LG | DR198H | LG DR198H Owner’s Manual

DR197_198P1-AA4ULLG-ENG
DVD RECORDER
OWNER'S MANUAL
MODEL: DR197
DR198H
Before
connecting, operating
please
read this instruction booklet
or
adjusting this product,
carefully and completely.
POWER: This DVD Recorder
CAUTION
operates
WIRING: This DVD Recorder is
amp mains
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK)
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL
5 amp BS
a
This
lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
triangle
point
is intended to alert the
equilateral
user
to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying
the
mains
1362, BSI
product.
cover
or
ASTA
with
of
supply
type of plug supplied is
suitable
wiring
type fitted. Please refer
plug
a
plug
symbol
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
a
instructions below:
A mains
plug
with bared wires is
pin,
marked with the letter E
use a
5 amp
green and
or
yellow.
fuse, either in the plug,
or
or
If
at the
distribution board.
IMPORTANT: The wires in this mains lead
with the
-
following
BLUE:
are
coloured
coloured in accordance
codes:
NEUTRAL, BROWN: LIVE As the colours of the wires in
-
the mains lead of this DVD Recorder may not
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
not suitable for the
should be removed and
coloured green
or
is fitted,
plug
cover
mains socket.
Do not connect either wire to the earth
with the earth
this
use
removed from the mains lead of this DVD
destroyed.
hazardous if inserted in
to the
always
use
fuse
13
approved
the fuse
replacement
a
plug
Recorder must be
BSI 1363
Never
approved type.
omitted. To obtain
WARNING: A mains
a
replacing
mains sockets in your home, then the
any other
an
supplied
fused at 5 amp. When
contact your dealer. If the
.
within
plug,
with the fuse
NO USER-SERVICEABLE PARTS INSIDE
The exclamation
on a
200-240V~,50/60Hz.
marking identifying
correspond
the terminals in your
with the
plug, proceed
as
follows: The wire which is coloured blue must be connected to the
terminal which is marked with the letter N
or
coloured black. The wire
which is coloured brown must be connected to the terminal which is
marked with the letter L
CAUTION:
Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions.
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from over heating.
The openings should be never be blocked by placing the
product on a bed, sofa, rug or other similar surface.This
product should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided or
the manufacturer's instruction have been adhered to.
coloured red.
or
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
vases, should be
CAUTION
placed
concerning
on
the
as
apparatus.
the Power Cord
Most appliances recommend
dedicated circuit;
they
be
placed
upon
a
That is, a single outlet circuit which powers only that appliance
and has no additional outlets or branch circuits. Check the
page of this owner's manual to be certain.
specification
Do not overload wall outlets. Overloaded wall outlets, loose
damaged wall outlets, extension cords, frayed power cords,
damaged
cracked wire insulation
or
are
conditions could result in electric shock
dangerous. Any of
or fire. Periodically
or
or
these
examine the cord of your appliance, and if its appearance
indicates damage or deterioration, unplug it, discontinue use of
the
CAUTION:
CLASS 2M VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS DEFEATED DO NOT
STARE INTO THE
BEAM OR VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS.
CAUTION:
This
To
product employs
a
Laser
System.
proper use of this product, please read this
owner's manual carefully and retain it for future reference.
ensure
Should the unit
require maintenance,
contact
an
authorized
service center.
Performing controls, adjustments, or carrying out procedures
other than those specified herein may result in hazardous
radiation exposure.
To prevent direct exposure to laser
beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
This
product is manufactured to comply with
the radio interference requirements of EEC
DIRECTIVE 89/336/EEC, 93/68/EEC and
73/23/EEC.
2
appliance, and have the cord replaced with an exact
replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such
as being twisted, kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall outlets, and the point
where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord
plug. When installing the product, ensure that the plug is easily
accessible.
Disposal
of your old
appliance
1. When this crossed-out wheeled bin
symbol is
product it means the product is
covered by the European Directive 2002/96/EC.
All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities
appointed by the government or the local
attached to
2.
a
authorities.
3. The correct
disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For
detailed information about disposal of
appliance, please contact your city office,
waste disposal service or the shop where you
purchased the product.
more
your old
Contents
Playback.............................24-31
.24-27
GeneralPlaybackFeatures
PlayingaDivXMovieFile.................28
.29
PlayinganAudioCDorMP3/WMAfile
ViewingaJPEGFile..................30-31
.
Introduction.............................4-8
.
.
.
.
.
.
.
.
.
.
SymbolUsedinthisManual................4
NotesonDiscs..........................4
.5
RecordableandPlayableDiscs
PlayableDiscs..........................6
RegionalCode..........................6
.
.
.
.
.
.
.
.
.
.
.
RemoteControl.........................8
HookupandSettings....................9-23
RearPanel.............................9
.
.
ConnectingtotheAerial...................9
ConnectionstoYourTV..................10
.11
HDMIconnection(DR198Honly)
ConnectingtoanAmplifier................12
Accessory Audio/Video (A/V) Connections .13-14
AutoSetUp...........................15
UsingtheHomeMenu...................15
InitialSettings..........................16
GeneralOperation....................16
GeneralSettings.....................16-18
AutoProgramming...................16
ProgramEdit........................17
.
.
.
.
.
.
.
.
.
.
.
.
.
.17
TVAspect..........................18
AV2Connection.....................18
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Scan
/
(DR197 only)
PowerSaveMode....................18
FactorySet.........................18
LanguageSettings......................18
AudioSettings.........................19
.19
DolbyDigital/DTS/MPEG.
SamplingFrequency..................19
.19
DRC(DynamicRangeControl).
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.19-20
(Parental Control) Settings
Rating.............................19
.
.
.
.
.
.
.
.
.
.
RecordingSettings......................20
DiscRecordMode....................20
DVRecordingAudio..................20
.20
AV2Recording/AutoChapter.
DiscSettings........................21-22
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
TimeSearch..........................43
DivideOneTitlesIntoTwo................44
.44
CombiningTwoChaptersIntoOne
MovingaPlaylistChapter.................45
HideaChapter/Title.....................45
.
.
.
.
.
.
.
.
ProtectaTitle..........................45
Reference............................46-51
AdditionalInformation....................46
OverwritingRecording.................46
Viewing Title List menu displayed on other
DVDRecordersorPlayers.............46
Playing Your Recordings on Other DVD
.46
Players(FinalizingaDisc).
LanguageCodes.......................47
.
SetPassword/AreaCode.............20
.
.
.
Vocal..............................19
Lock
.
Editing...............................39-45
Title List and Chapter List Menu Overview
.39
VR Mode: Original and Playlist Editing
.40
AddingChapterMarkers.................40
ChangingTitleThumbnails................40
MakingaNewPlaylist....................41
Adding Additional Title/Chapters to the Playlist .41
.42
Deleting an Original or Playlist Title/Chapter
DeletingaPart.........................42
NamingaTitle.........................43
.
Progressive
.
.
.
AutoClockSet/ManualClockSet
.
Recording............................32-38
AboutDVDrecording..................32-33
BasicRecordingfromaTV................34
InstantTimerRecording..................34
.34
Playingwhileyouarerecording
TimerRecording........................35
Timer Recording with VIDEO Plus+ System
.36
Timer
Details
.37
Checking
Recording
.37
RecordingfromanExternalInput
RecordingfromDVInput.................38
.
RemoteControlOperation.................8
.
.
.
.
FrontPanel.............................7
.
.
.
.
.
.
.
.
.
.
.
.
.
AreaCodes...........................47
Controlling
Your TV with the
Supplied
RemoteControl........................48
.
Initialize/Finalize....................21
Troubleshooting......................49-50
Specifications..........................51
DiscLabel/DiscProtect...............22
PBC/AutoPlay.....................22
DivXRegistrationCode...............22
General Explanation of On-Screen Display
.23
.
.
.
3
Introduction
Notes
on
To
ensure proper use of this product, please read this
owner's manual carefully and retain for future
Handling
Discs
Do not touch the
the
reference.
disc
on
by
the
Discs
playback side of the disc. Hold
edges so that fingerprints do not get
the surface. Never stick paper
This manual
information
provides
on
the
or
tape
on
the disc.
operation
and maintenance of your recorder. Should the unit
require service, contact an authorized service location.
About the
"
Symbol Display
"
may appear on your TV display during
operation and indicates that the function explained in
this owner's manual is not available
on
that
specific
media.
Used in this Manual
Symbol
Note:
Indicates
Storing Discs
After playing, store the disc in its case. Do not expose
the disc to direct sunlight or sources of heat and never
leave it in a parked car exposed to direct sunlight.
special
notes and
operating
features.
Tip:
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center out.
Indicates
tips
and hints for
A section whose title has
applicable only
symbol.
are
DVD ALL
RAM
of the
following symbols
represented by the
All DVD discs listed below.
DVD-RW with VR
-RW Video
recording
DVD-RW with Video
DVD+RW disc
-R
DVD-R disc
+R
DVD+R
DVD
one
to the disc
the task easier.
DVD-RAM disc
-RW VR
+RW
making
(DL)
disc
mode
recording
mode
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older
records.
DVD-Video disc
VCD
Video CDs
ACD
Audio CDs
DivX
DivX files
MP3
MP3 files
Moisture Condensation
Never
operate this product immediately after
moving
it from
a
WMA WMA files
Leave it for two
JPEG JPEG files
If you
use
damage
4
vinyl
this
cold location to
or
a warm
three hours without
product
in such
discs and internal
a
parts.
location.
operating
situation, it may
it.
Recordable and
DVD-RW
Playable
Video Disc ReWritable):
be formatted for VR mode
(Digital
DVD-RW discs
These Discs
on
the
Discs
-
can
be recorded
can
on
recording
repeatedly. Recordings
or
Video mode
be
can
recording.
erased, then you
can
record
again
Disc.
same
[VR mode]
Recordings can be extensively edited
Playable only on VR mode compatible players (after finalization)
[Video mode]
Playable on regular DVD players (after finalization)
Limited editing features
DVD-R
Video Disc Recordable)
be recorded only once. After you finalize
DVD-R discs can be only formatted to Video mode.
(Digital
These Discs
-
can
a
DVD-R, you
cannot record
on
it
or
edit it.
Playable on regular DVD players (after finalization)
editing features
Limited
DVD-RAM
DVD-RAM discs
Random Access Memory)
can be formatted for VR mode
These Discs
be recorded
the
(DVD
-
can
on
recording.
repeatedly. Recordings can be erased,
Playable on DVD-RAM compatible players.
Recordings can be extensively edited.
Only DVD-RAM standard Version 2.0, 2.1 and 2.2
You cannot use the cartridge-type DVD-RAM disc
DVD+RW
(Digital
These Discs
on
the
same
Playable
can
Video Disc + ReWritable)
be recorded on repeatedly.
record
again
on
discs
can
be used in this unit.
in this unit.
Recordings
be
can
erased, then you
can
record
again
DVD+RW
on
Recordings
can
(Digital
These Discs
it any
can
Disc.
compatible players (automatically finalization)
playable on DVD+RW compatible players only
edited the title/chapter
The edited contents
DVD+R
then you
Disc.
same
be
are
Video Disc + Recordable)
be recorded only once. After you finalize
can
a
after finalization
DVD+R, you
cannot record
on
it
or
edit
more.
Playable on DVD+R compatible players (after finalization)
Any edited contents are not be compatible on DVD+R compatible players. (Hide, chapter combine,
added chapter mark, etc.)
Limited title/chapter editing features.
DVD+R DL
(Digital
These Discs
Video Disc
be recorded
+
Recordable; Double Layer)
it
or
nearly doubled with double layer DVD+R media, allowing consumers to record
on a single DVD+R disc.
Playable on DVD+R DL compatible players (after finalization)
Any edited contents are not be compatible on DVD+R DL compatible players. (Hide, chapter
combine, added chapter mark, etc.)
Limited title/chapter editing features.
up
edit it any
Storage
can
only
once.
After you finalize
a
DVD+R
DL, you
cannot record
on
more.
space is
to 8.5GB of video
Recommended recordable DVD discs
DVD-R
DVD+R
Mitsubishi
(8x, 16x)
That's (8x, 16x)
Verbatim (8x)
Mitsubishi
--
--
Note: If
a
the
using this recorder.
original recorder.
DVD+RW
Mitsubishi
(4x)
Verbatim (4x)
JVC (4x)
Victor (4x)
Maxell (4x)
DVD-RW/DVD+RW discs is recorded
format the disc
using
DVD-RW
(8x, 16x)
Ricoh (8x, 16x)
Verbatim (8x)
using
So if you want to
a
use
Mitsubishi
(4x)
SONY (4x)
Imation (4x)
Maxell (4x)
Ricoh (4x)
personal computer
the disc
on
this
or
DVD+R(DL)
(2.4x, 8x)
Maxell (2.4x)
Mitsubishi
-
-
-
-
-
other DVD
recorder, you
DVD-RAM
Fujifilm (2x)
Mitsubishi (3x)
Maxell (5x)
recorder, you
cannot
must format the disc
5
Discs
Playable
DVD(8cm/12cmdisc)
Discs such
Video CD
movies that
as
(VCD) (8
VIDEO CDs
or
cm
can
/ 12
be
cm
purchased
or
rented
disc)
CD-Rs/CD-RWs in VIDEO
CD/Super
VIDEO CD format
AudioCD(8cm/12cmdisc)
Music CDs
CD-Rs/CD-RWs in music CD format that
or
CD-R/CD-RW
(8
cm
/ 12
cm
can
be
purchased
disc)
CD-R/CD-RW discs that contain audio
titles, DivX, MP3, WMA,
or
JPEG files.
Notes:
recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some
played on the unit.
Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.
Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal). Doing so may result in malfunctions.
Depending on the recording software & the finalization, some recorded discs (CD-R/RW or DVD±R/RW) may
not be playable.
DVD-R/RW, DVD+R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder
may not play if the disc is damaged or dirty, or if there is dirt or condensation on the Recorder's lens.
If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases
in which it may not play because of the settings of the application software used to create the disc. (Check
with the software publisher for more detailed information.)
This recorder requires discs and recordings to meet certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different types
of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain preexisting conditions (see above) to ensure compatible playback.
Customers should note that permission is required in order to download MP3 / WMA files and music from the
Internet. Our company has no right to grant such permission. Permission should always be sought from the
copyright owner.
Depending
CD-R/RW
on
the conditions of the
(or DVD±R/RW)
discs cannot be
Regional Code
This unit has
the
rear
Notes
a
regional
of the unit
on
or
Regional
code
printed
on
the
rear
of the unit. This unit
a
globe
with
one or more
numbers in it
clearly
match your unit's regional code or the disc cannot play.
If you try to play a DVD with a different regional code from the
6
play only
DVD discs labeled
same as
Codes
Most DVD discs have
play
can
"ALL".
back" appears
on
the TV
screen.
visible
on
the
cover.
This number must
unit, the message "Incorrect region code. Can't
Front Panel
ab
c
d e f g h
i j
klm
a
i
POWER button
Switches the recorder ON
b
or
OFF.
j
Disc Tray
Insert a disc here.
c Display
REC: The recorder is
l
recording.
or a
timer
recording
is
programmed.
Shows the current status of the recorder
:
(clock,
program number,
memorized channels.
through
Remote Sensor
Point the recorder remote control here.
AV IN 4
output of
a
digital
camcorder.
(S-VIDEO IN)
Connect the S-Video
output of
an
external
source
(TV/ Monitor, VCR, Camcorder, etc.).
etc).
m
AV IN 4
(VIDEO
IN/AUDIO IN
(Left/Right))
Connect the audio/video
output of an external
source (Audio system, TV/ Monitor, VCR,
Camcorder, etc.).
