LG | HT806PH | LG HT806PH Owner’s Manual

OWNER’S MANUAL
DVD Home Theater
System
Please read this manual carefully before operating
your set and retain it for future reference.
FOR THE WARRANTY TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL.
HT806PH (HT806PH, SH86TH-S/ C, SH86SH-S, SH95TA-W)
P/NO : MFL67084756
HT806PH-D0_BGBRLL_ENG_4756.indd 1
2011-02-15 �� 10:10:49
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
HT806PH-D0_BGBRLL_ENG_4756.indd 2
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
2011-02-15 �� 10:10:49
Getting Started
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted
material without permission. This product features the
copy protection function developed by Macrovision.
Copy protection signals are recorded on some
discs. When recording and playing the pictures of
these discs picture noise will appear. This product
incorporates copyright protection technology that
is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection
technology must be authorized by Macrovision, and
is intended for home and other limited viewing uses
only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE
WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS
TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS REGARDING
OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
AND 625p UNIT, PLEASE CONTACT OUR CUSTOMER
SERVICE CENTER.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot use
it on LG players.
(Mastered/ Live File System : Disc format system for
Windows Vista)
Disposal of your old appliance
1. W
hen this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/EC.
2. A
ll electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or
the local authorities.
3. T he correct disposal of your
old appliance will help prevent
potential negative consequences
for the environment and human
health.
HT806PH-D0_BGBRLL_ENG_4756.indd 3
4. F or more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.
1
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive
2004/108/EC, 2006/95/EC, and
2009/125/EC.
Getting Started
Copyrights
3
European representative :
LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere, The
Netherlands (Tel : +31–(0)36–547–8888)
POWER: This unit operates on a mains supply of
200-240V~, 50/60Hz.
WIRING: This unit is supplied with a BSI 1363
approved 13 amp mains plug, fused at 5 amp.
When replacing the fuse always use a 5 amp BS
1362, BSI or ASTA approved type. Never use this
plug with the fuse cover omitted. To obtain a
replacement fuse cover contact your dealer. If the
type of plug supplied is not suitable for the mains
sockets in your home, then the plug should be
removed and a suitable type fitted. Please refer to
the wiring instructions below:
WIRING: A mains plug removed from the mains
lead of this unit must be destroyed. A mains plug
with bared wires is hazardous if inserted in a
mains socket. Do not connect either wire to the
earth pin, marked with the letter E or with the
earth symbol or coloured green or green and
yellow. If any other plug is fitted, use a 5 amp fuse,
either in the plug, or at the distribution board.
IMPORTANT: The wires in this mains lead are
coloured in accordance with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours
of the wires in the mains lead of this unit may not
correspond with the coloured marking identifying
the terminals in your plug, proceed as follows: The
wire which is coloured blue must be connected
to the terminal which is marked with the letter
N or coloured black. The wire which is coloured
brown must be connected to the terminal which
is marked with the letter L or coloured red.
2011-02-15 �� 10:10:49
4
Table of Contents
Table of Contents
1
Getting Started
2
6
6
6
6
6
6
7
7
7
7
7
8
9
10
11
Safety Information
Unique Features
– Portable In
– USB Direct Recording
– Full HD up-scaling
– Home Theater Speaker ez Setup
Accessories
Introduction
– Playable Discs
– About the “&” Symbol Display
– Symbols Used in this Manual
– Regional Codes
Playable file Requirement
Remote control
Front panel
Rear panel
2 Connecting
12
Assembling the speaker stand to the
speaker
13 Attaching the speakers to the unit
14 Positioning the system
15 Connections to Your TV
15 – Component Video Connection
16 – HDMI Out Connection
17 – Video Connection
17 – SCART Connection
18 – Resolution Setting
18 Video Output Resolution
19 Optional Equipment Connection
19 – AUX In Connection
19 – AUDIO (PORT. IN) In Connection
19 – Listening to music from your portable
player or external device
20 – USB Connection
21 – OPTICAL In connection
21 – Home theater speaker ez setup
21 Antenna Connection
HT806PH-D0_BGBRLL_ENG_4756.indd 4
3 System Setting
22 Adjust the setup settings
22 – OSD Initial language settings Optional
22 – To display and exit the Setup menu
23 – Language
23 – Display
24 – Audio
25 – Lock (Parental Control)
26 – Others
4 Operating
27
27
28
28
29
29
29
29
29
29
29
30
31
32
32
32
32
32
32
33
33
33
33
33
33
33
34
34
35
35
Using the Home Menu
Basic Operations
Other Operations
– Displaying Disc Information on-screen
– To display the DVD Menu
– To display the DVD title
– 1.5 times speed playback
– Screen Saver
– Starting play from selected time
– Resume playback
– Changing subtitle code page
– Marked Playback
– Viewing a PHOTO file
– Sleep Timer Setting
– Dimmer
– Turn off the sound temporarily
– Last Scene Memory
– System Select - Optional
– Adjust the speaker level settings
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
– Deleting a saved station
– Improving poor FM reception
– Seeing information about a radio
station
Sound adjustment
– Setting the surround mode
Advanced Operations
– Recording to USB
2011-02-15 �� 10:10:49
Table of Contents
5
5 Troubleshooting
36 Troubleshooting
6 Appendix
37
37
37
38
39
40
41
Maintenance
– Handling the Unit
– Notes on Discs
Area Code List
Language code List
Trademarks and Licenses
Specifications
7 Warranty
1
2
3
43 Warranty
4
5
6
7
HT806PH-D0_BGBRLL_ENG_4756.indd 5
2011-02-15 �� 10:10:49
6
Getting Started
Unique Features
1
Portable In
Accessories
Please check and identify the supplied accessories.
Getting Started
Listen to music from your portable device. (MP3,
Notebook, etc)
USB Direct Recording
Records music from CD to your USB device.
Remote control (1)
Battery (1)
FM antenna (1)
Speaker cables (4)
Full HD up-scaling
Views Full HD picture quality with simple setup.
Home Theater Speaker ez
Setup
Listen to sounds from TV, DVD and Digital device
with vivid 5.1 (2.1 or 2.0) ch mode.
HT806PH-D0_BGBRLL_ENG_4756.indd 6
2011-02-15 �� 10:10:50
Getting Started
Introduction
Playable Discs
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm / 12 cm disc)
Video mode and finalized only.
DVD-RW (8 cm / 12 cm disc)
Video mode and finalized only.
DVD+R: Video mode only
Supports the double layer disc also.
DVD+RW (8 cm / 12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
About the “&” Symbol
Display
“&” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specific media.
HT806PH-D0_BGBRLL_ENG_4756.indd 7
Symbols Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
y
Video files contained in the
USB/Disc
u
Audio files contained in the
USB/Disc
i
Photo files
1
Getting Started
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVD±RW/DVD±R or CD-RW/
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc,
or the characteristics of the recording device and
authoring software.
7
,,Note
Indicates special notes and operating features.
,,Tip
Indicates tip and hints for making the task easier.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or “ALL”.
yy Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
yy If you try to play a DVD with a different regional
code from your unit, the message “Check
Regional Code” appears on the TV screen.
2011-02-15 �� 10:10:50
8
Getting Started
Playable file
Requirement
1
Getting Started
MP3/ WMA music file requirement
MP3/ WMA file compatibility with this unit is limited
as follows :
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3), 40 to 192 kbps (WMA)
yy Support Version : v2, v7, v8, v9
yy Maximum files : Under 999
yy File extensions : “.mp3”/ “.wma”
DivX file requirement
DivX file compatibility with this unit is limited as
follows:
yy Available resolution: within 720 x 576 (W x H)
pixels.
yy The file name of the DivX subtitle should be
entered within 45 characters.
yy If there is impossible code to express in the
DivX file, it may be displayed as “ _ “ mark on the
display.
yy Frame rate : less than 30 fps.
yy If the video and audio structure of recorded
files is not interleaved, either video or audio is
outputted.
yy Playable DivX file : “.avi”, “.mpg”, “.mpeg”, “.divx”
yy We recommend that you use Easy-CD Creator,
which creates an ISO9660 file system.
yy Playable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
Photo file requirement
yy Playable Codec format : “DIVX3.xx”, “DIVX4.xx”,
“DIVX5.xx”, “MP4V3”, “3IVX”.
Photo file compatibility with this unit is limited as
follows :
yy Playable Audio format : “AC3”, “PCM”, “MP3”, “WMA”.
yy CD-ROM file format : ISO9660/ JOLIET
yy Max pixel in width : 2 760 x 2 048 pixel
yy Maximum files : Under 999
yy Some discs may not operate due to a different
recording format or the condition of disc.
yy File extensions: “.jpg”
yy CD-ROM file format : ISO9660/ JOLIET
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3), 40 to 192
kbps (WMA)
yy For Discs formatted in Live file system, you can
not it on this unit.
yy If the name of movie file is different from that of
the subtitle file, during playback of a DivX file,
subtitle may not be display.
yy If you play a DivX file differ from DivXspec, it may
not operate normally.
HT806PH-D0_BGBRLL_ENG_4756.indd 8
2011-02-15 �� 10:10:50
Getting Started
9
Remote control
m INFO/DISPLAY: Accesses OnScreen Display.
n HOME: Displays the [Home
Menu].
DISC MENU: Accesses the menu
on a DVD disc.
• • • • • • b • • • • • •
W/S/A/D (up/ down/ left/
right): Used to navigate on-screen
displays.
PRESET +/-: Selects programme
of Radio.
Remove the battery cover on the
rear of the Remote Control, and
insert one (size AAA) battery with
4 and 5 matched correctly.
SPEAKER LEVEL: Sets the sound
level of desired speaker.
SOUND EFFECT: Selects a sound
effect mode.
VOL -/+ (Volume): Adjusts
speaker volume.
OPTICAL: Changes input source
to optical directly.
1
MUTE: Mutes the sound.
• • • • • • e • • • • • •
0-9 numerical buttons: Selects
numbered options in a menu.
h REPEAT: Selects a play
mode. (Repeat/ Random)
TUNING +/-: Tunes in the desired
radio station.
CLEAR: Removes a number when
setting the password.
b ENTER: Acknowledges menu
selection.
Presetting the radio stations.
• • • • • • f • • • • • •
x RETURN: Moves backwards
in the menu or exits the setup
menu.
-- You can control the sound
level, input source, and power
switching of LG TVs as well.
Hold POWER (TV) and press PR/
CH (W/S) button repeatedly
until the TV turns on or off.
TITLE: If the current DVD title has
a menu, the title menu appears
on the screen. Otherwise, the disc
menu may not appear.
Battery Installation
• • • • • • d • • • • • •
Getting Started
SLEEP: Sets the System to turn off
automatically at a specified time.
(Dimmer : The display window will
be darken by half.)
TV Control buttons: Controls the
TV. (LG TV only)
X REC: USB Direct Recording.
• • • • • • c • • • • • •
?: This button is not available.
Z STOP: Stops playback.
RDS : Radio Data System.
d PLAY, MONO/STEREO: Starts
playback. Selects Mono/ Stereo.
PTY : Views the various displays of
the RDS.
M PAUSE/STEP: Pauses playback.
• • • • • • a • • • • • •
C/V SKIP: Goes to the next
or previous chapter / track / file.
P RADIO&INPUT: Changes
input sources.
c/v SCAN: Searches
backward or forward.
MARKER: Marks play list.
1 POWER: Switches the unit ON
or OFF.
B OPEN/CLOSE: Opens and
closes the disc Drawer.
HT806PH-D0_BGBRLL_ENG_4756.indd 9
2011-02-15 �� 10:10:50
10
Getting Started
Front panel
1
Getting Started
a
b cd e f
kj
i
h
g
a 1/! (POWER)
Switches the unit ON or OFF.
g VOLUME
Adjusts speaker volume.
b R (OPEN/CLOSE)
Opens or closes the disc tray.
h Display window
Shows the current status of the unit.
c T (PLAY/PAUSE)
Starts playback.
Pauses playback temporarily, press again to exit
pause mode.
i Disc Tray
d I STOP
Stops playback.
j USB Port
Connects a USB device.
k PORT. IN
Connects to a portable player with audio
outputs.
e Y/U (SKIP)
Goes to next or previous file/track/chapter.
Searches backward or forward (Press and hold)
Tunes in the desired radio station.
f FUNC. (FUNCTION)
Changes the input source or function.
HT806PH-D0_BGBRLL_ENG_4756.indd 10
2011-02-15 �� 10:10:50
Getting Started
11
Rear panel
1
a
b
a Power cord
b Speakers connectors
Connects the speaker cables.
c Cooling Fan
d Antenna Connector
FM- Connects the FM wired antenna
e SCART connetcor
f VIDEO OUT
Connects to a TV with video inputs.
HT806PH-D0_BGBRLL_ENG_4756.indd 11
c
d
e
Getting Started
f
jih
g
g HDMI OUT
Connects to TV with HDMI inputs.
(Interface for digital audio and video)
h OPTICAL IN
Connects to optical audio equipment.
i COMPONENT VIDEO (Y PB PR)OUTPUT
(PROGRESSIVE SCAN)
Connects to a TV with Y PB PR inputs.
j AUX (L/R) INPUT
Connects to an external source with 2 channel
audio outputs.
2011-02-15 �� 10:10:50
12
Connecting
Assembling the
speaker stand to the
speaker
2
Attach the speakers to the speaker stands by
rotating the screws.
Before connecting the speakers, assemble the
speakers. Please check the items for assembling the
speakers.
