LG BN315, BN315-JD Owner's manual

LG BN315, BN315-JD Owner's manual
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the bottom of the set and
quote this information to your dealer when you
require service.
Model number
:
Serial number
:
LGDPROJECT
BN315-JD
OWNER'S MANUAL
DLP PROJECTOR
FCC NOTICE
?
A Class B
This
digital device
equipment has been
tested and found to
to Part 15 of the FCC Rules. These limits
interference in
a
comply with the limits for a Class B digital device, pursuant
designed to provide reasonable protection against harmful
equipment generates, uses and can radiate radio frequency
are
residential installation. This
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this
equipment does cause harmful interference to radio or television reception, which can
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
be determined
-
-
-
-
?
Warning
This is
which
a
class B
case
the
product.
user
In
may be
a
domestic environment this
required
to take
adequate
product
measures.
may
cause
radio
interference, in
Contents
Contents
Safety
Instructions....................................4
Names of
parts
Main
Body .......................................................7
Connecting Part ..............................................7
Control Panel ..................................................8
Remote Control ...............................................9
Installing
Projector
Batteries ...........................................9
Status Indicators ..............................10
Accessories .....................................................11
Optional
Extras ...............................................11
Installing
and
Composition
Installation Instructions ...................................12
Basic
Operation of the Projector .....................13
Using Kensington Security System.................14
Turning on the Projector .................................15
Turning off the Projector .................................15
Focus and Position of the Screen Image........16
Selecting source mode ...................................16
Special Menu Options
Selecting Language ........................................22
Using ARC Function........................................22
Flip horizontal Function ...................................23
Flip vertical Function .......................................23
Auto sleep Function ........................................23
Using Keystone Function ................................24
Using Blank Function ......................................24
Selecting Blank image color ...........................24
Lamp mode Function ......................................25
Checking lamp time ........................................25
Using Still Function .........................................25
Screen Menu
Connection
Connecting
Connecting
Connecting
Connecting
Connecting
PC ..........................17
to
a
to
a
Notebook PC ........................17
to
a
Video Source ........................17
to
a
DVD ......................................18
to
a
D-TV
Desktop
Set-Top
Options
Configure Function .................................26
Manual configure ............................................26
Using ZOOM Function ....................................27
Auto
Screen Position ...............................................27
Reset
(Reset
to
original factory value)............27
Information
Supported
Monitor
Display..............................28
Maintenance....................................................28
Replacing the Lamp ........................................29
Specifications ..................................................31
Box ................18
Function
Video Menu
Options
Adjusting Video ...............................................19
APC (Auto Picture Control).............................19
Auto Color Temperature Control .....................20
Gamma Function ............................................20
White
peaking
Color
temperature Control
Function ..................................21
..............................21
Color enhancement Control ............................21
Reset
(Reset
to
original factory value)............21
Disposal
of your old
appliance
1. When this crossed-out wheeled bin
symbol
is attached to
a
product
it
the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
means
appointed by the government or the local authorities.
disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
3. The correct
4.
3
Safety
Instructions
Instructions
Safety
Please take note of the
Instructions
Safety
WARNING
NOTES
After
safety
:
:
are
instructions to
given
prevent any potential accident
in two forms
as
The violation of this instruction may
this
projector.
detailed below.
The violation of this instruction may
reading
misuse of the
or
serious
cause
cause
light injuries
manual, keep it in the place that the
user
and
injuries
or
always
even
damage
can
death.
to the
contact
projector.
easily.
WARNING
Do not place the Projector in direct
sunlight or near heat sources such
as
radiators, fires and
This may
place
inflammable materi-
Do not allow children to
the installed
projector
stove etc.
This may
fire hazard !
cause a
Do not
als beside the
It may
fire hazard !
cause a
cause
ing injury
or
hang
on
projector.
the
projector to fall,
caus-
death.
NOTES
Disconnect from the mains and
all connections before
remove
moving.
Do not
to
place
sources
the
projector
of steam
or
the
installing
the
projector
place
not to
Only
it
and stable surface.
edge.
adult and serious
damage
place the projector where
be exposed to dust.
projector
It may fall and cause
to the unit.
on a
injury
level
This would
or
Ensure good ventilation around the
projector. The distance between
the projector and the wall should
and/or
be
damage
more
than 20cm/8 inches.
An excessive increase in its internal
damage
a
fire hazard
cause a
to the unit!
temperature may
cause a
fire hazard
or
to the unit!
suitable stand.
Do not block the vents of the proor restrict air-flow in any way.
cause
the internal temperacause a fire
ture to increase and could
or
use
damage
or an
to the
jector
hazard
the
on a
This may cause the projector to fall
causing serious injury to a child or
projector.
Only use
might
This may
table, be careful
near
Do not
it
humidifier.
as a
This may create a fire hazard
electric shock hazard !
When
close
oil such
damage
Do not
place
the
projector directly
on a
carpet, rug
or
place
where
ventilation is restricted.
This would
hazard
or
cause
damage
its internal temperature to increase and
the unit.
might
create
a
fire
to the unit!
WARNING
Do not
use
This may
the
cause a
projector
fire
or an
in
a
damp place
such
as a
bathroom where it is
likely
to
get
wet.
electric shock hazard !
WARNING
Earth wire should be connected.
If the earth wire is not connected, there is a
possible danger of electric shock caused by
the current leakage.
If grounding methods are not possible, a
separate circuit breaker should be installed
by a qualified electrician.
Do not connect ground to telephone wires,
lightning rods or gas pipe.
4
The mains
plug
should be inserted
into the power outlet to avoid
fire hazard !
fully
This may
the unit.
cause a
fire hazard
or
a
damage
Do not
place heavy objects
on
the power cord.
