OWNER’S MANUAL 3D Blu-ray™ HOME CINEMA SYSTEM Please read this manual carefully before operating your set and retain it for future reference. HX46R(HX46R, SB46R-F, SB45R-W) P/NO : SAC35215503 Getting Started 3 Safety Information CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM. CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible. 1 Getting Started RISK OF ELECTRIC SHOCK DO NOT OPEN 4 Getting Started This device is equipped with a portable battery or accumulator. 1 Getting Started Safety way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus. Disposal of your old appliance 1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2.All electrical and electronic products shall be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. LG Electronics hereby declares that this/ these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC and 2009/125/EC. European representative : LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere, The Netherlands (Tel : +31-(0)36-547-8888) Getting Started Notes on Copyrights yy Furthermore, BD-ROM Mark and BD+ are additionally used as content protection systems for BD format, which imposes certain restrictions including playback restrictions for BD-ROM Mark and/or BD+ protected contents. To obtain additional information on AACS, BD-ROM Mark, BD+, or this product, please contact an authorized Customer Service Center. yy Many BD-ROM/DVD discs are encoded with copy protection. Because of this, you should only connect your player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected discs. yy This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi. Reverse engineering or disassembly is prohibited. yy Under the U.S. Copyright laws and Copyright laws of other countries, unauthorized recording, use, display, distribution, or revision of television programs, videotapes, BD-ROM discs, DVDs, CDs and other materials may subject you to civil and/ or criminal liability. Important Notice for TV colour system The colour system of this player differs according to currently playing discs. For example, when the player plays the disc recorded in the NTSC colour system, the image is output as an NTSC signal. Only the multi system colour TV can receive all signals output from the player. yy If you have a PAL colour system TV, you will see just distorted images when using discs or video contents recorded in NTSC. yy The multi system colour TV changes the colour system automatically according to input signals. In case that the colour system is not changed automatically, turn it off and then on to see normal images on screen. yy Even if the disc recorded in NTSC colour system are well displayed on your TV, these may not be recorded correctly on your recorder. 1 Getting Started yy Because AACS (Advanced Access Content System) is approved as content protection system for BD format, similar to use of CSS (Content Scramble System) for DVD format, certain restrictions are imposed on playback, analog signal output, etc., of AACS protected contents. The operation of this product and restrictions on this product may vary depending on your time of purchase as those restrictions may be adopted and/or changed by AACS after the production of this product. 5 6 Table of Contents Table of Contents 1 Getting Started 3 8 8 Safety Information Introduction – Playable Discs and symbols used in this manual – About the “7” Symbol Display – File compatibility – AVCHD (Advanced Video Codec High Definition) – System Select (Optional) –About DLNA – Certain System Requirements – LG Remote – Compatibility Notes – Regional Code Remote control Front panel Rear panel 9 10 11 11 12 12 12 12 12 13 14 14 2 Connecting 15 16 16 17 17 17 18 19 20 20 21 23 23 Speaker Connection Connecting to Your TV – HDMI Connection – What is SIMPLINK? – Video Connection – Resolution Setting Antenna connection Connections with external device Connecting to your Home Network – Wired network connection – Wired Network Setup USB device connection – Playback content in the USB device 27 27 28 29 4 Operating 30 30 30 30 31 31 32 33 33 33 33 34 34 34 35 35 36 36 36 37 37 38 38 38 3 System Setting 39 39 40 40 40 41 41 42 43 24 24 24 26 26 43 43 43 43 Settings – Adjust the Setup Settings – [DISPLAY] Menu – [LANGUAGE] Menu – [AUDIO] Menu – [LOCK] Menu – [NETWORK] Menu – [OTHERS] Menu Sound Effect General Playback – Using [HOME] menu – Playing a Disc – Playing a file on a disc/USB device – Playing Blu-ray 3D disc – Enjoying BD-LiveTM – Playing a file on a network server – Basic operations for video and audio content – Basic operations for photo content – Using the disc menu – Resume playback Advanced Playback – Repeat Playback – Repeating a specific portion – Marker Search – Using the search menu – Changing content list view – Viewing content information – Selecting a subtitle file – Last Scene Memory – Options while viewing a photo – Listening to music while slide show On-Screen display – Displaying content information onscreen – Playing from selected time – Hearing a different audio – Selecting a subtitle language – Watching from a different angle – Changing the TV Aspect Ratio – Changing the Picture Mode – Changing subtitle code page Audio CD Recording Displaying MP3 music information (ID3 Tag) Radio Operations – Listening to the radio – Presetting the Radio Stations – Deleting all the saved stations Table of Contents 44 44 44 44 – Deleting a saved station – Improving poor FM reception – See information about a radio station Enjoying the NetCast™ Entertainment Access 7 1 5 Troubleshooting 45 45 46 46 47 47 47 Troubleshooting – General – Network – Picture – Sound – Customer Support – Open source software notice 2 3 6 Appendix 48 Controlling a TV with the Supplied Remote Control 48 – Setting up the remote to control your TV 49 Network Software Update 49 – Network update notification 49 – Software Update 50 About Nero MediaHome 4 Essentials 50 – Installing Nero MediaHome 4 Essentials 51 – Sharing files and folders 52 Area Code List 53 Language Code List 54 Trademarks and Licenses 55 Video Output Resolution 56 Specifications 58 Maintenance 58 – Handling the Unit 58 – Notes on Discs 59 Important Information Relating to Network Services 4 5 6 8 Getting Started Introduction 1 Playable Discs and symbols used in this manual Getting Started Media/Term Logo Symbol e Description yy Discs such as movies that can be purchased or rented. yy “Blu-ray 3D” discs and “Blu-ray 3D ONLY” discs yy BD-R/RE discs that are recorded in BDAV format. Blu-ray y u i r DVD-ROM yy BD-R/RE discs that contain Movie, Music or Photo files. yy ISO 9660+JOLIET, UDF and UDF Bridge format yy Discs such as movies that can be purchased or rented. yy Video mode and finalized only yy Supports the dual layer disc also DVD-R DVD-RW DVD+R DVD+RW (8 cm / 12 cm disc) o Finalized AVCHD format y u i yy DVD±R/RW discs that contain Movie, Music or Photo files. yy ISO 9660+JOLIET, UDF and UDF Bridge format DVD-RW (VR) (8 cm / 12 cm disc) r Audio CD (8 cm / 12 cm disc) t CD-R/RW (8 cm / 12 cm disc) y u i yy CD-R/RW discs that contain Movie, Music or Photo files. , > Indicates special notes and operating features. VR mode and finalized only Note – Caution – Audio CD yy ISO 9660+JOLIET, UDF and UDF Bridge format Indicates cautions for preventing possible damages from abuse. Getting Started ,,Note yy Depending on the recording software & the finalization, some recorded discs (CD-R/RW, DVD±R/RW, BD-R/RE) may not be playable. yy BD-R/RE, DVD±R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player’s lens. yy If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.) yy This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. yy Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain pre-existing conditions to ensure compatible playback. yy Customers should note that permission is required in order to download MP3/ WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner. yy You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live System, you cannot use it on LG player. (Mastered/Live File System : Disc format system for windows Vista) About the “7” Symbol Display “7” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media. 1 Getting Started yy Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit. 9 10 Getting Started File compatibility Movie files 1 Getting Started File Location Disc, USB DLNA File Extension Codec Format Audio Format Subtitle .avi, .mpg, .mpeg, .mkv, .mp4, .asf, .wmv, .m4v (DRM free) DIVX3.xx, DIVX4xx, DIVX5.xx, XVID, DIVX6. xx (Standard playback only), H.264/MPEG4 AVC, MPEG1 SS, MPEG2 PS, MPEG2 TS Dolby Digital, DTS, MP3, WMA, AAC, AC3 SubRip (.srt/.txt), SAMI (.smi), SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), VobSub (.sub), SubViewer 1.0 (.sub), SubViewer 2.0 (.sub/.txt), TMPlayer (.txt), DVD Subtitle System (.txt) .avi, .divx, .mpg, .mpeg, .mkv, .mp4 DIVX3.xx, DIVX4.xx, DIVX5.xx, DIVX6.xx (Standard playback only), XVID, MPEG1 SS, H.264/MPEG-4 AVC, MPEG2 PS, MPEG2 TS Dolby Digital, DTS, MP3, WMA, AAC, AC3 SubRip (.srt/.txt), SAMI (.smi), SubStation Alpha (.ssa/.txt), MicroDVD (.sub/.txt), SubViewer 1.0 (.sub), SubViewer 2.0 (.sub/. txt), TMPlayer (.txt), DVD Subtitle System (.txt) Music files File Location Disc, USB, DLNA File Extension .mp3, .wma, .wav, .m4a (DRM free) Sampling Frequency Bitrate Note within 32 - 48 kHz (WMA), within 32 - 192 kbps Some WAV files are within 16 - 48 kHz (MP3) (WMA), within not supported on this 32 - 320 kbps (MP3) player. Photo files File Location Disc, USB, DLNA File Extension .jpg, .jpeg, .png Recommanded Size Note Less than 4,000 x 3,000 x 24 bit/pixel Progressive and lossless Less than 3,000 x 3,000 x 32 bit/pixel compression photo image files are not supported. Getting Started ,,Note yy The file name is limited to 180 characters. yy A “avi” file which is encoded “WMV 9 codec” is not supported. yy File compatibility may differ depending on the server. yy Because the compatibility on DLNA server are tested on the bundle DLNA server (Nero MediaHome 4 Essentials) environment, file requirements and playback functions may differ depending on media servers. yy The file requirements on page 10 are not always compatible. There may have some restrictions by file features and media server’s ability. yy Playing a movie subtitle files are only available on DLNA media server created by supplied Nero MediaHome 4 Essentials software on this player package. yy The files from removable media such as USB drive, DVD-drive etc. on your media server may not be shared properly. yy The total playback time of music file indicated on the screen may not correct for VBR files. yy HD video files contained on the CD or USB 1.0/1.1 may not played properly. Blu-ray Disc, DVD or USB 2.0 are recommended to play back HD video files. yy This player supports H.264/MPEG-4 AVC profile Main, High at Level 4.1. For a file with higher level, the warning message will appear on the screen. yy This player does not support files that are recorded with GMC*1 or Qpel*2. ,,Note yy This player supports UTF-8 files even it contains Unicode subtitle contents. This player can not support the pure Unicode subtitle files. yy Depending on the types of file or ways of recording, it may not play back. yy A disc which was recorded by multi-session on normal PC is not supported on this player. yy To be playback a movie file, movie file name and Subtitle file name must be the same. yy If video codec is MPEG2 TS or MPEG2 PS, subtitle does not play back. yy The total playback time of music file indicated on the screen may not correct for VBR files. AVCHD (Advanced Video Codec High Definition) yy This player can playback AVCHD format discs. These discs are normally recorded and used in camcorders. yy The AVCHD format is a high definition digital video camera format. yy The MPEG-4 AVC/H.264 format is capable of compressing images at higher efficiency than that of the conventional image compressing format. yy This player can playback AVCHD discs using “x.v.Color” format. yy Some AVCHD format discs may not play depending on the recording condition. yy AVCHD format discs need to be finalized. yy “x.v.Color” offers a wider color range than normal DVD camcorder discs. System Select (Optional) You must select the appropriate system mode for your TV system. Press B(Open/Close). And don’t remove the disc.Press and hold M(PAUSE) for more than five seconds when displays “OPEN” in display window to be able to select a system.If there is not the disc, insert and release the disc. 1 Getting Started yy Depending on the size and number of the files, it may take several minutes to read the contents on the media. 11 12 Getting Started About DLNA 1 This Player is a DLNA Certified digital media player that can display and play movie, photo and music content from your DLNA-compatible digital media server (PC and Consumer Electronics). Getting Started The Digital Living Network Alliance (DLNA) is a cross-industry organization of consumer electronics, computing industry and mobile device companies. Digital Living provides consumers with easy sharing of digital media through your home network. The DLNA certification logo makes it easy to find products that comply with the DLNA Interoperability Guidelines. This unit complies with DLNA Interoperability Guidelines v1.5. When a PC running DLNA server software or other DLNA compatible device is connected to this player, some setting changes of software or other devices may be required. Please refer to the operating instructions for the software or device for more information. Certain System Requirements For high definition video playback: yy High definition display that has HDMI input jacks. yy BD-ROM disc with high definition content. yy HDMI or HDCP capable DVI input on your display device is required for some content (as specified by disc authors). For Dolby® Digital Plus, Dolby TrueHD and DTS-HD multi-channel audio playback: yy An amplifier/receiver with a built-in (Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD) decoder. yy Main, center, surround speakers and subwoofer as necessary for chosen format. LG Remote You can control this player with your iPhone or Android phone via your home network. This player and your phone must be connected to your wireless network device such as access point. Visit “Apple iTunes” or “Google Apps Marketplace” for detailed information of “LG Remote”. ,,Note “LG Remote” function could be supported through updating the Network Software in the first half of 2011. We recommend update of the player using the latest software to add this feature. (See page 49) Compatibility Notes yy Because BD-ROM is a new format, certain disc, digital connection and other compatibility issues are possible. If you experience compatibility problems, please contact an authorized Customer Service Center. yy This unit allows you to enjoy functions such as picture-in-picture, secondary audio and Virtual packages, etc., with BD-Video supporting BONUSVIEW (BD-ROM version 2 Profile 1 version 1.1/ Final Standard Profile). Secondary video and audio can be played from a disc compatible with the picture-in-picture function. For the playback method, refer to the instructions in the disc. yy Viewing high-definition content and upconverting standard DVD content may require a HDMI-capable input or HDCP-capable DVI input on your display device. yy Some BD-ROM and DVD discs may restrict the use of some operation commands or features. yy Dolby TrueHD, Dolby Digital Plus and DTS-HD are supported with maximum 5.1 channels if you use HDMI connection for the audio output of the unit. yy You can use a USB device to store some discs related information, including downloaded online content. The disc you are using will control how long this information is retained. Regional Code This unit has a regional code printed on the rear of the unit. This unit can play only BD-ROM or DVD discs labeled same as the rear of the unit or “ALL”. Getting Started 13 Remote control W/S/A/D (up/ down/ left/ right): Used to navigate on-screen displays. B (OPEN/CLOSE): Insert or release a disc. PRESET +/-: Selects programme of Radio. RADIO&INPUT: Changes input mode. TUNING +/-: Tunes in the desired radio station. 0-9 numerical buttons: Selects numbered options in a menu or inputs letters in the keypad menu. ENTER (b): Acknowledges menu selection. CLEAR: Removes a mark on the search menu or a number when setting the password. REPEAT (h): Repeats a desired section or sequence. • • • • • • b • • • • • • c/v (SCAN): Searches backward or forward. C/V (SKIP): Goes to the next or previous chapter / track / file. Z (STOP): Stops playback. z (PLAY): Starts playback. M (PAUSE): Pauses playback. SPEAKER LEVEL: Sets the sound level of desired speaker. SOUND EFFECT: Selects a sound effect mode. VOL +/-: Adjusts speaker volume. Battery Installation OPTICAL: Changes input mode to optical directly. MUTE: Mute the unit. • • • • • • c • • • • • • HOME (n): Displays or exits the [Home Menu]. Remove the battery cover on the rear of the Remote Control, and insert two R03 (size AAA) batteries with 4 and 5 matched correctly. INFO/DISPLAY (m): Displays or exits On-Screen Display. BACK (x): Exits the menu or resumes playback. The resume play function may not work depending on the BD-ROM disc. TITLE/POPUP: Displays the DVD title menu or BD-ROM’s pop-up menu, if available. DISC MENU: Accesses menu on a disc. • • • • • • d • • • • • • Colored (R, G, Y, B) buttons: Use to navigate on menus. -B button : Selects mono/stereo in FM mode. RDS: Radio Data System. PTY: Views the programme type of the RDS. PTY SEARCH: Searches programme type. MARKER: Marks any point during playback. SEARCH: Displays or exits the search menu. SLEEP: Sets a certain period of time after which the unit will switch to off. X (REC): Records an audio CD. TV Control Buttons: See page 48 1 Getting Started 1 (POWER): Switches the player ON or OFF. • • • • • • a • • • • • • 14 Getting Started Front panel 3 6 5 4 1 Getting Started 2 7 1 a PORT. IN dDisplay window bUSB Port eRemote Sensor cOperation buttons 1/I (POWER) Button T (PLAY / PAUSE) I (STOP) -/+: Adjusts speaker volume. FUNC. Changes the input source or function. fR (OPEN/CLOSE) g LED light Rear panel 1 2 3 4 6 FM OPTICAL 1 5 6 OPTICAL 2 7 VIDIO OUT 8 9 10 aDisc slot gOPTICAL IN 1/ 2 bAUX (L/R) INPUT h VIDEO OUT cCooling Fan iAntenna Connector dAC Power cordPlug into the power source. j Speakers connectors e HDMI OUT (type A, HDMI™ Connector) Connect to TV with HDMI inputs. f LAN port Connecting 15 Speaker Connection Attaching the speakers to the player Connect the wires hooked up to the speaker to the unit. -- To connect the cable to the unit, press each plastic finger pad to open the connection terminals on the unit. Insert the wire and release the finger pad. Colour Speaker Position Orange Sub woofer Any front position Red Front Front right White Front Front left >>Caution yy Be careful to make sure children not to put their hands or any objects into the *speaker duct. *Speaker duct: A hole for plentiful bass sound on speaker cabinet (enclosure). yy Place the centre speaker at a safe distance from the child’s reach. Otherwise it may result in the speaker falling down and causing personal injury and/ or property damage. yy The speakers contain magnet parts, so color irregularity may occur on the TV screen or PC monitor screen. Please use the speakers far away from either TV screen or PC monitor. Connecting -- Connect the black stripe of each wire to the terminals marked - (minus) and the other end to the terminals marked + (plus). 2 16 Connecting Connecting to Your TV Make one of the following connections, depending on the capabilities of your existing equipment. yy HDMI connection (page 16) yy Video connection (page 17) HDMI Connection If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable (Type A, High Speed HDMITM Cable). Connect the HDMI jack on the player to the HDMI jack on a HDMI compatible TV or monitor. ,,Note 2 Connecting yy Depending on your TV and other equipment you wish to connect, there are various ways you could connect the player. Use only one of the connections described in this manual. yy Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections. yy Do not connect your player via your VCR. The image could be distorted by the copy protection system. FM OPTICAL 1 OPTICAL 2 VIDIO OUT Rear of the unit. Type A, High Speed HDMI™ Cable TV Set the TV’s source to HDMI (refer to TV’s Owner’s manual). Additional Information for HDMI yy When you connect a HDMI or DVI compatible device make sure of the following: -- Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player. -- The connected device’s video input is set correctly for this unit. -- The connected device is compatible with 720 x 576p (480p), 1280 x 720p, 1920 x 1080i or 1920x1080p video input. yy Not all HDCP-compatible HDMI or DVI devices will work with this player. -- The picture will not be displayed properly with non-HDCP device. -- This player does not playback and TV screen is changed to black screen. Connecting ,,Note yy If a connected HDMI device does not accept the audio output of the player, the HDMI device’s audio sound may be distorted or may not output. yy When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution Setting” on page 17.) yy Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again. Video Connection Connect the VIDEO OUT jack on the player to the video in jack on the TV using a video cable. You can hear the sound through the system’s speakers. OPTICAL 1 OPTICAL 2 VIDIO OUT Rear of the unit. Yellow yy When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable. yy If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m(15 ft.)). What is SIMPLINK? Some functions of this unit are controlled by the TV’s remote control when this unit and LG TV’s with SIMPLINK are connected through HDMI connection. Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc. Refer to the TV owner’s manual for the details of SIMPLINK function. LG TV’s with SIMPLINK function has the logo as shown above. ,,Note Depending on the disc type or playing status, some SIMPLINK operation may differ from your purpose or not work. TV Resolution Setting The player provides several output resolutions for HDMI OUT. You can change the resolution using [Setup] menu. 1. Press HOME (n). 2. Use A/D to select the [Setup] and press ENTER (b). The [Setup] menu appears. 3. Use W/S to select [DISPLAY] option then press D to move to the second level. 2 Connecting yy Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Setup] menu (see page 25). 17 18 Connecting 4. Use W/S to select the [Resolution] option then press ENTER (b) to move to the third level. Antenna connection Connect the supplied antenna for listening to the radio. 2 Connecting 5. Use W/S to select the desired resolution then press ENTER (b) to confirm your selection. ,,Note FM yy If your TV does not accept the resolution you have set on the player, you can set resolution to 576p (or 480p) as follows: FM OPTICAL 1 yy Press Z (STOP) for more than 5 seconds. yy When you set the resolution to 576i (or 480i) with HDMI connection, actual resolution is outputted to 576p (or 480p). yy If you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto]. yy If you select a resolution that your TV does not accept, the warning message will appear. After resolution change, if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution. yy The 1080p video output frame rate may be automatically set to either 24 Hz or 50 Hz depending both on the capability and preference of the connected TV and based on the native video frame rate of the content on the BD-ROM disc. yy The resolution of the VIDEO OUT jack is always outputted at 576i (or 480i) resolution. OPTICAL 2 VIDIO OUT Rear of the unit. ,,Note yy After connecting the FM wire antenna, keep it as horizontal as possible. Be sure to fully extend the FM wire antenna. Connecting Connections with external device AUX Connection You can enjoy the sound of your component with the analogue audio output jacks from the speakers of the system. 19 PORT. IN Connection You can enjoy the sound of your portable audio player from the speakers of the system. Connect the headphones (or line out ) jack of the portable audio player into the PORT. IN of this unit. And then select the [PORTABLE] option by pressing RADIO&INPUT(P) and ENTER (b). You can also use FUNC. button on the front panel to select the input mode. You can also use FUNC. button on the front panel to select the input mode. MP3 player, etc ... OPTICAL 1 OPTICAL 2 VIDIO OUT Rear of the unit. Red White To the audio output jacks of your component (TV, VCR, etc.) 2 Connecting Connect the analogue audio output jacks of your component into the AUX R/L (INPUT) on this unit. And then select the [AUX] option by pressing RADIO&INPUT (P) and ENTER (b). 20 Connecting OPTICAL IN Connection You can enjoy the sound of your component with the digital optical connection from the speakers of the system. 2 Connect the optical output jack of your component into the OPTICAL IN1/2 jacks on the unit. And then select the [OPTICAL IN1/2] option by pressing RADIO&INPUT(P) and ENTER (b) Or press OPTICAL to select directly. Connecting You can also use FUNC. button on the front panel to select the input mode. OPTICAL 1 OPTICAL 2 VIDIO OUT Rear of the unit. Connecting to your Home Network This player can be connected to a local area network (LAN) via the LAN port on the rear panel. By connecting the unit to a broadband home network, you have access to services such as software updates, BD-Live interactivity and streaming services. Wired network connection Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference. Please refer to the documentation for your network device for further instructions. Connect the player’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable. To the digital optical output jack of your component Connecting ,,Note yy When plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock. yy Do not connect a modular phone cable to the LAN port. yy If you want to access content from DLNA servers, this player must be connected to the same local area network with them via a router. Wired Network Setup If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow. Preparation Before setting the wired network, you need to connect the broadband internet to your home network. 1. Select [Connection Setting] option in the [Setup] menu then press ENTER (b). Router Broadband Service WAN LAN 1 2. Select [Yes] and press ENTER (b) to continue. The new connection settings reset the current network settings. PC PC LAN 2 Router 3. Use W/S/A/D to select the IP mode between [Dynamic] and [Static]. LAN 3 Normally, select [Dynamic] to allocate an IP address automatically. DLNA certified server OPTICAL 1 OPTICAL 2 VIDIO OUT Rear of the unit. ,,Note If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using W/S/ A/D and numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part. 4. Select [OK] and press ENTER (b) to apply network settings. 5. The player will ask you to test the network 2 Connecting yy Since there are various connection configurations, please follow the specifications of your telecommunication carrier or internet service provider. 21 22 Connecting connection. Select [OK] and press ENTER (b) to complete the network connection. 6. If you select [Test] and press ENTER (b) at step 5 above, the network connection status is displayed on the screen. You can also test it on the [Connection Status] in the [Setup] menu. 2 be possible due to certain restrictions set by the Internet service provider (ISP) supplying your broadband Internet connection. yy Any fees charged by an ISP including, without limitation, connection charges are your responsibility. Connecting yy A 10 Base-T or 100 Base-TX LAN port is required for wired connection to this player. If your internet service does not allow for such a connection, you will not be able to connect the player. yy You must use a Router to use xDSL service. Notes on Network Connection: yy Many network connection problems during set up can often be fixed by re-setting the router or modem. After connecting the player to the home network, quickly power off and/ or disconnect the power cable of the home network router or cable modem. Then power on and/or connect the power cable again. yy Depending on the internet service provider (ISP), the number of devices that can receive internet service may be limited by the applicable terms of service. For details, contact your ISP. yy Our company is not responsible for any malfunction of the player and/or the internet connection feature due to communication errors/malfunctions associated with your broadband internet connection, or other connected equipment. yy The features of BD-ROM discs made available through the Internet Connection feature are not created or provided by our company, and our company is not responsible for their functionality or continued availability. Some disc related material available by the Internet Connection may not be compatible with this player. If you have questions about such content, please contact the producer of the disc. yy Some internet contents may require a higher bandwidth connection. yy Even if the player is properly connected and configured, some internet contents may not operate properly because of internet congestion, the quality or bandwidth of your internet service, or problems at the provider of the content. yy Some internet connection operations may not yy A DSL modem is required to use DSL service and a cable modem is required to use cable modem service. Depending on the access method of and subscriber agreement with your ISP, you may not be able to use the internet connection feature contained in this player or you may be limited to the number of devices you can connect at the same time. (If your ISP limits subscription to one device, this player may not be allowed to connect when a PC is already connected.) yy The use of a “Router” may not be allowed or its usage may be limited depending on the policies and restrictions of your ISP. For details, contact your ISP directly. Connecting 23 USB device connection This player can play movie, music and photo files contained in the USB device. Playback content in the USB device 1. Insert a USB device to the USB port until it fits into place. ,,Note yy This player supports USB flash drive/ external HDD formatted in FAT16, FAT32 and NTFS when accessing files (music, photo, movie). However, for BD-Live and Audio CD recording, only FAT16 and FAT32 formats are supported. Use the USB flash drive/ external HDD formatted in either FAT16 or FAT32 when using BD-Live and Audio CD recording. yy This unit can support up to 4 partitions of the USB device. yy Do not extract the USB device during operation (play, etc.). When you connect the USB device on the HOME menu, the player plays a music file contained in the USB storage device automatically. If the USB storage device is containing various types of files, a menu for the file type selection will appear. File loading may takes few minutes depending on the number of content stored in the USB storage device. Press ENTER (b) while [Cancel] is selected to stop loading. 2. Press HOME (n). 3. Select [Movie], [Photo] or [Music] using A/D, and press ENTER (b). 4. Select the [USB] option using W/S, and press ENTER (b). yy A USB device which requires additional program installation when you have connected it to a computer, is not supported. yy USB device: USB device that supports USB1.1 and USB2.0. yy Movie, music and photo files can be played. For details of operations on each file, refer to relevant pages. yy Regular back up is recommended to prevent data loss. yy If you use a USB extension cable, USB HUB or USB Multi-reader, the USB device may not be recognized. yy Some USB device may not work with this unit. yy Digital camera and mobile phone are not supported. yy USB Port of the unit cannot be connected to PC. The unit cannot be used as a storage device. 5. Select a file using W/S/A/D, and press PLAY or ENTER (b) to play the file. 6. Withdraw the USB device carefully. 2 Connecting yy The USB device can be used for the local storage for enjoying BD-Live discs with Internet. 24 System Setting Settings [DISPLAY] Menu TV Aspect Ratio Adjust the Setup Settings You can change the settings of the player in the [Setup] menu. 1. Press HOME (n). Select a TV aspect ratio option according to your TV type. [4:3 Letter Box] Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars above and below the picture. [4:3 Pan Scan] 3 System Setting 2. Use A/D to select the [Setup] and press ENTER (b). The [Setup] menu appears. Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Both sides of the picture are cut off. [16:9 Original] Select when a 16:9 wide TV is connected. The 4:3 picture is displayed with an original 4:3 aspect ratio, with black bars appearing at the left and right sides. [16:9 Full] 3. Use W/S to select the first setup option, and press D to move to the second level. Select when a 16:9 wide TV is connected. The 4:3 picture is adjusted horizontally (in a linear proportion) to fill the entire screen. ,,Note You cannot select [4:3 Letter Box] and [4:3 Pan Scan] option when the resolution is set to higher than 720p. 4. Use W/S to select a second setup option, and press ENTER (b) to move to the third level. 5. Use W/S to select a desired setting, and press ENTER (b) to confirm your selection. 25 Resolution HDMI Color Setting Sets the output resolution HDMI video signal. Refer to page 17 - 18 for details about the resolution setting. Select the type of output from the HDMI OUT jack. For this setting, please refer to the manuals of your display device. [Auto] If the HDMI OUT jack is connected to TVs providing display information (EDID), automatically selects the resolution best suited to the connected TV. [YCbCr] [1080p] Select when connecting to a DVI display device. Outputs 1080 lines of progressive video. [1080i] Outputs 1080 lines of interlaced video. [720p] [576p (or 480p)] [RGB] 3D Mode Select the type of output mode for Blu-ray 3D disc playback. [Off] Outputs 576 (or 480) lines of progressive video. Blu-ray 3D disc playback will output as 2D mode like a normal BD-ROM disc playback. [576i (or 480i)] [On] Outputs 576 (or 480) lines of interlaced video. Blu-ray 3D disc playback will output as 3D mode. 1080p Display Mode When the resolution is set to 1080p, select [24 Hz] for smooth presentation of film material (1080p/24 Hz) with a HDMI-equipped display compatible with 1080p/24 Hz input. ,,Note yy When you select [24 Hz], you may experience some picture disturbance when the video switches video and film material. In this case, select [50 Hz]. yy Even when [1080p Display Mode] is set to [24 Hz], if your TV is not compatible with 1080p/24 Hz, the actual frame frequency of the video output will be 50 Hz to match the video source format. Wallpaper Changes the background of the initial screen. 3 System Setting Outputs 720 lines of progressive video. Select when connecting to a HDMI display device. 26 System Setting [LANGUAGE] Menu Display Menu Select a language for the [Setup] menu and onscreen display. Disc Menu/Disc Audio/ Disc Subtitle Select the language you prefer for the audio track (disc audio), subtitles, and the disc menu. [Original] 3 Refers to the original language in which the disc was recorded. [OK] Confirms the setting. [Cancel] Cancels the setting. HD AV Sync Sometimes Digital TV encounters a delay between picture and sound. If this happens you can compensate by setting a delay on the sound so that it effectively ‘waits’ for the picture to arrive: this is called HD AV Sync. Use WS to scroll up and down through the delay amount, which you can set at anything between 0 and 300 ms. System Setting [Other] Press ENTER (b) to select another language. Use number buttons then press ENTER (b) to enter the corresponding 4-digit number according to the language code list on 53. [Off] (Disc Subtitle only) Turn off Subtitle. ,,Note Depending on the disc, your language setting may not work. DRC (Dynamic Range Control) This function allows you to listen to a movie at a lower volume without losing clarity of sound. [Off] [AUDIO] Menu Speaker Setup To obtain the best possible sound, use the speaker setup display to specify the volume of the speakers you have connected and their distance from your listening position. Use the test to adjust the volume of the speakers to the same level. [Speaker] Select a speaker that you want to adjust. [Volume] Adjust the output level of each speaker. [Distance] Adjust the distance between each speaker and the listening position. [Test/ Stop test tone] The speakers will emit a test tone. Turns off this function. [On] Compress the dynamic range of the Dolby Digital, Dolby Digital Plus or Dolby TrueHD audio output. [Auto] The dynamic range of the Dolby TrueHD audio output is specified by itself. And the dynamic range of the Dolby Digital and Dolby Digital Plus are operated as same as the [On] mode. ,,Note The DRC setting can be changed only when a disc is not inserted or the unit is in complete stop mode. System Setting 27 [LOCK] Menu The [LOCK] settings affect only Blu-ray Disc and DVD playback. To access the any features in [LOCK] settings, you must enter the 4-digit security code you have created. If you have not entered a password yet, you are prompted to do so. Enter a 4-digit password twice, and press ENTER (b) to create a new password.  All BD-ROM can be played. [0-254] Prohibits play of BD-ROM with corresponding ratings recorded on them. ,,Note The [BD Rating] will be applied only for the BD that containing the Advanced Rating Control. Password You can create or change the password. [None] [Change] Enter the current password and press ENTER (b). Enter a 4-digit password twice, and press ENTER (b) to create a new password. Enter the code of the area whose standards were used to rate the DVD video disc, based on the list on page 52. [NETWORK] Menu The [NETWORK] settings are needed to use the software update, BD Live and NetCast features. If you forget your password Connection Setting If you forget your password, you can clear it using the following steps. If your home network environment is ready to connect the player, the player needs to be set the wired network connection for network communication. (See “Connecting to your Home Network” on page20.) 1. Remove any disc that might be in the player. 2. Select [Password] option in the [Setup] menu. 3. Use Number buttons to enter “210499”. The password is cleared. ,,Note If you make a mistake before pressing ENTER (b), press CLEAR. Then input the correct password. Connection Status If you want to check the network status on this player, select the [Connection Status] options and press ENTER (b) to check whether a connection to the network and the internet have been established. DVD Rating BD-LIVE connection Blocks playback of rated DVD based on their content. (Not all discs are rated.) You can restrict Internet access when BD-Live functions are used. [Rating 1-8] [Permitted] Rating one (1) has the most restrictions and rating eight (8) is the least restrictive. Internet access is permitted for all BD-Live contents. [Unlock] [Partially permitted] If you select [Unlock], parental control is not active and the disc plays in full. Internet access is permitted only for BDLive contents which have content owner certificates. Internet access and AACS Online functions are prohibited for all BD-Live contents without a certificate. BD Rating Set an age limit of BD-ROM play. Use number buttons to input an age limit for BD-ROM viewing. 3 System Setting Enter a 4-digit password twice, and press ENTER (b) to create a new password. Area Code 28 System Setting [Prohibited] Internet access is prohibited for all BD-Live contents. NetCast [Country Setting] Select your area for displaying proper services and contents on the [NetCast] feature. 3 Auto Power Off The screen saver appears when you leave the player in Stop mode for about five minutes. If you set this option to [On], the unit automatically turns itself off after the Screen Saver is displayed for 20 minutes. Set this option to [Off ] to leave the screen saver until the unit is operated by the user. Initialize [Factory Set] System Setting [OTHERS] Menu You can reset the player to its original factory settings. DivX® VOD [BD Storage Clear] ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, Inc. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video. Initializes the BD contents from the connected USB storage. ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration. [Register] Displays the registration code of your player. [Deregister] Deactivate your player and display the deactivation code. ,,Note All the downloaded videos from DivX VOD with this player’s registration code can only be played back on this unit. ,,Note If you reset the player to its original factory settings using [Factory Set] option, you have to set all the activation for the on-line services and network settings again. Software [Information] Displays the current software version. [Update] You can update the software by connecting the unit directly to the software update server (see 49). Disclaimer Notice Press ENTER (b) to view the notice of Network Service Disclaimer on 59. System Setting 29 Sound Effect You can select a suitable sound mode. Press SOUND EFFECT repeatedly until the desired mode appears on the front panel display or the TV screen. The displayed items for the equalizer maybe diff erent depending on sound sources and effects. [NATURAL]: You can enjoy comfortable and natural sound. [Bypass]: Software with multichannel surround audio signals is played according to the way it was recorded. [BASS BLAST]: Reinforce the bass sound effect from front left and right speaker and subwoofer. [Loudness]: Improves bass and treble sound. [User EQ]: You can adjust the sound by raising or lowering the level of specific frequency. Setting the [User EQ] 1. Use W/S to select the desired frequency. 2. Use A/D to select the desired level. Select [Cancel] option then press ENTER (b) to cancel the setting. Select [Reset] option then press ENTER (b) to reset the all adjustments. [Clear Voice]: This mode makes voice sound clear, improving the quality of voice sound. [Virtual]: You can enjoy more dynamic sound with improved center channel. [Game]: You can enjoy more virtual sound while playing video games. [Night]: This may be useful when you want to watch movies at low volumes late at night. 3 System Setting [Up scaler]: When listening to MP3 files or other compressed music, you can enhance the sound. This mode is available only to 2 channel sources. 30 Operating ,,Note General Playback Using [HOME] menu yy Playback functions described in this manual are not always available in every file and media. Some functions can be restricted depending on many factors. The home menu appears when you press HOME (n). Use A/D to select a category and press ENTER (b). yy Depending on the BD-ROM titles, a USB device connection may be needed for the proper playback. a b c d e f yy Unfinalized DVD VR format discs may not be played in this player. yy Some DVD-VR discs are made with CPRM data by DVD RECORDER. This unit cannot support these kinds of discs. Playing a file on a disc/USB device yui 4 Operating a [Movie] - Plays video contents. b [Photo] - Plays photo contents. c [Music] - Plays audio contents. d [NetCast] - Access to the NetCast Home. e [Input] - Changes input mode f [Setup] - Adjusts the system settings. Playing a Disc ert 1. Put a disc with the label facing front to the disc slot as below. Then it is automatically inserted. 2 For the most Audio CD, BD-ROM and DVD-ROM discs, playback starts automatically. 3. Press HOME (n). 4. Select [Movie] or [Music] using A/D, and press ENTER (b). 5. Select [BD], [DVD], [VR] or [Audio] option using W/S, and press ENTER (b). ,,Note When a disc is in the unit and the power is ON ,playback is not started automatically. This player can play video, audio and photo files contained in the disc or USB device. 1. Press HOME (n). 2. Select [Movie], [Photo] or [Music] using A/D, and press ENTER (b). 3. Select [Data] or [USB] option using W/S, and press ENTER (b). 4. Select a file using W/S/A/D, and press d (PLAY) or ENTER (b) to play the file. Operating 31 Playing Blu-ray 3D disc e Enjoying BD-LiveTM e This player can play the Blu-ray 3D discs which contains separate views for the left and right eyes. BD-Video supporting BD-Live (BD-ROM version 2 Profile 2) that has a network extension function allows you to enjoy more functions such as downloading new movie trailers by connecting this unit to the internet. Preparation In order to playback Blu-ray 3D title in stereoscopic 3D mode, you need to: heck your TV is 3D capable and has HDMI yy C 1.4 input(s). ear 3D glasses to enjoy the 3D experience yy W if it is necessary. heck whether the BD-ROM title is the Bluyy C ray 3D disc or not. onnect an HDMI cable (Type A, High yy C Speed HDMITM Cable) between the player’s HDMI output and TV’s HDMI input. 2. Put a disc with the label facing front to the disc slot as below. The playback starts automatically. 3. Refer to the owner’s manual of your 3D-ready TV for the further instruction. You may need to adjust the display settings and focus on your TV’s setting for the improved 3D effect. >>Caution yy Watching a 3D content for a long period time may cause dizziness or tiredness. yy It is not recommended to watch a movie in 3D mode for infirm, child and pregnant woman. yy If you are experiencing headache, tiredness or dizziness while viewing contents in 3D, it is strongly recommended to stop the playback and rest until you feel normal. 2. Insert a USB storage device to the USB port on the front panel. A USB storage device is needed to download bonus content. 3. Press HOME (n), and set the [BD-LIVE connection] option on the [Setup] menu (page 27). Depending on a disc, the BD-Live function may not be operated if [BD-LIVE connection] option is set to [Partially Permitted]. 4. Insert a BD-ROM with BD-Live. The operations are differ depending on the disc. Refer to the manual supplied with the disc. >>Caution Do not extract the connected USB device while content is being downloaded or a Bluray disc is still. Doing so may damage the connected USB device and BD-Live features may not operate properly with the damaged USB device anymore. If the connected USB device seems damaged from such an action, you can format the connected USB device from the PC and reuse it with this player. ,,Note yy Some BD-Live contents may be restrictively accessed in some territories by contents provider’s own decision. yy It may take up to several minutes to load and start enjoying BD-Live contents. 4 Operating 1. Press HOME (n), and set the [3D Mode] option on the [Setup] menu to [On] (page 25). 1. Check the network connection and settings (page 20). 32 Operating Playing a file on a network server yui This player can play video, audio and photo files located in a DLNA server through your home network. 1. Check the network connection and settings (page 20). 2. Press HOME (n). 3. Select [Movie], [Photo] or [Music] using A/D, and press ENTER (b). 4. Select a DLNA media server or a share folder on your PC on the list using W/S, and press ENTER (b). 4 Operating If you want to rescan available media server, press the green (G) colored button. 5. Select a file using W/S/A/D, and press ENTER (b) to play the file. ,,Note yy The file requirements are described on page 10. yy The thumbnail of the unplayable files can be displayed, but those cannot be played on this player. yy The subtitle file name and movie file name have to be the same and located at the same folder. yy The playback and operating quality may be affected by your home network condition. yy You may experience connection problems depending on your server’s environment. Operating 33 Basic operations for video and audio content Basic operations for photo content To stop playback To play a slide show Press Z (STOP) while playback. Press d (PLAY) to start slide show. To pause playback To stop a slide show Press M (PAUSE) while playback. Press d (PLAY) to resume playback. Press Z (STOP) while slide show. To play frame-by-frame (Video) Press M (PAUSE) while movie playback. Press M (PAUSE) repeatedly to play Frame-by-Frame playback. To scan forward or backward Press c or v to play fast forward or fast reverse during playback. To slow down the playing speed (Video) While the playback is paused, press v repeatedly to play various speeds of slow motion. To skip to the next/previous chapter/track/file During playback, press C or V to go to the next chapter/track/file or to return to the beginning of the current chapter/track/file. Press C twice briefly to step back to the previous chapter/track/file. In the file list menu of a server, there may have many types of contents in a folder together. In this case, press C or V to go to the previous or next content with same type. Press M (PAUSE) while slide show. Press d (PLAY) to re-start the slide show. To skip to the next/previous photo While viewing a photo in full screen, press A or D to go to the previous or next photo. Using the disc menu ero To display the disc menu The menu screen may be displayed first after loading a disc which contains a menu. If you want to display the disc menu while playback, press DISC MENU. Use W/S/A/D buttons to navigate through menu items. To display the Pop-up menu Some BD-ROM discs contain Pop-up menu that appears while playback. Press TITLE/POPUP while playback, and use W/S/ A/D buttons to navigate through menu items. Resume playback eroyt u The unit records the point where you pressed the Z (STOP) depending on the disc. If “MZ (Resume Stop)” appears on the screen briefly, press d (PLAY) to resume playback (from the scene point). If you press Z (STOP) twice or unload the disc, “Z(Complete Stop)” appears on the screen. The unit will clear the stopped point. 4 Operating You can change the various playback speeds by pressing c or v repeatedly. To pause a slide show 34 Operating ,,Note yy The resume point may be cleared when a button is pressed (for example; 1 (POWER), B (OPEN/CLOSE), etc). yy On BD-Video discs with BD-J, the resume playback function does not work. yy If you press Z (STOP) once during BD-ROM interactive title playback, the unit will be in Complete Stop mode. 4 ,,Note yy If you press V once during Repeat Chapter/ Track playback, the repeat playback cancels. yy This function may not work on some disc or title. Repeating a specific portion erot Advanced Playback This player can repeat a portion you have selected. Repeat Playback erotu y 2. Press ENTER (b) at the end of the portion. Your selected portion will be repeated continually. During playback, press REPEAT (h) repeatedly to select a desired repeat mode. Operating Blu-ray discs/DVDs/ MOVIE jA- – Selected portion will be repeated continually. jChapter – The current chapter will be played back repeatedly. jTitle – The current title will be played back repeatedly. jAll – All the tracks or files will be played back repeatedly. To return to normal playback, press REPEAT (h) repeatedly to select [Off ]. Audio CDs/Audio files kA-B – Selected portion will be repeated continually. (Audio CD only) ;Track– The current track or file will be played back repeatedly. :All – All the tracks or files will be played back repeatedly. l:All – All the tracks or files will be played back repeatedly in random order. l – The tracks or files will be played back in random order. To return to normal playback, press CLEAR. 1. While playback, press REPEAT (h) to select [A-] at the beginning of the portion you wish to repeat. 3. To return to normal playback, press REPEAT (h) repeatedly to select [Off ]. ,,Note yy You cannot select a portion less than 3 seconds. yy This function may not work on some discs or titles. Operating 35 Marker Search eroy Using the search menu eroy You can start playback from up to nine memorized points. Using search menu, you can easily to find the point where you want to start playback. To enter a marker To search a point 1. While playback, press MARKER at the desired point. The Marker icon appears on the TV screen briefly. 1. During playback, press SEARCH to display the search menu. 2. Repeat step 1 to add up to nine markers. To recall a marked scene 1. Press SEARCH and the search menu appears on the screen. 2. Press a number button to select a marker number that you want to recall. Playback starts from the marked scene. To delete a Marker 2. Press S to highlight a marker number. Use A/D to select a marked scene that you want to delete. 3. Press CLEAR and the marked scene is erased from the search menu. ,,Note yy This function may not work depending on discs, titles, server ability. yy All marked points are cleared if the title is in complete stop (Z) mode, the title is changed or if you unload the disc. yy If the total length of the title is less than 10 seconds, this function is not available. To start playback from a marked scene 1. Press SEARCH and the search menu appears on the screen. 2. Press S to highlight a marker number. Use A/ D to select a marked scene that you want to start playback. 3. Press ENTER (b) to start playback from the marked scene. ,,Note yy This function may not work depending on discs, titles, server ability. yy This function may not work depending on the file type and ability of the media server. 4 Operating 1. Press SEARCH and the search menu appears on the screen. 2. Press A/D to skip the playback 15 seconds forward or backward. You can select a point that you want to skip by pressing and holding A/ D button. 36 Operating Changing content list view yui Viewing content information y On the [Movie], [Music] or [Photo] menu, you can change the content list view. The player can display the content information. Method 1 2. Press INFO/DISPLAY (m) to display the option menu. Press red (R) colored button repeatedly. 1. Select a file using W/S/A/D. 3. Select the [Information] option using W/S, and press ENTER (b). The file information appears on the screen. While movie playback, you can display the file information by pressing TITLE/POPUP. ,,Note The information displayed on the screen may not correct comparing actual content information. Selecting a subtitle file y 4 Operating If the subtitle file name is different from the movie file name, you need to select the subtitle file on the [Movie] menu before playing the movie. 1. Use W/S/A/D to select the subtitle file you wish to play in the [Movie] menu. 2. Press ENTER (b). Method 2 1. On the content list, press INFO/DISPLAY (m) to display the option menu. 2. Use W/S to select the [View Change] option. 