LG | CM3430BDAB | LG CM3430WDAB Owner’s Manual

ENGLISH
OWNER’S MANUAL
Micro Hi-Fi System
Please read this manual carefully before operating
your set and retain it for future reference.
FOR THE GUARANTEE TERMS & CONDITIONS, PLEASE REFER TO
INNER PAGE OF BACK COVER.
CM3430BDAB
CM3430WDAB
CM3430GDAB
CM3330B-BK.DGBRLLK_ENG.indd 1
2013-02-18
8:32:20
1
Getting Started
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CM3330B-BK.DGBRLLK_ENG.indd 2
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not
try to open the enclosure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specification page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
2013-02-18
8:32:20
Getting Started
This device is equipped with a portable battery or
accumulator.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, shall be placed on the
apparatus.
Disposal of your old appliance
1.When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by
the European Directive 2002/96/EC.
2.All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or
the local authorities.
Disposal of waste batteries/accumulators
1. When this crossed-out wheeled
bin symbol is attached to batteries/
accumulators of Your product
it means they are covered by
European Directive 2006/66/EC.
2. This symbol may be combined with
chemical symbols for mercury(Hg),
cadmium(Cd) or lead(Pb) if the
battery Contains more that 0.0005%
of mercury,0.002% of cadmium or
0.004% of lead.
1
Getting Started
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, fire or the like.
3
3. All batteries/accumulators should
be disposed separately from
the municipal waste stream via
designated collection facilities
appointed by the government or
the local authorities.
4. The correct disposal of Your old
batteries/accumulators will help
to prevent potential negative
consequences for the environment,
animal and human health.
5. For more detailed information
about disposal of Your old batteries/
accumulators, please contact Your
city office, waste disposal service or
the shop where You purchased the
product.
3.The correct disposal of your
old appliance will help prevent
potential negative consequences
for the environment and human
health.
4.For more detailed information about
disposal of your old appliance,
please contact your city office,
waste disposal service or the shop
where you purchased the product.
CM3330B-BK.DGBRLLK_ENG.indd 3
2013-02-18
8:32:21
4
Getting Started
POWER: This unit operates on a mains supply
of 100-240V, 50/60Hz.
1
Getting Started
LG Electronics hereby declares that this/these
product(s) is/are in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC, 2004/108/EC, 2006/95/EC,
2009/125/EC and 2011/65/EU.
Please contact to the following address for
obtaining a copy of the DoC (Declaration of
Conformity).
Contact office for compliance of this product:
LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The Netherlands
yy Please note that this is NOT a Customer
Service contact point. For Customer Service
Information, see Warranty Card or contact the
dealer that you purchased this product.
In door use only.
RF Radiation Exposure Statement
This equipment should be installed and operated
with minimum distance 20cm between the
radiator and your body.
LG Bluetooth Remote
You can control this player with your iPhone or
Android phone via Bluetooth. This player and your
phone must be connected to Bluetooth. Visit
“ Apple App Store” or “Google Android Market
(Google Play Store)” . And use this QR code to
search for “LG Bluetooth Remote” app. For detailed
information, refer to the 26 page.
CM3330B-BK.DGBRLLK_ENG.indd 4
WIRING: This unit is supplied with a BSI 1363
approved 13 amp mains plug, fused at 5 amp.
When replacing the fuse always use a 5 amp
BS 1362, BSI or ASTA approved type. Never use
this plug with the fuse cover omitted. To obtain
a replacement fuse cover contact your dealer.
If the type of plug supplied is not suitable for
the mains sockets in your home, then the plug
should be removed and a suitable type fitted.
Please refer to the wiring instructions below:
WIRING: A mains plug removed from the
mains lead of this unit must be destroyed. A
mains plug with bared wires is hazardous if
inserted in a mains socket. Do not connect
either wire to the earth pin, marked with the
letter E or with the earth symbol or coloured
green or green and yellow. If any other plug is
fitted, use a 5 amp fuse, either in the plug, or at
the distribution board.
IMPORTANT: The wires in this mains lead are
coloured in accordance with the following
codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the
colours of the wires in the mains lead of this
unit may not correspond with the coloured
marking identifying the terminals in your plug,
proceed as follows: The wire which is coloured
blue must be connected to the terminal which
is marked with the letter N or coloured black.
The wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red.
2013-02-18
8:32:21
Table of Contents
Table of Contents
21
Getting Started
21
21
21
21
2
Safety Information
6
Unique Features
6Accessories
7
Playable file Requirement
8
Remote Control
10 Front Panel
10 Rear Panel
11 Connecting the AC adapter
22
23
23
23
23
24
25
1
2Operating
12
12
13
15
15
16
16
17
17
17
17
18
18
18
18
18
18
19
19
19
19
20
20
20
20
Basic Operations
– iPod/iPhone/iPad Operation
– Android device Operation
– USB Operation
– CD Operation
– Listening to music from your portable
device
– Listening to music with your
headphones
Other Operation
– Programmed Playback
– Selecting a folder and an MP3/WMA/
FLAC file.
– Resume playback
– Deleting an MP3/WMA/FLAC file
– Displaying file information
– Turn off the sound temporarily
– Sleep Timer Setting
– Dimmer
– Auto Power Down
Sound adjustment
– Setting the sound mode
Radio Operation
– Antenna Connection
– Listening to the radio
– Improving poor FM reception
– Presetting the Radio Stations
– Deleting all the saved stations
CM3330B-BK.DGBRLLK_ENG.indd 5
26
28
29
32
5
– Seeing information about a Radio
station
– Listening to the DAB
– Aligning the service names
– DAB scan
– Deleting all of the saved DAB scan
stations
Setting the Clock
– Using your player as an alarm clock
Advanced Operation
– Recording on USB
– To select recording bit rate and speed
Using a Bluetooth wireless technology
– Listening to music of a Bluetooth
device
Using LG Bluetooth Remote app
Using AirPlay
– Connecting your Wi-Fi device to Wi-Fi
network
– Streaming audio from your iTunes
music library to this unit
3Troubleshooting
1
2
3
4
5
34Troubleshooting
4Appendix
35 Trademarks and Licenses
36Specifications
37Maintenance
37 – Notes on Discs
37 – Handling the Unit
5Warranty
38Warranty
2013-02-18
8:32:21
6
Getting Started
Unique Features
1
USB Direct Recording
Accessories
Please check and identify the supplied accessories.
Getting Started
Records music to your USB device.
Portable In
Listens to music from your portable device. (MP3,
Notebook, etc)
Remote Control (1)
Battery (1)
AC adapter(1)
Power cord(1)
FM Antenna (1)
DAB antenna (1)
Timer
Sets alarm which go off at desired time.
Time Sync
Sets your unit’s clock automatically by using your
Bluetooth device. (LG Bluetooth Remote app)
Bluetooth®
Listens to music stored on your Bluetooth device.
AirPlay®
Listens to music stored on your Apple device.