Connecting
Preparation
Speaker
Stand
HT806PH-D0_BGBRLL_ENG_4756.indd 12
2011-02-15 �� 10:10:51
Connecting
Attaching the speakers
to the unit
Speaker
Position
Grey
Rear
Rear right
Blue
Rear
Rear left
Green
Center
Center
Orange
Sub woofer
Any front position
Red
Front
Front right
White
Front
Front left
2
To connect the cable to the speakers, press each
plastic finger pad to open the connection terminals
on the base of each speaker. Insert the wire and
release the finger pad.
Connecting
1. Connect the wires to the unit.
Match each wire’s colored band to the same
colored connection terminal on the rear of the
unit. To connect the cable to the unit, press
each plastic finger pad to open the connection
terminal. Insert the wire and release the finger
pad.
Color
13
>>Caution
Connect the black stripe of each wire to the
terminals marked -(minus) and the other end
to the terminals marked + (plus).
2. Connect the wires to the speakers.
Connect the other end of each wire to the
correct speaker according to the color coding:
HT806PH-D0_BGBRLL_ENG_4756.indd 13
yy Be careful to make sure children do not put
their hands or any objects into the *speaker
duct.
*Speaker duct : A hole for plentiful bass
sound on speaker cabinet (enclosure).
yy The speakers contain magnet parts, so color
irregularity may occur on the TV screen or
PC monitor screen. Please use the speakers
far away from either TV screen or PC
monitor.
2011-02-15 �� 10:10:51
14
Connecting
Positioning the system
The following illustration shows an example of
positioning the system. Note that the illustrations
in these instructions differ from the actual unit for
explanation purposes.
2
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
Connecting
position ( ).
B
G
A
A
A
D
Surround left speaker (L)/ Surround right
speaker (R):
Place these speakers behind your listening
position, facing slightly inwards.
Unit
F
A
Center speaker: Place the center speaker above
or below the monitor or screen.
Subwoofer: The position of the subwoofer is
not so critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it slightly
toward the center of the room to reduce the wall
reflections.
C
A
Front left speaker (L)/ Front right speaker (R):
Place the front speakers to the sides of the
monitor or screen and as flush with the screen
surface as possible.
E
A
A ABCD E F G
HT806PH-D0_BGBRLL_ENG_4756.indd 14
2011-02-15 �� 10:10:52
Connecting
Connections to Your
TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
,,Note
15
Component Video Connection
Connect the COMPONENT VIDEO OUTPUT
(PROGRESSIVE SCAN) jacks on the unit to the
corresponding input jacks on the TV using
component cables.
You can hear the sound through the system’s
speakers.
yy Depending on your TV and other
equipment you wish to connect, there are
various ways you could connect the player.
Use only one of the connections described
in this manual.
2
Connecting
Unit
yy Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
>>Caution
yy Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel.
yy Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
TV
Green
Blue
Red
HT806PH-D0_BGBRLL_ENG_4756.indd 15
2011-02-15 �� 10:10:52
16
Connecting
,,Note
HDMI Out Connection
If you have a HDMI TV or monitor, you can connect
it to this unit using a HDMI cable (Type A, High
Speed HDMI™ Cable).
Connect the HDMI OUT jack on the unit to the
HDMI IN jack on a HDMI compatible TV or monitor. Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
2
yy If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or
may not output.
yy When you connect a HDMI or DVI
compatible device make sure of the
following:
Connecting
- Try switching off the HDMI/DVI device
and this unit. Next, switch on the HDMI/
DVI device and leave it for around 30
seconds, then switch on this unit.
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or 576p), 1
280 x 720p, 1 920 x 1 080i or 1 920 x 1 080p
video input.
Unit
TV
,,Tip
yy You can fully enjoy digital audio and video
signals together with this HDMI connection.
yy When you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 18.)
yy Not all HDCP-compatible HDMI or DVI
devices will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
yy If there is noise or lines on the screen, please
check the HDMI cable and use a higher
version cable than High Speed HDMI™
Cable.
>>Caution
yy Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the unit and then turn it
on again.
yy When the HDMI connection with HDCP is
not verified, TV screen is changed to black
or green screen or the snow noise may
occur on the screen. In this case, check the
the HDMI connection, or disconnect the
HDMI cable.
HT806PH-D0_BGBRLL_ENG_4756.indd 16
2011-02-15 �� 10:10:53
Connecting
17
Video Connection
SCART Connection
Connect the VIDEO OUT jack on the unit to the
video in jack on the TV using a video cable.
Connect the SCART jack on the unit to the SCART in
jack on the TV using a SCART cable.
You can hear the sound through the system’s
speakers.
You can hear the sound through the system’s
speakers.
Unit
Unit
2
Connecting
TV
TV
Yellow
HT806PH-D0_BGBRLL_ENG_4756.indd 17
2011-02-15 �� 10:10:54
18
Connecting
Resolution Setting
The unit provides several output resolutions for
HDMI OUT and COMPONENT VIDEO OUT jacks. You
can change the resolution using [Setup] menu.
1. Press n HOME.
2. Use A/D to select the [Setup] and press b
ENTER. The [Setup] menu appears.
2
Video Output
Resolution
Displayed resolution in display window and
outputted resolution may different according to
connection type.
[HDMI OUT]: 1 080p, 1 080i, 720p and 480p (or
576p) and 480i (or 576i)
Connecting
[COMPONENT VIDEO OUT]: 480p (or 576p) and 480i
(or 576i)
[VIDEO OUT]: 480i (or 576i)
3. Use W/S to select [Display] option then press
D to move to the second level.
4. Use W/S to select the [Resolution] option
then press D to move to the third level.
5. Use W/S to select the desired resolution then
press b ENTER to confirm your selection.
,,Note
If your TV does not accept the resolution you
have set on the player, you can set resolution
to 480p (or 576p) as follows:
Press Z STOP for more than 5 seconds.
HT806PH-D0_BGBRLL_ENG_4756.indd 18
2011-02-15 �� 10:10:54
Connecting
Optional Equipment
Connection
19
AUDIO (PORT. IN) In
Connection
Connect an output of portable device (MP3 or PMP
etc) to the AUDIO (PORT. IN) input connector.
AUX In Connection
Connect an Output of auxiliary device to the AUX
(L/R) INPUT Connector.
2
Connecting
Unit
MP3 player, etc...
Listening to music from your
portable player or external
device
The unit can be used to play the music from many
types of portable player or external devices.
To the audio output jacks
of your component
(TV, VCR, etc.)
1. Connect the portable player to the PORT. IN (PORTABLE IN) connector of the unit.
Red
White
,,Note
If your TV has only one output for audio
(mono), connect it to the left (white) audio jack
on the unit.
HT806PH-D0_BGBRLL_ENG_4756.indd 19
Or
Connect the external device to the AUX
connector of the unit.
2. Turn the power on by pressing 1 (POWER).
3. Select the PORTABLE or AUX (L/R) INPUT
function by pressing P RADIO&INPUT.
4. Turn on the portable player or external device
and start it playing.
2011-02-15 �� 10:10:54
20 Connecting
USB Connection
Compatible USB Devices
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the front of the unit.
yy MP3 Player : Flash type MP3 player.
evices that support USB2.0 or
yy USB Flash Drive : D
USB1.1.
yy The USB function of this unit does not support
some USB devices.
USB device requirement
2
Connecting
yy Devices which require additional program
installation connected to a computer, are not
supported.
yy Do not extract the USB device while in operation.
Removing the USB Device from the unit
1. Choose a different function mode or press Z
STOP twice in a row.
2. Remove the USB device from the unit.
yy For a large capacity USB, it may take longer than
a few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported. (Only
FAT(16/32) file system is supported.)
yy This unit is not supported when the total
number of files is 1 000 or more.
yy External HDD, Card readers, Locked devices, or hard type usb devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit can not be used as a storage device.
HT806PH-D0_BGBRLL_ENG_4756.indd 20
2011-02-15 �� 10:10:55
Connecting
OPTICAL In connection
Connect an optical output of Unit (or Digital Device
etc) to the OPTICAL IN connector.
21
Antenna Connection
Connect the supplied FM antenna for listening to
the radio.
Connect the FM Wire antenna to the FM antenna
connector.
2
Connecting
To the digital
optical output jack
of your component
Home theater speaker ez
setup
Listen to sound from TV, DVD and Digital Device
with 5.1(2.1 or 2)ch mode. Even in power off
mode, if you press OPTICAL, then power is on and
automatically changed to AUX OPT mode.
,,Note
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it
as horizontal as possible.
1. Connect the unit’s OPTICAL IN jack to jack on
optical out of your TV (or Digital Device etc.).
2. Select the AUX OPT by using the OPTICAL.
To select the AUX OPT directly.
3. Listen sound with 5.1(2.1 or 2)ch speaker.
4. To escape from AUX OPT by using the OPTICAL.
Function is retuned to previous one.
HT806PH-D0_BGBRLL_ENG_4756.indd 21
2011-02-15 �� 10:10:55
22 System Setting
Adjust the setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
To display and exit the Setup
menu
1. Press n HOME.
Displays the [Home Menu].
You can also set a language for the subtitles and
the Setup menu, among other things. For details on
each Setup menu item, see pages 22 to 26.
OSD Initial language settings
- Optional
3
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using
the unit. English will be selected as the initial
language.
1. Press 1 (POWER) to turn the unit on. The
language setup menu will appear on the screen.
2. Select an [Setup] by using AD.
3. Press b ENTER.
Displays the [Setup].
4. Press n HOME or x RETURN to exit in the
[Setup] Menu.
About help menu for Setup
Menu
Buttons
Operation
WS
Moving to another
menu.
a
Move
A
Moving to previous
level.
d
Move
D
Moving to next
level or selecting
menu.
x RETURN
To exit the [Setup]
menu or [ 5.1
Speaker Setup].
b ENTER
To confirm menu.
ws
Move
x
2. Use WSAD to select a language then press
b ENTER.
The confirm menu will appear.
Close
b
Select
3. Use AD to select the [Enter] then press b
ENTER to finish the language setup.
HT806PH-D0_BGBRLL_ENG_4756.indd 22
2011-02-15 �� 10:10:55
System Setting 23
Language
Menu Language
Select a language for the Setup menu and then on
screen display.
Disc Audio / Disc Subtitle / Disc
Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
[Panscan]
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with
Pan Scan, the picture is displayed at Letterbox
ratio.)
TV Output Select
Select an option according to the TV connection
type.
[RGB]
When your TV is connected with the SCART
jack.
[Other]
[YPBPR]
To select another language, press numeric
buttons and then b ENTER to enter the
corresponding 4-digit number according to
the language code list on the page 39. If you
enter the wrong language code, press CLEAR.
[Off (for Disc Subtitle)]
Turn off Subtitle.
Display
TV Aspect
Select which screen aspect to use based on the
shape of your TV screen.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
When your TV is connected with the
COMPONENT/ PROGRESSIVE SCAN jacks on the
unit.
Resolution
Sets the output resolution of the Component and
HDMI video signal. Refer to “Resolution Setting” for
details about the resolution (page 18).
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV. If the COMPONENT
VIDEO OUT is only connected, this changes the
resolution to 480i (or 576i) as default resolution.
[1080p]
Outputs 1 080 lines of progressive video.
[1080i]
Outputs 1 080 lines of interlaced video.
Display Mode
[720p]
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
Outputs 720 lines of progressive video.
[480p (or 576p)]
[Letterbox]
Outputs 480 (or 576) lines of progressive video.
Displays a wide picture with bands on the
upper and lower portions of the screen.
[480i (or 576i)]
HT806PH-D0_BGBRLL_ENG_4756.indd 23
3
System Setting
Refers to the original language in which the
disc was recorded.
Outputs 480 (or (576) lines of interlaced video.
2011-02-15 �� 10:10:55
24 System Setting
Audio
5.1 Speaker Setup
Make the following settings for the built-in 5.1
channel surround decoder.
[Speaker]
Select a speaker that you want to adjust.
,,Note
Certain speaker settings are prohibited by the
Dolby Digital licensing agreement.
1. Select [5.1 Speaker Setup] on the [Audio] menu.
2. Press b ENTER.
The [5.1 SPEAKER] appears.
[Size]
Since the speaker settings are fixed, you cannot
change the settings.
[Volume]
Press AD to adjust the output level of the
selected speaker.
3
System Setting
Front L/R : 0 ~ -5
SubWoofer, Rear L/R, Center : 5 ~ -5
3. Use AD to select the desired speaker.
4. Adjust options using WSAD buttons.
5. Returns to the previous menu by pressing x
RETURN.
[Distance]
After you connected speakers to your unit,
set the Distance between the speakers and
your listening point if the distance of Center
or Rear speakers is bigger than the distance
of Front speakers. This allows the sound from
each speaker to reach the listener at the same
time. Press AD to adjust the Distance of the
selected speaker. This distance is equivalent to
a difference of the distance between Center or
Rear speaker and Front speakers.
[Test]
Select [Speaker Test Start] by using the WS
and press b ENTER. Press b ENTER again to
stop. Adjust the volume to match the volume
of test signals memorized in the system.
HT806PH-D0_BGBRLL_ENG_4756.indd 24
2011-02-15 �� 10:10:55
System Setting 25
DRC (Dynamic Range Control)
Lock (Parental Control)
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [On] for this effect.
Initial Setting the Area Code:
Vocal
When you use this unit for the first time, you have
to set the Area Code.
Select [On] to mix karaoke channels into normal
stereo.
1. Select the [Lock] menu and then press D.
This function is effective for multi-channel karaoke
DVDs only.
HD AV Sync
3. Select the first character using WS buttons.
4. Press b ENTER and select the second character
using WS buttons.
5. Press b ENTER to confirm your Area code
selection.
Rating
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
3
System Setting
Sometimes Digital TV encounters a delay between picture and sound. If this happens you can
compensate by setting a delay on the sound so
that it effectively ‘waits’ for the picture to arrive:
this is called HD AV Sync. Use WS (on the remote
control) to scroll up and down through the delay
amount, which you can set at anything between 0
and 300m sec.
2. Press D.
To access the [Lock] options, you must input the
password you have created. Input a password
and press b ENTER. Enter it again and press b
ENTER to verify. If you make a mistake before
pressing b ENTER, press CLEAR.
1. Select [Rating] on the [Lock] menu then press
D.
2. Input a password and press b ENTER.
3. Select a rating from 1 to 8 using the WS
buttons.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not
active and the disc plays in full.
4. Press b ENTER to confirm your rating selection.
HT806PH-D0_BGBRLL_ENG_4756.indd 25
2011-02-15 �� 10:10:55
26 System Setting
Password
Others
You can enter or change password.
1. Select [Password] on the [Lock] menu and then
press D.
2. Press b ENTER.
3. Input a password and press b ENTER.
To change the password, press b ENTER when
the [Change] option is highlighted. Input a
password and press b ENTER. Enter it again
and press b ENTER to verify.
4. Press n HOME to exit the menu.
,,Note
3
If you forget your password, you can clear it
using the following steps:
System Setting
1. Select the [Setup] menu on the [Home
Menu].
2. Input the 6-digit number “210499” and
press b ENTER. The password is cleared.
DivX VOD
We provide you with the DivX® VOD (Video On
Demand) registration code that allows you to rent
and purchase videos using the DivX® VOD service.
For more information, visit www.divx.com/vod.
[Register]
Displays the registration code of your player.
[Deregister]
Deactivate your player and display the
deactivation code.
,,Note
All the downloaded videos from DivX VOD can
only be played back on this unit.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 38.
1. Select [Area Code] on the [Lock] menu then
press D.
2. Input a password and press b ENTER.
3. Select the first character using WS buttons.
4. Press b ENTER and select the second character
using WS buttons.
5. Press b ENTER to confirm your Area code
selection.
HT806PH-D0_BGBRLL_ENG_4756.indd 26
2011-02-15 �� 10:10:56
Operating 27
Using the Home Menu
Basic Operations
1. Press n HOME.
Displays the [Home Menu].
1. Insert the disc by using the B OPEN/CLOSE or
Connect the USB device to the USB port.
2. Press n HOME.
Displays the [Home Menu].
2. Select an option by using AD.
3. Press b ENTER then selected option menu.
3. Select an option by using AD.
If you select the [Movie], [Photo] or [Music]
option when you connect up to two devices,
it appears as belows. Select a media then press
b ENTER.
[Music] – Displays [MUSIC] menu.
[Movie] – Start video media’s playback or displays
the [MOVIE] menu.
[Photo] – Displays [PHOTO] menu.
[Setup] – Displays the [Setup] menu.
,,Note
HT806PH-D0_BGBRLL_ENG_4756.indd 27
,,Note
yy For the most Audio CD and DVD-ROM discs,
playback starts automatically.
yy The unit plays only music file contained in
the USB storage device or disc automatically.
4
Operating
You can not select the [Music], [Movie] or
[Photo] option when the USB device is not
connected or a disc is not inserted.
4. Press b ENTER then selected option menu.
2011-02-15 �� 10:10:56
28 Operating
To
Stop
Do this
Press Z STOP.
Playback
Press d PLAY, MONO/
STEREO.
Pause
Press M PAUSE/STEP.
Press M PAUSE/STEP
Frame-byrepeatedly to play title FrameFrame playback
by-Frame. (DVD, DivX only)
During playback, press C/
V SKIP to go to the next
Skipping to the chapter/ track/ file or to
next/ previous return to the beginning of the
chapter/ track/ current chapter/ track/ file.
file
Press C SKIP twice briefly
to step back to the previous
chapter/ track/ file.
4
Operating
During playback, press c/
Locating a
v SCAN repeatedly to
point quickly by select the required scan speed.
playing a file in
fast forward or To return to normal speed,
press d PLAY, MONO/
fast reverse
STEREO.
Playing
repeatedly or
randomly
Other Operations
Press h REPEAT repeatedly,
and the current title, chapter
or track will be played back
repeatedly or randomly.
Displaying Disc Information
on-screen
You can display various information about the disc
loaded on-screen.
1. Press m INFO/DISPLAY to show various
playback information.
The displayed items differ depending on the
disc type or playing status.
2. You can select an item by pressing WS and
change or select the setting by pressing AD.
Title – Current title number/ total number of titles.
Chapter – Current chapter number/ total number
of chapters.
Time – Elapsed playing time.
Audio – Selected audio language or channel.
Subtitle – Selected subtitle.
Angle – Selected angle/ total number of angles.
,,Note
If any button is not pressed for a few seconds,
the on-screen display disappears.
- DVD : Chapter/ Title/ Off
- DivX : Title/ All/ Off
- Audio CD/ MP3/ WMA : Track/
All/ Random/ Off
Slowing down
the playing
speed
In the pause mode, press
SLOW (c or v) to select
the required speed. (DVD, DivX
only) The DivX file cannot be
slow down reverse playback.
HT806PH-D0_BGBRLL_ENG_4756.indd 28
2011-02-15 �� 10:10:56
Operating 29
To display the DVD Menu
r
When you play a DVD which contains several menu,
you can select the menu you want using the Menu.
1. Press DISC MENU.
The disc’s menu appears.
2. Select the menu by using WSAD.
3. Press d PLAY, MONO/STEREO to confirm.
To display the DVD title
r
When you play a DVD which contains several title,
you can select the title you want using the Menu.
1. Press TITLE.
The disc’s title appears.
2. Select the menu by pressing WSAD.
3. Press d PLAY, MONO/STEREO to confirm.
r
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
1. During playback, press d PLAY, MONO/
STEREO to play at 1.5 times speed. “dX1.5”
appears on the screen.
2. Press d PLAY, MONO/STEREO again to exit.
Screen Saver
The screen saver appears when you leave the unit
in Stop mode for about five minutes.
ry
To start playing at any chosen time on the file or
title.
1. Press m INFO/DISPLAY during playback.
2. Press WS to select the time clock icon and
“--:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR to remove the
numbers you entered. Then input the correct
numbers.
For example, to find a scene at 1 hour, 10
minutes, and 20 seconds, enter “11020” by using
numerical buttons.
4. Press b ENTER to confirm. Playback starts from
the selected time.
4
Resume playback
ryut
The unit records the point where you pressed the
Z STOP depending on the disc.
If “MZ (Resume Stop)” appears on the screen briefly,
press d PLAY, MONO/STEREO to resume playback
(from the scene point).
Operating
1.5 times speed playback
Starting play from selected
time
If you press Z STOP twice or unload the disc,
“Z”(Complete Stop) appears on the screen. The
unit will clear the stopped point.
,,Note
The resume point may be cleared when a
button is pressed (for example; 1 (POWER),
B OPEN/CLOSE, etc).
Changing subtitle code page
y
If the subtitle is not displayed properly, you can
change the subtitle code page to view the subtitle
file properly.
1. During playback, press m INFO/DISPLAY to
display the On-Screen display.
2. Use WS to select the [Code Page] option.
3. Use AD to select desired code option.
4. Press x RETURN to exit the On-Screen display.
HT806PH-D0_BGBRLL_ENG_4756.indd 29
2011-02-15 �� 10:10:56
30 Operating
Marked Playback
ut
The mark function enables you to store your
favourite files from any disc or USB device in the
unit memory.
1. Select [Music] on the [Home Menu].
Returning to the upper folder.
(MP3/ WMA only)
File information will be displayed
according to the ID3TAG information
on the appropriate music file. (MP3
only)
To delete a Marker
1. Use WS to select the track that you wish to erase
from the marked file.
2. Press MARKER.
To delete all Markers
Use WSAD to select [Deselect All] then press b
ENTER in program edit mode.
,,Note
The markers are also cleared when the disc or
USB device is removed, the unit is switched to
power off or the function is switched to others.
4
Operating
Selecting all tracks/ files.
Deselecting all tracks/files.
Moving to the previous or
next file list.
2. Select a desired music on the [List] by using the
WS then press MARKER to appears the mark on
the list.
3. Press b ENTER or d PLAY, MONO/STEREO.
Displays the play mode.
4. Select the play mode by using the WS and press
b ENTER.
[Mark Play]
Marked playback.
[Current Play]
Normal playback.
,,Note
If you want to select all files on the list, select
[Select All] and press b ENTER.
HT806PH-D0_BGBRLL_ENG_4756.indd 30
2011-02-15 �� 10:10:56
Operating
Viewing a PHOTO file
About help menu in the full screen
Menu
Buttons
Operation
Menu
m
INFO/
DISPLAY
Displaying the Option
menu.
a/d
Prev./ Next
A/D
Moving to another file.
i
This unit can play discs with photo files.
1. Select [Photo] on the [Home Menu] and press
b ENTER.
Moving to the previous or
next file list.
31
x,
Close
x
RETURN
Returning to the
[Photo] menu.
Options while viewing a photo
You can use various options during viewing a
photo in full screen.
1. While viewing a photo in full screen, press m INFO/DISPLAY to display the option menu.
2. Select an option using WSAD.
Returning to the upper
folder.
4
3. If you want to view a slide show, press WS
to highlight a file and press d PLAY, MONO/
STEREO.
About help menu in the [Photo] menu
Menu
Buttons
d Slide
Show
d
PLAY, MONO/
STEREO
wsad
Move
WSAD
Moving to another
file or content.
b
Select
b ENTER
Viewing a particular
file.
x
Close
x RETURN
Operation
Viewing a slide
show.
Returning to the
[Home Menu].
HT806PH-D0_BGBRLL_ENG_4756.indd 31
Operating
2. Press WS to select a folder, and then press b
ENTER.
a
b
c
d
e
a Current photo/ Total number of photos –
Use AD to view previous/next photo.
b Slide Show z/M– Press  ENTER to start
or pause slide show.
c Speed x3/ x2/ x1 – Use  ENTER to select
a delaying speed between photos in a slide
show.
d Rotate – Press  ENTER to rotate the photo.
e Go to list – Press  ENTER to return [Photo]
menu.
2011-02-15 �� 10:10:56
32 Operating
Sleep Timer Setting
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will
turn off.
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
,,Note
You can check the remaining time before the
Unit turns off.
Adjust the speaker level
settings
You can adjust the sound level of each speaker.
1. Press SPEAKER LEVEL repeatedly to select a
desired speaker to set.
2. Press VOL -/+ to adjust the sound level of the
selected speaker while the level setting memu
is displayed on the display window.
3. Repeat and adjust the sound level of the other
speakers.
Press SLEEP The remaining time appears in the
display window.
Dimmer
4
Press SLEEP once. The display window will be
darken by half. To cancel it, press SLEEP repeatedly
until dim off.
Operating
Turn off the sound temporarily
Press
MUTE to mute your unit.
You can mute your unit in order, for example, to
answer the telephone, appears the MUTE in the
display window.
Last Scene Memory
r
This unit memorizes last scene from the last disc
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
off the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
System Select - Optional
You must select the appropriate system mode for
your TV system. Press and hold M PAUSE/STEP
for more than five seconds to be able to select a
system in the [Home Menu].
,,Note
If the USB device is connected or a disc is
inserted, this function is not operated.
HT806PH-D0_BGBRLL_ENG_4756.indd 32
2011-02-15 �� 10:10:56
Operating 33
Radio Operations
Be sure that both FM aerials are connected. (Refer
to the page 21.)
Listening to the radio
1. Press P RADIO&INPUT until FM appears in
the display window.
The last received station is tuned in.
2. Press and hold TUNING (-/+) for about two
seconds until the frequency indication starts to
change, then release. Scanning stops when the
unit tunes in a station.
or
Press TUNING (-/+) repeatedly.
3. Adjust the volume by rotating VOLUME on
the front panel or by pressing VOL (+/-)on the
remote control repeatedly.
1. Press PRESET - / + to Select a preset number
you want to delete.
2. Press CLEAR, the preset number will blink in the
display window.
3. Press CLEAR again, to delete the selectd preset
number.
Improving poor FM reception
Press d PLAY, MONO/STEREO on the remote
control. This will change the tuner from stereo to
mono and usually improve the reception.
Seeing information about a
radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about
the radio station being listened to. Press RDS
repeatedly to cycle through the various data types.
PS ( Programme Service Name)
The name of the channel will appear in
the display
PTY ( Programme Type Recognition)
The programme type (e.g. Jazz or News)
will appear in the display.
RT ( Radio Text)
A text message contains special
information from the broadcast station.
This text may scroll across the display.
CT ( Time controlled by the channel)
This shows the time and date as
broadcast by the station.
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
1. Press P RADIO&INPUT until FM appears in
the display window.
2. Select the desired frequency by using TUNING
(-/+).
3. Press b ENTER a preset number will flash in
the display window.
4. Press PRESET (-/+) to select the preset number
you want.
5. Press b ENTER.
The station is stored.
6. Repeat the steps 2 to 5 to store other stations.
Deleting all the saved stations
1. Press and hold CLEAR for two seconds.
“ERASE ALL” will flash up on the unit display.
4
Operating
Presetting the Radio Stations
Deleting a saved station
You can search the radio stations by programme
type by pressing RDS. The display will show the last
PTY in use. Press PTY one or more times to select
your preferred programme type. Press AD. The
tuner will search automatically, when a station is
found the search will stop.
2. Press CLEAR to erase all saved of the radio
stations.
HT806PH-D0_BGBRLL_ENG_4756.indd 33
2011-02-15 �� 10:10:56
34 Operating
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound fields. You can select a desired sound mode
by using SOUND EFFECT.
You can change the SOUND EFFECT using AD
arrow key while the sound effect information is
displayed on.
The displayed items for the equalizer maybe
different depending on sound sources and effects.
4
Operating
On Display
Description
NAT PLUS
The NAT PLUS is Natural Plus
sound effect. You can enjoy
the natural sound effect same
as a 5.1-channel.
NATURAL
You can enjoy comfortable
and natural sound.
Local
specialization
equalizer
Regionally optimized sound
effect. (DANGDUT/ ARABIC/
PERSIAN/ INDIA/ REGUETON/
MERENGUE/ SAMBA/ SALSA/
CUMBIA/ AFRO)
AUTO EQ
Realizes the sound equalizer
that is the most similar to the
genre of which is included in
the MP3 ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
On Display
Description
VIRTUAL
The VIRTUAL is VSM Plus.
You can enjoy more virtual
surround sound.
BYPASS
You can enjoy the sound
without equalizer effect.
,,Note
yy In some of surround modes, some speakers,
there’s no sound or low sound. It depends
on the mode of surround and the source of
audio, it is not defective.
yy You may need to reset the surround mode,
after switching the input, sometimes even
after the sound track changed.
This program lends an
enthusiastic atmosphere to
the sound, giving you the
feeling you are at an actual
rock pop, jazz or classic
concert.
MP3 OPT
This function is optimized for
compressible MP3, WMA file. It
improves the treble sound.
BASS
The BASS is Bass Blast. During
playback, reinforce the treble,
bass and surround sound
effect.
LOUDNESS
Improves the bass and treble
sound.
HT806PH-D0_BGBRLL_ENG_4756.indd 34
2011-02-15 �� 10:10:56
Operating 35
Advanced Operations
,,Note
Recording to USB
yy You can check the recording percentage
rate for the USB record on the screen during
the recording. (Audio CD or MP3/ WMA CD
only)
You can record music or sound souce to USB device
by connecting in to the port on the unit.
yy During recording MP3/WMA, there is no
sound.
1. Connect the USB device to the unit.
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Audio CD only)
2. Select a mode in which you want to record.
Play back a sound source first.
3. Start the recording by pressing X REC.
4. To stop recording, press Z STOP.
[All tracks/ files recording]
Record to USB in stop or play mode.
[Program list recording]
After marking desired file(s) and you can record
it to USB (Refer to the page 30).
It’ll be stored as follows.
MP3/ WMA
yy If USB recording does not work, the
message like “NO USB”, “ERROR”, “USB FULL”
or “NO REC” is displayed on the display
window.
yy Multi card reader device or external HDD
can not be used for USB recording.
yy A file is recorded by 128 Mbyte (about 2
hours) when you record for a long term.
There are recorded less than 4 files.
yy When you stop recording during playback,
the file will not be stored.
4
Operating
Audio CD
yy Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
yy In the state CD-G, DTS disc USB record is not
operated.
yy The files in the sub-folders are not recorded
during all track recording.
yy You may not record more than 999 files.
The other
sources (Tuner,
AUX, Portable)
yy The numbering of the recording file is
entered from the lowest number. So if you
delete some of the recording files, the next
recording file could be the lowest number
among them.
The making of unauthorized copies of copyprotected material, including computer programs,
files, broadcasts and sound recordings, may be
an infringement of copyrights and constitute a
criminal offense. This equipment should not be
used for such purposes.
Be responsible
Respect copyrights.
HT806PH-D0_BGBRLL_ENG_4756.indd 35
2011-02-15 �� 10:10:56
36 Troubleshooting
Troubleshooting
PROBLEM
No power
No picture
CORRECTION
Plug the power cord into the wall outlet securely.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
Connect the video cables securely to both the TV and unit.
Select the correct input mode of the unit so you can hear the sound
from the unit.
There is little or no sound
Connect the audio cables into the connection terminals correctly.
Replace with a new audio cable.
The DVD picture quality is poor
Clean the disc using a soft cloth with outward strokes.
Insert a disc.
A DVD/CD will not play
Insert a playable disc (check the disc type, colour system and
regional code).
Place the disc with the label or printed side facing upwards.
Enter your password or change the rating level.
5
Troubleshooting
Humming noise heard while a DVD
or CD is playing
Clean the disc using a soft cloth with outward strokes.
Move unit and audio components further away from your TV.
Check the antenna connection and adjust its position.
Radio stations can’t be tuned in
properly
Attach an external aerial if necessary.
Tune to the station manually.
Preset some radio stations, see page 33 for details.
The remote is not pointed directly at the unit.
Point the remote directly at the unit.
The remote is too far from the unit.
Use the remote within 23 feet (7m) of the unit.
The remote control doesn’t work
well / at all
There is an obstacle in the path between the remote control and
the unit.
Remove the obstacle.
The battery in the remote control are flat.
Replace the battery with new ones.
HT806PH-D0_BGBRLL_ENG_4756.indd 36
2011-02-15 �� 10:10:56
Appendix 37
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
yy Do not use volatile liquids such as insecticide
spray near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Maintaining the Unit
HT806PH-D0_BGBRLL_ENG_4756.indd 37
6
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
2011-02-15 �� 10:10:57
38 Appendix
Area Code List
Choose an area code from this list.
Area
Afghanistan Code Area
AF Fiji Code Area
Code Area
Code
FJ Monaco MC Singapore SG
SK
Argentina AR Finland FI Mongolia MN Slovak Republic Australia AU France FR Morocco MA Slovenia Austria AT Germany DE Nepal NP South Africa ZA
Belgium BE Great Britain GB Netherlands NL South Korea KR
Bhutan BT Greece GR Antilles AN Spain ES
Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK
SI
Brazil BR Hong Kong HK Nigeria NG Sweden SE
Cambodia KH Hungary HU Norway NO Switzerland CH
Canada CA India IN Oman OM Taiwan TW
Chile CL Indonesia ID Pakistan PK Thailand China CN Israel IL Panama PA Turkey TR
Colombia CO Italy IT Paraguay PY Uganda UG
Congo CG Jamaica JM Philippines PH Ukraine UA
Costa Rica CR Japan JP Poland PL United States US
Croatia HR Kenya KE Portugal PT Uruguay UY
Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ
Denmark DK Libya Ecuador EC Luxembourg Egypt EG Malaysia 6
El Salvador SV Maldives MY Saudi Arabia MV Senegal Appendix
Ethiopia ET Mexico MX
HT806PH-D0_BGBRLL_ENG_4756.indd 38
LY Russian LU Federation Vietnam RU Zimbabwe SA
TH
VN
ZW
SN
2011-02-15 �� 10:10:57
Appendix 39
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu].
Code
Language
Code
Language
Code
Language
Afar 6565
French 7082
Lithuanian 7684
Sindhi 8368
Afrikaans 6570
Frisian 7089
Macedonian 7775
Singhalese 8373
Albanian 8381
Galician 7176
Malagasy 7771
Slovak 8375
Ameharic 6577
Georgian 7565
Malay 7783
Slovenian 8376
Arabic 6582
German 6869
Malayalam 7776
Spanish 6983
Armenian 7289
Greek 6976
Maori 7773
Sudanese 8385
Assamese 6583
Greenlandic 7576
Marathi 7782
Swahili 8387
Aymara 6588
Guarani 7178
Moldavian 7779
Swedish 8386
Azerbaijani 6590
Gujarati 7185
Mongolian 7778
Tagalog 8476
Bashkir 6665
Hausa 7265
Nauru
7865
Tajik 8471
Basque 6985
Hebrew 7387
Nepali 7869
Tamil 8465
Bengali; Bangla 6678
Hindi 7273
Norwegian 7879
Telugu 8469
Bhutani 6890
Hungarian 7285
Oriya 7982
Thai 8472
Bihari 6672
Icelandic 7383
Panjabi 8065
Tonga 8479
Breton 6682
Indonesian 7378
Pashto, Pushto 8083
Turkish 8482
Bulgarian 6671
Interlingua 7365
Persian 7065
Turkmen 8475
Burmese 7789
Irish 7165
Polish 8076
Twi 8487
Byelorussian 6669
Italian 7384
Portuguese 8084
Ukrainian 8575
Chinese 9072
Japanese 7465
Quechua 8185
Urdu 8582
Croatian 7282
Kannada 7578
Rhaeto-Romance 8277
Uzbek 8590
Czech 6783
Kashmiri 7583
Rumanian 8279
Vietnamese 8673
Danish 6865
Kazakh 7575
Russian 8285
Volapük 8679
Dutch 7876
Kirghiz 7589
Samoan 8377
Welsh 6789
English 6978
Korean 7579
Sanskrit 8365
Wolof 8779
Esperanto 6979
Kurdish 7585
Scots Gaelic 7168
Xhosa 8872
Estonian 6984
Laothian 7679
Serbian 8382
Yiddish 7473
Faroese 7079
Latin 7665
Serbo-Croatian 8372
Yoruba 8979
Fiji 7074
Latvian, Lettish 7686
Shona 8378
Zulu 9085
Finnish 7073
Lingala 7678
HT806PH-D0_BGBRLL_ENG_4756.indd 39
Code
6
Appendix
Language
2011-02-15 �� 10:10:57
40 Appendix
Trademarks and
Licenses
What is SIMPLINK?
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Some functions of this unit are controlled by
TV’s remote control when this unit and LG TV
with SIMPLINK are connected through HDMI
connection. Controllable functions by LG TV’s
remote control; Play, Pause, Scan, Skip, Stop,
Power Off, etc.
yy Refer to the TV owner’s manual for the details
of SIMPLINK function.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
yy LG TV with SIMPLINK function has the logo as
shown above.
yy Use a higher version cable than High Speed
HDMI™ Cable.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
DivX®, DivX Certified® and associated logos are
trademarks of DivX, Inc. and are used under
license.
6
Appendix
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, Inc. This is an official
DivX Certified® device that plays DivX video.
Visit www.divx.com for more information and
software tools to convert your files into DivX
video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to
play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate
the DivX VOD section in your device setup menu.
Go to vod.divx.com for more information on how
to complete your registration.
HT806PH-D0_BGBRLL_ENG_4756.indd 40
2011-02-15 �� 10:10:57
Appendix
41
Specifications
General
Power requirements
200 - 240 V, 50/60 Hz
Power consumption
95 W
Dimensions (W x H x D)
360 x 62.5 x 312.3 mm without foot
Net Weight (Approx.)
2.8 kg
Operating temperature
41 °F to 95 °F (5 °C to 35 °C)
Operating humidity
5 % to 90 %
Bus Power Supply (USB)
DC 5 V 0 500 mA
Inputs/ Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
COMPONENT VIDEO OUT
(Y) 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 Ω, RCA jack x 2
HDMI OUT (video/audio):
19 pin (Type A, HDMI™ Connector )
ANALOG AUDIO IN
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL IN (OPTICAL):
3 V (p-p), Optical jack x 1
PORT. IN
0.5Vrms (3.5 mm stereo jack)
Amplifier
Stereo mode
Surround mode
141 W + 141 W (3 Ω at 1kHz)
141 W + 141 W (3 Ω at 1 kHz)
Surround
141 W + 141 W (3 Ω at 1 kHz))
Subwoofer
145 W (3 Ω at 60 Hz)
141 W (3 Ω at 1 kHz)
Tuner
FM Tuning Range
HT806PH-D0_BGBRLL_ENG_4756.indd 41
6
Appendix
Front
Center
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
2011-02-15 �� 10:10:57
42 Appendix
Front Speaker
Type
2 Way 2 speaker
Impedance Rated
3Ω
Input Power
141 W
Max. Input Power
282 W
Net Dimensions (W x H x D)
260 x 1 102 x 200 mm
Net Weight
2.68 kg
Rear Speaker
Type
1 Way 1 Speaker
Impedance Rated
3Ω
Input Power
141 W
Max. Input Power
282 W
Net Dimensions (W x H x D)
102 x 193 x 81 mm
Net Weight
0.5 kg
Centre Speaker
6
Type
2 Way 2 speaker
Impedance Rated
3Ω
Input Power
141 W
Max. Input Power
282 W
Net Dimensions (W x H x D)
250 x 100 x 88 mm
Net Weight
0.6 kg
Passive Subwoofer
Appendix
Type
1 Way 1 Speaker
Impedance Rated
3Ω
Input Power
145 W
Max. Input Power
290 W
Net Dimensions (W x H x D)
190 x 385 x 318 mm
Net Weight
5.0 kg
Design and specifications are subject to change
without notice.
HT806PH-D0_BGBRLL_ENG_4756.indd 42
2011-02-15 �� 10:10:57
Warranty 43
Technology with the human touch
GUARANTEE
• LG Electronics U.K. Ltd. will provide the following services in order toexpedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a period
of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the repair of this LG equipment, for a period of 12 months from the
original date of purchase. These claims must be made in accordance with the published scale of service charges and relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made to
the apparatus, or if non standard components are used or if the serial number of the apparatus is removed,
defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a receipted
account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become exhausted
or worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
• REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE SURRENDERED
AT THE TIME GUARANTEE SERVICE IS PROVED.
• Product Registration Card :
It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This
will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should
modifications be necessary.
• To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm
SERIAL NO.*
DATE OF PURCHASE.*
In all cases of difficulty - consult your LG dealer from whom the product was purchased
7
Warranty
MODEL NO.*
LGEUK Website : www.lge.co.uk
( service website : www.lgelectronics.co.uk )
HT806PH-D0_BGBRLL_ENG_4756.indd 43
2011-02-15 �� 10:10:57
HT806PH-D0_BGBRLL_ENG_4756.indd 44
2011-02-15 �� 10:10:57
Download PDF

advertising