LG | DH900 | LG DH900 Owner’s Manual

OWNER’S MANUAL
DVD Home Cinema
System
Please read this manual carefully before operating
your set and retain it for future reference.
FOR THE WARRANTY TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL.
DH900 (DH900, SH36SD-S/W)
HT356SD-D0_BGBRLL1_ENG_5763.indd 1
2011-10-10 �� 9:32:27
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
HT356SD-D0_BGBRLL1_ENG_5763.indd 2
2011-10-10 �� 9:32:27
Getting Started
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some
discs. When recording and playing the pictures of
these discs picture noise will appear. This product
incorporates copyright protection technology that
is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection
technology must be authorized by Macrovision, and
is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot use
it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
Disposal of your old appliance
1. W
hen this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/EC.
2. A
ll electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or
the local authorities.
3. T he correct disposal of your
old appliance will help prevent
potential negative consequences
for the environment and human
health.
HT356SD-D0_BGBRLL1_ENG_5763.indd 3
4. F or more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.
1
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive
2004/108/EC, 2006/95/EC, and
2009/125/EC.
Getting Started
Copyrights
3
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands (Tel : +31–(0)36–547–8888)
POWER: This unit operates on a mains supply of
200-240V~, 50/60Hz.
WIRING: This unit is supplied with a BSI 1363
approved 13 amp mains plug, fused at 5 amp.
When replacing the fuse always use a 5 amp BS
1362, BSI or ASTA approved type. Never use this
plug with the fuse cover omitted. To obtain a
replacement fuse cover contact your dealer. If the
type of plug supplied is not suitable for the mains
sockets in your home, then the plug should be
removed and a suitable type fitted. Please refer to
the wiring instructions below:
WIRING: A mains plug removed from the mains
lead of this unit must be destroyed. A mains plug
with bared wires is hazardous if inserted in a
mains socket. Do not connect either wire to the
earth pin, marked with the letter E or with the
earth symbol or coloured green or green and
yellow. If any other plug is fitted, use a 5 amp fuse,
either in the plug, or at the distribution board.
IMPORTANT: The wires in this mains lead are
coloured in accordance with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours
of the wires in the mains lead of this unit may not
correspond with the coloured marking identifying
the terminals in your plug, proceed as follows: The
wire which is coloured blue must be connected
to the terminal which is marked with the letter
N or coloured black. The wire which is coloured
brown must be connected to the terminal which
is marked with the letter L or coloured red.
2011-10-10 �� 9:32:27
4
Table of Contents
Table of Contents
1
Getting Started
2
6
6
6
6
7
7
7
7
7
8
10
10
11
Safety Information
Unique Features
– Portable In
– USB Direct Recording
Accessories
Introduction
– Playable Discs
– About the & Symbol Display
– Symbol Used in this Manual
– Regional Codes
– Playable file Requirement
Front panel
Rear panel
Remote control
2 Connecting
12
12
12
13
13
14
14
14
14
14
15
15
Connecting the speakers
– Attaching the speakers to the unit
– Positioning the System
Connections to Your TV
– Component Video Connection
– Video Connection
– SCART Connection
Optional Equipment Connection
– AUX IN Connection
– AUDIO IN (P. IN) Connection
– USB Connection
– Antenna Connection
3 System Setting
16
16
16
16
17
18
18
19
4 Operating
20
21
21
21
21
21
21
22
22
22
22
23
23
23
23
23
23
24
24
24
24
24
24
24
24
24
25
25
26
26
26
Basic Operations
Other Operations
– Displaying Disc Information on-screen
– To display the DVD Menu
– To display the DVD Title
– Selecting a subtitle language
– 1.5 times speed playback
– Starting play from selected time
– Last Scene Memory
– Changing the character set to display
DivX® subtitle correctly
– Programmed Playback
– Viewing a PHOTO file
– Viewing photo files as a slide show
– Listening to music during slide show
– Sleep Timer Setting
– Dimmer
– Turn off the sound temporarily
– Screen Saver
– System Select - Optional
– Displaying file information
(ID3 TAG )
Radio Operations
– Listening to the Radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Improving poor FM reception
– Seeing information about a radio
station
Sound adjustment
– Setting the surround mode
Advanced Operations
– Listening to music from your portable
player or external device
– Recording to USB
Adjust the Setup settings
– OSD Initial language settings Optional
– To display and exit the Setup Menu
– LANGUAGE
– DISPLAY
– AUDIO
– LOCK (Parental Control)
– OTHERS
HT356SD-D0_BGBRLL1_ENG_5763.indd 4
2011-10-10 �� 9:32:27
Table of Contents
5
5 Troubleshooting
27
Troubleshooting
6 Appendix
28
28
28
29
30
31
32
Maintenance
– Handling the Unit
– Notes on Discs
Area Code List
Language Code List
Trademarks and Licenses
Specifications
7 Warranty
1
2
3
34 Warranty
4
5
6
HT356SD-D0_BGBRLL1_ENG_5763.indd 5
2011-10-10 �� 9:32:27
6
Getting Started
Unique Features
1
Portable In
Accessories
Please check and identify the supplied accessories.
Getting Started
Listens to music from your portable device.
(MP3, Notebook, etc)
USB Direct Recording
Records music from CD to your USB device.
HT356SD-D0_BGBRLL1_ENG_5763.indd 6
FM Antenna (1)
Remote Control (1)/
Battery (1)
2011-10-10 �� 9:32:28
Getting Started
Introduction
Playable Discs
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and finalized only.
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only. DVD VR format that have been
finalized can not be played in this
unit.
DVD+R: Video mode only.
Supports the double layer disc also.