CM3330B-BK.DGBRLLK_ENG.indd 6
2013-02-18
8:32:22
Getting Started
Playable file
Requirement
MP3/ WMA/FLAC file compatibility with this unit is
limited as follows :
yy S ampling frequency :
MP3 : within 8 to 48 kHz
WMA : within 8 to 48 kHz
FLAC : within 8 to 96 kHz(USB),
within 8 to 48 kHz(CD)
it rate : within 8 to 320 kbps (MP3),
yy B
40 to 192 kbps (WMA)
yy Maximum files : Under 999
yy File extensions : “.mp3”/ “.wma”/”.flac”
yy CD-ROM file format : ISO9660/ JOLIET
yy Support channel(FLAC) : Up to 2 channel
yy Support output bit/sample (FLAC) : 16bit
yy bps(FLAC) : Up to 2.5Mbps
yy You have to set the disc format option to
[Mastered] in order to make the discs compatible
with the LG players when formatting rewritable
discs. When setting the option to Live File System,
you cannot use it on LG players. (Mastered/ Live
File System : Disc format system for Windows
Vista)
CM3330B-BK.DGBRLLK_ENG.indd 7
Compatible USB Devices
yy MP3 Player : Flash type MP3 player.
SB Flash Drive :
yy U
Devices that support USB2.0 or USB1.1.
yy T he USB function of this unit does not support all
USB devices.
USB device requirement
evices which require additional program
yy D
installation when you have connected it to a
computer, are not supported.
1
Getting Started
MP3/ WMA/FLAC music file
requirement
7
yy Do not extract the USB device while in operation.
yy F or a large capacity USB, it may take longer than a
few minutes to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
sing NTFS file system is not supported. (Only
yy U
FAT(16/ 32) file system is supported.)
yy T his unit is not supported when the total number
of files is 1 000 or more.
yy E xternal HDD, Card readers, Locked devices, or
hard type USB devices, mobile phone are not
supported.
SB port of the unit cannot be connected to PC.
yy U
The unit cannot be used as a storage device.
yy Some USB may not work with this unit.
yy In power on state, you can charge your iPod/
iPhone/iPad/Android device via USB port. (This is
available when you selects USB function.)
2013-02-18
8:32:22
8
Getting Started
Remote Control
SLEEP : Sets the system to turn off automatically at
a specified time.
REPEAT(MENU) :
- Listens to your tracks/files repeatedly or randomly.
- Move to the previous menu when you select USB
function to play iPod/iPhone/iPad.
1
Getting Started
DELETE : Deletes MP3/WMA/FLAC files. (USB only)
Y/U (Skip/Search) :
- Skips Fast backward or Forward.
- Searches for a section within a track/file.
CH/TUNING-/+ :
- Selects a DAB display mode.
- Selects the radio stations.
IENTER :
- Stops playback or recording.
- Cancels DELETE function.
- Confirms the clock and the alarm setting.
• • • • • • • • • c • • • • • • • • • CLOCK : Sets a clock and checks a time.
T (Play/Pause) :
- Starts or pauses playback.
- Selects Stereo/Mono.
TIMER : Uses your player as an alarm clock.
• • • • • • • • • a • • • • • • • • • • 1 (Power) : Switches the unit ON or OFF.
(Insert/Eject) : Inserts or ejects a disc from a slot
loader.
VOL +/- : Adjusts speaker volume.
FUNCTION : Selects the function and input source.
PRESET/FOLDER W/S :
-- Searches for a folder of MP3/WMA/FLAC files.
When a CD/USB containing MP3/WMA/FLAC
files in several folders is being played, press
PRESET/FOLDER W/S to select the folder you
want to play.
RDS/SET :
- RDS(Radio Data System)
- Confirms the clock and the alarm setting.
(Refer to the 21 page)
DAB MODE :
- DAB radio type.
- Changes the display information of DAB channel.
USB REC : Starts recording
PTY : Searches radio stations by radio type.
SORT/SCAN :
- Searches radio stations by radio type.
- Aligns the service names DAB band scanning.
-- Chooses a preset number for a radio station.
@ MUTE : Mutes the sound.
• • • • • • • • • b • • • • • • • • • • PROGRAM/MEMORY :
- Stores radio stations.
- Creates a playlist you want to listen to.
SOUND EFFECT : Chooses sound impressions.
INFO : Sees information about your music.
CM3330B-BK.DGBRLLK_ENG.indd 8
2013-02-18
8:32:23
Getting Started
Battery Installation
You have two ways to open the battery
compartment.
9
3. Put the battery compartment on the remote
control and turn it clockwise to close.
1. Turn the battery compartment
counterclockwise by using a coin or your finger.
Then take a battery compartment out.
1
Getting Started
>>Caution
If you have long nails, do not open the battery
compartment by using your finger. Or else,
your nail would be broken.
>>Caution
The battery used in this device may present a
fire or chemical burn hazard if mistreated. Do
not recharge, disassemble, incinerate, or heat
above 100 °C (212 °F). Replace the battery part
no. CR2025 only. Use of another battery may
present a risk of fire or explosion. Dispose of
used battery. Keep battery away from children.
Do not disassemble or dispose of in fire.
2. Insert and fix the battery with the minus(-)
facing in the same direction as the minus(-).
+
+
CM3330B-BK.DGBRLLK_ENG.indd 9
2013-02-18
8:32:23
Getting Started
10
Front Panel
1
Getting Started
aSpeaker
b1/!(Power ON/OFF)
Switches the unit ON or OFF.
F(Function)
Selects the function and input source.
T(Play/Pause)
- Starts and pauses playback.
- Selects Stereo/Mono.
I(Stop)
Stops playback.
-/+ (Volume)
Adjusts volume level.
R (Insert/Eject)
Inserts or ejects a disc from a slot loader.
c Display Window
d Disc slot
Loads a disc.
Rear Panel
a
DAB ANT.
Connects the DAB antenna.
FM ANT.
Connects the FM wired antenna.
b (AirPlay)
Connects your unit to the existing Wi-Fi
network.
Air Direct/Reset
- Creates new Wi-Fi network with your unit.
- Initializes Wi-Fi network’s Security Mode.
CM3330B-BK.DGBRLLK_ENG.indd 10
c DC IN(AC adapter input)
d PORT.IN
Listens to music from your portable device.
PHONES
Listens to music with your headphone.
(3.5 mm)
eUSB Port
Plays and records the audio files by
connecting the USB device.
2013-02-18
8:32:24
Getting Started
>>Caution
Precautions in using the touch buttons
yy Do not press the touch buttons hard to
make it work.
- If you apply too much strength, it can
damage the sensor of the touch buttons.
Connecting the AC
adapter
1. Connect the supplied AC power cord to the AC
adapter.
2. Connect the AC adapter cable to DC IN adapter
input.
3. Plug the AC power cord into an AC outlet.
1
Getting Started
yy Use the touch buttons with clean and dry
hands.
- In a humid environment, wipe out any
moisture on the touch buttons before
using.
11
yy Touch the button that you want to work in
order to operate the function correctly.
yy Be careful not to have any conductive
material such as metallic object on the
touch buttons. It can cause malfunctions.
>>Caution
There are speakers at the bottom of your unit.
Be careful of this, when you handle it.
>>Caution
Only use the AC adapter supplied with this
device. Do not use a power supply from
another device or manufacturer. Using any
other power cable or power supply may cause
damage to the device and void your warranty.
CM3330B-BK.DGBRLLK_ENG.indd 11
2013-02-18
8:32:24
12
Operating
Basic Operations
To
iPod/iPhone/iPad Operation
You can enjoy the sound with your iPod/iPhone/
iPad. For details about iPod/iPhone/iPad, refer to
the iPod/iPhone/iPad User Guide.
2
1. Connect iPod/iPhone/iPad to the USB port by
using the iPod/iPhone/iPad’s cable.
