ENGLISH
OWNER’S MANUAL
Micro Hi-Fi System
Please read this manual carefully before operating
your set and retain it for future reference.
FOR THE GUARANTEE TERMS & CONDITIONS, PLEASE REFER TO
INNER PAGE OF BACK COVER.
CM2630DAB (CM2630DAB, CMS2630FH)
CM2630-BR_DGBRLLK_ENG_6405.indd 1
2013-03-21
6:28:48
1
Getting Started
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CM2630-BR_DGBRLLK_ENG_6405.indd 2
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not
try to open the enclosure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
2013-03-21
6:28:48
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Disposal of your old appliance
1.When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/EC.
2.All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or
the local authorities.
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled
bin symbol is attached to batteries/
accumulators of Your product
it means they are covered by
European Directive 2006/66/EC.
2. This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the
battery Contains more that 0.0005%
of mercury,0.002% of cadmium or
0.004% of lead.
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
3. All batteries/accumulators should
be disposed separately from
the municipal waste stream via
designated collection facilities
appointed by the government or
the local authorities.
4. The correct disposal of Your old
batteries/accumulators will help
to prevent potential negative
consequences for the environment,
animal and human health.
5. For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your
city office, waste disposal service or
the shop where You purchased the
product.
3.The correct disposal of your
old appliance will help prevent
potential negative consequences
for the environment and human
health.
4.For more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.
CM2630-BR_DGBRLLK_ENG_6405.indd 3
2013-03-21
6:28:48
4
1
Getting Started
Getting Started
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC, 2004/108/EC, 2006/95/EC,
2009/125/EC and 2011/65/EU.
Please contact to the following address for
obtaining a copy of the DoC (Declaration of
Conformity).
Contact office for compliance of this product:
LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands
yy Please note that this is NOT a Customer
Service contact point. For Customer Service
Information, see Warranty Card or contact the
dealer that you purchased this product.
In door use only.
RF Radiation Exposure Statement
This equipment should be installed and operated
with minimum distance 20cm between the
radiator and your body.
LG Bluetooth Remote
You can control this player with your iPhone or
Android phone via Bluetooth. This player and your
phone must be connected to Bluetooth. Visit
“ Apple App Store” or “Google Android Market
(Google Play Store)” . And use this QR code to
search for “LG Bluetooth Remote” app. For detailed
information, refer to the 24 page.
CM2630-BR_DGBRLLK_ENG_6405.indd 4
POWER: This unit operates on a mains supply
of 200-240V~, 50/60Hz.
Wiring: This unit is supplied with a BS 1363
approved main plug. When replacing the fuse,
always use of the same rating approved to BS
1362. Never use this plug with the fuse cover
omitted. To obtain a replacement fuse cover
contact your dealer. If the type of plug supplied
is not suitable for the mains sockets in your
home, then the plug should be removed and
a suitable type fitted. Please refer to the wiring
instructions below:
Warning: A mains plug removed from the mains
lead of this unit must be destroyed. A mains
plug with bared wires is hazardous if inserted in
a mains socket. Do not connect either wire to
the earth pin, marked with the letter E or with
the earth symbol 6 or coloured green or green
and yellow. If any other plug is fitted, use same
rating of fuse in the plug.
Important: The wires in this mains lead are
coloured in accordance with the following
codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the
colours of the wires in the mains lead of this unit
may not correspond with the coloured marking
identifying the terminals in your plug, proceed
as follows: The wire which is coloured blue must
be connected to the terminal which is marked
with the letter N or coloured black. The wire
which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
2013-03-21
6:28:48
Table of Contents
Table of Contents
1
Getting Started
2
Safety Information
6
Unique Features
6Accessories
7
Playable file Requirement
8
Remote Control
9
Front Panel
10 Rear Panel
18
18
18
19
19
20
20
20
20
20
22
22
– Deleting all of the saved DAB scan
stations
Sound adjustment
– Setting the sound mode
Setting the Clock
– Using your player as an alarm clock
– Sleep Timer Setting
– Dimmer
Advanced Operation
– Recording on USB
– To select recording bit rate and speed
Using a Bluetooth wireless technology
– Listening to music of a Bluetooth
device
Using LG Bluetooth Remote app
2Connecting
24
11
11
11
12
12
12
13
14
14
14
4Troubleshooting
Connecting to speakers
– Attaching the speakers to the unit
Antenna Connection
Optional Equipment Connection
– USB Connection
– PORT. IN Connection
– PHONES Connection
Basic Operations
– CD/USB Operations
– Selecting a folder and an MP3/WMA
3Operating
15
15
15
16
16
16
16
16
16
16
17
17
17
18
18
18
Other Operation
– Programmed Playback
– Deleting an MP3/WMA file
– Displaying file information
– Turn off the sound temporarily
– DEMO
– Auto Power Down
Radio Operations
Listening to the radio
– Improving poor FM reception
– Presetting the Radio Stations
– Deleting all the saved stations
– Seeing information about a Radio
station
– Listening to the DAB
– Aligning the service names
– DAB scan
CM2630-BR_DGBRLLK_ENG_6405.indd 5
5
26Troubleshooting
1
2
3
4
5Appendix
27 Trademarks and Licenses
28Specifications
29Maintenance
29 – Notes on Discs
29 – Handling the Unit
5
6
6Warranty
30Warranty
2013-03-21
6:28:48
6
Getting Started
Unique Features
1
USB Direct Recording
Accessories
Please check and identify the supplied accessories.
