DVD PLAYER/ VIDEO CASSETTE RECORDER OWNER'S MANUAL MODEL : DC577X PAL BZ03 Before please read completely. Internet adjusting this product, booklet carefully and connecting, operating this instruction or Address:http://www.lg.ru »IUO I‡?EOII‡ˇ OIUE・‡ LG Electronics (095)771-76-76 protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE 'STANDARD DEFINITION' OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. SERIAL NUMBER: The serial number is found on the back of this unit. This number is unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Model No. Serial No. SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. a of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will WARNING: TO REDUCE THE RISK OF FIRE OR ELEC- WARNING: Do not install this equipment in such as a book case or similar unit. ___________________________________ Disposal product. TRIC ___________________________________ confined space help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. CAUTION: This Digital Video Disc Player employs a Laser System. To ensure proper use of this product, please read this owner 's manual carefully and retain for future reference, should the unit require maintenance, contact an authorized service locationsee service procedure. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. CAUTION: The apparatus shall not be exposed to water, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. notes on Important This unit uses one set of controls to copyrights: following buttons are helpful successfully controlling each part. 1. front 2. 2 in POWER Button Press the POWER button panel to turn on the remote control or this unit. on DVD Button the remote control when you want to control the DVD. on The DVD indicator will display 3. It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyright material without permission. This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright operate both DVD and VCR. The This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE 89/336/EEC, 93/68/EEC and 73/23/EEC. on this unit Press DVD button Notes controlling light on the front to show that the DVD is selected. VCR Button Press the VCR button on the remote control when you want to control the VCR. The VCR indicator will light on the front display 4. panel panel to show that the VCR is selected. DVD/VCR Button Press the DVD/VCR button toggle on the front panel control between the DVD and the VCR. to Contents PlayingaDVDorVideoCD...............27-29 Introduction...................4 SymbolUsedinthisManual...............4 AbouttheSymbolDisplay..............4 NotesonDiscs..........................4 HandlingDiscs........................4 StoringDiscs.........................4 CleaningDiscs........................4 TypesofPlayableDiscs...................5 Regionalcode..........................5 Disc-relatedterms.......................6 FrontPanel.............................7 DisplayWindow.........................7 RemoteControl.........................8 RearPanel.............................9 GeneralFeatures.......................27 MovingtoanotherTITLE...............27 .27 Moving to another CHAPTER/TRACK . . . . . Search.............................27 .27 ChangingtheAudioChannel Still Picture and Frame-by-Frame Playback .28 SlowMotion.........................28 Random............................28 . . . . . . . . . . . . RepeatA-B..........................28 Repeat.............................28 3DSurround.........................28 TimeSearch.........................28 Zoom..............................29 MarkerSearch.......................29 SpecialDVDFeatures...................29 TitleMenu..........................29 DiscMenu..........................29 InstallationandSetup . . . . . . . . .10 . CameraAngle.......................29 .29 ChangingtheAudioLanguage . Connecting to a TV & Decoder (or Satellite) .10 .11 Connecting to Optional Equipment .12-16 BeforeOperation-VCRpart. .12 Tuning in a video channel on your TV .12 Using your VCR for the very first time .13 SettingtheclockManually. Tosetthecoloursystem..............13 .14 Howtousingthemainmenu. .14 Tuning in TV Stations Automatically .15 TuninginTVStationsManually. .16 Changing the order of TV Stations DeletingTVstations..................16 .17-21 BeforeOperation-DVDpart. On-ScreenDisplay......................17 InitialSettings.......................18-21 GeneralOperation....................18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LANGUAGE.........................18 MenuLanguage....................18 DiscAudio/Subtitle/Menu. .18 DISPLAY...........................19 . . . . . . . . . . TVAspect.........................19 DisplayMode......................19 ProgressiveScan...................19 TVOutputSelect....................19 AUDIO.............................20 .20 DolbyDigital/DTS/MPEG. .20 SampleFreq.(Frequency) .20 DynamicRangeControl(DRC). Vocal.............................20 OTHERS...........................21 PBC.............................21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . AutoPlay..........................21 DivX(R)VOD.......................21 LOCK(ParentalControl)................22 Rating............................22 .22 Password(SecurityCode). . . . . . . . . . . . AreaCode.........................22 Operation....................23 Playingatape.......................23-25 .23 CM(CommercialMessage)Skip OPR (Optimum Picture Response) .23 .24 InstantTimerRecording(ITR). Timer recording using On Screen Display .25-26 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Subtitles............................29 .30 PlayinganAudioCDorMP3/WMADisc .31 AudioCDandMP3/WMADiscFeatures Pause..............................31 . . . . . . . . . . . MovingtoanotherTrack................31 RepeatTrack/All/Off...................31 Search.............................31 Random............................31 RepeatA-B..........................31 3DSurround.........................31 ProgrammedPlayback.....................32 .32 RepeatProgrammedTracks. .32 ErasingaTrackfromProgramList .32 Erasing the Complete Program List ViewingaJPEGDisc......................33 . . . . . . . . . . . . . . . . . . . . . . . . . SlideShow..........................33 StillPicture..........................33 MovingtoanotherFile.................33 Zoom..............................33 Torotatepicture......................33 To listen to MP3/WMA music watching picture .33 .34 PlayingaDVDVRformatDisc. . . . . . . . . . . . . . MaintenanceandService.................34 PlayingaDivXMovieDisc................35 Additional Features-VCR part . . . . . . . . . .36-37 . OnScreenDisplay....................36 TapeCounterMemoryStop.............36 Lock(ChildLock).....................36 .36 VideoDoctor(Self-Diagnosis). Hi-FiStereoSoundSystem.............37 .37 WideScreenCompatibility16:9 . . . . . . . . . . . . . . . . . . . Tosetthedecoder....................37 AdditionalFeatures.....................38 LastSceneMemory...................38 ScreenSaver........................38 VideoModeSetting...................38 Controlling other TVs with the remote control 38 CopyingfromDVDToVCR...............39 .39 Recording from another video recorder . . . . Reference....................40 LanguageCodes.......................40 CountryCodes.........................40 Troubleshooting........................41 Specification..........................42 3 Introduction To proper use of this product, please read this owner's manual carefully and retain for future ensure reference. provides information on the operation and maintenance of your DVD player. Should the unit require service, contact an authorized service location. Discs on Handling This manual Symbol Notes Discs Do not touch the the disc on by playback side of the disc. Hold edges so that fingerprints do not get the the surface. Never stick paper or tape on the disc. Used in this Manual The lightning flash symbol alerts you to the presence of dangerous voltage within the product enclosure that may constitute a risk of electric shock. The exclamation point alerts you to the presence of important operating and maintenance / servicing instructions. Indicates hazards unit itself or likely to other material cause harm to the damage. Storing Discs After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. Cleaning Discs Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center out. Note: Indicates special notes and operating features. Tip: Indicates tips and hints for A section whose title has is applicable only symbol. DVD VCD Do not strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static DVD and finalized DVD±R/RW use Selecting Video CDs MP3 MP3 Discs DivX of the spray intended for older Audio CDs JPEG the task easier. following symbols represented by the one to the disc CD WMA making the You must select VCR) to view on vinyl records. Viewing Source of your output the TV screen. one sources (DVD If you want to view DVD deck output source: Press DVD until DVD indicator in the display window or ? WMA Discs and JPEG Discs output source of DVD deck is viewed on lights the TV screen. If you want to view VCR deck output source: Press VCR until VCR indicator in the display window ? DivX Discs and output source of VCR deck is viewed on lights the TV screen. Notes: About the " ? Symbol Display " may appear on your TV display during operation and indicates that the function explained in this owner's manual is not available DVD video disc. 4 on that specific If you insert a disc while the DVD+VCR is in the VCR mode, the DVD+VCR will switch to DVD mode automatically. ? If you insert a cassette tape without prevention tab while the DVD+VCR is in the DVD mode, the DVD+VCR will switch to VCR mode automatically. Types of Playable Discs Regional code This DVD player is designed and playback of region DVD manufactured for (8cm/12cmdisc) encoded DVD software. This unit only Video CD (VCD) (8cm/12cmdisc) DVD discs labeled "5" Notes Audio CD ? (8cm/12cmdisc) on Regional can 5 "ALL". clearly a globe visible on with the one or more cover. This number must match your DVD code or the disc cannot play. addition, this unit plays DivX file, DVD -R, DVD +R, DVD -RW, DVD +RW, SVCD, and CD-R / CD-RW that contains audio titles, MP3, WMA, and/or JPEG files. play Codes Most DVD discs have numbers in it or "5" player's regional In This indicates ? If you try to play a DVD with a different region code from your player, the message "Check Regional Code" appears on the TV screen. product feature that is capable of playing DVD-RW discs recorded with Video Recording format. a Notes: ? Depending on the conditions of the recording equipment or the CD-R/RW (or DVD -R, DVD +R, DVD -RW, DVD +RW) disc itself, some CD-R/RW (or DVD -R, DVD +R, DVD -RW, DVD +RW) discs cannot be played on the unit. ? Do not attach any seal or label to either side labeled side or the recorded side) of a disc. ? Do not irregularly shaped CDs (e.g., heart-shaped or octagonal) since they may (the use result in malfunctions. Notes on DVDs and Video CDs Some playback operations of DVDs and Video CDs may be intentionally programmed by software manufacturers. This unit plays DVDs and Video CDs according to disc content designed by the software manufacturer, therefore some playback features may not be available or other functions may be added. Manufactured under license from Dolby Laboratories. are "Dolby" and the double-D symbol trademarks of Dolby Laboratories. DTS and DTS Digital Out Digital Theater Systems, are trademarks of Inc. 5 Disc-related terms PBC: DVD±R/DVD±RW version 2.0 disc formats. PBC allows you to interact with the system via menus, search functions, or other DVD -R and DVD +R Playback Control (Video CD only) Playback control is available for Video CD (VCD) are two different standards for recordable DVD drives and discs. This format allows information to be recorded onto the DVD disc DVD +RW and DVD -RW once. re-writable two standards for media, meaning the DVD erased and re-recorded. 