This may cause
shock hazard !
a
fire
or an
electric
Safety
Instructions
WARNING
Do not
use
too many
It may result in
plugs
overheating
the Mains multi-outlet.
on
of the outlet and
fire hazard !
causes a
NOTES
Never touch the power
wet hand
plug
with
Hold the plug firmly when unplugging. If you pull the cord, it may
be damaged.
a
This may
hazard !
cause an
electric shock
This may
Do not
or
plug when the power cord
plug is damaged or any
the
cause a
Ensure the power cord does not
into contact with sharp or
part of the power outlet is loose.
hot
This may cause
shock hazard or
fire
a
damage
Do not turn the
(Do
not
It may
electric
to the unit!
objects
projector On/Off by plugging-in
plug for switch.)
such
or
a
This may
cause a
the
fire hazard !
as a
fire
heater.
or an
damage
projector where people
trip or tread on the power
lead.
electric
This may cause
shock hazard or
to the unit!
unplugging
Place the
will not
the power
plug
a
fire
or an
damage
electric
to the unit!
to the wall outlet.
the power
use
cause
or an
collecting on
plug pins or outlet.
fire hazard !
come
This may cause
shock hazard or
Prevent dust
power
mechanical failure
or
could
cause an
electric shock.
WARNING
Do not place anything containing
liquid on top of the projector such
as flowerpot, cup, cosmetics or
In
candle.
of
impact
fire hazard
cause a
dam-
This may cause
shock hazard or
a
doctor
lens
any
In the
or an
to fall
objects
projector.
This may cause an electric shock
hazard or damage to the unit!
electric
to the unit!
batteries
In the event that
care-
image does
please
switch it off and unplug it from
the mains supply and contact
your Service Agent.
not appear
of a battery being
by a child please consult
immediately.
case
swallowed
a
on
This may cause
shock hazard or
covers
cover). High
fire
damage
This may cause an electric shock
hazard or damage to the unit!
remove
cen-
Do not allow any
into the
or
to the unit!
Dispose of used
fully and safely.
Do not
or
ter.
If water is spilt into the projector
unplug it from the mains supply
outlet immediately and consult
your Service Agent.
(except
shock
let and contact your service
This may
damage
case
age to the projector switch it off
and unplug it from the mains out-
risk of
Electric Shock!
an
the
a
screen
fire
Don't look
onto the lens
Do not touch metal
when the
is in
soon
damage
directly
projector
use.
Eye
after
vents and
may occur!
or an
damage
electric
to the unit!
parts during
operation
lamp cover
since
or
the
will remain
very hot!
CAUTION
concerning the Power Cord
appliances recommend they be placed upon a dedicated circuit; that is,a single outlet circuit which
powers only that appliance and has no additional outlets or branch circuits.Check the specification page
Most
of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets,loose
or
damaged
wall
outlets, extension cords,
power cords,or damaged or cracked wire insulation are dangerous.Any of these conditions could
result in electric shock or fire. Periodically examine the cord of your appliance,and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced
frayed
with
an
exact
replacement part by
an
authorized service
personnel.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the
cord exits the
appliance.
5
Safety
Instructions
WARNING
Never touch the wall outlet when
Do not
drop
there is
impact
shock.
of gas, open the
windows and ventilate.
leakage
This may
the
or
allow
Don't look at laser beam directly
it can cause eye damage!
as
cause
personal injury
Itcancauseafireoraburnbya
spark.
projector
mechanical failure
or
!
NOTES
Do not
top
of
place heavy objects
projector.
This may
cause
Take
on
mechanical failure
not to
care
particularly
projector.
or
when
impact the lens
moving the
Do not touch the lens of the prois delicate and easily
jector. It
damaged.
personal injury!
Do not
use
any
sharp
tools
the
on
projector
as
this will
damage
the
casing.
WARNING
Do not
the
use
water while
cleaning
projector
This may
projector
cause
or an
damage
In the
of smoke
a
the
unlikely event
strange smell from
switch it off
to the
,
unplug
Use an air spray or soft cloth that
is moist with a neutral detergent
or
projector,
it from the
and water for
wall outlet and contact your
dealer or service centre.
electric shock hazard.
This may cause
shock hazard or
a
fire
or an
damage
stains
on
the
removing
projection
dust
or
lens.
electric
to the unit!
NOTES
Contact the Service
When
Center
year to
clean the internal
wipe
parts of the projector.
shiner, abrasive
once a
Accumulated dust
cause
cloth.
cleaning
it with
Use
and water for
mechanical failure.
It
the
can cause
an
never use
or
such
plastic parts
soft cloth. Do not
Especially,
product.
can
a
wax,
use
as
projector
case,
cleanser, spray
cleanser
unplug the power and
or wipe with a wet
water
(glass cleaner),
benzene, alcohol etc., which
automobile
or
industrial
damage the
neutral detergent
can
air spray or soft cloth that is moist with a
dust or stains on the projection lens.
removing
fire, electric shock
or
product damage (deformation,
corrosion and
damage).
WARNING
Do not
attempt
This may
cause
to service the
damage
to the
projector yourself.
projector
and could
Contact your dealer
give
an
electric Shock
as
or
well
service centre.
as
invalidating
the warranty !
NOTES
Be
sure
to
unplug
if the
is not to be used for
a
projector
long peri-
Refer
od.
Accumulated dust may cause
hazard or damage to the unit!
Only
use
This could
6
the
a
fire
specified type
of
cause
damage
lamp servicing
personnel.
service
to
qualified
Do not mix
new
batteries with old
batteries.
