LG NB5630A Owner's manual
ENGLISH
OWNER’S MANUAL
Sound bar
Please read this manual carefully before operating your set and retain it
for future reference.
NB5630A (NB5630A, S73A1-D)
NB5630A-NS_DARELLK_ENG.indd 1
2013-08-23
3:17:12
1
2
Getting Started
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
NB5630A-NS_DARELLK_ENG.indd 2
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
centre. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
2013-08-23
3:17:12
Table of Contents
3
Table of Contents
1
Getting Started
2
Safety Information
4
Unique features
4Introduction
4
– Symbols used in this manual
4Accessories
5
Remote control
7
Front panel
8
Rear panel
9
Mounting the main unit on a wall
1
4Troubleshooting
17Troubleshooting
2
5Appendix
18Specifications
19 Trademarks and licenses
19Maintenance
19 – Handling the unit
3
2Connecting
11
11
11
12
4
Connection and setting up
– Connecting the AC adapter
– OPTICAL In connection
– Pairing wireless subwoofer
5
3Operating
13
13
14
14
15
16
16
16
16
16
16
Basic operations
LG Sound Sync
– AUTO POWER On/Off
Using Bluetooth technology
– Listening to music stored on the
Bluetooth devices
Other operations
– Turn off the sound temporarily
– Adjust the woofer level settings
– 3D Sound effect
– DRC (Dynamic range control)
– Auto power down
NB5630A-NS_DARELLK_ENG.indd 3
2013-08-23
3:17:12
4
Getting Started
Unique features
1
LG Sound Sync
Accessories
Please check and identify the supplied accessories.
Getting Started
Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.
Bluetooth
Remote control (1)
Battery (1)
AC adapter (1)
Power cord (1)
Wall bracket (1)
Wall bracket (2)
WALL BRACKET
INSTALL GUIDE (3)
Optical cable (1)
Enjoys music from bluetooth device with simple
connection.
Introduction
Symbols used in this manual
,,Note
Indicates special notes and operating features.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
Screw (8) & Wall Plug (8)
NB5630A-NS_DARELLK_ENG.indd 4
2013-08-23
3:17:15
Getting Started
Remote control
5
• • • • • • • • • • a • • • • • • • • • •
1 (Power) : Switches the unit ON or OFF.
VOL +/- : Adjusts speaker volume.
? : The button is not available for any function.
: Select Bluetooth function.
OPTICAL: Select Optical function.
? : The button is not available for any function.
• • • • • • • • • • b • • • • • • • • • •
1
Getting Started
(Mute) : Mutes the sound.
WOOFER LEVEL +/- : Sets the sound level of
woofer speaker.
3D SOUND : Turns on and off the 3D Sound mode.
DRC : Sets DRC(Dynamic range control) function.
• • • • • • • • • • c • • • • • • • • • •
AUTO POWER : This function is automatically
turned on the unit.
TV Control buttons: Controls the TV. (LG TV only)
You can control the functions on LG TV : Power,
input source, sound level, channels.
,,Note
yy Once the sound bar is shut down to
standby, please wait several seconds before
trying to use remote again.
yy When you press any button on the remote
control, the red LED on the main unit blinks
twice. (Except 1 (Power) button)
yy The color LED that indicates the current
function is lit up for about 3 seconds
when you press the function buttons : ,
OPTICAL.
yy If the volume level reached a minimum or
a maximum, the red LED on the unit is lit
up when you adjust the volume level of the
sound bar.
yy If the woofer level reached a minimum or
a maximum, the red LED on the unit is lit
up when you adjust the woofer level of the
wireless subwoofer.
NB5630A-NS_DARELLK_ENG.indd 5
2013-08-23
3:17:15
6
Getting Started
Battery Installation
1. Turn the battery cover counterclockwise by
using a coin. Then take the battery cover.
1
Getting Started
Coin
2. Insert and fix the battery with the minus (-)
facing in the same direction as the minus (-) on
the battery compartment.
3. Put the battery cover on the remote control and
turn it clockwise to close.
Warning
DO NOT INGEST BATTERY. CHEMICAL BURN HAZRD
>>Caution
yy The battery used in this device may present
a fire or chemical burn hazard if mistreated.
Do not recharge, disassemble, incinerate,
or heat above 100 °C (212 °F). Replace
the battery part no. CR2025 only. Use of
another battery may present a risk of fire
or explosion. Dispose of used battery.