Getting Started
Records music to your USB device.
Portable In
Listens to music from your portable device. (MP3,
Notebook, etc)
Remote Control (1)
Battery (2)
FM Antenna (1)
DAB antenna (1)
Timer
Sets alarm which go off at desired time.
Bluetooth®
Listens to music stored on your Bluetooth device.
Time Sync
Sets your unit’s clock automatically by using your
Bluetooth device. (LG Bluetooth Remote app)
CM2630-BR_DGBRLLK_ENG_6405.indd 6
2013-03-21
6:28:49
Getting Started
Playable file
Requirement
Compatible USB Devices
yy MP3 Player : Flash type MP3 player.
SB Flash Drive :
yy U
Devices that support USB2.0 or USB1.1.
MP3/ WMA file compatibility with this unit is limited
as follows :
USB device requirement
it rate : within 8 to 320 kbps (MP3),
yy B
40 to 192 kbps (WMA)
yy Maximum files : Under 999
evices which require additional program
yy D
installation when you have connected it to a
computer, are not supported.
1
Getting Started
MP3/ WMA music file requirement
yy T he USB function of this unit does not support
all USB devices.
yy S ampling frequency : within 8 to 48 kHz (MP3),
within 8 to 48 kHz (WMA)
7
yy Do not extract the USB device while in operation.
yy File extensions : “.mp3”/ “.wma”
yy F or a large capacity USB, it may take longer than
a few minutes to be searched.
yy CD-ROM file format : ISO9660/ JOLIET
yy To prevent data loss, back up all data.
yy You have to set the disc format option to
[Mastered] in order to make the discs compatible
with the LG players when formatting rewritable
discs. When setting the option to Live File
System, you cannot use it on LG players.
(Mastered/ Live File System : Disc format system
for Windows Vista)
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
sing NTFS file system is not supported. (Only
yy U
FAT(16/ 32) file system is supported.)
yy T his unit is not supported when the total
number of files is 1 000 or more.
yy E xternal HDD, Card readers, Locked devices, or
hard type USB devices, mobile phone are not
supported.
SB port of the unit cannot be connected to PC.
yy U
The unit cannot be used as a storage device.
yy Some USB may not work with this unit.
CM2630-BR_DGBRLLK_ENG_6405.indd 7
2013-03-21
6:28:49
8
Getting Started
Remote Control
• • • • • • a • • • • • •
1
Getting Started
1 (Power): Switches the unit
ON or OFF.
B (Open/Close) : Ejects the disc
from slot loader.
PRESET.FOLDER W/S :
-- Searches for a folder of MP3/
WMA files. When a CD/USB
containing MP3/WMA files in
several folders is being played,
press PRESET.FOLDER W/S
to select the folder you want
to play.
USB REC
DELETE
DELETE : Deletes MP3/WMA
files. (USB only)
FUNCTION : Selects the
function and input source.
• • • • • • c • • • • • •
VOL +/- : Adjusts speaker
volume.
• • • • • • b • • • • • •
PROGRAM/MEMORY :
- Stores radio stations.
- Creates a playlist you want to
listen to.
SOUND EFFECT : Chooses
sound impressions.
Battery Installation
INFO : Sees information about
your music. MP3 files often
come with ID3 tags. The tag
gives the Title, Artist, Album or
Time information.
REPEAT (MENU) : Listens to
your tracks/files repeatedly or
randomly.
Remove the battery cover
on the rear of the Remote
Control, and insert two (size
AAA) batteries with 4 and 5
matched correctly
CM2630-BR_DGBRLLK_ENG_6405.indd 8
USB REC : Starts recording
-- Chooses a preset number for
a radio station.
MUTE @ : Mutes the sound.
TIMER
ZENTER :
- Stops playback or recording.
- Cancels DELETE function.
- Confirms the clock and the
alarm setting
d/M (Play/Pause) :
- Starts or pauses playback.
- Starts or pauses playback.
SLEEP : Sets the system to turn
off automatically at a specified
time.(Dimmer : The display
window will be darkened by
half.)
C/V (Skip/Search) :
-Skips Fast backward or Forward.
-Searches for a section within a
track/file.
CH/TUNING -/+ :
- Selects a DAB display mode.
- Selects the radio stations.
0 to 9 numerical buttons :
Selects numbered tracks, files, or
preset number.
CLOCK : Sets a clock and checks
a time.
TIMER : Uses your player as an
alarm clock.
• • • • • • d • • • • • •
RDS/SET :
- RDS (Radio Data System)
- Confirms the clock and the
alarm setting
DAB MODE :
- DAB radio type.
- Changes the display
information of DAB channel.
PTY : Searches radio stations by
radio type.