Z
(OPEN/CLOSE)
Opens or closes the
disc
tray.
PROGRESSIVE SCAN
Switches the
e
down
Indicates when the recorder is in timer
recording
e
or
Connect the DV
TV: Indicates when the recorder is in TV tuner mode.
d
(V/v)
kDVIN
window
Shows the current status of the recorder.
:
PROG.
Scans up
(DR197)
progressive mode ON
RESOLUTION
Sets the
or
OFF.
(DR198H)
output resolution for HDMI and
COMPONENT/ PROGRESSIVE SCAN VIDEO
OUT
-
-
jacks.
HDMI:
1080i, 720p, 576p, 576i
576p, 576i
COMPONENT:
fN/X(PLAY/PAUSE)
Starts
Pause
press
g
h
playback.
playback or recording temporarily,
again to exit pause mode.
x (STOP)
Stops playback
or
recording.
z (REC)
Starts
recording.
recording time.
Press
repeatedly
to set the
7
VIDEO Plus+
Remote Control
To
:
menu
program
display
the
SUBTITLE
for VIDEO Plus+
System programming.
Changes the input to
use for recording (Tuner, AV1-4,
or DV IN).
AV/INPUT:
0-9 numerical buttons: Selects
numbered
options in a menu.
I.SKIP (INSTANT SKIP): Skips 30
seconds forward during playback.
a
(z):
Starts
recording.
recording
REC MODE: Selects the
mode.
b
THUMBNAIL: Selects
SCAN
picture.
/
(m
M):
Search
forward.
or
PLAY MODE: Selects
mode.
PAUSE/STEP
playback.
playback
SEARCH:
or
(X) : Pause
recording temporarily.
HOME
Displays
CLEAR: Removes
Marker Search
the
a
play
point during
Marker Search
menu on a
DVD disc. Switches between Title
List-Playlist
a
mark
on
the
play the title being
currently being
recorded and also
recorded appears
menu.
and Title
thumbnail
menu.
TIMESHIFT: To
or removes
MENU/LIST: Accesses
List-Original
MARKER: Marks any
a
menu.
c
HOME: Accesses
the disc's Title
Displays
menu, if available.
SKIP(./>):Gotonextor
previous chapter or track.
(N): Starts playback.
STOP (x): Stops playback or
recording.
d
REC
TITLE:
PLAY
c
d
TV Control Buttons: See page
48.
backward
b
( ): Selects a subtitle
language.
ZOOM: Enlarges DVD video
image.
CHP. ADD: Inserts a chapter
marker when playing/recording.
as
PIP.
PIP: Selects PIP function
RESOLUTION
Sets the
on or
off.
(DR198H only):
output resolution for
HDMI.
menu.
b / B / v / V
Selects
an
(left/right/up/down):
option in the menu.
button(s)
is not available.
ENTER
( )
Acknowledges menu selection.
PR/CH (+/-): Scans up or down
through memorized channels.
a
POWER: Switches the recorder
DISPLAY: Accesses On-Screen
ON
Display.
or
OFF.
OPEN/CLOSE
(Z): Opens
closes the disc
tray.
and
by
by
AUDIO
the recorder tuner
or
(
language
):
or
menu.
Selects
an
audio
audio channel.
the TV tuner.
Remote Control
Remote Control
Operation
Point the Remote Control at the remote
sensor
and
Battery
Installation
Remove the
battery
of the Remote
press the buttons.
rear
Caution
batteries with
Do not mix old and
insert two R03
new
batteries. Never mix different
types of batteries (standard, alkaline, etc.).
8
(O)
Removes the
TV/DVD: To view channels
selected
RETURN
correctly.
cover on
the
Control, and
(size AAA)
and
matched
and
Hookup
Settings
Rear Panel
a
ab
cd ef
jk
lmn
gh
i
AERIAL
Connect the aerial to this terminal.
b
c
AV OUT 3
(VIDEO
Connect to
e
AV IN 3
a
output
Set
of
/ AUDIO OUT
IN/AUDIO IN
an
k
external
(Left/Right))
inputs.
l
f
Connect
g
audio out
(Digital
to digital (coaxial)
OPTICAL
RF. OUT
jack)
audio equipment.
signal
from the AERIAL to your
S-VIDEO OUT
m
a
S-Video
Input
TV.
on
EURO AV 1 AUDIO/VIDEO
Connect to
a
TV with SCART
jack.
VIDEO OUT SELECT Switch
Select either COMPONENT
or
RGB
EURO AV1 AUDIO/VIDEO terminal
(Left/Right))
output of an external
source (Audio system, TV/ Monitor, VCR,
Camcorder, etc.).
source.
TV/monitor
Connect the audio/video
COAXIAL
into the power
Passes the
interface for
Top Box, VCR, etc.).
TV with video/audio
(VIDEO
AC Power Cord
Connect to
(Pay-TV decoder,
source
d
j
EURO AV 2 DECODER
Connect the audio/video
Hokupand Setings
Plug
HDMI Connector (Type A)
(DR198H only)
HDMI output providing a high quality
digital audio and video.
i
signal of
depending
on
how you connect the recorder to the TV.
n
COMPONENT/PROGRESSIVE SCAN VIDEO
OUT
(Y
Pb
Connect to
Pr)
a
TV with Y Pb Pr
inputs.
(Digital audio out jack)
digital (optical) audio equipment.
Connect to
h Cooling
fan
Connecting
to the Aerial
Rear of TV
Aerial
SCART INPUT
Remove the aerial cable
from your TV set and
insert it into the aerial socket at the back of the
recorder.
socket
aerial
on
Plug
one
plug
socket
AUDIO INPUT
L
VIDEO
INPUT
R
end of the aerial cable into the TV
the recorder and the other end into the
input
ANTENNA
INPUT
on
R
your TV set.
RF coaxial connection
Connect the RF. OUT
jack on the recorder to the
input jack on the TV using the 75-ohm Coaxial
Cable supplied (R). The RF. OUT jack passes the
signal through from the AERIAL jack.
aerial
Rear of the recorder
9
SCART connection
Connections to Your TV
Make
on
the
When
of the
following connections, depending
capabilities of your existing equipment.
one
using
jacks,
the TV
using
the scart
using
the
set the VIDEO OUT SELECT switch
Tips
Audio
(Left/Right) Connection
on
AUDIO OUT
connect the recorder. Use
recorder's AUDIO OUT
only
one
of the
using
the audio cables
(record deck)
Please refer to the manuals of your TV, VCR,
System or other devices as necessary to
S-Video connection
directly to the
input channel.
not connect the recorder's AUDIO OUT jack to
phono in jack (record deck) of your audio
sure
the recorder is connected
right
(A). Do
jack to
of your audio
connections described below.
IN
jacks of the
jacks on the TV
not connect the
the
phono
in
jack
system.
Connect the S-VIDEO OUT
the recorder to the
S-Video in
S-Video cable
jack
Caution
Component
the TV
on
jack on
using the
(S).
Video connection
TV. Tune the TV to the correct video
Connect the COMPONENT/PROGRESSIVE SCAN
Do
VIDEO OUT
the
system.
--
right
recorder to the audio left and
on
make the best connections.
--
the TV
your TV and other equipment you
wish to connect, there are various ways you could
Make
on
jack on the recorder to the
using the video cable (V).
jack
Connect the left and
Stereo
--
on
Connect the VIDEO OUT
video in
to RGB.
Depending
jacks
Video connection
set the VIDEO OUT
SELECT switch to COMPONENT. When
jack,
jack
in
corresponding
cable (T).
the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT
SCART
Connect the EURO AV1 AUDIO/VIDEO scart
the recorder to the
Do not connect your recorder via your VCR. The
DVD image could be distorted by the copy
protection system.
Rear of TV
S-VIDEO
SCART INPUT
INPUT
VIDEO
INPUT
COMPONENT VIDEO INPUT
Y
Pb
AUDIO INPUT
Pr
jacks on the recorder to the
corresponding input jacks on the TV using
cable (C).
If your television is
an
Y Pb Pr
high-definition or "digital ready"
television,
advantage of the recorder's
progressive scan output for the highest video
resolution possible. If your TV does not accept the
Progressive Scan format, the picture will appear
scrambled if you try Progressive Scan on the recorder.
DR197: Set the Progressive Scan to [ON] on the
setup menu for progressive signal, see page 18.
DR198H: Set the resolution to 576p using
RESOLUTION button for progressive signal.
a
you may take
Note:
S
T
C
V
A
does not work with the
Progressive
scan
connections
(yellow
VIDEO OUT
jack)
or
analog
video
S-VIDEO
connection.
Caution
(DR197 only)
setting for Progressive Scan output is
entered, an image will only be visible on a
Progressive Scan compatible TV or monitor. If you set
Progressive Scan to [ON] in error, you must reset the
Once the
recorder.
First,
remove
the disc in the recorder.
Next,
press STOP (x) and hold it for five seconds before
releasing it. The video output will be restored to the
standard
Rear of the recorder
visible
setting,
on a
Caution
and
a
picture will once again be
analog TV or monitor.
conventional
(DR198H only)
If the resolution is set to
720p or 1080i, the VIDEO
OUT, S-VIDEO OUT and COMPONENT VIDEO OUT
connections
10
are
not available.
HDMI connection
HDMI
TV
compatible
HDMI
(DR198H only)
If you have
a
HDMI TV
to this recorder
using
a
monitor, you
HDMI cable.
or
can
connect it
H
1. Connect the HDMI
HDMI
jack
jack on the recorder to the
HDMI compatible TV or monitor
on a
(H).
2. Set the TV's
source
to HDMI
to TV's Owner's
(refer
Hokupand Setings
manual).
Notes:
If your TV is NOT
capable of handling 96 kHz
sampling frequency, set the [Sampling Freq.] option
to [48 kHz] on the setup menu (See page 19).
When this choice is
your system
so
made, this unit will
convert any 96 kHz
automatically
signals
to 48 kHz
to
HDMI
[PCM]
on
Dolby Digital and
Digital] and [MPEG]
setup menu (See page 19).
the
If your TV is not equipped with DTS decoder, set
the [DTS] options to [OFF] on the setup menu
(See
page
19).
surround, you
compatible
audio
The
To
enjoy
DTS multi channel
must connect this recorder to
receiver via
one
a
of this recorder's
DTS
digital
outputs.
arrow on
up for correct
recorder.
About HDMI
decode them.
can
If your TV is not equipped with
MPEG decoder, set the [Dolby
options
Rear of the recorder
alignment
body
should face
with the connector
on
the
Definition Multimedia
Interface) supports
single digital connection for
Players, Set-Top Boxes, and other AV
use
with DVD
on a
devices.
HDMI
developed to provide the technologies of
(High Definition Contents Protection). HDCP is
to protect digital content transmitted and
was
HDCP
used
received.
HDMI has the
capability to support standard, enhanced,
high-definition video plus standard to multi-channel
or
the cable connector
(High
both video and audio
surround-sound
audio, HDMI features include
uncompressed digital video, a bandwidth of up to 5
gigabytes per second, one connector (instead of several
cables and connectors), and communication between the
AV
source
and AV devices such
as
DTVs.
HDMI, the HDMI logo and High-Definition Multimedia
Interface
HDMI
are
trademarks
licensing
or
registered
trademarks of
LLC.
(Type A)
If there is noise
or
lines
on
the screen,
please
check
the HDMI cable.
Tip
When you connect a HDMI or DVI compatible
device make sure of the followings:
-T ry
:
When you
resolution
Additional Information for HDMI
use
HDMI
connection, you
can
(576i, 576p, 720p, or 1080i)
output using RESOLUTION button.
change
the
for the HDMI
on
-
-
the resolution when the recorder is
connected with HDMI connector may result in
malfunctions. To solve the problem, turn off the
on
again.
on
the HDMI/DVI device
seconds, then switch
this recorder.
The connected device's video
correctly
recorder and then turn it
off the HDMI/DVI device and this
Next, switch
and leave it for around 30
Caution
Changing
switching
recorder.
input
is set
for this unit.
The connected device is
compatible with
720(1440)x576i, 720x576p, 1280x720p, or
1920x1080i video input.
Not all
HDCP-compatible
DVI devices will work with
this recorder.
-
The
picture
will not be
displayed properly
with
non-HDCP device.
11
Connecting
to an
Amplifier
Rear of the recorder
Connecting to an amplifier equipped with two
analog stereo or Dolby Pro Logic ll/
Pro Logic
channel
Connect the Left and
Right
AUDIO OUT
jacks on the
jacks on your
system, using the audio
recorder to the audio left and
amplifier, receiver,
(A).
or
stereo
right
in
cables
Connecting to an amplifier equipped with two
digital stereo (PCM) or to an Audio/
Video receiver equipped with a multi-channel
decoder (Dolby DigitalTM, MPEG 2, or DTS)
channel
1.
Connect
A
X
O
of the recorder's DIGITAL AUDIO
one
OUT
jacks (OPTICAL O or COAXIAL X) to the
corresponding in jack on your amplifier. Use an
optional digital (optical O or coaxial X) audio cable.
2.
You will need to activate the recorder's
output. (See "Audio Settings"
Digital
A
on
page
digital
19).
AUDIO INPUT
connection
provides
the best
sound
you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats
supported by your recorder (MPEG 2,
and DTS). Check the receiver manual
Dolby Digital
and the logos
output will be in
Notes:
If the audio format of the
digital output does not match
capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
Six Channel Digital Surround Sound via digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
the
--To
see
the audio format of the current DVD in the
display, press AUDIO.
This recorder does not perform internal
on-screen
--
decoding
of
DTS sound track. To
a
multi channel
surround, you
recorder to
DTS
a
this recorder's
12
"Dolby",
D
trademarks
symbol
Digital
Licensing agreement, the digital
DTS digital out when DTS audio
stream is selected.
--
Laboratories.
are
"DTS" and "DTS
Caution:
--
Manufactured under license from
Dolby
Logic", and the doubleof Dolby Laboratories.
"Pro
the front of the receiver.
on
Due to the DTS
OPTICAL
DIGITAL INPUT
Amplifier (Receiver)
Multi-channel sound
digital multi-channel
quality. For this
COAXIAL
DIGITAL INPUT
(2 channel)
enjoy DTS
must connect this
compatible receiver
digital audio outputs.
via
one
of
Theater
Digital Out" are
Systems, Inc.
trademarks of
Audio/Video
Accessory
TV
(A/V)
VCR, Cable Box, or
Satellite Tuner, etc.
Connections
Connecting
You
can
watch
PAY-TV/Canal Plus Decoder
a
or
record PAY-TV/Canal Plus
programmes if you connect a decoder (not supplied)
to the recorder. Disconnect the recorder's mains lead
from the mains when
To watch
or
connecting
the decoder.
record PAY-TV/Canal Plus programmes,
set
[AV2 Connection] option to [Decoder] (see page
18) and set the program's [Decoder On/Off] option to
[On] on the Setup menu (page 17).
Tip:
You do not need to turn
signals
on
the recorder to view the
from the connected tuner
on
your TV.
Note:
If you disconnect the recorder's mains lead, you will
signals from the connected
Rear of the recorder
not be able to view the
decoder.
Tip:
You do not need to turn
TV
signals
PAY-TV/Canal Plus
Decorder
the recorder to view the
on
your TV.
Notes:
Pictures
prohibit
SCART AV
on
from the connected tuner
containing copy protection signals
copying cannot be recorded.
that
any
If you pass the recorder signals via the VCR, you
may not receive a clear image on your TV screen.
Be sure to connect your VCR to the recorder and
your TV in the order shown below. To watch video
tapes, watch the tapes through a second line input
on
your TV.
