Tilt Range
Swivel
-5˚ ~ 15˚
320˚
Dimension/Weight
Size (WxLxH)
445.0 mm x 243.0 mm x 457.0 mm
Weight (excl. package) 5.5 kg (12.13 Ibs)
Environmental Conditions Operational Condition Temperature: 10˚C ~ 35˚C , Humidity: 20% ~ 80%
Storage Condition
Temperature: -10˚C ~ 60˚C , Humidity: 5% ~ 90%
38
Specifications
PC Mode – Preset Mode
[17 inch] [19 inch]
Preset mode
1
2
3
4
5
6
7
VGA
VGA
VGA
VESA
VESA
VESA
MAC
640 x 350
720 x 400
640 x 480
640 x 480
800 x 600
800 x 600
832 x 624
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
31.469
31.468
31.469
37.500
37.879
46.875
49.725
70
70
59
75
60
75
74
Preset mode
8
9
10
11
12
Power Indicator
Mode
On Mode
Sleep Mode
Off Mode
Product
Green
Red
Off
DTV -Timming
Preset mode
*1
2
3
*4
*5
6
7
8
720 x 480/60p
720 x 576/50p
1280 x 720/50p
1280 x 720/60p
1280 x 720/60p
1920 x 1080/50i
1920 x 1080/60i
1920 x 1080/60i
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
31.47
31.25
37.5
44.955
45
28.125
33.716
33.750
59.941
50
50
59.940
60
50
59.940
60
* : User have to select directness PC or DTV
when using the PC or the Set-top box this resolution.
39
VESA 1024 x 768
VESA 1024 x 768
MAC 1152 x 870
VESA 1152 x 900
VESA 1280 x 1024
Horizontal Vertical
Frequency Frequency
(kHz)
(Hz)
48.363
60.123
68.681
61.805
63.981
60
75
75
65
60
Specifications
VESA wall mounting
This product meets VESA-compliant mounting interface pad specifications.
1. Put the product on a piece of cloth or other soft surface with the front side facing downward.
2. Pullout the stand as shown in the picture.
3. Fasten the screw on the backside of the product and the other one in the joint of the stand.
4. Install the VESA standard wall mounting.
VESA wall mounting
Connected to another
object (stand type and wallmounted type).
This product accepts a
VESA-compliant mounting
interfacepad.
(This has to be purchased
separately if required.)
For further information,
refer to the VESA Wall
Mounting Instruction Guide.
ANTENNA IN
RGB (PC/DTV) IN
COMPONENT IN
VIDEO
Y
PB
AUDIO
PR
L
AUDIO
(RGB) IN
R
VIDEO
L
AUDIO
R
40
Download PDF