This may cause the batteries to
heat and leak.
battery.
to the remote control.
over-
Names of
parts
ENGLISH
Names of parts
Main
*
Body
The
on
screen
projector is manufactured using high-precision technology. You may, however, see
tiny black points and/or bright points (red, blue, or green). This can be a normal
manufacturing process and does not always indicate a malfunction.
result of the
Rear remote control
Control
Zoom
panel
the
Projector
sensor
ring
Focus
Power button
ring
Indicators
P
O
W
RE
A
U
OT
EYK
S
OT
EN
KO
UN
M
E
KE
SY
OT
EN
OS
RU
E C
Foot
adjusting
Front remote control
Lens
*
Foot
adjusting
Only
cover
into the inside after
you mount on the ceiling, after
is installed. If not, the cover may
(If
pulling it open into the
pushing the cover, the lens
overlap projecting lens.)
Part
HDMI
SVC
Push the lens
cover
Connecting
sensor
cover
front.
button
button
S-Video
RGB Input
(PC/DTV)
Component(Pr, Pb, Y)
Video
AC IN
Kensington Security
System Connector
(Refer to page 14)
7
Names of
parts
Control Panel
/
,
KEYSTONE+/- Button
MENU
Selects
or
closes
SOURCE
KEYSTONE
MENU Button
SOURCE Button
Switches to RGB, HDMI, Video, S-Video,
menus.
/
Adjusts
AUTO Button
A
KEYSTONE
AUTO
OK
POWER Button
POWER
8
Button
functions of
menus.
OK Button
Checks present mode and
saves the change of functions.
Compoment
mode.
Names of
parts
ENGLISH
Remote Control
POWER
POWER Button
MENU
KEYSTONE
SOURCE
MENU Button
F
AUTO Button
SOURCE Button
KEYSTONE+/-,
/ GButton
(Refer
to
p.26)
A
AUTO
BLANK Button
(Refer
to
KEYSTONE
/ EButton
OK Button
OK
ARC Button
p.24)
BLANK
D
(Refer
to
p.22)
ARC
STILL Button
(Refer
to
p.25)
STILL
Installing
Batteries
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED WITH AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
?
Open
the
battery compartment
cover on
the back of the
remote control.
?
Insert the
specified type
match "+" with
?
of batteries with correct
"+", and match
Don't mix used batteries with
"-"
polarity,
with "-".
new
batteries.
9
Names of
parts
Projector Status
*
Lamp indicator, operation
projector.
Indicators
indicator and temperature indicator at the top of the
projector
show the
user
the
operating
status
of the
Lamp
Operation
OP
W
E
R
Indicator
Indicator
Temperature
Indicator
A
U
OT
V
O
L
M
E
UN
O
K
OV
L
OS
RU
EC
Orange
Green(flashing)
Operation
Indicator
Standby.
Lamp is starting up.
Green
Unit is in operation (Lamp is turned on)
Orange(flashing) Projector lamp is cooling (1 min. 30 sec.)
Off
Power off.
Red
Lamp
Projector lamp is reaching the end of its life and needs
replaced with a new lamp. (over 2000 hours)
The projector is experiencing an error. Retry Power On
again later. If lamp indicator is red (flashing) again, con-
to be
Indicator
Red(flashing)
tact the service center.
Green(flashing)
The
lamp cover is open.
high temperature state has been detected. Turn the
Projector off.
The Projector has turned off due to excessive heat.
Power has turned off due to problem with the internal
cooling fan. Contact your service center.
A
Orange
Temperature
Indicator
Red
Red
10
(flashing)
Names of
parts
ENGLISH
Accessories
POWER
MENU
AUTO
KEYSTONE
SOURCE
OK
KEYSTONE
BLANK
ARC
STILL
1.5V
1 5V
.
Remote Control
2 Batteries
Power Cord
Computer
Optional
*
Contact your dealer to
*
When
*
Contact your
Video Cable
Cable
Extras
purchase these items.
ceiling installer, use only the ceiling
service personnel for replacing of lamp.
applying
Owner's Manual
a
installer for
projector.
Ceiling
Projection
Screen
S-Video Cable
Portable
Lamp
SCART to RCA jack
HDMI Cable
Component
installer for
projector
(option)
Cable
Bag
11
Installing
and
Composition
Installing and Composition
Installation Instructions
*
Don't
the
place
projector
in the
following
conditions. It may
Provide proper ventilation for this
cause
malfunction
or
product damage.
projector.
The projector is equipped with ventilation holes(intake)
on the bottom and ventilation holes(exhaust) on the front.
Do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation
or damage to the projector.
Do not place the projector on a carpet, rug or other
similar surface. It may prevent a adequate ventilation
of the projector bottom. This product should be
mounted to a wall or ceiling only.
Never
Leave
push projector
projector.
Place this
Install this
Don't
This may
or
any kind of
spill
in
in
a
adequate temperature
location where
place the projector
cause
into the
more)
projector
projector only
liquid
overheating
where it
of the
and
adequate distance(30cm/12
projector.
inches
humidity conditions.
adequate temperature
can
an
around the
and
humidity
is available.
(refer p.31)
be covered with dust.
projector.
Do not obstruct the slots and
openings
of the
projector.
This may
cause
overheating
and create
a
fire
hazard.
The
projector is manufactured using high-precision technology. You may, however, see tiny black points
bright points (red, blue, or green) that continuously appear on the projector Screen. This is a norresult of the manufacturing process and does not indicate a malfunction.
and/or
mal
To
display
projector.
If there is
12
DTV programs, it is necessary to
no
input signal, the
purchase
Menu will not be
a
DTV receiver
displayed
on screen.
(Set-top Box)
and connect it to the
or
Installing
Basic
1.Place the
ENGLISH
sturdy
and horizontal surface with the PC
on a
projector
with the desired distance from the
determines the actual size of the
screen
Composition
Projector
projector
2.Place the
the
of the
Operation
and
screen.
or
AV
source.
The distance between the
projector
and
image.
3. Position the
projector so that the lens is set at a right angle to the screen. If the projector is not set at a right
screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to
angle, the
page 24.).