4.38 are Gigabytes much. There only Single-sided content discs can can hold and double-sided discs hold twice are no dual layer single be as sided recordable discs. VCD A VCD holds up to 74 minutes (650 MB disc) or 80 minutes (700 MB disc) of MPEG-1 full-motion video with quality CDs. Title (DVD video discs only) A title is generally a distinct section of a DVD disc. For example the main feature could be title 1, a documentary describing how the film was made could be title 2, and cast interviews could be title 3. Each title is (Video CD) along typical computer-like operations. Moreover, still pictures of high resolution can be played if they are included in the disc. Video CDs not equipped with PBC (Version 1.1) operate in the same way as audio assigned easily. a reference number enabling stereo sound. Chapter (DVD video discs only) A chapter is a segment of a title such MPEG MPEG is an you to locate it international standard for video and audio compression. MPEG-1 is used in encoding video for VCD and provides for multichannel surround sound coding such as PCM, Dolby Digital, DTS and MPEG film or one interview in a series. Each as a scene chapter in a is assigned a chapter number, enabling you to locate the chapter you want. Depending on the disc, chapters may not be recorded. audio. Scene MP3 On MP3 is audio popular compression format used for digital files that yields very high near-CD quality. a WMA Windows media audio file. A developed by Microsoft type of coding / decoding (VCD) video CD with PBC (playback control) functions, moving pictures and still pictures are divided into sections called "scenes". Each scene is displayed in the menu screen and assigned a scene number, enabling you to locate the scene you want. A scene is composed of one or several tracks. a Corp. Track JPEG A distinct element of audiovisual Joint Pictures Expert Group. file format that allows you to on the number of colors. JPEG is save compressed images with no limit a information, such the picture or sound track for a specific language (DVD), or a musical piece on a video or audio CD. Each track is assigned a track number, enabling you to locate the track you want. DVD discs allow DivX track of video DivX is the name which is based on of a revolutionary the new MPEG-4 standard for video.You will be able movies 6 using this DVD new player. video codec compression to play DivX as of audio. (with multiple angles) one and several tracks Front Panel POWER Switches the unit to ON or OFF. Reverse Go to Skip/Scan, Rewind ( ) beginning of current chapter/track or to Press and hold for two seconds for Rewinds the Disc a fast PREVIOUS reverse chapter/track. search. tape. Tray PLAY Starts Insert disc here. a ( G) playback. Forward Go to Skip/Scan, Fast-Forward ( NEXT chapter/track. Press and hold for two seconds for Winds the a ) fast forward search. tape forwards. STOP ( A Tape Eject ) Stops playback. DVD OPEN/CLOSE Opens Display or ( Tape Compartment ) closes the disc tray. DVD/VCR Selector Audio IN window (L/R) Shows the current status of the unit. Video IN Jack Remote Sensor Point the remote control here. Display Channel Programme Selectors. Window Child Lock is Indicates Indicates the engaged repeat mode. DVD+VCR is in timer timer recording Progressive a VCR disc is loaded in the DVD deck and flashes when no or a VCR deck is selected. A disc is loaded in the DVD deck. when is recording programmed. A Cassette is in the VCR deck. Scan is set to On mode. (Lights Jacks recording is engaged. DVD to VHS copy is in progress. disc is Indicates TV mode. loaded.) (See Notes on page 24.) DVD deck is selected. DVD VCR P REC TV Indicates total playing time/elapsed time/current time 7 Remote Control POWER Switch this unit ON or OFF. DVD/VCR select button Selects operational mode of remote control. OPEN/CLOSE EJECT Open or close the the disc - - (see - VCR: Rewinds the STOP mode, for fast TV VOL +/--: tape during the reverse ( ) Pause playback temporarily / press repeatedly for frame-byframe playback. PLAY (G) Starts playback. STOP(A)? Stops playback. ? Access the with PBC. Displays ? ? ? ? Play language (DVD). subtitle a LOCK language. input sources (Child Lock) on into tape. and off. TITLE Display the title menu of the disc if available. DISC MENU of a DVD disc. PROGRAM Access or remove program menu. MARKER Mark any point during playback. ? ? ? Repeat sequence. recording speed of SEARCH Display MARKER SEARCH ? tape. RANDOM/CM SKIP tracks in random order. CM SKIP ? - audio Switch the Child Lock ENTER/OK menu selection. the an REC/ITR Record your - Select the video CD ? - - a ? Select channel programme of VCR. To adjust tracking. To control vertical tremble during picture still. - of ANGLE Select DVD camera angle if available ZOOM Enlarge video image. menu A-B/LP menu ? PR/TRK(+/-) menu menu. SUBTITLE Select FGDE(left/right/up/down) Access setup AUDIO Select counter. Acknowledge or remove RETURN DISPLAY CLK/CNT Access the On-Screen Display. Shows you the current time or - off TV sound. SETUP/ i ? item in the on or TV's volume. SKIP(./>) Go to next chapter or track. Returns to beginning of current chapter or track or go to previous chapter or track. search. an Adjusts MUTE: Turns picture search and Advances the tape during the STOP mode, fast forward picture Select source. TV PR +/--: Selects TV's channel. forward. PAUSE/STEP recording off the TV. on or TV AV: Selects the TV's (m/M) or for 38) p. TV POWER: Turns BACKWARD / FORWARD DVD: Search backward source TV Control Buttons TV/VCR Switch between your TV's tuner and the VCR's internal tuner. - Tape Eject. AV Select input into tape. 0-9 numerical buttons Select numbered items in a menu. tray. ? - - menu. CLEAR Clear a track number on the program menu or a mark on the MARKER SEARCH menu. Reset tape counter to zero. REPEAT Repeat chapter, track, title, all. - ? Remote Control Remote control Operation Point the remote control at the remote sensor mix different Detach the battery of the remote new batteries and types of batteries such dard, alkaline, etc. 8 installation and press the buttons. Do not mix old and battery never as stan- AAA AAA batteries cover on the control, and insert (size AAA) aligned correctly. with and rear two Rear Panel VIDEO/AUDIO Connect to a OUT(Left/Right) (DVD/VCR OUT) TV with video and audio inputs. COMPONENT/PROGRESSIVE SCAN VIDEO OUT (DVD EXCLUSIVE Connect to a TV with Y Pb Pr AUDIO OUT Connect the aerial Connect to this Pb Pr) OUT) AERIAL using (Y inputs. (Left/Right) (DVD EXCLUSIVE OUT) an amplifier, receiver or stereo system. EURO AV2 DECODER jack. Connect to pay-TV decoder or another video recorder. OPTICAL (Digital audio out jack) Connect to digital (optical) audio equipment. S-VIDEO OUT Connect to EURO AV1 AUDIO/VIDEO Connect to your TV set a EXCLUSIVE TV with S-Video (VCR or (DVD IN+OUT / DVD OUT) input. OUT) another video recorder. COAXIAL Connect (Digital audio out jack) (DVD EXCLUSIVE OUT) to digital (coaxial) audio equipment. RF.OUT Connect to your TV using this jack. AC Power Cord Connect to a power source. Do not touch the inner panel. Electrostatic damage to the unit. pins of the jacks on the rear discharge may cause permanent 9 Installation and Setup Progressive Scan Tips: If your television is high-definition or "digital ready" television, you may take advantage of the DVD Player's progressive scan output for the highest video resolution possible. Depending your TV and other equipment you wish to connect, there are various ways you could on connect the unit. Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the For better sound Make sure this unit is connected Set the TV to the correct video directly to the input channel. Do not connect this unit's AUDIO OUT in phono jack (record deck) on (AV) the TV on of this unit to the SCART panel using Connect the COMPONENT/ PROGRESSIVE SCAN VIDEO OUT sponding jacks on the DVD Player jacks on the TV using the in on input to the corre- Y Pb Pr cable. Right AUDIO OUT jacks of the audio left/right in jacks on the TV Connect the Left and DVD Player using the audio cables. to the Notes: Progressive to "On" on the setup progressive signal, see page 19. Set the does not work with the Progressive scan connections (yellow VIDEO OUT jack) or menu for analog video S-VIDEO connection. Rear of DVD+VCR Connect the EURO AV1 AUDIO/VIDEO rear 2. system. of the Basic connection 1. of your audio to the following connections, depending capabilities of your existing equipment. one the jack TV. to a TV & Decoder Connecting Make 1. 2. Caution: a If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the DVD Player. best connections. reproduction, connect this unit's AUDIO OUT jacks to the audio in jacks of your amplifier, receiver, stereo or audio/video equipment. See "Connecting to optional equipment" on page 11. connection (Component Video connection) the socket RCA-SCART lead. a Some TV broadcasters transmit encoded television which you can only see with a purchased rented decoder. You can connect such a signals or decoder (descrambler) Basic connection 1. to this unit. (RF) Connect the RF antenna cable from your indoor/ outdoor antenna to AERIAL jack on the rear panel of this unit. 2. Connect the RF.OUT jack Rear of TV supplied the on television's Antenna RF antenna cable from the panel Input. rear of this unit to your AERIAL VIDEO INPUT AUDIO INPUT L R Pr DVD exclusive out connection AUDIO Component 1. Video (Color Stream ) COMPONENT VIDEO INPUT/ PROGRESSIVE SCAN AUDIO OUT(L) Pb Y OUT(R) Decoder connection S-VIDEO INPUT (or Satellite) VIDEO OUT Connect the COMPONENT/PROGRESSIVE SCAN VIDEO OUT the jacks on the DVD Player to corresponding in jacks on the TV using the Y Pb Pr cable. 2. Connect the Left and Right AUDIO OUT the DVD the TV Player to the audio left/right using the audio cables. in jacks of jacks on S-Video connection 1. Connect the S-VIDEO OUT S-Video input jack on the jack on this unit to the TV using the S-Video Rear of DVD+VCR cable. 2. Connect the Left and the DVD the TV 10 Right AUDIO OUT to the audio Player using the left/right audio cables. in jacks of jacks on (Basic connection) Note: If the TV has with the S-video cable. input, connect the DVD player When using an S-video cable, do not connect the video cable. an S-video yellow Connecting Optional Equipment to Connecting to an amplifier equipped with channel analog stereo or Dolby Pro Logic II /Pro Logic two Connect the Left and this Right and right unit to the audio left er, receiver AUDIO OUT in jacks on your amplifisystem, using the audio cables. stereo or jacks on Notes: If the audio format of the the capabilities of produce a strong, To see digital output does not match your receiver, the receiver will distorted sound or no sound at all. the audio format of the current DVD in the On-Screen Display, press AUDIO. Connecting to an amplifier equipped with two channel digital stereo (PCM) or to an Audio/ Video receiver equipped with a multi-channel decoder (Dolby DigitalTM, MPEG 2 or DTS) 1. Connect this unit's DIGITAL AUDIO OUT jack the corresponding an optional digital (OPTICAL or COAXIAL) to jack on your amplifier. Use (optical or coaxial) audio cable. 2. You will need to activate this unit's "AUDIO" (See Digital on InstaliodSeup in digital output. 