SORT/SCAN :
- Searches radio stations by radio
type.
- Aligns the service names DAB
band scanning.
2013-03-21
6:28:50
Getting Started
9
Front Panel
1
Getting Started
a1/!(Power)
Switches the unit ON or OFF.
bDisplay Window
c B(Insert/Eject)
Inserts or ejects a disc.
d T(Play/Pause)
- Starts and pauses playback.
- Selects STEREO/MONO.
FUNC.
Selects the function and input source.
e Y/U (Skip/Search)
- Searches backward or forward.
- Skips to the previous/next track/file.
yy Use top buttons after open the cover.
hPORT.IN
Listens to music from your portable device.
PHONES
Listens to music with your headphone.
(3.5 mm)
USB Port
Plays and records the audio files by
connecting the USB device.
EQ
Chooses sound impressions.
SET/DEMO/RDS
- Confirms the setting.
- Demonstrates each of functions.
- RDS (Radio Data System)
TIMER
Uses your player as an alarm clock.
CLOCK
Sets the clock and checks the time.
SLEEP
Sets the system to turn off automatically at
a specified time.
(Dimmer : The display window will be
darkened by half.)
VOL.+/Adjusts volume level.
f I(Stop)
- Stops playback or recording.
- Cancels DELETE function.
g Disc slot
Loads a disc.
CM2630-BR_DGBRLLK_ENG_6405.indd 9
2013-03-21
6:28:50
10
Getting Started
Rear Panel
1
Getting Started
aDAB ANT.
Connects the DAB antenna.
bANTENNA FM
Connects the FM wired antenna.
c SPEAKERS terminal (R/L)
d Cooling fan
e Power cord
>>Caution
Precautions in using the touch buttons
yy Use the touch buttons with clean and dry
hands.
- In a humid environment, wipe out any
moisture on the touch buttons before
using.
yy Do not press the touch buttons hard to
make it work.
- If you apply too much strength, it can
damage the sensor of the touch buttons.
yy Touch the button that you want to work in
order to operate the function correctly.
yy Be careful not to have any conductive
material such as metallic object on the
touch buttons. It can cause malfunctions.
CM2630-BR_DGBRLLK_ENG_6405.indd 10
2013-03-21
6:28:50
2Connecting
Connecting
Connecting to
speakers
11
Antenna Connection
Connect the FM Wire antenna to ANTENNA FM
connector.
Attaching the speakers to the
unit
To connect the cable to the unit, press each plastic
finger pad to open the connection terminals on the
unit. Insert the wire and release the finger pad.
2
Connecting
Connect the black wire to the terminals marked (minus) and the other end to the terminals marked
+ (plus).
,,Note
yy Be sure to fully extend the FM wire antenna.
>>Caution
The speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC
monitor screen. Please use the speakers far
away from either TV screen or PC monitor.
Color
Position
Red
Front right
White
Front left
CM2630-BR_DGBRLLK_ENG_6405.indd 11
yy When the broadcasting signal is weak
: Check the condition of broadcasting
reception. ( check the QUALITY)
yy When moving the unit to other areas
: Delete all of the saved DAB scanned
stations.
2013-03-21
6:28:51
12
Connecting
Optional Equipment
Connection
PORT. IN Connection
The unit can be used to play the music from many
types of external device. (Portable cable is not
supplied as an accessory with this unit.)
USB Connection
2
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the unit.
Connecting
,,Note
Removing the USB Device from the unit
1. Choose a different function/mode or
press ZENTER or I twice in a row.
2. Remove the USB device from the unit.
CM2630-BR_DGBRLLK_ENG_6405.indd 12
1. Connect the external device to the PORT. IN
connector of the unit.
2. Turn the power on by pressing 1 or 1/!.
3. Select the PORTABLE function by pressing
FUNCTION or FUNC.
4. Turn the external device on and start playing it.
2013-03-21
6:28:51
Connecting
13
PHONES Connection
Connect a pair of stereo headphones ( 3.5 mm
phone plug) to PHONES jack on the unit for private
listening.(Headphones are not supplied as an
accessory with this unit.)
2
Connecting
,,Note
You can’t hear any sound from speakers,
while the headphones plug is inserted in the
PHONES jack.
CM2630-BR_DGBRLLK_ENG_6405.indd 13
2013-03-21
6:28:51
14
Connecting
Basic Operations
CD/USB Operations
1. Insert a disc by pressing B or connect the USB
device to the USB port.
2
2. Select the CD or USB function by pressing
FUNCTION on the remote control or FUNC. on
the unit.
Connecting
3. Select a track/file you want to play by pressing
C/V on the remote control or Y/U
on the unit.
To
Stop
Playback
Pause
Skipping to
the next/
previous
track/ file
Searching
for a section
within a track/
file
Searching
for a section
within a folder
Selecting a folder and an
MP3/WMA
1. PRESET.FOLDER W/S on the remote control
repeatedly until a desired folder appears.
2. Press d/M to play it. The first file of folder will
be played. (During playback, if you selecting a
folder you want, this step is not necessary.)