Keep battery away from children. Do not
disassemble or dispose of in fire.
yy [The remote control supplied with] This
product contains a coin/button cell battery.
If the coin/button cell battery is swallowed,
it can cause severe internal burns in just
2 hours and can lead to death. Keep new
and used batteries away from children. If
the battery compartment does not close
securely, stop using the product and keep
it away from children. If you think batteries
might have been swallowed or placed
inside any part of the body, seek immediate
medical attention.
Coin
>>Caution
If you have long nails, do not open the battery
cover by using your finger. Or else, your nail
would be broken.
NB5630A-NS_DARELLK_ENG.indd 6
2013-08-23
3:17:16
Getting Started
7
Front panel
A
1
Getting Started
B
ARemote sensor
BLED indicator
You can check the current state of the sound bar by the color LED on it. Refer to the table below.
LED Color
LED State
Red
Off
Orange
Green
Power on or disconnected power cord
On
Stand by
-
-
Blink
(Twice per second)
Booting
Bluetooth ready
-
Blink
(Once per second)
Mute
-
-
On -> Off
(After 3 seconds)
-
Bluetooth paired
Optical function
selected
NB5630A-NS_DARELLK_ENG.indd 7
2013-08-23
3:17:16
8
Getting Started
Rear panel
1
A
B
C
Getting Started
D
E
F
AF (Function)
Press it repeatedly to select other function.
B + / - (Volume)
Adjusts speaker volume.
C 1/! (Standby/On).
DShaft
E Optical input
F DC input
>>Caution
Precautions in using the touch buttons
yy Use the touch buttons with clean and dry
hands.
- In a humid environment, wipe out any
moisture on the touch buttons before
using.
yy Do not press the touch buttons hard to
make it work.
- If you apply too much strength, it can
damage the sensor of the touch buttons.
yy Touch the button that you want to work in
order to operate the function correctly.
yy Be careful not to have any conductive
material such as metallic object on the
touch buttons. It can cause malfunctions.
NB5630A-NS_DARELLK_ENG.indd 8
2013-08-23
3:17:16
Getting Started
Mounting the main
unit on a wall
9
SCREEN
1
2. When you mount it on a wall (concrete), use
the wall plugs. You should drill some holes. A
guide sheet (WALL BRACKET INSTALL GUIDE)
is supplied to drill. Use the sheet to check the
point to drill.
Getting Started
Mounting the main unit on a wall, you should
connect all the cables for operating the unit. For
details, refer to the page 11.
You can mount the main unit on a wall.
Prepare screws and brackets.
Main unit
Screw (8) &
Wall Plug (8)
Wall bracket (3)
WALL BRACKET
INSTALL GUIDE (3)
>>Caution
yy The set may be damaged if the set falls
down on its side.
,,Note
Make sure that the triangle mark on the wall
bracket should be facing upwards.
yy Please do not lift the set by holding only
center part alone.
3. Remove the Wall bracket install guide.
yy Please two people should lift the set by
sides when moving it.
4. Fix it with screws as shown in the illustration
below.
1. Fitted with Bracket Center Guide according to
Screen Center and Bottom Line.
NB5630A-NS_DARELLK_ENG.indd 9
SCREEN
2013-08-23
3:17:18
Getting Started
10
,,Note
,,Note
The order of installation wall mount bracket
center screw
The order of installation wall mount bracket
side screw
1
Getting Started
A
BC
D
1. After inserting the C screw adjust the left
and right center.
2. After ensuring the flatness insert B screw.
3.
A, D screw fixation after inserting B, C
screw.
5. Prefixed with bracket left / right guide according
to screen side and bottom line.
6. Remove the wall bracket install guide.
AB
1. Tightening the B screw.
2. Then, aligning the flatness tighten the A
screw.
3. Confirmed the position of the screws after
A , B screw loose while checking flatness.
Screen and wall-bracket position
5%4''0
7. Fix it with screws as shown in the illustration
below.
8. Hang the main unit onto the bracket as shown
below.
NB5630A-NS_DARELLK_ENG.indd 10
2013-08-23
3:17:19
Connecting
11
>>Caution
yy Do not install this unit upside down. It can
damage the parts of this unit or be the
cause of personal injury.
yy Do not hang onto the installed unit and
avoid any impact to the unit.
yy Secure the unit firmly to the wall so that it
does not fall off. If the unit falls off, it may
result in an injury or damage to the product.