Do this
Operating
ON UNIT
ON REMOTE
Pauses or
restart
T
T
Skip
-
Y/U
Search
-
Press and hold
Y/U
Move to the
previous
menu
-
REPEAT
(MENU)
Move to the
desired item
-
PRESET/
FOLDER
W/S
Chooses a
item
I
I ENTER
Compatible iPod/iPhone/iPad
If you turn this unit on, your iPod/iPhone/
iPad will be automatically turned on and start
recharging.
The unit supports the models as follows ;
iPad mini
iPad 4G
2.Press FUNCTION on the remote control or F on
the unit to select USB function. You can operate
your iPod/iPhone/iPad through an iPod/iPhone/
iPad’s display by using the remote control and
controlling your iPod/iPhone/iPad.
iPad 3G
iPad 2G
iPad
iPhone 5
iPhone 4S
iPhone 4
iPhone 3GS
iPod touch 5G
iPod touch 4G
iPod touch 3G
iPod nano 7G
iPod nano 6G
iPod nano 5G
iPod nano 4G
CM3330B-BK.DGBRLLK_ENG.indd 12
Depending on your iPod/iPhone/iPad’s software
version, you may not control your iPod/iPhone/
iPad from the unit.
Depending on your iPod/iPhone/iPad device,
you may not control your iPod/iPhone/iPad
from the unit.
2013-02-18
8:32:25
Operating
,,Note
yy If iPod/iPhone/iPad operation has an error,
check these problems as follows;
- Your iPod/iPhone/iPad is not connected firmly.
-This unit recognizes your iPod/iPhone/
iPad as an unknown device.
- Your iPod/iPhone/iPad is exceptionally low in power.
yy Depending on your iPod/iPhone/iPad ’s
software version, it may not be possible to
control your iPod/iPhone/iPad from this
unit. We recommed installing the latest
software version.
Android device Operation
You can enjoy the sound from your Android device
through USB port. For details about Android device,
refer to the Android device User Guide.
To stream audio from your Android device through
this unit, you need :
yy With Android operation system : Ver 4.1(or later)
and AOA 2.0 (or later)
2
yy With a micro USB cable
,,Note
You are recommended to remove the case
for your Android device(Ver 4.1or later) before
you connect your Android device to USB port
using a cable.
Operating
/ The battery needs to be charged.
/If you charge the battery while iPod/
iPhone/iPad is extremely low in power,
it may take longer to be charged.
13
1. Connect Android device to the USB port by
using the Android device’s cable.
yy If you use an application, make a call, or
send and receive SMS text message, etc. on
iPod touch or iPhone, disconnect it from
this unit and then use it.
yy If you have a problem with your iPod/
iPhone/iPad, please visit www.apple.com/
support.
yy You may need additional operation for iPod
touch/iPhone/iPad, for example “unlock”
before you use.
2.Press FUNCTION on the remote control or F on
the unit to select USB function.
3. If your unit is connected firmly, ‘ANDROID’ will
appear in the display window.
You can operate your Android device through
an Android device’s display by using the remote
control and controlling your Android device.
CM3330B-BK.DGBRLLK_ENG.indd 13
2013-02-18
8:32:25
14
Operating
To
Do this
Play
yy If the USB connection has an error, check
these problems as follows;
Press T.
Pause
During playback, pressT.
During playback, press Y/
U to go to the next file or to
return to the beginning of the
current file.
During playback, press Y
twice briefly to step back to the
previous file.
2
Operating
Skip
When you selects USB function, you can see
messages as follows;
Message
USB
Cause
Your device is not supported by
AOA 2.0 (Only charging)
Number of
This unit recognizes your USB.
files
IPOD
ANDROID
NO USB
This unit recognizes your iOS device
as an known device.
This unit recognizes your Android
device supported by AOA 2.0 as
known device.
Any device is not connected to USB
port.
This unit recognizes your Android
device as an unknown device.
,,Note
Depending on the type of device, Message will
appear in other way.
CM3330B-BK.DGBRLLK_ENG.indd 14
,,Note
-- Your Android device is not connected
firmly.
-- This unit recognizes your Android device as
an unknown device.
-- Your Android device is not booted.
yy The charging time may vary depending on
your Android device.
yy Some Android devices may not be charged.
yy You may not control your Android device
from this unit due to malfunction of Android
device.
yy Depending on your Android device’s
software version, it may not be possible
to control your Android device from this
unit. We recommend installing the latest
software version.
yy If you use an application, make a call, or
send and receive SMS text message, etc. on
Android device, disconnect it from this unit
and then use it.
yy Although your device’s O/S is ver 4.1 or
even the latest version, you can not charge
it. Because your device is not supported by
AOA 2.0.
yy Disconnect your device from USB port in
case of malfunction, although the device’s
O/S is ver 4.1(or later).
yy While the unit recognizes your android
device, you may see “USB CONNECT” in your
device.
yy If you connect your Android device to
USB port while your Android device is
extremely low in the volume, the audio may
not output from this unit. In this case, you
should adjust the volume of your Android
device.
2013-02-18
8:32:25
Operating
USB Operation
Connect the USB port of USB Memory (or MP3
player, etc.) to the USB port on the unit.
To
Stop
Playback
Pause
1. Choose a different function/mode or
press IENTER on the remote control
or I on the unit twice in a row.
2. Remove the USB device from the unit.
CD Operation
1. Insert a disc in the disc slot with the label side
upward.
2. Select the CD function by pressing FUNCTION
on the remote control or F on the unit.
3. Select a track/file you want to play by pressing
Y/U on the remote control.
Do this
Press IENTER on the remote
control or I on the unit.
Press T on the remote control.
During playback, Press T on the
remote control.
During playback, press U on the
remote control to go to the next
track/file.
Skipping to
Playing less than 2 seconds, press
the next/
Y on the remote control to go
previous
to the previous track/file.
track/ file
Playing after 3 seconds, press Y
on the remote control to go to the
beginning of the track/file.
Searching During playback, press and hold
for a section Y/U on the remote control
within a track/ and release it at the point you want
to listen to.
file
Searching
Press PRESET/FOLDER W/S on
for a section
the remote control.
within a folder
Press REPEAT(MENU) on the
remote control repeatedly, the
Playing
display window will be changed in
repeatedly or the following order,
randomly RPT1 -> RPT DIR (only MP3/ WMA/
FLAC) -> RPT ALL -> RANDOM ->
OFF
2
Operating
,,Note
Removing the USB Device from the unit
15
,,Note
yy Music CDs or CD-R/CD-RW in music CD
format can be only played.(12 cm disc)
yy The DTS is not supported. In case of DTS
audio format, audio is not output.
CM3330B-BK.DGBRLLK_ENG.indd 15
2013-02-18
8:32:25
16
Operating
Listening to music from your
portable device
Listening to music with your
headphones
The unit can be used to play the music from many
types of portable device. (Portable cable is not
supplied as an accessory with this unit.)
Connect a pair of stereo headphones ( 3.5 mm
phone plug) to PHONES jack on the unit for private
listening.(Headphones are not supplied as an
accessory with this unit.)
2
Operating
1. Connect the portable device to the PORT. IN
connector of the unit.
2. Turn the power on by pressing 1/!.
,,Note
You can’t hear any sound from speakers,
while the headphones plug is inserted in the
PHONES jack.
3. Select the PORTABLE function by pressing
FUNCTION on the remote control.