20). page Multi-channel sound A digital multi-channel sound quality. For this connection provides the best you need a multi-channel Audio/Video receiver that supports one or more of the audio formats supported by your unit (MPEG 2, Dolby Digital and DTS). Check the receiver manual and the logos on the front of the receiver. Warning: Due to the DTS output will be in Licensing agreement, the digital DTS digital out when DTS audio stream is selected. Rear of this unit 2 channel analog stereo or Pro Dolby Logic II/Pro Logic connection. DVD exclusive out DVD/VCR OUT Digital COAXIAL DIGITAL INPUT multi-channel connection L (DVD exclusive out connecttion) R OPTICAL AUDIO INPUT DIGITAL INPUT Amplifier (Receiver) 11 Before in Tuning Operation-VCR part video channel a on TV your Notes: The output frequency of this video recorder (VCR) RF another TV by torted, you station, or if the already picture is dis- change 8 will show you how your VCR. Stages 5 change the output frequency of your VCR. Your TV receives signals You called AV 1. Make VCR on Select Insert it, usually video tape into your VCR and press N on the remote control. Select a TV channel number on which you wish to watch video's. Don't worry if you don't have a VCR on play 3. at this and continue ing video playback bright blue screen. stage! stages 3 If you switch your 4, instead of see- tune your TV until you picture see a is sharp and the sound is clear. If you have used a RCA-SCART cables you will not have to tune your TV, simply select the AV channel. The AV channel is already pre-tuned for 4. video playback Store this channel I on the front of your VCR when you Tune this channel so appears. Store this channel on that on your TV. your TV. You will need to look at the TV instruction book if stages 1 on stages 4. Select ~ a 5 6. TV channel number your TV. If you do not tune in a dedicated video channel on your TV you will be unable to view and record video tapes! on Using your VCR for the very first time Following picture will display on the TV screen when you have just connected your video recorder for the very first time. To make tuning 3 to 4 shown "ACMS" as TV stations, please follow stages (see p.14). more Pr-12 (3/4) on the front of your VCR for than 4 seconds. RF36 will appear in the display window. The following picture will be displayed on the TV screen. 12 ACMS on displayed). Press PROG. screen that you have correctly installed your VCR and successfully tuned in a dedicated video channel ~ which you wish to watch video's. Make sure that your VCR is in standby pressing POWER on the remote control (only the clock will be blue sure 8 if you cannot obtain clear video playback as described in Only carry out bright your TV. you do not know how to do this. 5. a ~ Tune this channel until the video optimum which you wish to Note: pre-recorded to on your VCR. on your TV. video-tape TV channel number have finished. that you have correctly installed your described earlier in this book. a a Press Make 2. RCA-SCART lead. watch video's. . Press POWER to turn Turn 8. sure as a a on dedicated video channel built into a to select another video can VCR with your TV and tune it in so that you may watch video tapes. If you have used a RCA-SCART cables then your TV should already have (3/ 4) also set it to "OFF" if there is any interference when your TV is connected to the from the video recorder like another TV station. You have to select channel number Press PROG. channel. You may select any channel number between 22 and 68. to ~ (VCR) 7. the transmitter channel of can 36 PSET R is set at UHF channel 36. If channel 36 is used CHANNEL ACMS Setting the clock Manually The clock in your VCR controls time and date settings for your VCR. 1. Press i. Press 1 or 2 to select SET. Press OK. To set the colour system 1. Press i. 2. The main 3. Press 1 or 2 to select the SYS and press OK. 4. Press 3 or 4 to select menu will appear on the TV according screen. to the COLOUR system used. HHMNDDMMYY -- :. - - -- -- -- --- . 12 SYS i SET ON OFF 2. Use the v or V on i the remote control to alter the HOURS, MINUTES, DAY, MONTH and YEAR. 5. Please note your VCR uses a 24 hour clock. e.g. 1pm will be displayed as 13:00. The InstaliodSeup SYS fOSD of the week will appear when you enter the year. day Press 1 or 2 to select the RF AUDIO. Press 3 or 4 to select according to the RF AUDIO used. automatically SYS HHMNDDMMYY 8 SYS fOSD ON OFF :. 0010105SAT i . 6. 12 i SET 3. If you make a mistake press 1 correct details. 4. Press i. or Press i to remove the menus from the TV screen. 2 and enter the 13 How to using This VCR easily be programmed by using displayed on screen. the menu can menus The the main controlled from the Remote menus are Control Handset. 1. Switch your TV set and video recorder the POWER button. on pressing 2. by menu will appear on the TV Tuning Automatically If the TV broadcast signal is weak your VCR may not detect the necessary information and will not be able to store them correctly. To overcome this turn to the MANUAL TUNING problem please section Press i button. The main in TV Stations on page 15. 1. Press POWER to turn 2. Press i button. your DVD+VCR. on screen. The main menu will appear on the TV Press 1 or 2 to select the ACMS. screen. Press OK. SET SYS fOSD ON OFF ACMS Pr-12 SET REC Timer recording setting (see p. 25). PR SET Manual tuning setting (see p. 15). ACMS ACMS (Automatic Channel Memory System) (see p. 14). SET Date & clock setting (see p. 13). SYS To set the Colour TV System (see p. 13). (Dr.) To check a problem with your VCR (see p. 36). F.OSD ON/OFF To display the operational - Pr-12 fOSD ON OFF Pr-12 ACMS - - 3. Press OK again to start the automatic tuning process. - - - 01 C02 00 PR-01 02 C03 00 PR-02 03 C04 00 PR-03 - mode of your VCR (see (16:9/4:3) - p. S 36). To select the Pr-12 ACMS aspect ratio of your TV DECODER NIC - (see p. 37). To use a pay-TV decoder (or Satellite) with your VCR (see p. 37). improve the playback picture (see p. 23). To activate or deactivate the NICAM digital sound (see p. 37). (OPR) O - - To 4. The TV STATION TABLE will appear when is completed. Press i to save your Tip: change the menu language on the DVD setup menu. (See the Menu Language on page 18.) 3. can Press 1 and 2 to select the desired Press OK and press 3 4. 14 Press i to remove the or menu. 4 to select. menus from the TV screen. settings. 02 C03 00 PR-02 03 C04 00 PR-03 04 C05 00 PR-04 05 C06 00 PR-05 06 C07 00 PR-06 07 C08 00 PR-07 08 C09 00 PR-08 PSET R You E MOVE : DELETE : , tuning in TV Stations Tuning In certain areas of the Manually country broadcast signals CH 04 C04 may be too weak for your DVD+VCR's automatic tuning process to find or assign TV stations PR : AV PSET R You must tune in these weaker broadcast stations 6. in order for your DVD+VCR to store Press i. The main Press 1 will appear on the TV 2 to select the PR SET. menu or Press 2 to select STATION so that you may name your TV station. Press OK. them. 1. STATION CHANNEL/CABLE correctly. manually MFT 7. screen. Use 3 or station name. Use 1 Press OK. or 4 to select letters and numbers for the 2 to move back and forth between characters. Press OK. PR CH 01 MFT STATION 00 PR-03 Pr-12 ACMS SET SYS fOSD CHANNEL/CABLE ON OFF : AV PR CH MFT 04 C04 00 STATION PSET R 2. PSET R Press i. The station table will appear. 3. Press 3 8. Press i, confirm the station placement. 4 to select the programme number that you want to tune (for example, PR 04). or 01 C01 00 PR-01 02 C02 00 PR-02 03 C03 00 PR-03 -- -- ----- -- -- ----- -- -- ----- -- -- ----- 05 06 07 08 PSET R MOVE : DELETE : PR CH MFT 04 C04 00 STATION PSET R If you wish to stages 3 8. , manually tune other stations repeat - 4. Press OK. Press AV to select C (Standard stations) or S (Cable stations): C02 - C69, S01 - tune, use 3 or S41. 4 to find the MFT STATION -- ---- 04 PR-01 02 C02 00 PR-02 03 C03 00 PR-03 07 required 08 station. PSET R Press i Your CH 00 06 9. PR C01 05 Enter the channel number of station that you want to 01 CHANNEL/CABLE : -- -- ----- -- -- ----- -- -- ----- -- -- ----- MOVE : DELETE : , again. new TV station has now been tuned into your DVD+VCR. AV P SET R 5. Searching will stop when it locates a stations. Press 2 to select MFT. Control the fine tuning of the station by using 3 or 4. 15 the order of TV Stations Changing After tuning TV stations into your VCR you may wish to change the order in which they are stored without having to retune them against! The instructions given on this page will show you how you can simply move them into your desired Deleting After TV stations into your VCR you may wish to delete a station. tuning how you stations. 1. order. 1. TV Stations can Press 1 The main Press 1 will appear on the TV 2 to select the PR SET. menu or delete any unwanted TV Press i. The main Press i. easily will appear on the TV 2 to select the PR SET. menu or screen. Press OK. screen. Press OK. PR CH 01 MFT STATION 00 PR-03 Pr-12 ACMS SET SYS fOSD PR CH MFT STATION 00 PR-03 01 CHANNEL/CABLE ON OFF : AV PSET R Pr-12 ACMS SET SYS fOSD CHANNEL/CABLE ON OFF : AV P SET R 2. 2. Press i. 3. Press 3 Press i. Press 3 4 to select the or you want to Press 2. move PR 4 to select the you want to delete. programme number (for example, or 02 C02 00 PR-02 03 C04 00 PR-04 05 01 C01 00 PR-01 01 C01 00 PR-01 06 02 C02 00 PR-02 02 C02 00 PR-02 07 03 05 06 07 08 C04 PR-04 04 00 -- -- ----- 05 -- -- ----- 06 -- -- ----- 07 -- -- ----- 08 PSET R MOVE : DELETE : 08 C04 00 -- C03 -- PR 01) ----- 00 PR-03 -- -- ----- -- -- ----- -- -- ----- PR-04 -- -- ----- -- -- ----- -- -- ----- -- -- ----- PSET R 4. PSET R , (for example, 03). 04 04 programme number MOVE : DELETE : , Press 1. After a short while, the selected station will be deleted. 3. Press 3 4 to select the or you want to move to programme number (for example, 01 C01 00 PR-01 02 C02 00 PR-02 03 C04 00 PR-04 04 -- -- PR If you wish to delete other TV stations stages 3 4. 05). - 02 03 07 08 04 05 -- -- ----- -- -- ----- -- -- ----- 06 07 08 PSET R 4. 5. The selected programme will be moved to the new programme number. move other TV stations repeat - 01 C01 00 PR-01 02 C02 00 PR-02 03 C04 00 PR-04 04 06 07 08 -- -- ----- -- -- ----- -- -- ----- -- -- ----- PSET R 5. 16 Press i to remove -- C03 the 00 PR-04 -- ----- MOVE : DELETE : menus , from the TV screen. Press i to remove 00 PR-03 -- -- ----- -- -- ----- -- -- ----- -- -- ----- PSET R Press OK. If you wish to stages 1 4. C02 ----- 05 06 repeat the MOVE : DELETE : menus , from the TV screen. Before Operation-DVD part On-Screen You Display the general playback status on the TV screen. Some items can be changed using the menu. To use the on-screen display: display can Press DISPLAY 1. The selected item is Press b / B to 3. an inputting Title Number the change the title Chapter highlighted. For number). some also If no provide button is on-screen Playback Title A-B for 10 1/12 functions, B, Numbers ENTER 0:20:09 Numbers, ENTER b/Bor AUDIO InstaliodSeup setting. all of the features seconds, the pressed display disappears. language ABC b/Bor 1 ENG SUBTITLE Angle b/Bor 1/3 ANGLE Sound 3D SUR b/B Status/Restrictions Example: On-Screen Display during playing VCD Repeat title Repeat sequence Selection Method Items 1/9 b / language and Digital Audio Output mode Notes: ? B, Numbers Audio Subtitle Some discs may not shown below. Number Time search setting. You can appropriate (e.g. press ENTER to execute the ? 1/3 b / ENTER item. the number buttons if use Selection Method Items during playback. Press v / V to select 2. Example: On-Screen Display during playing DVD Video Enter a Marker Track Number MARKER SEARCH 123456789 Marker Search menu (or PBC 1/3 Action play from this prohibited or ENTER Numbers 0:20:09 point not available B, Numbers mode) Time search Resume b / ENTER b/Bor Audio Channel STEREO Sound AUDIO 3D SUR b/B Example: On-Screen Display during playing divx movie disc Selection Method Items Track Number 1/3 b / B, Numbers ENTER Time search 0:20:09 Audio language and Digital Audio Output mode Subtitle Sound language b/Bor 1 MP3 ABC Numbers, ENTER ENG AUDIO b/Bor SUBTITLE 3D SUR b/B 17 Initial LANGUAGE Settings LANGUAGE By using the Setup menu, you can make various adjustments to items such as picture and sound. You can also set a language for the subtitles and the Setup menu, among other things. For details on each Setup menu item, see pages 18 to 22. To display display the Disc Subtitle Off Disc Menu Original 2. Use v / V to select the desired alternate Setup menu appears. option then press to the second level. The screen shows the selected item, Use v / V to select the second desired press B to move as well option as then Select a language for the Use v / V to select the desired 5. Press SETUP then press ENTER to confirm your selection. Some items require additional steps. N to exit the setting Setup Original: Refers to the disc recorded. was Setup menu and on-screen DVD menu. original language Other: To select another track in which the language, press number buttons then ENTER to enter the corresponding 4-digit number according to the language code list in the reference chapter. If you enter the wrong language code, press CLEAR. to the third level. 