2
Connecting
yy When the unit is installed on a wall, please
make sure that a child does not pull any of
connecting cables, as it may cause it to fall.
,,Note
Detach the unit from the bracket as shown
below.
>>Caution
Connection and setting
up
Only use the AC adapter supplied with this
device. Do not use a power supply from
another device or manufacturer. Using any
other power cable or power supply may cause
damage to the device and void your warranty.
Connecting the AC adapter
OPTICAL In connection
Prior to installing the wall mount, first connect the
cable.
Connect the OPT. IN jack on the back of the unit to
OPTICAL OUT jack on the Cinema beam TV using
an OPTICAL cable.
1. Connect the supplied AC power cord to the AC
adapter.
2. Connect the AC adapter cable to DC. IN adapter
input.
3. Plug the AC power cord into an AC outlet.
NB5630A-NS_DARELLK_ENG.indd 11
2013-08-23
3:17:20
12
Connecting
Pairing wireless subwoofer
Manually pairing wireless subwoofer
Setting up the wireless subwoofer
for the first time
When the connection has been failed between the
main unit and the wireless subwoofer, the red LED
on the subwoofer is turned on. To pair them, follow
the steps below.
1. Connect the power cord of the wireless
subwoofer to the outlet. The Yellow-green LED
on the subwoofer starts to blink.
2
1.Press PAIRING on the back of the subwoofer.
The Yellow-green LED on the wireless
subwoofer starts to blink.
Connecting
2. Turn on the main unit. The red LED on it starts to
blink and then the main unit and the subwoofer
will be automatically connected.
2. Press and hold (Volume) on the unit and
(Mute) on the remote control at the same time.
The green LED on the main unit starts to blink.
When connection is completed, the Yellowgreen LED on the subwoofer is turned on and
the green LED on the main unit is lit up for
about 3 seconds.
3. After the Yellow-green LED on the subwoofer
is turned on, press the buttons on step 2 again.
The connection will be completed.
Information of the color LED indicators
State
Sound bar LED
Wireless subwoofer LED
Standby
Red
Red
Initial pairing
Red (Blink)
Yellow-green (Blink)
Pairing
Green (Blink)
Yellow-green (Blink)
Connected
Green [ Off
Yellow-green
Disconnected
Off
Yellow-green (Blink) [ Red
,,Note
yy If you operate main unit then wireless
subwoofer sound within a few seconds in
standby mode.
yy Set the distance between this unit and
wireless subwoofer within 10 m.
yy Optimum performance can be
implemented only when the unit and the
Wireless subwoofer within distance of 2 m
to 10 m is used since communication failure
may occur if longer distance is used.
yy It takes a few seconds (and may take longer)
for the unit and subwoofer to communicate
with each other.
NB5630A-NS_DARELLK_ENG.indd 12
2013-08-23
3:17:20
Operating
Basic operations
LG Sound Sync
You can control some functions of this unit by
your TV's remote control with LG Sound Sync. It
is compatible with the LG TV that is supported LG
Sound Sync. Make sure of the LG Sound Sync logo
on your TV.
Refer to the TV's instruction manual for the details
of LG Sound Sync.
Make one of the following connections, depending
on the capabilities of your equipment.
,,Note
yy You can also use the remote control of
this unit while using LG Sound Sync. If you
use TV's remote control again, the unit
synchronizes with the TV.
With wired connection
1. Connect your LG TV to the unit by using an
optical digital cable. (Refer to the page 11.)
2. Set up LG Sound Sync (Optical) on the TV. Refer
to the TV's instruction manual.
3. Turn on the unit by pressing 1 (Power) on the
remote control.
4. Select OPTICAL function by using OPTICAL on
the remote control.
3
Operating
Controllable function by LG TV's remote control :
Volume up/down, mute.
13
Green LED on the unit is lit up for about 3
seconds and you can listen to the TV's sound.
,,Note
The amount of time to turn off this unit is
different depending on your TV when you set
AUTO POWER function to ON.
yy When the connections failed, make sure of
the condition of the TV and power of it.
yy Make sure of the condition of this unit and
the connection in the cases below when
using LG Sound Sync.
-- Turned off the unit.
-- Changing the function to the others.
-- Disconnecting the optical digital audio
cable.
