LG F1203TDS Owner's manual

Add to my manuals
2 Pages

advertisement

LG F1203TDS Owner's manual | Manualzz
Remove Packaging
• The appliance is fitted with transit bolts to prevent internal
damage during transport. Be careful, heavy load!
• Packing and all transit bolts must be removed before using
the washing machine.
• When unpacking the base, be sure to remove the additional
packing support in the middle of the base packing.
original packing for future move.
i Store
Dispose of packing material according to local regulations.
2
Transit bolts
Schraubenschlüssel
1
3
To prevent internal damage during transport, the
special 4 bolts are locked.
If they are not removed, it
may cause heavy vibration, noise and machine to
malfunction.
Unscrew the 4 bolts
2
Remove the 4 bolts
along with the rubber
bungs by slightly
twisting the bung.
6
Electrical connection
4
Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person
to prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
CAUTION about positioning the appliance
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
• Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
• If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
• The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
BS Plug Safety Details (For U.K. User)
This appliance must be earthed As the colours of the wires in the mains lead of
this apparatus may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows: The green and yellow wire must be
connected to the terminal in the plug marked E or by the earth symbol
or
coloured green or green and yellow. The wire coloured blue must be connected to
the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal
marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
CAUTION about the power cord
CAUTION
The appliance is not intended for use by young children or infirm persons without supervision.
Young Children should be supervised to ensure that they do not play with appliance.
4
3. Die 4 Schrauben
lösen und die
using the spanner
supplied. etwas drehen, um sie
Gummipfropfen
zusammen mit den Schrauben abzunehmen.
Die 4 Schrauben und den Schraubenschlüssel
für späteren Gebrauch aufbewahren.
Close the holes with
the caps supplied.
5
Connecting water supply hose
• The drain hose should not be placed higher than 100 cm above the floor.
The hose supplied with the machine must be used. Old hoses may not be reused
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)
• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.
If the water supply pressure is more than 1000kPa, a decompression
device should be installed.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic film, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.
CAUTION about the floor surface
7
Level adjustment
• Proper level-adjustment of the washing machine prevents excessive noise and vibration.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
Level floor: Permissible floor gradient under entire washing machine
is 1˚ .
Additional Clearance: For wall, floor and door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or store laundry products on top of the washing machine at any times. They can damage
the finish or controls of the machine.
We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the specifications of this owner‘s manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the
cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.
Don’t strip or crossthread when connecting inlet hose to the valve.
• Die Transportsicherungsschrauben müssen vor
and the spanner for the future use. Refit transit bolts before transporting the appliance.
i Keep the 4 bolts
jedem Transport des Geräts wieder angebracht
werden.
3
Requirements for installation site
4. Die Schraubenbohrungen mit den
beiliegenden Kappen verschließen.
5 within 100 cm of either side of location of
Power socket: Must be
washing machine. Do not overload the socket with more than one
appliance.
Safety instructions for use
Safety instuctions for the installation
Installation of drain hose
60 - 100 cm
1
•
•
•
•
Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks.
Make sure the connection to taps is tight enough.
Periodically check the condition of the hose and replace the hose if necessary.
Make sure that there is no kink on the hose and that it is not crushed.
connection water leaks from the hose, repeat the same steps. Use the most conventional
i Iftypeafterof completing
tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting
the tap into the adaptor.
Adjustable feet
Adjustable feet
• If the floor is uneven, adjust feet as required.
(Do not insert pieces of wood etc. under the
feet). Make sure that all four feet are stable
and resting on the floor. Then check that
the appliance is perfectly level. (Use a spirit
level).
•
•
•
•
•
•
•
The installation surface must be clean, dry and level.
Install washing machine on a flat hard floor.
Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
The washing machine must be perfectly level and firmly in position.
It must not “see-saw” across corners under load.
The installation surface must be clean, free from floor wax and other lubricant coatings.
Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
@
Technical Specification
Front loading washing machine
Max. Watt
2100 W (Wash) / 1100 W (Steam)
Power supply
220~240 V~, 50 Hz
Wash capacity
8 kg
Size WxDxH mm:
600 x 590 x 850
Water consumption
52 ℓ (6.5 ℓ / kg)
Weight
63 kg
Permissible water pressure 1.0-10 bar (100-1000kPa)
Troubleshooting
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the
operating instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner
always receives these operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only
with cold drinking water and only for washing textiles with washing detergents designed for washing machines. Every
other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug
- never disconnect by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or
parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized
customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive
substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in
fire or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been used then make sure that the solvent has been carefully washed out before inserting the clothes into
the appliance. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly
inflammable gas. Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of
scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement
parts.