4.Connect the cables of the
projector
to
a
wall power socket and other connected
projection distance
based
Projection
on
the
sources.
picture format
off-set ratio:127%
Image height (X)
Center line of lens
Image
width
Projection
distance
(D)
Projection
distance
(D)
(Y)
15:9
Image
format
mm/ inches
40′′
60′′
80′′
100′′
120′′
140′′
160′′
180′′
200′′
Image
height (X)
523/21
784/31
1045/41
1307/51
1568/62
1830/72
2091/82
2352/93
2614/103
Image
(Y)
871/34
1307/51
1742/69
2178/86
2614/103
3049/120
3485/137
3920/154
4356/171
1376/54
2075/82
2773/109
3472/137
4171/164 4870/192 5569/219
6268/247
6967/274
1638/64
2470/97
3303/130
4135/163
4967/196 5800/228
7464/294
8297/327
size
width
The shortest
distance
The
The
(D)
longest
(D)
distance
*
picture
longest/shortest
distance show status when
adjusted by
the
zoom
6632/261
function.
13
Installing
and
Composition
Using Kensington Security System
The
projector has a 'Kensington' Security System
Security System cable as below.
For the detailed installation and
to the
And
use
Kensington Security System
for
further
Kensington
information,
of the
Connector
Kensington Security System,
contact
http://www.kensington.com,
expensive electronic equipment
tors.
is
an
optional
item.
K
14
the back
panel.
Connect the
refer to the user's
'Kensington'
guide
attached
set.
company that deals with
Kensington Security System
on
the
such
internet
as
homepage
notebook PCs
or
of
the
projec-
Installing
Turning
the
on
1. Connect power cord
2. Remove the lens
An
ENGLISH
correctly.
cover
of the
on
projector.
the remote control
indicator flashes if
lamp
is in
top cover.
start-up cycle.)
or
will appear after the operation indicator light turns
Select the source mode with the SOURCE button.
image
Leave the
cooling
*
Don't
projector plugged
help
to preserve the
the power cord while the ventilation fan
Turning
off the
(Green).
in for at least 1 minute 30 seconds after
to continue which will
unplug
lamp
switching
(inlet/outlet)
is
working.
projector,
as
this will allow the
If so, this may increase risk of
lamp
damage
to the
lamp.
Projector
on
the
top
cover or
remote control.
2. Press the POWER button
on
the
top
cover or
remote control
3. If the
operation indicator LED is orange and blinking,
operation indicator LED is lit constantly (orange).
operation
off the
life.
1. Press the POWER button
If the
Composition
Projector
3. Press the POWER button
(Green operation
and
indicator LED is orange and
blinking,
again
to turn off the power.
do not disconnect the
the power button
on
the top
cover or on
supply
until the
the remote control will not
operate.
Power Off?
Please press Power
key again.
15
Installing
and
Composition
Focus and Position of the Screen
When
an
image appears
on
Image
the screen, check if it is in focus and fits well to the
Zoom
screen.
ring
Focus
ring
P
OW
E
R
A
UT
O
V
OL
K
O
ME
NU
L
VO
SO
UR
CE
To
To
adjust the
adjust the
focus of the
size of the
image, rotate the focus ring which is the outer ring on the lens.
image, rotate the zoom ring which is the inner ring on the lens.
To raise
or lower the image on the screen, extend
by pushing foot adjusting button as below.
1. While
the foot
pressing
adjusting button,
2. Release the button to lock the foot in its
3. To fine-tune the
After
raising
height
of the
projector,
raise
new
lower the
retract the foot at the bottom of the
projector to place
on
the
or
lower it.
projector.
mode
source
1. Press the SOURCE button.
select
F
OK
RGB
2. Each press of the F,
G
G
button
changes
RGB
Component
16
the
display
as
HDMI
S-Video
the
position.
rotate the front foot to raise
the front foot, do not press down
Selecting
or
or
Video
below.
screen
image
in the proper
position.
projector
Connection
ENGLISH
Connection
Connecting
*
You
can
*
You
can use
*
connect the
projector to
How to connect
Connect
a
computer of VGA, SVGA, XGA and SXGA output.
signals of the Aspect Ratio 4:3. (For
input signal is not included in the Spec., so the set
supported monitor displays of the projector.
HD wide
Refer to page 28 for the
<
Desktop PC
ARC function for the RGB
Fundamentally,
*
to a
HD wide
input signals, you cannot use
signal perfectly.
ARC
function.)
may not support HD
>
computer cable
to RGB
of the
Input (PC/DTV)
projector.
Connecting
to a Notebook PC
How to connect
<
Connect
>
computer cable
to RGB
Input (PC/DTV)
of the
projector.
*
If you set your computer to output the signal to both the
display of your computer and the external projector, the
picture of the external projector may not appear properly.
In such cases, set the output mode of your computer to
output the signal only to the external projector. For
details, refer to the operating instructions supplied with
your computer.
Connecting
*
You
can
connect
a
to a Video Source
VTR,
a
camcorder
or
any other
compatible
video
image
source
to the
projector.
<Howtoconnect1>
a.
Connect the Video
jacks
of the A/V
input jacks
source
of the
projector to
the
output
with Video cable.
<Howtoconnect2>
<VCR>
S VIDEO
(R) AUDIO (L)
VIDEO
OUT
b. Connect the S-Video
input jack
of the
projector to
the
IN
S-Video
*
output jack of an A/V source with an S-Video cable.
get better picture quality when connecting
S-Video source to the projector.
You
can
17
Connection
to a DVD
Connecting
*
The output
<
a.
jacks (Y, PB, PR)
How to connect
Connect the DVD
of the
*
might
be labelled
as
Y, Pb, Pr / Y, B-Y, R-Y / Y, Cb, Cr according
Component
connecting
with the
a
cable to
Component Pr, Pb,
the
cable, match the
component
jack
component cable.(Y=green, PB=blue, PR=red)
DVD with
to the
equipment.
>
Y
projector.
When
b. Use
of the DVD
Component
cable
colors
Component 480i(576i)/480p(576p), 720p,
1080i mode.
(R) AUDIO (L)
Y
PB
PR
<DVD>
Connecting
*
*
to a D-TV
Set-Top
Box
To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and
connect it to the projector.
Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and
D-TV Set-Top Box.
<
How to connect
a.
Connect RGB cable to RGB
an
RGB
source >
Input (PC/DTV)
of the
<D-TV
projector.
b. Use
*
a
DTV receiver with DTV
480p(576p)/720p/1080i
mode.
(R)AUDIO (L)
DTV OUTPUT
Box>
DVI OUTPUT
Y
PB
PR
HDMI supports HDCP.
<
How to connect
a.
Connect the D-TV
a
Component
*
b. Use
a
DTV receiver with DTV
Component
source >
Set-Top Box Component cable to
Component Pr, Pb, Y of the projector.
When connecting the component cable, match the jack
with the component cable.(Y=green, PB=blue, PR=red)
18
Set-Top
480p(576p)/720p/1080i
cable
colors
(R)AUDIO(L)
mode.
DTVOUTPUT
DVI OUTPUT
Y
PB
PR
Function
ENGLISH
Function
*
*
*
In this
manual, the OSD(On Screen Display) may be different from your Projector's
help with the Projector operation.
If there is no input signal present, the Menu will not be displayed.
This operating guide explains operation of RGB(PC) mode mainly.
Video Menu
because it is
just
an
example
to
Options
<RGBmode>
Adjusting
Video
1. Press the MENU button and then
use
D, E button to select the
menu.
Contrast
50 G
Brightness
50
Reset
2. Press the G button and then
want to
use D
,
button to select
E
a
video item you
adjust.
3. Press the F, G button to
adjust
4. Press the A OK button to
save
the
screen
the
new
condition
as
you want.
Menu
settings.
menu options will not affect other inputs.
adjustment of
As required, re-adjust
menu options for the following input source :
Video/S-Video/Component (480i(576i)), Component (480p(576p), 720p, 1080i)
To restore the original image condition after changing it, press A OK button
after selecting [Reset] item.
When receiving an NTSC signal, the picture item Tint is displayed and can
be adjusted.(60Hz only)
To exit the menu display, repeatedly, press the MENU button.
<
Each
APC
*
(Auto
Picture
Use APC to set the
Video mode
APC
G
>
Clear
Contrast
80
Soft
Brightness
Sharpness
50
User
Menu
*
Prev.
50
Prev.
Control)
projector
for the best
picture
appearance.
This function will not work in RGB mode.
1. Press the MENU button and then
use
D, E button to select the
E
button to select APC item.
menu.
APC
2. Press the G button and then
3. Press the G button and then
condition
as
use D
,
,
E
button to
adjust
the
G
Clear
Contrast
80
Soft
Brightness
50
User
Sharpness
50
screen
you want.
4. Press the A OK button to
Each press of the D,
Clear
To exit the
use D
E
save
button
the
new
changes
Soft
menu
display, repeatedly,
the
settings.
screen as
Menu
Prev.
shown below.
User
press the MENU button.
19
Function
Auto Color
-
Temperature Control
To initialize values
(reset
to default
settings),
1. Press the MENU button and then
2. Press the G button and then
select the Normal
option.
use
D, E button to select the
E
button to select ACC item.
use D
,
menu.
ACC
G
Cool
10
Warm
Gamma
3. Press the G button and then
use D
,
button to make desired
E
adjustments.
White
peaking
Color
temp.
Normal
Color enhancement
4. Press the A OK button to
Each press of the D,
E
the
save
button
new
changes
settings.
the
Reset
screen as
shown below.
Menu
Cool
To exit the
Normal
menu
Prev.
Warm
display, repeatedly,
press the MENU button.
Gamma Function
1. Press the MENU button and then
2. Press the G button and then
3. Press the G button and then
use
use D
use D
,
,
E
E
D, E button to select the
Each press of the D,
Normal
To exit the
20
E
save
button
the
button to
new
changes
Film
menu
display, repeatedly,
ACC
button to select Gamma item.
adjust the
screen
required.
4. Press the A OK button to
menu.
settings.
the
screen as
condition
as
Gamma
G
White
peaking
10
Color
temp.
Color enhancement
Reset
Menu
shown below.
Sports
press the MENU button.
Prev.
Normal
Film
Sports
Function
White
peaking
Function
1. Press the MENU button and then
2. Press the G button and then
D, E button to select the
use
use D
button to select White
E
,
ENGLISH
menu.
peaking
item.
ACC
Gamma
3. Press the F, G button to
adjust
the
screen
the
new
condition
as
White
you want.
peaking
Color
5 G
temp.
Color enhancement
4. Press the A OK button to
White
settings.
Reset
RGB(PC) and HDMI(DVI) Mode.
The default value may changed based on input mode.
Adjust to higher setting to achieve brighter picture. Adjust to lower setting
darker picture.
To exit the menu display, repeatedly, press the MENU button.
Peaking
is
save
only
available in
Menu
Prev.
for
Color temperature Control
*
You
can
adjust
color to any color temperature you
1. Press the MENU button and then
2. Press the G button and then
D, E button to select the
use
use D
button to select Color
E
,
prefer.
temp.
menu.
item.
ACC
Gain R
50
Gamma
Gain G
50
10
Gain B
50
G
Offset R
0
Offset G
0
Offset B
0
White
3. Press the G button and then
or
use D
button to select Gain R, Gain G, Gain B
E
,
Reset
appropriate adjustments.