,,Note
yy USB Folders/Files are recognized as below
ROOT
FOLDER
FOLDER 1
Do this
Press ZENTER or I.
Press d/M or T.
During playback, Press d/M or
T.
During playback, press V or U
to go to the next track/file.
Playing less than 2 seconds, press
C or Y to go to the previous
track/file.
FOLDER3
Press PRESET.FOLDER W/S on
the remote control.
Press REPEAT(MENU) on the
remote control repeatedly, the
Playing
display window will be changed in
repeatedly or
the following order,
randomly
RPT1 -> RPT DIR (only MP3/ WMA)
-> RPT ALL -> RANDOM -> OFF
FILE 5
FILE 6
FILE 7
FOLDER4
FOLDER7
FILE 8
FOLDER8
FILE 10
FILE 9
FILE 3
FILE 4
FOLDER 2
Playing after 3 seconds, press C
or Y to go to the beginning of
the track/file.
Press and hold C/V or Y/
U during playback and release it
at the point you want to listen to.
FILE
FOLDER5
FILE 11
FILE 12
FOLDER6
FILE 13
FILE 14
FILE 1
FILE 2
yy If there is no file in a folder, the folder will
not appear
yy Folders will be presented as the following
order;
ROOT FOLDER1 FOLDER3 FOLDER7
FOLDER8 FOLDER5 FOLDER6
yy File will be played from $ file No.1 to $ file
No.14 one by on.
yy Files and folders will be presented in order
recorded and may be presented differently
according to the record circumstances.
yy *ROOT : the first screen you can see when a
computer recognize the USB is “ROOT”.
yy The DTS is not supported. In case of DTS
audio format, audio is not output.
CM2630-BR_DGBRLLK_ENG_6405.indd 14
2013-03-21
6:28:52
Operating
Other Operation
15
Deleting an MP3/WMA file
Programmed Playback
You can delete file, folder or format by pressing
DELETE on the remote control. This function is
supported only in stop state. (USB only)
The program function enables you to store your
favourite tracks/files from any disc or USB device.
1. -Select the file you want to delete by using
C/V or Y/U . And press DELETE.
A program can contain 20 tracks/files.
-Select the folder you want to delete by
pressing PRESET.FOLDER W/S on the remote
control. Then press DELETE.
1. Insert a CD or connect USB and wait for it to be
loaded.
2.Press PROGRAM/MEMORY on the remote
control in stop state.
-Press and hold DELETE to format the USB
device.
Or
Press DELETE repeatedly while searching a file.
4.Press PROGRAM/MEMORY again to save and
select a next track/file.
The display window will be changed in the
following order.
5.Press d/M or T to play the programmed
music tracks/files.
6. To clear your selection, press and hold
ZENTER or I.
,,Note
The programs are also cleared when the disc
or USB device is removed, the unit is powered
off or the function is switched to others.
- DEL FILE? : Deletes file
- DEL FOLDER : Deletes folder
- FORMAT? : Formats USB
3
Operating
3.Press C/V or Y/U to select a next
track/file.
2. To delete file/folder or format, press d/M or
T.
3. If you want to exit the current mode, press
ZENTER or I.
>>Caution
o not extract the USB device during
yy D
operation. (play, delete, etc.)
egular back up is recommended to
yy R
prevent data loss.
yy T he delete function may not be supported
according to the USB state. (lock, etc.)
CM2630-BR_DGBRLLK_ENG_6405.indd 15
2013-03-21
6:28:52
16
Operating
Displaying file information
While playing an MP3 file containing file
information, you can display the information by
pressing INFO on the remote control.
Turn off the sound temporarily
Press MUTE@ on the remote control to mute
your sound.
You can mute the sound in order, for example, to
answer the telephone. the mute symbol “ ” will
appear in the display window. To cancel mute
function, press MUTE@ again or adjust volume
level by pressing VOL+/-.
3
Operating
DEMO
Radio Operations
Listening to the radio
1.Press FUNCTION or FUNC. until FM/DAB
appears in the display window.
The last received station is tuned in.
2. [FM]
Auto tuning : Press and hold CH/TUNING-/+
on the remote control for about 2 seconds until
the frequency indication starts changing, then
release. Scanning stops when the unit tunes in
a station.
Manual tuning : Press CH/TUNING-/+
repeatedly.
[DAB]
Press CH/TUNING-/+ and press d/M or T
when scanning stop.
In power off state, press SET/DEMO/RDS on the
unit once. The unit will power on and display the
each of functions in the display window. To cancel
DEMO function, press SET/DEMO/RDS again.
3. Adjust the volume by pressing VOL+/-.
Auto Power Down
Improving poor FM reception
This unit will be off itself to save electronic
consumption in the case main unit is not
connected to external device and is not used for 25
minutes. So does this unit after 6 hours since Main
unit has been connected to other device using
analog input.
Press d/M or T. This will change the tuner from
stereo to mono. Then the reception will be better
than before.
CM2630-BR_DGBRLLK_ENG_6405.indd 16
2013-03-21
6:28:52
Operating
Presetting the Radio Stations
You can preset 50 stations for FM/DAB . Before
tuning, make sure to turn down the volume.
1.Press FUNCTION or FUNC. until FM/DAB
appears in the display window.
2. [FM]
Select the desired frequency by pressing CH/
TUNING-/+.
[DAB]
Press CH/TUNING-/+ on the remote control
and press d/M or T.
3.Press PROGRAM/MEMORY on the remote
control. A preset number will blink in the display
window.
5.Press PROGRAM/MEMORY. The station is
stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press
PRESET.FOLDER W/S.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMORY on the
remote control for two seconds. “ERASE ALL” will
blink on the display window.
Seeing information about a
Radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about the
radio station being listened to. Press RDS/SET on
the remote control repeatedly to cycle through the
various data types. :
PS (Programme Service Name)
The name of the channel will appear in
the display
PTY (Programme Type Recognition)
The programme type (e.g. Jazz or News)
will appear in the display.
RT (Radio Text)
A text message contains special
information from the broadcast station.
This text may scroll across the display.
CT (Time controlled by the channel)
This shows the time and date as
broadcast by the station.
3
Operating
4.Press PRESET.FOLDER W/S on the remote
control to select the preset number you want.
17
You can search the radio stations by programme
type by pressing RDS/SET. The display will show
the last PTY in use. Press PTY one or more times
to select your preferred programme type. Press
and hold CH/TUNING-/+. The tuner will search
automatically. When a station is found, the search
will stop.
2.Press PROGRAM/MEMORY to erase all saved
radio stations.
CM2630-BR_DGBRLLK_ENG_6405.indd 17
2013-03-21
6:28:52
18
Operating
Listening to the DAB
You can change the display information of the
currently broadcasting DAB channel. Press
DAB MODE on the remote control repeatedly, the
display changes in the following order;
SERVICE -> PTY NAME -> FREQ -> DLS -> QUALITY
-> ENSEMBLE
Select a display mode and then press
CH/TUNING-/+, the initials of the servicename are
displayed.
SERVICE
isplays the Name of the channel for
D
the current broadcast.
PTY NAME
Displays the Type of the channel for
the current broadcast.
3
Sound adjustment
Setting the sound mode
This system has a number of pre-set sound fields.
You can select a desired sound mode by using
SOUND EFFECT or EQ.
The displayed items for the Equalizer may be
different depending on sound sources and effects.
Operating
On Display
Description
NATURAL
You can enjoy comfortable and
natural sound.
AUTO EQ
Sets the sound equalizer on the
mode that is the most similar to
the genre which is included in
the MP3 ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock, pop,
jazz or classic concert.
FREQDisplays the frequency of the channel
for the current broadcast.
DLS
It displays the current Scroll of the
channel which is selected.
QUALITY
It displays the current strength of the
broadcast signal.
ENSEMBLE
Displays the Ensemble of the channel
for the current broadcast.
Aligning the service names
Press SORT/SCAN on the remote control to display
the sorting mode of DAB broadcastings. Then, press
the button once again to change the mode.
Default sort:The service names are aligned in a
scanning order.
Name sort:The service names are aligned in an
alphabetical order.
DAB scan
Press SORT/SCAN on the remote control for longer
than 3 seconds, all of the DAB bands are scanned.
Then press it again, scanning will be cancelled.
Deleting all of the saved DAB
scan stations
MP3 -- OPT
BASS BLAST
(BASS)
LOUDNESS
BYPASS
This function is optimized
for compressible MP3 file. It
improves the treble sound.
Reinforces the treble, bass and
surround sound effect.
Improves the bass and treble
sound.
You can enjoy the sound
without equalizer effect.
,,Note
Maybe you need to reset the sound mode,
after switching the input, sometimes even
after the sound track/file is changed.
Press and hold DAB MODE on the remote control
for 3 seconds. “DAB INIT” will be displayed. Press
DAB MODE to erase all the saved stations.
CM2630-BR_DGBRLLK_ENG_6405.indd 18
2013-03-21
6:28:52
Operating
19
Setting the Clock
Using your player as an alarm
clock
You have two ways to set the clock.
1. Turn the unit on.
yy Setting the clock by connecting the BT.App.
2. Press and hold TIMER on the remote conrol to
set the alarm function.
Set time you desired on Bluetooth device and
connect the Bluetooth device to your unit via BT
app. Then the clock setting in the display window
will be synchronized with the Bluetooth device
automatically.
yy Setting the clock by pressing the buttons.
1. Turn the unit on.
2. Press and hold CLOCK.
3. Choose time mode by pressing C/V.
4.Press RDS/SET or SET/DEMO/RDS to confirm
your selection.
5. Select the hours by pressing C/V.
4. “ON TIME” will blink. This is your desired time to
turns unit on. Press C/V to change the
hours and minutes and press RDS/SET or
SET/DEMO/RDS to save.
5. “OFF TIME” will blink. This is your desired time
to turn unit off. Press C/V to change the
hours and minutes and press RDS/SET or
SET/DEMO/RDS to save.
6. The volume setting will blink. Press C/V
to change the volume and press RDS/SET or
SET/DEMO/RDS to save.
6.Press RDS/SET or SET/DEMO/RDS.
7.Press TIMER to check the alarm information.
7. Select the minutes by pressing C/V.
8. If you want to reset the clock, press and hold
TIMER.Then repeat step 3-6.
8.Press RDS/SET or SET/DEMO/RDS.
9. If you want to reset the clock, press and hold
CLOCK.Then repeat steps 3-8.
3
Operating
- 12:00 (for an AM and PM display) or 0:00 (for a
24 hour display)
3. Alarm sound sources will blink. While each of
sound sources blink, select the one you want by
pressing RDS/SET or SET/DEMO/RDS.
,,Note
yy If you unplug the cord from an outlet, the
clock setting you set won’t be stored.
yy If you synchronize the unit with your BT
device for clock by using BT app, you can
set 12 - Hour Time (ex - PM 11 : 00) or 24 Hour Time (ex - 23 : 00).(Android O/S only)
yy If you set the clock, you can check the time
by pressing CLOCK although the unit is
turned off.
yy If you set the clock and alarm, you can
check setting informaiton by pressing
TIMER although the unit is turned off. Then
this function will work in everyday.
yy Alarm function only works when the unit is
turned off.
yy When the alarm rings, you can deactivate
the alarm by pressing 1/! or 1.
CM2630-BR_DGBRLLK_ENG_6405.indd 19
2013-03-21
6:28:52
20 Operating
Sleep Timer Setting
Press SLEEP repeatedly to select delay time
between 10 and 180 minutes. After delay time, the
unit will turn off. (You can see the following order,
180 -> 150 ->120 -> 90 -> 80 -> 70 -> 60 -> 50 ->
40 -> 30 -> 20 -> 10)
To cancel the sleep function, press SLEEP
repeatedly until the display window get bright.
,,Note
yy Press SLEEP. The remaining time appears in
the display window.
yy Sleep function will work after dimmer
function.
3
Advanced Operation
Recording on USB
1. Connect the USB device to the unit.
2. Select a function by pressing FUNCTION or
FUNC.
One track/file recording - You can record a track/
a file on USB while playing the file you want.
All tracks/files recording - You can record tracks/
files on USB in stop state.
Program list recording - After making program
list, you can record it on USB.
(Refer to the page 15)
Operating
Dimmer
3. Start the recording by pressing USB REC on the
remote control.
Press SLEEP once. The display window will
be darkened by half. To cancel it, press SLEEP
repeatedly until the display window get bright.
4. To stop recording, press ZENTER.
Pausing recording
During recording, press USB REC to pause
recording. Press it again to restart recording. (Only
Radio/ Portable function)
To select recording bit rate
and speed
1.Press USB REC for longer than 3 seconds.
2.Use C/V to select the bit rate.
3.Press USB REC again to select the recording
speed.
4.Press C/V to select a desired recording
speed. (CD Function Only)
X1 SPEED
- You can listen to music while recording it.
(Audio CD Only)
X2 SPEED
- You can just record the music file.
5.Press USB REC to finish the setting.
CM2630-BR_DGBRLLK_ENG_6405.indd 20
2013-03-21
6:28:52
Operating
21
,,Note
yy You can check the recording percentage
rate for the USB record on the display
window during the recording. (MP3/ WMA
CD Only)
yy During recording MP3/ WMA, there is no
sound.
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Except MP3/WMA files)
yy Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
yy If USB recording does not work, the
message like “NO USB”, “ERROR”, “FULL” or “NO
REC” is displayed on the display window.
3
Operating
yy Multi card reader device, External HDD,
mobile phone can not be used for USB
recording.
yy A file is recorded by about 512 Mbyte when
you record for a long term.
yy You may not store more than 999 files.
yy It’ll be stored as follows.
AUDIO CD
MP3/ WMA
The other
source*
* : FM, PORTABLE and the like.
DAB, BT are not suppoted.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
CM2630-BR_DGBRLLK_ENG_6405.indd 21
2013-03-21
6:28:52
22 Operating
Using a Bluetooth
wireless technology
About Bluetooth
Bluetooth® is wireless communication technology
for short range connection.
The available range is within 10 meters.
3
Operating
(The sound may be interrupted when the
connection is interfered by the other electronic
wave or you connect the bluetooth in the other
rooms.)
Connecting individual devices under
Bluetooth® wireless technology does not incur any
charges. A mobile phone with
Bluetooth® wireless technology can be operated
via the Cascade if the connection was made via
Bluetooth® wireless technology.
Available Devices : Mobile phone, MP3, Laptop,
PDA.
Bluetooth Profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
Listening to music of a
Bluetooth device
Before you start the pairing procedure, make
sure the Bluetooth feature is turned on in to your
Bluetooth device. Refer to your Bluetooth device’s
user guide. Once a pairing operation is performed,
it does not need to be performed again.
1. Select the Bluetooth function by using the
FUNCTION on the remote control or FUNC.
on the unit. “BT READY” appears in the display
window.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device
display depending on the type of Bluetooth
device.Your unit dispalys as “LG MICRO(XX:XX)”.
,,Note
XX:XX means the last four digits of BT address.
For example, if your unit has a BT address such
as 9C:02:98:4A:F7:08, you will see “LG MICRO
(F7:08)” on your Bluetooth device.
3. Enter the PIN code.
PIN code : 0000
4. When this unit is successfully paired with
your Bluetooth device, “BT CONN” and “BT
PAIR”appears in the display window.
,,Note
Depending on the Bluetooth device type,
some devices have a different pairing way.
5. Listening to music.
To play a music stored on your Bluetooth
device, refer to your Bluetooth device’s user
guide. According to your Bluetooth device’s
volume level, the volume level of Bluetooth will
be adjusted.
,,Note
yy Sound from the main set can be distorted
if you raise the volume of Bluetooth device
up to two-thirds or more.
yy When you use the Bluetooth function,
adjust the volume of a Bluetooth device to
a proper level to listen to.
CM2630-BR_DGBRLLK_ENG_6405.indd 22
2013-03-21
6:28:53
Operating 23
,,Note
yy After searching for this unit on your
Bluetooth device, connect the Bluetooth
device with this unit. Then play the file you
want.
yy The sound may be interrupted when
the connection interfered by the other
electronic wave.
yy You cannot control the Bluetooth device
with this unit.
yy Pairing is limited one Bluetooth device per
one unit and multi-pairing is not supported.
yy Although the distance between your
Bluetooth and the set is less than 10m, if
there are obstacles between both, your
Bluetooth device cannot be connected.
3
Operating
yy Depending on the type of the device,
you may not be able to use the Bluetooth
function.
yy You can enjoy wireless system using phone,
MP3, Notebook, etc..
yy When not connected the Bluetooth, “BT
READY” appears in the display window.
yy The Electrical malfunction due to devices
using same frequency such as Medical
equipment, Microwaves or wireless
LAN devices, the connection will be
disconnected.
yy When someone stands and interrupts
communication between Bluetooth device
and the player, the connection will be
disconnected.
yy If the gotten away of the distance between
Bluetooth and the unit, the sound quality
is lower and lower. The connection will be
disconnected when the space between
the Bluetooth and the unit gets out of the
operating range of Bluetooth.
yy The device with Bluetooth wireless
technology is disconnected, if you turn off
the main unit or put the device away from
the main unit more than 10m.
yy If the Bluetooth device is disconnected, you
should connect the Bluetooth device to
your unit.
CM2630-BR_DGBRLLK_ENG_6405.indd 23
2013-03-21
6:28:53
24 Operating
Using LG Bluetooth
Remote app
Install “ LG Bluetooth Remote app ”
by using QR code
About LG Bluetooth Remote app
2. Tap an icon for installation.
LG Bluetooth Remote app bring a suite of new
features to your unit. To enjoy more features, you
are recommended to download and install free “ LG
Bluetooth Remote”.
3
1. Install “ LG Bluetooth Remote app” by using QR
code. Use the scaning software to scan the QR
code.
3. Tap an icon for downloading.
Install “ LG Bluetooth Remote app”
through “ Apple App Store” or
“Google Android Market”
Operating
1. Tap the Apple App Store icon or Google
Android Market(Google Play Store) icon.
2. In the search bar, type in the “LG Bluetooth
Remote” and search it.
3. In the search result list, find and tap “LG
Bluetooth Remote” to start downloading
Bluetooth app.
4. Tap an icon for installation.
5. Tap an icon for downloading.
,,Note
yy Make sure that your powered Bluetooth
device is connected to the Internet.
yy Make sure that your powered Bluetooth
device is equipped with “ Apple App Store”
or “Google Android Market(Google Play
Store)”
,,Note
yy Make sure that your powered Bluetooth
device is connected to the Internet.
yy Make sure that your powered Bluetooth
device has a scanning software application.
If you don’t have one, download one from
“Google Android Market(Google Play Store)”
or “Apple App Store”
Activate Bluetooth with LG
Bluetooth Remote app
LG Bluetooth Remote app helps to connect your
powered Bluetooth device to the unit.
1.Tap LG Bluetooth Remote app icon on the
home screen to open LG Bluetooth Remote app
application, and go to the main menu.
2. Tap [Setting] and select the unit you want.
3. If you want to get more information to operate,
tap [Setting] and [Help].
CM2630-BR_DGBRLLK_ENG_6405.indd 24
2013-03-21
6:28:53
Operating 25
,,Note
yy BT app will be available in the software version
as follow;
Android O/S : 2.3.3(or late)
iOS O/S : 4.3(or late)
yy While using Bluetooth, you may not operate
BT app. Disconnect Bluetooth device you have
connected before to use BT app properly.
yy If you use BT app for operation, there would
be some differences between BT app and the
supplied remote control. Use the supplied
remote control as necessary.
yy If you operate BT app with Bluetooth device
connected, the Blutooth connection you
have connected before may be disconnected.
(Depending on the smartpone’s O/S, this
process has a difference.)
3
Operating
yy Depending on the Bluetooth device, BT.app
may not work.
yy In Bluetooth function, if you use BT app, the
supplied remote control may not work.
yy When using BT app for remote control, the
operation may differ from the supplied
remote control.
yy According to the smartphone’s operating
system, you have some differences for BT app’s
operation.
yy When your Bluetooth device have been
already connected with other unit, disconnect
the Bluetooth connection first. Then you can
control your player through BT app.
yy The connection you’ve made may be
disconnected if you select other application or
change the setting of the connected device
via BT app.In such case, please check the
connection status.
yy After connection of BT app, music may be
output from your device. In this case, try
connecting procedure again.
CM2630-BR_DGBRLLK_ENG_6405.indd 25
2013-03-21
6:28:53
4Troubleshooting
26 Troubleshooting
Troubleshooting
Problem
No Power.
No sound.
Correction
yy Plug in the power cord.
yy Check the condition by operating other electronic devices.
Press FUNCTION or FUNC. and check the selected function.
yy Insert a playable disc.
The unit does not start
playback.
4
yy Clean the disc. (Refer to the 29 page)
yy Insert the disc with the label or printed side facing upward.
Troubleshooting
yy Connect the antenna securely.
Radio stations cannot be yy Tune to the station manually.
tuned in properly.
yy Preset some radio stations, see page 17 for details.
yy Operate the remote control within about 23 ft (7 m).
The remote control does yy Remove the obstacle in the path of the remote control and the unit.
not work properly.
yy Replace the batteries with new ones.
Clock is not displayed.
Connect your Bluetooth device to your unit through BT app for time sync.
CM2630-BR_DGBRLLK_ENG_6405.indd 26
2013-03-21
6:28:53
5Appendix
Appendix 27
Trademarks and
Licenses
The ‘DAB Digital Radio‘ logo and the stylised ‘r‘
mark® and © Digital One Ltd.”
Bluetooth® wireless technology is a system which
allows radio contact between electronic devices
within a max. range of 10 meters.
Connecting individual devices under Bluetooth®
wireless technology does not incur any charges.
A mobile phone with Bluetooth® wireless
technology can be operated via the Cascade if
the connection was made via Bluetooth® wireless
technology.
The Bluetooth® word mark and logos are owned
by the Bluetooth® SIG, Inc. and any use of such
marks by LG Electronics is under license.
5
CM2630-BR_DGBRLLK_ENG_6405.indd 27
Appendix
Other trademarks and trade names are those of
their respective owners.
2013-03-21
6:28:53
28 Appendix
Specifications
General
Power supply
Refer to the main label.
Power consumption
Refer to the main label.
Dimensions (W x H x D)
286 x 135 x 293 mm
Net Weight (Approx.)
3.8 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Bus Power Supply
DC 5 V 0 500 mA
Inputs
PORT. IN
0.5 Vrms (3.5 mm stereo jack)
Tuner
FM Tuning Range
87.5 MHz to 108.0 MHz or 87.50 MHz to 108.00 MHz
Amplifier
5
Stereo mode
80 W + 80 W
T.H.D
10 %
Appendix
CD
Frequency Response
30 to 20000 Hz
Signal-to-noise ratio
80 dB
Dynamic range
80 dB
Speakers
Type
3 Way 4 Speaker
Impedance
4Ω
Rated Input Power
80 W
Max. Input Power
160 W
Net Dimensions (WxHxD)
132 x 286 x 304 mm
Net Weight (1EA)
4 kg
yy Design and specifications are subject to change without notice.
CM2630-BR_DGBRLLK_ENG_6405.indd 28
2013-03-21
6:28:53
Appendix 29
Maintenance
Notes on Discs
Handling Discs
Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit.
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
5
Maintaining the Unit
CM2630-BR_DGBRLLK_ENG_6405.indd 29
2013-03-21
Appendix
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
6:28:53
30 Warranty
Technology with the human touch
GUARANTEE
• LG Electronics U.K. Ltd. will provide the following services in order toexpedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a
period of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be
reimbursed for any labour provided in the repair of this LG equipment, for a period of 12 months from
the original date of purchase. These claims must be made in accordance with the published scale of
service charges and relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made
to the apparatus, or if non standard components are used or if the serial number of the apparatus is
removed, defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a receipted
account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become
exhausted or worn in use.
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
This guarantee does not affect your statutory rights.
6
• REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE
SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED.
Warranty
• Product Registration Card :
It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This
will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should
modifications be necessary.
• To obtain information or assistance: C
all 0870 873 5454 Monday-Friday 9.00am-4.30pm
MODEL NO.*
SERIAL NO.*
DATE OF PURCHASE.*
In all cases of difficulty - consult your LG dealer from whom the product was purchased
LGEUK Website : www.lge.co.uk
( service website : www.lgelectronics.co.uk )
CM2630-BR_DGBRLLK_ENG_6405.indd 30
2013-03-21
6:28:54
CM2630-BR_DGBRLLK_ENG_6405.indd 31
2013-03-21
6:28:54
CM2630-BR_DGBRLLK_ENG_6405.indd 32
2013-03-21
6:28:54
Download PDF

advertising