4. or Language language you prefer for the audio (disc audio), subtitles, and the disc menu. Press SETUP. The setting for setting(s). Select Select the 1. the current Menu Disc Audio / Subtitle / Menu Operation move Move display. To go back to the previous level: Press b on the remote control. 18 Original screen. To go to the next level: Press B on the remote control. 3. Disc Audio A second press of menu. SETUP will take you back to initial B to English Language and exit the Menu: Press SETUP to General Menu 4. When the confirm DISPLAY Cancel is DISPLAY TV 16 Aspect Display Mode Progressive TV Output menu : to 9Wide highlighted highlight Enter. as appears on your screen default. Use the b button Widescreen Scan 5. Off Select Pressing scan RGB ENTER will set this unit to Progressive mode. Caution: Once the Move TV : Select DVD Aspect 4:3 setting for progressive scan output is entered, an image will only be visible on a progressive scan compatible TV or monitor. If you set Progressive Scan to Select when a On in error, you must reset the unit. 1) Remove any disc from the unit and close the disc tray. See that "DISC" is displayed on the display window. standard 4:3 TV is connected. 16:9 Wide: Select when 16:9 wide TV is connected. a 2) Press STOP and hold it for five seconds before Display Display DVD Mode Mode setting works only when the TV TV LetterBox: Displays a wide picture with bands upper and lower portions of the screen. on the Output Set this unit TV Scan Progressive Scan Video provides the highest quality pictures with less flickering. If you are using the Component Video jacks for connection to a TV or monitor that is compatible with a progressive scan signal, set Progressive Scan to On. Output Select options according to the type. YPbPr: When your TV is connected with the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks progressive Select TV connection Panscan: Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit. To turn On it. The video Aspect mode is set to "4:3". Progressive InstaliodSeup output will be restored to the standard setting and a picture will once again be visible on a conventional analog TV or monitor. releasing on this unit. RGB: When your TV is connected with the SCART (RGB signal) jack. scan: Connect component out of this unit to the input of your monitor/television, set your television or monitor to Component Input. 1. Select "Progressive Scan" on the DISPLAY menu then press B. DISPLAY TV Aspect Display Mode Progressive TV Output Scan On Off Select Prev. 2. Select "On" using Move Enter the v / V buttons. 3. Press ENTER to confirm your selection. The confirm menu will appear. Note: If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the DVD Player. 19 AUDIO Each DVD disc has Set this unit AUDIO audio system you variety of audio output options. options according to the type of a use. AUDIO Dolby Digital Bitstream DTS Bitstream MPEG PCM Sample Freq. 48KHz DRC On Vocal On Move Dolby Digital Select DVD / DTS / MPEG DivX Bitstream: Select "Bitstream" if you connect the DVD Player's DIGITAL OUT jack to an amplifier or other equipment with Dolby Digital, a DTS or MPEG decoder. PCM MPEG): Select when connected to a two-channel digital stereo amplifier. DVDs encoded in Dolby Digital or MPEG will be automatically downmixed to two-channel PCM (for Dolby Digital / audio. Off not (for DTS): If you select "Off", the DTS signal output through the DIGITAL OUT jack. is DVD Sample Freq. (Frequency) If your receiver or amplifier is NOT capable of handling 96 kHz signals, select 48 kHz. When this choice is made, this unit automatically converts any 96 kHz signals to 48 kHz so your system can decode them. If your receiver or amplifier is capable of handling 96 kHz signals, select 96 kHz. When this choice is made, this unit passes each type of any further processing. signal through Check the documentation for your its capabilities. Dynamic Range With the DVD Control format, you amplifier DVD (DRC) can hear a without to verify DivX program's soundtrack in the most accurate and realistic presentation possible, thanks to digital audio technology. However, you may wish to compress the dynamic range of the audio output (the difference between the loudest sounds and the quietest ones). This allows you to listen to a movie at a lower volume without losing clarity of sound. Set DRC to On for this effect. Vocal DVD Set to On playing. only when multi-channel karaoke DVD is The karaoke channels normal stereo sound. 20 a on the disc mix into OTHERS The DivX(R) PBC, Auto Play and DivX(R) VOD settings can be changed. You VOD DivX display the DivX DRM (Digital Rights Management) Registration code for your unit only. can OTHERS PBC Auto DivX(R) On Off Play Your DivX(R) Video On Demand VOD Select registration code is To learn more : XXXXXXXX visit www.divx.com/vod (Done) Move Select The PBC Set Registration code is used for VOD (Video-OnDemand) service agent. You can purchase or rent an VCD Playback Control (PBC) On: Video CDs with PBC to On are or encrypt Off. played according to the PBC. Off: Video CDs with PBC are played the same way as Audio CDs. Auto You Play move Notes: If you rent the DivX VOD file, it has several viewing limits as shown below. ? Display DVD set up the DVD Player so a DVD disc automatically starts playing whenever the DVD is inserted. Play mode is set to play back the title longest playback automatically. On: Auto Play function is active. Off: Auto Play function is not active. Play function may not work for DivX(R) can options of watch the file. VOD Rental This rental has 3 views left. Do you want to On, this DVD player will search for title that has the then the number which you View can If Auto InstaliodSeup file. use one of your 3 views now? time and (Yes) (No) ? The rental has been expired. Notes: The Auto some DVDs. Rental Expired (Done) ? Display the authorization error. Authorization Error This player is not authorized to play this video. (Done) 21 LOCK Password (Parental Control) You LOCK Rating Unlock Password New Area Code RU (Security Code) enter can 2. Follow step Input Move shown left 4-digit code, again to verify. it that may not be suitable of these discs contain scenes Many parental control information that applies to the complete disc or to certain scenes on the disc. Movies and scenes are rated from 1 to 8, depending on the country. Some discs offer suitable more scenes as an control feature allows you to block to scenes below the rating you input, there new 1. Press SETUP to 2. Input the 6-digit display Enter a new code 1. Select Enter the code of the "Rating" on the LOCK menu then Setup clear it using menu. security Rating, Password and Country Code features, you must input the 4-digit security code you created. If you have not yet entered a security code you are prompted to do so. the Input a 4-digit code and press ENTER. Enter it again and press ENTER to verify. If you make a mistake before pressing ENTER, press CLEAR. rating a from 1 to 8 using 1. tions and Rating one (1) rating eight (8) is the least restrictive. Unlock If you select and the disc unlock, parental control is plays not active in full. Notes: rating for the player, all disc scenes with rating or lower are played. Higher rated are not played unless an alternate scene is a on the disc. The alternative must have the rating or a lower one. If no suitable alternative found, playback stops. You must enter the 4-digit password or change the rating level in order to play same is the disc. 4. Press ENTER to confirm your rating press SETUP to exit the menu. selection, then whose standards disc, based on the chapter. Select "Area Code" on the LOCK menu then press 2. Follow 3. Select the first character 4. Press ENTER and select the second character using the v / V buttons. has the most restric- country/area B. 5. 1-8: described above. DVD list in the reference access as used to rate the DVD video were press B. available the can by Area Code scenes menu. number "210499" and the your children from being able to view material you believe is unsuitable. If you set the same or then press ENTER. If you forget your security code you the following steps: 3. preventing Rating (Rating). "Change" code is cleared. parental 3. Select then press B. forget your Security Code If you alternative. 2. To menu Select DVD for children to view. 22 as the LOCK 4. Press SETUP to exit the Some movies contain access 2 on highlighted. 3. Enter the The change password. 1. Select Password "New" is Rating or step 2 as shown left (Rating). using v / V buttons. v / V buttons. Press ENTER to confirm your selection. country code Operation Playing You will only a Logic search: During fast forwarding tape be able to load and eject video rewinding press and hold FORWARD or BACKWARD the picture will be played back at 7 times normal playback speed. cassettes when your VCR is plugged into the mains. Your VCR may also playback recordings from NTSC tapes (on PAL Getting a better When cassette is inserted and a 5. TV). picture playback started, the automatic tracking function works to get the best possible picture automatically. If the quality of the recording is poor, repeatedly press TRK + or on the remote control to manually adjust the tracking until any distortions have to switch automatic 1. Make back tracking on on as Turn on again. reduce them with TRK that you have correctly connected your described earlier in this book. your TV. Press POWER to turn may appear on the picture according to the status of tape. If distortions can be seen in the picture, the remote control sure VCR 6. 2. Press N to start facing your tape. video cassette which has had its cassette will start removed, playback of the automatically. AUTO TRACKING Your VCR will give 3. the best automatically adjust picture quality. Press PAUSE/STEP to still the tracking to 1 Press 30 seconds 3 Press 90 seconds a 4 Press 120 seconds the 5 Press 150 seconds 6 Press 180 seconds down at about 1/19 times the normal OPR can be playback for up to 5 minutes. After 5 minutes your VCR will stop the tape to prevent damaging the tape or your VCR paused Still picture quality can pressing TRK + or be improved slightly by playing your tape. Double speed playback Press the "N (X2)" button during normal playback. The tape will play back at double speed normal (X2)" Response) 1. Press i. 2. Press1or2toselectOPR( 3. Press OK. 4. Press 3 or 4 repeatedly ). to select: OFF, SOFT or SHARP. and without sound. Press the "N Picture automatically improves playback picture quality by adjusting your VCR to the condition of the tape. Please note that the OPR icon ( ) will only appear in play that mode when playing a tape. -. Press N to continue (Optimum This feature . 