LG | HX806TG | LG HX806TG Owner’s Manual

SIMPLE MANUAL
3D Blu-ray™
Home Cinema
Please read this manual carefully before operating
your set and retain it for future reference.
FOR THE WARRANTY TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL.
HX806TG (HX806TG, SH86TG-S/ C, SH95TA-W)
P/NO: MFL67204912
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 1
2011-06-01 �� 9:13:00
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service centre.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 2
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
centre. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
2011-06-01 �� 9:13:01
Getting Started
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive 2004/108/EC,
2006/95/EC, and 2009/125/EC.
European representative :
LG Electronics Service Europe B.V. Veluwezoom
15, 1327 AE Almere, The Netherlands (Tel : +31–
(0)36–547–8888)
Notes on Copyrights
This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
Important Notice for TV colour
system
yy If you have a PAL colour system TV, you will see
just distorted images when using discs or video
contents recorded in NTSC.
yy The multi system colour TV changes the colour
system automatically according to input signals.
In case that the colour system is not changed
automatically, turn it off and then on to see
normal images on screen.
yy Even if the disc recorded in NTSC colour system
are well displayed on your TV, these may not be
recorded correctly on your recorder.
1
Getting Started
2. All electrical and electronic products
shall be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3
POWER: This unit operates on a mains supply of
200-240V~, 50/60Hz.
WIRING: This unit is supplied with a BSI 1363
approved 13 amp mains plug, fused at 5 amp.
When replacing the fuse always use a 5 amp BS
1362, BSI or ASTA approved type. Never use this
plug with the fuse cover omitted. To obtain a
replacement fuse cover contact your dealer. If the
type of plug supplied is not suitable for the mains
sockets in your home, then the plug should be
removed and a suitable type fitted. Please refer to
the wiring instructions below:
WIRING: A mains plug removed from the mains
lead of this unit must be destroyed. A mains plug
with bared wires is hazardous if inserted in a
mains socket. Do not connect either wire to the
earth pin, marked with the letter E or with the
earth symbol or coloured green or green and
yellow. If any other plug is fitted, use a 5 amp fuse,
either in the plug, or at the distribution board.
IMPORTANT: The wires in this mains lead are
coloured in accordance with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours
of the wires in the mains lead of this unit may not
correspond with the coloured marking identifying
the terminals in your plug, proceed as follows: The
wire which is coloured blue must be connected
to the terminal which is marked with the letter
N or coloured black. The wire which is coloured
brown must be connected to the terminal which
is marked with the letter L or coloured red.
The colour system of this player differs according to
currently playing discs.
For example, when the player plays the disc
recorded in the NTSC colour system, the image is
output as an NTSC signal.
Only the multi system colour TV can receive all
signals output from the player.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 3
2011-06-01 �� 9:13:01
4
Getting Started
Supplied Accesorries
Network Software
Update
1
Getting Started
Network update notification
Video cable (1)
Speaker cables (6)
Remote control (1)
Battery (1)
From time to time, performance improvements
and/or additional features or services may be
made available to units that are connected to a
broadband home network. If there is new software
available and the unit is connected to a broadband
home network, the player will inform you about the
update as follows.
Option 1:
1. The update menu will appear on the screen
when you turn on the player.
FM antenna (1)
Owner’s Manual & PC
Software CD
2. Use A/D to select a desired option and then
press ENTER (b).
[OK]
Starts the software update.
[Cancel]
Exits the update menu and
displays it next booting.
[Hide]
Exits the update menu and
it does not appear until next
software is uploaded in the
update server.
Option 2:
If the software update is available from the update
server, the “Software Update” icon appears in the
Home menu. Press blue (B) coloured button to start
the update procedure.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 4
2011-06-01 �� 9:13:02
Table of Contents
Table of Contents
13
13
14
1
Getting Started
4 Operating
2
4
4
4
6
6
Safety Information
– Supplied Accesorries
Network Software Update
– Network update notification
Introduction
– Playable Discs and symbols used in
this manual
– File requirement
Remote control
Front panel
Rear panel
15
15
15
15
16
7
8
9
9
2 Connecting
10
10
11
12
12
Assembling the speaker stand to the
speaker
– Preparation
Positioning the system
Speaker Connection
– Attaching the speakers to the player
3 System Setting
13
16
– Adjust the Setup Settings
– Resolution Setting
– Wired Network Setup
1
General Playback
– Using [HOME] menu
– Playing a Disc
– Playing a file on disc/USB device
– Basic operations for video and audio
content
On-Screen display
2
3
5 Troubleshooting
17
18
18
5
Troubleshooting
– Customer Support
– Open source software notice
4
6 Appendix
19 Trademarks and Licenses
20 Specifications
5
7 Warranty
22 Warranty
6
Settings
To view the Owner's Manual on the CD-ROM
Load the supplied CD-ROM into the CD-ROM drive on your PC. After a while, the web page will open
automatically. (Windows users only)
If the web page does not appear automatically, browse the CD-ROM drive and double-click the "index.
html" file.
To view the Owner's Manual on the CD-ROM, Adobe Acrobat Reader must be installed on your PC. The
"Acrobat Reader" folder on the CD-ROM contains the installation program for Acrobat Reader.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 5
2011-06-01 �� 9:13:02
6
Getting Started
Introduction
1
Playable Discs and symbols used in this manual
Getting Started
Media/Term
Logo
Symbol
e
Description
yy Discs such as movies that can be purchased or
rented.
yy “Blu-ray 3D” discs and “Blu-ray 3D ONLY” discs.
yy BD-R/RE discs that are recorded in BDAV format.
Blu-ray
y
u
i
r
DVD-ROM
yy BD-R/RE discs that contain Movie, Music or
Photo files.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
yy Discs such as movies that can be purchased or
rented.
yy Movie mode and finalized only
yy Supports the dual layer disc also
DVD-R
DVD-RW
DVD+R
DVD+RW
(8 cm, 12 cm)
DVD-RW (VR)
(8 cm, 12 cm)
Audio CD
(8 cm, 12 cm)
CD-R/RW
(8 cm, 12 cm)
Note
–
Caution
–
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 6
o
Finalized AVCHD format
y
u
i
yy DVD±R/RW discs that contain Movie, Music or
Photo files.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
r
VR mode and finalized only
t
Audio CD
y
u
i
yy CD-R/RW discs that contain Movie, Music or
Photo files.
,
>
Indicates special notes and operating features.
yy ISO 9660+JOLIET, UDF and UDF Bridge format
Indicates cautions for preventing possible
damages from abuse.
2011-06-01 �� 9:13:03
Getting Started
7
File requirement
Movie files
Disc,
USB
DLNA
1
File
Extension
Codec Format
Audio Format
Subtitle
“.avi”, “.divx”,
“.mpg”, “.mpeg”,
“.mkv”, “.mp4”,
“.asf”, “.wmv”,
“.m4v” (DRM
free)
DIVX3.xx, DIVX4.xx, DIVX5.xx, DIVX6.xx
(standard playback
only), XVID, MPEG1 SS,
H.264/MPEG-4 AVC,
MPEG2 PS, MPEG2 TS,
VC-1 SM (WMV3)
Dolby Digital,
DTS, MP3,
WMA, AAC,
AC3
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), VobSub
(.sub), SubViewer 1.0 (.sub),
SubViewer 2.0 (.sub/.txt), TMPlayer
(.txt), DVD Subtitle System (.txt)
“.avi”, “.divx”,
“.mpg”, “.mpeg”,
“.mkv”, “.mp4”,
“.asf”, “.wmv”,
DIVX3.xx, DIVX4.xx, DIVX5.xx, DIVX6.xx
(standard playback
only), XVID, MPEG1 SS,
H.264/MPEG-4 AVC,
MPEG2 PS, MPEG2 TS,
VC-1 SM (WMV3)
Dolby Digital,
DTS, MP3,
WMA, AAC,
AC3
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), SubViewer
1.0 (.sub), SubViewer 2.0 (.sub/.
txt), TMPlayer (.txt), DVD Subtitle
System (.txt)
Getting Started
File
Location
Music files
File
Location
File
Extension
Disc,
USB,
DLNA
“mp3”, “.wma”,
“.wav”, “.m4a”
(DRM free)
Sampling Frequency
within 32 - 48 kHz
(WMA), within 16 - 48
kHz (MP3)
Bitrate
within 32 - 192
kbps (WMA), within
32 - 320 kbps (MP3)
Note
Some wav files are
not supported on this
player.
Photo files
File
Location
Disc,
USB,
DLNA
File
Extension
“.jpg”, “.jpeg”,
“.png”,
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 7
Recommanded
Size
Note
Less than 4,000 x 3,000 x 24 bit/pixel Progressive and lossless
Less than 3,000 x 3,000 x 32 bit/pixel compression photo image files
are not supported.
2011-06-01 �� 9:13:03
8
Getting Started
Remote control
1
Getting Started
• • • • • • a • • • • • • • • • • • • c • • • • • •
RADIO&INPUT (P): Changes
input mode.
SPEAKER LEVEL: Sets the sound
level of desired speaker.
MARKER: Marks any point during
playback.
SOUND EFFECT: Selects a sound
effect mode.
1 (POWER): Switches the player
ON or OFF.
B (OPEN/CLOSE): Opens and
closes the disc tray.
SEARCH: Displays or exits the
search menu.
INFO/DISPLAY (m): Displays or
exits On-Screen Display.
HOME (n): Displays or exits the
[Home Menu].
DISC MENU: Accesses menu on a
disc.
• • • • • • b • • • • • •
PRESET(-/+): Selects programme
of Radio.
TUNING (-/+) : Tunes in the
desired radio station.
W/S/A/D (up/ down/ left/
right): Used to navigate on-screen
displays.
ENTER (b): Acknowledges menu
selection.
Battery Installation
BACK (x): Exits the menu or
resumes playback. The resume
play function may not work
depending on the BD-ROM disc.
TITLE/POPUP: Displays the DVD
title menu or BD-ROM’s pop-up
menu, if available.
VOL +/- : Adjusts speaker volume.
OPTICAL: Changes input mode to
optical directly.
MUTE(@): Mute the unit.
Coloured (R, G, Y, B) buttons:
Use to navigate on menus.
RDS: Radio Data System.
PTY: Views the programme type
of the RDS.
PTY SEARCH:
Searches programme type.
MONO/STEREO: Selects mono/
stereo in FM mode.
SLEEP: Sets a certain period of
time after which the unit will
switch to off.
X REC: Records an audio CD.
0-9 numerical buttons: Selects
numbered options in a menu or
inputs letters in the keypad menu.
CLEAR: Removes a mark on the
search menu or a number when
setting the password.
REPEAT (h): Repeats a desired
section or sequence.
?: This button is not available.
• • • • • • d • • • • • •
TV Control Buttons
Z (STOP): Stops playback.
z (PLAY): Starts playback.
Remove the battery cover on the
rear of the Remote Control, and
insert a (size AAA) battery with 4
and 5 matched correctly.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 8
M PAUSE/STEP: Pauses playback
c/v (SCAN): Searches
backward or forward.
C/V (SKIP): Goes to the
next or previous chapter / track /
file.
2011-06-01 �� 9:13:04
Getting Started
9
Front panel
1
Getting Started
a 1/' (POWER) Button
b R (OPEN/CLOSE)
T (PLAY/PAUSE)
I (STOP)
Y/U (SKIP)
FUNC. (Function)
Changes the input source or function.
c PORT.IN
USB Port
d Volume control
Rear panel
a Speakers connectors
e AUX (R/L) IN/VIDEO OUT
b Cooling Fan
f HDMI OUT (Type A, HDMI™ Connector)
Connect to TV with HDMI inputs.
c Antenna Connector
d OPTICAL IN
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 9
g LAN port
2011-06-01 �� 9:13:04
10
Connecting
Assembling the
speaker stand to the
speaker
2
Attach the speakers to the speaker stands by
rotating the screws.