Line
VCR
RECORDER
input
1
TV
Line
input
2
When you record to a VCR from this recorder, do
not switch the input source to TV by pressing the
TV/DVD button
Rear of the recorder
Connecting
jack
Connect
a
VCR
to the EURO AV2 DECODER
or
similar
EURO AV2 DECODER
To watch
or
record the
recording device to
jack of this recorder.
source
the
on
the remote.
If you are using a B Sky B tuner, be sure to connect
the tuner's VCR SCART jack to the EURO AV2
DECODER
jack.
If you disconnect the recorder's mains lead, you will
not be able to view the signals from the connected
VCR
or
tuner.
from EURO AV2
DECODER
jack, set [AV2 Connection] option to [Other
Device] (see page 18) and set [AV2 Record] option to
[Auto], [CVBS] or [RGB] as required (see page 20).
13
ConnectingtotheAVIN3orAVIN4
Jacks
Connect the
input jacks (AV
IN 3, AV IN
4)
on
the
recorder to the audio/video out
accessory component,
using
jacks on your
audio/video cables.
Connecting
Using
a
tapes
Use
Note:
Digital Camcorder
the front
connect
DV
a
DV
panel DV IN jack, it is possible to
digital camcorder and digitally transfer
to DVD.
DV cable (not supplied) to connect the DV
jack of your DV camcorder to the front panel
jack of this recorder.
a
in/out
If you use the S-VIDEO IN jack on the front panel, the
VIDEO IN jack on the front panel is not available.
IN
DV
Note:
This
Jack
of
panel
Accessory Component
(VCR, Camcorder, etc.)
only.
jack
is for connection to DV
It is not
compatible
with
digital camcorder
digital satellite tuners
D-VHS video decks.
AUDIO
OUTPUT
R
DV
L
Digital
Camcorder
DV
IN/OUT
VIDEO
OUTPUT
S-VIDEO
OUTPUT
Rear of
the recorder
14
OR
Front of
the recorder
Front of the recorder
or
Auto Set
Up
Using
After the POWER is
pressed for the first time to turn
resetting the unit, the Initial Setup
Wizard function sets the language, clock and tuner
channels automatically.
on
1.
the unit
Select
or
From the Home Menu
Media for
screen
and
can access
you
all the
of the recorder.
recording
display the Home Menu screen.
viewing mode always when
The unit will be in TV
language for the Setup menu and ondisplay. Use v / V to select a language
the Home
menu
appears.
Use b / B buttons to select
2.
then press ENTER.
want. Sub
options
a
main
option
you
appears.
Hokupand Setings
Use v / V and ENTER buttons to select the sub
3.
option
2.
playback
Press HOME to
1.
a
screen
the Home Menu
you want.
Please check your antenna connections.
Press ENTER to move next step.
To exit the HOME menu, press HOME.
4.
Setup
3.
[Start] option is selected.
The tuner will automatically cycle through all
available channels in the area and place them
Start:
Press ENTER while
Displays Setup
menu.
TV
in
the tuner's memory.
Auto Ch. Scan: See page 16.
PR Edit: See page 17.
Timer Record: See page 35.
Movie
DISC:
Displays Title List menu for recordable disc (page
39)
Displays Movie List menu for DivX disc. (page 28)
-P lays back Video CD or DVD-Video disc (page
24-27).
-
4.
Use v / V to select the Clock Set
option
then
-
press ENTER.
Photo
(See
DISC:
[Auto]:
When Channel auto search is
the actual Time and Date
automatically. (See
[Manual]: Enter the
are
completed
also set
"Auto Clock Set"
page 17.)
necessary information for
on
date and time.
b / B
5.
(left/right): Moves the cursor to the
previous or next column.
v / V (up/down): Changes the setting at the
current cursor position.
Press ENTER to confirm your setting.
Press ENTER while [Close] is highlighted to finish
Music
(See
DISC:
Easy
page
Displays
page
Displays
Photo List
menu
for disc.
menu
for disc.
29)
Music List
Menu
Disc
(See
Manager: Displays
21-22)
the Disc
Settings
menu.
page
Rec. Mode:
mode.
DV
30-31)
(See
Input:
Displays
20)
the
menu
to select the record
page
Set the recorder to the DV
input
mode.
setup.
15
Initial
In this
General
Settings
system, there
menu
are
several ways to
Auto
customize the
settings provided. Most menus consist
of three levels to set up the options, but some require
greater depth for the variety of settings.
General
1.
2.
4.
5.
[Start] option then press
Setup menu appears.
While the desired item is
as
option.
Press B to
7.
Use v / V to select the desired
to
option.
to the third level.
setting
(O) repeatedly
then press
to exit the
menu.
Note:
16
to go back to the
Connecting
type of aerial,
to the Aerial
on
page 9.
previous
1.
Select the
2.
Press B to
3.
[Auto Programming] option.
move
icon is
to the third level.
highlighted.
Press ENTER to
begin the channel search.
automatically cycle through all
channels in the area and place them
The tuner will
ENTER to confirm your selection.
Some items require additional steps.
Press b
shown in
[Start]
selected, press B
Use v / V to select the second desired
Press RETURN
88 TV
channels.
Connect the recorder to the desired
to the second level.
6.
8.
equipped with a frequency
capable of receiving up to
tuner
ENTER.
Use v / V to select the desired
move
synthesized
[Setup] option.
Select
move
Programming
This recorder is
Preparation:
Press HOME and select
The
3.
Operation
Settings
level.
Setup
available
the tuner's memory.
in
Program
You
edit
can
move,
[PR] indicates the selected programme position.
[Seek] Searches for a channel automatically.
Searching stops when the recorder tunes in a
Edit
a
channel
manually (add, delete,
name,
etc.).
channel.
1.
Select
2.
Press ENTER while
The
[Program Edit] option
Program
List
[Ch.] Changes the channel number.
[MFT] Fine tunes the channel to obtain
picture.
is selected.
[Edit]
menu
then press B.
appears.
a
clearer
2. Choose OK then press ENTER to confirm the
setting and returns to the Program List menu.
Hokupand Setings
AV1 Decoder
Sets the EURO AV1 AUDIO/VIDEO
encoded video
1.
Press AV/INPUT while the
is
2.
jack
for
inputting
signals.
[Decoder On/Off] option
highlighted.
Press ENTER
[Decoder] appears on the
display.
again to turn off the setting.
Off: Inputs the signals from the EURO AV1
AUDIO/VIDEO jack. Normally select this.
On: The encoded video signal input from the
EURO AV1 AUDIO/VIDEO jack is output to the
EURO AV2 DECODER jack for decoding.
The decoded signal is then input back through
the EURO AV2 DECODER jack so you can
so
Press ENTER
3.
Use v / V to select
a
PR number then press
ENTER.
4.
Use v / V to select the program
ENTER.
option
then press
[Program Edit] Sets the channel manually. See
"Program Edit" on the bottom.
[Station Rename] Changes the station name.
The display for entering characters appears.
To enter
page 43.
Names can be up to 5 characters long.
[Move] Sorts the programme positions
Program
characters,
List. Press v / V to
the selected
move
setting
to watch
or
record PAY-TV/Canal Plus programmes.
Press ENTER so [Decoder] appears on the
display. Press ENTER again to turn off the
setting.
[NICAM Auto/off] Sets the channels for the
NICAM broadcast. Normally, [NICAM] is lit on
the display. If the sound from NICAM broadcast
is not clear, press ENTER so [NICAM]
disappears.
Press RETURN (O) repeatedly to exit Program
List
You
When Channel auto search is
Time and Date
also set
completed the actual
automatically. If the time
in
is not correct, the clock must be
set
display
manually.
1.
Select
2.
Use v / V to select
[Clock set] option then press
[Auto] option then
B.
press ENTER.
Note:
There
are cases
where the TV station does not
send,
sends wrong date and/or time information and the
recorder sets the incorrect time.
or
If this happens,
manually.
we
recommend that you set the clock
Manual Clock Set
1.
Select
2.
Use v / V to select
Edit
perform a search to select and
channels manually.
When you select [Program Edit] in step
display for setting channels appears.
can
are
the recorder
[Clock set] option then press
[Manual] option
menu.
Program
view PAY-TV/Canal Plus programmes.
the
Sets the channels for the
decoder. You need this
5.
or
Auto Clock Set
on
programme position to a new location.
[Delete] Disables a programme position you do
not need.
[Decoder On/Off]
record
see
B.
then press
ENTER.
store TV
3.
Enter the necessary information for date and time.
(left/right): Moves the cursor to the previous
b / B
4
above, the
or
next column.
v / V
the
setting
Press ENTER to confirm your
setting.
(up/down): Changes
cursor position.
at the
current
1.Useb/Btoselecttheitemandpressv/Vto
change the setting.
4.
17
General
TV
Power Save Mode
Settings (Continued)
You
Aspect
Selects the
aspect ratio of the connected TV (4:3
standard
wide).
or
Letter
[4:3
TV.
screen
Box]
Displays
connecting
picture with bands
portions of the screen.
a
4:3
Scan] Select this when connecting to a 4:3
screen TV. Automatically displays a wide picture on
the entire screen and cuts off the portions that do
not fit.
Select this when
TV
TV with
or
a
connecting
to
a
wide-screen
wide mode function.
AV2 Connection
You
can
connect
a
decoder
or
other device to the
on
the back.
Select [Decoder] if you connect the
recorder's EURO AV2 DECODER jack to a PAY-TV
[Decoder]
Canal Plus decoder.
if you connect
the recorder's EURO AV2 DECODER jack to a VCR
[Other Device]
or
similar
Select
recording
an
economic power save
display window
in the
Power Save Mode is not active.
Power Save Mode is active.
[ON]
Notes:
The encoded television
PREMIERE)
are
signals (CANAL+
or
not decoded in the Power Save
Mode.
The Power Save Mode is not available in the
standby
mode for the timer
recording
and when
power off of the unit after receiving the encoded
television signals (CANAL+ or PREMIERE).
Factory Set
EURO AV2 DECODER socket
or
displayed
on
Pan
[16:9]
is
when the unit is turned off.
to
wide
a
set up the unit into
Nothing
[OFF]
Select this when
the upper and lower
[4:3
can
mode.
[Other Device]
If you need to, you can reset the Recorder to all its
factory settings. Select ''Set'' icon then press ENTER
and auto
setup
menu
will appear,
see
page 15.
Note:
Some
options can
Code)
not be reset.
(Rating, Password,
and Area
device.
Language Settings
Progressive Scan (DR197 only)
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT jacks, but are connecting the
recorder to a standard (analog) television, set
Progressive Scan to [OFF].
If you are using the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT jacks for connection to a TV or
monitor that is compatible with a progressive scan
signal, set Progressive Scan to [ON].
Select
Note:
Progressive
Scan will be disable in the
when the VIDEO OUT SELECT switch
panel
is set to RGB
setup
on
the
menu
rear
position.
a
language
Once the
for
Scan
is
setting
Progressive
output
image will only be visible on a
Progressive Scan compatible TV or monitor. If you set
Progressive Scan to [ON] in error, you must reset the
for the
Setup
menu
and
on-screen
display.
Disc Menu/Audio/Subtitle
[Original]Refers
Caution
the disc
was
to the
original language
in which
recorded.
press STOP (x) and hold it for five seconds before
releasing it. The video output will be restored to the
language, press number
corresponding
4-digit number according to the language code list
in the reference chapter (see page 47). If you make
a mistake while entering number, press CLEAR
repeatedly to delete numbers one by one then
standard
correct it.
entered,
recorder.
visible
18
Menu
Display
an
First,
remove
setting,
on a
and
a
the disc in the recorder.
Next,
picture will once again be
analog TV or monitor.
conventional
[Others]
To select another
buttons then ENTER to enter the
[Off](for
Disc
Subtitle)
:
Turn off Subtitle.
Audio
Lock
Settings
Each DVD disc has
a
(Parental Control) Settings
variety of audio output options.
Output according to the type
Set the recorder's Audio
of audio
system you
use.
Hokupand Setings
Rating
Dolby Digital
Blocks
/ DTS / MPEG
content. Not all discs
[Bitstream]: Select "Bitstream" if you connect the
recorder's DIGITAL AUDIO OUT jack to an amplifier
or
other
equipment
with
a
Dolby Digital,
DTS
or
1.
Select
2.
To
/
3.
Select
[1]
-
and
Sampling Frequency
made, this unit will automatically convert any
to 48 kHz so your system can decode
signals
them.
code you
code. Enter
the v / V buttons.
most restrictions
restrictive.
If you select [No Limit], parental control
is not active and the disc plays in full.
4.
Press ENTER to confirm your
rating
selection.
Note:
made, this unit will pass each type of signal through
scenes
rating for the recorder, all disc scenes with
rating or lower are played. Higher rated
are not played unless an alternate scene is
available
a
on
the disc. The alternative must have the
rating or a lower one. If no suitable alternative
found, playback stops. You must enter the 4-digit
password or change the rating level in order to play
same
DRC
rating using
[8]: Rating
(1) has the
rating eight (8) is the least
If you set
the same
processing.
a
one
If your receiver or amplifier is capable of handling
96 kHz signals, select [96 kHz]. When this choice is
without any further
security
4-digit
a
[No Limit]:
If your receiver or amplifier is NOT capable of
handling 96 kHz signals, select [48 kHz]. When this
96 kHz
Rating, Password and Area Code
input the 4-digit security code
must
it again to verify. If you make a mistake while
entering number, press CLEAR repeatedly to
delete numbers one by one then correct it.
audio.
[Off] (for DTS): If you select "Off", the DTS signal is
not output through the DIGITAL AUDIO OUT jack.
their
then press B.
you created.
If you have not yet entered a
are prompted to do so. Input
MPEG): Select when
connected to a two-channel digital stereo amplifier.
DVDs encoded in Dolby Digital or MPEG will be
automatically downmixed to two-channel PCM
choice is
the
on
rated.
are
[Rating] option
access
features, you
MPEG decoder.
[PCM] (for Dolby Digital
playback
of rated DVDs based
(Dynamic Range Control)
With the DVD
format, you can hear a program's
soundtrack in the most accurate and realistic
is
the disc.
presentation possible, thanks to digital audio
technology. However, you may wish to compress the
dynamic range of the audio output (the difference
between the loudest sounds and the quietest ones).
Then, you may listen
without
losing clarity
to
a
movie at
a
lower volume
of sound. Set DRC to
[ON]
for
this effect.
Vocal
Set Vocal to
DVD is
[ON] only when a multi-channel karaoke
playing. The karaoke channels on the disc will
mix into normal stereo sound.
19
Lock
(Parental Control) Settings
(Continues)
Recording Settings
Set Password
1.
Select
2.
Follow
[Set Password] option
then press B.
shown
"Rating" on page 19.
password, select the [Change],
press ENTER and input the new 4-digit code.
Input it again to verify.
To delete the password, select [Delete] then press
To
step
change
2
as
the
ENTER.
Disc Record Mode
If you forget your 4-digit code
If you forget your password, to clear the current
password,
1.
follow the
Display Setup
procedure
menu
You
below.
then select
an
LP
1 level icon.
2. Use the Number buttons to enter the
can set the picture quality for recording;
(High Quality), SP (Standard Quality),
(Low Quality), EP (Extend Quality).
XP
6-digit
DV
number "210499".
3. Select
[Yes]
password is
Audio
Recording
You need to set this if you have a camcorder using
32kHz/12-bit sound connected to the front panel DV
then press ENTER. The 4-digit
cleared. Enter a new code.
IN
jack.
digital
Some
Area Code
camcorders have two stereo tracks for
audio. One is recorded at the time of
Enter the code of
an area
whose standards
to rate the DVD video
"Area
disc, referring
Codes", page 47.).
1.
Select
[Area Code] option
2.
Follow
step
3.
Select the first character
2
as
shown
were
to the list
used
(See
then press B.
"Rating"
using
on
page 19.
the v / V
buttons.
4.
Shift the
cursor
using
using
second character
5.
B buttons and select the
v / V buttons.
Press ENTER to confirm your
area
code selection.
shooting; the
overdubbing after shooting.
On the Audio 1 setting, the sound that was recorded
while shooting is used.
On the Audio 2 setting, the overdubbed sound is
other is for
used.
AV2
You
Recording
can
video
select the
input signal
type of the signal when recording
from the device connected to the
EURO AV2 DECODER socket.
input signal will automatically
signal received.
[CVBS] Only for recording CVBS input signal.
[RGB] Only for recording RGB input signal.
[Auto]
The video
follow
the video
Auto
Chapter
When
recording in Video mode, chapter markers are
put in specified setting. You can change this interval to
5 minutes
[None], switch
chapter marking altogether with the
[None] setting.
or
off automatic
20
10 minutes. If you select
Disc
Finalize
Settings
DVD-R: The recorder initialize the disc to Video mode.
recordings in place so that the
played on a regular DVD player or
computer equipped with a suitable DVD-ROM drive.
Finalizing a Video mode disc creates a menu screen
for navigating the disc. This is accessed by pressing
The
MENU/LIST
Finalizing
Initialize
disc
If you load a completely blank
initialize the disc.
recording
disc, the recorder will
mode will
always be Video mode.
(DL)/DVD-RAM: The
appears. Select [OK] then press
DVD-RW/DVD+RW/DVD+R
Initialize
menu
will
ENTER. DVD-RW disc is initialized to Video mode.
Also, you
can
reformat the DVD-RW/DVD+RW/
DVD-RAM from the
Setup
1.
Select
2.
Press ENTER while
[Initialize] option
Initialize
3.
menu as
menu
below.
[Start]
a
is selected.
desired mode
(VR
Mode
1.
Select
2.
Press ENTER while
Hokupand Setings
a
[OK] then press ENTER.
few moments to initialize the disc.
menu
[Finalize]
everything
is selected.
appears.
Select [OK] then press ENTER.
The recorder starts finalizing the disc.
Note:
How
long
finalization takes
number of titles
on
DVD+R DL disc
can
on the type of
disc, and the
depends
disc, how much is recorded
Caution
If you want to change the disc format,
recorded on the disc will be erased.
then press B.
[Finalize] option
Finalize
3.
Use b / B to select
a
TITLE.
Once you have finalized a DVD-R and DVD+R disc,
you cannot edit or record anything else on that disc
except DVD+RW. However, you can record and edit
DVD-RW disc by choosing [Unfinalize] option.
or
Mode) then press ENTER.
Confirm message will appear.
For DVD+RWs, go to step 4.
It takes
or
Caution
Video
4.
'fixes' the
be
then press B.
appears.
Use b / B to select
can
on
the
the disc.
take up to 30 minutes to
finalize.
Tips
If you load
a
finalized, you
DVD-RW that has
can
Unfinalize from the Finalize
you
can
already been
by choosing
menu. After doing this,
'Unfinalize' it
edit and re-record onto the disc.
You cannot unfinalize
a
DVD-R and DVD+R
(DL)
disc.
If
[Disc Protect] option
not available. To
is set to
finalize,
set
[ON], the finalize is
[Disc Protect] option to
[OFF].
21
Disc
Settings (Continued)
DivX
We
provide you the DivX VOD (Video On Demand)
registration code that allows you to rent and purchase
videos using the DivX
VOD service. For more
Disc Label
Use this to enter
a name
for the disc. This
name
appears when you load the disc and when you
disc information on-screen.
The disc
display
Select
name can
[Disc Label] option
Press ENTER while
2.
Keyboard
To enter
menu
[Edit]
then press B.
see
in DVD-RAM / DVD+RW / +R disc
set to
or
or
to
[ON]
deleting
of the
Playback Control and refers to special
navigation features that are available on
Video CDs
are
played according
to the
PBC, if
available.
Video CDs
are
played
the
same
way
as
Audio
CDs.
You
Play
set up the unit so a DVD disc automatically
playing whenever the DVD is inserted.
If Auto Play mode is set to On, this unit will search for
title that has the longest playback time and then play
back the title automatically.
can
starts
Note:
The Auto
22
Play
is selected and the
code will appear.
registration
code to
purchase
or
rent the
VOD service at
a
disc for
playback
on
Note:
Video CDs.
Auto
Use the
[View]
then press B.
All the downloaded videos from DivX
PBC stands for
[OFF]
Press ENTER while
download the video onto
PBC
[ON]
(R)] option
this unit.
disc loaded. If you need to unlock the disc to make
edits, select [OFF].
some
DivX
www.divx.com/vod. Follow the instructions and
page 43.
disc,
prevent accidental recording, editing
and
3.
is selected.
VR mode formatted DVD-RW
menus
[About
registration
appears.
characters,
recording
2.
Select
videos from DivX
Disc Protect
When
information, visit www.divx.com/vod.
1.
be up to 32 characters long.
For discs formatted on a different recorder, you will
see only a limited character set.
1.
Registration Code
function may not work for
some
DVDs.
be
played
back
on
this unit.
VOD
can
only
General
Explanation
On-Screen Display
This manual
of
Displaying
You
loaded
operating the
require specific operation or
allow only limited operation during playback. When
this occurs, the symbol
appears on the TV screen,
indicating that the operation is not permitted by the
gives
basic instructions for
recorder. Some DVDs
recorder
or
is not available
Displaying
on
1.
Watching
TV
2.
display
on-screen
various information about the disc
on-screen.
Press DISPLAY
once
to show current status.
Press DISPLAY
once
again
playback
During viewing the TV, press DISPLAY to
display/remove the information displayed
number, station
signal (STEREO, MONO)
displayed differ depending
playing status.
type
or
You
can
Hokupand Setings
to show various
information.
The items
on-screen.
audio
Disc Information
the disc.
Information While
Indicates channel
can
on
the disc
name, and
received by
the tuner.
Indicates the record
mode,
free space, and elapsed
time progress bar.
Indicates disc
name
and format.
3.
change
select
or
an
item
select the
by pressing v / V and
setting by pressing b / B.
For details about each
item,
see
the pages in
parentheses.
(or track) number/total
(or tracks) (page 26)
[Chapter]: Current chapter number/total number
of chapters (page 24)
[Time]: Elapsed playing time (page 26)
[Audio]: Selected audio language (DVD VIDEO
only) or audio channel (page 25)
[Subtitle]: Selected subtitle (page 25)
[Angle]: Selected angle/total number of angles
(page 26)
[Sound]: Selected sound mode (page 27)
[Title]:
Current title
number of titles
Indicates current audio
channel.
Indicates current date and time.
Note:
If no button is pressed
display disappears.
for 10
seconds, the
on-screen
23
Playback
General
Features
Playback
1.
Load your chosen disc in the
tray, with the playback side down.
2.
Starts
menu
3.
To
4.
playback using
the
HOME
(see
page
15).
press STOP
playback,
(x).
The unit records the stopped point, depending on the disc. "Xx" appears
Press PLAY (N) to resume playback (from the scene point). If you press
("x" appears on the screen.), the unit will clear the stopped point.
stop
Press OPEN/CLOSE
Press OPEN/CLOSE
(Z)
(Z)
to
on
the
STOP
screen briefly.
(x) again or unload
the disc
the disc.
remove
to close disc
tray
or
press POWER
(1),
the disc
tray closes automatically and unit
turns off.
Note:
If Parental Control is set and the disc is not within the
entered and/or the disc must be authorized
Buttons
Rating settings (not authorized),
(see "Rating", on page 19).
PAUSE/STEP
(Z)
(X)
Opens
closes the disc
or
All Discs
tray.
press PAUSE/STEP
During playback,
playback.
Press PAUSE/STEP
to
(X) repeatedly
(X)
All Discs
to pause
play
Frame-by-Frame.
Tip:
You
can advance or back up the picture frame-by-frame by
pressing b / B repeatedly during PAUSE mode.
The picture frame-by-frame in reverse is not available for
Video CD.
SKIP
(.
/
>)
During playback, press SKIP (. or >) to go to the next
chapter/track or to return to the beginning of the current
chapter/track.
Press SKIP . twice briefly to step back to the previous
chapter/track.
Tips:
To go directly to any chapter during DVD playback, press
DISPLAY twice and press v / V to select the chapter
icon.
On
Then, input the chapter number or use
Audio CD, to go directly to any track,
an
track number
using
the numbered buttons
b / B.
enter the
(0-9) during
playback.
SCAN
(m
/
M)
During playback, press SCAN (m
required scan speed.
or
M) repeatedly
to
select the
DVD;
Video
5
steps
CD, DivX, Audio CD;
While the
3
steps
is
playback
paused, press
repeatedly to play in slow motion
DVD;
Video
ZOOM
(m
or
M)
steps
CD; 3 steps (Forward only)
During playback or pause mode, press ZOOM to enlarge
image.
x2 size
x4 size
x1 size (normal size)
(x1 size
You can move through the zoomed picture using bBvV
the video
buttons.
24
SCAN
4
→
4-digit
Discs
Operations
OPEN / CLOSE
the
→
→
code must be
General
Features
Playback
Buttons
Operations
PLAY MODE
For
(Continued)
Discs
repeat playback
During playback, press
desired
repeat
PLAY MODE
repeatedly
to select
a
mode.
DVD
(Chapter/Title/Off)
VR mode DVD-RW (Chapter/Title/All/Off)
Video CD, Audio CD (Track/All/Off)
MP3/WMA (Track/Folder/Off)
Notes:
On
must set PBC to [OFF] in
Repeat function. See page 22.
If you press SKIP (>) once during Repeat Chapter
(Track) playback, the repeat playback cancels.
a
Video CD with
Setup
For
menu
to
use
PBC, you
the
the
repeat A-B
During playback, press PLAY MODE repeatedly to select
point A then press ENTER to select point B
Repeats a sequence from point A (Starting point) to point
(End point).
B
For random
playback
During playback, press PLAY MODE repeatedly to display
"RANDOM". The unit automatically begins Random
Playback.To return to normal playback, press PLAY MODE
repeatedly until "NORMAL" appears on the TV screen.
Tip:
SKIP >
By pressing
selects another title
TITLE
If the current DVD title has
on
MENU/LIST
SUBTITLE
AUDIO
during Random playback, the unit
(track) and resumes Random playback.
(
the
screen.
The disc
(
)
)
menu
a
menu, the title
Otherwise, the disc
appears
on
the
menu
menu
appears
may appears.
screen.
During playback, press SUBTITLE then press b
repeatedly to select a desired subtitle language.
/ B
Press AUDIO then press b / B repeatedly to hear
language or audio track.
a
different audio
Note:
Some discs feature both
soundtracks. There is
no
Dolby Digital and DTS
analog audio output when
selected. To listen to the DTS
recorder to
a
soundtrack,
DTS decoder via
one
of the
DTS is
connect this
digital outputs.
See page 12 for connection details.
Press AUDIO then press b / B repeatedly during playback
a different audio channel (STEREO, LEFT or
to hear
RIGHT).
With DVD-RW discs recorded in VR mode that have both
main and
Main
I.SKIP
Bilingual audio channel, you
(L), Sub (R), or Main+sub (L+R).
a
Press I.SKIP
repeatedly during playback
can
to
a
switch among
skip
forward
30 seconds.
25
If
is
The
displayed
DVD
VCD
may be displayed first after
Video CD which contains a menu.
loading
a menu screen
menu screen
DVD
or
Marker Search
a
-RW VR
-RW Video
DVD
DVD
Press TITLE
view, then press ENTER
want to
title/chapter you
start playback.
MENU/LIST to return to the
or
You
to
menu
-R
+R
Marker
a
start
can
playback
To enter
points.
screen.
+RW
VCD
To enter
Usetheb/B/v/Vbuttonstoselectthe
RAM
desired
point
the TV
screen
from up to six memorized
at the
marker, press MARKER
a
the disc. The Marker icon appears
to enter up to six
on
on
briefly. Repeat
markers.
VCD
Use the number buttons to select the track you want
to view.
Press RETURN
to return to the
(O)
To Recall
or
1.
During
disc
search
menu
menu screen.
Menu
for
setting and the exact operating procedures
using the menu may differ depending on the
Clear
disc. Follow the instructions
Setup
the each
on
You may also set PBC to
screen.
(see
menu
page
[OFF]
2.
menu
3.
under
22).
RAM
When
+RW
-R
disc has
a
another title
+R
more
than
Press DISPLAY twice
appropriate
a
To start
1.
+R
title, you
can move
-RW VR
DVD
then
use
is erased from the marker search
menu.
v /
(0-9)
or
b / B to
playing
-RW Video
RAM
+RW
Camera
at any chosen time
on
the disc:
during playback. The time
the elapsed playing time.
Press v / V to select the time clock icon
the
1.
If you enter the wrong numbers, press b / B to
move the under bar (_) to the wrong number. Then
3.
right.
Press ENTER to confirm.
Playback
scenes
recorded at different
angles, you can change
angle during playback.
2.
selected time.
DVD
If the disc contains
Press DISPLAY
Display
start time in
Angle
camera
hours, minutes, and
required
enter the correct numbers.
appears
to
a
during playback.
on
the TV
different
camera
The On-Screen
screen.
Usev/VtoselecttheAngleiconintheOnScreen Display.
Use b / B to select
a
desired
The number of the current
TV
angle.
angle appears
on
the
screen.
starts from the
Tip:
The ANGLE indicator will blink
scenes
recorded at different
angle switching
26
starts from the
Then, press the
DivX
seconds from left to
4.
playback
Or, press CLEAR and the marked
scene.
to
Press DISPLAY twice
Input
clear.
-RW Video
and "-:--:--" appears.
3.
or
Press ENTER and
DivX
during playback
numbered button
search box shows
2.
one
press SEARCH. The marker
on the screen.
title number.
Time Search
-R
DVD
appears
follows:
as
V to select the title icon.
select
-RW VR
playback,
Useb/B/v/Vtoselectamarkedscenethat
marked
to another TITLE
Marked Scene
you want to recall
scene
Moving
a
is
possible.
on
the TV
angles
screen
at
to indicate that
3D Surround
-R
+R
This unit
-RW VR
DVD
can
-RW Video
VCD
produce
RAM
simulates multi-channel audio
effect, which
five
more
speakers, instead of the
speakers normally required to listen to
multi-
Press DISPLAY
1.
Display
home theater
a
the TV
on
+RW
Picture)
-R
+R
-RW VR
DVD
-RW Video
VCD
or
system.
The On-Screen
during playback.
appears
in
(Picture
This function enables you to view the stored stations
in sub picture during playback.
from two
playback
conventional stereo
channel audio from
PIP
RAM
3D Surround
a
+RW
DivX
screen.
Usev/VtoselecttheSoundiconintheOn-
2.
Screen
Display.
Useb/Btoselect"3DSUR".
3.
To turn off the 3D Surround
effect, select
"NORMAL".
Finding
You
using
Locations
directly
Disc
on a
any point on
this function. Use this function
can
video CD is
VCD
access
a
only
while
to the
playing. Playback jumps
On and off
video CD
Press PIP to switch
button
a
point
Input
specified.
1.
on
the sub
picture,
Playbck
press this
to switch it off.
mode selection for sub
picture
input mode for the
this button is pressed, each
picture is displayed as
Press AV/INPUT to select the
Press SEARCH
during playback.
The progress bar appears
sub
the TV
on
Use b / B to find
3.