4. (Commercial Message) Skip: This feature enables you during playback of a tape to skip a commercial break in a few seconds, then resume normal playback. While tape is playing press CM SKIP on the remote control to skip commercial (or another programme material). Repeatedly press CM SKIP to skip: tape frame by frame. If you press FORWARD, the picture will be slowed Tapes Operation 2 Press 60 seconds picture. repeatedly to advance Press PAUSE/STEP playback. CM away from you. playing If you load a record protection tab -. tape is reached, your VCR will stop playback automatically, rewind, stop, eject the tape. on arrow or If the end of the The video cassette should have the window side up and the Press STOP to end + Press EJECT. your VCR. Insert the video cassette into your VCR. facing playback, Shuttle : During playing back or still picture press F or G. You can reach the following playback speeds. (-7xplay, -3xplay, -play, still, 1/19 slow, play, 2xplay, 7xplay). To switch off the slow motion and Slow motion shuttle, press the desired function. During slow motion and shuttle, the noise bars - been removed. Press numbered 0 or button to return to playback Please note you may at playing speed. 5. Picture search: a only set OPR when tape. Press i return to screen. back press either FORWARD or BACKWARD and this will enable you to rapidly During playing wind the tape (7 times normal playback) and where you are on the tape. see Pr-12 PSET R ACMS OFF SOFT SHARP fOSD ON OFF 23 Instant Timer 5. Recording (ITR) Your VCR allows you to make variety of simple methods: recordings using produce improved picture and quality, however LP will provide twice recording time as SP. Instant Timer video cassette Your VCR runs Press REC/ITR to start which will record up to 180 minutes using Standard Play (SP); using LP you will be able to record up to 360 minutes. Please note there will be Make VCR quality when slight using LP. a 7. 2. Insert Press PAUSE/STEP to avoid protection your VCR. The video cassette should have the window side facing 3. 4. up and the Press PR arrow facing away from you. to select the programme number you wish to record. + or - paused for up to 5 minutes; RECP will be displayed when a tape is paused. After 5 minutes your VCR will stop recording to prevent damaging the tape or your VCR. EJECT will appear seconds. from EURO AV1 SCART socket of your unit. AV 2 for recording from EURO AV2 SCART socket on the recording of your unit. AV 3 for recording from VIDEO IN and AUDIO IN on the rear (Left & rear Right) sockets on the front of your unit. on the TV screen for few a Notes: If you do not wish to record on a tape (this can happen quite easily by accident!) remove the protection tab on the back edge of the video It is AV 1 for recording. Press EJECT. control. displayed. be Press STOP to end cassette. you wish to record from is 24 can You may also directly select programme number using the numbered buttons on the remote If you wish to record directly from the SCART or RCA sockets repeatedly press AV until the socket unwanted If you press PAUSE/STEP unit will enter the record pause mode and ITR is cancelled. 8. tab into recording recording. during ITR, this loss in your VCR. on video cassette with a recording. Press PAUSE/STEP to continue that you have correctly connected your described earlier in this book. Press POWER to turn much as scenes. sure as sound press will increase the record time by 30 minutes until you reach a maximum of 9 hours. Tapes 1. or RECORD will appear on the TV screen. Press REC/ITR several times. Each successive incorporates Long Play (LP) and sound 6. out. enables you to record up to twice the amount of time on a video cassette. For example an E-180 picture Long Play SP will a Recording (ITR) start recording immediately for a set period of time or until the Press LP if you wish to record in Standard Play. possible to record on a video cassette record protection tab removed by covering with self adhesive with the the hole tape. Remember you can record one programme while watching another by starting your instant recording, press TV/VCR to appear TV indicator in the display window and then selecting a different channel on your TV. recording using On Screen Display Timer PR DATE TIME PR-03 You may set up to seven timer record events within one month of the current date. :: -- -- -~ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- :: -- -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ SP -- SP -- SP -- SP -- SP -- SP -- SP -- SUMOTUWETHFRSA Note: Before setting the timer make set the DVD+VCR clock sure correctly that you have and you know which stations you have tuned TV stations your DVD+VCR. 6. Use v/V/1/2 buttons to enter the Insert a video cassette with protection on Please note your DVD+VCR uses a 24 hour clock. e.g. 1pm will be displayed as 13:00. 2. up and the facing arrow DATE PR-03 tab into your DVD+VCR. The video cassette should have the window side facing away from you. ). 7. Press OK. 41 4 :: 00 1 5 SP ~ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Press B to select the Press v PR DATE (SP, IP, TIME -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ SP -- SP -- SP -- SP -- SP -- SP -- :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ SP -- SP -- Use the PR/TRK (v/V) necessary, to , PR-03 the timer record event. setting tape is left and SP -- PR Press OK to start tape speed LP). speed from SP to LP, if complete recording the program. SP -- or V to select the desired switches SP -- or recording speed. IP mode determines how much SP -- DELETE: 4. TIME Press i. Press1or2toselectREC( 3. start and end times of the programme that you wish to record. PR 1. recording to enter the station that DATE TIME 41 4 :: 00 1 5 30 ~ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ -- -- -- -- -- -- SP SP SP SP SP SP you wish to record then press 2. PR DATE TIME -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ :: -- -~ -- -- -- -- -- -- -- SP SP SP SP SP SP SP Note: If all timer record events full press v or V to select the event that you wish to remove and replace. Press b to delete the event. 5. Use the PR/TRK are (v/V) to enter the date of the programme. If you press OK before select one of the entering the date you may following automated recording features. Press 1 or 2 to select, then press OK DLY To record every day (except Sunday) at the same time. SU~SATo record at the same to confirm. Saturday and time every week. 25 recording using On Screen Display (Continued) Timer 8. Press i to set another timer record event and follow 3 to 8. steps Check that the timer event details Press i return to correct. screen. If PLEASE CHECK is you have entered and will need to re-enter the data. incorrectly 9. are displayed, Press POWER to switch your DVD+VCR to Timer Standby mode. The timer will appear in the display window while your DVD+VCR waits to make the symbol ( ) recording. 10. Press POWER to end timer recording. Notes: The DVD+VCR will Timer power off when ends. Recording During automatically timer recording standby mode, the DVD cannot be operated. To use the VCR mode and DVD+VCR, press POWER. After you use the DVD or VCR, press POWER again to put the VCR into timer If at mode. recording standby later date you wish to delete or change any of the settings in timer event memory you may do so a without mation Use v delete having to enter all the timer event inforagain. Simply display the timer event screen. or or V to select the event that you wish to change. Press b to delete the event...or Press OK to then press b or B to Start and End times and change; Station, Date, Press v recording speed. or select; V to enter the correct information. If Timer record events Make ing sure Overlap... that the events do not preset times of the timer recordoverlap. If they do, the earlier pro- gramme will always Example: Programme 1 is be given priority. programmed to start at 16:00 and programmed to start at 16:30 and end at 17:00. Programme end 2 is at 17:30. (In this case, Programme 1 will be recorded in its entirety, but only the last 30 minutes of Programme 2 will be recorded.) To watch a DVD while performing press DVD to select DVD mode. 26 a timer recording, Playing a DVD or General Features Video CD Note: Playback Setup Turn 1. on the TV and select the video connected to the DVD Turn 2. the on the audio input source input source player. system (if applicable) and select connected to the DVD player. Press OPEN/CLOSE to open the disc tray and load your chosen disc in the tray, with the 3. side down. playback Press OPEN/CLOSE to close the 4. starts automatically. If playback tray. Playback does not start, press N. In some cases, the disc menu might Unless stated Moving to another TITLE When disc has a title/chapter you want to view, then press ENTER to start. Press TITLE or DISC MENU to return to the menu screen. and stopped then the b / B to move You (See on page ? can title operating 21). another ? To watch a The region code for this is 5 more disc has than one chapter/track Press . than more track, you one chapter can move or a to follows: as briefly during playback to select the next chapter/track or to return to the beginning of the current chapter/track. ? Press ous or > . twice briefly to step back to the previ- chapter/track. To go directly to any chapter during DVD playback, press DISPLAY and press v / V to select the chapter/track icon. Then, input the chapter/track numberoruseb/B. Search 1. Press m or M during playback. 2. Press m or M repeatedly to select the required speed. DVD during timer DVD, DivX disc; X2, X4, X16 Video CD; X2, X4 or X8 recording standby mode, press POWER and DVD mode. player on a ? ? DVDs may have a region code. Your player does not play discs that have a region code different from a disc has parental control is set and the disc is not within the rating settings you must input the password. (See "Lock Menu" on page 22.) player. (five). its number while When If your to to another title. to another CHAPTER/TRACK Notes: ? can move playback is appropriate number (0-9) or use Moving may differ. Follow the instructions on the each menu screen. You also may set PBC to "PBC" title, you one play any title by inputting playback is stopped. procedures Off than another title. Press DISPLAY while Use the number buttons to select the track you want to view and press RETURN to return to the settings more appear Use the b B v V buttons to select the Menu use the remote control. Some features may also be available on the Setup menu. instead: menu screen. otherwise, all operations described to switch to DVD 3. To exit SEARCH Changing X100 mode, press N. the Audio Channel Press AUDIO different or repeatedly during playback to hear audio channel (Stereo, Left, or Right). a 27 Still Picture and Frame-by-Frame Playback Repeat You Press PAUSE/STEP 1. the remote control during playback. Advance the picture frame-by-frame by pressing PAUSE/STEP repeatedly. To exit still motion 2. on mode, title/chapter/all/track on a disc. REPEAT during playback to select a desired play can Press a repeat mode. DVD Video Discs press N. ? Slow Motion Repeat Chapter/Title/Off Chapter: repeats the current chapter. ? Title: ? Off repeats the does not : - current title. play repeatedly. Video CDs, Divx discs Repeat Track/All/Off ? Track : repeats the current track - Press PAUSE/STEP 1. The DVD Use m 2. player or (X) during playback. will now M to select the 1/16, t 1/8, t 1/4, 1/16, T 1/8, T 1/4, With go into PAUSE mode. or t or T required speed: 1/2 (backward), or 1/2 (forward). t T discs, Video CD, the Slow speed changes: T 1/16, T 1/8, T 1/4 or T 1/2 To exit Slow Motion playback in reverse is not with possible Video CDs and DivX Discs. If you press > once during Repeat Chapter playback, the repeat playback cancels. The unit in mode. during playback stop automatically begins random playback or and RANDOM appears Press RANDOM again To produce a 3D surround effect that simulates the TV on 1. Press DISPLAY 2. Use 3 screen. or to normal. 3. during playback. 4 to select the sound The sound option will be option. highlighted. Use1or2totoselect"3DSUR". To turn off the 3D Surround Tip: By pressing another title > during random playback, the unit selects (track) and resumes random playback. Note: Video CD with menu to use PBC, You must set PBC to Off the random function (See on "PBC" on the 1. playing at any chosen time box shows the 2. on Press DISPLAY page 21). effect, select "Normal". Time Search To start setup (Track) speakers (instead of the five+ speakers normally required for multi-channel audio from a home theater system). Press RANDOM a play repeatedly. multi-channel audio from two stereo Random On does not : 3D Surround Slow motion 2. Off disc. on a mode, press N. Note: 1. ? repeats all the tracks : Notes: ? (forward). 