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in
order to protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
Disposal
Name of product
N
• When this crossed-out wheeled bin symbol is attached to a product it means the product is
covered by European Directive 2002/96/EC.
• All electrical and electronic products should be disposed of separately from municipal
waste stream via designated collection facilities appointed by the government or the local
authorities.
• The correct disposal of your old appliance will help prevent potential adverse consequences
for the environment and human health.
• For more detailed information about disposal of your old appliance, please contact your city
office, waste disposal service or the shop where you purchased the product.
• Water supply is not adequate in area
• Water supply taps are not completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are clogged.
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information,
please refer to “Cleaning the drain pump filter”
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
• Is the door opened or not
completely closed?
Owner‘s Manual
F1403TDS(1~9)
F1203TDS(1~9)
Close the door completely.
If “
”is not released, call for service.
Unplug the power plug and call for service.
• Water overfills due to the faulty water
valve.
• Water level sensor has malfunctioned.
Close the water tap.
Unplug the power plug.
Call for service.
• Over load in motor.
• Water leaks
Call for service.
• The washer experienced a power failure.
Restart the cycle.
Rattling and clanking noise
Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound
Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise
Have all transit bolts and packing been removed?
Water leaks.
Check and tighten hose connections. Unclog drain pipe.
Contact plumber if necessary.
Excessive suds
Too much detergent or unsuitable detergent.
Washing machine does not start
Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin
Check that the door is firmly shut.
Door does not open
Once started, the door can not be opened for safety reasons.
Wait one or two minutes before opening the door to allow the electric
locking mechanism time to release.
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.
For the U.K. customer
CUSTOMER SERVICES Tel. : +44-(0) 844 847 LGLG(5454) Fax. : +44-(0) 844 847 1413
LGEUK SERVICE WEB-SITE : http://www.lge.co.uk
P/No. :MFL59755582
Preparation
Washing symbols
CHECKING THE MACHINE
Never use a defective machine! In case of any
failure, first unplug the machine and turn off the
water tap.
WATER CONNECTION
Turn on the water tap
INSERT PLUS INTO THE MAINS SOCKET
Never touch the plug with wet hands!
Never remove the plug from the
socket by pulling on the cord.
DOING LAUNDRY AND USING MACHINE
WITH CARE
- empty all pockets
- remove all metal parts
- place the delicate textiles into the laundry net
- close zippers
LAUNDRY WITH DIFFERENT AMOUNTS OF
SOILING
- wash new textiles separately
lightly
- do not prewash
- pretreat dirty spots
heavily
- pre wash
WATER TREATMENT
- with hardness III water
- use water softening agent
Do not tumble dry
Dry flat
Do not wash
Hot ironing
Hang to dry
Do not bleach
Luke warm ironing
Do not iron
Drip dry
Handy to bleach
Pre Wash
For normal dirty clothes use a small
amount of detergent. Don't pre wash.
Mount the level plate to use fluid detergents.
B
Main Wash
For very dirty clothes fill 1/4 of the
portion of detergent in here and
select a prewashing programm
C
Program
Cotton
Cotton
Quick
Fabric Type
Color fast garments (shirts,
nightdresses, pajamas...)and
lightly soiled white cotton
(underwear)
Lightly soiled clothing and
small loads
Water Temp.
(Option)
60°C
(Cold, 30°C,
40°C, 95°C)
40°C (Cold,
30°C, 60°C)
Synthetic
Polyamide, Acrylic, Polyester
40°C (Cold,
30°C, 60°C)
Baby Care
Lightly soiled baby wear
60°C
(40°C, 95°C)
Allergy
Care
Cotton, underwear, pillow
covers, bed sheets,
baby wear
60°C
Delicate laundry easily
damaged
30°C
(Cold, 40°C)
“Hand wash” marked delicate
and wool laundry
40°C
(Cold, 30°C)
Quick 30
Colored laundry which is lightly
soiled fast
30°C
(Cold, 40°C)
Refresh
Cotton mixed, Polyester mixed
Dress shirts, blouses
No Choose
Delicate
Hand Wash
/Wool
Option
-
Time Delay
Steam Wash
Intensive
Soak
Pre Wash
Crease Care
Rinse+Spin
Medic Rinse
-
Time Delay
Steam Default
Intensive
Crease Care
Rinse+Spin
Medic Rinse
-
Time Delay
Intensive
Crease Care
Rinse+Spin
Maximum Load
2
Control panel
Dispenser
drawer
Less than 6.0kg
Options
C
3
B
Drum
For best results or for cleaner rinsing, select the “Medic Rinse” option.