The Gain R, Gain
G, Gain B adjustment range is 0
The Offset R, Offset G,Offset B adjustment range is
5. Press the A OK button to
To exit the
menu
temp.
Color enhancement
Offset R, Offset G, Offset B.
4. Use the F, G button to make
Color
peaking
save
the
new
display, repeatedly,
~
Menu
100.
-50
Prev.
+50.
~
settings.
press the MENU button.
Color enhancement Control
*
You
can
adjust
color to any color enhancement you
1. Press the MENU button and then
2. Press the G button and then
3. Press the G button and then
Blue, Yellow, Cyan,
4. Use the F, G button to
The
adjustment
Magenta
or
Reset
(Reset
To restore the
D, E button to select the
use
,
use D
E
,
E
menu.
button to select Color enhancement item.
button to select Color, Red, Green,
adjust
the
ACC
Color
50
Gamma
Red
50
Green
50
Blue
50
Yellow
50
Cyan
50
Magenta
50
White
peaking
Color
temp.
10
Color enhancement G
Magenta.
Reset
condition
screen
as
desired.
range of Color, Red, Green, Blue, Yellow,
Cyan,
and
Menu
Prev.
is 0~100.
5. Press the A OK button to
To exit the
use D
prefer.
menu
to
save
the
new
display, repeatedly,
settings.
press the MENU button.
original factory value)
original image
condition after
changing it,
press the AOK button after
selecting [Reset]
item.
21
Function
Menu
Special
Options
Selecting Language
1. Press the MENU button and then
use
D, E button to select the
menu.
Language
2. Press the G button and then
3. Press the G button and then
to
use D
use D
,
,
button to select
E
E
Language
button to select the
language
you want
Flip
horizontal
Flip
vertical
Auto
save
the
new
Deutsch
Francais
Italiano
Espanol
Portugues
settings.
Menu
On-Screen-Display (OSD) is displayed in the selected language.
To exit the menu display, repeatedly, press the MENU button.
Using ARC
Function
1. Press the ARC button.
Each press of the button
changes
the
Full
display
as
below.
16:9
Full
16:9
Zoom2
also
use
4:3
4:3
Zoom1
Zoom2
can
English
Svenska
4. Press the A OK button to
22
sleep
use.
You
G
ARC
item.
this function
Zoom1
by using
the MENU button.
Prev.
Function
*
ENGLISH
horizontal Function
Flip
This function
reverses
the
Use this function when
projected image horizontally.
projecting an image.
rear
1. Press the MENU button and then
D, E button to select the
use
menu.
Language
2. Press the G button and then
3. Press the G button to
see
Each time you press the
To exit the
Flip
menu
use D
reversed
G
button to select
E
,
Flip horizontal
item.
image.
ARC
Flip
horizontal
Flip
vertical
Auto
sleep
Menu
Prev.
G
To
flip
G
To
flip
button, the image will be reversed.
press the MENU button.
display, repeatedly,
Vertical Function
*
This function
*
When you hang the projector upside down from the ceiling
you will need to reverse the image vertically and horizontally.
reverses
the
projected image vertically.
,
1. Press the MENU button and then
D, E button to select the
use
menu.
Language
2. Press the G button and then
3. Press the G button to
see
Each time you press the
To exit the
menu
Auto
*
The
sleep
use D
reversed
G
Flip Vertical
item.
image.
ARC
Flip
horizontal
Flip
vertical
Auto
sleep
Menu
Prev.
button, the image will be reversed.
press the MENU button.
display, repeatedly,
sleep
button to select
E
,
Function
timer turns the
projector
off at the
1. Press the MENU button and then
use
preset time.
D, E button to select the
menu.
Off
Language
2. Press the G button and then
3. Press the G button and then
use D
use D
E
,
,
E
button to select Auto
sleep
button to select the desired
item.
preset time.
10 Min
ARC
Flip
horizontal
Flip
vertical
Auto
sleep
20 Min
30 Min
60 Min
G
90 Min
120 Min
4. Press the A OK button to
To exit the
menu
save
the
new
display, repeatedly,
180 Min
settings.
press the MENU button.
240 Min
Menu
Prev.
23
Function
Menu
Special
Using Keystone
*
*
Function
Use this function when the
Only
use
the
Keystone
2. Press the KEYSTONE
rect the
is not at
right angle
a
or
+
+
or
KEYSTONE
KEYSTONE
get
to the
the best
projector and the image
angle of projection.
is
a
trapezoid shape.
button.
-
button to
-
adjust as
needed to
cor-
keystone.
Keystone
You
screen
function when you can't
1. Press the KEYSTONE
can
can
also
be
adjusted
access
Using
*
Options
Keystone
from -20 to +20.
0
FG
this function via the MENU button.
Blank Function
This function may be effective if you need to
get
the attention of the audience
during presentations, meetings
or
briefings.
1. Press the BLANK button.
The
screen
You
can
(Refer
turns off to
background color.
background color.
'Selecting blank image color')
a
choose the
to
2. Press any button to cancel the blank function.
Selecting
Blank
image
color
1. Press the MENU button and then
use
D, E button to select the
menu.
Keystone
2. Press the G button and then
3. Press the G button and then
use D
use D
,
,
E
E
button to select Blank
image
item.
button to select the color you want to
use.
0
Blank
image
Lamp
mode
Black
Lamp
time
Green
G
Blue
Logo
4. Press the A OK button to
Background
To exit the
24
save
the
new
settings.
color will be altered to the selected Blank function color.
menu
Menu
display, repeatedly,
press the MENU button.
Prev.
Function
ENGLISH
mode Function
Lamp
1. Press the MENU button and then
use
D, E button to select the
menu.
Keystone
2. Press the G button and then
3. Press the G button and then
use D
,
use D
,
button to select
E
Lamp
mode item.
button to select Normal mode
E
Blank
0
image
Lamp
mode
Lamp
time
Menu
Prev.