3. Press ENTER (b) to change the content list view. Press ENTER (b) again to deselect the subtitle file. Selected subtitle file will be displayed when you play the movie file. ,,Note yy If you press Z (STOP) while playback, the subtitle selection is cancelled. yy This function is not available for playing file on a server via home network. Operating 37 Last Scene Memory er Options while viewing a photo i This unit memorizes the last scene from the last disc that is viewed. The last scene remains in memory even if you remove the disc from the unit or switch off the unit. If you load a disc that has the scene memorized, the scene is automatically recalled. You can use various options during viewing a photo in full screen. ,,Note 1. While viewing a photo in full screen, press INFO/ DISPLAY (m) to display the option menu. 2. Select an option using W/S. yy Last Scene Memory function for a previous disc is erased once a different disc is played. yy This function may not work depending on the disc. yy On BD-Video discs with BD-J, the last scene memory function does not work. yy This unit does not memorize settings of a disc if you switch off the unit before commencing to play it. b Slide Show – Press ENTER (b) to start or pause slide show. c Music Select – Select the background music for the slide show (page 38). d Music –Press ENTER (b) to start or pause background music. e Rotate – Press ENTER (b) to rotate the photo clockwise. f Zoom – Press ENTER (b) to display the [Zoom] menu. g Effect – Use A/D to select a transition effect between photos in a slide show. h Speed – Use A/D to select a delaying speed between photos in a slide show. 3. Press BACK (x) to exit the option menu. 4 Operating a Current photo/Total number of photos – Use A/D to view previous/next photo. 38 Operating Listening to music while slide show i You can display photo files while listening to audio files. 1. While viewing a photo in full screen, press INFO/ DISPLAY (m) to display the option menu. 2. Use W/S to select [Music Select] option, and press ENTER (b) to display the [Music Select] menu. 3. Use W/S to select a device, and press ENTER (b). On-Screen display You can display and adjust various information and settings about the content. Displaying content information on-screen eroy 1. While playback, press INFO/DISPLAY (m) to show various playback information. Device that you can select are differ depending on the location of the photo file you are displaying in full screen. 4 Photo location Available Device Disc, USB Disc, USB DLNA server DLNA server Operating 4. Use W/S to select a file or a folder you wish to play. a Title – current title number/total number of titles b Chapter – current chapter number/total number of chapters Select g and press ENTER (b) to display the upper directory. c Time – elapsed playing time/total playback time ,,Note e Subtitle – selected subtitle. When selecting music file from a server, folder selection is not available. Only file selection is available. 5. Use D to select [OK], and press ENTER (b) to complete music selection. d Audio – selected audio language or channel f Angle – selected angle/total number of angles g TV Aspect Ratio – selected TV aspect Ratio h Picture Mode – selected picture mode 2. Select an option using W/S. 3. Use A/D to adjust the selected option value. 4. Press BACK(x) to exit the On-Screen display. Operating 39 ,,Note yy If no button is pressed for a few seconds, the on-screen display disappears. Hearing a different audio eroy yy A title number cannot be selected on some discs. 1. During playback, press INFO/DISPLAY (m) to display the On-Screen display. yy Available items may differ depending on discs or titles. 2. Use W/S to select the [Audio] option. yy If BD interactive title is playing back, some setting information is displayed on the screen but prohibited to be changed. Playing from selected time eroy 1. Press INFO/DISPLAY (m) during playback. The time search box shows the elapsed playing time. For example, to find a scene at 2 hours, 10 minutes, and 20 seconds, enter “21020”. Press A/D to skip the playback 60 seconds forward or backward. 3. Press ENTER (b) to start playback from selected time. ,,Note yy This function may not work on some disc or titles. yy This function may not work depending on the file type and ability of the DLNA server. ,,Note yy Some discs allow you to change audio selections only via the disc menu. In this case, press TITLE/POP-UP or DISC MENU button and choose the appropriate audio from the selections on the disc menu. yy Immediately after you have switched sound, there may be a temporary discrepancy between the display and actual sound. yy On BD-ROM disc, the multi audio format (5.1CH or 7.1CH) is displayed with [MultiCH] in the on-screen display. 4 Operating 2. Select the [Time] option and then input the required start time in hours, minutes, and seconds from left to right. 3. Use A/D to select desired audio language, audio track or audio channel. 40 Operating Selecting a subtitle language eroy 1. During playback, press INFO/DISPLAY (m) to display the On-Screen display. 2. Use W/S to select the [Subtitle] option. 3. Use A/D to select desired subtitle language. 4. Press BACK (x) to exit the On-Screen display. ,,Note Some discs allow you to change subtitle selections only via the disc menu. If this is the case, press TITLE/POPUP or DISC MENU button and choose the appropriate subtitle from the selections on the disc menu. 4 Watching from a different angle er If the disc contains scenes recorded at different camera angles, you can change to a different camera angle during playback. 1. During playback, press INFO/DISPLAY (m) to display the On-Screen display. 2. Use W/S to select the [Angle] option. 3. Use A/D to select desired angle. 4. Press BACK(x) to exit the On-Screen display. Changing the TV Aspect Ratio eroy You can change the TV aspect ratio setting while playback. Operating 1. During playback, press INFO/DISPLAY (m) to display the On-Screen display. 2. Use W/S to select the [TV Aspect Ratio] option. 3. Use A/D to select desired option. 4. Press BACK(x) to exit the On-Screen display. ,,Note Even if you change the value of the [TV Aspect Ratio] option in On-Screen display, the [TV Aspect Ratio] option in the [Setup] menu is not changed. Operating 41 Changing the Picture Mode eroy Changing subtitle code page y You can change the [Picture mode] option while playback. If the subtitle is displayed in broken letter, you can change the subtitle code page to view the subtitle file properly. 1. During playback, press INFO/DISPLAY (m) to display the On-Screen display. 2. Use W/S to select the [Picture Mode] option. 3. Use A/D to select desired option. 4. Press BACK(x) to exit the On-Screen display. 1. During playback, press INFO/DISPLAY (m) to display the playback menu. 2. Use W/S to select the [Code Page] option. 3. Use A/D to select desired code option. Setting the [User setting] option 1. During playback, press INFO/DISPLAY (m) to display the On-Screen display. 2. Use W/S to select the [Picture Mode] option. 3. Use A/D to select the [User setting] option, and press ENTER (b). ,,Note This function may not be available according to areas. 4. Use W/S/A/D to adjust the [Picture Mode] options. Select [Default] option then press ENTER (b) to reset the all video adjustments. 5. Use W/S/A/D to select the [Close] option, and press ENTER (b) to finish setting. 4 Operating 4. Press BACK(x) to exit the On-Screen display. 42 Operating Audio CD Recording You can record one desired track or all of the tracks in Audio CD to a USB storage device. 1. Insert a USB storage device to the USB port on the front panel. 2. Put a disc with the label facing front to the disc slot as below. The playback starts automatically. 3. Press INFO/DISPLAY (m) to display the option menu Or press XREC button on the remote control. You can record all musics in the audio CD. 4. Use W/S to select [CD Recording] option, and press ENTER (b). 4 Selects all the tracks on an Audio CD. Operating Selects an encoding option from the pop-up menu (128kbps, 192kbps, 320kbps) Cancels the recording and returns to the previous screen. 5. Use W/S/A/D to select [Start], and press ENTER (b). 6. Use W/S/A/D to select a destination folder to be copied. If you want to create a new folder, use W/S/A/D to select [New Folder] and press ENTER (b). Enter a folder name using virtual keyboard, and press ENTER (b) while [OK] is selected. 7. Use W/S/A/D to select [OK], and press ENTER (b) to start Audio CD recording. If you want to stop in progressing Audio CD recording, press ENTER (b) while [Cancel] is highlighted. 8. A message appears when Audio CD recording is completed. Press ENTER (b) to check the music file created in the destination folder. ,,Note yy The table below shows the average recording time from an audio track with 4 minutes of playback time to a music file with 192 kbps as an example. stop mode while playback 1 min. 4 min. yy Recording times in the table above are approximate. yy Actual recording time for USB storage device varies depending on the USB storage device’s ability. yy Make sure that there is minimum of 50 MB free space is needed when recording into the USB storage device. yy The length of the music should be longer than 20 seconds for the proper recording. yy Do not turn off this player or extract the connected USB storage device during Audio CD recording. >>Caution The recording or copying features on this player are provided for your personel and noncommercial use. The making of unauthorized copies of copy-protected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes. LG expressly disclaims any responsibility for illegal distribution or use of unauthorized content in commercial purpose. Be Responsible Respect Copyrights Operating 43 Displaying MP3 music information (ID3 Tag) 1. Select a music file using W/S/A/D. 2. Press INFO/DISPLAY (m) to display the option menu. 3. Select [Information] option using W/S, and press ENTER (b). 4. The music information will be displayed on the screen. Radio Operations Be sure that the antenna is connected. (Refer to the page 18) Listening to the radio 1. Press RADIO&INPUT (P) until TUNER (FM) appears in the display window. The last received station is tuned in. 2. Press and hold TUNING (-/+) for about two seconds until the frequency indication starts to change. Scanning stops when the unit tunes in a station. Or Press TUNING (-/+) repeatedly. 3. Adjust the volume by rotating VOLUME on the front panel or by pressing VOL (+/- ) on the remote control. Presetting the Radio Stations 1. Press RADIO&INPUT (P) until the TUNER (FM) appears in the display window. 2. Select the desired frequency by using TUNING (-/+). 3. Press ENTER (b) a preset number will flash in the display window. 4. Press PRESET (-/+) to select the preset number you want. 5. Press ENTER (b). The station is stored. 6. Repeat the steps 2 to 5 to store other stations. Deleting all the saved stations Press and hold CLEAR for two seconds. “ERASE ALL” will flash up. Then all the saved stations are deleted. 4 Operating ,,Note yy Depending on the MP3 files, information may not be displayed on the screen. You can preset 50 stations for FM. Before tuning, make sure that you have turned down the volume. 44 Operating Deleting a saved station 1. Press PRESET (-/+) to Select a preset number you want to delete. 2. Press CLEAR, the preset number will blink in the display window. 3. Press CLEAR again, to delete the selectd preset number. Improving poor FM reception Press B (blue) (MONO/STEREO) coloured button on the remote control. This will change the tuner from stereo to mono and usually improve the reception. Enjoying the NetCast™ Entertainment Access You can use various content services via Internet with the NetCast Entertainment Access feature. 1. Check the network connection and settings (page 20). 2. Press HOME (n). 3. Select the [NetCast] using A/D, and press ENTER (b). See information about a radio station 4 The FM tuner is supplied with the RDS (Radio Data System) facility. This shows information about the radio station being listened to. Press RDS repeatedly to cycle through the various data types: Operating PS (Programme Service Name) The name of the channel will appear in the display PTY (Programme Type Recognition) The programme type (e.g. Jazz or News) will appear in the display. RT (Radio Text) A text message contains special information from the broadcast station. This text may scroll across the display. CT (Time controlled by the channel) This shows the time and date as broadcast by the station. 4. Select an option using W/S/A/D, and press ENTER (b). ,,Note yy Detailed information of each service, contact to the content provider or visit support link of the service. yy The content of NetCast services and service related information, including user interface, is subject to changes. Please refer to the web site of each service for most up-to-date information. 45 Troubleshooting General Symptom Cause & Solution The Power does not turned on. Plug the power cord into the wall outlet securely. The unit does not start playback. yy Insert a playable disc. (Check the disc type, colour system, and regional code.) yy Place the disc with the playback side down. yy Place the disc on the disc slot correctly. yy Clean the disc. yy Cancel the Rating function or change the rating level. The angle cannot be changed. Multi-angles are not recorded on the DVD Video being played. Cannot play movie, photo or music files. yy The files are not recorded in a format that the unit can play. The remote control does not work properly. yy The remote control is not pointed at the remote sensor of the unit. yy The unit does not support the codec of the movie file. yy The remote control is too far from the unit. yy There is an obstacle in the path of the remote control and the unit. yy The batteries in the remote control are exhausted. The unit is not operating normally. You can reset the unit as follows. Unplug the power cord, wait at least five seconds, and then plug it in again. 5 Troubleshooting The unit is plugged in, but the power will not turn on or off. 46 Troubleshooting Network Symptom Cause & Solution BD-Live feature does not yy The connected USB storage may not have enough space. Connect the USB storage with at least 1GB free space. work. yy Ensure that the unit is correctly connected to the local area network and can access the internet (see page 20). yy Your broadband speed may not fast enough to use the BD-Live features. Contact your Internet Service Provider (ISP) and increase the broadband speed is recommended. yy The [BD-LIVE connection] option in the [Setup] menu is set to [Prohibited]. Set the option to [Permitted]. Streaming video services (such as YouTube™, etc.) are often stopped or “buffer” during playback. Your broadband service speed may not be fast enough to stream video services. Contact your Internet Service Provider (ISP) and increase the broadband speed is recommended. Shared folder or files from your media server are not displayed on the device list. The player is not connected to the local area network that your media server are connected. Picture 5 Troubleshooting Symptom Cause & Solution There is no picture. yy Select the appropriate video input mode on the TV so the picture from the unit appears on the TV screen. yy Connect the video connection securely. yy Check the [HDMI Color Setting] in the [Setup] menu is set to the appropriate item that conforms to your video connection. yy Your TV may not suppot the resolution you have set on the player. Change the resolution that your TV accepts. yy The player’s HDMI OUT jack is connected to a DVI device that does not support copyright protection. Picture noise appears yy You are playing a disc recorded in a color system that is different from your TV. yy Set the resolution which your TV accepts. Blu-ray 3D disc playback does not output 3D views. yy Connect the player to your TV with HDMI cable (Type A, High Speed HDMI™ Cable). yy Your TV may not support “HDMI 1.4 3D mandatory format”. yy The [3D Mode] option in the [Setup] menu is set to [Off ]. Set the option to [On]. Troubleshooting 47 Sound Symptom Cause & Solution There is no sound or the sound is distorted. yy The unit is in scan, slow motion, or pause mode. yy The sound volume is low. yy Check the speaker cable connection. Customer Support You can update the Player using the latest software to enhance the products operation and/or add new features. To obtain the latest software for this player (if updates have been made), please visit http://lgservice.com or contact LG Electronics customer care center. Open source software notice To obtain the corresponding source code under GPL, LGPL and other open source licenses, please visit http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are available to download with the source code. 5 Troubleshooting 48 Appendix Controlling a TV with the Supplied Remote Control You can control your TV using the buttons below. By pressing You can 1 (TV POWER) Turn the TV on or off. AV/INPUT Switch the TV’s input source between the TV and other input sources. PR/CH W/S Scan up or down through memorized channels. VOL +/– Adjust the volume of the TV ,,Note Depending on the unit being connected, you may not be able to control your TV using some of the buttons. 6 Setting up the remote to control your TV You can operate your TV with the supplied remote control. If your TV is listed in the table below, set the appropriate manufacturer code. 1. While holding down 1 (TV POWER) button, and press the manufacturer code for your TV with the numerical buttons (see the table below). Manufacturer Code Number LG 1(Default), 2 Zenith 1, 3, 4 GoldStar 1, 2 Samsung 6, 7 Sony 8, 9 Hitachi 4 2. Release the 1 (TV POWER) button to complete setting. Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again. Appendix Appendix 49 Network Software Update Network update notification From time to time, performance improvements and/or additional features or services may be made available to units that are connected to a broadband home network. If there is new software available and the unit is connected to a broadband home network, the player will inform you about the update as follows. Software Update You can update the player using the latest software to enhance the products operation and/or add new features. You can update the software by connecting the unit directly to the software update server. ,,Note yy Before updating the software in your player, remove any disc and USB Device from the player. yy Before updating the software in your player, turn the player off and then turn it back on. Option 1: yy During the software update procedure, do not turn off the player or disconnect AC power, or do not press any button. 1. The update menu will appear on the screen when you turn on the player. yy If you cancel the update, turn off the power and turn it on for stable performance. 2. Use A/D to select a desired option and then press ENTER (b). yy This unit cannot be updated to previous software version. 1. Check the network connection and settings (page 20). 2. Select [Software] option in the [Setup] menu then press ENTER (b). 3. Select [Update] option, and press ENTER (b). Starts the software update. [Cancel] Exits the update menu and displays it next booting. [Hide] Exits the update menu and it does not appear until next software is uploaded in the update server. Option 2: If the software update is available from the update server, the “Software Update” icon appears at the bottom of the Home menu. Press blue (B) colored button to start the update procedure. 6 Appendix [OK] The player will check for the newest update. ,,Note yy Pressing ENTER (b) while checking for the update will end the process. yy If there is no update available, the Message, “No update is found.” appears. Press ENTER (b) to return to the [Home Menu]. 4. If newer version exists, the message “A new update was found. Do you want to download it?” appears. 50 Appendix 5. Select [OK] to download the update. (Selecting [Cancel] will end the update.) 6. The player starts downloading the newest update from the server. (Downloading will takes several minutes depending on your home network condition) 7. When downloading is completed, the message, “Download is complete. Do you want to update?” appears. 8. Select [OK] to start updating. (Selecting [Cancel] will end the update and downloaded file will not be re-usable. To update software the next time, the software update procedure has to be started from the beginning again.) >>Caution Do not turn off the power during the software update. 9. When update is completed, the power will be turned off automatically in a few seconds. 10.Turn the power back on. The system now operates with the new version. ,,Note 6 The Software Update function may not work properly depending on your internet environment. In this case, you can obtain the latest software from the authorized LG Electronics Service Center then update your player. Refer to “Customer Support” on page 47. About Nero MediaHome 4 Essentials Nero MediaHome 4 Essentials is a software for sharing video, audio and photo files stored on your computer to this player as a DLNA-compatiable digital media server. ,,Note yy The Nero MediaHome 4 Essentials CDROM is designed for PCs and should not be inserted in this player or in any product other than a PC. yy The supplied Nero MediaHome 4 Essentials CD-ROM is a customized software edition only for sharing files and folders to this player. yy The supplied Nero MediaHome 4 Essentials software does not support following functions: Transcoding, Remote UI, TV control, Internet services and Apple iTunes yy This manual explains operations with the English version of Nero MediaHome 4 Essentials as examples. Follow the explanation referring to the actual operations of your language version. Appendix Installing Nero MediaHome 4 Essentials Before you install Nero MediaHome 4 Essentials, check the system requirement shown below. yy Windows® XP (Service Pack 2 or higher), Windows Vista® (no Service Pack required), Windows® XP Media Center Edition 2005 (Service Pack 2 or higher), Windows Server® 2003 yy Windows Vista® 64-bit edition (application runs in 32-bit mode) yy Hard drive space: 200 MB hard drive space for a typical installation of Nero MediaHome standalone yy 1.2 GHz Intel® Pentium® III or AMD Sempron™ 2200+ processors yy Memory: 256 MB RAM Appendix yy Graphics card with at least 32 MB video memory, minimum resolution of 800 x 600 pixels, and 16bit color settings yy Windows® Internet Explorer® 6.0 or higher yy DirectX® 9.0c revision 30 (August 2006) or higher yy Network environment: 100 Mb Ethernet, WLAN Start up your computer, and insert the supplied CDROM disc into your computer’s CD-ROM drive. An installation wizard will walk you through the quick and uncomplicated installation process. To install Nero MediaHome 4 Essentials, proceed as follows: 1. Close all Microsoft Windows programs and exit any anti-virus software that may be running. 2. Insert the supplied CD-ROM disc into your computer’s CD-ROM drive. 3. Click [Nero MediaHome 4 Essentials]. 4. Click [Run] to start installation. 5. Click [Nero MediaHome 4 Essentials]. The installation is prepared and the installation wizard appears. 6. Click the [Next] button to display the serial number input screen. Click [Next] to go to the next step. 7. If you accept all conditions, click [I accept the License Conditions] check box and click [Next]. Installation is not possible without this agreement. 8. Click [Typical] and click [Next]. The installation process is started. 10.Click the [Exit] button to complete the installation. Sharing files and folders On your computer, you must share the folder contained movie, music and/or photo content to play them on this player. This parts explains the procedure for selecting the shared folders on your computer. 1. Double-click the “Nero MediaHome 4 Essentials” icon on the desktop. 2. Click [Network] icon on the left and define your network name in the [Network name] field. The Network name you enter will be recognized by your player. 3. Click [Shares] icon on the left. 4. Click [Local Folders] tab on the [Shares] screen. 5. Click [Add] icon to open the [Browse Folder] window. 6. Select the folder containing the files you want to share. The selected folder is added to the list of shared folders. 7. Click [Start Server] icon to start the server. ,,Note yy If the shared folders or files are not displayed on the player, click the folder on the [Local Folders] tab and click [Rescan Folder] at the [More] button. yy Visit www.nero.com for more information and software tools. 6 Appendix 9. If you want to take part in the anonymous collection of data, select the check box and click the [Next] button. 51 52 Appendix Area Code List Choose an area code from this list. Area Code Area Code Area Code Area Code Afghanistan AF Fiji FJ Monaco MC Singapore SG Argentina AR Finland FI Mongolia MN Slovak Republic SK Australia AU France FR Morocco MA Slovenia SI Austria AT Germany DE Nepal NP South Africa ZA Belgium BE Great Britain GB Netherlands NL South Korea KR Bhutan BT Greece GR Antilles AN Spain ES Bolivia BO Greenland GL New Zealand NZ Sri Lanka LK Brazil BR Hong Kong HK Nigeria NG Sweden SE Cambodia KH Hungary HU Norway NO Switzerland CH Canada CA India IN Oman OM Taiwan TW Chile CL Indonesia ID Pakistan PK Thailand China CN Israel IL Panama PA Turkey TR Colombia CO Italy IT Paraguay PY Uganda UG Congo CG Jamaica JM Philippines PH Ukraine UA Costa Rica CR Japan JP Poland PL United States US Croatia HR Kenya KE Portugal PT Uruguay UY Czech Republic CZ Kuwait KW Romania RO Uzbekistan UZ Denmark DK Libya Ecuador EC Luxembourg LY Russian LU Federation Egypt EG Malaysia 6 El Salvador SV Maldives MY Saudi Arabia MV Senegal Appendix Ethiopia ET Mexico MX Vietnam RU Zimbabwe SA SN TH VN ZW Appendix 53 Language Code List Use this list to input your desired language for the following initial settings: [Disc Audio], [Disc Subtitle] and [Disc Menu]. Code Language Code Language Code Language Code Afar 6565 French 7082 Lithuanian 7684 Sindhi 8368 Afrikaans 6570 Frisian 7089 Macedonian 7775 Singhalese 8373 Albanian 8381 Galician 7176 Malagasy 7771 Slovak 8375 Ameharic 6577 Georgian 7565 Malay 7783 Slovenian 8376 Arabic 6582 German 6869 Malayalam 7776 Spanish 6983 Armenian 7289 Greek 6976 Maori 7773 Sudanese 8385 Assamese 6583 Greenlandic 7576 Marathi 7782 Swahili 8387 Aymara 6588 Guarani 7178 Moldavian 7779 Swedish 8386 Azerbaijani 6590 Gujarati 7185 Mongolian 7778 Tagalog 8476 Bashkir 6665 Hausa 7265 Nauru 7865 Tajik 8471 Basque 6985 Hebrew 7387 Nepali 7869 Tamil 8465 Bengali; Bangla 6678 Hindi 7273 Norwegian 7879 Telugu 8469 Bhutani 6890 Hungarian 7285 Oriya 7982 Thai 8472 Bihari 6672 Icelandic 7383 Panjabi 8065 Tonga 8479 Breton 6682 Indonesian 7378 Pashto, Pushto 8083 Turkish 8482 Bulgarian 6671 Interlingua 7365 Persian 7065 Turkmen 8475 Burmese 7789 Irish 7165 Polish 8076 Twi 8487 Byelorussian 6669 Italian 7384 Portuguese 8084 Ukrainian 8575 Chinese 9072 Japanese 7465 Quechua 8185 Urdu 8582 Croatian 7282 Kannada 7578 Rhaeto-Romance 8277 Uzbek 8590 Czech 6783 Kashmiri 7583 Rumanian 8279 Vietnamese 8673 Danish 6865 Kazakh 7575 Russian 8285 Volapük 8679 Dutch 7876 Kirghiz 7589 Samoan 8377 Welsh 6789 English 6978 Korean 7579 Sanskrit 8365 Wolof 8779 Esperanto 6979 Kurdish 7585 Scots Gaelic 7168 Xhosa 8872 Estonian 6984 Laothian 7679 Serbian 8382 Yiddish 7473 Faroese 7079 Latin 7665 Serbo-Croatian 8372 Yoruba 8979 Fiji 7074 Latvian, Lettish 7686 Shona 8378 Zulu 9085 Finnish 7073 Lingala 7678 6 Appendix Language 54 Appendix Trademarks and Licenses Blu-ray Disc™, Blu-ray™, Blu-ray 3D™, BD-Live™, BONUSVIEW™ and the logos are trademarks of the Blu-ray Disc Association. Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC. 6 Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks,& DTS-HD, DTS-HD Master Audio | Essential and the DTS logos are trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved. “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation. DLNA®, the DLNA Logo and DLNA CERTIFIED® are trademarks, service marks, or certification marks of the Digital Living Network Alliance. “x.v.Color” is a trademark of Sony Corporation. Appendix “AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. DivX®, DivX Certified® and associated logos are trademark of DivX, Inc., and are used under license. Appendix 55 Video Output Resolution VIDEO OUT connection The resolution of the VIDEO OUT jack is always outputted at 480i (or 576i) resolution. HDMI OUT connection yy If you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto]. yy If you select a resolution that your TV does not accept, the warning message will appear. After resolution change, if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution. yy The 1080p video output frame rate may be automatically set to either 24 Hz or 60 Hz depending both on the capability and preference of the connected TV and based on the native video frame rate of the content on the BD-ROM disc. 6 Appendix 56 Appendix Specifications General Power requirements Refer to the main label Power consumption Refer to the main label Dimensions (W x H x D) Approx. 436 x 185 x 142 mm without foot Net Weight (Approx.) 3.0 kg Operating temperature 41 °F to 95 °F (5 °C to 35 °C) Operating humidity 5 % to 90 % Inputs/Outputs VIDEO OUT 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1 HDMI OUT (video/audio) 19 pin (Type A, HDMI™ Connector) ANALOG AUDIO IN 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1 DIGITAL IN (OPTICAL) Optical jack x 2 PORT. IN 0.5 Vrms (3.5 mm stereo jack) Tuner FM Tuning Range 87.5 to 108.0 MHz or 87.50 to 108.00 MHz Amplifier 6 Total 400 W Front 130W x 2 Sub-Woofer 140 W (Passive) Appendix Appendix 57 System Laser Semiconductor laser Wavelength 405 nm / 650 nm Signal system Standard NTSC/PAL colour TV system Frequency response 20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling) Signal-to-noise ratio More than 85 dB Total harmonic distortion 0.05 % at 1 W Dynamic range More than 90 dB LAN port Ethernet jack x 1, 10BASE-T/100BASE-TX Bus Power Supply (USB) DC 5 V 0 500 mA Speakers Front speaker (Left/ Right) Type 2 Way 2 speaker Max. Input power 260 W Impedance Rated 3Ω Net Dimensions (W x H x D) 110 x 222 x 107 mm Input Power 130 W Net Weight 1.15 kg 1 Way 1 speaker Max. Input power 280 W Impedance Rated 3Ω Net Dimensions (W x H x D) 190 x 385 x 318 mm Input Power 140 W Net Weight 5.0 kg Subwoofer Type yy Design and specifications are subject to change without notice. 6 Appendix 58 Appendix Maintenance Notes on Discs Handling Discs Handling the Unit When shipping the unit Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Keeping the exterior surfaces clean yy Do not use volatile liquids such as insecticide spray near the unit. yy Wiping with strong pressure may damage the surface. yy Do not leave rubber or plastic products in contact with the unit for a long period of time. Cleaning the unit To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Maintaining the Unit 6 Appendix The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized Service Center. Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc. Storing Discs After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. Cleaning Discs Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center to out. Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records. Appendix 59 Important Information Relating to Network Services All information, data, documents, communications, downloads, files, text, images, photographs, graphics, videos, webcasts, publications, tools, resources, software, code, programs, applets, widgets, applications, products and other content (“Content”) and all services and offerings (“Services”) provided or made available by or through any third party (each a “Service Provider”) is the sole responsibility of the Service Provider from whom it originated. The availability of and access to Content and Services furnished by the Service Provider through the LGE Device are subject to change at any time, without prior notice, including, but not limited to the suspension, removal or cessation of all or any part of the Content or Services. Should you have any inquiry or problem related to the Content or Services, you may refer to the Service Provider’s website for the most up-todate information. LGE is neither responsible nor liable for customer service related to the Content and Services. Any question or request for service relating to the Content or Services should be made directly to the respective Content and Service Providers. 6 Appendix Please note that LGE is not responsible for any Content or Services provided by the Service Provider or any changes to, removal of, or cessation of such Content or Services and does not warrant or guaranty the availability of or access to such Content or Services.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project