Press ENTER to confirm the selected
a
start
position
for
starts from the selected
picture. Each time
input mode for the sub
screen.
2.
Playback
again
shown below.
playback.
Tuner→AV1→AV2→AV3→AV4
position.
position.
Program
selection for sub
picture
(+/-) to change the program when sub
picture's input is set to tuner. The selected program
number is displayed on the TV screen. You can
view the selected program by pressing STOP (x).
Use PR/CH
Note:
This function works
only
when
no
marker is
memorized.
Last Condition
Memory
Sub
DVD
picture position change
repeatedly until desired position is
achieved. The sub picture moves clockwise or
Press b / B
This recorder memorizes the
user
settings
for the last
disc that you have viewed. Settings remain in memory
even if you remove the disc from the recorder or
counterclockwise.
switch off the recorder. If you load a disc that had its
settings memorized, the latest stop position is
automatically
recalled.
Notes:
--
--
Settings are stored in memory for use any time.
This recorder does not memorize settings of a disc
if you switch off the recorder before
it.
commencing
to
play
27
a
The recorder
can
files,
Movie List
DivX Movie File
Playing
play DivX files.
requirement"
read "DivX file
1.
Press HOME.
2.
Select
[Movie] option.
3.
Select
a
Before
on
playing
right.
1.
options
Press v / V to select a folder/file on the [Movie
List] menu then press ENTER.
[Movie List] menu options appear.
The menu options displayed differ depending on
the selected media.
media that contains DivX
press ENTER.
The [Movie List]
DivX
menu
file(s)
2.
then
Pressv/V/b/Btoselectanoption,andpress
ENTER.
menu
appears
on
the TV
screen.
[Play] Start playback the
[Open] Opens the folder
selected title.
and
list of files in the
a
folder appears
DivX file
requirement
Available resolution size: 720x576
DivX file extensions:
(W
x
H) pixel
".avi", ".divx"
Playable DivX subtitle: ".smi", ".srt",
(Micro DVD format only)",
".txt (Micro DVD format only)"
Playable Codec format: "DIV3", "MP43", "DIVX",
".sub
4.
Press v / V to select a folder, and press ENTER.
A list of files in the folder appears. If you are in a
file list and want to return to the Folder list, use the
v / V buttons
on
the remote to
and
highlight
press ENTER.
5.
If you want to view a particular
highlight a file and press PLAY
file, press
You
functions. Refer to
variable
can use
playback
v / V to
Audio format:
stop the playback. The [Movie List]
Sampling frequency:
48 kHz (MP3),
within 8
-
within 32
within 8
-
320kbps (MP3),
within 32
DVD±R/RW Format: ISO 9660
of files and
displaying
If the subtitle does not
the DivX subtitle
display properly, please
follow
If the number of the
frames per
screen
2.
Press and hold SUBTITLE about 3 seconds.
not
The
If the file is recorded with
code will appear.
Press b / B to select another
Press PLAY
language
displayed properly.
(N)
to continue
playback.
code until
frame is
not
over
29.97
operate
normally.
If the video and audio structure of recorded file is
interleaved,
only 1-point
*
returns to the
menu screen.
GMC, the unit supports
of the record level.
GMC?
GMC is the acronym for Global Motion
Compensation. It is an encoding tool specified in
MPEG4 standard. Some MPEG4
DivX
or
There
encoders, like
Xvid, have this option.
are
usually
28
192kbps (WMA)
(UDF Bridge format)
(total number
second, this unit may
steps
4.
-
folders)
Press PAUSE/STEP when the subtitle appears.
the subtitle is
(WMA)
DivX format
on
1.
3.
below.
Notes
the
language
48kHz
-
Maximum Files/Disc: Less than 1999
appears.
Notice for
"AC3", "PCM", "MP2",
CD-R Format: ISO 9660 and JOLIET.
Press STOP to
menu
Playable
"MP3", "WMA"
Bit rate:
(N).
pages 24-27.
6.
"XVID", "DX50"
different levels of GMC
called
1-point, 2-point,
or
encoding,
3-point GMC.
Playing
Audio CD
an
or
MP3/WMA
file
1.
The recorder
audio CDs and MP3/WMA files.
play
playing MP3/WMA files,
requirement" on right.
can
Before
file
1.
3.
read "MP3/WMA audio
2.
menu
[Music] option.
Select
a
folder/file
a
List]
menu
then press ENTER.
The
menu
The
menu
options appear.
options displayed
on
differ
options
the
[Music
depending
on
Pressv/V/b/Btoselectanoption,andpress
ENTER.
appears.
Select
Press v / V to select
menu
the selected media.
Press HOME.
The HOME
2.
Audio CD and Music List
Start
[Play]
media that contains MP3/WMA
title then press ENTER.
The [Music List] menu appears
on
or
the TV
[Random]
audio
Start
[Open] Opens
screen.
the selected title.
playback
or
stop random playback.
the folder and
list of files in the
a
folder appears
Random
1.
Press v / V to select
The
2.
menu
options
file then press ENTER.
a
appear.
Press v / V to select
Playbck
then press
[Random] option
ENTER.
4.
Use v/V to select
Playback
You
a
track then press PLAY
can use
variable
playback
functions. Refer to
Press DISPLAY to view
ID3-Tag
information for
the MP3 file. If
ID3-Tag information is not
present, [ID3-Tag: None] will appear. If you
folder, the number of subfolders and
number of MP3/WMA files in the folder
displayed.
3.
To return to normal
option again
Tips:
a
automatically begins
and "RANDOM" appears
pages 24-27.
select
The unit
(N).
starts.
Press DISPLAY
information
to
are
remove
the
move
playback,
To
to the upper
highlight
stop playback
playback
menu screen.
select
[Random]
then press ENTER.
Tip:
during
Random
playback,
unit selects another track and
resumes
Random
By pressing
SKIP >
the
playback.
MP3/WMA audio file
directory,
use
and press ENTER.
".mp3",
requirement
".wma".
Sampling frequency:
within 8 48 kHz (MP3),
-
5.
random
the
File extensions
screen.
If you want to
the v / V to
again
on
at any
time, press STOP.
within 32
48kHz
-
(WMA)
Bit rate:
within 8
-
320kbps (MP3),
within 32
-
192kbps (WMA)
CD-R Format:
ISO 9660 and JOLIET.
DVD±R/RW Format:
ISO 9660
(UDF Bridge format)
Maximum Files/Disc:
Less than 1999
(total
number of files and
folders)
29
a
The recorder
can
JPEG
Photo List
JPEG File
Viewing
JPEG files. Before
play
recordings,
read "Photo file
playing
requirement" on
1.
1.
Press HOME.
The HOME
a
file
the
[Photo List]
differ
depending
on
then press ENTER.
The
menu
The
menu
options appear.
options displayed
on
the selected media.
menu
appears.
2.
Select
[Photo] option.
3.
Select
a
2.
Use v / V to select
an
option
then press ENTER
to confirm your selection.
media that contains JPEG file then press
[Open] Opens
ENTER.
The
options
Press v / V to select
menu
right.
menu
the folder and
a
list of files in the
folder appears
[Photo List]
menu
appears
on
the TV
screen.
[Full Screen]
Shows the selected file
as
full
screen.
[Slide Show] Displays
Slide Show
menu.
Skip Images
While
once
4.
Useb/B/v/Vtoselectafile,thenpress
ENTER.
The
menu
viewing
a
previous
file.
Rotate
Images
Use v / V while
options
appear
on
the left side of the
picture,
press SKIP
to advance to the next file
clockwise
or
viewing
a
or
picture
(.or >)
return to the
to
flip
the
picture
counterclockwise.
menu.
Tips:
If you want to
move
to the upper
v / V to
highlight
You
select all files
can
on
the
the
menu
by pressing
selections, press
files
CD-R Format:
ISO 9660 and JOLIET.
DVD±R/RW Format:
Repeat step
1 to mark additional file.
[Full Screen]
Notes
image
is
displayed
in full
screen.
upon the size and number of JPEG
files, it could take a long time for the recorder to
read the files.
Press ENTER to appear or disappear this
during viewing the full screen.
stop viewing
[Photo List]
at any
menu
(UDF Bridge format)
Less than 1999
then press
Depending
The
ISO 9660
Maximum Files/Disc:
ENTER.
The selected
menu
time, press STOP.
appears.
Tip:
If you press RETURN (O) while menu screen is
displaying, the screen is changed to TV viewing or AV
30
Photo size:
Less than 4MB recommended
Use v / V to select
input.
".jpg"
Press MARKER.
2.
To
requirement
A check mark appears on the file. Press
MARKER again to cancel the marked file.
1.
6.
Photo file
File extensions
again.
Selecting multiple
5.
use
and press ENTER.
CLEAR button. To cancel the
CLEAR
directory,
on
(total
number of files and
JPEG file
Progressive
and lossless
files
supported.
are
folders)
not
compression
JPEG
image
View Slide Shows
1. Select
(Refer
[Slide Show] option
to "Photo List
menu
the [Photo List] menu
options" on page 30).
on
2. Press ENTER.
The Slide Show
menu
appears.
3.Useb/B/v/Vtosettheoptions.
[Object] option:
[Selected] Views
slide show
only
selected files.
Use the MARKER button to select
[All]
multiple
files.
Views slide show all files.
[Speed] option:
Sets the Slide Show
speed
to
[Slow], [Normal],
Playbck
or
[Fast].
4. Select the
[Start] option
then press ENTER to start
the Slide Show.
The slide show continues until you press STOP
5. Press STOP to
the Photo List
stop the Slide Show and
(x).
returns to
menu.
To Pause the Slide Show
1. Press PAUSE/STEP
(X)
to pause slide show.
2. When you want to continue slide
PLAY (N).
show, press
31
Notes for
Recording
About DVD
The
the recorder
recording
Notes:
This recorder cannot make
recordings
on
CD-R
or
CD-RW discs.
Our company takes
failure due to power
no
responsibility
outages,
for
defective
recording
discs,
or
damage to the Recorder.
Fingerprints and small scratches on a disc can
affect playback and/or recording performance.
Please take proper
Disc types and
and
care
of your discs.
recording formats, modes,
settings
This recorder
discs:
play five different kinds of DVD
pre-recorded DVD-Video discs, DVD-RW,
can
DVD-R, DVD-RAM, DVD+RW and DVD+R discs. The
DVD-R, DVD+R, DVD+RW discs is
disc format for
always
"Video format"---the
DVD-Video discs. This
same as
means
that
pre-recorded
once
finalized, you
play a DVD-R, DVD+R, or DVD+RW in a regular
DVD player. The DVD-RAM disc format is Video
Recording (VR) format.
By default, the DVD-RW disc format is Video format,
though you can change this to Video Recording (VR)
format, if required. (Reinitializing the disc will erase
the contents of the disc.)
The recording mode is closely related to the disc
format. If the disc format is Video Recording format,
then the recording mode is VR mode; if the disc
format is Video mode, then the recording mode is
Video mode (except for DVD-Video, which is not
recordable, and so does not have a recording mode).
Within the recording modes (which are fixed for them
whole disc) are the record settings. These can be
changed as required for each recording and
determine the picture quality and how much space the
recording will take up on the disc.
can
recording
recording
times shown
uses
not exact because
are
variable bit-rate video
compression. This means that the exact recording
time will depend on the material being recorded.
When recording a TV broadcast, if the reception is
poor or the picture contains interference, the
recording times may be shorter.
If you record still pictures or audio only, the
recording time may be longer.
The displayed times for recording and time
remaining may not always add up to exactly the
length of the disc.
The recording time available may decrease if you
heavily edit a disc.
If using a DVD-RW disc, make sure you change the
recording format (Video mode or VR mode) before
you record anything on the disc. See page 21
(Initialize) for how to do this.
When using a DVD-R or DVD+R disc, you can keep
recording until the disc is full, or until you finalize the
disc. Before you start a recording session, check
the amount of recording time left on the disc.
When using a DVD-RW disc in Video mode,
recording time available will only increase if you
erase
the last title recorded
The Delete Title
menu
hides the
only
on
the disc.
in the Title List
option
title, it does
the title from the disc and increase
time available
(except
for the last recorded title
DVD-RW disc in Video
Overwrite
recording
(Original)
actually erase
the recording
not
is available
using
DVD+RW
discs.
When
using a DVD+R/RW, the recorder will execute
Menu-making operation to update the new title
and editing when removing the disc from the recorder
the
or
turn off the recorder.
Recording
There
XP
are
four
time and
picture quality
preset recording quality modes:
Highest quality setting, gives about
recording time on a DVD (4.7GB).
SP
Default quality, sufficient for most applications,
gives about 2 hours of recording time on a DVD
(4.7GB).
LP
Slightly lower video quality, gives about 4 hour
of recording time on a DVD disc (4.7GB).
EP
Lowest video quality, gives about 6 hour of
recording time on a DVD (4.7GB).
You may see a fragmented picture during playing
--
1 hour of
--
--
--
back the contents recorded in EP mode
32
on a
mode).
.
Restrictions
on
Copyright
copying
Some video material is copy-once protected: If you
want to record copy-once protected material to DVD,
you must use a VR mode DVD-RW disc
with CPRM Ver. 1.1.
compatible
You
can identify copy-once protected material during
playback by displaying disc information on-screen.
NTSC format
analog or the DV
is
not
recorded
inputs
correctly with this recorder.
Video signals in SECAM format (from the built-in TV
tuner or from the analog inputs) are recorded in PAL
signals
from the
format.
Video that is
using
'copy-once only'
can
DVD-RW disc in VR mode
with CPRM
only
or
be recorded
DVD-RAM disc
(see below).
What is 'CPRM'?
CPRM is
This
product incorporates copyright protection
technology that is protected by method claims
certain U.S.
patents
and other intellectual
of
property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only, unless otherwise
authorized by Macrovision corporation. Reverse
engineering or disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
scramble
copy protection system (with
system) only allowing the recording of 'copy
a
COMPATIBLE WITH THIS PRODUCT AND MAY
once'
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
broadcast programs. CPRM stands for Content
Protection for Recordable Media.
This Recorder is CPRM
Recording equipment should be used only for lawful
copying and you are advised to check carefully what
is lawful copying in the area in which you are
making a copy. Copying of copyright material such
as films or music is unlawful unless permitted by a
legal exception or consented to by the rights owner.
compatible,
which
PICTURE. IN CASE OF 625 PROGRESSIVE SCAN
means
that
PICTURE
PROBLEMS, IT IS RECOMMENDED
record copy-once broadcast programs, but
you cannot then make a copy of those recordings.
CPRM recordings can only be made on DVD-RW
THAT THE USER SWITCH THE CONNECTION TO
discs formatted in VR mode
SET COMPATIBILITY WITH THIS MODEL
you
can
CPRM
are
or
DVD-RAM
discs, and
recordings can only be played on players
specifically compatible with CPRM.
that
THE 'STANDARD DEFINITION' OUTPUT. IF
THERE ARE QUESTIONS REGARDING OUR TV
DVD
625p
RECORDER, PLEASE CONTACT OUR
CUSTOMER SERVICE CENTER.
33
Basic
Recording
from
TV
a
Follow the instructions below to record
Instant Timer
TV program.
until the
a
immediately and continues
you stop the recording.
Recording
starts
disc is full
or
Instant Timer Recording allows you to make a
recording easily of a preset length without using
Follow
steps
from
TV).
1.
1.
Set
2.
Use PR/CH
a
REC
recordable disc for DVD
a
mode
recording.
time
as
a
Press REC
2.
recording
necessary by pressing
MODE repeatedly. (XP, SP, LP, EP)
(+/-)
the
program timer.
Note:
You must load
Recording
1-2
as
shown left
(z) repeatedly
(Basic Recording
to select the
recording
length.
buttons to select the TV channel
to record.
Recording starts after the first press. Each
subsequent press increases the recording time
Changing TV Audio Channel
You
can
select the audio channel
by pressing
(language) to
during viewing TV program.
channel is displayed on-screen.
AUDIO
current audio
listen
within free space.
The recording time is
The
At the end of the
Stereo broadcast:
Stereo
→
Bilingual
Main
→
Left
broadcast:
Sub
If the sound is of poor quality when set to Stereo,
you can often improve it by changing to Mono (Left
or
Right).
Recording
Press REC
once
recalled
will
(z)
setting
for
screen
a
the TV
record either NICAM
can
audio. If the NICAM
or
regular
setting (page 17)
is set to
then if the broadcast is
NICAM, the audio
automatically changes
to NICAM and you
Time
to check the
automatically
recording
window.
display
The
non-
NICAM sound distortion occurs, due to poor
reception, you can switch off NICAM setting of the
program.
recording
pressing REC (z).
Each subsequent press
(z)
once.
can
Time
be extended
anytime by
increases the
recording
Caution
unplugged (or there is a power failure)
recording, the recording will be lost.
while the recorder is
Recording will start. (The
display window.)
REC indicator
lights
continues until you press STOP
the disc is full.
Recording
To record for
a
fixed
Recording
Press STOP
(x)
to
on
time
within free space.
If the recorder is
Press REC
Recording
time
in
the
4.
time. The
return to the TV
moment.
To Extend the
NICAM, the regular audio is always recorded. If
Timer
stop
Auto,
can
record the NICAM audio. If the broadcast is
or
screen.
Also, remaining time of recording is shown in the
This recorder
3.
the
Checking
Main+Sub
→
on
recorder will
and shut off.
recording
Right
→
displayed
recording, the
length
right.
of
time,
see
(x)
Instant
Playing
You
can
continuing
1.
2.
are
recording
the
beginning
while
recording.
RAM
of the title while
to record it.
Press PLAY
Start
stop recording.
while you
play from
start
(N)
of the title you are recording.
Press STOP (x) to return to the current
play
recording
screen.
To Pause the
1.
Press PAUSE/STEP
2.
When you want to continue
PAUSE/STEP (X).
To record
watching
or
Recording
(X)
1.
to pause
recording.
recording, press
TV program while
another
Press TV/DVD to select the TV mode
2.
recording. The TV indicator appears.
Using the TV, select the channel to be viewed.
during
recording.
PIP(Picture-In-Picture) window appears on the
screen. What is currently being recorded appears
as a PIP and you will hear the playback audio.
You can change the main and sub picture by
pressing TIMESHIFT.
Press STOP (x) to return to the current recording
The
one
1.
Press TIMESHIFT while
2.
screen.
Notes:
Play
cannot be started until at least 30 seconds
after
recording
starts.
This function is not available
34
during
timer
recording.
Timer
4.
Recording
This recorder
can be programmed to record up to 16
programs within a period of 1 month. For unattended
recording, the timer needs to know the channels to be
recorded,
the
and
starting
ending
b / B
(left/right) move the cursor left/right
(up/down) change the setting at the
current cursor position
Press RETURN (O) to return to the [Timer
Record] list.
Note:
1.
Press HOME and select
2.
Press v / V to select
5.
Press v / V to select
[Timer Record]
menu
the
[Timer Record]
list
[Rec. OK] on the [Timer Record] list
recording is programmed
indicates that the timer
correctly.
6.
7.
will appear.
Press RETURN
(O)
to exit the
[Timer Record]
list.
ENTER.
The
programming,
will appear.
[Check] field's
then
then press
[New] option
ENTER, the program will be memorized by
To check the
press ENTER.
The [Timer Record] list will appear.
3.
Press
--
the recorder.
[TV] option.
[Timer Record] option
--
v / V
time.
If you use a completely blank disc for timer recording,
you must format the disc before starting timer
recording. (Refer to "Initialize" on page 21.)
Enter the necessary information for your timer
recording(s).
Make
that you load a recordable disc for DVD
and press POWER to switch your unit to
sure
recording
Standby.
Notes:
The timer indicator
lights in the display window
standby with the timer
displayed while the [Power Save
when the recorder is in
active.
[PR]
one
(You
Choose
memorized program number, or
of the external inputs from which to record.
cannot select DV
[Date]
or
a
Choose
desired
a
Mode]
(Nothing
ON.)
is
is
You must press POWER to
stop the timer recording.
input.)
Recording
date up to 1 month in advance
repeat (Monday
~
Friday,
or
Every
Sun~Sat).
[Start Time]
[End Time]
Set the start time.
Set the end time.
Choose
[Mode]
or AT).
AT (Auto)
a
record mode
(XP, SP, LP, EP,
mode determines how much disc time
is available and switches record
necessary, to
mode, if
complete recording
the program.
Note:
When you set the PDC
is not available.
option
to
On, AT mode
[PDC] The PDC system automatically adjusts
recording time so that even if a program is
not running to schedule, you won't miss it. For
PDC to work properly, you must input the
the
correct announced time and date of the
program you want to record.
Note that PDC may not work with every station.
Notes:
Stations that
use
PDC
typically include PDC
guide pages.
pages when setting a
information in the teletext TV
Please refer to these
timer
recording.
using PDC, there may be instances
where the beginning of the program is not
When
recorded.
35
3.
Timer
Recording with
VIDEO Plus+ System
This
You
can change the information as required using
b/B/v/V(Mode,etc.)
Refer to "Timer Recording" on previous page.
system makes programming timer recordings
simple. Most TV guides publish VIDEO Plus+
programming numbers with their program details.If
you want to make a timer recording of a program, you
just input the corresponding VIDEO Plus+
programming number. The date, start, stop and
channel settings are made automatically. All you have
to do is tell the recorder the recording mode, and
whether it's a once-only recording, or a regular
recording.
Up to 16 timer programs can be stored in the
very
4.
Press
ENTER, the program will be memorized by
the recorder.
To check the
programming,
will appear.
Check field's "Rec. OK"
indicates that the timer
recorder.
on
the Timer Record List
the Timer Record List
recording
is
programmed
correctly.
VIDEO Plus+ and PlusCode
trademarks of Gemstar
The VIDEO Plus+
system is manufactured under
license from Gemstar
1.
are registered
Development Corporation.
Development Corporation.
Press VIDEO Plus+ button.
The VIDEO Plus+
menu
will appear.
Press VIDEO Plus+ button
[Number]
again
to exit the
Enter the VIDEO Plus+
menu.
programming
number.
2.
Use the number buttons then press ENTER to
programming number.
enter the VIDEO Plus+
To check the
menu
programming,
the Timer Record
will appear.
If you make a mistake before pressing ENTER,
press CLEAR repeatedly to delete password
numbers one by one then correct it.
36
5.
Press RETURN
(O)
to exit the Timer Record
menu.
6.
Make
that you load a recordable disc for DVD
and press POWER to switch your unit to
sure
recording
Standby.
Checking
Timer
If two
Recording
or more
timer programs
Details
The earlier program takes
When the earlier program
Programming
program starts.
If two programs
is turned
can
be checked whenever the recorder
on.
1.
Press HOME and select
2.
Press v / V to select
a
[TV] option.
[Timer Record] option
timer
finishes, the later
set to start at
are
exactly
the
same
time, the program entered first takes priority.
then
press ENTER.
The [Timer Record] list will appear.
Use v / V to select
overlap:
priority.
If the disc is damaged,
complete successfully.
the
Check field shows "Rec.
may not
recording
In this
case even
OK", it may
though
the
not be.
recording.
from
Recording
Input
Press ENTER to edit the selected program.
Timer Record menu appears.
Press CLEAR to delete the selected program
from the Timer Record List.
Recording
You
a
can
from External
record from
camcorder
or
Make
component, such
as
to any of the
inputs.
that the
sure
Components
external
an
VCR, connected
recorder's external
1.
External
an
from is connected
component you
properly
want to record
to the recorder. See
page 13-14.
2.
Press AV/INPUT
input
repeatedly
to select the external
to record from.
Tuner: Built-in tuner
AV1: EURO AV1 AUDIO VIDEO mounted
back
Canceling
a
Timer
Recording
AV2: EURO A/V2 DECODER mounted
can clear a timer setting anytime before the
recording actually starts.
Usev/Vtoselectaprogramyouwanttoeraseon
erase
AV3: AV IN 3 mounted
After
a
Timer
a
timer
Recording
recording
has
in
IN)
the
started, you
can
Timer
Select the
pressing
EP)
still
4.
the timer is set, the recorder will not
no
Power is turned
set to
[ON]
5.
in the
Setup
on.
There
are already 99 titles (DVD-RW, DVD-R,
DVD-RAM), 49 titles (DVD+R, DVD+RW) recorded
on
as necessary by
repeatedly. (XP, SP, LP,
REC indicator
lights
continues until you press STOP
To record for
disc loaded.
[Disc Protect] option is
menu. (see page 22).
mode
or
in
(x)
the disc is full.
Timer
A non-recordable disc is loaded.
recording
REC MODE
Recording
record when:
There is
panel
(L/R), S-VIDEO
on
(z) once.
Recording will start. (The
the display window.)
Recording Troubleshooting
though
back
Press REC
or
Even
back
(VIDEO, AUDIO
front panel
mounted on front panel
mounted
DV: DV IN
Progress
cancel the program.
Press POWER.
on
AV4: AV IN 4
3.
Stopping
on
panel
You
the Timer Recorder List. If you want to
program, press CLEAR.
Recording
on
panel
a
fixed
Recording"
Press STOP
(x)
to
on
length
of
time,
see
"Instant
page 34.
stop recording.
Note:
If your source is copy-protected using CopyGuard,
you will not be able to record it using this recorder.
See Copyright on page 33 for more details.
the disc.
You cannot enter
a
timer program when:
A
recording is already underway.
The time you're trying to set has already passed.
There are already 16 timer programs set.
37
from DV
Recording
Before DV
You
can
recorder
1.
Input
dubbing
connect
2.
DV-equipped
single DV cable
a
a
You cannot connect
at
camcorder to this
more
than
one
DV camcorder
16-bit/48kHz,
or
You
can
record from
the DV IN
Using
jack
on
a
Find the
place on the
recording
page
to
control both the
input
for
using
5.
the
Press REC
using
jack.
You cannot record date and time information from
DV cassette.
to start
recording.
during recording.
on screen
for
a
while
Troubleshooting
If you cannot get a picture and/or audio
DV IN jack, check the bullet points:
sure
Depending
If you connect a second recorder using a DV cable,
you cannot control the second DVD from this one.
You cannot control this unit remotely from a
to the DV IN
once
is
the DV cable is
through
the
properly connected.
equipment then
off the connected
on.
the audio
input.
Note:
this
recorder's remote.
component connected
from
mode, the final frame of the recording
Try switching
must be DVC-SD format.
Some camcorders cannot be controlled
38
(z)
Try switching
signal
point
automatically stopped if the
recorder detects no signal.
You can pause or stop the recording by
pressing PAUSE/STEP (X) or STOP (x).
switch back
source
tape that you
STOP, PLAY and PAUSE functions.
Recording
Make
20).
Tips:
The
camcorder
to start from.
may remain displayed
after recording stops.
digital camcorder connected
panel of this recorder.
that the audio
more
on your camcorder, you can use this
recorder's remote to control the camcorder
remote control
the front
recording, make sure
jack is set up (see
page 20 for
You cannot control the camcorder from this
camcorder and this recorder.
Before
in
Depending
Digital Camcorder
the DV IN
Audio]
See "DV
For best results, pause playback at the
which you want to record.
can
can
Rec
repeatedly to select the DV input.
display window and on the TV
want to the
twin stereo tracks of 12-
the recorder's remote, you
on
[DV
menu.
screen.
4.
In Video
a
Setup
Audio"
Press AV/INPUT
tape, or if the power fails in
component, or the DV cable becomes
from
(overdubbed audio).
is set from the
Recording
disconnected.
Recording
Input
you require.
(original audio)
as
information.
unrecorded section of
source
is
DV appears in the
only record one stereo
audio track. Set [DV Rec Audio] option to [Audio 1]
or [Audio 2] as required (see page 20).
Audio input to the DV IN jack should be 32 or
48kHz (not 44.1kHz).
Picture disturbance on the recording may occur if
the source component pauses playback or plays an
the
input
choose between Audio 1
sub-menu of the
3.
equipment connected via the DV IN jack (including
two recorders).
It may not always be possible to control the
connected camcorder via the DV IN jack.
Digital camcorders can usually record audio as
bit/32kHz. This recorder
can
DV
You cannot control this recorder from external
stereo
your digital camcorder is connected to
DV IN jack. See page 14.
panel
and Audio 2
for
time to this recorder.
a
sure
Check that the DV audio
You
input and output
of audio, video, data and control signals.
This recorder is only compatible with DV-format
(DVC-SD, DV25) camcorders. Digital satellite tuners
and Digital VHS video recorders are not compatible.
using
Make
the front
a
on
the connected
be able to control it
with this recorder.
using
camcorder, you may not
the remote control supplied
12
Editing
Title List and
Chapter
34
56
List Menu
Overview
Using the Title List menu you can edit video content.
editing features available in the Title List menu
depend on whether you are editing video on DVD,
and whether you're editing Original content, or a
Playlist.
The
There
You
are
can
two ways to edit VR mode DVD-RW discs.
edit the Original content of the disc,
directly
you can create and edit a Playlist. The Playlist
doesn't actually change any of the content on the
disc, but just controls how the content is played back.
or
1.
Press MENU/LIST to
Playback
You
should be
also
can
select
display the Title List menu.
stopped when you do this.
access
[Movie] option
it
using
1.
HOME menu,
then select
[DISC] option
and press ENTER.
When
selecting titles, use the v / V buttons to
display the previous/next page if there are more
than six titles.
If you are editing a VR mode disc, press
MENU/LIST to switch between Original and
Playlist
menu.
On the left side of the
The main
part of the
screen are
screen
the
menu
options.
shows thumbnails of the
titles
(or chapter) on the DVD. You can change these
using the THUMBNAIL button---see
Changing Title Thumbnails on page 40.
thumbnails
Press DISPLAY to
title
on
display
the Title List
Menu
options: To display menu option, select a
chapter then press ENTER. The options
displayed differ depending on the disc type.
[Combine] Combines two chapters into one
(page 44).
[Delete] Deletes the title or chapter. (page 42)
[Delete Part] Deletes a part of the Title (page
42).
[Divide] Divides a title into two (page 44).
[Full Play] Starts playback of the selected title
including the hidden chapters.
[Hide (Show)] Hides (or Shows) the selected title
or chapter. (page 45)
[Move] Moves a chapter on the Chapter
List-Playlist menu to a position on the menu.
(page 45)
[Play] Start playback of the selected title or
chapter. The hidden titles and chapters on the
DVD+R/RW cannot be play back.
[Playlist Add] Adds the title or chapter to the
Playlist. (page 41)
[Protect] Protects accidental recording, editing or
deleting of the title. (page 45)
[Title Name] Edits the title name. (page 43)
[Search]
[Chapter]; Displays Chapter List of the Title.
-[Time]; Search time for you want start point of
the title. (page 41)
[Title] Displays Title List of the chapter.
title
the information of selected
menu.
After
selecting a title or chapter on the Title List or
Chapter List menu, then press ENTER. The menu
options appears on the left side of the menu. Use
v / V to select a option then press ENTER to confirm
your selection.
or
Edit ng
-
2.
To exit the Title List menu, press RETURN
(O)
repeatedly.
2.