Turn off tap
- Close water supply
- Clean the machine
- Unplug machine
Less than 4.0kg
Steam Washing and Refresh cycle
Cover cap
Refresh
Allergy Care
Less than 4.5kg
Press and hold
the Option buttons
simultaneously
Baby Care
Cotton
Cotton Quick
Synthetic
Press
Start/Pause
Select the desired
program
press
Start/Pause
1
2
3
Unscrew the water
inlet hose
4
Pull out the water
inlet filter
5
Clean the filter using
a hard bristle brush
Tighten up the inlet
hose
TUB CLEAN is special cycle to clean the inside of the washing machine.
A higher water level is used in this cyle at higher spin speed. Perform this cycle regularly.
Cleaning the drain pump filter
1
6 3 sec.
2
3
4
5
1
2
3
4
5
3. Intensive
• If drum
the laundry is Add
heavily
soiled “Intensive” Power ON with
Empty the
anti-limescale
is effective.
completlyoption
and close
(Calgon) to the main
Then press and
• By selecting the Intensive option, the wash
the door time may be extended,
wash compartment.
depending on the hold Rinse and
Close the disp. drawer
Temp. button
program selected.
Press the
Start/ Pause
button to start Tub
Clean process
After the cycle is
complete, leave the
door open to dry
Open the lower cover Unplug the drain plug.
cap. Drain plug to
Then open the filter
pull out the hose
by turning to the left
Note:
To use programs in the
Steam-Cycle, please press
first the “Steam Wash” button
(see additional programs).
Steam Wash is
Steam Wash is
• For tough stained clothes, underwear, or baby
- For heavily stained clothes, underwear, or baby clothes.
clothes.
is available with Cotton, Synthetic,
- Steam Wash is available with the Cotton, Cotton Quick, Synthetic, Baby Care, and• Steam
AllergyWash
Care programs.
Baby Care program.
- Refresh cycle is always Steam wash.
Refresh cycle is fixed Steam wash.
- Do not load delicates such as wool, silk, and easily discolored clothes.
Program
Temperature
Select the
Spinning speed
Remove laundry
- Open the door
- Remove the laundry
[F1403TDS(1~9)]
Select an Option
Pre Wash / Soak / Crease Care / Rinse + Spin
tu
Select Rinse mode
and Washing temperature
nt
Program
Temperature
Program
Cotton
Cold, 30°C, 40°C, 60°C, 95°C
Baby Care
Cotton Quick
Cold, 30°C, 40°C, 60°C
Refresh
Synthetic
Cold, 30°C, 40°C, 60°C
Allergy Care
How to use Refresh Cycle
il
w
as
hi
ng
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are
washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0806.
Steam Washing features enhance washing performance with low
once before the wash program is started.
pressing the
Steam Wash button, Steam
energy consumption. Refresh cycle reducesBycreases
in clothes.
4. Medic Rinse
Function Can be selected.
Beep on / off
By pressing the Steam Wash button, Steam Function
be selected.
Whencan
Steam
Function is selected, Steam wash
• For high effectiveness or more purity in rinse
) LED lights
When Steam Function is selected, Steam wash ( (
lights on.
up.
operation you can choose Medic Rinse option.
Additional Steps
- Turn the machine off
- Leave door open to
allow drum to dry
Select a
Program
3 items
Notes
Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.
To deactivate:
press and hold
the Option buttons
simultaneously
Remove any
extraneous matter
from the pump filter
After cleaning, turn
the pump filter and
insert the drain plug
Close the lower
cover cap
• To use this option, press the intensive button
Less than 4.0kg
Less than 2.0kg
Tub Clean
H ow to use washer
Available in the Cotton, Cotton Quick, Synthetic, Baby Care, and Allergy Care programs.
Medic Rinse is set by default in the Baby Care program.
2. Steam Wash
The respective temperature indicator will light up.
Cleaning the water inlet filter
6 3 sec.
Medic Rinse
A
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock.
Change to the desired program, whilst in child lock mode:
Turn off the water
tap
If the laundry is heavily soiled “Intensive”option is effective.
- By selecting the Intensive option, the washing duration may be extended,
depending on the program selected.
- To use this option, press the intensive button once before the wash program is started.
Temperature
Turn the machine ON
by pressing the Power button
Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufacture’s care label or instructions when washing.
Intensive: If the laundry is heavily soiled “Intensive” option is effective.
Set program at “Cotton 60°C + Steam Wash + Intensive” option for test in accordance or in conformity with IEC60456 and EN60456.
Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic, and Baby Care program.
Crease Care: If you want to prevent creasing, select Crease Care option.
Medic Rinse: For best results or for cleaner rinsing, you can choose Medic Rinse option. Medic Rinse is set by default in the Baby Care program.
Warning: Keep all washing powder and detergents away from children. Danger of poisoning
Power button
Start / Pause
Rinse
Fill detergent
Refer to the
written information
on the detergent's packing
To activate:
press and hold
the Option buttons
simultaneously
Intensive
Program Cycle
6 3 sec.
2
1
Cleaning and Maintenance
Select this function to lock the buttons on the control panel and to prevent tampering.
6 3 sec.
How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select the program you require.
- Press Time Delay button and set time required.
- Press the Start/Pause button.
Rating
Less than 3.0kg
Child Lock
Additional programs
Setting “Time Delay” determines when machine stops.
Fill the drum
Check the folds of the flexible gasket (grey) and remove any small articles, if any. .
Check inside of the drum and remove any left in items for next wash cycle. .
Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages .
[F1203TDS(1~9)]
- Steam Default
Spinning cycle
Time Delay
Softener
Do not exceed the MAX-Level.
Highly densed softeners are to
be diluted with some water.
Washing program table
Display
ai
ECOLOGICAL WASHING
- make use of the max. washing quantity
- do not “pre wash” if possible
- use short program if possible
Medium hot ironing
Additional programs
Steam Cycle
1
W
DRUM CARE
- remove extraneous objects
- leave door open to dry the drum
- check the rubber seals regularly
Washing temperature
Dispenser drawer
A
HANG UP WASTE WATER HOSE
Hose elbow connection e.g. attach to water tap
Sort the laundry
note washing instruction symbols Degree of soiling Type of textile / colour -
4 additional programs
Time Delay / Steam Wash / Intensive / Medic Rinse
is
Press Start / Pause
to start the washing process
f in
ishe
1
2
d
Select the Refresh
program
Load 3 items or less
and close the door
• Available in Cotton, Synthetic and Baby Care
program.
• Medic Rinse is default in Baby Care program.
The required temperature lamp will light up for
identification.
Refresh
Cotton
60°c (30°c, 40°c, 95°c)
� Refresh cycle
The Beep
on/off function can be set only during the washing cycle.
Temperature
Synthetic
40°c (30°c, 60°c)
• For slightly wrinkled clothes which have
Baby Care
95°c (40°c, 60°c)
been
stored
for anfunction
extended time.
40°C, 60°C,
95°C
To set the Beep
On/Off
follow the below steps.
• This option features upgraded washing
It just makes wrinkled clothes easy to iron
performance
with
low
energy.
(Do
not
load
wet
clothes).
No choose
1. Turn on the washing machine (by pressing the Power button).
• Do not load delicates such as wool, silk, and
• Wrinkles will be reduced.
2. Press�theHow
Start/Pause
button.
60°C easily discolored clothes.
to use Refresh cycle
3. Press1.and
hold the Option and Rinse button simultaneously for three seconds to set Beep on/off
Turn on the washer and select the Refresh program.
function.
2. Load 3 items or less and close the door.
NOTE:
- Steam wash is a highly concentrated and
efficient.Press the
Once
It may seem there is no water inside the
3
4 Start/Pause
drum(normal condition).
- During the
steam cycle the strong steam
button
spray may not be seen through the door
(normal condition).
Press the Steam Wash button
repeatedly until the
- During the steam operation, a spraying sound
required and correct numberwill
of items
is displayed
be heard.
(normal condition)
- Do not try to open the door while operating.
Steam can cause severe burns.
3. Press the Steam Wash button repeatedly until
the Beep
on/off
is set,of the
is memorized even after Power is off.
the desired
andfunction
correct number
itemssetting
is
displayed. Initial display is 2 items
Press the
Steam Wash button
Cleaning the dispenser drawer
1
2
Pull out the
dispenser drawer
3
Clean the dispenser
drawer under flowing water
Cleaning in general
4
Clean inside the
recess with an old
toothbrush
Insert the dispenser
drawer
5 Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry.
Important: Do not use methylated spirits, solvents or similar products.
Exterior
Proper care of your washing machine can extend its service life. The
outside of the machine can be cleaned with warm water and a neutral
non-abrasive household detergent. Immediately wipe off any spillage.
Wipe with damp cloth. Avoid striking the surface with sharp objects. Never
hose down the machine!
Interior
Dry around the washing machine door
opening, flexible gasket and door glass.
Run washing machine through a complete
cycle using hot water. Repeat process if
necessary.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement