advertisement
▼
Scroll to page 2
of 38
OWNER’S MANUAL DVD Home Theater System Please read this manual carefully before operating your set and retain it for future reference. HT406TQ (HT406TQ, SH36TQ-S, SH36PD-C, SH36SU-W) HT306TQ-F2_DCHNLL_ENG_5796.indd 1 2012-12-11 �� 4:38:51 2 Getting Started Safety Information 1 CAUTION Getting Started RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. HT306TQ-F2_DCHNLL_ENG_5796.indd 2 2012-12-11 �� 4:38:52 Getting Started 3 This device is equipped with a portable battery or accumulator. Safe way to remove the battery or the battery from the equipment: 1 Getting Started Remove the old battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimburse ment system batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus. You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players. (Mastered/ Live File System : Disc format system for Windows Vista) HT306TQ-F2_DCHNLL_ENG_5796.indd 3 2012-12-11 �� 4:38:52 4 Table of Contents Table of Contents 1 Getting Started 2 6 6 6 6 7 7 7 7 7 8 10 11 12 Safety Information Unique Features – USB Direct Recording – Full HD up-scaling Accessories Introduction – Playable Discs – About the & Symbol Display – Symbol Used in this Manual – Regional Codes – Playable file Requirement Front panel Rear panel Remote control 2 Connecting 13 13 13 14 14 15 16 16 16 17 17 17 Connecting the speakers – Attaching the speakers to the unit – Positioning the System Connections to Your TV – HDMI OUT Connection – Component Video Connection – Video Connection Optional Equipment Connection – AUX IN Connection – PORT.(Portable) IN Connection – USB Connection – Antenna Connection 4 Operating 23 24 24 24 24 24 24 25 25 25 25 26 26 26 26 26 27 27 27 27 27 27 27 28 28 28 29 29 30 30 30 Basic Operations Other Operations – Displaying Disc Information on-screen – To display the DVD Menu – To display the DVD Title – Selecting a subtitle language – 1.5 times speed playback – Starting play from selected time – Last Scene Memory – Changing the character set to display DivX® subtitle correctly – Programmed Playback – Viewing a PHOTO file – Viewing photo files as a slide show – Listening to music during slide show – Sleep Timer Setting – Dimmer – Turn off the sound temporarily – Screen Saver – System Select - Optional – VOCAL FADER – Displaying file information (ID3 TAG ) Radio Operations – Listening to the Radio – Presetting the Radio Stations – Deleting all the saved stations – Improving poor FM reception Sound adjustment – Setting the surround mode Advanced Operations – Listening to music from your portable player or external device. – Recording to USB 3 System Setting 18 18 Adjust the Setup settings – OSD Initial language settings Optional 18 – To display and exit the Setup Menu 19 – LANGUAGE 19 – DISPLAY 20 – AUDIO 21 – LOCK (Parental Control) 22 – OTHERS HT306TQ-F2_DCHNLL_ENG_5796.indd 4 2012-12-11 �� 4:38:52 Table of Contents 5 5 Troubleshooting 31 Troubleshooting 6 Appendix 32 32 32 33 34 35 36 Maintenance – Handling the Unit – Notes on Discs Area Code List Language Code List Trademarks and Licenses Specifications 1 2 3 4 5 6 HT306TQ-F2_DCHNLL_ENG_5796.indd 5 2012-12-11 �� 4:38:52 6 Getting Started Unique Features 1 USB Direct Recording Accessories Please check and identify the supplied accessories. Getting Started Records music from CD to your USB device. Full HD up-scaling Views Full HD picture quality with simple setup. FM Antenna (1) Remote Control (1)/ Battery (1) Video Cable (1) Speaker cables (4) HDMI cable (1) HT306TQ-F2_DCHNLL_ENG_5796.indd 6 2012-12-11 �� 4:38:53 Getting Started Introduction Playable Discs DVD-VIDEO (8 cm / 12 cm disc) Discs such as movies that can be purchased or rented. DVD±R (8 cm / 12 cm disc) Video mode and finalized only. DVD-RW (8 cm / 12 cm disc) Video mode and finalized only. DVD VR format that have been finalized can not be played in this unit. DVD+R: Video mode only. Supports the double layer disc also. DVD+RW (8 cm / 12 cm disc) Video mode and finalized only. Audio CD: Music CDs or CD-R/CDRW in music CD format that can be purchased. Symbol Used in this Manual r DVD-Video, DVD±R/RW in Video mode or VR mode and finalized t Audio CDs y Video files contained in the USB/Disc u Audio files contained in the USB/Disc i Photo files 1 Getting Started This unit plays DVD±R/RW and CD-R/RW that contains audio titles, DivX, MP3, WMA and/or JPEG files. Some DVD±RW/DVD±R or CD-RW/ CD-R cannot be played on this unit due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. 7 ,,Note Indicates special notes and operating features. >>Caution Indicates cautions for preventing possible damages from abuse. Regional Codes This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or “ALL”. ost DVD discs have a globe with one or more yy M numbers in it clearly visible on the cover. This number must match your unit’s regional code; or the disc cannot play. yy If you try to play a DVD with a different regional code from your unit, the message “Check Regional Code” appears on the TV screen. About the & Symbol Display “&” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that disc. HT306TQ-F2_DCHNLL_ENG_5796.indd 7 2012-12-11 �� 4:38:53 8 Getting Started Playable file Requirement Compatible USB Devices yy MP3 Player : Flash type MP3 player. MP3/ WMA music file requirement 1 Getting Started MP3/ WMA file compatibility with this unit is limited as follows : yy S ampling frequency : within 32 kHz to 48 kHz (MP3), within 32 kHz to 48 kHz (WMA) it rate : within 32 kbps to 320 kbps (MP3), 40 yy B kbps to 192 kbps (WMA) yy Support Version : v2, v7, v8, v9 yy Maximum files : Under 999 yy File extensions : “.mp3”/ “.wma” yy