Before connecting the speakers, assemble the
speakers. Please check the items for assembling the
speakers.
Connecting
Preparation
Speaker
Stand
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 10
2011-06-01 �� 9:13:04
B
C
A
Connecting
G
F
A
D
A
A
Positioning the system
E
A
The following illustration shows an example of
positioning the system. Note that the illustrations
Ain these instructions differ from the actual unit for
explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position (A). A B C D E F G
A
A
B
C
A
2
G
F
C
A
A
GB
B
CA A
GA
A
B
A A
A
yy Place the center speaker at a safe distance
from the child’s reach.
Otherwise it may result in the speaker falling
down and causing personal injury and/or
property damage.
Connecting
C
CG
G
A
B A
A A
>>Caution
yy Be careful to make sure children not to put
their hands or any objects into the *speaker
duct.
*Speaker duct: A hole for plentiful bass
sound on speaker cabinet (enclosure).
yy The speakers contain magnetic parts, so
colour irregularity may occur on the CRT
TV screen or PC monitor screen. Please use
the speakers away from the TV screen or PC
monitor screen.
B
B
11
A
A
E
E
A
E
A
D
A
A
E
A ABCD E F G
A
speaker (L)/
A A Front
B Cleft
D
EE F G
A D right
speaker
(R):
C
F
A A B Front
E
G
E
A
Place the front speakers to the sides of the monitor
or screen and as flush with the screen surface as
possible.
E
F G
A AA
B C Center
D E speaker:
Place the center speaker above or below the
monitor or screen.
A A B C D Surround
E F G left speaker (L)/
right speaker (R):
F G
A A B C D E Surround
A
Place these speakers behind your listening position,
E
facing slightly inwards.
A B C D E F Subwoofer:
G
The position of the subwoofer is not so critical,
because low bass sounds are not highly directional.
But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of
the room to reduce the wall reflections.
B C D E F G Unit
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 11
2011-06-01 �� 9:13:05
Connecting
12
Speaker Connection
Attaching the speakers to the
player
Connect the wires hooked up to the speaker to the
unit.
2
Connecting
-- To connect the cable to the unit, press each
plastic finger pad to open the connection
terminals on the unit. Insert the wire and
release the finger pad.
-- Connect the black stripe of each wire to the
terminals marked - (minus) and the other end
to the terminals marked + (plus).
Colour
Speaker
Position
Grey
Rear
Rear right
Blue
Rear
Rear left
Green
Center
Centre
Orange
Sub
woofer
Any front position
Red
Front
Front right
White
Front
Front left
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 12
2011-06-01 �� 9:13:05
System Setting
Settings
Adjust the Setup Settings
You can change the settings of the player in the
[Setup] menu.
1. Press HOME (n).
13
Resolution Setting
The player provides several output resolutions for
HDMI OUT jack. You can change the resolution
using [Setup] menu.
1. Press HOME (n).
2. Use A/D to select the [Setup] and press ENTER
(b). The [Setup] menu appears.
3. Use W/S to select [DISPLAY] option then
press D to move to the second level.
4. Use W/S to select the [Resolution] option
then press ENTER (b) to move to the third level.
3
5. Use W/S to select the desired resolution then
press ENTER (b) to confirm your selection.
,,Note
3. Use W/S to select the first setup option, and
press D to move to the second level.
System Setting
2. Use A/D to select the [Setup] and press ENTER
(b). The [Setup] menu appears.
yy If your TV does not accept the resolution
you have set on the player, you can set
resolution to 576p as follows:
1. Press B to open the disc tray.
2 Press Z (STOP) for more than 5 seconds.
4. Use W/S to select a second setup option, and
press ENTER (b) to move to the third level.
5. Use W/S to select a desired setting, and press
ENTER (b) to confirm your selection.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 13
2011-06-01 �� 9:13:06
14
System Setting
Wired Network Setup
If there is a DHCP server on the local area network
(LAN) via wired connection, this player will
automatically be allocated an IP address. After
making the physical connection, a small number of
home networks may require the player’s network
setting to be adjusted. Adjust the [NETWORK]
setting as follow.
5. The player will ask you to test the network
connection. Select [OK] and press ENTER (b) to
complete the network connection.
6. If you select [Test] and press ENTER (b) at
step 5 above, the network connection status is
displayed on the screen.
You can also test it on the [Connection Status]
in the [Setup] menu.
Preparation
Before setting the wired network, you need to
connect the broadband internet to your home
network.
3
1. Select [Connection Setting] option in the
[Setup] menu then press ENTER (b).
System Setting
2. Select [Yes] and press ENTER (b) to continue.
The new connection settings reset the current
network settings.
3. Use W/S/A/D to select the IP mode
between [Dynamic] and [Static].
Normally, select [Dynamic] to allocate an IP
address automatically.
,,Note
If there is no DHCP server on the network and
you want to set the IP address manually, select
[Static] then set [IP Address], [Subnet Mask],
[Gateway] and [DNS Server] using W/S/
A/D and numerical buttons. If you make a
mistake while entering a number, press CLEAR
to clear the highlighted part.
4. Select [OK] and press ENTER (b) to apply
network settings.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 14
2011-06-01 �� 9:13:07
Operating
15
General Playback
Playing a Disc
ert
Using [HOME] menu
1. Press B (OPEN/CLOSE), and place a disc on the
disc tray.
The home menu appears when you press HOME
(n). Use A/D to select a category and press
ENTER (b).
2. Press B (OPEN/CLOSE) to close the disc tray.
a
b
c
d
e
f
For the most Audio CD, BD-ROM and DVD-ROM discs, playback starts automatically.
3. Press HOME (n).
4. Select [Movie] or [Music] using A/D, and press
ENTER (b).
5. Select [BD], [DVD], [VR] or [Audio] option using W/S, and press ENTER (b).
,,Note
yy Playback functions described in this manual
are not always available in every files and
media. Some functions can be restricted
depending on many factors.
b [Photo] - Plays photo contents.
c [Music] - Plays audio contents.
d [NetCast] - Access to the NetCast Home.
e [Input] - Changes input mode
f [Setup] - Adjusts the system settings.
yy Unfinalized DVD VR format discs may not be
played in this player.
4
Operating
a [Movie] - Plays video contents.
yy Depending on the BD-ROM titles, a USB
device connection may be needed for the
proper playback.
yy Some DVD-VR discs are made with CPRM
data by DVD RECORDER. This unit cannot
support these kinds of discs.
Playing a file on disc/USB
device
yui
This player can play movie, music and photo files
contained in the disc or USB device.
1. Insert a data disc on the tray or connect a USB
device.
2. Select [Movie], [Photo] or [Music] using A/D,
and press ENTER (b).
3. Select [Data] or [USB] option using W/S, and
press ENTER (b).
4. Select a file using W/S/A/D, and press
d(PLAY) or ENTER (b) to play the file.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 15
2011-06-01 �� 9:13:07
16
Operating
Basic operations for video and
audio content
On-Screen display
To stop playback
You can display and adjust various information and
settings about the content.
Press Z (STOP) while playback.
eroy
To pause playback
1. While playback, press INFO/DISPLAY (m) to
show various playback information.
Press M (PAUSE) while playback.
Press d (PLAY) to resume playback.
To play frame-by-frame (Video)
Press M (PAUSE) while movie playback.
Press M (PAUSE) repeatedly to play Frame-by-Frame
playback.
To scan forward or backward
Press c or v to play fast forward or fast reverse
during playback.
4
Operating
You can change the various playback speeds by
pressing c or v repeatedly.
To slow down the playing speed
(Video)
While the playback is paused, press v repeatedly
to play various speeds of slow motion.
a Title – current title number/total number of
titles
b Chapter – current chapter number/total
number of chapters
To skip to the next/previous
chapter/track/file
c Time – elapsed playing time/total playback
time
During playback, press C or V to go to the
next chapter/track/file or to return to the beginning
of the current chapter/track/file.
e Subtitle – selected subtitle.
Press C twice briefly to step back to the previous
chapter/track/file.
In the file list menu of a server, there may have
many types of contents in a folder together. In this
case, press C or V to go to the previous or
next content with same type.
d Audio – selected audio language or channel
f Angle – selected angle/total number of
angles
g TV Aspect Ratio – selected TV aspect Ratio
h Picture Mode – selected picture mode
2. Select an option using W/S.
3. Use A/D to adjust the selected option value.
4. Press BACK(x) to exit the On-Screen display.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 16
2011-06-01 �� 9:13:07
5
Troubleshooting
Troubleshooting
17
Troubleshooting
Symptom
Cause & Solution
The Power does not turned on.
yy Plug the power cord into the wall outlet securely.
The unit does not start
playback.
yy Insert a playable disc. (Check the disc type, colour system, and
regional code.)
yy Place the disc with the playback side down.
yy Place the disc on the disc tray correctly inside the guide.
yy Clean the disc.
yy Cancel the Rating function or change the rating level.
The angle cannot be changed.
yy Multi-angles are not recorded on the DVD Video being played.
Cannot play movie, photo or
music files.
yy The files are not recorded in a format that the unit can play.
The remote control does not
work properly.
yy The remote control is not pointed at the remote sensor of the unit.
yy The unit does not support the codec of the movie file.
yy The remote control is too far from the unit.
yy There is an obstacle in the path of the remote control and the unit.
yy The batteries in the remote control are exhausted.
The unit is plugged in, but the
power will not turn on or off.
There is no picture.
Press and hold the POWER button for at least five seconds. This will force
the unit to power off then turn the unit back on.
yy Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
yy Connect the video connection securely.
yy Check the [HDMI Color Setting] in the [Setup] menu is set to the
appropriate item that conforms to your video connection.
5
Troubleshooting
The unit is not operating
normally.
You can reset the unit as follows.
yy Your TV may not suppot the resolution you have set on the player.
Change the resolution that your TV accepts.
yy The player’s HDMI OUT jack is connected to a DVI device that does
not support copyright protection.
Picture noise appears.
yy You are playing a disc recorded in a colour system that is different
from your TV.
yy Set the resolution which your TV accepts.
Blu-ray 3D disc playback does
not output 3D views.
yy Connect the player to your TV with HDMI cable (Type A, High Speed
HDMI™ Cable).
yy Your TV may not support “HDMI 1.4 3D mandatory format”.
yy The [3D Mode] option in the [Setup] menu is set to [Off ]. Set the option to [On].
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 17
2011-06-01 �� 9:13:07
18
Troubleshooting
Symptom
Cause & Solution
BD-Live feature does not work.
yy The connected USB storage may not have enough space. Connect
the USB storage with at least 1GB free space.
yy Ensure that the unit is correctly connected to the local area network
and can access the internet.
yy Your broadband speed may not fast enough to use the BD-Live
features. Contact your Internet Service Provider (ISP) and increase the
broadband speed is recommended.
yy The [BD-LIVE connection] option in the [Setup] menu is set to
[Prohibited]. Set the option to [Permitted].
Streaming video services (such
as YouTube™, etc.) are often
stopped or “buffer” during
playback.
yy Your broadband service speed may not be fast enough to stream
video services. Contact your Internet Service Provider (ISP) and
increase the broadband speed is recommended.
Shared folder or files from
media server are not displayed
on the device list.
The player is not connected to the local area network that your media
server are connected.
There is no sound or the sound
is distorted.
yy The unit is in scan, slow motion, or pause mode.
yy The sound volume is low.
yy Check the speaker cable connection.
5
Customer Support
Troubleshooting
You can update the Player using the latest software to enhance the products operation and/or add new
features. To obtain the latest software for this player (if updates have been made), please visit http://lgservice.com or contact LG Electronics customer care centre.
Open source software notice
To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit
http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are
available to download with the source code.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 18
2011-06-01 �� 9:13:07
Appendix
19
Trademarks and
Licenses
Blu-ray Disc™, Blu-ray™, Blu-ray 3D™, BD-Live™,
BONUSVIEW™ and the logos are trademarks of
the Blu-ray Disc Association.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,392,195; 7,272,567;
7,333,929; 7,212,872 & other U.S. and worldwide
patents issued & pending. DTS and the Symbol
are registered trademarks,& DTS-HD, DTS-HD
Master Audio | Essential and the DTS logos
are trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks
of the Digital Living Network Alliance.
Java and all Java-based trademarks and logos
are trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and other
countries.
DivX®, DivX Certified® and associated logos
are trademark of DivX, Inc., and are used under
license.
6
Appendix
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
“AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 19
2011-06-01 �� 9:13:08
20 Appendix
Specifications
General
Power requirements
AC 200 - 240 V, 50/ 60 Hz
Power consumption
120 W
Dimensions (W x H x D)
Approx. 360 x 59 x 307 mm without foot
Net Weight (Approx.)
2.8 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Inputs/Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector)
ANALOG AUDIO IN
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL IN (OPTICAL)
Optical Connector x 1
PORT. IN
0.5 Vrms (3.5 mm stereo jack)
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
Power output (3 Ω), (RMS), THD 10 %
6
Appendix
Total
850 W
Front
141 W x 2
Center
141 W
Surround
141 W x 2
Sub-Woofer
145 W (Passive)
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 20
2011-06-01 �� 9:13:08
Appendix
21
System
Laser
Semiconductor laser
Wavelength
405 nm / 650 nm
Signal system
Standard NTSC color TV system
Frequency response
20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Signal-to-noise ratio
More than 80 dB
Total harmonic distortion
0.05 % at 1 W
Dynamic range
More than 85 dB
LAN port
Ethernet jack x 1, 10BASE-T / 100BASE-TX
Bus Power Supply (USB)
DC 5 V 0 500 mA
Speakers
Front speaker (Left/ Right)
Type
2 Way 2 speaker
Max. Input power
282 W
Impedance Rated
3Ω
Net Dimensions (W x H x D)
270 X 1 052 X 225 mm
Input Power
141 W
Net Weight
2.9 kg
2 Way 2 speaker
Max. Input power
282 W
Impedance Rated
3Ω
Net Dimensions (W x H x D)
270 X 1 052 X 225 mm
Input Power
141 W
Net Weight
2.9 kg
2 Way 3 speaker
Max. Input power
282 W
Impedance Rated
3Ω
Net Dimensions (W x H x D)
320 X 103 X 86 mm
Input Power
141 W
Net Weight
1.0 kg
1 Way 1 speaker
Max. Input power
290 W
Impedance Rated
3Ω
Net Dimensions (W x H x D)
190 x 385 x 318 mm
Input Power
145 W
Net Weight
5.0 kg
Rear speaker (Left/ Right)
Type
Center speaker
Type
Type
Appendix
Subwoofer
6
yy Design and specifications are subject to change without notice.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 21
2011-06-01 �� 9:13:08
22 Warranty
Technology with the human touch
GUARANTEE
• LG Electronics U.K. Ltd. will provide the following services in order toexpedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a period
of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the repair of this LG equipment, for a period of 12 months from the
original date of purchase. These claims must be made in accordance with the published scale of service charges and relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made to
the apparatus, or if non standard components are used or if the serial number of the apparatus is removed,
defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a receipted
account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become exhausted
or worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
• REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE SURRENDERED
AT THE TIME GUARANTEE SERVICE IS PROVED.
• Product Registration Card :
It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This
will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should
modifications be necessary.
7
• To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm
Warranty
MODEL NO.*
SERIAL NO.*
DATE OF PURCHASE.*
In all cases of difficulty - consult your LG dealer from whom the product was purchased
LGEUK Website : www.lge.co.uk
( service website : www.lgelectronics.co.uk )
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 22
2011-06-01 �� 9:13:08
An extended Owner's Manual that contains
information on the advanced features is located
on the CD-ROM provided in an electronic version.
To read these files, you will need to use a Personal
Computer (PC) equipped with a CD-ROM drive.
HB806TG-D0_BGBRLL_SIM_ENG_4912.indd 23
2011-06-01 �� 9:13:09
Download PDF

advertising