3. All ?OnaVideoCDwithPBC,youmustsetPBCtoOffonthe setup menu to use the repeat function (See "PBC" on page 21). Divx a ? the disc: during playback. The elapsed playing time. time search Press v / V to select the time clock icon and "-:--:--" appears. Repeat To 1. 2. 3. 28 A-B repeat a 3. starting point. again at your chosen "A B" appears briefly on the TV repeat sequence begins. again " A * required start time in to cancel. end 4. point. screen and the hours, minutes, and If you enter the wrong numbers, press CLEAR to remove the numbers you entered. Then input the correct numbers. " screen. Press A-B Press A-B the seconds from left to sequence. Press A-B at your chosen appears briefly on the TV Input right. Press ENTER to confirm. selected time. Playback starts from the Zoom Use 1. to zoom the video enlarge Press ZOOM image. during playback still or playback to 1600% size screen → fit mode → the can 100% size when screen zoomed 4. To through normal playback, press ZOOM repeat- ? may appear. menu, the Otherwise, the disc screen. offers features such subtitle a angles, as camera options, and Press TITLE to exit. 3. press CLEAR button. or Disc Menu Notes: ? menu spoken language and chapters for the title. the picture. resume edly move appears menu on the menu The 2. Use the bBvVbuttons to corresponding number or use the b to highlight your selection. Then press Press TITLE. If the current title has Normal, Enhanced, and Maximum. 3. the ENTER. 1. image appears on you're playing a DVD movie. Press 3/4 to select between Input Title Menu the way the change the contents of DVD discs: Menus B v V buttons Screen fit mode: You Checking MENU. Each press of the ZOOM button changes the TV screen in the sequence: 100% size → 400% size → DVD Features DVDs may offer menus that allow you to access special features. To use the disc menu, press DISC activate the Zoom function. The square frame appears briefly in the right bottom of the picture. 2. Special Zoom may not work on some DVDs. Screen fit mode is available for playing the DVD Press DISC MENU and the disc Press DISC MENU again is menu displayed. to exit. disc, VR disc and movie file. Camera Marker Search Angle If the disc contains To enter You Marker a start can from up to nine memorized marker, press MARKER at the desired point the TV screen a angles, you can change to a different camera angle during playback. Press ANGLE repeatedly during playback to select a desired angle. Note that the number of the current angle appears on the display. camera playback To enter points. recorded at different scenes the disc. The Marker icon appears briefly. Repeat to enter up to nine on on markers. To Recall 1. 2. or Clear During disc search menu Within 10 a Marked Scene press SEARCH. The marker appears on the screen. playback, seconds, press b / B to select number that you want to recall 3. Press ENTER and marked Changing scene. playback or a You clear. starts from the Or, press CLEAR and the marker on any marker by the marker search menu. can play inputting Language Press AUDIO different repeatedly during playback audio language or audio track. to hear a marker number is erased from the list. 4. the Audio its number Subtitles Press SUBTITLE the different repeatedly during playback subtitle languages. to see Note: ? The subtitle file of the DivX file is smi, ? displayed only srt and sub. If there is no information not read in the DivX file, or " 1 there is " or etc. a code that are can displayed. 29 Playing Audio CD an or MP3/WMA MP3 / WMA disc limited Disc ? as compatibility with this player is follows: within 8 48 kHz (MP3), Sampling frequency: within 32 48kHz (WMA) Bit rate: within 8 320kbps (MP3), 32 192kbps (WMA) The player cannot read an MP3/WMA file that has a file extension other than ".mp3" / ".wma". CD-R physical format should be ISO 9660 If you record MP3 / WMA files using software that cannot create a file system (eg. Direct-CD) it is impossible to playback MP3 / WMA files. We recommend that you use Easy-CD Creator, which - - The DVD player can play MP3/WMA formatted recordings on CD-ROM, CD-R, or CD-RW discs. ? - - ? Audio CD Once you insert an audio CD a menu appears on the TV screen. Press v / V to select a track then press N ENTER and or playback ? ? starts. AUDIO CD 1/12 0:52:07 List Program creates Track1 an Track2 ? Track3 Track4 File names and must Track5 Track6 ? Track7 Clear All Track8 PROGRAM They ISO 9660 file system. should have a incorporate an should not contain maximum of 8 letters .mp3 or .wma extension. special letters such as / ?*:"<>letc. Edit ? The total number of files on the disc should be less than 650. MP3 / WMA 1. Press v / V to select to 2. folder, and press ENTER a the folder contents. see player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. Pre-recorded DVDs are automatically set to these standards. There are Pressv/VtoselectatrackthenpressNor ENTER. Playback starts. many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and MUSIC 0:00:00 This DVD 1/12 these List require certain pre-existing conditions (see above) to ensure compatible playback. Program 1-Music1 2-Music2 Customers should note that 3-Music3 4-Music4 required 5-Music5 6-Music6 DISPLAY Info PROGRAM Edit should ID3 TAG ? When track owner. playing titles, you If there is the containing information such as the information by pressing [ Song, Artist, Album, Comment, Genre ] DISPLAY. ? file a no can see information, "No ID3 TAG" appear on menu screen. Tip: ? If you are in a file list return to the Folder on list, the MUSIC menu the v / V to use and want to and highlight press ENTER. ? Press DISC MENU to ? On ? CD with MP3/WMA and JPEG you can switch MP3/WMA and JPEG. Press TITLE and MUSIC or a PHOTO word on When a playing titles, you 30 to the next page. move top of the file can see menu containing is highlighted. information such the information is in order to download MP3 / WMA files and music from the Internet. Our company has no right to grant such permission. Permission Clear All 7-Music7 permission by pressing as track DISPLAY. always be sought from the copyright Audio CD and MP3 / WMA Disc Random Features 1. Pause 1. 2. Press PAUSE/STEP press Moving 1. playback, press PLAY, PAUSE/STEP again. ENTER or or the next track > to or 2. To return to normal until repeatedly playback, press RANDOM RANDOM disappears from the menu screen. Tip: to another Track Press . during playback or when playback is stopped. Random Playback begins immediately and RANDOM appears on the menu screen. during playback. To return to Press RANDOM briefly during playback to go to return to the beginning of the By pressing > during another track and random resumes playback, the random playback. unit selects current track. 2. Press . twice briefly to go back to the Repeat previous track. 3. In case of audio CD, Repeat You 1. can 1. To 2. Press A-B again at your chosen end point. The Repeat icon and "A-B" appear on the menu screen, and the sequence begins to play repeatedly. 3. To exit the sequence and return to normal play, press A-B again. The Repeat icon disappears from to go enter the track number buttons directly to any track, using the numbered (0-9). Track/All/Off play a track/all on a Press REPEAT when disc. playing a disc. The repeat icon appears. 2. ? ? ? a desired does not To repeat playback during Repeat Track menu screen. playback, produce a 3D surround effect that simulates multi-channel audio from two stereo speakers (instead of the five+ speakers normally required for multi-channel audio from a home theater system). play repeatedly. Note: once a 3D Surround repeats the current track All: repeats all the tracks on a disc. Off(No display): repeat repeat mode. Track: If you press > sequence during disc playback press A-B at your chosen starting point. The Repeat icon and "A" appear on the menu screen. the Press REPEAT to select A-B the cancels. 1. Press AUDIO during playback. "3D SUR." appears 2. Search Press m or M during playback. 2. Press m or M repeatedly speed: X2, X4, 3. X8 To exit SEARCH to select the backward or the menu screen. To return to normal repeatedly 1. on until playback, press AUDIO "3D SUR." disappears from the menu screen. required forward. mode, press N. 31 Repeat Programmed Programmed Playback 1. A program 1. Insert 2. memory. contain 30 tracks. can a player Press REPEAT when Press REPEAT to select ? disc. ? ? Audio CD or MP3/WMA Discs: AUDIO CD or MUSIC menu appears. 2. mark will appear to the right of the word "Program" on the right side of the menu screen. Note: disappear to exit the 0:52:07 1. mark will MUSIC List E Program Track1 Track5 Track2 Track7 1-Music1 4-Music4 Track3 Track4 2-Music2 6-Music6 Track4 Track1 3-Music3 1-Music1 2-Music2 4-Music4 Track6 5-Music5 Track7 6-Music6 Clear All Track8 E Program Track5 Clear All 7-Music7 DISPLAY Audio CD Menu PROGRAM Info setup to menu "PBC" on the use must set PBC to Off on programmed playback E Program Track1 Track5 Track2 Track2 Track3 Track3 Track4 Track1 Track5 Clear All Video CD Menu 3. Select a track on the "List", then press ENTER to place the selected track on the "Program" list. Repeat to place additional tracks on the list. 4. Press B. Select the track you want to start "Program" list. 5. Press N or playing list have To normal resume playback, select a played on the once. playback from track of CD and then press N. 32 the Playback begins in programmed the tracks. the order in which you Playback stops after all of the tracks 6. on ENTER to start. "Program" Program stop mode to Edit mode. move to the "Program" list. Repeat to erase erase additional tracks the list. the Follow Complete Program as steps programmed (or MP3/WMA) list 1-2 of "Erasing a List Track from Program above. Use 3/4 to select "Clear complete Program All", then press ENTER. for the disc will be erased. Note: The programs removed. VIDEO CD List Press PROGRAM in the Press CLEAR. 2. 21). page : 4. List" Note: the the List Program Use v/V to select the track that you wish to from the "Program" list. Erasing menu. PBC, you during Repeat Track playback, 3. The Video CD with once Press B to Video CD: Press PROGRAM while playback is stopped. The program menu appears. Press a play repeatedly. 2. 1. On repeat mode. Edit MP3/WMA Menu PROGRAM to exit the does not Track from a Video CD on PROGRAM Edit desired 1/12 0:00:00 1/12 List (See Off(No display): enter Edit mode. AUDIO CD a repeats the current track All: repeats all the tracks on programmed list. Erasing again, then the Program repeat repeat playback cancels. E Press PROGRAM disc. The Track: If you press > E a Note: Press PROGRAM. The playing icon appears. The program function enables you to store your favorite tracks from any disc in the Tracks are also cleared when the disc is Viewing this DVD Using JPEG Disc a Player you can Moving view discs with JPEG files. 