CD-ROM file format : ISO9660/ JOLIET e recommend that you use Easy-CD Creator, yy W which creates an ISO9660 file system. Photo file requirement JPEG disc compatibility with this unit is limited as follows : yy Max pixel in width : 2 760 x 2 048 pixel yy Maximum files : Under 999 yy S ome discs may not operate due to a different recording format or the condition of disc. yy File extensions: “.jpg” yy USB Flash Drive : Devices that support USB2.0 or USB1.1. yy T he USB function of this unit does not support some USB devices. USB device requirement evices which require additional program yy D installation connected to a computer, are not supported. yy Do not extract the USB device while in operation. yy F or a large capacity USB, it may take longer than a few minute to be searched. yy To prevent data loss, back up all data. yy If you use a USB extension cable or USB hub, the USB device is not recognized. sing NTFS file system is not supported. (Only yy U FAT(16/32) file system is supported.) yy T his unit is not supported when the total number of files is 1 000 or more. yy E xternal HDD, Card readers, Locked devices, or hard type USB devices are not supported. SB port of the unit cannot be connected to PC. yy U The unit can not be used as a storage device. yy CD-ROM file format : ISO9660/ JOLIET HT306TQ-F2_DCHNLL_ENG_5796.indd 8 2012-12-11 �� 4:38:53 Getting Started 9 DivX file requirement DivX file compatibility with this unit is limited as follows : vailable resolution: yy A within 720 x 576 (W x H) pixels. yy If there is impossible code to express in the DivX file, it may be displayed as “ _ “ mark on the display. Getting Started yy T he file name of the DivX subtitle should be entered within 45 characters. 1 yy F rame rate : less than 30 fps. yy If the video and audio structure of recorded files is not interleaved, either video or audio is outputted. layable DivX file : “.avi”, “.mpg”, “.mpeg”, “.divx” yy P layable Subtitle format : SubRip (*.srt/ *.txt), yy P SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt), MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/ *.txt), Vobsub (*.sub) layable Codec format : “DIVX3.xx”, “DIVX4.xx”, yy P “DIVX5.xx”, “MP4V3”, “3IVX”. layable Audio format : “AC3”, “PCM”, “MP3”, “WMA”. yy P yy S ampling frequency : within 32 kHz to 48 kHz (MP3), within 32 kHz to 48 kHz (WMA) it rate : within 32 kbps to 320 kbps (MP3), 40 yy B kbps to 192 kbps (WMA) yy F or Discs formatted in Live file system, you can not it on this unit. yy If the name of movie file is different from that of the subtitle file, during playback of a DivX file, subtitle may not be display. yy If you play a DivX file different from the DivXspec, it may not operate normally. HT306TQ-F2_DCHNLL_ENG_5796.indd 9 2012-12-11 �� 4:38:53 10 Getting Started Front panel 1 1 2 4 5 6 9 8 Getting Started 3 12 11 10 7 a DVD/CD Disc Drawer h MIC 1/ 2 b Display window i USB port You can play video, image and sound files by connecting the USB device. c Open/Close (B) d Function (F) Selects the function or input source. e Play/Pause (d/M) f Stop (Z) g TUNING (-/+)(c/v), SKIP/SCAN (-/+) You can search chapter/ track/ file by pressing and holding c/v. HT306TQ-F2_DCHNLL_ENG_5796.indd 10 j PORT.(Portable) IN port You can enjoy music from portable device on your unit. k Volume (VOL.) l Power (1/!) 2012-12-11 �� 4:38:53 Getting Started 11 Rear panel 1 2 3 4 5 1 Getting Started 7 6 a Power cord e AUX (L/ R) INPUT connector b Speaker terminal f HDMI OUT connector c ANTENNA connector (FM) g COMPONENT VIDEO (PROGRESSIVE SCAN) OUTPUT (Y PB PR) Connect to a TV with Y PB PR inputs. d MONITOR (VIDEO OUT) connector Connect to a TV with video inputs HT306TQ-F2_DCHNLL_ENG_5796.indd 11 2012-12-11 �� 4:38:54 12 Getting Started Remote control 1 1 Getting Started 2 • • • • • • a • • • • • • • • • • • • d • • • • • • 功能 : Selects the function and input source. 随机/重复 : Selects a play mode. (Random, repeat) 睡眠 : Sets the system to turn off automatically at a specified time. (Dimmer : The display window will be darken by half.) 静音 : Mutes the sound. 电源 : Switches the unit ON or OFF. 3 4 开/关 : Opens and closes the disc Drawer. 片头 : If the current DVD title has a menu, the title menu appears on the screen. Otherwise, the disc menu may not appear. • • • • • • b • • • • • • 5 显示 : Accesses On-Screen Display. 菜单 : Accesses the menu on a DVD disc. 设置 : Accesses or removes setup menu. 预设 (WS) : Selects programme of Radio. Battery Installation 调台 (-/+) : Tunes in the desired radio station. W/S/A/D (up/ down/ left/ right): Used to navigate on-screen displays. 进入 (b) : Acknowledges menu selection. Remove the battery cover on the rear of the Remote Control, and insert one (size AAA) battery with 4 and 5 matched correctly. 返回 (x) : Moves backwards in the menu or exits the setup menu. 录音 (X) : USB Direct Recording. • • • • • • c • • • • • • 停止 (Z) : Stops playback or recording. 播放 (d), 单声/立体声 : Starts playback. Selects Mono/ Stereo. 音量 (Volume) (+/-) : Adjusts speaker volume. 特效 (9) : Selects a Natural or Local Specialization equalizer effect by using LG EQ. 音效$ (EQUALIZER effect) : Chooses sound impressions. 清除 : Removes a track number on the Program List. 字幕 : During playback, press 字 幕 repeatedly to select a desired subtitle language . 0 to 9 numerical buttons : Selects numbered options in a menu. • • • • • • e • • • • • • TV Control buttons : Controls the TV. (LG TV only) -- You can control the sound level, input source, and power switching of LG TVs as well. Hold POWER (TV) and press PR/CH (+/–) button repeatedly until the TV turns on or off. 编辑/记忆 : Accesses or removes Program menu. 解像度 : Sets the output resolution for HDMI and COMPONENT VIDEO OUT jacks. 麦克风音量(+/-) : Adjusts microphone volume. 回声音量(+/-) : Adjusts echo volume. 人声消除 : When you listen to music, it reduce the vocal of file. 暂停/步距 (M) : Pauses playback. 跳跃 (C/V) : Goes to next or previous chapter/ track/ file. 扫描 (c/v) : Searches backward or forward. HT306TQ-F2_DCHNLL_ENG_5796.indd 12 2012-12-11 �� 4:38:54 Connecting Connecting the speakers Attaching the speakers to the unit Connect the black stripe of each wire to the terminals marked - (minus) and the other end to the terminals marked + (plus). Speaker connection Positioning the System The following illustration shows an example of positioning the system. Note that the illustrations in these instructions differ from the actual unit for explanation purposes. For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening position ( ). Speaker Positioning Front left speaker (L)/ Front right speaker (R): Place the front speakers to the sides of the monitor or screen and as flush with the screen surface as possible. 2 Connecting To connect the cable to the unit, press each plastic finger pad to open the connection terminals on the unit. Insert the wire and release the finger pad. 13 Center speaker: Place the center speaker above or below the monitor or screen. Surround left speaker (L)/ Surround right speaker (R): Place these speakers behind your listening position, facing slightly inwards. >>Caution yy Be careful to make sure children not to put their hands or any objects into the *speaker duct. *Speaker duct: A hole for plentiful bass sound on speaker cabinet (enclosure). yy The speakers contain magnet parts, so color irregularity may occur on the TV screen or PC monitor screen. Please use the speakers far away from either TV screen or PC monitor. Subwoofer: The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reflections. Unit B C A G F A A A A D HT306TQ-F2_DCHNLL_ENG_5796.indd 13 E A 2012-12-11 �� 4:38:55 14 Connecting Connections to Your TV Make one of the following connections, depending on the capabilities of your existing equipment. HDMI OUT Connection If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable(Type A, High Speed HDMI™ Cable). Connect the HDMI OUT jack on the player to the HDMI IN jack on a HDMI compatible TV or monitor. ,,Note 2 Connecting yy Depending on your TV and other equipment you wish to connect, there are various ways you could connect the player. Use only one of the connections described in this manual. yy Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections. >>Caution yy Make sure the unit is connected directly to the TV. Tune the TV to the correct video input channel yy Do not connect your player via your VCR. The image could be distorted by the copy protection system. Set the TV’s source to HDMI (refer to TV’s Owner’s manual). HT306TQ-F2_DCHNLL_ENG_5796.indd 14 2012-12-11 �� 4:38:55 Connecting 15 Resolution Setting Component Video Connection You can change the resolution for component video and HDMI output. Connect the COMPONENT VIDEO (PROGRESSIVE SCAN) OUTPUT jacks on the unit to the corresponding input jacks on the TV using Y PB PR cables. Press 解像度 repeatedly to select the desired resolution - 480i (or 576i), 480p (or 576p), 720p, 1080i, 1080p The resolution may not be selected depending on the connection or TV. You can set 1080p video resolution to enjoy Full HD picture quality. (Full HD up-scaling) ,,Note 2 Connecting Depending on your TV, some of the resolution settings may result in the picture disappearing or an abnormal picture appearing. In this case, press 解像度 repeatedly until the picture re-appears. You can hear the sound through the system’s speakers. yy Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again. yy When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable. yy If there is noise or lines on the screen, please check the HDMI cable (High Speed HDMI™ Cable). yy When you use HDMI connection, you can change the resolution for the HDMI output. Press 解像度 repeatedly to select the desired resolution - 480i (or 576i), 480p (or 576p), 720p, 1080i, 1080p. HT306TQ-F2_DCHNLL_ENG_5796.indd 15 2012-12-11 �� 4:38:55 16 Connecting Video Connection Connect the VIDEO OUT (MONITOR) jack on the unit to the video in jack on the TV using a video cable. You can hear the sound through the system’s speakers. Optional Equipment Connection AUX IN Connection Connect an Output of auxiliary device to the AUX (L/R) INPUT Connector. 2 Connecting HT306TQ-F2_DCHNLL_ENG_5796.indd 16 If your TV has only one output for audio (mono), connect it to the left (white) audio jack on the unit. 2012-12-11 �� 4:38:55 Connecting PORT. (Portable) IN Connection Connect an OUTPUT of portable device (MP3 or PMP etc) to the PORT. IN connector. 17 Antenna Connection Connect the supplied FM antenna for listening to the radio. Connect the FM Wire antenna to the FM antenna connector. 2 Connecting MP3 player, etc... USB Connection Connect the USB port of USB Memory (or MP3 player, etc.) to the USB port on the front of the unit. ,,Note Be sure to fully extend the FM wire antenna. After connecting the FM wire antenna, keep it as horizontal as possible. Removing the USB Device from the unit 1. Choose a different function mode or press 停止 (Z) twice in a row. 2. Remove the USB device from the unit. HT306TQ-F2_DCHNLL_ENG_5796.indd 17 2012-12-11 �� 4:38:56 18 System Setting Adjust the Setup settings By using the Setup menu, you can make various adjustments to items such as picture and sound. You can also set a language for the subtitles and the Setup menu, among other things. For details on each Setup menu item, see pages 18 to 22 OSD Initial language settings - Optional 3 System Setting During the first use of this unit, the initial language setup menu appears on your TV screen. You must complete initial language selection before using the unit. English will be selected as the initial language. 1. Press 电源 to turn the unit on. The language setup menu will appear on the screen. To display and exit the Setup Menu 1. Select the DVD/CD or USB function by pressing 功能. 2. Press 设置. Displays the [Setup] Menu. 3. Press 设置 or 返回 to exit in the [Setup] Menu. About help menu for Setup Menu Buttons Operation WS Moving to another menu. A Moving to previous level. Select D Moving to next level or selecting menu. x 返回 To exit the [Setup] menu or [5.1 Speaker Setup]. b 进入 To confirm menu. w/s Move a Prev. d 2. Use WSAD to select a language then press 进入. The confirm menu will appear. 3. Use AD to select the [Enter] then press 进入 to finish the language setup. HT306TQ-F2_DCHNLL_ENG_5796.indd 18 2012-12-11 �� 4:38:56 System Setting LANGUAGE DISPLAY Menu Language TV Aspect Select a language for the Setup menu and then on screen display. Select which screen aspect to use based on the shape of your TV screen. Disc Audio / Disc Subtitle / Disc Menu [4:3] Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu. [16:9] [Original] Refers to the original language in which the disc was recorded. 19 Select when a standard 4:3 TV is connected. Select when a 16:9 wide TV is connected. Display Mode The Display Mode setting works only when the TV Aspect mode is set to 4:3. To select another language, press numeric buttons and then 进入 to enter the corresponding 4-digit number according to the language code list on the page 34. If you enter the wrong language code, press 清除. [Off (for Disc Subtitle)] Turn off Subtitle. HT306TQ-F2_DCHNLL_ENG_5796.indd 19 [Letterbox] Displays a wide picture with bands on the upper and lower portions of the screen. [Panscan] System Setting [Other] 3 Automatically displays the wide picture on the entire screen and cuts off the portions that do not fit. (If the disc/file is not compatible with Pan Scan, the picture is displayed at Letterbox ratio.) 2012-12-11 �� 4:38:56 20 System Setting AUDIO 5.1 Speaker Setup Make the following settings for the built-in 5.1 channel surrounds decoder. 1. Press 设置. 2. Use WS to select AUDIO menu and then press D. 3. Use WS to select [5.1 Speaker setup] menu and then press D. 4. Press 进入 The [5.1 Speaker setup] appears. 3 [Speaker] Select a speaker that you want to adjust. ,,Note Certain speaker settings are prohibited by the Dolby Digital licensing agreement. [Size] Since the speaker settings are fixed, you cannot change the settings. [Volume] System Setting Press AD to adjust the output level of the selected speaker. [Distance] 5. Use AD to select the desired speaker. 6. Adjust options using WSAD buttons. 7. Press 返回 to confirm your selection. Return to the previous menu. After you connected speakers to your unit, set the Distance between the speakers and your listening point if the distance of Center or Rear speakers is bigger than the distance of Front speakers. This allows the sound from each speaker to reach the listener at the same time. Press AD to adjust the Distance of the selected speaker. This distance is equivalent to a difference of the distance between Center or Rear speaker and Front speakers. [Test] Press AD to test the signals of each speaker. Adjust the volume to match the volume of test signals memorized in the system. HT306TQ-F2_DCHNLL_ENG_5796.indd 20 2012-12-11 �� 4:38:56 System Setting 21 DRC (Dynamic Range Control) LOCK (Parental Control) Make the sound clear when the volume is turned down (Dolby Digital only). Set to [On] for this effect. Initial Setting of the Area Code: Vocal When you use this unit for the first time, you have to set the Area Code. Select [On] to mix karaoke channels into normal stereo. 1. Select the [Lock] menu and then press D. This function is effective for multi-channel karaoke DVDs only. HD AV Sync 3. Select the first character using WS buttons. 4. Press 进入 and select the second character using WS buttons. 5. Press 进入 to confirm your Area code selection. Rating Semi Karaoke Blocks playback of rated DVDs based on their contents. Not all discs are rated. When a chapter/ title/ track is fully finished, this function shows the score in the screen with a fanfare sound. 2. Input a password and press 进入. [On] When you finished singing a score will appear on the screen. [Off] Fanfare and score do not appears on the screen. ,,Note yy DVD, DVD Karaoke discs with more than 2 tracks are available discs for the this function. 3 System Setting Sometimes Digital TV encounters a delay between picture and sound. If this happens you can compensate by setting a delay on the sound so that it effectively ‘waits’ for the picture to arrive: this is called HD AV Sync. Use WS (on the remote control) to scroll up and down through the delay amount, which you can set at anything between 0 and 300m sec. 2. Press D. To access the [Lock] options, you must input the password you have created. Input a password and press 进入. Enter it again and press 进入 to verify. If you make a mistake before pressing 进入, press 清除. 1. Select [Rating] on the [Lock] menu then press D. 3. Select a rating from 1 to 8 using the WS buttons. [Rating 1-8] Rating one (1) has the most restrictions and rating eight (8) is the least restrictive. [Unlock] If you select unlock, parental control is not active and the disc plays in full. 4. Press 进入 to confirm your rating selection. yy When you watch movies, “off ” the Semi Karaoke at the SETUP menu or enjoy it without connecting the MIC if the fanfare or score appears during changing a chapter. HT306TQ-F2_DCHNLL_ENG_5796.indd 21 2012-12-11 �� 4:38:56 22 System Setting Password OTHERS You can enter or change password. 1. Select [Password] on the [Lock] menu and then press D. 2. Input a password and press 进入. To change the password, press 进入 when the [Change] option is highlighted. Input a password and press 进入. Enter it again and press 进入 to verify. 3. Press 设置 to exit the menu. ,,Note 3 If you forget your password, you can clear it using the following steps: 1. Press 设置 to display the Setup menu. System Setting 2. Input the 6-digit number “210499” and press 进入. The password is cleared. DivX(R) VOD ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX videos. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration. [Register] Displays the registration code of your unit. Area Code Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 33. 1. Select [Area Code] on the [Lock] menu then press D. 2. Input a password and press 进入. [Deregister] Deactivate your unit and display the deactivation code. ,,Note All the downloaded videos from DivX VOD can only be played back on this unit. 3. Select the first character using WS buttons. 4. Press 进入 and select the second character using WS buttons. 5. Press 进入 to confirm your Area code selection. HT306TQ-F2_DCHNLL_ENG_5796.indd 22 2012-12-11 �� 4:38:56 Operating 23 Basic Operations 1. Insert the disc by pressing 开/关 or connect the USB device to the USB port. 2. Select the DVD/ CD or USB function by pressing 功能. 3. Select a file (or track/ title) you want to play by pressing WSAD. To Stop Press Z Playback Press d Pause Press M Frame-by-Frame Press M repeatedly to play playback title Frame-by-Frame. ,,Note When playing a disc or USB Flash Drive containing with DivX, MP3/ WMA and JPEG files together, you can select menu of files which you would like to play by pressing 菜 单. If “This file has non-supported type on the unit” pops up, select an appropriate file by pressing 菜单. Skipping to the next/ previous chapter/ track/ file Playing repeatedly or randomly Slowing down the playing speed During playback, pressC or V to go to the next chapter/ track or to return to the beginning of the current chapter/ track. Press C twice briefly to step back to the previous chapter/ track. During playback, pressc or v repeatedly to select the required scan speed. To return to normal speed, press 播放. Press 随机/重复 repeatedly, and the current title, chapter or track will be played back repeatedly or randomly. 4 Operating Locating a point quickly by playing a file in fast forward or fast reverse HT306TQ-F2_DCHNLL_ENG_5796.indd 23 Do this - Random play mode : only music files. In the pause mode, press 扫 描 (c or v) to select the required speed. (The reverse playback is not supported on Divx files.) 2012-12-11 �� 4:38:56 24 Operating Other Operations Displaying Disc Information on-screen You can display various information about the disc loaded on-screen. 1. Press 显示 to show various playback information. The displayed items differ depending on the disc type or playing status. 2. You can select an item by pressing WS and change or select the setting by pressing AD. -- Title – Current title number/ total number of titles. -- Chapter – Current chapter number/total number of chapters. 4 -- Time – Elapsed playing time. Operating -- Audio – Selected audio language or channel. To display the DVD Menu r When you play a DVD which contains several menus, you can select the menu you want using the menu. 1. Press 菜单. The disc’s menu appears. 2. Select the menu by using WSAD. 3. Press 播放 to confirm. To display the DVD Title r When you play a DVD which contains several titles, you can select the title you want using the menu. 1. Press 片头. The disc’s title appears. 2. Select the menu by pressing WSAD. 3. Press 播放 to confirm. -- Subtitle – Selected subtitle. -- Angle – Selected angle/total number of angles. -- Sound – Selected sound mode. ,,Note If any button is not pressed for a few seconds, the onscreen display disappears. Selecting a subtitle language ry During playback, press 字幕( ] ) repeatedly to select a desired subtitle language. 1.5 times speed playback r The 1.5 speed allows you to watch the pictures and listen to the sound quicker than playing at a normal speed. 1. During playback, press 播放(d) to play at 1.5 times speed. “dX1.5” appears on the screen. 2. Press 播放(d) again to exit. HT306TQ-F2_DCHNLL_ENG_5796.indd 24 2012-12-11 �� 4:38:56 Operating 25 Starting play from selected time Programmed Playback ry The program function enables you to store your favourite files from any disc or USB device. To start playing at any chosen time on the file or title. 1. Press 显示 during playback. 2. Press WS to select the time clock icon and “--:--:--” appears. 3. Input the required start time in hours, minutes, and seconds from left to right. If you enter the wrong numbers, press 清除 to remove the numbers you entered. Then input the correct numbers. For example, to find a scene at 1 hour, 10 minutes, and 20 seconds, enter “11020” by using numerical buttons. 4. Press 进入 to confirm. Playback starts from the selected time. r This unit memorizes the last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the player or switch off (Stand-by mode) the unit. If you load a disc that has the scene memorized, the scene is automatically recalled. Changing the character set to display DivX® subtitle correctly y If the subtitle does not display properly during playback press and hold 字幕 for about 3 seconds then press AD or 字幕 to select another language code until the subtitle is displayed properly and then press 进入. HT306TQ-F2_DCHNLL_ENG_5796.indd 25 A program can contain 30 tracks/ files. 1. Select the DVD/CD or USB function by pressing 功能. 2. To add a music(s) on the program list, press 编 辑/记忆 to enter the program edit mode ({ mark appears on the menu). 3. Select a desired music on the [List] by using the WS then press 进入 to add the music to the program list. 4. Select music from the program list then press 进入 to start programmed playback. 5. Press 编辑/记忆 to exit the program edit mode ({ mark disappears on the menu). Erasing a file from Program List 4 1. press 编辑/记忆 to enter the program edit mode ({ mark appears on the menu) Operating Last Scene Memory tu 2. Use WS to select the track that you wish to erase from the Program list. 3. Press 清除. Erasing the Complete Program List Use WSAD to select [Clear All] then press 进入. ,,Note The programs are also cleared when the disc or USB device is removed, the unit is switched to power off or the function is switched to others. 2012-12-11 �� 4:38:56 26 Operating Viewing a PHOTO file i This unit can play discs with photo files. i 1. Select the DVD/CD or USB function by pressing 功能. You can listen to music during slide show, if the disc contain music and photo files together. Use WSAD to highlight (~) icon then press 进入 to start slide show. 2. Press WS to select a folder, and then press 进 入. A list of files in the folder appears. If you are in a file list and want to return to the previous folder list, use the WS buttons on the remote to highlight and press 进入. 4 Listening to music during slide show ,,Note This function is available only in disc. 3. If you want to view a particular file, press WS to highlight a file and press 进入 or 播放. While viewing a file, you can press 停止 to move to the previous menu (JPEG menu). Sleep Timer Setting Viewing photo files as a slide show To check the remaining time, press 睡眠. Operating i 1. Use WSAD to highlight ( ) icon then press 进入 to start slide Show. 2. You can change slide show speed using ) icon is highlighted. AD when ( Press 睡眠 one or more times to select delay time between 10 and 180 minutes, after the unit will turn off. To cancel the sleep function, press 睡眠 repeatedly until “SLEEP 10” appears, and then press 睡眠 once again while “SLEEP 10” is displayed. ,,Note You can check the remaining time before the unit turns off. About help menu for slide show Menu w/s / a/d Prev./ Next x Close b Hide Buttons Operation W/S Rotating the picture A/D Moving to another file 返回 Closing the slide show 进入 Hiding the help menu HT306TQ-F2_DCHNLL_ENG_5796.indd 26 Dimmer Press 睡眠 once. The display window will be darken by half. To cancel it, press 睡眠 repeatedly until dimmer gets off. 2012-12-11 �� 4:38:57 Operating 27 Turn off the sound temporarily Press 静音 to mute your unit. You can mute your unit, for example, to answer the telephone, the “MUTE” displayed in the display window. Screen Saver The screen saver appears when you leave the unit in stop mode for about five minutes. System Select - Optional You must select the appropriate system mode for your TV system. If “NO DISC” appears in the display window, press and hold 暂停/步距 (M) for more than five seconds to select a system. VOCAL FADER To cancel it, press 人声消除 again. -- The quality of the VOCAL FADER may be different depending on the recording conditions of music files. Be sure that both FM aerials are connected. (Refer to the page 17) Listening to the Radio 1. Press 功能 until FM appears in the display window. The last received station is tuned in. 2. Press and hold 调台(-/+) for about two seconds until the frequency indication starts to change, then release. Scanning stops when the unit tunes in a station. or Press 调台 (-/+) repeatedly. 3. Adjust the volume by rotating VOL. on the front panel or by pressing 音量 + or - on the remote control repeatedly. 4 Operating You can enjoy the function as karaoke, by reducing singer vocal of music in the various source. (MP3/ WMA/ CD/ etc.) Press the 人声消除, and “FADE ON” will appear in display window. Radio Operations Displaying file information (ID3 TAG ) While playing an MP3 file containing file information, you can display the information by pressing 显示. HT306TQ-F2_DCHNLL_ENG_5796.indd 27 2012-12-11 �� 4:38:57 28 Operating Presetting the Radio Stations You can preset 50 stations for FM. Before tuning, make sure that you have turned down the volume. 1. Press 功能 until FM appears in the display window. 2. Select the desired frequency by using 调台 (-/+). 3. Press 编辑/记忆 a preset number will flash in the display window. 4. Press 预设 (WS) to select the preset number you want. 5. Press 编辑/记忆. The station is stored. 6. Repeat the steps 2 to 5 to store other stations. Deleting all the saved stations 4 1. Press and hold 编辑/记忆 for two seconds. “ERASE ALL” will flash up on the unit display. Operating 2. Press 编辑/记忆 to erase all of the saved radio stations. Improving poor FM reception Press 播放 (d) (MO./ST.) on the remote control. This will change the tuner from stereo to mono and usually improve the reception. HT306TQ-F2_DCHNLL_ENG_5796.indd 28 2012-12-11 �� 4:38:57 Operating 29 Sound adjustment Setting the surround mode This system has a number of pre-set surround sound fields. You can select a desired sound mode by using 音效/ 特效. You can change the 音效/ 特效 using AD arrow key while the 音效/ 特效 information is displayed on. ,,Note yy In some of surround modes, on some speakers, there’s no sound or low sound. it, depends on the mode of surround and the source of audio, it is not defective. yy You may need to reset the surround mode, after switching the input, sometimes even after the sound track changed. The displayed items for the Equalizer may be different depending