G
Normal mode
Silent mode
or
Silent mode.
4. Press the A OK button to
To exit the
menu
the
save
new
display, repeatedly,
Checking Lamp
settings.
press the MENU button.
time
1. Press the MENU button and then
use
D, E button to select the
menu.
Keystone
2. Press the G button and then
use D
E
button to select
Lamp time
item.
The used
When
lamp time is displayed.
projector lamp is reaching
,
the end of its life
(approximately
2000
hours),
the
Blank
image
Lamp
Lamp
time
0
mode
10
Hr
lamp
indicator will turn red.
The
LED illuminates red
lamp warning
continuously
in the
case
of excessive
lamp
time.
Menu
To exit the
display, repeatedly,
menu
Using Still
Prev.
press the MENU button.
Function
1. Press the STILL button.
*
You
can
freeze the
input image.
<Still
<Moving Image>
2. To exit
*
STILL, press any button
The STILL function will release
Image>
.
automatically
after
approximately
10 minutes.
25
Function
Screen Menu
Auto
*
Function
Configure
This function
Options
assures
you of
getting
the best video
quality by automatically adjusting
the horizontal size and
synchronization
of the
*
Auto
image.
Tracking
function works in RGB PC
input only.
1. Press the AUTO button.
Image positioning
2.
Adjust
Manual
and
synchronization
in
configure
are
automatically adjusted.
menu
after
operating
Auto
configure
Auto
Configure
if you want to get better picture quality in accordance with diverse PC
input modes. In certain circumstances, you can't get the best picture
quality by only using auto-correction.
You
can
For best
also
this function
use
Manual
*
Manual
*
Phase Function
the MENU button.
a
in RGB
(Only
still
mode)
image.
configure
Configure
is available in RGB PC mode
This function is for the detailed
*
by using
results, perform this function while displaying
only.
of the
adjustment
phase
function.
Clock Function
This function
adjusts
the horizontal width of the
1. Press the MENU button and then
projected image
to
get
the
D, E button to select the
use
image
to fit to the
screen
menu.
Auto
2. Press the G button and then
use D
button to select Manual
E
,
configure
item.
3. Press the G button and then
H Position
or
use D
,
E
button to
adjust
the
adjustment range is 0 63.
adjustment range is -50 +50.
the input mode, the adjustment range
~
The Clock
on
~
5. Press the A OK button to
To exit the
26
condition.
menu
save
the
new
display, repeatedly,
may be
changed.
settings.
press the MENU button.
Phase
32
Clock
0
Position
H Position
0
Reset
V Position
0
button to select Phase, Clock,
screen
G
Zoom +/-
V Position.
The Phase
Based
configure
configure
Manual
Menu
4. Press the F, G
size.
Prev.
Function
Using ZOOM
ENGLISH
Function
1. Press the MENU button and then
D, E button to select the
use
menu.
Auto
2. Press the G button and then
use D
E
,
button to select Zoom
+/-
item.
configure
Manual
configure
Zoom +/-
G
100%
FG
Position
3. Press the G button and then
Zoom
+/- adjustment
To exit the
menu
button to
F, G
use
range is 100%
zoom
in
or
out of the
picture.
Reset
250%.
~
press the MENU button.
display, repeatedly,
Menu
Prev.
Screen Position
*
This function is
only
available
once
the
1. Press the MENU button and then
picture
use
has been zoomed.
D, E button to select the
menu.
Auto
2. Press the G button and then
use D
,
E
button to select Position item.
configure
Manual
configure
Zoom +/Position
3. Press the G button and then
use
D, E, F, G button to
4. Press the A OK button to
the
new
To exit the
Reset
(Reset
menu
To restore the
to
save
display, repeatedly,
adjust
the
position.
D
G
FG
E
Reset
settings.
press the MENU button.
Menu
Prev.
original factory value)
original image
condition after
This function resets all Manual
changing it, press AOK button after selecting [Reset]
Configuration settings. (Zoom +/-, Position etc).
item.
27
Information
Supported
*
The
table lists the
following
Display
the
projector.
Format
70.090Hz
31.468kHz
640X350
85.080Hz
37.861kHz
640X400
70.090Hz
31.468kHz
640X400
85.080Hz
37.861kHz
720X400
70.082Hz
31.469kHz
720X400
85.039Hz
37.927kHz
640X480
59.940Hz
31.469kHz
640X480
72.800Hz
37.861kHz
640X480
75.00Hz
37.500kHz
640X480
85.008Hz
43.269kHz
800X600
56.250Hz
35.156kHz
800X600
60.317Hz
37.879kHz
800X600
72.188Hz
48.077kHz
800X600
75.00Hz
46.875kHz
800X600
85.061Hz
53.674kHz
1024X768
60.004Hz
48.363kHz
1024X768
70.069Hz
56.476kHz
1024X768
75.029Hz
60.023kHz
1024X768
84.997Hz
68.677kHz
1152X864
60.053Hz
54.348kHz
1152X864
70.01Hz
63.995kHz
1152X864
75.00Hz
67.500kHz
1280X768
60.00Hz
47.693kHz
1280X960
60.00Hz
60.00kHz
1280X1024
60.020Hz
63.981kHz
XGA
SXGA
*
supported by
640X350
SVGA
*
formats
VGAEGA
VGA
*
display
Sources
PC98 / VGA text
*
Monitor
Vertical
Freq.(Hz)
Horizontal
Freq. (kHz)
If the
projector does not support the input signal, "Out of Range" message appears on the screen.
The projector supports DDC1/2B type as Plug & Play function. (Auto recognition of PC monitor)
The Synchronization input form for horizontal and vertical frequencies are Separate, Composite and SOG.