1. Insert disc and close the a the TV on appears tray. The PHOTO menu screen. Press.or>orcursorborBoncewhile Use (see Preview List JPEG Folder 1 to advance to the next viewing a picture previous file. or JPEG Zoom PHOTO JPEG to another File the to enlarge page) zoom 29 photo image. JPEG Folder 2 >>> JPEG Folder 3 To rotate JPEG Folder 4 JPEG Folder 5 picture JPEG Folder 6 Press v / V JPEG Folder 7 during showing JPEG Folder 8 picture clockwise or a counter clockwise. To listen to MP3/WMA music 2. Press v / V to select a folder, and press ENTER. A list of files in the folder appears. If you are in a file list and want to return to the previous Folder list, the v / V buttons use the remote to and press ENTER. highlight 3. on Viewing the file proceeding starts. While viewing a file, you can press STOP to the previous menu (PHOTO menu). Slide Show to N. the (Slide Show) (Normal) ? On then ? > Speed options (Slow). (Fast), : >>> Press TITLE to 3. Press v / V to select 4. Use B / V to select on top of the 2. player display a PHOTO photo menu. file. pressed. menu is >> limited ? highlighted. compatibility now during slide show. follows: as upon the size and number of JPEG files, it could take a long time for the DVD player to read the disc's contents. If you don't see an Depending 2048 go into PAUSE mode. To return to the slide PAUSE/STEP is player display after several minutes, some of --- JPEG will with this the files may be too large reduce the resolution of the JPEG files to less than 2M pixels as 2760 x Press PAUSE/STEP The Operation types of file in icon then press ENTER. starts. The playback will continue until on-screen 1. the two Tip: RETURN, information of file is hidden. Still Picture containing 2. JPEG disc disc with MP3/WMA and JPEG you can switch MP3/WMA and JPEG. Press TITLE and MUSIC or Press disc. same only the desired music watching picture, programmed the desired tracks from the "MUSIC" menu and then proceed as above. a PHOTO word the to MP3/WMA To listen to three Slide and on listening player. STOP is highlight files while Insert the disc Playback Tip: are display move press ENTER. There can music files recorded JPEG Use vVbBto ? You the or watching picture JPEG 1. If you want to view a particular file, press v / V to highlight a file and press ENTER to rotate the picture show, press N or ? press pixels and burn another disc. The total number of files and folders the disc on should be less than 650. again. ? Some discs may be incompatible due to a different recording format or the condition of disc. ? Ensure that all the selected files have the extensions when ? into the CD If the files have rename ? copying ".jpg" layout. File them names ".jpe" or ".jpeg" extensions, please as ".jpg" file. without able to be read the files are Windows by shown ".jpg" extension will not be this DVD+VCR. Even as JPEG image though files in Explorer. 33 DVD VR format Disc Playing a This unit will play DVD-R/RW discs recorded the DVD-Video format that have been a ? Refer to the information in this contacting This unit will play DVD-RW discs recorded using Recording (VR) format. Insert a disc and close the menu appears on the TV tray. The DVD-VR screen. DVD-VR When Please shipping save Do not Pressv/VtoselectatrackthenpressNor ENTER and playback starts. move to the list menu. use near volatile liquids such as insecticide the unit. plastic products in contact long period of time. since they or with the unit for a leave marks the surface. Cleaning on the unit To clean the Note: Unfinalized DVD-R/RW discs cannot be played in this player. ? the Do not leave rubber ? Press TITLE to the unit the exterior surfaces clean spray ? service technician. original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. ? 3. before the Unit Handling Keeping 2. a chapter DVD-recorder. the Video 1. using finalized using Maintenance and Service Some DVD-VR disc RECORDER. are Player made with CPRM data does not by DVD support these kinds of discs. player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not or use thinner, strong solvents such as these as might damage alcohol, benzine, the surface of the unit. What is 'CPRM'? CPRM is only scramble copy protection system (with system) allowing the recording of 'copy once' broadcast a programs. CPRM stands for Content Protection for Recordable Media. This player is CPRM compatible, which means that you record copy-once broadcast programs, but you cannot then make a copy of those recordings. CPRM recordings can can only be made on DVD-RW discs formatted in VR mode, and CPRM recordings players that are only specifically compatible can be played on with CPRM. Maintaining the Unit The DVD player is a high-tech, precision device. optical pick-up lens and disc drive parts are dirty worn, the picture quality could be diminished. or Depending on the operating environment, regular inspection and maintenance are recommended after every 1,000 hours of For details, please service center. 34 If the use. contact your nearest authorized Playing a DivX Movie Disc DivX disc as this DVD Using Insert 1. a appears Player you can disc and close the on the TV play compatibility with this player is limited follows: DivX disc. ? tray. The MOVIE menu Available resolution size of the DivX file is under 720x576 (W x H) pixel. screen. ? The file name of the DivX subtitle is available by 56 characters. MOVIE 0:00:00 List ? Movie Folder 1 If there is impossible code to file, it may be displayed as display. " Movie Folder 2 Movie Folder 3 Movie Folder 4 Movie Folder 5 express in the DivX mark on the " _ Movie Folder 6 Movie Folder 7 ? Movie Folder 8 If the number of the screen frame is over 30 per 1 second, this unit may not operate normally. Press v / V to select 2. a folder, and press ENTER. ? A list of files in the folder appears. If you are in a file list and want to return to the Folder list, use the v / V buttons on the remote to If the file is recorded with * or N. move On is CD with highlighted. Operation are called 1-point, 2-point, or Xvid, have this option. different levels of GMC or 3-point encoding, usually GMC. to the next page. MP3/WMA, JPEG and MOVIE file, you can switch MUSIC, PHOTO and MOVIE menu. Press TITLE and MUSIC, PHOTO and MOVIE word on top of the menu a encoders, like DivX There Playable ? GMC, the unit GMC is the acronym for Global Motion Compensation. It is an encoding tool specified in MPEG4 standard. Some MPEG4 Press STOP to exit. Press DISC MENU to audio is GMC? Tip: ? or supports only 1-point of the record level. If you want to view a particular file, press v / V to highlight a file and press ENTER 4. interleaved, either video outputted. ? press ENTER. 3. file is not and highlight If the video and audio structure of recorded DivX file z ".avi ", ".mpg ", ".mpeg Playable Codec format " z "DIVX3.xx ", "DIVX4.xx ", "DIVX5.xx ", "XVID ", "MP43 ", "3IVX ". Playable Audio format z "AC3 ", "DTS ", "PCM ", "MP3 ", "WMA ". ? Sampling frequency: within 8 48 kHz (MP3), - within 32 ? Bit 32 48kHz (WMA) rate: within 8 320kbps (MP3), 192kbps (WMA) - - - 35 Additional Features-VCR On Screen You may part Video Doctor Display the current time easily display tape or counter, amount of tape left, day, month, year, day of programme channel, tape speed and operational mode of your VCR will appear on the TV screen. If a recording is taking place these On Screen week, Displays will not be recorded onto the This feature informs you that there is a problem with your DVD+VCR. These error messages will appear on the TV screen. 1. Press i. Press1or2toselect . Press OK. tape. Press CLK/CNT to 1. display. repeatedly Press CLK/CNT display options. The tape to cycle through a counter and the amount of Press CLK/CNT the TV to again PSET R tape loaded. majority of the leaving only the will clear 12 Pr-12 After 3 seconds the Displays the counter and amount of tape left will appear if there is 2. (Self-Diagnosis) SET SYS fOSD ON OFF On Screen clock tape left remove ACMS the on all or tape screen. displays ANTENNA CONNECT from HEAD STATUS TAPE STATUS NO. OF TIMER PROGRAMME screen. NEXT TIMER PROGRAMME PLEASE CHECK Tape Counter Memory Stop The i displayed on the the time by pressing CLK/CNT on the remote control. The Digital Tape Counter indicates the relative positions of recordings Digital Tape Counter display window instead of on 1. the can be 2. Press CLEAR to set the counter to 0:00:00. start The recording. will display Press STOP when problem. playback or recording is NEXT TIMER PROGRAMME O PR-01 26 10:00~11:00SP Shows the current status of timer Press BACKWARD. tape will rewind and automatically stop when the counter returns to 0:00:00. 3. Lock (Child Lock) The control buttons switched off using 1. on the front of the unit that your unit the remote control. so can only be can be operated Press LOCK. and SAFE will appear in the display window. None of the buttons on the front of your unit will work. If any buttons on the front of your unit SAFE will flicker in the display are window for pressed a few seconds. 2. 36 jack securely. Press LOCK to switch off the child lock. OFF will in the again disappear display window. place NO. OF TIMER PROGRAMME O2 Shows the number of timer recording. complete. The a TAPE STATUS O NOT RECORDABLE: Insert a tape with its protection tab in the actual play time tape counter in hours, minutes and seconds. 2. to check HEAD STATUS O PLEASE CLEAN: Clean your video heads. Press CLK/CNT. or 3 or 4 ANTENNA CONNECT O PLEASE CHECK: Connect the aerial into the tape. Press N Press Press i to remove the menus recording. from the TV screen. Hi-Fi Stereo Sound System Your VCR will record and playback sound. In addition it has stereo NICAM a Hi-Fi stereo 12 stereo digital and playback PSET R sound decoder. This allows you to record the sound in several different ways. Video cassettes recorded your VCR will have a normal mono audio track and two VHS Hi-Fi stereo audio tracks. These stereo audio system, video disc Your VCR's NICAM SET ACMS SYS PSET R fOSD AUTO A S 4:3 16:9 fOSD ON OFF or 2. ON OFF i recorded will be another Hi-Fi VCR. Automatically plays the TV on screen stereo and mono programmes as Wide-Screen and Normal programmes 4:3 as normal. Only recorded automatically tracks of the video and recording for format the Hi-Fi on AUTO, 4:3 or Normal format 16:9: STEREO NICAM Sound is to select: back Wide-Screen Only for playing back recordings (4:3). of seconds: couple a briefly displayed repeatedly AUTO: sound decoder allows digital Press v/V 16:9. you to enjoy broadcasts with NICAM sound, as well as standard stereo, bilingual and mono sound. The particular type of sound received or that for Pr-12 on stereo tracks allow you to make audio recordings in Hi-Fi stereo or bilingual mode from a TV broadcast, 1. 12 Pr-12 playing back and recording recordings (16:9). Wide-Screen Operation tape. BIL NICAM Both audio channels will be recorded stereo tracks. The will be recorded primary language on the mono on the Hi-Fi channel 12 (left) Pr-12 AUTO S PSET R track of the video 4:3 16:9 fOSD ON OFF i tape. MONO The sound is recorded mono 2. track of the video Press AUDIO the Hi-Fi tracks and the on 3. To tape without any separation. repeatedly The choice is MONO. playback the primary lan- guage is output on the left channel and the secondary channel is output simultaneously from the right channel when audio output is set to STEREO. The primary language willbe output from both setting is MONO. adjusting the tracking control Hi-Fi stereo sound may revert to MONO. Your DVD+VCR can record and of wide format programme screen signal Switch on Wide-Screen playback you must the TV using a SCART-SCART already described, how to connect a decoder for pay-TV station as CANAL+ or PREMIERE on page 10. For the recording of an encoded station you do not have to control anything. You just select the station and wait shortly until the decoding will 1. Press i. The main play back wide successfully a screen must be broadcast by 2. your DVD+VCR. Press D ON: wide the correct will appear on the TV screen. G to select the DECODER. menu or Press OK. or E to select. When the decoder is connected to the AV2 socket. type OFF: When another VCR is connected to the AV2 the TV socket. station. 1. screen. We have 16:9 Compatibility aspect ratio programmes (16:9). To record screen from the TV To set the decoder Press F Wide Screen menus start. channels when the audio Please note that when the cable. STEREO, LEFT, RIGHT and In BIL NICAM enjoy remove connect your VCR to until the desired audio mode appears. 