4. Turn the portable device on and start playing it.
CM3330B-BK.DGBRLLK_ENG.indd 16
2013-02-18
8:32:26
Operating
Other Operation
Programmed Playback
The program function enables you to store your
favourite tracks/files from any disc or USB device.
,,Note
yy USB/CD Folders/Files are recognized as
below
ROOT
FOLDER
FOLDER3
1. Insert a CD or connect USB and wait for it to be
loaded.
FILE 5
FILE 6
2
FILE 7
FOLDER4
3.Press Y/U on the remote control to select
a next track/file.
FOLDER7
FILE 8
FOLDER8
FILE 10
FILE 9
FILE 3
4.Press PROGRAM/MEMORY again to save and
select a next track/file.
FILE 4
FOLDER 2
FOLDER5
6. To clear your selection, press IENTER twice.
FILE 11
FILE 12
,,Note
FOLDER6
FILE 13
FILE 14
FILE 1
FILE 2
Selecting a folder and an
MP3/WMA/FLAC file.
yy If there is no file in a folder, the folder will
not appear
yy Folders will be presented as the following
order;
ROOT FOLDER1 FOLDER3 FOLDER7
FOLDER8 FOLDER5 FOLDER6
1. PRESET/FOLDER W/S on the remote control
repeatedly until a desired folder appears.
yy File will be played from $ file No.1 to $ file
No.14 one by one.
2. Press T to play it. The first file of folder will
play.
yy Files and folders will be presented in order
recorded and may be presented differently
according to the record circumstances.
Resume playback
yy *ROOT : The first screen you can see when a
computer recognize the USB/CD is “ROOT”.
During playback, if you change to another function,
then return to the USB/CD function, and then press,
you can listen to music from last point you played.
CM3330B-BK.DGBRLLK_ENG.indd 17
Operating
2.Press PROGRAM/MEMORY on the remote
control in stop state.
The programs are also cleared when the disc
or USB device is removed, the unit is powered
off or the function is switched to others.
FILE
FOLDER 1
A program can contain 20 tracks/files.
5.Press T to play the programmed music
tracks/files.
17
2013-02-18
8:32:26
18
Operating
Deleting an MP3/WMA/FLAC
file
You can delete file, folder or format by pressing
DELETE on the remote control. This function is
supported only in stop state. (USB only)
1. -Select the file you want to delete by using
Y/U . And press DELETE.
2
Operating
-Select the folder you want to delete by
pressing PRESET/FOLDER W/S. Then press
DELETE.
-Press and hold DELETE to format the USB
device.
Or
Press DELETE repeatedly while searching a file.
The display window will be changed in the
following order.
- DEL FILE : Deletes file
- DEL DIR? : Deletes folder
- FORMAT? : Formats USB
2. To delete file/folder or format, press T .
3. If you want to exit the current mode, press
I ENTER.
>>Caution
o not extract the USB device during
yy D
operation. (play, delete, etc.)
egular back up is recommended to
yy R
prevent data loss.
yy T he delete function may not be supported
according to the USB state. (lock, etc.)
Displaying file information
While playing an MP3/FLAC file containing file
information, you can display the information by
pressing INFO on the remote control.
Turn off the sound temporarily
Press @MUTE on the remote control to mute
your sound.
You can mute the sound in order, for example, to
answer the telephone. And “MUTE” will appear in
the display window. To cancel mute function, press
@MUTE again or adjust volume level by pressing
VOL+/-.
Sleep Timer Setting
Press SLEEP on the remote control repeatedly to
select delay time between 10 and 180 minutes.
After delay time, the unit will turn off. (You can see
the following order, 180 -> 150 ->120 -> 90 -> 80 ->
70 -> 60 -> 50 -> 40 -> 30 -> 20 -> 10)
To cancel the sleep function, press SLEEP
repeatedly until the display window get bright.
,,Note
yy Press SLEEP. The remaining time appears in
the display window.
yy Sleep function will work after dimmer
function.
Dimmer
Press SLEEP once. The display window will
be darkened by half. To cancel it, press SLEEP
repeatedly until the display window get bright.
Auto Power Down
This unit will be off itself to save electronic
consumption in the case main unit is not
connected to external device and is not used for 25
minutes. So does this unit after 6 hours since Main
unit has been connected to other device using
analog input.
CM3330B-BK.DGBRLLK_ENG.indd 18
2013-02-18
8:32:26
Operating
Sound adjustment
Radio Operation
Setting the sound mode
Antenna Connection
This system has a number of pre-set sound fields.
You can select a desired sound mode by using
SOUND EFFECT on the remote control.
The displayed items for the Equalizer may be
different depending on sound sources and effects.
Description
NATURAL
You can enjoy comfortable and
natural sound.
AUTO EQ
Sets the sound equalizer on the
mode that is the most similar to
the genre which is included in
the MP3 ID3 tag of song files.
POP
CLASSIC
JAZZ
ROCK
This program lends an
enthusiastic atmosphere to the
sound, giving you the feeling
you are at an actual rock, pop,
jazz or classic concert.
MP3 -- OPT
BASS
(BASS BLAST)
LOUDNESS
BYPASS
This function is optimized
for compressible MP3 file. It
improves the treble sound.
Connect the FM Wire antenna to FM ANT.
connector.
Connect the DAB antenna to the DAB ANT.
connector.
2
Operating
On Display
,,Note
yy Be sure to fully extend the FM wire antenna.
Reinforces the treble, bass and
surround sound effect.
yy When the broadcasting signal is weak
: Check the condition of broadcasting
reception. ( check the QUALITY)
Improves the bass and treble
sound.
yy When moving the unit to other areas
: Delete all of the saved DAB scanned
stations.
You can enjoy the sound
without equalizer effect.
19
,,Note
Maybe you need to reset the sound mode,
after switching the input, sometimes even
after the sound track/file is changed.
CM3330B-BK.DGBRLLK_ENG.indd 19
2013-02-18
8:32:26
20 Operating
2
Listening to the radio
Presetting the Radio Stations
1.Press FUNCTION on the remote control until
FM/DAB appears in the display window.
The last received station is tuned in.
You can preset 50 stations for FM/DAB . Before
tuning, make sure to turn down the volume.
2. [FM]
Auto tuning : Press and hold CH/TUNING-/+ for
about 2 seconds until the frequency indication
starts changing, then release. Scanning stops
when the unit tunes in a station.
Operating
Manual tuning : Press CH/TUNING-/+
repeatedly.
[DAB]
Press CH/TUNING-/+ and press T when
scanning stop.
3. Adjust the volume by pressing VOL+/-.
Improving poor FM reception
Press T on the remote control. This will change
the tuner from stereo to mono. Then the reception
will be better than before.
1.Press FUNCTION until FM/DAB appears in the
display window.
2. [FM]
Select the desired frequency by pressing CH/
TUNING-/+.
[DAB]
Press CH/TUNING-/+ and press T.
3.Press PROGRAM/MEMORY. A preset number
will blink in the display window.
4.Press PRESET/FOLDER W/S to select the
preset number you want.
5.Press PROGRAM/MEMORY. The station is
stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press
PRESET/FOLDER W/S.
Deleting all the saved stations
1. Press and hold PROGRAM/MEMORY for two
seconds. “ERASEALL” will blink on the display
window.
2.Press PROGRAM/MEMORY to erase all saved
radio stations.
CM3330B-BK.DGBRLLK_ENG.indd 20
2013-02-18
8:32:27
Operating
Seeing information about a
Radio station
The FM tuner is supplied with the RDS (Radio Data
System) facility. This shows information about the
radio station being listened to. Press RDS/SET
repeatedly to cycle through the various data types. :
You can search the radio stations by programme
type by pressing RDS/SET. The display will show
the last PTY in use. Press PTY one or more times
to select your preferred programme type. Press
and hold CH/TUNING-/+. The tuner will search
automatically. When a station is found, the search
will stop.
Listening to the DAB
You can change the display information of the
currently broadcasting DAB channel. Press
DAB MODE on the remote control repeatedly, the
display changes in the following order;
SERVICE -> PTY NAME -> FREQ -> DLS -> QUALITY
-> ENSEMBLE
Select a display mode and then press
CH/TUNING-/+, the initials of the servicename are
displayed.
SERVICE
isplays the Name of the channel for
D
the current broadcast.
PTY NAME
Displays the Type of the channel for
the current broadcast.
2
Operating
PS (Programme Service Name)
The name of the channel will appear in
the display
PTY (Programme Type Recognition)
The programme type (e.g. Jazz or News)
will appear in the display.
RT (Radio Text)
A text message contains special
information from the broadcast station.
This text may scroll across the display.
CT (Time controlled by the channel)
This shows the time and date as
broadcast by the station.
21
FREQDisplays the frequency of the channel
for the current broadcast.
DLS
It displays the current Scroll of the
channel which is selected.
QUALITY
It displays the current strength of the
broadcast signal.
ENSEMBLE
Displays the Ensemble of the channel
for the current broadcast.
Aligning the service names
Press SORT/SCAN on the remote control to display
the sorting mode of DAB broadcastings. Then, press
the button once again to change the mode.
Default sort:The service names are aligned in a
scanning order.
Name sort:The service names are aligned in an
alphabetical order.
DAB scan
Press SORT/SCAN on the remote control for longer
than 3 seconds, all of the DAB bands are scanned.
Then press it again, scanning will be cancelled.
Deleting all of the saved DAB
scan stations
Press and hold DAB MODE on the remote control
for 3 seconds. “DAB INIT” will be displayed. Press
DAB MODE to erase all the saved stations.
CM3330B-BK.DGBRLLK_ENG.indd 21
2013-02-18
8:32:27
22 Operating
Setting the Clock
Setting the clock by synchronizing
your iPod/ iPhone/iPad
You have three ways to set the clock.
Connect iPod/iPhone/iPad to the USB port using
the iPod/iPhone/iPad’s cable and select USB
function. Then the clock setting in the display
window will be synchronized with your iPod/
iPhone/iPad.
Setting the clock by pressing the
buttons
1. Turn the unit on.
2
2. Press and hold CLOCK.
Operating
3. Choose time mode by pressing Y/U.
- 12:00 (for an AM and PM display) or 0:00 (for a
24 hour display)
4.Press IENTER or RDS/SET to confirm your
selection.
5. Select the hours by pressing Y/U.
6.Press IENTER or RDS/SET.
7. Select the minutes by pressing Y/U.
8.Press IENTER or RDS/SET.
After the unit synchronized with your iPod/iPhone/
iPad for clock setting, there will be a time difference
between the iPod/iPhone/iPad and the unit . In
power off state, the clock won’t be synchronized
with your iPod/iPhone/iPad.
,,Note
Check the current time on iPod/iPhone/
iPad is correct or not. If not, reset it correctly
depending on present time. Wrong time on
the iPod/iPhone/iPad may result in the time
defference between your iPod/iPhone/iPad
and the unit.
9. If you want to reset the clock, press and hold
CLOCK.Then repeat steps 3-8.
Setting the clock by connecting the
BT.App
Set time you desired on Bluetooth device and
connect the Bluetooth device to your unit via BT
app. Then the clock setting in the display window
will be synchronized with the Bluetooth device
automatically.
CM3330B-BK.DGBRLLK_ENG.indd 22
2013-02-18
8:32:27
Operating 23
Using your player as an alarm
clock
1. Turn the unit on.
2. Press and hold TIMER to set the alarm function.
Advanced Operation
Recording on USB
3. Alarm sound sources will blink. While each of
sound sources blink, select the one you want by
pressing IENTER or RDS/SET.
1. Connect the USB device to the unit.
4. “ON TIME” will blink. This is your desired time to
turns unit on. Press Y/U to change the
hours and minutes and press IENTER or RDS/
SET to save.
6. The volume setting will blink. Press Y/U
to change the volume and press IENTER or
RDS/SET to save.
7.Press TIMER to check the alarm information.
8. If you want to reset the clock, press and hold
TIMER.Then repeat step 3-6.
,,Note
yy If you unplug the cord from an outlet, the
clock setting you set won’t be stored.
yy If you synchronize the unit with your BT
device for clock by using BT app, you can
set 12 - Hour Time (ex - PM 11 : 00) or 24 Hour Time (ex - 23 : 00).(Android O/S only)
yy If you set the clock, you can check the time
by pressing CLOCK although the player is
turned off.
yy If you set the clock and alarm, you can
check setting informaiton by pressing
TIMER although the unit is turned off. Then
this function will work in everyday.
yy Alarm function only works when the unit is
turned off.
yy When the alarm rings, you can deactivate
the alarm by pressing TIMER.
yy If the alarm rings with USB cable connected
to USB port, the function switches to tuner
function. (Depending on the type of device,
this may not be available.)
CM3330B-BK.DGBRLLK_ENG.indd 23
One track/file recording - You can record a track/
a file on USB while playing the file you want.
All tracks/files recording - You can record tracks/
files on USB in stop state.
Program list recording - After making program
list, you can record it on USB.
(Refer to the page 17)
2
Operating
5. The “OFF TIME” will blink. This is your desired
time to turn unit off. Press Y/U to change
the hours and minutes and press IENTER or
RDS/SET to save.
2. Select a function by pressing FUNCTION on the
remote control or F on the unit.
3. Start the recording by pressing USB REC on the
remote control.
4. To stop recording, press IENTER.
Pausing recording
During recording, press USB REC to pause
recording. Press it again to restart recording. (Only
FM/ Portable function)
To select recording bit rate
and speed
1.Press USB REC for longer than 3 seconds.
2.Use Y/U to select the bit rate.
3.Press USB REC again to select the recording
speed.
4.Press Y/U to select a desired recording
speed. (CD Function Only)
X1 SPEED
- You can listen to music while recording it.
(Audio CD Only)
X2 SPEED
- You can just record the music file.
5.Press USB REC to finish the setting.
2013-02-18
8:32:27
24 Operating
,,Note
yy You can check the recording percentage
rate for the USB record on the display
window during the recording. (AUDIO CD,
MP3/ WMA/ FLAC CD Only)
2
Using a Bluetooth
wireless technology
Operating
yy During recording MP3/ WMA/ FLAC, there is
no sound.
About Bluetooth
yy When you stop recording during playback,
the file that has been recorded at that time
will be stored. (Except for MP3/WMA/ FLAC
files)
The available range is within 10 meters.
yy Do not remove the USB device or turn
off the unit during USB recording. If not,
an incomplete file may be made and not
deleted on PC.
yy If USB recording does not work, the
message like “NO USB”, “ERROR(USB ERR)”,
“FULL(USB FULL)”, ”NO SUPPO”or “NO REC” is
displayed on the display window.
yy Multi card reader device, External HDD,
mobile phone can not be used for USB
recording.
yy A file is recorded by about 512 Mbyte when
you record for a long term.
yy You may not store more than 999 files.
yy It’ll be stored as follows.
AUDIO CD
MP3/ WMA/FLAC
The other
source*
Bluetooth® is wireless communication technology
for short range connection.
(The sound may be interrupted when the
connection is interfered by the other electronic
wave or you connect the bluetooth in the other
rooms.)
Connecting individual devices under
Bluetooth® wireless technology does not incur any
charges. A mobile phone with
Bluetooth® wireless technology can be operated
via the Cascade if the connection was made via
Bluetooth® wireless technology.
Available Devices : Mobile phone, MP3, Laptop,
PDA.
Bluetooth Profiles
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
* : FM, PORTABLE and the like.
DAB, BT, AirPlay are not suppoted.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
CM3330B-BK.DGBRLLK_ENG.indd 24
2013-02-18
8:32:27
Operating 25
Listening to music of a
Bluetooth device
Before you start the pairing procedure, make
sure the Bluetooth feature is turned on in to your
Bluetooth device. Refer to your Bluetooth device’s
user guide. Once a pairing operation is performed,
it does not need to be performed again.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device
display depending on the type of Bluetooth
device.Your unit dispalys as “LG MICRO(XX:XX)”.
,,Note
XX:XX means the last four digits of BT address.
For example, if your unit has a BT address such
as 9C:02:98:4A:F7:08, you will see “LG MICRO
(F7:08)” on your Bluetooth device.
yy After searching for this unit on your
Bluetooth device, pair the Bluetooth device
with this unit. Then play the file you want.
yy The sound may be interrupted when
the connection interfered by the other
electronic wave.
yy You cannot control the Bluetooth device
with this unit.
yy Pairing is limited one Bluetooth device per
one unit and multi-pairing is not supported.
yy Although the distance between your
Bluetooth and the set is less than 10m, if
there are obstacles between both, your
Bluetooth device cannot be connected.
yy Depending on the type of the device,
you may not be able to use the Bluetooth
function.
yy You can enjoy wireless system using phone,
MP3, Notebook, etc..
3. Enter the PIN code.
PIN code : 0000
yy When not connected the Bluetooth, “BT
READY” appears in the display window.
4. When this unit is successfully paired with
your Bluetooth device, “BT CONN” and “BT
PAIR”appears in the display window.
yy The Electrical malfunction due to devices
using same frequency such as Medical
equipment, Microwaves or wireless
LAN devices, the connection will be
disconnected.
,,Note
yy Depending on the Bluetooth device type,
some devices have a different pairing way.
yy Try pairing procedure if your device name is
not in the device list.
5. Listening to music.
To play a music stored on your Bluetooth
device, refer to your Bluetooth device’s user
guide. According to your Bluetooth device’s
volume level, the volume level of Bluetooth will
be adjusted.
,,Note
yy Sound from the main set can be distorted
if you raise the volume of Bluetooth device
up to two-thirds or more.
yy When you use the Bluetooth function,
adjust the volume of a Bluetooth device to
a proper level to listen to.
CM3330B-BK.DGBRLLK_ENG.indd 25
2
Operating
1. Select the Bluetooth function by using the
FUNCTION on the remote control or F on the
unit. “BT READY” appears in the display window.
,,Note
yy After your device is connected to the unit
via Blutooth, the function switches to BT
automatically. (Except for AirPlay).
yy When someone stands and interrupts
communication between Bluetooth device
and the player, the connection will be
disconnected.
yy If the gotten away of the distance between
Bluetooth and the unit, the sound quality
is lower and lower. The connection will be
disconnected when the space between
the Bluetooth and the unit gets out of the
operating range of Bluetooth.
yy The device with Bluetooth wireless
technology is disconnected, if you turn off
the main unit or put the device away from
the main unit more than 10m.
yy If the Bluetooth device is disconnected, you
should connect the Bluetooth device to
your unit.
2013-02-18
8:32:27
26 Operating
2
Using LG Bluetooth
Remote app
Install “ LG Bluetooth Remote app ”
by using QR code
About LG Bluetooth Remote app
2. Tap an icon for installation.
Operating
LG Bluetooth Remote app bring a suite of new
features to your unit. To enjoy more features, you
are recommended to download and install free “ LG
Bluetooth Remote”.
1. Install “ LG Bluetooth Remote app” by using QR
code. Use the scaning software to scan the QR
code.
3. Tap an icon for downloading.
Install “ LG Bluetooth Remote app”
through “ Apple App Store” or
“Google Android Market”
1. Tap the Apple App Store icon or Google
Android Market(Google Play Store) icon.
2. In the search bar, type in the “LG Bluetooth
Remote” and search it.
3. In the search result list, find and tap “LG
Bluetooth Remote” to start downloading
Bluetooth app.
4. Tap an icon for installation.
5. Tap an icon for downloading.
,,Note
yy Make sure that your powered Bluetooth
device is connected to the Internet.
yy Make sure that your powered Bluetooth
device is equipped with “ Apple App Store”
or “Google Android Market(Google Play
Store)”
yy If you want to get more information, refer to
explanation of BT app in “Apple App Store”
or “Google Android Market(Google Play
Store)”
,,Note
yy Make sure that your powered Bluetooth
device is connected to the Internet.
yy Make sure that your powered Bluetooth
device has a scanning software application.
If you don’t have one, download one from
“Apple App Store” or “Google Android
Market(Google Play Store)”.
Activate Bluetooth with LG
Bluetooth Remote app
LG Bluetooth Remote app helps to connect your
powered Bluetooth device to the unit.
1.Tap LG Bluetooth Remote app icon on the
home screen to open LG Bluetooth Remote app
application, and go to the main menu.
2. Tap [Setting] and select the unit you want.
3. If you want to get more information to operate,
tap [Setting] and [Help].
CM3330B-BK.DGBRLLK_ENG.indd 26
2013-02-18
8:32:28
Operating 27
,,Note
yy BT app will be available in the software
version as follow;
Android O/S : Ver 2.3.3(or late)
iOS O/S : Ver 4.3(or late)
yy While using Bluetooth, you may not activate
BT app. Disconnect Bluetooth device you
have connected before to use BT app
properly.
2
Operating
yy If you use Bluetooth app for operation,
there would be some differences between
Bluetooth app and the supplied remote
control. Use the supplied remote control as
necessary.
yy If you operate BT app with Bluetooth
device connected, the Blutooth
connection you have connected before
may be disconnected. (Depending on
the smartphone’s O/S, this process has a
difference.)
yy Depending on the Bluetooth device, BT.app
may not work.
yy In Bluetooth function, if you use BT app, the
supplied remote control may not work.
yy When using BT app for remote control, the
operation may differ from the supplied
remote control.
yy According to the smartphone’s operating
system, you have some differences for BT
app’s operation.
yy When your Bluetooth device have been
already connected with other unit, disconnect
the Bluetooth connection first. Then you can
control your unit through BT app.
yy The connection you’ve made may be
disconnected if you select other application
or change the setting of the connected
device via BT app. In such case, please check
the connection status.
yy To prevent a malfunction, you are
recommended to connect only one device
to this unit.
yy Don’t connect your smart device by using
a cable to USB port. Or else the Blutooth
connection will be disconnected.
yy After connection of BT app, music may be
output from your device. In this case, try
connecting procedure again.
CM3330B-BK.DGBRLLK_ENG.indd 27
2013-02-18
8:32:28
28 Operating
Using AirPlay
Apple AirPlay technology enables you to play your iTunes music library, hosted on a Mac, PC, iPhone, iPod
touch, or iPad on any AirPlay-enabled device connected to the Wi-Fi network.
To stream audio wirelessly by AirPlay, you need :
Wi-Fi Sharing
2
Compatible Apple
Device
Air Direct
iPad mini, iPad4, iPad3, iPad2, iPad, iPhone5, iPhone 4S, iPhone 4, iPhone 3GS,
iPod touch 5G, iPod touch 4G, iPod touch 3G
Operating
iOS Version
Ver.4.3.3(or later)
iTune Version
Ver.10.2.2(or later)
Wireless LAN
(internal antenna)
802.11 b/g
WPA(TKIP/AES)
Security Mode
Webpage address
Webpage
WPA2(TKIP/AES)
WEP with
Open mode
-
WPA(TKIP/AES)
WEP with
Open / Shared mode
WPA2(TKIP/AES)
192.168.1.1
(Optional for security))
192.168.1.111
WEP with
Open mode
yy This unit should be connected to the same local network as your iTunes host device through the
Wi-Fi router.
yy Depending on the kind and operating system or the application’s version and the setting status of AirPlayenabled device connected to this unit, AirPlay may not be operated normally.
yy Depending on the type of Network environment and your device state, it may take long time to connect
the unit.
yy WPA supports TKIP and WPA2 supports AES first.
CM3330B-BK.DGBRLLK_ENG.indd 28
2013-02-18
8:32:28
Operating 29
Connecting your Wi-Fi device
to Wi-Fi network
Option 1 : Using Wi-Fi Sharing
,,Note
Make sure that you set security mode to WPATKIP or WPA2-AES to connect the network
more quickly.
2.Press FUNCTION on the remote control or F on
the unit to select AIRPLAY function.
1.Press FUNCTION on the remote control or F on
the unit to select AIRPLAY function.
2.Press Air Direct/Reset on the unit. Then
“DIRECT” message appears and
icon blinks.
-- When the unit is changed to Air Direct Mode,
icon stops blinking.
2
3. In the network list, find and select “AIR DIRECT
XXXXXX”.
Operating
1. Connect your iPod touch/iPhone/iPad to the
network.
Option 2 : Using Air Direct without
security
3. Connect your iPod touch/iPhone/iPad to the
network first, then connect it to the unit using
your cable. Please touch iPod touch/iPhone/
iPad before you use.
4.Press
on the unit. “SET WIFI” message will
appear and
icon will blink.
5. Tap “Allow” from popup window from iPod
touch/iPhone/iPad. Then network information
will be shared to the unit.
6. When the unit is connected to the network,
“CONN OK” message will appear and
stop
blinking.
7. Use AirPlay on your iPod touch/iPhone/iPad
after “AIRPLAY” appears in the display window.
CM3330B-BK.DGBRLLK_ENG.indd 29
4. Use Airplay after your iPod touch/iPhone/iPad
or PC/MAC is connected.
,,Note
yy If “LG AIR DIRECT XXXXXX” is not in the list,
try to scan the available Wi-Fi networks
again.
yy When your iPod touch/iPhone/iPad or
PC/MAC is connected to “LG AIR DIRECT
XXXXXX” , you can’t use internet.
2013-02-18
8:32:29
30 Operating
Using Air Direct with Security mode
2
5. Launch Apple Safari browser or Microsoft
Internet Explorer browser on your iPod touch/
iPhone/iPad or PC/MAC.
6 Type in “192.168.1.1” at the browser address bar
and confirm.
7. Set security mode and insert password.
- Hexadecimal (0-9, A-F) 10 or 26 digits.
- 5 or 13 ASCII characters.
8. Tap or click “OK”
,,Note
yy If you want to deactivate Air Direct function,
press Air Direct/Reset.
yy If you want to initializes Wi-Fi network’s Security
Mode, press and hold Air Direct/Reset.
yy In case you can’t “LG AIR DIRECT XXXXXX” in
the network list, try connecting procedure
using Air Direct with Security mode.
Operating
Option 3 : Using Webpage
The new Wi-Fi network created by this unit only
allows access of one Wi-Fi enabled device. To avoid
interference from any other Wi-Fi devices, you are
recommended to temporarily disable the Wi-Fi
function on your other Wi-Fi devices.
,,Note
9. In the network list, find and select “AIR DIRECT
XXXXXX” again.
• “LG AUDIO Setup XXXXXX” is the temporary
and assistant Wi-Fi network for connection
of this unit to your home Wi-Fi router.
• While your iPod touch/iPhone/iPad or your
Wi-Fi enabled PC/Mac is connecting to “LG
AUDIO Setup XXXXXX” network, you can not
be able to use the Internet on them.
1.Press FUNCTION on the remote control or F on
the unit to select AIRPLAY function.
2. Press and hold .
-- “STEP1” message appears and
the display window.
icon blinks in
3. After 20 seconds, select “Setting” -> “Wi-Fi” your
iPod touch/iPhone/iPad or PC/MAC.
4. In the network list, select “ LG AUDIO Setup
XXXXXX”.
-- “STEP2” message appears and
icon blinks.
10.If you want to get back to non-security mode,
select security type as None.
CM3330B-BK.DGBRLLK_ENG.indd 30
2013-02-18
8:32:30
Operating
,,Note
yy If “LG AUDIO Setup XXXXXX” is not in the list,
try to scan the available Wi-Fi networks again.
yy If you want to deactivate Webpage function,
press and hold
until “AIRPLAY” message
appears in the display window.
31
10.If this unit is connected to your selected home
Wi-Fi network successfully,
-- icon stops blinking and stays.
-- “CONN OK” message appears for a moment
and then “AIRPLAY” message appears in the
dispaly window.
5. Launch Apple Safari browser or Microsoft
Internet Explorer browser on your iPod touch/
iPhone/iPad or PC/MAC.
2
Operating
6. Type in “192.168.1.111” at the browser address
bar and confirm.
7. Select your network name (SSID) from “Wireless
Network”.
8. Enter the network key if required.
9. Tap or click “OK” to proceed with network
settings change.
-- Follow the on-screen instructions to change and
confirm the internal Wi-Fi settings of this unit.
-- Please wait about 30 seconds and more.
,,Note
If there’s any problem during network
connection, if this unit is failed to connect
to the Wi-Fi network, or if you enter the
icon blinks and “ERROR”
wrong password,
message appears for a moment. Then “AIRPLAY”
message appears in the display window. In
these cases, please try network connection.
11.If you have security on your access point, you
need to input the security code as necessary.
,,Note
yy If you use other characters than the english
alphabet or digits for the SSID name of your
access point or wireless router, it may be
displayed differently.
yy WEP security mode generally have 4 keys
available on an access point setting. If your
access point or wireless router use WEP
security, enter the security code of the key
“No.1” to connect on your home network.
yy An Access Point is a device that allows you
to connect to your home network wirelessly.
CM3330B-BK.DGBRLLK_ENG.indd 31
2013-02-18
8:32:30
32 Operating
Streaming audio from your
iTunes music library to this
unit
2. Tap on the AirPlay icon
.