Indicates the disc name, record
elapsed time progress bar.
mode, free space,
and
selected title.
3.
Currently
4.
Thumbnail
5.
Shows the selected title number and total number
of titles.
6.
Shows the title name, recorded
date, and
recording length.
39
VR Mode:
Original
and
Adding Chapter
Playlist
Markers
Editing
-RW VR
Titles, Chapters and Parts
Titles in the disc's
You
content contain
original
can
chapter
one or
chapters. When you insert a disc's title into the
Playlist, all the chapters within that title also appear. In
other words, chapters in the Playlist behave exactly as
chapters on a DVD-Video disc do. Parts are sections
of Original or Playlist titles. From the Original and
Playlist menu you can add or delete parts. Adding a
chapter or title to the Playlist creates a new title made
up of a section (ie., chapter) of an Original title.
Deleting a part removes part of a title from the
Original or Playlist menu.
RAM
create
+RW
chapters
+R
within
marks at the desired
a
title
by inserting
points.
more
Caution
When
editing using
functions, the
the
Note:
Chapter markers are inserted at regular intervals
automatically. You can change this interval from the
Initial Setup menu (see "Auto Chapter" on page 20).
During recording
want to start
A
pause between edits. This is not
-RW VR
a
editing
tape?
DVD like
a
editing
a
video
a
No. When you edit a video tape you need one video
deck to play the original tape and another to record
the edits. With
DVD, you edit by making
'Playlist'
what to play and when to play it. On playback, the
Recorder plays the disc according to the Playlist.
About word
-RW VR
'Original'
and
a
of
'Playlist'
the edited version.
Playlist:
40
content refers to what's
actually
recorded
the disc.
disc
---
Title Thumbnails
content refers to the edited version of the
how the
Original
content is to be
played.
RAM
+RW
+R
Press THUMBNAIL to make the
picture
the
The still
Original
is
from the
from within
one
picture
Playlist
or
currently displayed
that appears in the Title List menu.
that you choose appears in both the
menu.
Tip:
change the thumbnail picture of the title
Chapter List menu. Select a chapter on the
Chapter List menu then press THUMBNAIL. The
thumbnail picture of the title that includes the chapter
is changed.
on
Throughout this manual, you will often see the words
Original and Playlist to refer to the actual content and
on
screen.
title.
You
RAM
Original:
the TV
Each title displayed in the Title List menu
represented by a thumbnail picture taken
start of that title or chapter.
If you prefer, select a different still picture
malfunction.
Is
on
you
start and end frames may not be
exactly as set in the start and end point display.
During Playlist playback, you may notice a
momentary
playing back, at the point
chapter, press CHP ADD.
marker icon appears
chapter
Changing
Delete, Add and Move
or
a new
can
the
also
Making
-RW VR
a
New
Adding Additional Title/Chapters
RAM
to the Playlist -RW
Playlist
RAM
VR
Use this function to add
You
the
an Original title or chapter to
Playlist. When you do this, the whole title is put
into the Playlist (you can delete bits you don't need
later
see Deleting an Original or Playlist
title/chapter on page 42).
Playlist
1.
can
add
title
Choose
menu or
Playlist,
if you add more chapter markers to the Original
these are not automatically copied over into the
Playlist
You
can
add up to 999
only
title/chapter
title
or
then press ENTER.
menu
options
on
appears
the left side of the
screen.
later,
chapters to one disc If you
chapter of a title, use the Adding
Playlist on this page.
.
a
title or chapter on the Title List-Original
Chapter List-Original menu to put into the
then press ENTER.
menu
options
appears
on
the left side of the
2.
menu.
2.
a
a
menu or
Playlist,
a
to the
Choose
The
to
title.
want to add
1.
The
Original title or chapter to add
if it is already registered.
chapter on the Title List-Original
Chapter List-Original menu to put into the
a
---
The title appears in the Playlist complete with the
chapter markers that appear in the Original. However,
an
even
Use v / V to select
options
Use v / V to select
[Playlist Add] option
then press
ENTER.
3.
Choose
[Playlist Add]
from
menu
then press ENTER.
a
registered
Title
List-Playlist
to insert
a
title
that is
or
already
chapter, then
press
Edit ng
ENTER.
4.
Repeat steps 1-3
the Playlist.
to add additional title
or
chapter
on
You
can
view the added
List-Playlist
3.
Select
The
chapters
on
the
Chapter
menu.
then press ENTER.
title appears in the updated Playlist. All
of the title are added to the Playlist.
[New Playlist]
new
chapters
5.
Press RETURN
back to the Title
(O) to exit,
List-Original
or
MENU/LIST to go
menu.
41
Deleting an Original
Title/Chapter
or
When you
from the
erase a
title
or
chapter
Playlist
You
menu, you only remove it from the Playlist;
title/chapter remains in the Original menu.
If you choose to delete
a
title
or
Deleting
chapter
Playlist
can
a
delete
a
Part
-RW VR
part which you do
RAM
not want in the
title.
the
1.
Useb/B/v/Vtochooseatitleyouwantto
delete
from the
The
Original (title/chapter) menu, the title or chapter is
actually deleted from the disc and the remaining time
available for recording increases. Titles/chapters
deleted from the Original are also removed from the
Playlist.
2.
on
the Title List
options
appears
then press ENTER.
the left side of the menu.
menu
on
Select
[Delete Part] option then press ENTER.
Edit (Delete Part) menu appears on the TV screen.
[Start Point] icon is highlighted.
Note:
It may not be possible to delete
than 5 seconds long.
1.
chapters
that
are
less
Useb/B/v/Vtochooseachapterortitleyou
on the Title List or Chapter List
want to delete
menu
The
then press ENTER.
menu
options
appears
on
the left side of the
3.
Select
2.
[Delete] option
from the
Starts
and
playback
use
slow-motion to find the
screen.
options
on
4.
the
Press ENTER at the
pause step, search and
starting point.
starting point
of the section
you want to delete.
'End Point' icon is highlighted.
menu.
The
5.
6.
part is indicated
Use pause
the ending
step,
on
the
Progress
Bar.
search and slow-motion to find
point.
Press ENTER at the
ending point
of the section
you want to delete.
You
can
select
7.
The confirm message for
deleting
will appear.
Use b / B to select
[Yes] then press ENTER.
chapter or title is deleted.
After pressing ENTER, the new, updated menu
displayed.
4.
If you finish to
ENTER.
List
The selected
5.
Repeat steps
1
-
Press RETURN
4 to continue to delete from the
(O) repeatedly
to exit the
menu.
Notes:
When DVD+RW
is
changed
If
more
titles
recording,
name
to 'Deleted Title'.
than two titles
are
the deleted title's
are
combined into
repeatedly deleted,
the
one.
When you are deleting a title or chapter, only the
last one on DVD+RW increases remaining recording
time.
42
use
v / V to
edit, select [Done] icon then press
menu
appears.
is
menu.
6.
point,
icon then press ENTER.
The confirm message for deleting will appear.
Use b / B to select [Yes] then press ENTER.
The selected part is deleted from the title and Title
Press ENTER to confirm.
3.
cancel the selected
[Cancel]
Note:
It may not be possible to delete
than 3 seconds long.
parts that
are
less
Naming
You
can
Time Search
Title
Playlist
titles
be up to 32 characters
and
long.
Original
can name
Names
1.
a
Choose the title you want to
menu, then press ENTER.
The
options
menu
appears
independently.
-RW VR
You
1.
Use v/V to select
[Title Name] option
Keyboard
3.
point
+RW
-R
+R
of the title.
then press
Useb/B/v/VtochooseatitleontheTitleList
The
2.
then press ENTER.
appears on the left side of the
options
Select
[Time] option
[Search]
ENTER.
menu
select start
menu
the left side of the
menu.
2.
RAM
the Title List
name on
on
can
-RW Video
menu
menu.
then press ENTER.
appears
on
the TV
screen.
appears.
Enteranameforthetitle.Useb/B/v/Vto
select
a
character then press ENTER to confirm
your selection.
Use MENU/LIST button to
change keyboard
Current
type.
picture
OK: Select to finish.
Cancel: Cancels all entered characters.
cursor
Inserts
End time
space at the cursor position.
Delete: Deletes the previous character at the
Space:
a
position.
b / B: Moves
to left
or
right.
Selected
Tip:
Remote control buttons for
PLAY
X
(N):
Inserts
a
entering
space at the
(PAUSE/STEP): Deletes
cursor position.
a name
3.
position.
cursor
the after character at
(STOP),
character at the
cursor
. / >: Moves
Numbers
(0-9):
to left
or
point you want to start.
increase 1 minute step.
If you press and hold b / B then the
4.
previous
position.
cursor
point
5 minute
CLEAR: Deletes the
point
Use b / B to find the
The
the
x
Selected time
Start time
cursor
point
Edit ng
increase
step.
Press ENTER to start selected
point.
right.
Enters the
character at the
cursor
corresponding
position.
4.
Choose OK then press ENTER to fix the
and return to the previous menu screen.
5.
Press RETURN
(O) repeatedly
name
to exit the
menu.
Notes:
Names
can be up to 32 characters long.
For discs formatted on a different recorder, you will
see only a limited character set.
When
recording
on
discs, the entered
player only
DVD-R, DVD+R
name
is
displayed
or
DVD+RW
on
the DVD
after finalization.
43
Divide One Titles Into Two
One
+RW
Use this command to
1.
a
title up into two
On the Title List menu, select
divide then press ENTER.
The
2.
split
menu
options
appears
on
a
Two
Combining
new
titles.
title you want to
the left side of the
+RW
+R
Original chapters
into
Into
RAM
Use this function to combine two
adjacent Playlist
or
one.
Note:
This function is not available if there is
screen.
chapter
Select
1.
[Divide] option.
-RW VR
Chapters
only
one
within the title.
On the
chapter
Chapter
List menu, select the second
chapters you want to combine
of the two
then press ENTER
The menu options appears
on
the left side of the
screen.
2.
Use v / V to select
[Combine] option.
The combine indicator appears between the two
chapters you want to combine.
3.
Press ENTER.
Edit
(Divide)
highlighted.
Current
menu
appears.
[Divide] option
is
picture
3.
The first title's
thumbnail
The second title's
thumbnail
4.
Use
play, pause step, search and slow-motion
point you want to divide the title.
to
find the
5.
Select
[Divide] option
then press ENTER at the
point.
To reset the
point, select [Cancel] option
Repeat from step 3.
then
press ENTER.
6.
Choose
[Done] option
dividing point.
then press ENTER to fix the
The title is divided into two
new
titles. It take up to
4 minutes to divide.
Note:
You cannot select
44
dividing point
less than 3 seconds.
Press ENTER.
Moving
-RW VR
a
Playlist Chapter
Tip
RAM
Use this function to re-arrange the playing order of
Playlist chapters on the Title List-Playlist menu.
If you select a hidden chapter or title on the Title List
or Chapter List menu, you can 'show' it by choosing
[Show] option on the menu. After doing that, you are
able to
see
the
Protect
Note:
This function is not available if there is
only
a
chapter
Title
+RW
+R
-RW VR
Use this function to
Select
a
chapter
the
on
Chapter List-Playlist
menu.
Press ENTER.
2.
The
menu
on
appears
the left side of the
menu.
[Move] option
from
Playlist
then press ENTER.
options
4.
Hide
a
You
skip playing chapters
Chapter/Title
or
+RW
+R
titles without
deleting
from the disc.
1.
Use vVbBto choose
to hide
protect against accidental
or
of the title.
deleting
Press MENU/LIST to
display
Use vVbBto choose
on
the Title List
a
or
Options
3.
Useb/B/v/Vtochoosetheplaceyouwantto
move the chapter to then press ENTER.
After pressing ENTER, the updated menu is
displayed.
can
2.
RAM
a
the Title List
menu.
title you want to
protect
then press ENTER.
Use v / V to select
3.
recording, editing
1.
options
title.
one
chapter.
1.
or
chapter
Chapter
4.
Select
appear
[Protect]
on
the left side of the
from the
screen.
options.
Press ENTER to confirm.
The lock mark will appears
on
the title's thumbnail.
Tip
If you select a title that has already been protected on
the Title List menu, you can 'unprotect' it by choosing
[Protect] option from the Title List menu options. After
doing that,
you
can
edit and delete the title.
Edit ng
or title you want
List menu, then
press ENTER.
Options
2.
Select
appear
the left side of the
screen.
[Hide] option.
Example:
3.
on
Title List
(DVD+RW)
Press ENTER to confirm.
The
chapter's
or
title's thumbnail will dim.
45
2.
Reference
To overwrite
a new
video
You
can remove
STOP
+RW
recording
play
will appear
menu
or
stop mode.
as
shown below.
Tip
Additional Information
Overwriting Recording
Press TITLE in
Title List
on a
the Title List
menu
by pressing
(x).
previously
recorded
title, follow these steps. This feature is not
available for DVD+Rs, that always record at the end
of the Disc.
Select
1.
input
you want to record
source
(TV
channel, AV1-4, DV).
Press MENU/LIST to
2.
the Title List
display
menu.
To
3.
play
back
a
press ENTER
title, select the title you
or
PLAY
want then
(N).
Playing Your Recordings on Other
Players (Finalizing a Disc)
Most
regular
DVD
recorded in Video
players
play
can
Use vVbBto choose
3.
a
title you want to
Check the manual that
Press REC
4.
Overwrite
to start overwrite
(z)
recording
recording.
point
starts from the start
new
(x)
to
stop the overwrite recording.
title is created and
updated
menu
is
displayed.
Notes:
If the overwrite is
longer
of the current
a
protected title.
recording
than the
title, the
overwriting stops
at the
protected,
starting point of
the
the
title.
If the selected title's
seconds, the
recording length
Title List
can
1.
46
to
play.
'fixes' the
recordings and editings in place
be played on a regular DVD
computer equipped with a suitable DVD-
that the disc
so
player
or
can
ROM drive.
Finalizing a Video mode disc creates a menu screen
navigating the disc. The menu can be accessed by
pressing MENU/LIST or TITLE.
player
that is
on
displayed on the
capable of playing DVD+RW
menu
DVD+R discs.
Insert DVD+R
To finalize
disc, refer
to "Finalize"
on
page 21.
Notes:
Unfinalized DVD+RW is
DVD+RW disc recorded
playable
on
regular
DVD
players.
The edited contents of
compatible
Any edited
compatible
on
regular
a
DVD+RW disc is
DVD
players only
after
already.
contents of the DVD+R disc
are
not
regular DVD players. (Hide, chapter
combine, added chapter mark, etc.)
How long finalization takes depends on the type of
on
disc, how much is recorded
number of titles
on
DVD+R DL disc
can
finalize.
or
a
finalization.
+R
view the Title List
other DVD
or
displayed
or Players
menu
other DVD Recorders
+RW
is less than 10
next title is overwritten. But if the next
protected, overwriting stops.
Viewing
You
not.
player
next title is
overwritten. But if next title is
title is
with the other
play
or
for
This function is not available for
length
also
of
Finalizing
Press STOP
The
came
or
can
mode, finalized
check what formats of discs it will
the title.
5.
players
DVD-RW discs recorded in VR
overwrite.
finalized discs
mode, finalized DVD+R
DVD+RWs. A small number of
DVD
on
the
disc, and the
the disc.
take up to 30 minutes to
Language Codes
Use this list to
Disc
input
your desired
language
for the
following
initial
settings:
Audio, Disc Subtitle, Disc Menu.