3. Press i to 3 Press i to return to a TV Picture. Press i. PressForGtoselect . Press OK. 37 Controlling Additional Features Last Scene This source, and power switch of your LG TV with the supplied remote control. Memory memorizes last player that is viewed. The last scene from the last disc remains in memory the disc from the player or switch scene if you remove off the player. If you load even memorized, the scene is a disc that has the can control the sound level, input You can control the sound level, input power switch of non-LG TVs as is listed in the table below, set the player manufacturer code. 1. does not memorize the player before disc if you to play the disc. scene commencing of in appears when you leave the DVD mode for about five minutes. Stop Video Mode Setting down TV POWER 2. (see the table Release TV POWER button. If more them than one one at a code number is 1 Zenith 1,3,4 Samsung 6,7 not Sony 8,9 perfectly matched with the disc. In this case, the picture quality may be improved by changing the Hitachi 4 video mode. Note: flickering That Dot Crawl is shown or means To Vertical straight on interpolation or lines. De-interlace is the video mode, press and hold change DISPLAY about 3 seconds during disc playback. Video mode sequence: MODE1 → MODE2 → MODE3 → MODE1 : The video MODE2 : Description source material) : (film materi- is determined from disc information. Suitable for based material MODE3 of each Video Mode material of the DVD video playing film based content or video recorded by the progressive scan method. Suitable for comparatively playing video based content with little motion. Note: The video mode Progressive menu. setting only works when the Scan mode is set to "On" on the Depending function setup that works on (Default), 2 your TV, some or all buttons may not the TV, even after entering the correct on manufacturer code. ? If you enter a new code number, the code number previously entered will be erased. ? When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the MODE1 If you turn off the power, the video mode will return to initial default state (MODE1). Detailed ? video mode number selected is displayed on the TV screen. Check whether the video quality has improved. If not, repeat the above procedure until picture quality is improved. new one with your TV. LG / GoldStar discs, the playback picture may be listed, try entering time until you find the Code Number or button, press the below). Manufacturer With certain 38 holding Code numbers of controllable TVs screen saver player al While for your TV a Screen Saver The appropriate number buttons to select the manufacturer code switch off the The source, and well. If your TV scene recalled. automatically You Note: This other TVs with the remote control appropriate code number again. from DVD To VCR Copying This unit allows you to copy the contents of a DVD to a VHS tape with a press of the REC/ITR button. Notes: Be sure setup to set Scan" to "Off" on the recorder With this video recorder you can make recordings from an external source, such as copying from another video recorder protected, attempting to copy is copy you may not be able to copy the disc. are 3. Insert Disc Insert the disc you wish to copy in the DVD deck and close the disc tray. Insert VHS Tape Insert a blank VHS In the following description, this video recorder will be one used for recording and will be referred to as VCR B. The other appliance will be used for playback and will be referred to videotape into the VCR deck. the DVD to VHS Tape Press the REC/ITR button. Copy If the DVD disc to press the appears, you may need button manually to begin menu Play the panel panel of rear the front 2. as VCR A. VCR A should be connected to the SCART socket on The DVD will go into Play mode and the VCR will go into Record mode. of your unit your unit. Insert the recorded or the AV sockets tape into VCR A and a on blank tape into VCR B. 3. copying. Press AV until the socket you wish to record from is displayed. (VCR B) AV 1 for recording Note: If you press the REC/ITR DVD mode. button, be sure this unit in the rear the rear from EURO AV1 SCART socket of your unit. AV 2 for recording from EURO AV2 SCART socket on of your unit. AV 3 for recording from VIDEO IN and AUDIO IN on (Left 4. camcorder. Note: 1. 2. or a menu. If the DVD you 1. "Progressive from another video Recording the Copy Process When the DVD is finished end the copy. Stop playing, press STOP to You must stop the Copy process manually when the DVD movie ends, or the unit may replay and record over and over 4. & To start Right) on the front of your unit. press the REC/ITR VCR A. recording, and PLAY 5. sockets on When you want to finish on both video recorders. copying, on VCR B press the STOP again. 39 Reference Language Codes Use this list to your desired language for the Disc Audio, Disc Subtitle, Disc Menu. input Language Code Abkhazian following Code 6566 Language Fiji Afar 6565 Afrikaans initial settings: Code 7074 Language Lingala Code 7678 Language Singhalese Finnish 7073 Lithuanian 7684 Slovak 8375 6570 French 7082 Macedonian 7775 Slovenian 8376 Albanian 8381 Frisian 7089 7771 Somali 8379 6577 Galician 7176 7783 Spanish 6983 Arabic 6582 Georgian 7565 Malagasy Malay Malayalam Ameharic 7776 Sudanese 8385 Armenian 7289 German 6869 Maltese 7784 Swahili 8387 Assamese 6583 Greek 6976 Maori 7773 Swedish 8386 Aymara Azerbaijani 6588 Greenlandic 7576 Marathi 7782 8476 6590 Guarani 7178 Moldavian 7779 Tagalog Tajik Bashkir 6665 Gujarati 7185 Mongolian 7778 Tamil 8465 Basque Bengali; Bangla 6985 Hausa 7265 Nauru 7865 Tatar 8484 6678 Hebrew 7387 7869 Telugu 8469 Bhutani 6890 Hindi 7273 7879 Thai 8472 Bihari 6672 Hungarian 7285 7982 Tibetan 6679 Breton 6682 Icelandic 7383 Nepali Norwegian Oriya Panjabi 8065 8473 Bulgarian 6671 Indonesian 7378 Pashto, Pushto 8083 Tigrinya Tonga Burmese 7789 Interlingua 7365 Persian 7065 Turkish 8482 Byelorussian 6669 Irish 7165 Polish 8076 Turkmen 8475 Cambodian 7577 Italian 7384 Portuguese 8084 Twi 8487 Catalan 6765 Japanese 7465 Quechua 8185 Ukrainian 8575 Chinese 9072 Javanese 7487 Rhaeto-Romance 8277 Urdu 8582 Corsican 6779 Kannada 7578 Rumanian 8279 Uzbek 8590 Croatian 7282 Kashmiri 7583 Russian 8285 Vietnamese 8673 Czech 6783 Kazakh 7575 Samoan 8377 Volapuk 8679 Danish 6865 Kirghiz 7589 Sanskrit 8365 Welsh 6789 Dutch 7876 Korean 7579 Scots Gaelic 7168 Wolof 8779 English Esperanto 6978 Kurdish 7585 Serbian 8382 Xhosa 8872 6979 Laothian 7679 Serbo-Croatian 8372 Yiddish 7473 Estonian 6984 Latin 7665 Shona 8378 Yoruba 8979 Faroese 7079 Latvian, Lettish 7686 Sindhi 8368 Zulu 9085 8373 8471 8479 Area Codes Choose a area Area Code Code Area Code Area Code ET Malaysia MY Saudi Arabia SA AR FJ Maldives MV SN Australia AU Finland FI Mexico MX Austria AT France FR Monaco MC Senegal Singapore Slovak Republic Belgium BE Germany DE Mongolia MN Slovenia SI Bhutan BT Great Britain GB Morocco MA South Africa ZA Bolivia BO Greece GR Nepal NP South Korea KR Brazil BR Greenland GL Netherlands NL Spain ES Cambodia KH Islands HM Netherlands Antilles AN Sri Lanka LK Canada CA HK New Zealand NZ Sweden SE Chile CL Hong Kong Hungary HU NG Switzerland CH China CN India IN Nigeria Norway NO Taiwan TW Colombia CO Indonesia ID Oman OM Thailand TH Congo CG Israel IL Pakistan PK TR Costa Rica CR Italy IT Panama PA Turkey Uganda Croatia HR Jamaica JM PY Ukraine UA CZ JP Paraguay Philippines PH United States US KE Poland PL Uruguay UY Republic AF Area Ethiopia Fiji Afghanistan Argentina Czech 40 code from this list. SG SK UG Denmark DK Japan Kenya Ecuador EC Kuwait KW Portugal PT Uzbekistan UZ Egypt EG LY Romania RO Vietnam VN El Salvador SV Libya Luxembourg LU Russian Federation RU Zimbabwe ZW Troubleshooting Check the following guide for the possible cause or VCR do not problem a before contacting service. Cause Symptom DVD work of DVD or Correction VCR button is not switched Refer to page 2. properly. properly. No power. The power cord is disconnected. the power cord into the wall outlet securely. The power is on, but the DVD player does not work. No disc is inserted. Insert a disc. (Check that the DVD or, audio CD indicator in the display window is lit.) No The TV is not set to receive DVD Select the appropriate video input mode on the TV so the picture from the DVD player appears on the TV picture. signal output. Plug screen. No sound. The video cable is not connected Connect the video cable into the securely. securely. The Progressive Scan is set to "On" on the setup menu but is connected to a standard (analog) television. Set The equipment connected with the audio cable is not set to receive DVD Select the correct input mode of the audio receiver so you can listen to the sound from the DVD player. signal output. The audio cables are not connected picture is poor. The DVD not start does player playback. Turn on the equipment connected with the audio cable. The Set the is set to the The disc is dirty. The TV channels are not tuned in An unplayable properly. disc is inserted. placed upside down. within the placed guide. Video tape properly. cannot be jacks The power of the equipment connected with the audio cable is turned off. The disc is not does not work Connect the audio cable into the securely. The disc is The remote control Scan to "Off" securely. Digital Audio Output wrong position. The Progressive (see page 19). jacks Digital Audio Output to the correct position, then turn on the DVD player again by pressing POWER. Clean the disc. Check tuning, carry out tuning again. Insert a playable disc. (Check the disc type and Regional code.) Place the disc with the down. playback Place the disc on the disc rectly inside the guide. The disc is dirty. Clean the disc. The level is set. Cancel the Rating function the rating level. Rating There is an obstacle in the path of the remote control and this unit. Remove the obstacle. The batteries in the remote control are exhausted. Replace Is the cassette Eject compartment empty? the the batteries with tray or side cor- change new ones. tape in. inserted. No Hi-Fi sound Audio mode is not set No NICAM sound NICAM mode is not set recording properly. properly. Select "STEREO" by repeatedly pressing "AUDIO" on the remote control. Make sure NICAM in the menu is set to AUTO for the station to be recorded. 41 Specification General Power requirements AC Power consumption 17W Dimensions Mass 110-240V, 50/60 Hz 430 X 78.5 X 265 (approx.) 4.2 (approx.) mm (w/h/d) kg Operating temperature 5˚C to 35˚C Operating humidity 5%to90% Timer 24 hours RF Modulator UHF 22 (41˚F to 95˚F) display tape 68 - (Adjustable) System Laser Semiconductor Video Head laser, wavelength Double azimuth 6 system 650 heads, helical scanning. Signal system PAL Frequency DVD(PCM96kHz):8Hzto44kHz DVD(PCM48kHz):8Hzto22kHz response nm CD:8Hzto20kHz ratio Signal-to-noise More than 100dB (ANALOG Harmonic distortion Less than 0.008% Dynamic More than 100 dB range More than 95 dB OUT connectors only) (DVD) (CD) Inputs (VCR) Audio Video -6.0dBm, -6.0dBm, more than 10 kohms more than 47 kohms 1.0 75 Vp-p, (SCART) (RCA) ohms, unbalanced (SCART/RCA) Outputs (DVD) VIDEO OUT 1 Vp-p 75 ohms, sync negative (Y) 1.0 Vp-p 75 ohms, negative (C) 0.3 Vp-p 75 ohms S-VIDEO OUT COMPONENT VIDEO OUT sync., Mini Din (Progressive Scan) (Y) 1.0 V (p-p), 75 Ω, negative sync, RCA jack (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2 RGB 0.7 output 4-pin x x 1 1 75 ohms Vp-p, Audio output (digital audio) 0.5V(p-p),75Ω,RCAjackx1 Audio output (optical audio) 3 V Audio output (analog audio) 2.0 Vrms (p-p), 75 Ω, Optical (1 KHz, 0 dB), connector x 1 600 Ω, RCA jack (L, R)x2/SCART (TO TV) Outputs (VCR) Audio -6.0dBm, less than Video 1.0Vp-p, RGB 0.7 output Design and specifications are Manufactured under license from "DTS" and "DTS 42 Digital Out" are subject Dolby to Vp-p, change Laboratories. trademarks of Digital 75 1 kohms (SCART) ohms, unbalanced (SCART) 75 ohms without notice. "Dolby" Theater and the double-D Systems, Inc. symbol are trademarks of Dolby Laboratories. P/NO : 3834RV0036S
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021