NB5630A-NS_DARELLK_ENG.indd 13
2013-08-23
3:17:20
14
Operating
AUTO POWER On/Off
This function automatically turns on/off the unit
when you turn on/off the TV or the external device
(DVD Player, Blu-ray Disc Player, etc.) connected to
this unit.
It is supported only on OPTICAL functions.
About Bluetooth
Turn on or off AUTO POWER function by using
AUTO POWER ON/OFF on the remote control.
Bluetooth is wireless communication technology
for short range connection.
,,Note
3
Using Bluetooth
technology
Operating
yy This function is intentionally designed to
turn off the unit after 1 minute of inactivity.
If you did not connect external devices with
optical cable or there is no digital audio
signal going to the unit, the unit will turn off
after 1 minute of inactivity if AUTO POWER
function is turned on.
yy Depending on the connected device, this
function may not operate.
yy It is not available to turn on the unit by
AUTO POWER function if you turn off the
unit directly.
yy On bluetooth function, this unit may
be turned on by AUTO POWER function
depending on the connected bluetooth
device. But in this case, this unit will be
turned off automatically.
NB5630A-NS_DARELLK_ENG.indd 14
The available range is within 10 meters. (The sound
may be interrupted when there is interference by
the other electronic waves which run on same
frequency or if you connect bluetooth devices in
the other rooms nearby.)
Connecting individual devices under Bluetooth®
wireless technology does not incur any charges. A
mobile phone with Bluetooth® wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth® wireless technology.
Available Devices : Mobile phone, MP3, Laptop,
PDA etc.
Bluetooth profiles
In order to use Bluetooth® wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
2013-08-23
3:17:21
Operating
Listening to music stored on
the Bluetooth devices
Pairing this unit and Bluetooth
device
Before you start the pairing procedure, make
sure the Bluetooth feature is turned on in to your
Bluetooth device. Refer to your Bluetooth device’s
user guide. Once a pairing operation is performed,
it does not need to be performed again.
1. Select the Bluetooth function by using on
the remote control. Then the orange LED on the
unit starts to blink.
,,Note
XX:XX means the last four digits of BT
address. For example, if your unit has a BT
address such as 9C:02:98:4A:F7:08, you
will see “LG SOUND BAR (F7:08)” on your
Bluetooth device.
3. Enter the PIN code.
PIN code : 0000
,,Note
Depending on the Bluetooth device type,
some device have a different pairing way.
4. The orange LED is lit up for about 3 seconds
when this unit successfully paired with your
Bluetooth device.
5. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
,,Note
yy You should connect your Bluetooth device
to this unit again when you restart it.
yy The unit connects automatically to the
Bluetooth device which is connected latest,
when you select Bluetooth function again
after changing to the other functions.
yy The sound may be interrupted when
the connection interfered by the other
electronic wave.
yy You cannot control the Bluetooth device
with this unit.
yy Pairing is limited one Bluetooth device per
one unit and multi-pairing is not supported.
yy Although the distance between your
Bluetooth and the set is less than 10 m,
there are obstacles between both, your
Bluetooth device cannot be connected.
yy Depending on the type of the device,
you may not be able to use the Bluetooth
function.
3
Operating
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device
display depending on the type of Bluetooth
device. Your unit appears as “LG SOUND BAR
(XX:XX)”.
15
yy You can enjoy wireless system using phone,
MP3, Notebook, etc..
yy When not connected the Bluetooth, orange
LED is blinking.
yy The Electrical malfunction due to devices
using same frequency such as Medical
equipment, Microwaves or wireless
LAN devices, the connection will be
disconnected.
yy When someone stands and interrupts
communication between Bluetooth device
and the player, the connection will be
disconnected.
yy If the gotten away of the distance between
Bluetooth and the unit, the sound quality
is lower and lower the connection will
disconnect when the space between the
Bluetooth and the unit gets out of the
operating range of Bluetooth.
yy The device with Bluetooth® wireless
technology is disconnected, if you turn off
the main unit or put the device away from
the main unit more than 10 m.
NB5630A-NS_DARELLK_ENG.indd 15
2013-08-23
3:17:21
16
Operating
Other operations
Turn off the sound temporarily
You can mute your unit, for example, to answer the
telephone.
Press on the remote control. Red LED blinks and
there is no sound on the unit.
To cancel it, press again on the remote control or
change the volume level.
3
Adjust the woofer level
settings
Operating
You can adjust the sound level of the wireless
subwoofer. Press WOOFER LEVEL +/- on the
remote control.
,,Note
If the woofer level reached a minimum or a
maximum, the red LED on the sound bar is lit
up when you adjust the woofer level of the
wireless subwoofer.
NB5630A-NS_DARELLK_ENG.indd 16
3D Sound effect
3D Sound features deliver sound creating a
wider spot so you can enjoy more immersive and
cinematic surround sound.
Turn on or off 3D Sound effect by using 3D SOUND
ON/OFF on the remote control.
DRC (Dynamic range control)
Make the sound clear when you feel the volume is
too low.
Turn on or off DRC by using DRC ON/OFF on the
remote control.
Auto power down
This unit will turn itself off to save electric
consumption in the case were main unit is not
connected to external device and is not used for 25
minutes.
But the unit can turns on automatically based on
the [AUTO POWER] function you've set.
2013-08-23
3:17:21
4Troubleshooting
Troubleshooting
17
Troubleshooting
PROBLEM
No Power
No sound
No woofer sound
CAUSE & CORRECTION
yy The power cord is unplugged.
Plug in the power cord.
yy Check the condition by operating other electronic devices.
yy Incorrect input source is selected.
Check the input source and select the correct input source.
yy The mute function is activated.
Press or adjust the volume level to cancel the mute function.
yy The power cord of woofer is not connected.
Plug the power cord into the wall outlet securely.
yy Pairing between the unit and woofer gets disconnected.
Connect the unit and woofer. (Refer to the page 12.)
yy The remote control is too far from the unit.
Operate the remote control within about (7 m).
4
Troubleshooting
The remote control
does not work
properly.
yy There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
yy The battery in the remote control is exhausted.
Replace the battery with new one.
The Auto power on/
off function does not yy Depending on the connected device, this function may not operate.
work.
Check the details below and adjust the unit according to them.
yy Switch [ON] state of DRC function to [OFF] by using remote controller.
yy With the sound bar connected with TV, change the AUDIO DIGITAL OUT setting
When you sense that
on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM].
outputted sound of
y
With the sound bar connected with Player, change the AUDIO DIGITAL OUT
y
the unit is low.
setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or
[BITSTREAM].
yy Change Audio DRC setting on Player setup menu to [OFF] state.
NB5630A-NS_DARELLK_ENG.indd 17
2013-08-23
3:17:21
18
Appendix
Specifications
General
Power requirements
Refer to the main label on the main unit.
Power consumption
Refer to the main label on the main unit.
Dimensions (W x H x D)
(2240 x 52 x 27.7) mm
Net Weight (Approx.)
2.62 kg
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Inputs
DIGITAL IN (OPTICAL IN)
3.0 Vrms (p-p), Optical jack
Amplifier
Total output
310 W
Stereo mode
80 W + 80 W (4 Ω at 1 kHz)
Wireless subwoofer
150 W (3 Ω at 80 Hz)
THD
10 %
5
Wireless subwoofer
Appendix
Power requirements
Refer to the main label on the wireless subwoofer.
Power consumption
Refer to the main label on the wireless subwoofer.
Type
1 Way 1 Speaker
Impedance
3Ω
Rated Input Power
150 W
Max. Input Power
300 W
Net Dimensions (W x H x D)
(296 X 332 X 296) mm
Net Weight
7.64 kg
yy Designs and specifications are subject to change without prior notice.
NB5630A-NS_DARELLK_ENG.indd 18
2013-08-23
3:17:21
Appendix
Trademarks and
licenses
19
Maintenance
Handling the unit
When shipping the unit
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0 Channel is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
Bluetooth® wireless technology is a system which
allows radio contact between electronic devices
within a max. range of 10 meters.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
5
Appendix
Connecting individual devices under Bluetooth®
wireless technology does not incur any charges.
A mobile phone with Bluetooth® wireless
technology can be operated via the Cascade if
the connection was made via Bluetooth® wireless
technology.
yy Do not use volatile liquids such as insecticide
spray near the unit.
The Bluetooth® word mark and logos are owned
by the Bluetooth® SIG, Inc. and any use of such
marks by LG Electronics is under license.
Other trademarks and trade names are those of
their respective owners.
NB5630A-NS_DARELLK_ENG.indd 19
2013-08-23
3:17:22
NB5630A-NS_DARELLK_ENG.indd 20
2013-08-23
3:17:22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement