LG | SR906SB | LG SR906SB Owner’s Manual

OWNER’S MANUAL
5.1ch SURROUND COMPACT RECEIVER SYSTEM
Please read this manual carefully before operating
your set and retain it for future reference.
FOR THE GUARANTEE TERMS & CONDITIONS,
PLEASE REFER TO INNER PAGE OF BACK COVER.
SR906SB (SR906SB, SH96SB-F/S/C, SH95TA-W)
P/NO : MFL63267062
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Getting Started
POWER: This unit operates on a mains supply of
200-240V~, 50/60Hz.
Warning: A mains plug removed from the mains
lead of this unit must be destroyed. A mains plug
with bared wires is hazardous if inserted in a mains
socket. Do not connect either wire to the earth pin,
marked with the letter E or with the earth symbol
or coloured green or green and yellow. If any
other plug is fitted, use a 5 amp fuse, either in the
plug, or at the distribution board.
Important: The wires in this mains lead are
coloured in accordance with the following codes: - BLUE: NEUTRAL, BROWN: LIVE - As the colours
of the wires in the mains lead of this unit may not
correspond with the coloured marking identifying
the terminals in your plug, proceed as follows: The
wire which is coloured blue must be connected
to the terminal which is marked with the letter
N or coloured black. The wire which is coloured
brown must be connected to the terminal which is
marked with the letter L or coloured red.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product, it
means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and
other relevant provisions of Directive 2004/108/EC,
2006/95/EC and 2009/125/EC.
European representative : LG Electronics Service
Europe B.V. Veluwezoom 15, 1327 AE Almere, The
Netherlands (Tel : +31-(0)36-547-8888)
1
Getting Started
Wiring: This unit is supplied with a BSI 1363
approved 13 amp mains plug, fused at 5 amp.
When replacing the fuse always use a 5 amp BS
1362, BSI or ASTA approved type. Never use this
plug with the fuse cover omitted. To obtain a
replacement fuse cover contact your dealer. If the
type of plug supplied is not suitable for the mains
sockets in your home, then the plug should be
removed and a suitable type fitted. Please refer to
the wiring instructions below:
3
4
Table of Contents
Table of Contents
3 System Setting
19
1
Getting Started
2
6
6
6
7
7
7
7
9
Safety Information
Introduction
– Supplied Accessories
– Required cables
Remote control
– Battery Installation
– About the remote control modes
– To control the RECEIVER
– To control the PLAYER (Blu-ray disc
player, DVD player, DVD recorder, etc.)
– To control the TV
Front panel
Rear panel
9
10
11
2 Connecting
12
13
13
14
14
16
16
16
16
17
17
17
18
18
18
18
Positioning the system
Speaker Connection
– Attaching the speakers to the receiver
Connecting to Your TV
Connecting components with HDMI jack
– What is SIMPLINK?
– ARC (Audio Return Channel) function
Connecting components with digital
audio jacks
– Optical digital audio connection
– Coaxial digital audio connection
Connecting component with analog audio
jacks
Connecting the portable device
Connecting the antennas
Connecting the optimizer microphone
Connecting the USB device
Connecting the iPod
19
19
20
21
21
21
22
22
22
23
23
23
23
Calibrating the appropriate settings
automatically (Auto Sound Calibration)
– Before performing Auto Sound
Calibration
– Performing Auto Sound Calibration
– Turning the Auto Sound Calibration
on/off
Settings and adjustments using the
SETUP menu
– SETUP configuration
– TESTTONE menu
– LEVEL menu
– DISTANCE menu
– A/V SYNC menu (Adjusting the audio
delay)
– DRC menu
– SET HDMI menu (HDMI Standby Pass
Trough)
– AUTO CAL menu
– RESET menu
Table of Contents
4 Operating
24 Selecting the input source
24 Enjoying sound/images from the
components connected to the receiver
24 – Enjoying Blu-ray Disc/DVD
25 – Enjoying a satellite tuner or set top
box
25 – Enjoying TV
25 – Enjoying a game console, etc
26 – Enjoying a CD player, etc
26 – Enjoying a VCR, etc
26 – Enjoying a portable device (MP3
player, etc.)
26 – Enjoying the USB or iPod connected
to the IPod/USB Port
27 Adjusting the speaker levels
27 Enjoying various sound mode
28 Listening to FM radio
28 – Automatic tuning
28 – Manual tuning
28 – Improving poor FM reception
28 – Presetting radio stations
28 – Tuning to preset stations
29 – Deleting the preset stations
29 – Deleting all the preset stations
29 – Seeing information about a radio
station
30 Playing back components with one-touch
operation (One-Touch Play)
30 Enjoying the TV sound from the speakers
connected to the receiver (System Audio
Control)
31 Turning off the receiver with the TV
(System Power Off)
31 Enjoying the TV sound via an HDMI
connection (Audio Return Channel)
31 Adjusting the audio delay
31 DOLBY DRC (Dynamic Range Control)
32 Using the Sleep Timer
32 Displaying the file information
33 Playing music files using the USB device
33 – Basic Operation
33 – Playing repeatedly or randomly
33 – Music file requirement
33 – USB device requirement
34 Playing the iPod
5
35 Controlling a TV with the Supplied
Remote Control
35 – Setting up the remote to control your
TV
1
5 Troubleshooting
36 Troubleshooting
6 Appendix
38
44
45
46
46
Manufacturer code list
Trademarks and Licenses
Specifications
Maintenance
– Handling the Unit
7 Warranty
2
3
4
5
6
7
6
1
Getting Started
Getting Started
Introduction
Required cables
Supplied Accessories
You must purchase the connection cables
separately if necessary.
The hookup diagrams on the subsequent pages
assume the use of the following connection cables.
yy HDMI cable (Type A, High speed HDMI™ cable or
Type A, High speed HDMI™ cable with Ethernet)
Optimizer microphone
(1)
Speaker cables (6)
yy Optical digital audio cable
yy Coaxial digital audio cable
Remote control (1)
Batteries (2)
yy Portable cable
yy Analog audio cable
FM antenna (1)
White (L)
Red (R)
yy iPod cable
,,Note
The iPod cable is included when you purchase
iPhone or iPod.
Getting Started
Remote control
7
About the remote control
modes
1. Press RECEIVER, PLAYER, or TV buttons to select
the component you want to operate.
- RECEIVER:In RECEIVER Mode, you can control the receiver.
- PLAYER:In PLAYER Mode, you can control a Blu-ray disc player, DVD player, DVD recorder, etc. (For LG product only)
- TV: In TV Mode, you can control TV.
2. Referring to the following contents (pages
7-9), press the corresponding button for the
operation.
To control the RECEIVER
• • • • • • a • • • • • • • • • •
1 (POWER): Turns the receiver on or off.
ARC: Outputs audio signal of the TV via an HDMI
cable (Type A, High speed HDMI™ cable or Type A,
High speed HDMI™ cable with Ethernet).
RECEIVER: Controls the receiver.
Press the corresponding button for the operation
after pressing the RECEIVER button.
INPUT buttons: Selects the input source you want
to use.
- BD: Selects the input source connected to BD IN
jack.
Battery Installation
- DVD: Selects the input source connected to DVD
IN jack.
- STB: Selects the input source connected to STB IN
jack.
- T V: Selects the input source connected to TV IN
jack.
Remove the battery cover on the rear of the
Remote Control, and insert two R03 (size AAA)
batteries with 4 and 5 matched correctly.
- GAME: Selects the input source connected to
GAME IN jack.
- CD: Selects the input source connected to CD IN
jack.
- RADIO: Selects the FM/AM.
- VCR: Selects the input source connected to VCR
IN jack.
1
Getting Started
The remote control has a specific operating mode
for use with each type of component. Modes are
selected by using the three RECEIVER, PLAYER, and
TV buttons on the remote control.
8
1
Getting Started
Getting Started
- PORTABLE: Selects the input source connected to
PORT. IN jack.
• • • • • • e • • • • • • • • • •
- IPOD/USB: Selects the input source connected to
IPOD/USB Port.
RDS: Radio Data System.
PTY: Views the programme type of the RDS.
PTY SEARCH: Searches programme type.
,,Note
In RECEIVER mode, the 0-9 numerical buttons
does not work.
CLEAR: Deletes all the preset stations in tuner
mode.
MONO/STEREO: Selects mono/ stereo in FM mode.
SLEEP: Sets the system to turn off automatically at
a specified time.
AUTO CAL.: Performs the Auto Sound Calibration.
SETUP: Moves to the [SETUP] menu.
REPEAT (h): Plays the files repeatedly or
randomly in iPod or USB mode.
DOLBY DRC: Sets the Dolby DRC (Dynamic Range
Control).
• • • • • • b • • • • • • • • • •
AV SYNC.: Delays the sound output using this
function when the image is slower than the sound.
c/v (SCAN): Searches backward or forward.
C/V (SKIP): Goes to the next or previous
chapter / track / file.
Z (STOP): Stops playback.
d (PLAY): Starts playback.
M (PAUSE): Pauses playback.
• • • • • • c • • • • • • • • • •
VOL +/-: Adjusts speaker volume.
SOUND: Selects a sound effect mode.
MUTE ( ): Turns off the sound temporarily. Press
the button again to restore the sound.
• • • • • • d • • • • • • • • • •
INFO/DISPLAY (m): Displays information of music
files or digital input source.
ENTER (b): Acknowledges menu selection.
PRESET +/-: Selects a preset stations in tuner
mode.
TUNING +/-: Tunes in the desired radio station in
tuner mode.
BACK (x): Returns to the upper menu of any
displayed menu.
DISC MENU: Returns to the upper menu in iPod
mode.
SPEAKER LEVEL: Sets the sound level of desired
speaker.
Getting Started
To control the PLAYER (Bluray disc player, DVD player,
DVD recorder, etc.)
• • • • • • a • • • • • • • • • •
B (OPEN/CLOSE): Opens and closes the disc tray.
To control the TV
• • • • • • a • • • • • • • • • •
1 (POWER): Turns the TV on or off.
0-9 numerical buttons: Selects numbered options
in a menu or inputs letters in the keypad menu.
• • • • • • c • • • • • • • • • •
PLAYER: Controls the PLAYER (Blu-ray disc player,
DVD player, DVD recorder, etc.).
Press the corresponding button for the operation
after pressing the PLAYER button.
VOL +/-: Adjusts the volume.
0-9 numerical buttons: Selects numbered options
in a menu or inputs letters in the keypad menu.
PR/CH W/S: Selects the channel.
CLEAR: Removes a mark on the search menu or a
number when setting the password.
REPEAT (h): Repeats a desired section or
sequence.
• • • • • • b • • • • • • • • • •
c/v (SCAN): Searches backward or forward.
C/V (SKIP): Goes to the next or previous
chapter / track / file.
Z (STOP): Stops playback.
d (PLAY): Starts playback.
M (PAUSE): Pauses playback.
• • • • • • d • • • • • • • • • •
HOME (n): Displays or exits the [Home Menu].
INFO/DISPLAY (m): Displays or exits On-Screen
Display.
Direction buttons (A/D/W/S): Selects an
option in the menu.
ENTER (b): Acknowledges menu selection.
BACK (x): Returns to the upper menu of any
displayed menu.
TITLE/POP UP: Displays the DVD title menu or BDROM’s pop-up menu, if available.
DISC MENU: Accesses menu on a disc.
• • • • • • e • • • • • •
Colored (R, G, Y, B) buttons:
Displays an operation guide on the TV screen
when the color buttons are available. Follow the
operation guide to perform a selected operation.
TV INPUT: Selects the TV’s source.
MUTE ( ): Turns off the sound temporarily. Press
the button again to restore the sound.
,,Note
The above explanation is intended to serve
as an example only. Therefore, depending on
the component, the above operation may not
be possible or may operate differently than
described. In that case, use the remote control
supplied with the component.
1
Getting Started
1 (POWER): Turns the player on or off.
9
10
Getting Started
Front panel
1
Getting Started
a Volume Control
f 1 (POWER)
Adjusts speaker volume.
Turns the receiver on or off.
b Display Window
g IPod/USB Port
Shows the current status of the receiver.
Connects an IPod/USB device to IPod/USB Port.
c FUNCTION
h STAND BY/HDMI THRU indicator
Selects the input source you want to use.
Lights up as follows:
d dM (PLAY / PAUSE)
- Red : The receiver is in standby mode.
- Blue : The receiver is in standby mode, and control for HDMI is set to on.
Starts or pauses playback in iPod or USB mode.
eZ (STOP)
- Lights off when the receiver is turned on.
Mode
To
Do this
USB
Pause
Press Z (STOP).
Playback
Press dM (PLAY / PAUSE).
Stop
Press Z (STOP) twice.
Pause
Press Z (STOP).
Playback
Press dM (PLAY / PAUSE).
IPOD
Getting Started
11
Rear panel
1
Getting Started
a AC power cord
g Cooling fan
b OPTICAL GAME IN
h Speakers connectors
Connects to other components with an optical
digital audio output.
c COAXIAL CD IN
Connects to other components with a coaxial
digital audio output.
d Antenna connectors
Connects to the speakers and subwoofer.
i AUTO CAL MIC
Connects to the optimizer microphone for the
Auto Sound Calibration function.
j OPTICAL TV IN
Connects to the FM wire antenna.
Connects to the TV with an optical digital
audio output.
e PORT. IN
k HDMI OUT
Connects to a portable device (MP3 player, etc)
to PORT. IN jack.
f AUDIO VCR IN
Connects to the components with analog
audio out jacks.
Connects to a TV. When the TV is compatible
with ARC (Audio Return Channel) function,
you can output the TV sound via the speakers
connected to the receiver without connecting
the analog audio cable or the optical digital
audio cable.
l HDMI IN
Connects to a DVD player, satellite tuner, set
top box, Blu-ray Disc player, etc.. The image is
output to a TV or a projector while the sound
can be output from a TV or/and speakers
connected to this receiver.
Connecting
12
Positioning the system
2
The following illustration shows an example of
positioning the system. Note that the illustrations
in these instructions differ from the actual unit for
explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position (A).
Connecting
C
G
F
A
A
A
A
D
E
A
A ABCD E F G
A Front left speaker (L)/ B Front right
speaker (R):
Place the front speakers to the sides of the monitor
or screen and as flush with the screen surface as
possible.
C Center speaker:
Place the center speaker above or below the
monitor or screen.
D Surround left speaker (L)/ E Surround right
speaker (R):
Place these speakers behind your listening position,
facing slightly inwards.
F Subwoofer:
The position of the subwoofer is not so critical,
because low bass sounds are not highly directional.
But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of
the room to reduce the wall reflections.
G Receiver
yy Place the center speaker at a safe distance
from the child’s reach.
Otherwise it may result in the speaker falling
down and causing personal injury and/or
property damage.
yy The speakers contain magnetic parts, so
colour irregularity may occur on the CRT
TV screen or PC monitor screen. Please use
the speakers away from the TV screen or PC
monitor screen.
B
A
>>Caution
yy Be careful to make sure children not to put
their hands or any objects into the *speaker
duct.
*Speaker duct: A hole for plentiful bass
sound on speaker cabinet (enclosure).
Connecting
13
Speaker Connection
Attaching the speakers to the
receiver
1. Connect speaker wires to the receiver.
Each speaker wire is color-coded. Use matching
color wires for corresponding speakers.
2
Connecting
Color
Speaker
Position
Grey
Rear
Rear right
Blue
Rear
Rear left
Green
Center
Center
Orange
Sub
woofer
Any front position
Red
Front
Front right
White
Front
Front left
2. Connect the speaker wire to the terminal on the
speaker.
Make sure the wire marked black goes in to the
terminal marked “–” (minus) and the other wire
goes in to the terminal marked “+” (plus).
14
Connecting
Connecting to Your TV
You can watch the selected input image when you
connect the HDMI OUT jack to a TV.
Before connecting the cables, be sure to disconnect
the AC power cord.
2
FM
AUTO
PORT.IN CAL MIC
HDMI
BD IN
DVD IN
STB IN
ARC
Connecting
Rear of the receiver
L
FM
AUTO
PORT.IN CAL MIC
R
ARC
B Optical digital
audio cable
C HDMI
cable
A Analog audio cable
TV
HDMI IN
ARC
AUDIO OUT
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
,,Note
yy Turn off the power to all components
before making any connections.
yy When connecting optical digital audio
cables, insert the cable plugs straight in
until they click into place.
yy Do not bend or tie optical digital audio
cables.
yy When you use ARC (Audio Return Channel)
function. the audio signal is output from the
TV to the unit. When the TV is compatible
with ARC (Audio Return Channel) function,
the TV sound will output from the speakers
connected to the unit. Be sure to activate
the ARC (Audio Return Channel) function by
pressing ARC.
It is not necessary to connect all the cables.
Connect the cables according to the jacks of your
components.
Connect
To
A Analog
audio cable
or B Optical
digital audio
cable
output the TV sound via the
speakers connected to the
receiver. Be sure to turn off the TV's
volume or activate the TV's
muting function.
C HDMI
cable (Type
A, High speed
HDMI™ cable
or Type A,
High speed
HDMI™ cable
with Ethernet)
output the image to a TV while
the sound can be output from a
TV or/and speakers connected
to the receiver.
When the TV is compatible with
ARC (Audio Return Channel)
function, you can output the
TV sound via the speakers
connected to the receiver
without connecting A Analog
audio cable or B Optical digital
audio cable. For details, see
"Enjoying the TV sound via an
HDMI connection (Audio Return
Channel)" (page 31).
Be sure to turn off the TV's
volume or activate the TV's
muting function.
Connecting
components with
HDMI jack
You can enjoy the image and sound from your
component through this connection.
It is not necessary to connect all the cables.
Connect the cables according to the jacks of your
components.
Connect the HDMI OUT ARC jack on the receiver
to the HDMI IN jack on a HDMI compatible TV or
monitor. Connect the HDMI BD IN, HDMI DVD
IN, HDMI STB IN jack on the receiver to your
components with HDMI OUT jack using a HDMI
cable (Type A, High speed HDMI™ cable or Type A,
High speed HDMI™ cable with Ethernet).
Connecting
15
,,Note
FM
AUTO
PORT.IN CAL MIC
HDMI
BD IN
DVD IN
STB IN
ARC
ANTENNA
Rear of the receiver
yy Changing the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn off the receiver and then turn
it on again.
HDMI
BD IN
DVD IN
ARC
STB IN
HDMI IN
ARC
HDMI OUT
HDMI OUT
Satellite tuner, set
top box, etc
DVD player, DVD recorder,
etc.
Blu-ray disc player, etc.
Additional Information for HDMI
yy When you connect a HDMI or DVI compatible
device make sure of the following:
-- Try switching off the HDMI/DVI device and
this receiver. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this receiver.
-- The connected device’s video input is set
correctly for this receiver.
-- The connected device is compatible with
720x480p (NTSC), 720x576p (PAL), 1280x720p,
1920x1080i or 1920x1080p video input.
yy Not all HDCP-compatible HDMI or DVI devices
will work with this receiver.
-- The picture will not be displayed properly
with non-HDCP device.
yy When the HDMI connection with HDCP
is not verified, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
yy If there are noises or lines on the screen,
please check the HDMI cable (length is
generally limited to 4.5 m(15 ft.)).
yy Depending on connection or playing status
TV or external device connected to the
receiver, the receiver may be switched to
OPTICAL input source or ARC function.
yy The Control for HDMI function will not
operate correctly in the following cases:
-- When you connect the receiver to a
components which does not correspond
with Simplink;
-- When you connect the receiver and
components using other than HDMI
connection. We recommend that you connect the
receiver to products featuring “Simplink”. Depending on the connected
component, the Simplink function
may not work. Refer to the operating
instructions of the component.
2
Connecting
TV
HDMI OUT
yy If a connected HDMI device does not accept
the audio output of the receiver, the HDMI
device’s audio sound may be distorted or
may not output.
16
Connecting
What is SIMPLINK?
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.
2
Connecting
components with
digital audio jacks
Connecting
Controllable functions by LG TV’s remote control;
Power Off, Volume control, etc.
You can enjoy the sound from your component
with a digital optical or coaxial connection through
the speakers of this system.
Refer to the TV owner’s manual for the details of
SIMPLINK function.
Before connecting the cables, be sure to disconnect
the AC power cord.
LG TV’s with SIMPLINK function has the logo as
shown above.
,,Note
Depending on the disc type or playing status,
some SIMPLINK operation may differ from your
purpose or not work.
ARC (Audio Return Channel)
function
Optical digital audio
connection
Connect the OPTICAL GAME IN jack on the receiver
to your components with OPTICAL OUT jack using
an optical digital audio cable.
FM
AUTO
PORT.IN CAL MIC
HDMI
BD IN
DVD IN
STB IN
ARC
ANTENNA
Rear of the receiver
The ARC function enables an HDMI capable TV to
send the audio stream to HDMI OUT of this receiver.
To use this function:
-- Your TV must support the HDMI-CEC and ARC
function and the HDMI-CEC and ARC must be
set to On.
-- The setting method of HDMI-CEC and ARC may
differ depending on the TV. For details about
ARC function, refer to your TV manual.
ARC
-- You must use the HDMI cable (Type A, High
Speed HDMI™ cable with Ethernet).
To the digital optical output
jack of your component
(Game console, etc.)
-- You must connect with the HDMI IN that
supports the ARC function using the HDMI OUT
on this receiver.
-- You can connect only one Home Theater to TV
compatible with ARC.
OPTICAL OUT
Connecting
Coaxial digital audio
connection
Connect the COAXIAL CD IN jack on the receiver to
your components with COAXIAL OUT jack using a
coaxial digital audio cable.
FM
AUTO
PORT.IN CAL MIC
HDMI
BD IN
DVD IN
STB IN
ARC
ANTENNA
Rear of the receiver
17
Connecting component
with analog audio jacks
You can enjoy the sound from component with
analog audio jacks through the speakers of this
system.
Connect the AUDIO VCR IN jack on the receiver to
your components with analog audio output jacks
using a analog audio cable.
AUTO
PORT.IN CAL MIC
BD IN
DVD IN
STB IN
ARC
ANTENNA
Rear of the receiver
ARC
AUTO
PORT.IN CAL MIC
White
Red
COAXIAL OUT
To the digital coaxial output
jack of your component
(CD player, etc.)
To the audio output jacks
of your component
(TV, VCR, etc.)
Connecting the
portable device
You can enjoy the sound from your portable audio
player through the speakers of this system.
Connect the PORT. IN jack on the receiver to the
headphones (or line out) jack on your portable
device (MP3 player, etc...) using a portable cable (
3.5 mm).
FM
AUTO
PORT.IN CAL MIC
HDMI
BD IN
DVD IN
STB IN
ARC
ANTENNA
Rear of the receiver
AUTO
PORT.IN CAL MIC
MP3 player, etc.
Connecting
FM
HDMI
2
18
Connecting
Connecting the
antennas
Connecting the USB
device
Connect the supplied antenna for listening to the
radio.
You can enjoy the sound of music files contained in
the USB device.
1. Open the IPod/USB cover.
2. Insert a USB device to the IPod/USB Port until it
fits into place.
2
Connecting
FM
ANTENNA
Front of the receiver
FM
AUTO
PORT.IN CAL MIC
HDMI
BD IN
DVD IN
ARC
STB IN
ANTENNA
Rear of the receiver
,,Note
After connecting the FM wire antenna, keep
it as horizontal as possible. Be sure to fully
extend the FM wire antenna.
Connecting the
optimizer microphone
You can perform the Auto Sound Calibration
function by connecting the optimizer microphone
( 3.5 mm).
Connect the optimizer microphone ( 3.5 mm) into
the AUTO CAL MIC jack on this unit.
Connecting the iPod
You can enjoy the sound with your iPod. For details
about iPod, refer to the iPod’s User Guide.
1. Open the IPod/USB cover.
2. Insert your iPod to the IPod/USB Port until it fits
into place.
Your iPod is automatically turned on and
recharging starts.
FM
AUTO
PORT.IN CAL MIC
HDMI
STB IN
ARC
ANTENNA
Rear of the receiver
Front of the receiver
AUTO
PORT.IN CAL MIC
Optimizer microphone
NU
DVD IN
ME
BD IN
System Setting
Calibrating the
appropriate settings
automatically (Auto
Sound Calibration)
This function allows you to perform automatic
calibration as follows:
yy Adjusts the speaker level.
yy Measures the distance of each speaker from your
listening position.
yy Creates an appropriate EQ (Equalizer) depending
on your room structure.
Performing Auto Sound
Calibration
1. Connect the optimizer microphone ( 3.5 mm)
into the AUTO CAL MIC jack on this unit. (page
18).
2. Set up the optimizer microphone.
Place the optimizer microphone at your
listening position.You can also use a stool
or tripod so that the optimizer microphone
remains at the same height as your ears.
FM
AUTO
PORT.IN CAL MIC
3
ANTENNA
AUTO
CAL MIC
Optimizer
microphone
Before performing Auto Sound
Calibration
yy Before you perform the Auto Sound Calibration,
set up and connect the speakers (pages 12-13).
yy The AUTO CAL MIC jack is used for the supplied
optimizer microphone only. Do not connect
other microphones to this jack. Doing so may
damage the receiver and the microphone.
yy Release the wire of optimizer microphone in
order to get a more accurate measurement.
yy During the calibration, the sound that comes
out of the speakers is very loud. The volume of
the sound cannot be adjusted. Pay attention to
the presence of children or to the effect on your
neighborhood.
yy Perform the Auto Sound Calibration in a quiet
environment to avoid the effect of noise and to
get a more accurate measurement.
yy If there are any obstacles in the path between
the optimizer microphone and the speakers,
the calibration cannot be performed correctly.
Remove any obstacles from the measurement
area to avoid measurement error.
,,Note
If an error message appears on the display
while you are performing the Auto Sound
Calibration, check the above contents.
,,Note
When you face the speaker towards the
optimizer microphone, you will get a more
accurate measurement.
System Setting
The function is designed to obtain proper sound
balance in your room. However, you can adjust
the speaker levels manually according to your
preference. For details, see “Adjusting the speaker
levels” (page 27).
19
20 System Setting
3. Press AUTO CAL..
“TEST START” appears on the display window
and “START” blinks on the display window.
4. Press ENTER (b).
“TEST1 1/4” appears on the display window.
The Auto Sound Calibration is is automatically
measured in the first position from each speaker.
(TEST: 1/4 →TEST: 2/4→TEST: 3/4 →TEST: 4/4)
The measurement process will take
approximately 4 to 5 minutes to complete.
,,Note
yy If each speaker is not connected, the
measurement is stopped.
3
System Setting
yy If “INSERT MIC” appears on the display
window, you cannot perform the Auto
Sound Calibration. Connect the optimizer
microphone, then perform the Auto Sound
Calibration.
5. When the measurement ends, “RESULT SHOW”
appears on the display window for about 5
seconds.
After about 5 seconds, “RESULT USE” appears on
the display window.
6. If you want to confirm the measurement
result, press ENTER (b) while “RESULT SHOW” is
showed on the display window.
If you press ENTER (b) when “RESULT USE” is
showed on the display window, proceed to step
11.
7. Choose the LEVEL and DISTANCE by pressing
W/S.
If you press ENTER (b) when “RESULT USE” is
showed on the display window, proceed to step
11.
8. After pressing ENTER (b), confirm the measured
value by pressing W/S.
9. Press ENTER (b) repeatedly until “RESULT USE”
appears on the display window.
10.press ENTER (b) again.
“1 - YES” and “2 - NO” appear on the display
window.
11.Press numerc 1 to save the measurement result
when “1 - YES” and “2 - NO” are showed on the
display window.
After “ASC DONE” appears on the display window,
the level and the distance is changed automatically.
Then the EQ (Equalizer) is set automatically.
,,Note
yy When you have finished the Auto Sound
Calibration, disconnect the optimizer
microphone from the unit.
yy If you have changed the position of the
speakers, it is recommended that you
perform Auto Sound Calibration again in
order to enjoy the surround sound.
yy The Auto Sound Calibration has been
completed. However, the noise level is
high while you perform the Auto Sound
Calibration. When you play a sound source,
the sound source may not be played
properly. In this case, try to perform the Auto
Sound Calibration in a quiet environment
or reset the receiver to its original factory
settings (refer to the page 23).
yy If the muting function has been activated or
the volume level has been set to "0" before
you perform Auto Sound Calibration, you
can not perform it. After the "CHECK VOL"
appears on the display window for about 5
seconds, it returns to the previous step.
Turning the Auto Sound
Calibration on/off
When you have completed the Auto Sound
Calibration, you can turn it on/off.
Press AUTO CAL. repearedly.
“ASC ON” or “ASC OFF” appears on the display
window.
- ASC ON : Activates the EQ (Equalizer).
- ASC OFF : Deactivates the EQ (Equalizer).
,,Note
If you perform the Auto Sound Calibration for
the first time or reset the receiver to its original
factory settings, the “TEST START” appears on
the display window.
System Setting
Settings and
adjustments using the
SETUP menu
TESTTONE menu
By using the SETUP menus, you can make various
adjustments to customize the unit.
2. Press ENTER (b).
SETUP configuration
SETUP
2 LEVEL
3 DISTANCE
You can adjust the speaker levels while listening to
the test tone from your listening position.
1. Press RECEIVER, and then press SETUP.
"1 TESTTONE" appears on the display window.
The test tone is emitted from each speaker in
sequence as follows:
TESTING : FL → TESTING : C → TESTING : FR →
TESTING : SR → TESTING : SL → TESTING : SW
Display
Description
TESTING : FL
TESTING : C
TESTING : FR
TESTING : SR
TESTING : SL
TESTING : SW
TESTING : FL
Front left speaker (- 6 ~ 0)
3
TESTING : C
Center speaker (- 6 ~ + 6)
TESTING : FR
Front right speaker (- 6 ~ 0)
TESTING : SR
Surround right speaker (- 6 ~
+ 6)
FL : - 6 ~ 0
C:-6~+6
FR : - 6 ~ 0
SR : - 6 ~ + 6
SL : - 6 ~ + 6
SW : - 6 ~ + 6
TESTING : SL
Surround left speaker (- 6 ~ +
6)
System Setting
1 TESTTONE
21
TESTING : SW
Subwoofer (- 40 ~ + 6)
FL : 0.0 M ~ 6.0 M
C : 0.0 M ~ 6.0 M
FR : 0.0 M ~ 6.0 M
SR : 0.0 M ~ 6.0 M
SL : 0.0 M ~ 6.0 M
SW : 0.0 M ~ 6.0 M
4 A/V SYNC
0 MS ~ 300 MS
5 DRC
DRC OFF
DRC ON
6 SET HDMI
STDBY OFF
STDBY ON
7 AUTO CAL
TEST START
8 RESET
1 - YES 2 - NO
3. If you want to adjust the speaker level, press
ENTER (b) when the desired speaker is showed
on the display window.
4. Press A/D repeatedly until the desired
speaker appears.
5. Press W/S to adjust the speaker level and
then press ENTER (b).
6. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
22 System Setting
LEVEL menu
DISTANCE menu
You can adjust the level of each speaker to suit your
preference.
You can set the distance of the speakers connected
to this unit.
1. Press RECEIVER, and then press SETUP.
1. Press RECEIVER, and then press SETUP.
"1 TESTTONE" appears on the display window.
3
"1 TESTTONE" appears on the display window.
2. Press W/Srepeatedly until “2 LEVEL” appears,
then press ENTER (b).
2. Press W/S repeatedly until “3 DISTANCE"
appears, then press ENTER (b).
3. Press A/D repeatedly until the desired
speaker appears.
3. Press A/D repeatedly until the desired speaker
appears.
System Setting
Display
Description
Display
Description
FL
Front left speaker (- 6 ~ 0)
FL
Front left speaker (0.0 M ~ 6.0 M)
C
Center speaker (- 6 ~ + 6)
C
Center speaker (0.0 M ~ 6.0 M)
FR
Front right speaker (- 6 ~ 0)
FR
Front right speaker (0.0 M ~ 6.0 M)
SR
Surround right speaker (- 6 ~ + 6)
SR
Surround right speaker (0.0 M ~ 6.0 M)
SL
Surround left speaker (- 6 ~ + 6)
SL
SW
Subwoofer (- 40 ~ + 6)
Surround left speaker (0.0 M ~ 6.0 M)
SW
Subwoofer (0.0 M ~ 6.0 M)
4. Press W/S to adjust the level of each speaker
and then press ENTER (b).
5. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
4. Press W/S to set the distance of the speakers
and then press ENTER (b).
5. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
A/V SYNC menu (Adjusting
the audio delay)
You can delay the sound output using this function
when the image is slower than the sound.
1. Press RECEIVER, and then press SETUP.
"1 TESTTONE" appears on the display window.
2. Press W/Srepeatedly until “4 A/V SYNC”
appears, then press ENTER (b).
3. Press W/S to adjust the delay between sound
and image and then press ENTER (b).
You can adjust from 0 MS to 300 MS in 10 MS
steps.
4. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
,,Note
You may not be able to adjust the delay
between sound and image perfectly using this
function.
System Setting 23
DRC menu
AUTO CAL menu
This function allows you to listen to a movie at a
lower volume without losing clarity of sound. You
can compress the dynamic range of the Dolby
Digital audio output.
This allows you to perform automatic calibration.
For details, see the pages 19 - 20.
1. Press RECEIVER, and then press SETUP.
"1 TESTTONE" appears on the display window.
2. Press W/Srepeatedly until “5 DRC” appears,
then press ENTER (b).
3. Press W/S to set the DRC and then press
ENTER (b).
- DRC OFF : Deactivates this function.
1. Press RECEIVER, and then press SETUP.
"1 TESTTONE" appears on the display window.
2. Press W/Srepeatedly until “7 AUTO CAL”
appears, then press ENTER (b).
“TEST START” appears on the display window
and “START” blinks on the display window.
3. Proceed the steps 4 - 11 on the page 20.
4. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
- DRC ON : Activates this function.
,,Note
Audio dynamic range compression lets you
compress the dynamic range of the soundtrack
based on the dynamic range information
included in the Dolby Digital signal.
RESET menu
This allows you to initialize settings you have made
in the SETUP menu.
1. Press RECEIVER, and then press SETUP.
"1 TESTTONE" appears on the display window.
2. Press W/Srepeatedly until “8 RESET” appears,
then press ENTER (b).
“1 - YES 2 - NO” appears on the display window.
SET HDMI menu (HDMI
Standby Pass Trough)
3. Press the numeric 1 to reset the unit to its
original factory settings.
When the TV is turned on while the receiver is in
the standby mode, the sound and image is output
from the TV when you have played a component
connected to HDMI IN jack.
4. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
1. Press RECEIVER, and then press SETUP.
"1 TESTTONE" appears on the display window.
2. Press W/Srepeatedly until “6 SET HDMI”
appears, then press ENTER (b).
3. Press W/S to set the STDBY and then press
ENTER (b).
- STDBY OFF : Deactivates this function.
- STDBY ON : Activates this function.
4. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
If you don't want to reset it, press the numeric 2.
3
System Setting
4. Press RETURN to move to the previous menu.
Press SETUP to exit the SETUP menu.
4
Operating 24 Operating
Selecting the input
source
This section explains how to select the input source
(i.e., the AV component that you want to listen to or
watch).
1. Press 1 (POWER) to turn the unit on.
2. Press RECEIVER.
The button is illuminated.
3. Press INPUT buttons to select a source
The selected input appears on the display
window.
To activate the muting function
Press MUTE ( ) on the remote control. To cancel,
press MUTE ( ) on the remote control again or
rotate the VOLUME on the front panel.
Enjoying sound/images
from the components
connected to the
receiver
To select the
Button
Enjoying Blu-ray Disc/DVD
Blu-ray disc player, etc.,
connected to BD IN jack
BD
1. Turn on the TV.
4
DVD player, DVD recorder, etc.,
connected to DVD IN jack
DVD
Operating
Satellite tuner, set top box, etc,
connected to STB IN jack
STB
TV, etc., connected to OPTICAL
TV IN jack
TV
Game console, etc., connected
to OPTICAL GAME IN jack
GAME
CD player, etc., connected to
COAXIAL CD IN jack
CD
Built-in tuner
RADIO
VCR, etc., connected to AUDIO
VCR IN jack
VCR
Portable device (MP3 player,
etc.), connected to PORT. IN
jack
PORTABLE
IPod/USB device, connected to
IPod/USB Port
IPOD/USB
2. Turn on the Blu-ray Disc player or DVD player,
then place the disc on the tray.