,,Note
2
Operating
Make sure that your iTunes host device is
connected to the same Wi-Fi network as this
unit. Your iTunes device can be an iPod touch/
iPhone/iPad installed with iOS 4.3.3 (or later) or
a Wi-Fi enabled PC/Mac installed with iTunes
10.2.2 (or later).
Stream from your iPod touch/
iPhone/iPad
1. Launch the “Music” application on your iPod
touch/iPhone/iPad.
3. Select “LG AUDIO XXXXXX” (or user customized
name) from the AirPlay list.
CM3330B-BK.DGBRLLK_ENG.indd 32
2013-02-18
8:32:31
Operating 33
4. Select a media file and start play.
-- After a while, you will hear music from this
unit.
-- Depending on your connection environment
and network condition, audio output may be
delayed.
2
Operating
,,Note
If you fail to hear music after successful setup,
do one of the following on your iPod touch/
iPhone/iPad:
yy Disconnect and then re-connect to the
same Wi-Fi router again.
yy Close all applications running at the
background.
yy Power off and then power on your iPod
touch/iPhone/iPad again.
CM3330B-BK.DGBRLLK_ENG.indd 33
2013-02-18
8:32:31
3Troubleshooting
34 Troubleshooting
Troubleshooting
Problem
No Power.
No sound.
Correction
yy Plug in the power cord.
yy Check the condition by operating other electronic devices.
Press F and check the selected function.
yy Insert a playable disc.
3
The unit does not start
playback.
yy Clean the disc. (Refer to the 37 page)
yy Insert the disc with the label or printed side facing upward.
Troubleshooting
yy Connect the antenna securely.
Radio stations cannot be yy Tune to the station manually.
tuned in properly.
yy Preset some radio stations, see page 20
yy Operate the remote control within about 23 ft (7 m).
The remote control does yy Remove the obstacle in the path of the remote control and the unit.
not work properly.
yy Replace the battery with new one.
iPod/iPhone/iPad does
not work.
Connect your iPod/iPhone/iPad using USB cable firmly .
Android device does not yy Check whether your device’s O/S is ver 4.1(or later) or AOA 2.0(or later).
yy Connect your Android device using USB cable firmly.
work.
Clock does not
displayed.
CM3330B-BK.DGBRLLK_ENG.indd 34
yy Connect your Bluetooth device to your unit through BT app.
yy Connect your iPod/iPhone/iPad using USB cable firmly for time sync.
2013-02-18
8:32:31
4Appendix
Appendix 35
Trademarks and
Licenses
“Made for iPod,” “Made for iPhone,” and “Made for
iPad” mean that an electronic accessory has been
designed to connect specifically to iPod, iPhone,
or iPad, respectively, and has been certified
by the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPod, iPhone, or
iPad may affect wireless performance.
4
Appendix
The ‘DAB Digital Radio‘ logo and the stylised ‘r‘
mark® and © Digital One Ltd.”
Bluetooth® wireless technology is a system which
allows radio contact between electronic devices
within a max. range of 10 meters.
Connecting individual devices under Bluetooth®
wireless technology does not incur any charges.
A mobile phone with Bluetooth® wireless
technology can be operated via the Cascade if
the connection was made via Bluetooth® wireless
technology.
The Bluetooth® word mark and logos are owned
by the Bluetooth® SIG, Inc. and any use of such
marks by LG Electronics is under license.
Other trademarks and trade names are those of
their respective owners.
The Wi-Fi CERTIFIED Logo is a certification mark
of the Wi-Fi Alliance.
CM3330B-BK.DGBRLLK_ENG.indd 35
2013-02-18
8:32:32
36 Appendix
Specifications
General
AC adapter requirements
DC IN 18 V 0 2.67 A , 100 - 240 V ~ 50 - 60 Hz
Power consumption
Refer to the main label.
Dimensions (W x H x D)
520 x 87 x 180 mm
Net Weight (Approx.)
3.7 kg
Operating temperature
5 °C to 35 °C (41 °F to 95 °F)
Operating humidity
5 % to 90 %
Bus Power Supply
DC 5 V 0 2100 mA
Inputs
PORT. IN
0.5 Vrms (3.5 mm stereo jack)
Tuner
4
FM Tuning Range
87.5 MHz to 108.0 MHz or 87.50 MHz to 108.00 MHz
Appendix
Amplifier
Stereo mode
5 W + 5 W(Front), 30 W(Dual Woofer)
T.H.D
10 %
CD
Frequency Response
30 to 20000 Hz
Signal-to-noise ratio
80 dB
Dynamic range
80 dB
Sub Woofer
Type
Built-in
Impedance
8Ω
Rated Input Power
10 W
Max. Input Power
20 W
Front Speaker
Type
Built-in
Impedance
6Ω
Rated Input Power
5W
Max. Input Power
10 W
yy Design and specifications are subject to change without notice.
CM3330B-BK.DGBRLLK_ENG.indd 36
2013-02-18
8:32:32
Appendix 37
Maintenance
Notes on Discs
Handling Discs
Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
Do not use volatile liquids such as insecticide spray
near the unit.
Wiping with strong pressure may damage the
surface.
Do not leave rubber or plastic products in contact
with the unit for a long period of time.
Cleaning the unit
4
Appendix
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Maintaining the Unit
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
or worn, the picture quality could be diminished.
For details, please contact your nearest authorized
service center.
CM3330B-BK.DGBRLLK_ENG.indd 37
2013-02-18
8:32:32
38 Warranty
Technology with the human touch
GUARANTEE
• LG Electronics U.K. Ltd. will provide the following services in order toexpedite this Guarantee.
1. All faulty components which fail due to defective manufacture will be replaced free of charge for a
period of 12 months from the original date of purchase.
2. The dealer (or his service agent) who sold the product will be
reimbursed for any labour provided in the repair of this LG equipment, for a period of 12 months from
the original date of purchase. These claims must be made in accordance with the published scale of
service charges and relevant claims procedure.
PLEASE NOTE:
A. The dealer may restrict the guarantee to the original purchaser.
B. The dealer is not obliged to carry out service under guarantee if unauthorized modifications are made
to the apparatus, or if non standard components are used or if the serial number of the apparatus is
removed, defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the equipment was
originally purchased. The dealer may, before carrying out service under guarantee, require a receipted
account as evidence of the date of purchase.
D. We respectfully point out that your dealer is not obligated to replace batteries if they become
exhausted or worn in use.
5
E. Aerial alignment and consumer control adjustments are not covered by this guarantee.
Warranty
This guarantee does not affect your statutory rights.
• REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT MUST BE
SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED.
• Product Registration Card :
It is helpful to complete at least your name, address, phone, model & serial numbers and return it. This
will enable LG to assist you in the future should you lose your receipt, your units be stolen, or should
modifications be necessary.
• To obtain information or assistance: Call 0870 873 5454 Monday-Friday 9.00am-4.30pm
MODEL NO.*
SERIAL NO.*
DATE OF PURCHASE.*
In all cases of difficulty - consult your LG dealer from whom the product was purchased
LGEUK Website : www.lge.co.uk
( service website : www.lgelectronics.co.uk )
CM3330B-BK.DGBRLLK_ENG.indd 38
2013-02-18
8:32:32
CM3330B-BK.DGBRLLK_ENG.indd 39
2013-02-18
8:32:32
CM3330B-BK.DGBRLLK_ENG.indd 40
2013-02-18
8:32:32
Download PDF