DVD+RW (8 cm / 12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
Symbol Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
y
Video files contained in the
USB/Disc
u
Audio files contained in the
USB/Disc
i
Photo files
1
Getting Started
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CD-RW/
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc,
or the characteristics of the recording device and
authoring software.
7
,,Note
Indicates special notes and operating features.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or “ALL”.
ost DVD discs have a globe with one or more
yy M
numbers in it clearly visible on the cover. This
number must match your unit’s regional code; or
the disc cannot play.
yy If you try to play a DVD with a different regional
code from your unit, the message “Check
Regional Code” appears on the TV screen.
About the & Symbol Display
“ & ” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that disc.
HT356SD-D0_BGBRLL1_ENG_5763.indd 7
2011-10-10 �� 9:32:28
8
Getting Started
Playable file Requirement
Compatible USB Devices
yy MP3 Player : Flash type MP3 player.
MP3/ WMA music file requirement
1
Getting Started
MP3/ WMA file compatibility with this unit is limited
as follows :
yy S ampling frequency : within 32 kHz to 48 kHz (MP3), within 32 kHz to 48 kHz (WMA)
it rate : within 32 kbps to 320 kbps (MP3), 40
yy B
kbps to 192 kbps (WMA)
yy Support Version : v2, v7, v8, v9
yy Maximum files : Under 650
yy File extensions : “.mp3”/ “.wma”
yy CD-ROM file format : ISO9660/ JOLIET
e recommend that you use Easy-CD Creator,
yy W
which creates an ISO9660 file system.
Photo file requirement
JPEG disc compatibility with this unit is limited as
follows :
yy Max pixel in width : 2 760 x 2 048 pixel
yy Maximum files : Under 650
yy S ome discs may not operate due to a different
recording format or the condition of disc.
yy File extensions: “.jpg”
evices that support USB2.0 or
yy USB Flash Drive : D
USB1.1.
yy T he USB function of this unit does not support
some USB devices.
USB device requirement
evices which require additional program
yy D
installation connected to a computer, are not
supported.
yy Do not extract the USB device while in operation.
yy F or a large capacity USB, it may take longer than
a few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
sing NTFS file system is not supported. (Only
yy U
FAT(16/32) file system is supported.)
yy T his unit is not supported when the total
number of files is 1 000 or more.
yy E xternal HDD, Card readers, Locked devices, or hard type USB devices are not supported.
SB port of the unit cannot be connected to PC.
yy U
The unit can not be used as a storage device.
yy CD-ROM file format : ISO9660/ JOLIET
HT356SD-D0_BGBRLL1_ENG_5763.indd 8
2011-10-10 �� 9:32:28
Getting Started
9
DivX file requirement
DivX file compatibility with this unit is limited as
follows :
vailable resolution: yy A
within 720 x 576 (W x H) pixels.
yy If there is impossible code to express in the
DivX file, it may be displayed as “ _ “ mark on the
display.
Getting Started
yy T he file name of the DivX subtitle should be
entered within 45 characters.
1
yy F rame rate : less than 30 fps.
yy If the video and audio structure of recorded
files is not interleaved, either video or audio is
outputted.
layable DivX file : “.avi”, “.mpg”, “.mpeg”, “.divx”
yy P
layable Subtitle format : SubRip (*.srt/ *.txt),
yy P
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
layable Codec format : “DIVX3.xx”, “DIVX4.xx”,
yy P
“DIVX5.xx”, “MP4V3”, “3IVX”.
layable Audio format : “AC3”, “PCM”, “MP3”, “WMA”.
yy P
yy S ampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
it rate : within 32 to 320 kbps (MP3), 40 to 192
yy B
kbps (WMA)
yy F or Discs formatted in Live file system, you can
not it on this unit.
yy If the name of movie file is different from that of
the subtitle file, during playback of a DivX file,
subtitle may not be display.
yy If you play a DivX file different from the DivXspec,
it may not operate normally.
HT356SD-D0_BGBRLL1_ENG_5763.indd 9
2011-10-10 �� 9:32:28
10
Getting Started
Front panel
1
1
2 3
4
5 6 7
Getting Started
11
a DVD/CD Disc Drawer
10
9
8
h TUNING (-/+)(C/V), Skip/Search
You can search chapter/ track/ file by pressing
and holding C/V.
b Power (1/!)
c Open/Close (B)
i USB port
You can play video, image and sound files by
connecting the USB device.
d Display window
e Play/Pause (d/M), MONO/ ST.
f Stop (Z)
.(Portable) IN port
jP
You can enjoy music from portable device on
your unit.
g Function (F)
Selects the function or input source.
k Volume (VOL.)
Rear panel
1
2
3
4
6
5
7
a Power cord
b Speaker terminal
c ANTENNA connector (FM)
d SCART connector
HT356SD-D0_BGBRLL1_ENG_5763.indd 10
e MONITOR (VIDEO OUT) connector
Connect to a TV with video inputs.
f AUX (L/ R) INPUT connector
g COMPONENT VIDEO (PROGRESSIVE SCAN)
OUTPUT (Y PB PR)
Connect to a TV with Y PB PR inputs.
2011-10-10 �� 9:32:29
Getting Started
11
Remote control
1
VOL (Volume) (+/-) : Adjusts
speaker volume.
OPEN/CLOSE : Opens and closes
the disc Drawer.
LG EQ (9) : Selects a Natural or
Local Specialization equalizer
effect by using LG EQ.
TITLE : If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
• • • • • • b • • • • • •
3
DISPLAY : Accesses On-Screen
Display.
MENU : Accesses the menu on a
DVD disc.
4
SETUP : Accesses or removes
setup menu.
PRESET (WS) : Selects
programme of Radio.
5
TUN. (-/+) : Tunes in the desired
radio station.
W/S/A/D (up/ down/ left/
right): Used to navigate on-screen
displays.
ENTER (b) : Acknowledges menu
selection.
Battery Installation
RETURN (x) : Moves backwards
in the menu or exits the setup
menu.
REC (X) : USB Direct Recording.
• • • • • • c • • • • • •
STOP (Z) : Stops playback or
recording.
Remove the battery cover on the
rear of the Remote Control, and
insert one (size AAA) battery with
4 and 5 matched correctly.
• • • • • • a • • • • • •
FUNCTION : Selects the function
and input source.
SLEEP : Sets the system to turn off
automatically at a specified time.
(Dimmer : The display window will
be darken by half.)
HT356SD-D0_BGBRLL1_ENG_5763.indd 11
EQ$ (EQUALIZER effect) :
Chooses sound impressions.
CLEAR : Removes a track number
on the Program List.
1
Getting Started
2
POWER : Switches the unit ON or
OFF.
SUBTITLE : During playback, press
SUBTITLE repeatedly to select a
desired subtitle language .
0 to 9 numerical buttons :
Selects numbered options in a
menu.
• • • • • • e • • • • • •
TV Control buttons : Controls the
TV. (LG TV only)
-- You can control the sound
level, input source, and power
switching of LG TVs as well.
Hold POWER (TV) and press
PR/CH (+/–) button repeatedly
until the TV turns on or off.
PROG./MEMO. : Accesses or
removes Program menu.
?: This button is not available.
RDS : Radio Data System.
PTY : Views the various displays of
the RDS.
PLAY (d), MO./ST. : Starts
playback. Selects Mono/ Stereo.
PAUSE/STEP (M) : Pauses
playback.
SKIP (C/V) : Goes to next
or previous chapter/ track/ file.
SCAN (c/v) : Searches
backward or forward.
• • • • • • d • • • • • •
REPEAT/RANDOM : Selects a play
mode.(Random, repeat)
MUTE : Mutes the sound.
2011-10-10 �� 9:32:29
12
Connecting
Connecting the
speakers
Attaching the speakers to the
unit
2
Connecting
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
Connect the black stripe of each wire to the
terminals marked - (minus) and the other end to
the terminals marked + (plus).
Speaker connection
Positioning the System
The following illustration shows an example of
positioning the system.
Note that the illustrations in these instructions differ
from the actual unit for explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position ( ).
Speaker Positioning
Front left speaker (L)/ Front right speaker (R):
Place the front speakers to the sides of the
monitor or screen and as flush with the screen
surface as possible.
Center speaker: Place the center speaker above
or below the monitor or screen.
Surround left speaker (L)/ Surround right
speaker (R):
Place these speakers behind your listening
position, facing slightly inwards.
>>Caution
yy Be careful to make sure children not to put
their hands or any objects into the *speaker
duct.
*Speaker duct: A hole for plentiful bass
sound on speaker cabinet (enclosure).
yy The speakers contain magnet parts, so
color irregularity may occur on the TV
screen or PC monitor screen. Please use the
speakers far away from either TV screen or
PC monitor.
Subwoofer: The position of the subwoofer is
not so critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it slightly
toward the center of the room to reduce the wall
reflections.
Unit
B
C
A
G
F
A
A
A
A
D
HT356SD-D0_BGBRLL1_ENG_5763.indd 12
E
A
2011-10-10 �� 9:32:30
Connecting
Connections to Your
TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
,,Note
13
Component Video Connection
Connect the COMPONENT VIDEO (PROGRESSIVE
SCAN) OUTPUT jacks on the unit to the
corresponding input jacks on the TV using Y PB PR
cables.
You can hear the sound through the system’s
speakers.
yy Depending on your TV and other
equipment you wish to connect, there are
various ways you could connect the player.
Use only one of the connections described
in this manual.
2
Connecting
yy Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
>>Caution
yy Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel.
yy Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
,,Note
If your TV accepts progressive format signals,
you must use this connection and set
[Progressive Scan] in [Display] setup to [On]
(See page 17).
HT356SD-D0_BGBRLL1_ENG_5763.indd 13
2011-10-10 �� 9:32:31
14
Connecting
Video Connection
Connect the MONITOR jack on the unit to the video
in jack on the TV using a video cable.
You can hear the sound through the system’s
speakers.
Optional Equipment
Connection
AUX IN Connection
Connect an Output of auxiliary device to the AUX
(L/R) INPUT Connector.
2
Connecting
If your TV has only one output for audio (mono),
connect it to the left (white) audio jack on the unit.
SCART Connection
Connect the SCART jack on the unit to the SCART in
jack on the TV using a video cable.
You can hear the sound through the system’s
speakers.
AUDIO IN (P. IN) Connection
Connect an OUTPUT of portable device (MP3 or
PMP etc) to the P. IN connector.
MP3 player, etc...
HT356SD-D0_BGBRLL1_ENG_5763.indd 14
2011-10-10 �� 9:32:31
Connecting
15
USB Connection
Antenna Connection
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
Connect the supplied FM antenna for listening to
the radio.
Connect the FM Wire antenna to the FM antenna
connector.
2
Connecting
Removing the USB Device from the unit
1. Choose a different function mode or
press STOP (Z) twice in a row.
2. Remove the USB device from the unit.
HT356SD-D0_BGBRLL1_ENG_5763.indd 15
,,Note
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it
as horizontal as possible.
2011-10-10 �� 9:32:32
16
System Setting
Adjust the Setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
You can also set a language for the subtitles and
the Setup menu, among other things. For details on
each Setup menu item, see pages 16 to 19.
OSD Initial language settings
- Optional
3
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using
the unit. English will be selected as the initial
language.
1. Press POWER to turn the unit on. The language
setup menu will appear on the screen.
To display and exit the Setup
Menu
1. Select the DVD/CD or USB function by pressing
FUNCTION.
2. Press SETUP.
Displays the [Setup] Menu.
3. Press SETUP or RETURN to exit in the [Setup]
Menu.
About help menu for Setup
Menu
Buttons
Operation
WS
Moving to another
menu.
A
Moving to previous
level.
Select
D
Moving to next level
or selecting menu.
x
RETURN
To exit the [Setup]
menu or [ 5.1 Speaker
Setup].
b
ENTER
w/s
Move
a
Prev.
d
To confirm menu.
LANGUAGE
2. Use WSAD to select a language then press
ENTER.
The confirm menu will appear.
3. Use AD to select the [Enter] then press ENTER
to finish the language setup.
HT356SD-D0_BGBRLL1_ENG_5763.indd 16
Menu Language
Select a language for the Setup menu and then on
screen display.
Disc Audio / Disc Subtitle / Disc
Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
2011-10-10 �� 9:32:32
System Setting
[Original]
Refers to the original language in which the
disc was recorded.
TV Output Select
Select an option according to the TV connection
type.
[Other]
[RGB]
To select another language, press numeric
buttons and then ENTER to enter the
corresponding 4-digit number according to
the language code list on the page 30. If you
enter the wrong language code, press CLEAR.
When your TV is connected with the SCART
jack.
[Off (for Disc Subtitle)]
Turn off Subtitle.
DISPLAY
Select which screen aspect to use based on the
shape of your TV screen.
[YPBPR]
When your TV is connected with the
COMPONENT/ PROGRESSIVE SCAN jacks on the
unit.
,,Note
If you change TV Output Select to RGB from
YPbPr on the setup menu especially when
connecting the unit in the way of component
video connection, the screen turns black.
In that case, connect the video cable to
MONITOR jack and select YPbPr on the setup
menu again.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
Display Mode
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
[Letterbox]
Displays a wide picture with bands on the
upper and lower portions of the screen.
[Panscan]
3
System Setting
TV Aspect
17
Progressive Scan (For Component
Video connections)
Selects whether the COMPONENT
VIDEO(PROGRESSIVE SCAN) OUTPUT jacks output
progressive signal. If your TV accepts progressive
format signals, you will enjoy accurate color
reproduction and high quality image by selecting
[On]. If your TV does not accept progressive format
signals, select [Off ].
If you set Progressive Scan to [On] in error, you must
reset the unit. First, remove the disc in the unit.
Next, press and hold STOP (Z) for five seconds.
The video output will be restored to the standard
setting, and a picture will be visible on your TV.
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with
Pan Scan, the picture is displayed at Letterbox
ratio.)
HT356SD-D0_BGBRLL1_ENG_5763.indd 17
2011-10-10 �� 9:32:32
18
System Setting
AUDIO
[Volume]
DRC (Dynamic Range Control)
Press AD to adjust the output level of the
selected speaker.
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
Vocal
Select [On] to mix karaoke channels into normal
stereo.
This function is effective for multi-channel karaoke
DVDs only.
3
5.1 Speaker Setup
System Setting
Make the following settings for the built-in 5.1
channel surrounds decoder.
1. Press SETUP.
2. Use WS to select AUDIO menu and then press
D.
3. Use WS to select [5.1 Speaker setup] menu
and then press D.
4. Press ENTER
The [5.1 Speaker setup] appears.
[Distance]
After you connected speakers to your unit,
set the Distance between the speakers and
your listening point if the distance of Center
or Rear speakers is bigger than the distance
of Front speakers. This allows the sound from
each speaker to reach the listener at the same
time. Press AD to adjust the Distance of the
selected speaker. This distance is equivalent to
a difference of the distance between Center or
Rear speaker and Front speakers.
[Test]
Press AD to test the signals of each speaker.
Adjust the volume to match the volume of test
signals memorized in the system.
LOCK (Parental Control)
Initial Setting of the Area Code:
When you use this unit for the first time, you have
to set the Area Code.
1. Select the [Lock] menu and then press D.
5. Use AD to select the desired speaker.
6. Adjust options using WSAD buttons.
7. Press RETURN to confirm your selection. Return
to the previous menu.
[Speaker]
Select a speaker that you want to adjust.
2. Press D.
To access the [Lock] options, you must input the
password you have created. Input a password
and press ENTER. Enter it again and press
ENTER to verify. If you make a mistake before
pressing ENTER, press CLEAR.
3. Select the first character using WS buttons.
4. Press ENTER and select the second character
using WS buttons.
5. Press ENTER to confirm your Area code
selection.
,,Note
Certain speaker settings are prohibited by the
Dolby Digital licensing agreement.
[Size]
Since the speaker settings are fixed, you cannot
change the settings.
HT356SD-D0_BGBRLL1_ENG_5763.indd 18
2011-10-10 �� 9:32:32
System Setting
Rating
Area Code
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 29.
1. Select [Rating] on the [Lock] menu then press
D.
2. Input a password and press ENTER.
1. Select [Area Code] on the [Lock] menu then
press D.
3. Select a rating from 1 to 8 using the WS
buttons.
3. Select the first character using WS buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
19
2. Input a password and press ENTER.
4. Press ENTER and select the second character
using WS buttons.
5. Press ENTER to confirm your Area code
selection.
[Unlock]
4. Press ENTER to confirm your rating selection.
Password
You can enter or change password.
1. Select [Password] on the [Lock] menu and then
press D.
2. Input a password and press ENTER.
To change the password, press ENTER when
the [Change] option is highlighted. Input a
password and press ENTER. Enter it again and
press ENTER to verify.
3. Press SETUP to exit the menu.
,,Note
If you forget your password, you can clear it
using the following steps:
OTHERS
3
DivX(R) VOD
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, Inc. This is an official DivX
Certified® device that plays DivX video. Visit www.
divx.com for more information and software tools
to convert your files into DivX video.
System Setting
If you select unlock, parental control is not
active and the disc plays in full.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies.
To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete
your registration.
[Register]
Displays the registration code of your unit.
1. Press SETUP to display the Setup menu.
[Deregister]
2. Input the 6-digit number “210499” and
press ENTER. The password is cleared.
Deactivate your unit and display the deactivation
code.
,,Note
All the downloaded videos from DivX VOD
can only be played back on this unit.
HT356SD-D0_BGBRLL1_ENG_5763.indd 19
2011-10-10 �� 9:32:32
4
Operating
20 Operating
Basic Operations
1. Insert the disc by pressing OPEN/CLOSE or
connect the USB device to the USB port.
2. Select the DVD/ CD or USB function by pressing
FUNCTION.
3. Select a file (or track/ title) you want to play by
pressing WSAD.
To
Stop
Press Z
Playback
Press d
Pause
Press M
Frame-by-Frame Press M repeatedly to play
playback
title Frame-by-Frame.
,,Note
When playing a disc or USB Flash Drive
containing with DivX, MP3/ WMA and JPEG
files together, you can select menu of files
which you would like to play by pressing
MENU. If “This file has non-supported type
on the unit” pops up, select an appropriate file
by pressing MENU.
4
Do this
Skipping to the
next/previous
chapter/track/
file
Operating
Locating a
point quickly by
playing a file in
fast forward or
fast reverse
Playing
repeatedly or
randomly
During playback, pressC
or V to go to the next
chapter/track or to return to
the beginning of the current
chapter/track.
Press C twice briefly to step
back to the previous chapter/
track.
During playback, pressc or
v repeatedly to select the
required scan speed.
To return to normal speed,
press PLAY.
Press REPEAT/RANDOM
repeatedly, and the current
title, chapter or track will be
played back repeatedly or
randomly.
- Random play mode : only
music files.
Slowing down
the playing
speed
HT356SD-D0_BGBRLL1_ENG_5763.indd 20
In the pause mode, press
SCAN (c or v) to
select the required speed.
(The reverse playback is not
supported on Divx files.)
2011-10-10 �� 9:32:32
Operating
Other Operations
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
1. Press DISPLAY to show various playback
information.
The displayed items differ depending on the
disc type or playing status.
2. You can select an item by pressing WS and
change or select the setting by pressing AD.
21
To display the DVD Menu
r
When you play a DVD which contains several
menus, you can select the menu you want using
the menu.
1. Press MENU.
The disc’s menu appears.
2. Select the menu by using WSAD.
3. Press PLAY to confirm.
To display the DVD Title
r
Title – Current title number/ total number of titles.
When you play a DVD which contains several titles,
you can select the title you want using the menu.
Chapter – Current chapter number/total number of
chapters.
1. Press TITLE.
The disc’s title appears.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
2. Select the menu by pressing
WSAD.
Subtitle – Selected subtitle.
3. Press PLAY to confirm.
Sound – Selected sound mode.
,,Note
If any button is not pressed for a few seconds,
the onscreen display disappears.
Selecting a subtitle language
ry
Operating
Angle – Selected angle/total number of angles.
4
During playback, press SUBTITLE( ] ) repeatedly
to select a desired subtitle language.
1.5 times speed playback
r
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
1. During playback, press PLAY(d) to play at 1.5
times speed. “dX1.5” appears on the screen.
2. Press PLAY(d) again to exit.
HT356SD-D0_BGBRLL1_ENG_5763.indd 21
2011-10-10 �� 9:32:32
22 Operating
Starting play from selected
time
Programmed Playback
ry
The program function enables you to store your
favourite files from any disc or USB device.
To start playing at any chosen time on the file or
title.
1. Press DISPLAY during playback.
2. Press WS to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by using
numerical buttons.
4. Press ENTER to confirm. Playback starts from
the selected time.
4
Operating
Last Scene Memory
r
This unit memorizes the last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the player or
switch off (Stand-by mode) the unit. If you load a
disc that has the scene memorized, the scene is
automatically recalled.
Changing the character set to
display DivX® subtitle correctly
y
If the subtitle does not display properly during
playback press and hold SUBTITLE for about 3
seconds then press AD or SUBTITLE to select
another language code until the subtitle is
displayed properly and then press ENTER.
HT356SD-D0_BGBRLL1_ENG_5763.indd 22
tu
A program can contain 30 tracks/ files.
1. Select the DVD/CD or USB function by pressing
FUNCTION.
2. To add a music(s) on the program list, press
PROG./MEMO. to enter the program edit mode
({ mark appears on the menu).
3. Select a desired music on the [List] by using the WS then press ENTER to add the music to
the program list.
4. Select music from the program list then press
ENTER to start programmed playback.
5. Press PROG./MEMO. to exit the program edit
mode ({ mark disappears on the menu).
Erasing a file from Program List
1. Press PROG./MEMO. to enter the program edit
mode ({ mark appears on the menu).
2. Use WS to select the track that you wish to
erase from the Program list.
3. Press CLEAR.
Erasing the Complete Program List
Use WSAD to select [Clear All] then press ENTER.
,,Note
The programs are also cleared when the disc
or USB device is removed, the unit is switched
to power off or the function is switched to
others.
2011-10-10 �� 9:32:32
Operating 23
Viewing a PHOTO file
i
Listening to music during slide
show
This unit can play discs with photo files.
i
1. Select the DVD/CD or USB function by pressing
FUNCTION.
You can listen to music during slide show, if the
disc contain music and photo files together. Use
WSAD to highlight (~) icon then press
ENTER to start slide show.
2. Press WS to select a folder, and then press
ENTER.
A list of files in the folder appears.
If you are in a file list and want to return to the
previous folder list, use the WS buttons on the
remote to highlight
and press ENTER.
,,Note
This function is available only in disc.
3. If you want to view a particular file, press WS
to highlight a file and press ENTER or PLAY.
While viewing a file, you can press STOP to move
to the previous menu (JPEG menu).
Sleep Timer Setting
Viewing photo files as a slide
show
To check the remaining time, press SLEEP.
1. Use WSAD to highlight (
) icon then
press ENTER to start slide Show.
2. You can change slide show speed using ) icon is highlighted.
AD when (
About help menu for slide show
Menu
w/s
/
a/ d
Prev./ Next
x
Hide
b
Buttons
Operation
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
,,Note
You can check the remaining time before the
unit turns off.
Dimmer
W/S
Rotating the
picture
Press SLEEP once. The display window will be
darken by half. To cancel it, press SLEEP repeatedly
until dimmer gets off.
A/D
Moving to
another file
Turn off the sound temporarily
RETURN
Closing the slide
show
ENTER
Hiding the help
menu
HT356SD-D0_BGBRLL1_ENG_5763.indd 23
4
Operating
i
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will
turn off.
Press MUTE to mute your unit.
You can mute your unit, for example, to answer
the telephone, the “MUTE” displayed in the display
window.
2011-10-10 �� 9:32:33
24 Operating
Screen Saver
in the display window.
The screen saver appears when you leave the unit
in stop mode for about five minutes.
System Select - Optional
You must select the appropriate system mode for
your TV system. If “NO DISC” appears in the display
window, press and hold PAUSE/STEP (M) for more
than five seconds to select a system.
Displaying file information
(ID3 TAG )
While playing an MP3 file containing file
information, you can display the information by
pressing DISPLAY.
4
Radio Operations
Operating
Be sure that both FM aerials are connected. (Refer
to the page 15)
Listening to the Radio
1. Press FUNCTION until FM appears in the display
window.
The last received station is tuned in.
2. Press and hold TUN.(-/+) for about two seconds
until the frequency indication starts to change,
then release. Scanning stops when the unit
tunes in a station.
or
Press TUN.(-/+) repeatedly.
3. Adjust the volume by rotating VOL. on the front
panel or by pressing VOL + or - on the remote
control repeatedly.
Presetting the Radio Stations
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
1. Press FUNCTION until FM appears in the display
window.
4. Press PRESET (WS) to select the preset
number you want.
5. Press PROG./MEMO.
The station is stored.
6. Repeat the steps 2 to 5 to store other stations.
Deleting all the saved stations
1. Press and hold PROG./MEMO. for two seconds.
“ERASE ALL” will flash up on the unit display.
2. Press PROG./MEMO. to erase all of the saved
radio stations.
Improving poor FM reception
Press PLAY (d) (MO./ST.) on the remote control.
This will change the tuner from stereo to mono and
usually improve the reception.
Seeing information about a
radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about
the radio station being listened to. Press RDS
repeatedly to cycle through the various data types.
PS (Programme Service Name)
The name of the channel will appear in the
display.
PTY (Programme Type Recognition)
The programme type (e.g. Jazz or News) will
appear in the display.
RT (Radio Text)
A text message contains special information
from the broadcast station. This text may
scroll across the display.
CT (Time controlled by the channel)
This shows the time and date as broadcast by
the station.
You can search the radio stations by programme
type by pressing RDS. The display will show the last
PTY in use. Press PTY one or more times to select
your preferred programme type. Press and hold
AD. The tuner will search automatically. When a
station is found the search will stop.
2. Select the desired frequency by using TUN.
(-/+).
3. Press PROG./MEMO. a preset number will flash
HT356SD-D0_BGBRLL1_ENG_5763.indd 24
2011-10-10 �� 9:32:33
Operating 25
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using EQ/ LG EQ. You can change the EQ/ LG
EQ using AD arrow key while the EQ/ LG EQ
information is displayed on.
,,Note
yy In some of surround modes, on some
speakers, there’s no sound or low sound. it,
depends on the mode of surround and the
source of audio, it is not defective.
yy You may need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
The displayed items for the Equalizer may be
different depending on sound sources and effects.
On Display
Description
NAT PLUS
You can enjoy the natural
sound effect same as a
5.1-channel.
NATURAL
You can enjoy comfortable
and natural sound.
Regionally optimized
equalizer
ARABIC/ PERSIAN/ INDIA/
REGUETON/ MERENGUE/
4
Operating
Local
Specialization
sound effect. (DANGDUT/
SALSA/ SAMBA/ CUMBIA/
AFRO)
AUTO EQ
POP
CLASSIC
JAZZ
ROCK
MP3 OPT
BASS
Realizes the sound equalizer
that is the most similar to the
genre of which is included in
the MP3 ID3 tag of song files.
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock pop, jazz or classic
concert.
This function is optimized
for compressible MP3 file. It
improves the treble sound.
During playback, Reinforces
the treble, bass and surround
sound effect.
VIRTUAL
You can enjoy more virtual
surround sound.
BYPASS
You can enjoy the sound
without equalizer effect.
HT356SD-D0_BGBRLL1_ENG_5763.indd 25
2011-10-10 �� 9:32:33
26 Operating
Advanced Operations
Listening to music from your
portable player or external
device
The unit can be used to play the music from many
types of portable player or external devices.
1. Connect the portable player to the P. IN(PORTABLE IN) connector of the unit.
Or
Connect the external device to the AUX
connector of the unit.
Or
4
Connect the external device to the SCART
connector of the unit.
2. Turn the power on by pressing POWER.
Operating
3. Select the PORTABLE, AUX, TV-AUDIO function
by pressing FUNCTION.
4. Turn the portable player or external device and
start it playing.
Recording to USB
1. Connect the USB device to the unit.
2. Select a DVD/ CD function by pressing
FUNCTION.
,,Note
yy You can check the recording percentage
rate for the USB record on the screen
during the recording.
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored.
yy Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
yy If USB recording does not work, the
message like “NO USB”, “ERROR”, “USB FULL”
or “NO REC” is displayed on the display
window.
yy On CD-G disc, USB recording is not
supported.
yy You may not store more than 999 files.
yy It’ll be stored as TRK_001 on CD FOLDER.
yy Recording is supported only in Audio CDs.
The making of unauthorized copies of copyprotected material, including computer programs,
files, broadcasts and sound recordings, may be
an infringement of copyrights and constitute a
criminal offense. This equipment should not be
used for such purposes.
Be responsible
Respect copyrights
One track recording - You can record to USB after
playing the file you want.
All tracks recording - You can record to USB after
stop.
Program list recording - After showing the
programmed list, you can record it to USB.
3. Start the recording by pressing X REC.
4. To stop recording, press Z STOP.
HT356SD-D0_BGBRLL1_ENG_5763.indd 26
2011-10-10 �� 9:32:33
Troubleshooting 27
Troubleshooting
PROBLEM
No power
No picture
CORRECTION
Plug the power cord into the wall outlet securely.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
Connect the video cables securely to both the TV and unit.
Select the correct input mode of the unit so you can hear the sound
from the unit.
There is little or no sound
Connect the audio cables into the connection terminals correctly.
Replace with a new audio cable.
The DVD picture quality is poor
Clean the disc using a soft cloth with outward strokes.
Insert a disc.
A DVD/CD will not play
Insert a playable disc (check the disc type, colour system and
regional code).
Place the disc with the label or printed side facing upwards.
Enter your password or change the rating level.
5
Clean the disc using a soft cloth with outward strokes.
Move unit and audio components further away from your TV.
Check the antenna connection and adjust its position.
Radio stations can’t be tuned in
properly.
Attach an external aerial if necessary.
Tune to the station manually.
Troubleshooting
Humming noise heard while a DVD
or CD is playing
Preset some radio stations, see page 24 for details.
The remote is not pointed directly at the unit.
Point the remote directly at the unit.
The remote is too far from the unit.
Use the remote within 23 feet (7m) of the unit.
The remote control doesn’t work
well / at all
There is an obstacle in the path between the remote control and
the unit.
Remove the obstacle.
The battery in the remote control are flat.
Replace the battery with new ones.
HT356SD-D0_BGBRLL1_ENG_5763.indd 27
2011-10-10 �� 9:32:33
28 Appendix
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
yy Do not use volatile liquids such as insecticide
spray near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Maintaining the Unit
6
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
HT356SD-D0_BGBRLL1_ENG_5763.indd 28
2011-10-10 �� 9:32:33
Appendix 29
Area Code List
Choose an area code from this list.
Area
Afghanistan Code Area
AF Fiji Code Area
Code Area
Code
FJ Monaco MC Singapore SG
SK
Argentina AR Finland FI Mongolia MN Slovak Republic Australia AU France FR Morocco MA Slovenia Austria AT Germany DE Nepal NP South Africa ZA
Belgium BE Great Britain GB Netherlands NL South Korea KR
Bhutan BT Greece GR Antilles AN Spain ES
Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK
SI
Brazil BR Hong Kong HK Nigeria NG Sweden SE
Cambodia KH Hungary HU Norway NO Switzerland CH
Canada CA India IN Oman OM Taiwan TW
Chile CL Indonesia ID Pakistan PK Thailand China CN Israel IL Panama PA Turkey TR
Colombia CO Italy IT Paraguay PY Uganda UG
Congo CG Jamaica JM Philippines PH Ukraine UA
Costa Rica CR Japan JP Poland PL United States US
Croatia HR Kenya KE Portugal PT Uruguay UY
Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ
Denmark DK Libya Ecuador EC Luxembourg Egypt EG Malaysia El Salvador SV Maldives MY Saudi Arabia MV Senegal Ethiopia ET Mexico MX
Vietnam RU Zimbabwe SA
SN
VN
ZW
6
Appendix
HT356SD-D0_BGBRLL1_ENG_5763.indd 29
LY Russian LU Federation TH
2011-10-10 �� 9:32:33
30 Appendix
Language Code List
Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu].
6
Appendix
Language
Code
Language
Code
Language
Code
Language
Afar 6565
French 7082
Lithuanian 7684
Sindhi 8368
Afrikaans 6570
Frisian 7089
Macedonian 7775
Singhalese 8373
Albanian 8381
Galician 7176
Malagasy 7771
Slovak 8375
Ameharic 6577
Georgian 7565
Malay 7783
Slovenian 8376
Arabic 6582
German 6869
Malayalam 7776
Spanish 6983
Armenian 7289
Greek 6976
Maori 7773
Sudanese 8385
Assamese 6583
Greenlandic 7576
Marathi 7782
Swahili 8387
Aymara 6588
Guarani 7178
Moldavian 7779
Swedish 8386
Azerbaijani 6590
Gujarati 7185
Mongolian 7778
Tagalog 8476
Bashkir 6665
Hausa 7265
Nauru
7865
Tajik 8471
Basque 6985
Hebrew 7387
Nepali 7869
Tamil 8465
Bengali; Bangla 6678
Hindi 7273
Norwegian 7879
Telugu 8469
Bhutani 6890
Hungarian 7285
Oriya 7982
Thai 8472
Bihari 6672
Icelandic 7383
Panjabi 8065
Tonga 8479
Breton 6682
Indonesian 7378
Pashto, Pushto 8083
Turkish 8482
Bulgarian 6671
Interlingua 7365
Persian 7065
Turkmen 8475
Burmese 7789
Irish 7165
Polish 8076
Twi 8487
Byelorussian 6669
Italian 7384
Portuguese 8084
Ukrainian 8575
Chinese 9072
Japanese 7465
Quechua 8185
Urdu 8582
Croatian 7282
Kannada 7578
Rhaeto-Romance 8277
Uzbek 8590
Czech 6783
Kashmiri 7583
Rumanian 8279
Vietnamese 8673
Danish 6865
Kazakh 7575
Russian 8285
Volapük 8679
Dutch 7876
Kirghiz 7589
Samoan 8377
Welsh 6789
English 6978
Korean 7579
Sanskrit 8365
Wolof 8779
Esperanto 6979
Kurdish 7585
Scots Gaelic 7168
Xhosa 8872
Estonian 6984
Laothian 7679
Serbian 8382
Yiddish 7473
Faroese 7079
Latin 7665
Serbo-Croatian 8372
Yoruba 8979
Fiji 7074
Latvian, Lettish 7686
Shona 8378
Zulu 9085
Finnish 7073
Lingala 7678
HT356SD-D0_BGBRLL1_ENG_5763.indd 30
Code
2011-10-10 �� 9:32:33
Appendix
31
Trademarks and
Licenses
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
DivX®, DivX Certified® and associaated logos
are trademark of DivX, Inc., and are used under
license.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
6
Appendix
HT356SD-D0_BGBRLL1_ENG_5763.indd 31
2011-10-10 �� 9:32:33
32 Appendix
Specifications
General
Power requirements
200 - 240 V , 50/ 60 Hz
Power consumption
45 W
Dimensions (W x H x D)
Approx. 360 x 65 x 320 mm without foot
Net Weight (Approx.)
2.5 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1/ SCART (TO TV)
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
ANALOG AUDIO IN
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
PORT. IN
0.5Vrms (3.5 mm stereo jack)
System
6
Appendix
Laser
Semiconductor laser, wavelength: 650 nm
Signal system
Standard NTSC/ PAL color TV system
Frequency response
20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Signal-to-noise ratio
More than 80 dB
Harmonic distortion
0.05 % at 1 W
Dynamic range
More than 85 dB
Bus Power Supply (USB)
DC 5 V 0 500 mA
Amplificador
Stereo mode
Surround mode
45 W + 45 W (4 Ω at 1 kHz)
Front
45 W + 45 W (THD 1 %)
Center
45 W
Surround
45 W + 45 W (4 Ω at 1 kHz)
Subwoofer
75 W (8 Ω at 60 Hz)
Tuner
FM Tuning Range
HT356SD-D0_BGBRLL1_ENG_5763.indd 32
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
2011-10-10 �� 9:32:34
Appendix 33
Front Speaker
Type
1 Way 1 Speaker
Impedance Rated
4Ω
Input Power
45 W
Max. Input Power
90 W
Net Dimensions (W x H x D)
113 x 113 x 84 mm
Net Weight
0.34 kg
Rear Speaker
Type
1 Way 1 Speaker
Impedance Rated
4Ω
Input Power
45 W
Max. Input Power
90 W
Net Dimensions (W x H x D)
113 x 113 x 84 mm
Net Weight
0.38 kg
Centre Speaker
Type
1 Way 1 Speaker
Impedance Rated
4Ω
Input Power
45 W
Max. Input Power
90 W
Net Dimensions (W x H x D)
113 x 113 x 84 mm
Net Weight
0.34 kg
6
Subwoofer
1 Way 1 Speaker
Impedance Rated
8Ω
Input Power
75 W
Max. Input Power
150 W
Net Dimensions (W x H x D)
155 x 325 x 265 mm
Net Weight
3 kg
Appendix
Type
Design and specifications are subject to change without notice.
HT356SD-D0_BGBRLL1_ENG_5763.indd 33
2011-10-10 �� 9:32:34
34 Warranty
Technology with the human touch
GUARANTEE
• LG Electronics U.K. Ltd. will provide the following services in order toexpedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a period
of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the repair of this LG equipment, for a period of 12 months from the
original date of purchase. These claims must be made in accordance with the published scale of service charges and relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made to
the apparatus, or if non standard components are used or if the serial number of the apparatus is removed,
defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a receipted
account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become exhausted
or worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
• REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE SURRENDERED
AT THE TIME GUARANTEE SERVICE IS PROVED.
• Product Registration Card :
It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This
will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should
modifications be necessary.
7
• To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm
Warranty
MODEL NO.*
SERIAL NO.*
DATE OF PURCHASE.*
In all cases of difficulty - consult your LG dealer from whom the product was purchased
LGEUK Website : www.lge.co.uk
( service website : www.lgelectronics.co.uk )
HT356SD-D0_BGBRLL1_ENG_5763.indd 34
2011-10-10 �� 9:32:34
HT356SD-D0_BGBRLL1_ENG_5763.indd 35
2011-10-10 �� 9:32:34
Download PDF

advertising