3. Turn on the receiver.
4. Press BD or DVD.
You can also press FUNCTION on the front panel
to select “BD” or “DVD”.
5. Change the TV input.
For details, refer to the operating instructions of
the TV.
6. Play back the disc.
You can also press FUNCTION on the front
panel.
4. Turn on the component and start playback.
5. To adjust the volume, rotate the VOLUME on the
front panel, or press VOL +/- on remote control.
7. Adjust the volume of the receiver.
Operating 25
Enjoying a satellite tuner or
set top box
1. Turn on the TV.
2. Turn on the satellite tuner or set top box and
the receiver.
3. Press STB.
,,Note
yy The audio input of the TV is switched and
the image from the TV tuner is displayed on
the TV screen automatically by pressing the
TV button.
yy The sound may be output from the TV’s
speaker. In this case, turn the volume of the
TV’s speaker down to the minimum.
Enjoying a game console, etc
1. Turn on the component connected to OPTICAL
GAME IN jack.
2. Turn on the receiver.
3. Press GAME.
You can also press FUNCTION on the front panel
to select “STB”.
4. Change the TV input.
4
Operating
For details, refer to the operating instructions of
the TV.
5. Adjust the volume of the receiver.
Enjoying TV
1. Turn on the TV and choose a program.
For details, refer to the operating instructions of
the TV.
2. Turn on the receiver.
3. Press TV.
You can also press FUNCTION on the front panel
to select “TV”.
4. Adjust the volume of the receiver.
You can also press FUNCTION on the front panel
to select “GAME”.
4. Play back the component.
5. Adjust the volume of the receiver.
26 Operating
Enjoying a CD player, etc
1. Turn on the component connected to COAXIAL
CD IN jack.
2. Turn on the receiver.
3. Press CD.
You can also press FUNCTION on the front panel
to select “CD”.
4. Play back the component.
4
5. Adjust the volume of the receiver.
Operating
Enjoying a VCR, etc
Enjoying a portable device
(MP3 player, etc.)
1. Turn on the portable device (MP3 player, etc.)
2. Turn on the receiver.
3. Press PORTABLE.
You can also press FUNCTION on the front panel
to select “PORTABLE”.
4. Play back the component.
5. Adjust the volume of the receiver.
2. Turn on the receiver.
Enjoying the USB or iPod
connected to the IPod/USB
Port
3. Press VCR.
1. Turn on the receiver.
1. Turn on the component connected to AUDIO
VCR IN jack.
2. Press IPOD/USB.
You can also press FUNCTION on the front panel
to select “VCR”.
4. Change the TV input.
For details, refer to the operating instructions of
the TV.
5. Play back the component.
6. Adjust the volume of the receiver.
You can also press FUNCTION on the front panel
to select “USB” or “IPOD”.
3. Connect the USB or iPod.
4. Play back the USB or iPod.
5. Adjust the volume of the receiver.
Operating 27
Adjusting the speaker
levels
During playback, reinforces the
bass sound.
PLll MOVIE
Performs Dolby Pro Logic II Movie
mode decoding. This setting
is ideal for movies encoded in
Dolby Surround. In addition, this
mode can reproduce sound in 5.1
channel for watching videos of
overdubbed or old movies.
PLll MUSIC
Performs Dolby Pro Logic II Music
mode decoding. This setting is
ideal for normal stereo sources
such as CDs.
CLRVOICE
This mode makes voice sound
clear, improving the quality of
voice sound.
VIRTUAL
You can enjoy more virtual
surround sound.
GAME
Reproduces powerful and realistic
sound, suited for playing video
games.
NIGHT
You can enjoy sound effects and
hear the dialog clearly even at a
low volume level. This function is
useful for enjoying sound at night.
UPSCALER
Reproduces a clear enhanced
sound image from your portable
audio device. This mode is ideal for
MP3 and other compressed music.
LOUDNESS
Improves the bass and treble
sound.
ASC EQ
Enjoys the EQ (Equalizer) sound
according to measurement result
when the Auto Sound Calibration
has been completed.
You can adjust the level of each speaker to suit your
preference.
1. Press SPEAKER LEVEL.
"SW" appears on the display window.
2. Press A/D repeatedly to select a desired
speaker.
3. Press W/S to adjust the sound level of the
selected speaker while the indicator is displayed
on the display window.
Display
Description
SW
Subwoofer (- 40 ~ + 6)
FL
Front left speaker (- 6 ~ 0)
C
Center speaker (- 6 ~ + 6)
FR
Front right speaker (- 6 ~ 0)
SR
Surround right speaker (- 6 ~ + 6)
SL
Surround left speaker (- 6 ~ + 6)
4. Repeat and adjust the sound level of the other
speakers.
Enjoying various sound
mode
You can select a suitable sound mode. Press SOUND
repeatedly until the desired mode appears on the
front panel display or the TV screen. The displayed
items for the equalizer maybe different depending
on sound sources and effects.
Display
Description
NAT PLUS
You can enjoy the natural sound
effect same as a 5.1-channel.
NATURAL
You can enjoy comfortable and
natural sound.
BYPASS
You can enjoy the 2 channel sound
from front speakers and subwoofer.
4
Operating
BASS
28 Operating
Listening to FM radio
Presetting radio stations
You can listen to FM broadcast through the builtin tuner. Before operation, make sure you have
connected the FM antenna to the unit. (Page 18)
You can easily tune in the stations you often listen
to.
Automatic tuning
1. Press RADIO to select tuner (FM). The last
received station is tuned in.
You can also press FUNCTION on the front
panel.
2. Press TUNING - or TUNING + for more than 2
seconds.
4
Press TUNING - for more than 2 seconds to scan
from high to low.
Press TUNING + for more than 2 seconds to scan
from low to high. The unit stops scanning whenever a station is
received.
Operating
3. Adjust the volume by rotating VOLUME on
the front panel or by pressing VOL +/- on the
remote control.
Manual tuning
You can preset up to 50 FM stations.
1. Press RADIO to select tuner (FM). The last
received station is tuned in.
You can also press FUNCTION on the front
panel.
2. Tune in the station that you want to preset
using Automatic tuning or Manual tuning.
3. Press ENTER (b).
A preset number flashes on the display window
for a few seconds. When a preset number
flashes, do the step 4.
4. Press PRESET - or PRESET+ to select a preset
number you want.
If a preset number is not flashed before you
select the preset number, start again from the
step 3.
5. Press ENTER (b) again.
The station is stored to the selected preset
number. If a preset number is not flashed before
you press ENTER (b), start again from the step
3.
Press TUNING - or TUNING + briefly and repeatedly
on the FM mode to select a station you want.
6. Repeat the steps 2 to 5 to preset another
station.
Improving poor FM reception
Tuning to preset stations
Press B (blue) (MONO/STEREO) colored button on
the remote control. This will change the tuner from
stereo to mono and usually improve the reception.
Before tuning to preset stations, make sure you
preset radio stations.
1. Press RADIO to select tuner (FM). The last
received station is tuned in.
You can also press FUNCTION on the front
panel.
2. Press PRESET - or PRESET+ repeatedly to select
the preset station you want.
Each time you press the button, you can select
a preset station.
Operating 29
Deleting the preset stations
You can delete a preset station you want.
1. Press RADIO to select tuner (FM). The last
received station is tuned in.
You can also press FUNCTION on the front
panel.
Seeing information about a
radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about the
radio station being listened to. Press RDS repeatedly
to cycle through the various data types:
2. Select the preset station to delete by pressing
PRESET - or PRESET+.
Display
Description
3. Press CLEAR.
PTY
(Programme Type Recognition)
4. Press CLEAR again while the preset number
flashes on the display window for a few
seconds.
The preset station is deleted.
The programme type (e.g. Jazz or
News) will appear in the display.
RT
A text message contains special
information from the broadcast
station. This text may scroll across the
display.
5. Repeat the steps 2 to 4 to delete another preset
station.
Deleting all the preset stations
1. Press and hold CLEAR for about two seconds.
CT
PS
(Programme Service Name)
The name of the channel will appear
in the display
You can search the radio stations by programme
type by pressing RDS. The display will show the last
PTY in use. Press PTY one or more times to select
your preferred programme type. Press PTY SEARCH.
The tuner will search automatically, when a station
is found the search will stop.
4
Operating
All the preset stations are cleared.
(Time controlled by the channel)
This shows the time and date as
broadcast by the station.
“ERASE ALL” appears on the display window.
2. Press CLEAR again while “ERASE ALL” is displayed.
(Radio Text)
30 Operating
Playing back
components with onetouch operation (OneTouch Play)
By a simple operation (one touch), the TV is
switched to the HDMI mode.
1. Connect a component and the receiver with
HDMI connections.
2. Select the connected HDMI source.
3. Play back a connected component.
The TV is turned on automatically and switched
to the HDMI mode.
,,Note
4
The One-Touch Play may not be supported
depending on the TV. For details, refer to the
operating instructions of the TV.
Enjoying the TV sound
from the speakers
connected to the
receiver (System Audio
Control)
Operating
You can enjoy the TV sound from the speakers
connected to the receiver by a simple operation.
You can operate System Audio Control function
using the TV menu. For details, refer to the
operating instructions of the TV.
When System Audio Control function is turned
on, the receiver will turns on and switches to the
appropriate input automatically. (If the TV supports ARC (Auto Return Channel)
function, the receiver is changed to the “ARCHDMI”. If the TV does not support ARC (Auto Return
Channel) function, the receiver is changed to the
“TV-OPT”.) TV sound is output from the speakers connected to
the receiver, and the volume of the TV is minimized
simultaneously.
You can use the System Audio Control function as
follows.
yy If you turn off the receiver, the sound will output
from the TV speakers.
yy You can adjust the receiver’s volume when you
adjust the TV volume.
,,Note
yy If System Audio Control does not function
according to your TV setting, refer to the
operating instructions of the TV.
yy When you connect a TV that does not have
System Audio Control function, the System
Audio Control function does not work.
Operating
Turning off the
receiver with the TV
(System Power Off)
When you turn the TV off by using the POWER
button on the TV’s remote control, the receiver
turns off automatically. But the receiver will not turn
off in IPOD, USB, and RADIO mode.
Some TV may not support this function. For details,
refer to the operating instructions of the TV.
Enjoying the TV
sound via an HDMI
connection (Audio
Return Channel)
1. Press ARC.
2. To cancel it, choose a different function mode.
,,Note
yy This function is available only when the
Control for HDMI function is set to on.
yy Be sure that your TV is compatible with
Audio Return Channel (ARC) function.
For details on the TV settings, refer to the
operating instructions of the TV.
Adjusting the audio
delay
You can delay the sound output using this function
when the image is slower than the sound.
1. Press AV SYNC..
The current settings is showed on the display
window.
2. Press W/S to adjust the delay between
sound and image while the current settings are
showed on the display window.
You can adjust from 0 MS to 300 MS in 10 MS
steps.
,,Note
yy You may not be able to adjust the delay
between sound and image perfectly using
this function.
yy This function is useful only for Dolby Digital,
DTS and Linear PCM (2ch) input by optical
and coaxial audio input signals.
DOLBY DRC (Dynamic
Range Control)
This function allows you to listen to a movie at a
lower volume without losing clarity of sound. You
can compress the dynamic range of the Dolby
Digital audio output.
Press DOLBY DRC repeatedly.
The current settings is showed on the display
window.
- DRC OFF : Deactivates this function.
- DRC ON : Activates this function.
,,Note
Audio dynamic range compression lets you
compress the dynamic range of the soundtrack
based on the dynamic range information
included in the Dolby Digital signal.
4
Operating
The receiver can receive the audio signal of the
TV via an HDMI cable (High speed HDMI™ cable
with Ethernet) when your TV is compatible with
the Audio Return Channel (ARC) function. You
can enjoy TV sound via the receiver by using just
one HDMI cable (High speed HDMI™ cable with
Ethernet).
31
32 Operating
Using the Sleep Timer
You can set the unit to turn off automatically at a
specified time.
Press SLEEP repeatedly.
The minutes display (the remaining time) changes
cyclically on the display window as follows.
DIMMER t SLEEP 180 t 150 t 120 t 90 t
80 t 70 t 60 t 50 t 40 t 30 t 20 t
10 t OFF (No display)
To check the remaining time, press SLEEP. The
remaining time appears on the display window.
To cancel the sleep function, press SLEEP repeatedly
until “SLEEP 10” appears, and then press SLEEP once
again while “SLEEP 10” is displayed.
,,Note
4
When you press SLEEP, the *DIMMER function
is set.
Operating
* DIMMER function: The brightness of the
display window is darken by half.
When you press SLEEP again, the Sleep Timer
function is set.
Displaying the file
information
You can display various information on the display
window by pressing INFO/DISPLAY (m).
Input source
Description
BD, DVD, STB, TV,
GAME, or CD
Displays the audio format
and audio channel. (“PCM
2/0.0”, “DD 3/2.1”, “DTS3/2.1”,
or “AAC3/2.1”)
VCR or PORTABLE
"ANALOG" is displayed.
USB
Displays the file information
during MP3/WMA playback.
IPOD
Displays the title, artist and
album.
,,Note
If there is no input source, the “-- 0/0.0”
appears on the display window.
Operating 33
Playing music files
using the USB device
You can play music files contained in the USB
device.
Basic Operation
Music file requirement
Music file compatibility with this unit is limited as
follows:
yy Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate : within 32 to 320 kbps (MP3), 40 to 192 kbps (WMA)
yy Support Version : v2, v7, v8, v9
1. Insert a USB device to the IPod/USB Port until it
fits into place.
yy Maximum files : Under 999
2. Press IPOD/USB.
yy We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
The total number of files is displayed on the
display window.
3. Referring to the following table, press the
corresponding button for the operation.
Description
d (PLAY)
Starts playback.
M (PAUSE)
Pauses playback.
Z (STOP)
Stops playback.
C/V
(SKIP)
During playback, press C or
V to go to the next file or
to return to the beginning of
the current file.
Press C twice briefly to step
back to the previous file.
c/v
(SCAN)
During playback, press and
hold c or v and then
release at a point you want.
Playing repeatedly or randomly
Press REPEAT (h) on the remote control
repeatedly during playback.
Display
Description
OFF
Returns to normal playback.
RPT 1
Plays the current file repeatedly.
RPT D
Plays all the files repeatedly within a
folder.
RPT ALL
Plays all the files repeatedly.
RANDOM
Plays all the files in random order.
USB device requirement
yy A device using NTFS file system is not supported.
(Only FAT (12/16/32) file system is supported.)
yy Do not extract the USB device during operation
(play, etc.).
yy A USB device which requires additional program
installation when you have connected it to a
computer, is not supported.
yy USB device: USB device that supports USB1.1.
yy Regular back up is recommended to prevent
data loss.
yy If you use a USB extension cable, USB HUB or
USB Multi-reader, the USB device may not be
recognized.
yy Some USB device may not work with this unit.
yy Digital camera and mobile phone are not
supported.
yy IPod/USB Port of the unit cannot be connected
to PC. The unit cannot be used as a storage
device.
yy When you connect a partitioned USB device into
the unit, only the fi rst partition is recognized on
it.
4
Operating
Remote control
buttons
yy File extensions : “.mp3”/ “.wma”
34 Operating
Playing the iPod
REPEAT
You can enjoy the sound with your iPod. For details
about iPod, refer to the iPod’s User Guide.
Before connecting the iPod, turn this unit off and
reduce the volume of this unit to its minimum.
1. Insert your iPod to the IPod/USB Port until it fits
into place.
Your iPod is automatically turned on and
recharging starts.
2. Press IPOD/USB.
"IPOD READY" appears for about 3 seconds and
then the current playback status is displayed on
the display window.
3. Operate your iPod by using the supplied remote
control and controls on your iPod.
4
REPEAT
During playback, press
REPEAT repeatedly to
select a desired repeat
mode. (OFF t RPT 1
t RPT AL t
RANDOM)
,,Note
yy It works with all iPod models (except for the
models produced before 2004) that have a
dock connector.
yy Compatibility with your iPod may vary
depending on the type of your iPod.
yy Depending on your iPod’s software version,
it may not be possible to control your iPod
from the unit. We recommend installing the
latest software version.
Operating
Description
yy Adjust the volume to a moderate level
before you connect your iPod and this unit.
dM
Starts playback.
dM
Pauses playback.
yy If the unit occurs the lack of power supply,
communication failure, or contact faulty,
the iPod error message is displayed on the
display window.
Z (STOP)
-
Stops playback.
C/V
(SKIP)
C/
V
During playback,
press C or V
to go to the next file
or to return to the
beginning of the
current file.
Remote
control
buttons
iPod
d (PLAY)
M (PAUSE)
buttons
Press C twice
briefly to step back to
the previous file.
c/v
(SCAN)
c/
v
During playback,
press and hold c or
v and then release
at a point you want.
DISC MENU
MENU
Returns to the upper
menu in iPod mode.
W/S
Click
wheel.
Moves to an item in
the menu.
yy Interference may happen depending on
iPod devices.
yy iPod touch and iPhone have any difference
in operation other than iPod. You may need
any additional control to use them with this
unit. (e.g. “slide to unlock”)
yy Compatible iPod models
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th generation)
- iPod 5th generation
- iPod touch (1st, 2nd, 3rd, 4th generation)
- iPhone (3rd, 4th generation), iPhone 3GS
yy If you have a problem with your iPod, please
visit www.apple.com/support/ipod.
Operating 35
Controlling a TV with
the Supplied Remote
Control
Setting up the remote to
control your TV
You can control your TV using the buttons below.
2. Press TV on the remote control to enter the TV
mode.
You can operate your TV with the supplied remote
control.
1. Turn the TV on.
3. Press and hold TV for about 3 seconds until the
TV button can be seen illuminated.
4
You can
1 (POWER)
Turn the TV on or off.
0-9 numerical
buttons:
Selects numbered options in
a menu or inputs letters in the
keypad menu.
TV INPUT
Select the TV’s source.
MUTE (
)
Turns off the sound temporarily.
Press the button again to
restore the sound.
PR/CH W/S
Scan up or down through
memorized channels.
VOL +/–
Adjust the volume of the TV.
,,Note
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
4. Press the manufacturer code for your TV with
the numerical buttons (three digit code).
See the manufacturer code list on the pages 3843.
5. Press the ENTER (b) button to complete
setting.
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may
be reset to the default setting. Set the appropriate
code number again.
Operating
By pressing
5
Troubleshooting
36 Troubleshooting
Troubleshooting
Symptom
Cause
Solution
The Power does not turned on.
The power cord is
disconnected.
Plug the power cord into the wall outlet
securely.
No sound.
yy The speaker wires are
disconnected.
yy Check the speaker connections.
yy The speaker volume is
adjusted too low.
yy Adjust the speaker volume.
yy The MUTE button is
pressed to ON.
yy Press the MUTE button to cancel the
muting effect.
yy The selected decoding
mode is not matched to
the input signal format.
yy Select the available decoding mode.
yy Incorrect selection of
input source.
yy Select the desired input source
correctly.
yy Incorrect connections
between the
components.
yy Make connections correctly.
yy The antenna is
positioned or connected
poorly.
yy Check the antenna connection and
adjust its position.
yy The signal strength of
the radio station is too
weak.
yy Tune to the station manually.
yy No stations have been
preset or preset stations
have been cleared (when
tuning by scanning
preset channels).
yy Preset some radio stations, see page
28 for details.
yy An incorrect station
frequency has been
memorized.
yy Memorize the correct station
frequency.
yy The memorized stations
are cleared.
yy Memorize the stations again.
yy No antenna is connected.
yy Connect the antenna.
yy The antenna is not
positioned for the best
reception.
yy Change the position of the antenna.
Radio stations can’t be tuned
in properly.
5
Troubleshooting
Preset stations cannot be
received.
Poor FM reception.
Troubleshooting 37
The remote control doesn’t
work well / at all.
yy The remote control is not yy Point the remote directly at the unit
pointed directly at the
unit.
yy The remote control is too
far from the unit.
yy Use the remote within 23 feet (7m) of
the unit.
yy There is an obstacle in
the path between the
remote control and the
unit.
yy Remove the obstacle.
yy The battery in the remote
control are flat.
yy Replace the batteries with new ones.
yy The correct input mode
(RECEIVER, PLAYER, or TV
mode) is not selected on
the remote control.
yy Select the correct input mode
(RECEIVER, PLAYER, or TV mode). For
details, see "About the remote control
modes" on the page 7.
5
Troubleshooting
38 Appendix
Manufacturer code list
Choose a manufacturer code from this list.
6
Manufacturer
Code Number
Manufacturer
Code Number
ADMIRAL
137, 204
BRIONVEGA
204
ADYSON
159, 219
BSR
144
AKAI
009, 010, 038, 108, 132, 133, 135,
139, 140, 156, 174, 175
BUSH
009, 136, 139, 144, 232
AKURA
064, 086, 108, 110, 155, 171
CENTURY
165, 204
ALBA
009, 060, 064
CGE
139, 165, 210
ALLSTAR
108
CIE
025, 108, 170
AMSTRAD
006, 025, 157
CLATRONIC
009, 010, 064, 108, 144, 149,
159, 164, 165, 171, 185
Appendix
AMWAY
108
CLARIVOX
031
ANITECH
010, 049, 108, 185, 219
CONDOR
108, 149, 191
ANTECNO
064
CONIC
219
ARC EN CIEL
173, 179, 239
CONTEC
171, 222
ASA
087, 102, 108, 235, 236
CONTINENTAL
EDISON
173, 179, 225, 239
ASBERG
185
COSMOS
108
ASORA
171
CROSLEY
165 204
ATLANTIC
089, 197
CROWN
084, 085, 086, 108, 144, 171,
185
AUDIOSONIC
085
CS-ELECTRONICS
064
AUTOVOX
159, 163, 197
DAEWOO
051, 108, 120, 127, 170
BANK
232
DANSAI
010, 219
BEKO
045, 085, 086, 108, 250
DE GRAAF
108 134
BESTAR
086
DECCA
070, 108, 159, 161, 162, 184,
189, 190, 206
BLAUPUNKT
091, 092, 096, 097, 098, 099, 210,
253
DECCAVIDEO
108
BONDSTEC
163
DUAL
233
BOSCH
210
DUMONT
204
BRANDT
ELECTRONIQUE
173, 179, 225, 239
ELBE
058, 144, 157, 160, 192, 246
Appendix 39
Manufacturer
Code Number
Manufacturer
Code Number
ELBIT
108, 248
FUJITSU
GENERAL
088, 159, 197
ELECTROVENDA
108
FUNAI
010
ELEKTRONIKA
108
GALAXIS
108, 185
ELIN
108
GALERIA
171
ELITE
064, 149
GBC
137, 144, 171
ELMAN
144
GEC
011, 108, 129, 147, 159, 189
ELTA
010, 171
GELOSO
064, 137, 144, 164, 171
EMERSON
108, 204
GENERAL
171
ESC
108
GENERAL
TECHNIC
171
ETRON
133
GOLDHAND
159, 171
EUROPHON
144, 159
GOLDSTAR
001, 050, 108, 110, 136, 144,
159, 163, 166, 171, 191, 219, 237
EXPERT
089
GOODMANS
009, 064, 108, 109, 110, 120,
159, 170, 171
FENNER
171
GORENJE
086
FERGUSON
078, 079, 080, 160, 182, 195, 198,
199, 200, 201, 202
GPM
010, 064
FINLANDIA
194, 195
GRANADA
027, 105, 108, 111, 121, 134,
140, 159, 162, 167, 187, 194,
195, 238
6
FINLUX
008, 087, 102, 104, 105, 107, 108
140, 144, 159, 161, 174, 189, 235,
236
GRUNDIG
091, 092, 093, 094, 095, 097,
098, 100, 101, 172, 232, 238
Appendix
FIRST-LINE
144
HCM
010, 108, 159, 171
FISHER
086, 208, 222, 233
HIFIVOX
173, 179, 239
FORMENTI
108, 149
HINARI
010, 064, 108, 133, 171
FRABA
108
HIT
204
FRONTECH
136, 171, 220
HITACHI
011, 013, 015, 017, 021, 022,
023, 024, 028, 029, 030, 035,
039, 040, 041, 048, 053, 054,
055, 056, 057, 120, 127, 128,
129, 134, 135, 140, 143, 145,
147, 151, 156, 159, 173, 193,
219
FUBA
073, 109
HYPER
009, 159, 163, 171
40 Appendix
6
Appendix
Manufacturer
Code Number
Manufacturer
Code Number
ICE
009, 010, 064, 108, 171
LENCO
108 170
IMPERIAL
043, 049, 108, 139, 144, 154, 165,
255 LG
001 (Default code), 050, 108,
110, 136, 144, 159, 163, 166,
171, 191, 219, 237
INGERSOLL
171
LIESENKOTTER
108, 210
INNO HIT
159, 189, 237
LIFETEC
010, 064, 108, 170
INTERBUY
010
LOEWE
109, 113, 204, 205
INTERCORD
233
LOGIK
070, 227
INTERFUNK
108, 109, 113, 130, 133, 134, 135,
137, 141, 146, 147, 148, 165, 179,
210
LUMA
137, 197
INTERVISION
010, 086, 108, 132, 144, 166
LUXOR
102, 104, 132, 133, 134, 135,
138, 140, 143, 145, 153, 156,
174, 186, 237
IRRADIO
163, 235, 237
M ELECTRONIC
103, 104
ITC
144, 159
MAGNADYNE
163, 164, 204
ITS
009, 010, 064, 171
MAGNAFON
199
ITT
141, 151, 186
MAGNASONIC
108
JVC
009, 169
MARANTZ
108
KAPSCH
089, 147, 148, 197
MARSHAL
064
KARCHER
084, 108
MATSUI
009, 016, 025, 060, 061, 062,
063, 070, 108, 131, 136, 152,
154, 159, 171, 172
KATHREIN
109
MERRIT
132
KAWA
009
METZ
047, 092, 097, 098, 100, 101,
108, 204, 207, 254
KENDO
060, 108, 137, 157
MITSUBISHI
075, 076, 077, 097, 113, 204,
222, 224, 240
KENNEDY
197
MIVAR
044, 159, 235
KNEISSEL
108
MNARTT
007
KORTING
086, 204, 209
MTC
086, 109, 134
KUBA
233
MULTITECH
136, 159, 171, 185
KUBA ELECTRONIC
233
MURPHY
232
KURA
134
NAONIS
137
Appendix
Manufacturer
Code Number
Manufacturer
Code Number
NECKERMANN
037, 059, 060, 092, 098,
100, 101, 108, 109, 113,
115, 118, 119, 134, 135,
137, 143, 157, 159
PAEL
235
NEI
064, 108
PANASONIC
002, 003, 005, 167, 168, 229
NIKKAI
219
PATHE CINEMA
144
NIKKO
108
PHILCO
090, 108, 139, 144, 148, 165,
204
NOBLIKO
232, 235
PHILIPS
065, 066, 067, 068, 069, 092,
108, 109, 111, 112, 114, 115,
116, 119, 122, 123, 124, 125,
193, 212, 251 252
NOGAMATIC
173, 179, 239
PIONEER
193
NOKIA
014, 019, 032, 102, 103,
104, 108, 132, 133, 134,
135, 138, 140, 141, 145,
146, 147, 148, 156, 174
PRANDONIPRINCE
137, 235
NORDMENDE
129, 173, 179, 180, 181,
193, 195, 225, 226, 228,
239
PRIMA
219
NORMN
108
PRO VISION
108
NOVA
087
PROFEX
108, 136, 171
OCEANIC
032, 103, 104, 135, 140,
156
PROFITRONIC
108
108
QUELLE
ONWA
009, 010, 064
RADIOLA
108
ORAVA
108
RADIOTONE
010, 085, 108, 171
ORBITER
086
REDIFUSSION
187
ORION
025, 059, 060, 061, 062,
064, 070, 108, 110, 118,
219,
REVOX
109
OSAKE
106
REX
088, 089, 137, 157, 158, 164,
197, 246, 247
OTTO-VERSAND
002, 005, 009, 014, 059,
060, 081, 082, 083, 085,
092, 097, 098, 100, 101,
108, 109, 111, 113
RFT
064, 085, 135, 204
6
Appendix
OKANO
002, 010, 014, 019, 025, 038,
059, 060, 072, 084, 086, 087,
088, 092, 097, 098, 100, 101,
102, 175,
41
42 Appendix
6
Appendix
Manufacturer
Code Number
Manufacturer
Code Number
RITAR
138
SILVER
010, 064
ROADSTAR
108
SINGER
108, 164, 204
ROSITA
171
SINUDYNE
118, 131
SABA
079, 146, 147, 173, 179,
181, 193, 195, 225, 226,
239
SMARAGO
172
SAISHO
025, 060, 070, 136, 159
SOLAVOX
133
SAKIO
171
SONOLOR
140 156
SALORA
019, 032, 103, 104, 132,
133, 134, 135, 137, 138,
140, 142, 143, 145, 150,
156, 174, 237, 241
SONTEC
108
SAMBERS
235
SONY
072, 074, 211, 212, 213, 214,
215, 216, 217, 222
SAMSUNG
004, 010, 050, 086, 108,
117, 126, 171, 220, 237
SPECTRA
170
SANY
193
STARLITE
108, 171
SANYO
014, 018, 019, 020, 032,
034, 071, 086, 087, 189,
218, 221, 222, 223
STARLUX
171
SCHNEIDER
009, 064, 088, 108, 133,
141, 159, 163, 233
STERN
088, 089, 137, 157, 197
SEG
010, 064, 108, 144, 159,
165, 171, 185, 219
SUNSTAR
108, 171
SEI-SINUDYNE
025, 108, 204, 212
SUPERTECH
108, 139, 152, 171
SELECO
088, 089, 137, 157, 197,
222
TADISTAR
108
SENTRA
064, 133
TASHIKO
108
SHARP
081, 082, 083, 222
TASHIKO
159, 218
SHINTOM
108
TEC
108, 139, 144, 159, 170, 171
SHINTOSHI
108
TECHLINE
185
SHIVAKI
108
TECHNISAT
108, 165
SIAREM
204
TECNISON
108, 171
SIEMENS
092, 096, 097, 098, 100,
101, 108, 210, 218, 219,
221
TEKON
171
SIESTA
085
TELEAVIA
173, 178, 179, 225, 239
Appendix 43
Code Number
Manufacturer
Code Number
TELEFUNKEN
079, 177, 179, 181, 193,
195, 200, 210
UHER
089, 108, 109, 149, 185, 197,
233
TELEOPTA
171
ULTRAVOX
108, 164, 185, 204
TELERNT
109
UNIVOX
204
TELETECH
165, 171
VESTEL
108
TELETEXT
115
VIDEOSAT
165
TELETON
088
VIDEOTON
178, 193
TELETON
089, 134, 159, 197
VIDEOWAY
230
TENSAI
064, 108, 144, 149, 171,
191
VISION
108, 149
TENSON
171
VOXSON
137, 204
TESLA
204
WALTHAM
178
THOMSON
052, 078, 079, 134, 173,
178, 179, 181, 193, 195,
225, 239
WATSON
064, 108, 149, 171
THORN
011, 014, 016, 018, 026,
028, 066, 072, 075, 087,
097, 102, 108, 116, 135,
141, 145, 146, 160
WEGA
208, 222
THORN-FERGUSON
160, 188, 200, 227
WHITE
WESTINGHOUSE
108 110 149
TOSHIBA
012, 016, 026, 036, 037,
222, 232
YOKO
010, 064, 108, 136, 144, 159,
164, 170, 171
TOWADA
144, 185
ZANUSSI
137, 197
TRISTAR
010, 064
ZENITH
231
TRIUMPH
025, 219, 236
6
Appendix
Manufacturer
44 Appendix
Trademarks and
Licenses
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by the
developer to meet Apple performance standards.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the double-D
symbol are trademarks of Dolby Laboratories.
“Works with iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhone and has been certified
by the developer to meet Apple performance
standards.
Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
iPhone is a trademark of Apple Inc.
Manufactured under licence under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and the Symbol are
registered trademarks & DTS Digital Surround
and the DTS logos are trademarks of DTS, Inc.
Product includes software. © DTS, Inc. All Rights
Reserved.
6
Appendix
Appendix 45
Specifications
General
Power requirements
Refer to main label on the rear panel.
Power consumption
Refer to main label on the rear panel.
Dimensions (W x H x D)
Approx. 430 x 60 x 243.5 mm (16.9 x 2.4 x 9.2 inches)
Net Weight (Approx.)
2.9 kg (6.4 lbs)
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Bus Power Supply (USB)
DC 5 V 0 1 A
Inputs/Outputs
HDMI IN/OUT (video/audio)
19 pin (Type A, HDMI™ Connector)
ANALOG AUDIO IN
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
DIGITAL IN (OPTICAL)
3 V (p-p), Optical jack x 2
DIGITAL IN (COAXIAL)
3 V (p-p), Coaxial jack x 1
PORT. IN
0.5 Vrms ( 3.5 mm stereo jack)
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Amplifier
Power output (4 Ω/ 3 Ω), (RMS), THD 10 %
1100 W
Front
180 W x 2
Center
180 W
Rear
180 W x 2
Sub-Woofer
200 W (Passive)
6
Appendix
Total
46 Appendix
Speakers
Front speaker (Left/ Right)
Type
2 Way 2 speaker
Max. Input power
360 W
Impedance Rated
4Ω
Net Dimensions (W x H x D)
94 x211 x83 mm (3.7 x 8.3 x 3.3 inches)
Input Power
180 W
Net Weight
0.7 kg (1.5 lbs)
1 Way 1 speaker
Max. Input power
360 W
Impedance Rated
4Ω
Net Dimensions (W x H x D)
94 x 182 x 83 mm
(3.7 x 7.2 x 3.3 inches)
Input Power
180 W
Net Weight
0.61 kg (1.34 lbs)
2 Way 3 speaker
Max. Input power
360 W
Impedance Rated
4Ω
Net Dimensions (W x H x D)
327 x 99 x 76 mm (12.9 x 3.9 x 3.0 inches)
Input Power
180 W
Net Weight
1.21 kg (2.67 lbs)
1 Way 1 speaker
Max. Input power
400 W
Impedance Rated
3Ω
Net Dimensions (W x H x D)
190 x 385 x 318 mm (7.5 x 15.2 x 12.5 inches)
Input Power
200 W
Net Weight
5 kg (11 lbs)
Rear speaker (Left/ Right)
Type
Center speaker
Type
Subwoofer
Type
yy Design and specifications are subject to change without notice.
6
Maintenance
Appendix
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
yy Do not use volatile liquids such as insecticide
spray near the unit.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the receiver, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
Warranty 47
Technology with the human touch
GUARANTEE
• LG Electronics U.K. Ltd. will provide the following services in order toexpedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a
period of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be reimbursed for any labour provided in the
repair of this LG equipment, for a period of 12 months from the original date of purchase. These claims
must be made in accordance with the published scale of service charges and relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made
to the apparatus, or if non standard components are used or if the serial number of the apparatus is
removed, defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a receipted
account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become
exhausted or worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
• REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:RETAIN YOUR RECEIPT TO PROVE DATE OF
PURCHASE. A COPY OF YOUR RECEIPT MUST BE SURRENDERED AT THE TIME GUARANTEE SERVICE IS
PROVED.
• Product Registration Card :
It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This
will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should
modifications be necessary.
• To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm
MODEL NO.*
SERIAL NO.*
DATE OF PURCHASE.*
LGEUK Website : www.lg.com
( service website : www.lgservice.com)
Warranty
In all cases of difficulty - consult your LG dealer from whom the product was purchased
7
Download PDF

advertising