Language
Code
7678
Language
Singhalese
Code
7074
Language
Lingala
Code
6566
Language
Fiji
Code
Abkhazian
Afar
6565
Finnish
7073
Lithuanian
7684
Slovak
8375
Afrikaans
6570
French
7082
Macedonian
7775
Slovenian
8376
Albanian
8381
Frisian
7089
7771
Somali
8379
Ameharic
6577
Galician
7176
7783
Spanish
6983
Arabic
6582
Georgian
7565
Malagasy
Malay
Malayalam
7776
Sudanese
8385
Armenian
7289
German
6869
Maltese
7784
Swahili
8387
Assamese
6583
Greek
6976
Maori
7773
Swedish
8386
Aymara
Azerbaijani
6588
Greenlandic
7576
Marathi
7782
8476
6590
Guarani
7178
Moldavian
7779
Tagalog
Tajik
Bashkir
6665
Gujarati
7185
Mongolian
7778
Tamil
8465
Basque
Bengali; Bangla
6985
Hausa
7265
Nauru
7865
Tatar
8484
6678
Hebrew
7387
7869
Telugu
8469
Bhutani
6890
Hindi
7273
7879
Thai
8472
Bihari
6672
Hungarian
7285
7982
Tibetan
6679
Breton
6682
Icelandic
7383
Nepali
Norwegian
Oriya
Panjabi
8065
8473
Bulgarian
6671
Indonesian
7378
Pashto, Pushto
8083
Tigrinya
Tonga
Burmese
7789
Interlingua
7365
Persian
7065
Turkish
8482
Byelorussian
6669
Irish
7165
Polish
8076
Turkmen
8475
Cambodian
7577
Italian
7384
Portuguese
8084
Twi
8487
Catalan
6765
Japanese
7465
Quechua
8185
Ukrainian
8575
Chinese
9072
Javanese
7487
Rhaeto-Romance
8277
Urdu
8582
Corsican
6779
Kannada
7578
Rumanian
8279
Uzbek
8590
Croatian
7282
Kashmiri
7583
Russian
8285
Vietnamese
8673
Czech
6783
Kazakh
7575
Samoan
8377
Volapuk
8679
Danish
6865
Kirghiz
7589
Sanskrit
8365
Welsh
6789
Dutch
7876
Korean
7579
Scots Gaelic
7168
Wolof
8779
English
Esperanto
6978
Kurdish
7585
Serbian
8382
Xhosa
8872
6979
Laothian
7679
Serbo-Croatian
8372
Yiddish
7473
Estonian
6984
Latin
7665
Shona
8378
Yoruba
8979
Faroese
7079
Latvian, Lettish
7686
Sindhi
8368
Zulu
9085
8373
8471
8479
Area Codes
Choose
an area
Area
code from this list.
Code
AF
Area
Code
Area
Code
Area
Code
ET
Malaysia
MY
Saudi Arabia
SA
FJ
Maldives
MV
SN
Finland
FI
Mexico
MX
France
FR
Monaco
MC
Senegal
Singapore
Slovak Republic
BE
Germany
DE
Mongolia
MN
Slovenia
SI
Bhutan
BT
Great Britain
GB
Morocco
MA
South Africa
ZA
Bolivia
BO
Greece
GR
Nepal
NP
South Korea
KR
Brazil
BR
Greenland
GL
Netherlands
NL
Spain
ES
Cambodia
KH
Heard and McDonald Islands
HM
Netherlands Antilles
AN
Sri Lanka
LK
Canada
CA
Hungary
HU
New Zealand
NZ
Sweden
SE
Chile
CL
India
IN
Switzerland
CH
CN
Indonesia
ID
Nigeria
Norway
NG
China
NO
Thailand
TH
Colombia
CO
Israel
IL
Oman
OM
CG
Italy
IT
Pakistan
PK
Turkey
Uganda
TR
Congo
Costa Rica
CR
Jamaica
JM
Panama
PA
Ukraine
UA
Croatia
HR
JP
United States
US
KE
Paraguay
Philippines
PY
CZ
Japan
Kenya
PH
Uruguay
UY
Denmark
DK
Kuwait
KW
Poland
PL
Uzbekistan
UZ
Ecuador
EC
LY
Portugal
PT
Vietnam
VN
Egypt
EG
Libya
Luxembourg
LU
Romania
RO
Zimbabwe
ZW
El Salvador
SV
Russian Federation
RU
Afghanistan
Argentina
AR
Ethiopia
Fiji
Australia
AU
Austria
AT
Belgium
Czech
Republic
SG
SK
UG
47
Controlling Your TV with the
Supplied Remote Control
You
can
control the sound
level, input
power switch of your LG TV with the
You
can
control your TV
using
You
source, and
supplied
other TVs with the remote
Controlling
remote.
can
control the sound
level, input
source, and
power switch of non-LG TVs as well. If your TV is
listed in the table below, set the appropriate
manufacturer code.
the buttons below.
1.
While
holding down TV POWER button, press the
number buttons to select the manufacturer code
for your TV
2.
(see
the table
below).
Release TV POWER button.
Code numbers of controllable TVs
If
more
them
than
one
at
one
code number is
listed, try entering
time until you find the
a
one
that works
with your TV.
TV Control
Buttons
Manufacturer
Code Number
LG / GoldStar
1
Zenith
1,3,4
Samsung
6,7
(Default),
Sony
8,9
Hitachi
4
2
Notes:
Depending
function
on
on
your
the TV,
TV,
some or
even
after
all buttons may not
the correct
entering
manufacturer code.
By pressing
You
POWER
Turn the TV
AV/INPUT
Switch the TV's
can
on or
If you enter a new code number, the code number
entered will be erased.
previously
off.
input
source
between the TV and other
input
sources.
48
PR/CH +/--
Scans up or down through
memorized channels.
VOL +/--
Adjust
MUTE
Temporarily
press again
to restore.
default
again.
the volume of the TV.
turns TV sound
When you replace the batteries of the remote, the
code number you have set may be reset to the
OFF,
setting.
Set the
appropriate
code number
Troubleshooting
Check the
following guide
for the
possible
cause
of
a
problem
before
contacting
Cause
Symptom
Solution
The power cord is disconnected.
No power.
Plug
the power cord into the wall
outlet
No
service.
picture.
securely.
TV/DVD mode for the recorder is set
Press TV/DVD
to TV.
repeatedly to choose DVD mode. TV
indicator disappears in the display
on
the remote control
window.
The TV is not set to receive recorder
Select the
signal output.
on
The video cable is not connected
Connect the video cable
the TV
appropriate video input
the picture from the
mode
so
recorder appears
the TV
on
screen.
securely.
securely.
No sound.
The connected TV power is turned off.
Turn
The
Select the correct
connected with the
equipment
audio cable is not set to receive
recorder
signal output.
The audio cables
not connected
are
the TV.
on
input mode on the
you can listen to the
sound from the recorder.
audio receiver
so
Connect the audio cable
securely.
securely.
The
playback picture
is
The power of the equipment connected
with the audio cable is turned off.
Turn
The audio
Replace
connecting
The disc is
cord is
damaged.
the
on
equipment
connected
with the audio cable.
it with
new one.
Clean the disc.
dirty.
poor.
The recorder does not
start
No disc is inserted.
Insert
disc.
a
(Check that the disc
display window is lit.)
indicator in the
playback.
An
unplayable
disc is inserted.
Insert
a
playable
disc.
(Check the
disc
type, color system, and regional code.)
The disc is
placed upside
down.
Place the disc with the
side
playback
down.
The disc is not
placed
within the
guide.
The
picture from
input is
the
dirty.
The
level is set.
Rating
The video
Cancel the
the
from the external
signal
distorted
Some channels
are
Those channels
are
recorder.
The
picture or sound of
broadcasting channel is
weak or missing.
Aerial
Camcorder
Camcorder is off.
image
is not
image
via
cables
not stored in the
are
loose.
Camcorder
input
or
rating
tray
guide.
Rating
function
or
change
level.
Connect the component
your TV.
Restore channels. See
directly
to
"Program
Edit"
page 17.
Tighten
connections
Turn camcorder
on
or
replace
and
cable.
operate
properly.
shown.
A/V
the disc
You cannot connect via this recorder.
on
skipped over when
using PR/CH (+/-).
or
on
inside the
Clean the disc.
The disc is
component is copy-protected.
external
Place the disc
correctly
DV IN to
The recorder's
source
is incorrect.
Use AV/INPUT to select
input
channel
(AV1, AV2, DV, etc.)
recorder is not shown
on
TV
screen.
49
Cause
Symptom
Cannot
The disc
play a disc
using this
recorded
recorder
on
Some
another
Solution
recorded in Video mode.
was
will not
players
play
Finalize the disc.
(page 21)
No solution.
even a
finalized disc recorded in Video mode.
player.
The disc
was
recorded in VR
The other
player must be RW
compatible in order to play it.
mode,
Discs recorded with copy-once material
played on other players.
No solution.
The
Use another disc.
cannot be
Cannot record
not record
or
did
The
source
protected.
When
setting
When
the
protected
recording
possible.
the
on
to record is
trying
recording channel,
on
recording
programs that
is not
are
you
copy
channel is tuned
Timer
blank space
remaining
disc is insufficient.
successfully.
the TV's
to
a
own
the
source.
Select the channel
the recorder's
on
built-in TV tuner.
tuner.
Video mode
You cannot record the
Use
disc,
a
VR mode formatted disc for
copy-once material.
are
copy-once
cannot be recorded.
Clock in recorder is not set to correct
Set clock to correct time. See "Auto
time.
Clock Set"
or
"Manual Clock Set"
on
page 17.
Timer has been
programmed
Reprogram
Recording"
incorrectly.
Timer record indicator
appear after
Stereo Audio Record
and/or
Playback
TV is not
is not
light does
programming timer.
not
Reprogram
page 35.
Timer.
No solution.
Stereo-compatible.
Broadcast program is not in stereo
present.
Timer. See "Timer
on
No solution.
format.
The recorder A/V Out
jacks are
jacks.
Make A/V connections. Stereo is
not
connected to TV A/V In
available
only
via A/V
output from the
recorder.
The recorder Audio/Video Out is not
Select AUX
selected for
input.
viewing
at the TV.
or
A/V
source as
TV
The recorder's TV audio channel is
Set TV audio channel mode to Stereo.
set to
See
mono.
"Changing
TV audio channel"
on
page 34.
The remote control
The remote control is not
does not work
the remote
properly.
sensor
pointed
Point the remote control at the remote
at
of the recorder.
sensor
of the recorder.
The remote control is too far from the
Operate
recorder.
7m.
There is
an
obstacle in the
path
of the
the remote control within
Remove the obstacle.
remote control and the recorder.
The batteries in the remote control
are
Resetting
the recorder
If you observe any of the
The unit is
on or
50
following symptoms...
but the power will not turn
off.
The front
The
plugged in,
Replace
the batteries with
new ones.
exhausted.
panel display is not working.
recorder is not operating normally.
...you
can
reset the recorder as follows:
Press and hold the POWER button for at least five
seconds. This will force the unit to power off then
turn the unit back on.
Unplug
the power
plug it in
and then
cord, wait
again.
at least five
seconds,
Specifications
General
Power
AC
Power
22W
requirements
consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Television
200-240V, 50/60 Hz
430 X 54 X 275
4.1
mm
(w
x
h
x
d)
without foot
kg
5˚C to 35˚C
5 % to 90 %
system
PAL
Recording
format
PAL
I, B/G, I/I, SECAM D/K, K1 color system
Recording
format
DVD Video
Recording
Recordable media
Recordable time
Recording,
DVD-VIDEO
DVD-ReWritable, DVD-Recordable, DVD+ReWritable,
DVD+Recordable, DVD+Recordable (Double Layer), DVD-RAM
DVD
(4.7GB): Approx. 1 hour (XP mode), 2 hours (SP mode),
(LP mode), 6 hours (EP mode)
DVD+R DL (8.5GB): Approx. 2 hour (XP mode),
3 hours 40 minutes (SP mode), 7 hours 10 minutes (LP mode),
11 hours (EP mode)
4 hours
Video
recording format
Sampling frequency
Compression format
Audio recording format
Sampling frequency
Compression format
27MHz
MPEG 2
(VBR support)
48kHz
Dolby Digital
Playback
Frequency
response
Signal-to-noise
ratio
Harmonic distortion
Dynamic
range
DVD
(PCM 48 kHz): 8 Hz to 22 kHz, CD: 8
DVD(PCM96kHz):8Hzto44kHz
More than 100 dB (AUDIO OUT connector)
Less than 0.008% (AUDIO OUT connector)
More than 95 dB (AUDIO OUT connector)
Hz to 20 kHz
Inputs
AERIAL IN
Aerial
input, 75 ohms
Vp-p 75 ohms, sync negative,
VIDEO IN
1.0
AUDIO IN
2.0 Vrms
S-VIDEO IN
DV IN
more
than 47
RCA jack
x
2 / SCART
kohms, RCA jack (L, R)
(Y) 1.0 V (p-p), 75 Ω, sync negative,
(C)0.3V(p-p)75Ω
4 pin (IEEE 1394 standard)
Mini DIN
x
x
2
2 / SCART
4-pin
x
1
1 Vp-p 75 Ω, sync negative, RCA jack x 1 / SCART
(Y) 1.0 V (p-p), 75 Ω, sync negative, Mini DIN 4-pin
(C)0.3V(p-p)75Ω
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
19 pin (HDMI standard, Type A)
x
2
x
1
x
2
Outputs
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
HDMI video/audio
output
(DR198H only)
Audio output (digital audio)
Audio output (optical audio)
Audio output (analog audio)
0.5 V
3 V
2.0
(p-p), 75 Ω, RCA jack x 1
(p-p), Optical connector x 1
Vrms (1 KHz, 0 dB), 600 Ω,
RCA jack
(L, R)
x
1 / SCART
x
2
Accessory:
Scartcable.............................1
Videocable.....................1
Audiocable(L,R)........................1
RFCoaxialCable................1
Remotecontrol..........................1
Batteries.......................2
Design
and
specifications
are
subject
to
change
without notice.
51
human touch
Technology with the
GUARANTEE
LG Electronics U.K. Ltd. will
1.
All
2.
The dealer
provide
the
following
services in order to
faulty components which fail due to defective manufacture
period of 12 months from the original date of purchase.
will be
expedite
replaced
this Guarantee.
free of
charge
for
a
(or his service agent) who sold the product will be reimbursed for any labour provided
repair of this LG equipment, for a period of 12 months from the original date of purchase.
These claims must be made in accordance with the published scale of service charges and
relevant claims procedure.
in the
PLEASE NOTE:
A.
The dealer may restrict the
B.
The dealer is not
guarantee
to the
original purchaser.
to carry out service under
guarantee if unauthorized modifications are
apparatus, or if non standard components are used or if the serial number of the
apparatus is removed, defaced, misused, or altered.
obliged
made to the
C.
Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a
receipted account as evidence of the date of purchase.
D. We
respectfully point
exhausted
E.
Aerial
This
or worn
alignment
in
and
guarantee does
out that your dealer is not
obligated
to
replace
batteries if
they
become
use.
consumer
control
not affect your
adjustments
are
not covered
by
this
guarantee.
statutory rights.
REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE
SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED.
Product
Registration
Card
It is
helpful to complete at least your name, address, phone,
model & serial numbers and return it. This will enable LG to
:
assist you in the future should you lose your receipt, your
units be stolen, or should modifications be necessary.
To obtain information
or
assistance:
Call 0870 873 5454
MODEL NO.*
*
Please
complete
SERIAL NO.*
for your
own
Monday-Friday 9.00am-4.30pm
DATE OF PURCHASE.*
record
In all cases of difficulty consult your LG dealer
from whom the product was purchased
-
LGEUK Website
(
service website
P/NO:3834RD0094K
:
:
www.lge.co.uk
www.lgelectronics.co.uk )
Download PDF

advertising