on sound sources and effects. On Display Description NAT PLUS You can enjoy the natural sound effect same as a 5.1-channel. NATURAL You can enjoy comfortable and natural sound. Regionally optimized equalizer ARABIC/ PERSIAN/ INDIA/ REGUETON/ MERENGUE/ 4 Operating Local Specialization sound effect. (DANGDUT/ SALSA/ SAMBA/ CUMBIA/ AFRO) AUTO EQ POP CLASSIC JAZZ ROCK MP3 OPT BASS Realizes the sound equalizer that is the most similar to the genre of which is included in the MP3 ID3 tag of song files. This program lends an enthusiastic atmosphere to the sound, giving you the feeling you are at an actual rock pop, jazz or classic concert. This function is optimized for compressible MP3 file. It improves the treble sound. During playback, Reinforces the treble, bass and surround sound effect. VIRTUAL You can enjoy more virtual surround sound. NORMAL You can enjoy the sound without equalizer effect. HT306TQ-F2_DCHNLL_ENG_5796.indd 29 2012-12-11 �� 4:38:57 30 Operating Advanced Operations Listening to music from your portable player or external device The unit can be used to play the music from many types of portable player or external devices. 1. Connect the portable player to the PORT. IN(PORTABLE IN) connector of the unit. Or Connect the external device to the AUX connector of the unit. 2 Turn the power on by pressing 电源. 3 Select the PORTABLE or AUX function by pressing 功能. 4 4 Turn the portable player or external device and start it playing. Operating Recording to USB ,,Note yy You can check the recording percentage rate for the USB record on the display window during the recording. (AUDIO, MP3/ WMA CD Only) yy During recording MP3/ WMA, there is no sound. yy When you stop recording during playback, the file that has been recorded at that time will be stored. (AUDIO CD Only) yy Do not remove the USB device or turn off the unit during USB recording. If not, an incomplete file may be made and not deleted on PC. yy If USB recording does not work, the message like “NO USB”, “ERROR”, “USB FULL” or “NO REC” is displayed on the display window. yy Multi card reader device or External HDD can not be used for USB recording. yy A file is recorded by 128Mbyte when you record for a long term. 1. Connect the USB device to the unit. yy When you stop recording during playback, the file will not be stored. 2. Select a DVD/ CD function by pressing 功能. yy You may not store more than 999 files. One track recording - You can record to USB after playing the file you want. All tracks recording - You can record to USB after stop. Program list recording - After showing the programmed list, you can record it to USB. 3. Start the recording by pressing X 录音. yy The numbering of the recording file is entered from the lowest number. So if you delete some of the recording files, the next recording file could be the lowest number among them. yy It’ll be stored as follows. AUDIO CD MP3/ WMA 4. To stop recording, press Z 停止. The other source The making of unauthorized copies of copyprotected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes. Be responsible Respect copyrights HT306TQ-F2_DCHNLL_ENG_5796.indd 30 2012-12-11 �� 4:38:57 Troubleshooting 31 Troubleshooting PROBLEM No power No picture CORRECTION Plug the power cord into the wall outlet securely. Select the appropriate video input mode on the TV so the picture from the unit appears on the TV screen. Connect the video cables securely to both the TV and unit. Select the correct input mode of the unit so you can hear the sound from the unit. There is little or no sound Connect the audio cables into the connection terminals correctly. Replace with a new audio cable. The DVD picture quality is poor Clean the disc using a soft cloth with outward strokes. Insert a disc. A DVD/CD will not play Insert a playable disc (check the disc type, colour system and regional code). Place the disc with the label or printed side facing upwards. Enter your password or change the rating level. 5 Clean the disc using a soft cloth with outward strokes. Move unit and audio components further away from your TV. Check the antenna connection and adjust its position. Radio stations can’t be tuned in properly Attach an external aerial if necessary. Tune to the station manually. Troubleshooting Humming noise heard while a DVD or CD is playing Preset some radio stations, see page 28 for details. The remote is not pointed directly at the unit. Point the remote directly at the unit. The remote is too far from the unit. Use the remote within 23 feet (7m) of the unit. The remote control doesn’t work well / at all There is an obstacle in the path between the remote control and the unit. Remove the obstacle. The battery in the remote control are flat. Replace the battery with new ones. HT306TQ-F2_DCHNLL_ENG_5796.indd 31 2012-12-11 �� 4:38:57 32 Appendix Maintenance Handling the Unit When shipping the unit Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Keeping the exterior surfaces clean yy Do not use volatile liquids such as insecticide spray near the unit. yy Wiping with strong pressure may damage the surface. yy Do not leave rubber or plastic products in contact with the unit for a long period of time. Cleaning the unit To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Notes on Discs Handling Discs Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc. Storing Discs After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. Cleaning Discs Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center to out. Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records. Maintaining the Unit 6 Appendix The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service center. HT306TQ-F2_DCHNLL_ENG_5796.indd 32 2012-12-11 �� 4:38:57 Appendix 33 Area Code List Choose an area code from this list. Area Afghanistan Code Area AF Fiji Code Area Code Area Code FJ Monaco MC Singapore SG SK Argentina AR Finland FI Mongolia MN Slovak Republic Australia AU France FR Morocco MA Slovenia Austria AT Germany DE Nepal NP South Africa ZA Belgium BE Great Britain GB Netherlands NL South Korea KR Bhutan BT Greece GR Antilles AN Spain ES Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK SI Brazil BR Hong Kong HK Nigeria NG Sweden SE Cambodia KH Hungary HU Norway NO Switzerland CH Canada CA India IN Oman OM Taiwan TW Chile CL Indonesia ID Pakistan PK Thailand China CN Israel IL Panama PA Turkey TR Colombia CO Italy IT Paraguay PY Uganda UG Congo CG Jamaica JM Philippines PH Ukraine UA Costa Rica CR Japan JP Poland PL United States US Croatia HR Kenya KE Portugal PT Uruguay UY Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ Denmark DK Libya Ecuador EC Luxembourg Egypt EG Malaysia El Salvador SV Maldives MY Saudi Arabia MV Senegal Ethiopia ET Mexico MX Vietnam RU Zimbabwe SA SN VN ZW 6 Appendix HT306TQ-F2_DCHNLL_ENG_5796.indd 33 LY Russian LU Federation TH 2012-12-11 �� 4:38:57 34 Appendix Language Code List Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu]. 6 Appendix Language Code Language Code Language Code Language Afar 6565 French 7082 Lithuanian 7684 Sindhi 8368 Afrikaans 6570 Frisian 7089 Macedonian 7775 Singhalese 8373 Albanian 8381 Galician 7176 Malagasy 7771 Slovak 8375 Ameharic 6577 Georgian 7565 Malay 7783 Slovenian 8376 Arabic 6582 German 6869 Malayalam 7776 Spanish 6983 Armenian 7289 Greek 6976 Maori 7773 Sudanese 8385 Assamese 6583 Greenlandic 7576 Marathi 7782 Swahili 8387 Aymara 6588 Guarani 7178 Moldavian 7779 Swedish 8386 Azerbaijani 6590 Gujarati 7185 Mongolian 7778 Tagalog 8476 Bashkir 6665 Hausa 7265 Nauru 7865 Tajik 8471 Basque 6985 Hebrew 7387 Nepali 7869 Tamil 8465 Bengali; Bangla 6678 Hindi 7273 Norwegian 7879 Telugu 8469 Bhutani 6890 Hungarian 7285 Oriya 7982 Thai 8472 Bihari 6672 Icelandic 7383 Panjabi 8065 Tonga 8479 Breton 6682 Indonesian 7378 Pashto, Pushto 8083 Turkish 8482 Bulgarian 6671 Interlingua 7365 Persian 7065 Turkmen 8475 Burmese 7789 Irish 7165 Polish 8076 Twi 8487 Byelorussian 6669 Italian 7384 Portuguese 8084 Ukrainian 8575 Chinese 9072 Japanese 7465 Quechua 8185 Urdu 8582 Croatian 7282 Kannada 7578 Rhaeto-Romance 8277 Uzbek 8590 Czech 6783 Kashmiri 7583 Rumanian 8279 Vietnamese 8673 Danish 6865 Kazakh 7575 Russian 8285 Volapük 8679 Dutch 7876 Kirghiz 7589 Samoan 8377 Welsh 6789 English 6978 Korean 7579 Sanskrit 8365 Wolof 8779 Esperanto 6979 Kurdish 7585 Scots Gaelic 7168 Xhosa 8872 Estonian 6984 Laothian 7679 Serbian 8382 Yiddish 7473 Faroese 7079 Latin 7665 Serbo-Croatian 8372 Yoruba 8979 Fiji 7074 Latvian, Lettish 7686 Shona 8378 Zulu 9085 Finnish 7073 Lingala 7678 HT306TQ-F2_DCHNLL_ENG_5796.indd 34 Code 2012-12-11 �� 4:38:57 Appendix 35 Trademarks and Licenses HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation. DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license. Copyrights It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted material without permission. This product features the copy protection function developed by Macrovision. Copy protection signals are recorded on some discs. When recording and playing the pictures of these discs picture noise will appear. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. 6 Appendix HT306TQ-F2_DCHNLL_ENG_5796.indd 35 2012-12-11 �� 4:38:58 36 Appendix Specifications General Power requirements 110 - 240 V, 50/ 60 Hz Power consumption 50 W Dimensions (W x H x D) Approx. 360 x 62.5 x 313 mm without foot Net Weight (Approx.) 2.9 kg Operating temperature 5 °C to 45 °C (41 °F to 113 °F) Operating humidity 5 % to 90 % Outputs VIDEO OUT 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 (Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2 HDMI OUT (video/audio) 19 pin (Type A, HDMI™ Connector) ANALOG AUDIO IN 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1 PORT. IN 0.5 Vrms (3.5 mm stereo jack) System 6 Appendix Laser Semiconductor laser, wavelength: 650 nm Signal system Standard NTSC/ PAL color TV system Frequency response 20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling) Signal-to-noise ratio More than 80 dB Harmonic distortion 0.05 % at 1 W Dynamic range More than 85 dB Bus Power Supply (USB) DC 5 V 0 500 mA Amplifier Stereo mode Surround mode 45 W + 45 W (3 Ω at 1 kHz) Front Center 45 W + 45 W (3 Ω at 1 kHz) Surround 45 W + 45 W (3 Ω at 1 kHz) Subwoofer 105 W (4 Ω at 60 Hz) 45 W (3 Ω at 1 kHz) Tuner FM Tuning Range HT306TQ-F2_DCHNLL_ENG_5796.indd 36 87.5 to 108.0 MHz or 87.50 to 108.00 MHz 2012-12-11 �� 4:38:58 Appendix 37 Front Speaker (Left/ Right) Type 1 Way 1 Speaker Impedance Rated 3Ω Input Power 45 W Max. Input Power 90 W Net Dimensions (W x H x D) 275 x 1 053 x 275 mm Net Weight 2.6 kg Rear Speaker (Left/ Right) Type 1 Way 1 Speaker Impedance Rated 3Ω Input Power 45 W Max. Input Power 90 W Net Dimensions (W x H x D) 275 x 1 053 x 275 mm Net Weight 2.6 kg Centre Speaker Type 1 Way 1 Speaker Impedance Rated 3Ω Input Power 45 W Max. Input Power 90 W Net Dimensions (W x H x D) 200 x 103 x 88 mm Net Weight 0.43 kg 6 Subwoofer 1 Way 1 Speaker Impedance Rated 4Ω Input Power 105 W Max. Input Power 210 W Net Dimensions (W x H x D) 155 x 325 x 265 mm Net Weight 3.12 kg Appendix Type Design and specifications are subject to change without notice. HT306TQ-F2_DCHNLL_ENG_5796.indd 37 2012-12-11 �� 4:38:58 HT306TQ-F2_DCHNLL_ENG_5796.indd 38 2012-12-11 �� 4:38:58
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project