According to PC, the optimum vertical frequency may not be displayed up to the optimum frequency of set in
'Registration information (Display registration information)'. (ex, The optimum vertical frequency may be displayed
up to 85Hz
under in the resolution of 640X480
or
<DVD/DTV
or
800X600.)
Input>
Component-*1
RGB(DTV)-*2
480i
O
X
X
480p
O
O
O
Signal
NTSC(60Hz)
HDMI(DTV)-*3
720p
O
O
O
1080i
O
O
O
576i
O
X
X
576p
O
O
O
720p
O
O
O
1080i
O
O
O
*
PAL(50Hz)
Cable type
12-
Component Cable
Computer Cable
3- HDMI Cable
*
If you want to see a cleaner picture in the RGB/HDMI
720p signal, select the ZOOM 1 mode in ARC function.
Maintenance
*
The
on
projector
the
always
needs little maintenance. You should
keep the
lens clean because any dirt
If any parts need to be replaced, contact your dealer. When
turn the power off and unplug the projector first.
screen.
cleaning
or stains may appear
any part of the projector,
the lens
Cleaning
Clean the lens whenever you notice dirt
lint-free cloth.
or
dust
on
the surface of it.
Wipe the
lens surface
gently with
an
air spray
or a
soft,
dry
To
remove
dirt
or
Cleaning
stains
the
projector
stubborn dirt
or
28
use
the lens, moisten
Projector
To clean the
Do not
on
a
soft cloth with water and
a
neutral
detergent
and
wipe
the lens surface
gently.
Case
case, first unplug the power cable. To remove dirt or dust, wipe the casing with a soft, dry, lint-free cloth. To
stains, moisten a soft cloth with water and a neutral detergent and then wipe the casing.
alcohol, benzene, thinners or other chemical detergents as these can cause the casing to be warped or discolored.
remove
Information
ENGLISH
Replacing the Lamp
Lamp Replacement
The
is rated for
projector lamp
approximately 2000 hours. You can see the used lamp
(p.25). You must replace the lamp when:
<Front
panel
of the
Projector>
time in the LAMP TIME section of the Menu
The
projected image gets darker or starts to deteriorate.
lamp indicator is red.
The message "Replace the lamp" appears on the screen
projector on.
Lamp
The
Be careful when
-
-
turning
indicators
the
replacing lamp
Press the POWER button
If the
when
on
the control
panel
or
remote control to turn off power.
indicator LED is orange and
operation
blinking, do not disconnect the main supply until the operation indicator LED
constantly (orange).
Allow the lamp to cool for 1 hour before replacing it.
Replace only with the same type lamp from an LG Electronics Service Center. Using another manufacturers lamp may
cause damage to the Projector and lamp.
Pull out the lamp only when replacing the lamp.
Keep the lamp unit out of reach of children. Keep the Lamp away from heat sources such as radiators, stoves etc.
To reduce the risk of fire do not expose the lamp to liquids or foreign materials.
Do not place the lamp near any heat source.
Make sure the new lamp is securely tightened with screws. If not, the image may be dark or there could be an increased
is lit up
-
-
-
-
-
-
-
risk of fire.
-
Never touch the
To obtain
Lamp
Using
a
lamp
unit
glass
otherwise
replacement Lamp
model number is
image quality
Dispose
unit
compromised
or
lamp
life
maybe
reduced.
unit
on page 31. Check the
another manufacturers lamp may cause
Lamp
may be
lamp model and then purchase
damage to the projector.
it from
an
LG Electronics Service Center.
disposal
of the used
lamp by returning
it to the LG Electronic Service Center.
29
Information
the
Replacing
1
Turn off the
Lamp
Carefully place
(Allow
the
removing
and
projector
lamp
on a
unplug
the power cable.
cushioned surface.
2
Unscrew the
3
lifting
retaining
the
from the
lamp
cover
using
a
to cool for 1 hour before
the used
lamp
from the
projector.)
Lamp
After
screws
screwdriver.
lamp
screws on
cover
the
off,
lamp
remove
case
with
case
bolt
the two
a screw-
driver.
4
Lift the
lamp
up
by
the attached knob.
Knob
Bolt
5
Pull out the handle
slowly
and
remove
the
case.
7 Tighten
(Make
the
sure
screws
they
are
you removed in
fixed
firmly.)
step
3.
lamp
6
8
Insert the
Make
Close the
step
Using
another manufacturers
sure
(If the lamp
If this fault
30
lamp may cause damage to the projector
lamp cover is securely fastened. If the lamp cover is not
persists contact an LG Authorized Service Center.
the
or
lamp gently
it is inserted
lamp
cover
2 to install the
power
Make
new
sure
cover
into the correct
position.
correctly.
and install the
screws
from
cover.
is not installed
correctly the
unit will not
on.)
lamp.
installed
correctly
the unit will not power
on.
Information
Specifications
MODEL
BN315-JD
resolution
1280(Horizontal)
horizontal / vertical ratio
DLP
panel
size
0.65 inches
Wide
Tele
:
:
1.35
1.60
7.00m(40
~
~
remote control distance
8.30m(40
inches)
compatibility
NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N
AC 100
-
240V~50/60Hz,3A-1A
100.7/3.9
breadth(mm/inches)
330/12.9
length(mm/inches)
220.1/8.7
Operating
Condition
temperature
In operation : 32~104°F(0°C~40°C)
storage and transit : -4~140°F(-20°C~60°C)
humidity
operation : 0~75% relative humidity by dry hygrometer
operation : 0 85% relative humidity by dry hygrometer
Not in
inches)
1:1.2
height(mm/inches)
In
200
~
12m
Power
In
200
~
ratio
zoom
Video
768(Vertical)pixel
15:9(horizontal:vertical)
size
screen
x
Projector Lamp
lamp
model
AJ-LBN3
lamp power consumption
200W
~
31
P/NO
:
38289U0029F
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement