LG | HT353SD | LG HT353SD Owner’s Manual

HT353SD-D0_ENG_UK_MFL56762613
HT353SD
(HT353SD-D0, SH33SD-S/W)
ENGLISH
DVD/CD RECEIVER
Read the manual carefully before using the unit
R
P/N: MFL56762613
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to alert
the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined
space such as a book case or similar unit.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
CLASSE 1 PRODUIT LASER
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future
reference. Should the unit require maintenance, contact
an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to
open the enclosure. Visible laser radiation when open.
DO NOT STARE INTO BEAM.
Note:
The marking of product shall be on the exterior of the
apparatus
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled with
liquids, such as vases, should be placed on the
apparatus.
2
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits.
Check the specification page of this owner's manual to
be certain.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement
part by an authorized servicer.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord
exits the appliance.
To disconnect power from the mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
POWER: This unit operates on a mains supply of 200-240V~, 50/60Hz.
WIRING: This unit is supplied with a BSI 1363 approved 13 amp mains
plug, fused at 5 amp. When replacing the fuse always use a 5 amp BS
1362, BSI or ASTA approved type. Never use this plug with the fuse
cover omitted. To obtain a replacement fuse cover contact your dealer.
If the type of plug supplied is not suitable for the mains sockets in your
home, then the plug should be removed and a suitable type fitted.
Please refer to the wiring instructions below:
WARNING: A mains plug removed from the mains lead of this unit
must be destroyed. A mains plug with bared wires is hazardous if
inserted in a mains socket. Do not connect either wire to the earth pin,
marked with the letter E or with the earth symbol
or coloured green
or green and yellow. If any other plug is fitted,
use a 5 amp fuse, either in the plug, or at the distribution board.
IMPORTANT: The wires in this mains lead are coloured in accordance
with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours of the wires in the
mains lead of this unit may not correspond with the coloured marking
identifying the terminals in your plug, proceed as follows: The wire
which is coloured blue must be connected to the terminal which is
marked with the letter N or coloured black. The wire which is coloured
brown must be connected to the terminal which is marked with the
letter L or coloured red.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached
to a product it means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed by
the government or the local authorities.
3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.
4. For more detailed information about disposal of your
old appliance, please contact your city office, waste
disposal service or the shop where you purchased the
product.
This product is manufactured to comply with EMC
Directive 2004/108/EC and Low Voltage Directive
2006/95/EC.
European representative :
LG Electronics Service Europe B.V. Veluwezoom 15,
1327 AE Almere, The Netherlands
(Tel : +31-036-547-8940)
QUICK SETUP GUIDE
Speaker System Connection
ENGLISH
Connect the speaker wires the speaker terminals.
To obtain the best possible surround sound, adjust
the speaker parameters (volume, distance, etc.).
Notes:
Be sure to match the speaker wires to the
appropriate terminal on the components, + to +
and – to –. If the cables are reversed, the
sound will be distorted and will lack bass.
If you use front speakers with low maximum
input rating, adjust the volume carefully to avoid
excessive output on the speakers.
Be careful of the following
Be careful to make sure children not to put their
hands or any objects into the *speaker duct.
*Speaker duct: A hall for plentiful bass sound on
speaker cabinet(enclosure).
5.1 Speaker Setup
Make the following settings for the built-in 5.1 channel surround decoder.
1. Press ENTER and 5.1 Speaker Setup menu appears.
2. Use b / B to select the desired speaker.
3. Adjust options using v / V / b / B buttons.
4. After setting, returns to the previous menu by pressing RETURN button.
Speaker selection
Select a speaker that you want to adjust. [Front speaker (Front L), Front speaker (Front R), Center Speaker (Center),
Subwoofer (SubWoofer), Rear speaker (Rear L), Rear speaker (Rear R)]
Note:
Certain speaker settings are prohibited by the Dolby Digital licensing agreement.
Size
Since the speaker settings are fixed, you cannot change the settings.
Volume
Press b / B to adjust the output level of the selected speaker. (-6dB ~ 6dB)
Distance
If you connected speakers to your DVD/CD Receiver, setting the Distance lets the speakers know how far the sound
has to travel to reach your set listening point. This allows the sound from each speaker to reach the listener at the
same time.
Press b / B to adjust the Distance of the selected speaker.
Test
Press b / B to test the signals of each speaker. Adjust the volume to match the volume of test signals memorized in
the system.
Front Left (L) → Center → Front Right (R) → Rear Right (R) → Rear Left (L) → SubWoofer
3
Introduction
Types of Playable Discs
Installation
Before Use . . . . . . . . . . . . . . . . . .
TV Connection . . . . . . . . . . . . . . .
Antenna Connection . . . . . . . . . .
Speaker System Connection . . .
Optional Equipment Connection
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.4
.5
.5
.5
.5
Operation
Operate using the Front Panel . . . . . . . . . . . . . . . .6
Operate using the Remote Control . . . . . . . . . . .6-8
Setup
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
General Operation . . . . . . . . . . . . . . . . . . . . . . . . . .8
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Lock (Parental Control) . . . . . . . . . . . . . . . . . . . . .9
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Presetting the Radio Stations . . . . . . . .10
Playing an Audio CD or
MP3/WMA/JPEG/DivX file
In addition, this unit can play a DVD-RW, DVD+RW,
CD-G and CD-R or CD-RW that contains audio titles,
MP3, WMA, JPEG or DivX files.
Notes:
Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD-RW, DVD+RW)
disc itself, some CD-R/RW (or DVD-RW, DVD+RW)
discs may not be played on the unit.
For DVD-R/RW Discs, only ones rewritten in video
mode and finalized are supported on this player.
When there are a lot of data in a disc, it may take
longer to be read on this player than on other model.
Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
Regional Code
This unit has a regional code printed on the rear of the
unit. This unit can play only DVD discs labelled as the
same as the rear of the unit or “ALL”.
Notes on Regional Codes
Playing an Audio CD or MP3/WMA file . . . . . . . . .10
Programmed playback . . . . . . . . . . . . . . . . . . . . .10
Viewing a JPEG file . . . . . . . . . . . . . . . . . . . . .10-11
Playing a DivX Movie file . . . . . . . . . . . . . . . . . . . .11
Additional features . . . . . . . . . . . . . . . . . . . . . . . .11
If you try to play a DVD with a different regional code
from your player, the message “Check Regional Code”
appears on the TV screen.
RDS Operation . . . . . . . . . . . . . . . . . . . .11
Reference
Language Codes
Area Codes . . . .
Troubleshooting
Specifications . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.12
.12
.13
.14
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and
worldwide patents issued & pending. DTS and DTS Digital
Surround are registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-2007 DTS, Inc. All
Rights Reserved.
Before Use
About the
Symbol Display
“
” may appear on your TV display during operation
and indicates that the function explained in this owner’s
manual is not available on that specific DVD video disc.
Symbol Used in this Manual
A section whose title has one of the following symbols is
applicable only to the disc represented by the symbol.
DVD-V
DVD and finalized DVD±R/RW
ACD
Audio CDs
MP3 MP3 files
WMA
WMA files
JPEG JPEG files
4
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
Manufactured under license from Dolby Laboratories.
Please ensure that the proper above notice is included in the
owner’s manual.
DivX DivX files
The making of unauthorized copies of copy-protected material,
including computer programs, files, broadcasts and sound
recordings, may be an infringement of copyrights and constitute
a criminal offence. This equipment should not be used for such
purposes.
Be responsible respect copyrights
Installation
ENGLISH
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
Be careful of the following
Be careful to make sure children not to put their hands or
any objects into the *speaker duct.
*Speaker duct: A hall for plentiful bass sound on speaker
cabinet(enclosure).
TV Connection
Make one of the following connections, depending on the
capabilities of your existing equipment.
Tips:
Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
DVD/CD Receiver. Use one of the connections described
below.
Please refer to the manuals of your TV, VCR, Stereo System
or other devices as necessary to make the best connections.
Caution:
Make sure the DVD/CD Receiver is connected directly to the
TV. Select the correct AV input on your TV.
Do not connect your DVD/CD Receiver to the TV via your
VCR. The DVD image could be distorted by the copy
protection system.
SCART connection
Connect the EURO AV OUTPUT (TO TV) socket on the DVD/CD
Receiver to the corresponding jacks on the TV using the scart
cable (T).
Component Video connection
Connect the COMPONENT VIDEO OUT jacks from the DVD/CD
Receiver to the corresponding jacks on the TV using a Y PB PR
cable (C).
If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD/CD
Receiver’s progressive scan output for higher video
resolution.
If your TV does not accept your resolution setting, abnormal
picture appears on the screen. Please read owner’s manual
for TV then set the resolution that your TV can accept.
Composit Video connection
Connect the MONITOR jack from the DVD/CD Receiver to the
Video IN jack on the TV using the video cable supplied (V).
Antenna Connection
Connect the supplied FM antenna for listening to the radio.
Connect the FM Wire aerial to the FM aerial connector.
Notes:
Be sure to fully extend the FM wire aerial.
After connecting the FM Wire aerial, keep it as horizontal as
possible.
Speaker System Connection
Connect the speaker wires the speaker terminals.
To obtain the best possible surround sound, adjust the speaker
parameters (volume, distance, etc.).
Notes:
Be sure to match the speaker wires to the appropriate
terminal on the components, + to + and – to –. If the cables
are reversed, the sound will be distorted and will lack bass.
If you use front speakers with low maximum input rating,
adjust the volume carefully to avoid excessive output on the
speakers.
Optional Equipment Connection
Connect a VCR to the AUX IN connectors.
5
Operation
1
2
3
4
12
5
6 7
11 10
8
9
Operate using the Front Panel
1. (
/[)POWER button
Lights red when the receiver is in Standby mode (off)
2. DISC Tray
3. DISPLAY Window
4. Remote Sensor:RemoteControl Operation Range
Distance: About 23 ft (7 m) from the front of the Remote
Sensor
Angle: About 30° in each direction in front of the Remote
Sensor
5. OPEN/CLOSE Opens and closes the disc tray.
6. • (B/X)PLAY/PAUSE
• FUNC.( ) Press and hold down this button
about 3 seconds, then press repeatedly to select other
→ TV -AUDIO
function. (DVD/CD →USB → AUX→
→PORTABLE→
→FM )
7.VSM Press VSM to set the VIRTUAL sound.
• 3D STEREO Realtime 3D positioned sound rendering
technology with stereo sources, optimized for stereo speakers.
Listeners may experience amazing virtual surround effects
with their own multimedia players.
• Multichannel sound The Multichannel sound changes the
sound in 5.1 ch into a virtual one in the 10.1 ch so that it
provides such a feeling that you listen to the sound
simultaneously from the right and left speakers and center
speaker.
-
./>
>)
8. TUNING(-/+)/SKIP/SCAN(.
10. USB Port Connect the USB port of a USB Memory
(or MP3 player, etc.) to the USB port on the front of the unit.
Removing the USB Device from the unit
1. Choose a different function mode or press STOP (x) twice in
a row.
2. Remove the USB device from the unit.
Don’t extract the USB device while operating.
Music files (MP3/WMA), image files (JPEG) and Video files can
be played.
This unit cannot use a USB HUB.
Recommended Memory Cards.
Compact Flash Card (CFC), Micro Drive (MD), Smart Media Card
(SMC), Memory Stick (MS), Secure Digital Card (SD), Multimedia
Card (MMC), Memory Stick Pro (MS-Pro)
- Compatible with: FAT16, FAT32
- Only use the memory cards recommended.
Devices which require additional program installation when you
have connected the unit to a computer are not supported.
In case of a USB HDD, make sure to connect an auxiliary power
cord to the USB HDD for proper operation. Up to 2 primary
partitions of a drive are supported. If there is an extension
partition, up to four partitions are supported.
If the drive of USB device is two or more, a drive folder is
displayed on the screen. If you want to move to the initial menu
after you select a folder, press RETURN.
Digital cameras and mobile phones are not supported.
Only USB 1.0/ 1.1supported.(In case USB 2.0 is inserted in to the
player,if operates at the same speed as that of USB 1.1.)
11. PORT. IN Jack
Using PORTABLE device
When you connect a portable music playing device to the PORT.
IN jack on this device by using a ( 3.5mm)mini stereo cable
(not supplied), you can here the sound being outputted from the
portable device through the speaker
For manual tuning, press TUNING (-/+) repeatedly.
For automatic tuning, press and hold TUNING (-/+) for about
two seconds on the front panel.
9. VOLUME controller Adjusts speaker volume.
12. STOP
Operate using the Remote Control
1. POWER
2. MUTE Press MUTE to mute your unit. You can mute your
unit in order, for example, to answer the telephone.
1
2
4
3
5
6
7
8
3. • FUNCTION : (DVD/CD → FM)
• INPUT : (USB → AUX → TV-- AUDIO → PORTABLE )
4. SLEEP You can set the DVD/CD Receiver to turn off automatically
at a specified time.
1. Press SLEEP to set the desired sleep time. The sleep time
appears in the display window.
2. Each time you press SLEEP the setting changes in the
following order.
(DIMMER ON)→SLEEP 180 →150 →120→90 →80 → 70 → 60→ 50 → 40 →
30 → 20 →10 →(DIMMER OFF)
Note: You can check the remaining time before the DVD/CD Receiver
turns off.
Press SLEEP. The remaining time appears in the display window.
5. RETURN Removes the setup menu.
6. 0-9 numerical buttons Selects a service, program number
directly or selects numbered options in a menu.
6
FUNCTION
INPUT
SLEEP
RETURN
EQ
VSM
13. b/B/v/V (left/right/up/down)Selects an option in the
menu.
11
9
13
10
12
14
15
16
18
17
19
20
REPEAT
REPEA
S-TITLE
RDS
preset station you want.
Each time you press the button, the DVD/CD Receiver tunes in
one preset station at a time.
Preset radio stations in the DVD/CD Receiver’s memory first
(see “Presetting radio stations”)
TUN.(-/+) (b/B) For manual tuning, press TUN (-/+)
repeatedly.
For automatic tuning, press and hold TUN. (-/+) for about two
seconds on the front panel.
14. SCAN(bb/BB) During playback, press SCAN (m or
M) repeatedly to select the required scan speed.
DVD,DivX : bb, bbb, bbbb, bbbbb,or BB, BBB,
BBBB, BBBBB
WMA/MP3, Audio CD : m(X2, X4, X8) or M(X2, X4, X8)
SLOW(bb/BB) In the pause mode, press SLOW
(m or M) to select required speed.
DVD : t (1/2, 1/4, 1/8, 1/16) or T (1/2, 1/4, 1/8, 1/16)
DivX : T (1/2, 1/4, 1/8, 1/16)
PTY
22
21
CLEAR
23
24
15.
7. EQ (EQUALIZER Effect)
You can choose 7 fixed sound impressions.Each time you press the
button the setting changes in the display window as shown below.
• AUTO EQ : AUTO EQ operates only in the MP3 files which
include the Tag information in the DVD or USB function.
( ID3 Tag is operated.ver.1 only.)
- WMA file operates to Normal EQ regardless of Tag information.
NORMAL → NATURAL →(AUTO EQ )→ POP → CLASSIC → ROCK
→ JAZZ → NORMAL..
8. VSM Press VSM to set the VIRTUAL sound.
You can enjoy surround sound simply by selecting one of the
pre-programmed sound fields according to the program you want
to listen to . Press VSM button repeatedly.
- 2 Ch Source : BYPASS →VIRTUAL → ON STAGE →PLII
MOVIE → PLII MUSIC → PLII MTRX→ BYPASS...
- 5.1Ch Source: BYPASS →VIRTUAL → BYPASS
9. SETUP Accesses or removes setup menu
10. MENU Accesses the menu on a DVD disc.
11. DISPLAY
1. Press DISPLAY to show various information about the disc
loaded on-screen.The displayed items differ depending on
the disc type or playing status.
2. You can select an item by pressing v / V and change or
select the setting by pressing b / B.
12. TITLE If the current DVD title has a menu, the title menu
appears on the screen. Otherwise, the disc menu may
appear.
• Title (Track) –Current title (or track) number/total number of
titles (or tracks).
• Chapter –Current chapter number/ total number of chapters.
• Time – Elapsed playing time.
• Audio – Selected audio language or channel.
• Subtitle – Selected subtitle.
• Angle – Selected angle/ total number of angles.
• Sound – Selected sound mode.
Note: If a button is not pressed for a few seconds, the onscreen display disappears.
. / >)During playback, press SKIP (.
SKIP (.
or >) to go to the next chapter/track or to return to the
beginning of the current chapter/track. Press SKIP .
twice briefly to step back to the previous chapter/track.
16. VOLUME (+/-) Adjusts speaker volume.
17. • PLAY(B) - To Play disc and file
- 1.5 speed playback DVD MP3 WMA ACD
You can quickly enjoy a movie and music.
The 1.5 speed allows you to watch the pictures and listen to the
sound quicker than playing at a normal speed on the disc.
1. Press the PLAY button during the normal playback. The
screen will appear at 1.5 speed with sound .
2. To return to normal PLAY, press PLAY.
- FM mode state,selects MONO or STEREO by pressing
on the remote control PLAY button.
• PAUSE/STEP (X) During playback, press X to pause
playback. ALL
Press X repeatedly to play Frame-by-Frame.
DVD
DivX
x)
• STOP (x
18. PROG./MEMO. Accesses or removes Program menu.
Enter a radio station’s frequency into the tuner.
19. REC (z) - USB Direct Record
This function enable you to record music to a connected
USB storage device from AUDIO CD.
Before USB recordings, read the notes on the page 14.
1.Insert a USB device suffiicent free space to the USB port on
the unit.
2.Select DVD/CD to record from by pressing FUNCTION button
on the remote control.
AUDIO CD - Press v / V to select the track/file you want
3. Press REC (z) on the remote control to start record.
“USB REC” will start flashing on the display.
- When you start the USB recording ,Recording percentage rate
will be appear on the display window during the recording .
4. File will be stored to CD_REC in a format “TRK_001.mp3”
5. To stop the recording press STOP.
7
ENGLISH
ENTER Acknowledges the menu selection.
PRESET(v/V) Press PRESET +/- repeatedly to select the
Record AUDIO CD source to USB
One track recording : If the usb recording is played during
playback of the cd, the only track would be recording into the
USB.
All track recording: If the USB Rec. button is pressed at the
CD stop, all track would be recording.
Program list recording: USB Records after selectig the tracks
pressing the PROG./MEMO. button if you want to record the
tracks you want.
20. SUBTITLE
DVD
DivX
During playback ,S-TITLE repeatedly to select a desired
subtitle language.
21. REPEAT During playback, press REPEAT repeatedly to
select a desired repeat mode.
DVD Video discs: Chapter/Title/Off
Audio CD, DivX/MP3/WMA discs: Track/All/Off
22. RDS/ PTY Views the various displays of the RDS options.
23. CLEAR Removes a track number on the program menu.
24. TV - Controlling the TV
Your remote control is capable of operating your DVD/CD
Receiver as well as limited functions of LG TV.
Follow the instructions below to operate your LG TV.
Setting Remote Control Codes for LG TV
1.Hold POWER (TV) and press CHANNEL(v/V) button
repeatedly until the TV on or off.
2.The POWER (TV), CHANNEL(v/V), VOLUME (+/-), and INPUT
buttons on remote control are used to operate the LG TV.
Note: If the remote control does not operate your particular TV,
try the other code or use the remote control originally supplied
with the LG TV. (LG and Gold Star)Due to the variety of codes
used by manufacturers, OUR COMPANY cannot guarantee that
the remote control will operate every LG TV model.
Setup
Initial Settings
By using the Setup menu, you can make various adjustments to
items such as picture and sound. You can also set a language
for the subtitles and the Setup menu, among other things. For
details on each Setup menu item, see the pages 8 to 9.
a
b
c
d
e
a LANGUAGE - Menu Language/ Disc Audio /
Subtitle / Menu
b DISPLAY - TV Aspect / Display Mode / Progressive Scan
/ TV output select
c AUDIO - 5.1 Speaker Setup/ Dynamic Range Control
(DRC)/ Vocal
d LOCK (Parental Control) - Rating / Password / Area Code
e OTHERS - DivX(R) VOD / REC Bitrate
To display and exit the Menu:Press SETUP to display the
menu. A second press of SETUP will take you back to initial
screen.
To go to the next level: Press B on the Remote Control.
To go back to the previous level:Press b on the Remote
Control.
GENERAL OPERATION
1. Press SETUP. The Setup menu appears.
2. Use v / V to select the desired option then press B to move
to the second level. The screen shows the current setting for
the selected item, as well as alternate setting(s).
3. Use v / V to select the second desired option and then press
B to move to the third level.
4. Use v / V to select the desired setting then press ENTER to
confirm your selection. Some items require additional steps.
5. Press SETUP or PLAY to exit the Setup menu.
Original – Refers to the original language in which the disc was
recorded.
Other – To select another language, press numeric buttons and
then ENTER to enter the corresponding 4-digit number
according to the language code list on the page 12. If you enter
the wrong language code, press CLEAR.
DISPLAY
TV Aspect
4:3 – Select when a standard 4:3 TV is connected.
16:9 – Select when a 16:9 wide TV is connected.
Display Mode: The display Mode setting works only when the
TV Aspect mode is set to “4:3”.
Letterbox – Displays a wide picture with bands on the upper
and lower portions of the screen.
Panscan – Automatically displays the wide picture on the entire
screen and cuts off the portions that do not fit.
Progressive Scan
Progressive Scan Video provides the high quality pictures with
less flickering. If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set [Progressive Scan] to [On]. Press
ENTER.
- If you not press ENTER within 10 seconds it will be [OFF].
- If you have no progressive scan TV ,in the state progressive
scan [on] will not appear the screen.
(so then,press and hold STOP button on the remote control
5seconds. it will be change [OFF].)
TV Output Select – Select an option according to the TV
connection type. [YPbPr]: When your TV is connected with the
COMPONENT/PROGRESSIVE SCAN jacks on the unit. [RGB]:
When your TV is connected with the SCART jack.
- When connected by RGB, COMPONENT OUT not operate.
- In Progressive scan [on] state, TV Output select mode is
inactivate.
AUDIO
Each DVD disc has a variety of audio output options. Set the
receiver’s AUDIO options according to the type of audio system
you use.
LANGUAGE
5.1 Speaker Setup
Menu Language: Select a language for the Setup menu and the
on-screen display.
Disc Audio / Subtitle / Menu:
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Make the following settings for the built-in 5.1 channel surround
decoder.
8
1. Press ENTER and 5.1 Speaker Setup menu appears.
2. Use b / B to select the desired speaker.
Speaker selection
Select a speaker that you want to adjust. [Front speaker (Front
L), Front speaker (Front R), Center Speaker (Center), Subwoofer
(SubWoofer), Rear speaker (Rear L), Rear speaker (Rear R)]
Note: Certain speaker settings are prohibited by the Dolby
Digital licensing agreement.
Size: Since the speaker settings are fixed, you cannot change
the settings.
Volume: Press b / B to adjust the output level of the selected
speaker. (-6dB ~ 6dB)
If you forget your password
If you forget your password, you can clear it using the following
steps:
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number “210499” and press
ENTER. The password is cleared.
Area Code
Enter the code of the area whose standards were used to rate
the DVD video disc, based on the list on page 12.
1. Select “Area Code” on the LOCK menu then
press B.
2. Follow step 2 as shown in rating section.
3. Select the first character using v / V buttons.
Distance: If you connected speakers to your DVD/CD Receiver,
setting the Distance lets the speakers know how far the sound
has to travel to reach your set listening point. This allows the
sound from each speaker to reach the listener at the same time.
5. Press ENTER to confirm your Area code selection.
Press b / B to adjust the Distance of the selected speaker.
OTHERS
Test : Press b / B to test the signals of each speaker. Adjust the
volume to match the volume of test signals memorized in the
system.
DivX(R) VOD Registration
Front Left (L) → Center → Front Right (R) → Rear Right (R)
→ Rear Left (L) → SubWoofer
DRC (Dynamic Range Control)
Make the sound clear when the volume is turned down (Dolby
Digital only). Set to [On] for this effect.
Vocal
Set Vocal to [On] only when a multi-channel karaoke DVD is
playing. The karaoke channels on the disc will mix into normal
stereo sound.
LOCK (Parental Control)
Rating: Blocks playback of rated DVDs based on their
ENGLISH
3. Adjust options using v / V / b / B buttons.
4. After setting, returns to the previous menu by pressing
RETURN button.
4. Press B and select the second character using
v / V buttons.
We provide you the DivX® VOD (Video On Demand) registration
code that allows you to rent and purchase videos based on the
DivX® VOD service. For more information, visit
www.divx.com/vod.
1. Select “DivX(R) VOD” option and then press B.
2. Press ENTER while “Select” is selected and the registration
code will appear.
Use the registration code to purchase or rent the videos from
DivX® VOD service at www.divx.com/vod. Follow the
instructions and download the video onto a disc for playback
on this unit.
3. Press ENTER to exit.
Note: All the downloaded videos from DivX® VOD can only be
played back on this unit.
REC Bitrate : Set USB record Bitrate to 96kbps or 128kbps (see
page 8)
contents. Not all discs are rated.
1. Select “Rating” on the LOCK menu then press B.
2. To access the LOCK options, you must input the password
you have created. If you have not yet entered password, you
are prompted to do so.
Input a password and press ENTER. Enter it again and press
ENTER to verify. If you make a mistake before pressing
ENTER, press CLEAR.
3. Select a rating from 1 to 8 using the v / V buttons.
Rating 1-8: Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
Unlock: If you select unlock, parental control is not active
and the disc plays in full.
4. Press ENTER to confirm your rating selection, then press
SETUP to exit the menu.
Password: You can enter or change password.
1. Select Password on the LOCK menu and then press B.
2. Follow the step 2 as shown above (Rating).
To change the password, press ENTER when the “Change”
option is highlighted. Input a password and press ENTER.
Enter it again and press ENTER to verify.
3. Press SETUP to exit the menu.
9
Presetting the Radio Stations
You can preset 50 stations for FM Before tuning, make sure that
you have turned down the volume.
1. Press FUNCTION on the Remote Control until FM appears
in the display window.
2. Press and hold TUN.(-/+) for about two seconds until the
frequency indication starts to change, then release.
Scanning stops when the DVD/CD Receiver tunes in a
station.
3. Press PROG./MEMO. on the Remote Control.
A preset number will flash in the display window.
4. Press PRESET +/- on the Remote Control to select the
preset number you want.
5. Press PROG./MEMO. on the Remote Control again.
The station is stored.
6. Repeat steps 3 to 6 to store other stations.
To tune in a station with a weak signal
Press TUN.(-/+) repeatedly in step 3 to tune in the station
manually.
To clear all the stored stations
Press and hold PROG./MEMO. for about two seconds and “
ERASE ALL” appears in the display window and then press
PROG./MEMO. again, the stations are cleared.
If you have accidentally entered into the "ERASE ALL" mode
and you do not wish to clear the memory, do not press any
key. After a few seconds, the "ERASE ALL" will go off by itself
and change to normal mode.
Note: If all stations have already been entered, the FULL
message will appear in the display window for a moment and
then a preset number will flash. To change the preset number,
follow steps 5-6 as above.
Playing an Audio CD or MP3/WMA/JPEG/ DivX file
Playing an Audio CD or MP3/WMA file
This unit can play Audio CDs or MP3/WMA files.
MP3/ WMA/ Audio CD
Once you insert a cd with MP3/WMA files or Audio, a menu
appears on the TV screen.
Press v / V to select a track/file and then press PLAY or
ENTER, and playback starts. You can use variable playback
functions. Refer to the page 6,7or 8.
ID3 TAG
When playing a file containing information such as track titles,
you can see the information by pressing DISPLAY.
[ Song,Title, Artist, Album, Year, Comment ]
-ID3 Tag will be operate in the MP3 file.
Tips:
Press MENU to move to the next page.
On a CD with MP3/WMA and JPEG, you can switch
MP3/WMA and JPEG. Press TITLE, and MUSIC or PHOTO
top of the menu is highlighted.
AUTO EQ is set for WMA/ MP3 file in the DVD/CD,USB
function.
2. Press REPEAT to select a desired repeat mode.
• TRACK: repeats the current track
• ALL: repeats all the tracks on programmed list.
• Off(No display): does not play repeatedly.
Erasing a Track from “Program” List
1. Use v V to select the track that you wish to erase from the
Program list.
2. Press CLEAR. Repeat to erase additional tracks on the list.
Erasing the Complete Program List
Press PROG./MEMO. and then, “
” icon will appear.
Use v / V to select “ Clear All” icon and then press ENTER.
Note:
- The programs are also cleared when the disc is removed.
- During playback,AUTO skip is not supported
Viewing a JPEG file
This unit can play discs with JPEG files.
Before playing JPEG recordings, read the notes on JPEG
Recordings page 14.
Programmed Playback
1. Insert a disc and close the tray.
The PHOTO menu appears on the TV screen.
The program function enables you to store your favorite tracks
from any disc in the receiver memory. A program can contain 30
tracks.
1. Insert a disc. Audio CD and MP3/WMA Discs:
2. Press v / V to select a folder, and then press ENTER. A list
of files in the folder appears. If you are in a file list and want
to return to the previous Folder list, use the v / V buttons on
the Remote to highlight
and press ENTER.
2. Select a track on the “List”, and then press
PROG./MEMO.“
” icon appears on the display window
and then press ENTER to place the selected track on the
“Program” list. Repeat to place additional tracks on the list.
3. If you want to view a particular file, press v / V to highlight a
file and press ENTER or PLAY. While viewing a file, you can
press STOP to move to the previous menu (JPEG menu).
3. Select the track you want to start playing on the “Program” list.
Press MENU to move to the next page.
4. Press PLAY or ENTER to start. Playback begins in the order
in which you programmed the tracks. Playback stops after all
of the tracks on the “Program” list have played once.
5. To resume normal playback from programmed playback,
select a track of AUDIO CD (or MP3/WMA) list and then
press PLAY.
Repeat Programmed Tracks
1. Press REPEAT when playing a disc. The repeat icon
appears.
10
Tips:
There are three Slide Speed options
: > (Slow), >>
(Normal), >>> (Fast) .Use v /V /b /B to highlight the Speed.
Then, use b / B to select the option you want to use and then
press ENTER.
Slide Show : Use v V b B to highlight the
(Slide Show)
then press ENTER.
Still Picture :
1.Press PAUSE/STEP during the slide show. The DVD/CD
Receiver will now go into the PAUSE mode.
2.To return to the slide show, press PLAY or press PAUSE/STEP
again.
Moving to another File
Press SKIP (. or >) once during viewing a picture to
advance to the next or previous file.
Rotating the picture
Press v /V during showing a picture to rotate the picture
clockwise or counter-clockwise.
Playing a DivX Movie file
You can play DivX file in USB device and DivX disc. in the
DVD/CD Receiver
1. Insert a disc and close the tray. The MOVIE menu appears
on the TV screen.
2. Press v / V to select a folder and then press ENTER. A list
of files in the folder appears. If you are in a file list and want
to return to the Folder list, use the v / V buttons on the
remote to highlight
and press ENTER.
3. If you want to view a particular file, press
v / V to highlight a file and press ENTER or PLAY.
4. Press STOP to exit.
Tips:
Press MENU to move to the next page.
On a CD with MP3/WMA, JPEG and MOVIE file, you can
switch MUSIC, PHOTO and MOVIE menu. Press TITLE and
MUSIC, PHOTO and MOVIE word on top of the menu is
highlighted.
Notes:
Be sure to select “SUBTITLE ON” mode by pressing the
subtitle file every time before playing a DivX file .
When the subtile has more than two languages in the file,
original subtile is only available.
You can not adjust sound mode and VIRTUAL sound
[VSM]during the DivX file playing.
Notice for displaying the Divx subtitle
If the subtitle does not display properly during playback, press and
hold S-TITLE for about 3 seconds then press S-TITLE to select
another language code until the subtitle is displayed properly
Additional features
Time Search DVD DivX
To start playing at any chosen time on the disc:
1.Press DISPLAY during playback.
2.Press v / V to select the time clock icon and
“--:--:--” appears.
3.Input the required start time in hours, minutes, and seconds
from left to right. If you enter the wrong numbers, press
CLEAR to remove the numbers you entered. Then input the
correct numbers.
4.Press ENTER to confirm. Playback starts from the selected
time.
Screen Saver The screen saver appears when you leave the
unit in Stop mode for about five minutes.
Last Scene Memory DVD ACD
This receiver memorizes the last scene from the last disc that is
viewed. The last scene remains in the memory even if you
remove the disc from the receiver or switch off the receiver.
If you load a disc that has the scene memorized, the scene is
automatically recalled.
Note: This receiver does not memorize the scene of a disc if
you switch off the receiver before commencing to play the disc.
System Select
You must select an appropriate system mode for your TV
system. If NO DISC appears in the display window, press and
hold PAUSE/STEP on theremote control for more than 5
seconds to be able to select a system (PAL, NTSC or AUTO).
When the selected system is not compatible with the system
of your TV, normal colour picture may not be displayed.
NTSC: Select when DVD/CD Receiver is connected with NTSCTV.
PAL: Select when DVD/CD Receiver is connected with PALTV.
AUTO: Select when DVD/CD Receiver is connected with Multi
system TV.
RDS Operation
This unit is equipped with RDS (Radio Data System), which
brings a wide range of information to FM radio. RDS, now being
used in many countries, is a system for transmitting station call
signs.
RDS TUNING
When a FM station is tuned in and it contains RDS data, the unit
will automatically display the station call signs.
1. Press FUNCTION to select the FM mode.
2. Select a desired station by pressing TUN.(-/+).
When the RDS transmission is received, the display shows
the program serive name (PS).
Note:
Some RDS stations may not choose to include some of these
additional features. If the data required for the selected mode is
not being transmitted, the Display Window will show a PS
NONE,RT NONE,CT NONE, or PTY NONE message.
Programme Search (PTY)
You may search for a specific Programme Type (PTY) by
following these steps:
1. Press FUNCTION to select the FM mode on the remote
control.
3. Press RDS to recall the frequency.
2. Press PTY on the remote control, the display will show the
last PTY in use.
RDS DISPLAY OPTIONS
3. Press PTY repeatedly to select a desired PTY.
The RDS system is capable of transmitting a wide variety of
information in addition to the initial call sign that appears when a
station is first tuned. In normal RDS operation the display will
indicate the station name, broadcast network or call letters.
Pressing RDS on the remote control enables you to cycle
through the various data types in the sequence:
4. When the PTY is selected, press TUN.(-/+).The unit will go
into an automatic search mode.When a station is tuned, the
search will stop.
(PS → FREQUENCY → PTY → RT → CT)
11
ENGLISH
Listening to the music during slide show :
You can listen to music during slide show, if the disc contain
music and photo files together. Use v /V /b /B to highlight
icon then press ENTER to start slide show.
You can not adjust sound mode and VIRTUAL sound
[VSM]during the Music PHOTO ALBUM playing.
Reference
Language Codes
Use this list to input your desired language for the following initial settings: Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Area Codes
Area
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
12
Language
Fiji
Finnish
French
Frisian
Galician
Georgian
German
Greek
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian
Icelandic
Indonesian
Interlingua
Irish
Italian
Japanese
Javanese
Kannada
Kashmiri
Kazakh
Kirghiz
Korean
Kurdish
Laothian
Latin
Latvian, Lettish
Code
7074
7073
7082
7089
7176
7565
6869
6976
7576
7178
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Choose a area code from this list.
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
Area
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Greenland
Code
ET
FJ
FI
FR
DE
GB
GR
GL
Heard and McDonald Islands HM
Hong Kong
HK
Hungary
HU
India
IN
Indonesia
ID
Israel
IL
Italy
IT
Jamaica
JM
Japan
JP
Kenya
KE
Kuwait
KW
Libya
LY
Luxembourg
LU
Area
Malaysia
Maldives
Mexico
Monaco
Mongolia
Morocco
Nepal
Netherlands
Netherlands Antilles
New Zealand
Nigeria
Norway
Oman
Pakistan
Panama
Paraguay
Philippines
Poland
Portugal
Romania
Russian Federation
Code
MY
MV
MX
MC
MN
MA
NP
NL
AN
NZ
NG
NO
OM
PK
PA
PY
PH
PL
PT
RO
RU
Area
Saudi Arabia
Senegal
Singapore
Slovak Republic
Slovenia
South Africa
South Korea
Spain
Sri Lanka
Sweden
Switzerland
Taiwan
Thailand
Turkey
Uganda
Ukraine
United States
Uruguay
Uzbekistan
Vietnam
Zimbabwe
Code
SA
SN
SG
SK
SI
ZA
KR
ES
LK
SE
CH
TW
TH
TR
UG
UA
US
UY
UZ
VN
ZW
Troubleshooting
Symptom
No power.
Cause
• The power cord is disconnected.
• The video cable is not connected
securely.
• The connected TV power is turned off.
• The equipment connected with the
audio cable is not set to receive DVD
signal output.
• The audio cables are not connected
securely.
• The power of the equipment connected
with the audio cable is turned off.
• The audio connecting cable is damaged.
Correction
• Plug the power cord securely into the
wall outlet.
• Insert a disc. (Check that the DVD or,
audio CD indicator in the DVD display
is lit.)
• Select the appropriate video input
mode on the TV so the picture from
the DVD/CD Receiver appears on the
TV screen.
• Connect the video cable into the
jacks securely.
• Turn on the TV.
• Select the correct input mode of the
audio receiver so you can hear the
sound from the DVD/CD Receiver.
• Connect the audio cable into the
jacks securely.
• Turn on the equipment connected
with the audio cable.
• Replace it with new one.
• The disc is dirty.
• Clean the disc.
The power is on, but
the DVD/CD Receiver
does not work.
• No disc is inserted.
No picture.
• The TV is not set to receive DVD signal
output.
There is no sound or
only a very low-level
sound is heard.
The playback picture is poor.
The DVD/CD Receiver • No disc is inserted.
does not start playback.
• An unplayable disc is inserted.
• The disc is placed upside down.
• The disc is not placed within the guide.
• The disc is dirty.
• A menu is on the TV screen.
• The Rating level is set.
Loud hum or noise is
heard.
Radio stations cannot
be tuned in.
The remote control
does not work properly.
The front panel display
is too dim.
• The disc is dirty.
• The speakers and components are
connected poorly.
• The DVD/CD Receiver is located too
close to the TV.
• The antenna is positioned or connected
poorly.
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning).
• No stations have been preset or preset
stations have been cleared (when
tuning by scanning preset stations).
• The remote control is not pointed at the
remote sensor of the DVD/CD Receiver.
• The remote control is too far from the
DVD/CD Receiver.
• There is an obstacle in the path of the
remote control and the DVD/CD
Receiver.
• The batteries in the remote control are
flat.
• Nothing is displayed on the front panel
display.
ENGLISH
Check the following guide for the possible cause of a problem before contacting service.
• Insert a disc. (Check that the DVD, or
audio CD indicator in the DVD display
is lit.)
• Insert a playable disc. (Check the
disc type, colour system and Regional
code.)
• Place the disc with the playback side
down.
• Place the disc on the disc tray
correctly inside the guide.
• Clean the disc.
• Press the SETUP button to turn off
the menu screen.
• Cancel the Rating function or change
the rating level.
• Clean the disc.
• Connect the speakers and
components securely.
• Move your TV away from the audio
components.
• Connect the antenna securely.
• Adjust the antennas and connect an
external antenna if necessary.
• Tune in the station manually.
• Preset the stations (page 10).
• Point the remote control at the remote
sensor of the DVD/CD Receiver.
• Use the remote control within about
23 ft (7 m).
• Remove the obstacle.
• Replace the batteries with new ones.
• Press SLEEP(Dimmer) on the remote
control.
13
MP3 / WMA disc compatibility with this player is limited as
follows:
• Sampling frequency: within 8 - 48 kHz (MP3),
within 22.05 - 48kHz (WMA)
• Bit rate: within 8 - 320kbps (MP3), 32 - 256kbps (WMA)
Support Ver : v2 , v7, v8, v9
• File extensions: “.mp3” / “.wma”
• CD-ROM file format: ISO9660
• We recommend that you use Easy-CD Creator, which creates
an ISO 9660 file system.
• The total number of characters for file name: maximum 8
characters (excluding file extensions like mp3/wma)
• They should not contain special letters such as / ? * : “ < > l
etc.
• The total number of files on the disc should be less than 650.
• This player can not support files with such as extention s as
bmp,zip..
• In case of spec.out file will be skip to the next file
automatically,while playing of file in order.
Customers should note that permission is required in order
to download MP3 / WMA files and music from the Internet.
Our company has no right to grant such permission.
Permission should always be sought from the copyright
owner.
JPEG disc compatibility with this player is limited as
follows:
• Normal JPEG - Max pixel in width : 8902 pixel
• Progressive JPEG - Max pixel in width : 1609 pixel
• Maximum files : Under 650.
• Some discs may not operate due to a different recording
format or the condition of disc.
• File extensions: “.jpg”
DivX disc compatibility with this player is limited as
follows:
• Available resolution: within 720x576 (W x H) pixels
• The file name of the DivX subtitle is available by 45
characters.
• If there is impossible code to express in the DivX file, it may
be displayed as " _ " mark on the display.
• Frame rate : less than 30 fps
• If the video and audio structure of recorded files is not
interleaved, either video or audio is outputted.
• Playable DivX file: ".avi ", ".mpg ", ".mpeg ", ".divx"
• Playable Subtitle format: SubRip(*.srt/*.txt), SAMI(*.smi),
SubStation Alpha(*.ssa/*.txt), MicroDVD(*.sub/*.txt),
SubViewer 2.0(*.sub/*.txt), VobSub(*.sub)
• Playable Codec format: DIVX3.xx ", "DIVX4.xx ", "DIVX5.xx
", "MP43 ", "3IVX ".
• Playable Audio format: "AC3 ", "DTS ", "PCM ", "MP3 ",
"WMA ".
• Sampling frequency: within 32 - 48 kHz (MP3),
within 24 - 48kHz (WMA)
• Bit rate: within 32 - 320kbps (MP3), 40 - 192kbps (WMA)
• Max bitrate : USB: 4Mbps , CD: 4Mbps, DVD: 7Mbps
• For Discs formatted in Live file system ,you can not it on this
player.
• If the name of movie file is different from that of the subtitle
file,during playback of a DivX file, subtitle may not be display.
• If you play a DivX file differ from DivXspec ,it may not operate
normally.
USB Recording with this player is limited as follow notes:
Note:- When you stop recording during playback ,the file that
has been recorded at that time will be stored.
- External HDD, Multi Card reader ,Locked device and MP3
player is not supported.
- If you record more 648 files on CD_REC folder appears
“ERROR” on the display.
- In the state SACD,CD-G ,DTS disc USB Record is not
operated.
- During USB recording, is no sound of music and some keys
except for POWER, STOP and SLEEP key not operate.
- When you extract the device or power off while recording,
stored MP3 file can not playback or not may be formed a file.
- USB recording time can be difference according to the writing
speed of device
- During the record ,can not change any function and volume.
- When you press the Rec button on the remote control in all
function appointed sound mode return to BYPASS
- USB port of the unit can not be connected to PC. The unit can
not be used as a storage device.
- USB record is available to within 20hz~ 16khz.
Specifications
General
Power supply
Refer to the back panel of the unit.
Power consumption
Refer to the back panel of the unit.
Net Weight
2.5 kg
External dimensions (WxHxD)
360 x 62 x 305 mm
Operating conditions
Temperature: 5°C to 35°C, Operation status: Horizontal
Operating humidity
5% to 85%
Amplifier
Output Power
Front: 45 W + 45 W (Rated Output Power 30 W, THD 10 %)
Centre*: 45 W
Surround*: 45 W + 45 W (Rated Output Power 30 W, 4 Ω at 1 kHz, THD 10 %)
Subwoofer*: 75 W (Rated Output Power 60 W, 8 Ω at 30 Hz, THD 10 %)
Speakers
SH33SD-S
SH33SD-W
Impedance
4Ω
8Ω
Net Dimensions (WxHxD)
99 x 114 x 86 mm
156 x 325 x 320 mm
Net Weight (1EA)
0.35 kg
3.5 kg
Designs and specifications are subject to change without notice.
14
Technology with the human touch
GUARANTEE
● LG Electronics U.K. Ltd. will provide the following services in order to expedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a period of
12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the
repair of this LG equipment, for a period of 12 months from the original date of purchase. These claims
must be made in accordance with the published scale of service charges and
relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made to the
apparatus, or if non standard components are used or if the serial number of the
apparatus is removed, defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was originally
purchased. The dealer may, before carrying out service under guarantee, require a receipted account as
evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become exhausted or
worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
● REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE
SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED.
● Product Registration Card :
It is helpful to complete at least your name, address, phone, model & serial
numbers and return it. This will enable LG to assist you in the future should you
lose your receipt, your units be stolen, or should modifications be necessary.
● To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm
*
Please complete for your own record
MODEL NO.*
SERIAL NO.*
DATE OF PURCHASE.*
In all cases of difficulty - consult your LG dealer
from whom the product was purchased
Download PDF