LG | 20LS3R | LG 20LS3R Owner’s Manual

LCD TV
OWNER’S MANUAL
MODELS: 20LS3R
*
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer when you require service.
Contents
2
Installation
3
Location and function of controls
Remote control handset
Battery installation / Front/ Rear
5
Basic operation
On and off
On-Screen Menu Language/ Country Selection
9
On screen menus
Menu selection / Programme selection
Volume adjustment
10
Setting up TV stations
Auto programme tuning / Manual programme tuning
Programme edit / Favourite programme
Calling the programme table
11
Picture adjustment
PSM (Picture Status Memory)
Picture adjustment
CSM (Colour Status Memory)
XD function / Cinema / Reset
16
Sound adjustment
SSM (Sound Status Memory)
Sound adjustment / Stereo/ Dual reception
NICAM reception / Sound output selection
20
Time Menu
Clock / On/Off time
Auto sleep / Sleep timer
22
Other functions
Child lock / LED Lighting / XD Demo
TV, AV and PC modes / Auto AV switching
24
Teletext
Switch on/off
SIMPLE text / TOP text
FASTEXT / Special teletext functions
27
Connection of external equipment
Aerial socket / Euro scart socket (VCR)
DVD input sockets
DTV in sockets
29
Connection of PC
PC in socket
PC Setup
Selecting wide XGA mode
31
Picture format
External Control Device Setup ; RJ-12
Troubleshooting checklist
Product Specifications
34
35
40
42
ENGLISH
Installation
Warning
There is marking of ‘WARNING HIGH-VOLTAGE’ at the bottom of stand.
Connection of TV
* Caution: Please be sure to connect the TV to the AC power
adapter before connecting the TV's power plug to a wall power
outlet.
a. Connect the antenna cable to the antenna input port on the
TV.
b. Connect the AC adapter plug to the power input jack on the
TV.
c. Connect the power cord to the AC adapter first, then plug the
power cord into the wall power outlet.
d. Use only power supplies listed in the user instuction.
Note: Here shown may be somewhat different from your set.
Positioning your display
• Tilt range
Adjust the position of the panel in various ways for
maximum comfort.
15
0
Note: Do not put your hand (finger) between head
section and stand section when adjusting angle of
screen. Your hand (finger) may get caught or wounded.
Location
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken
not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set
is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back
cover.
If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to
the back of the TV.
When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
3
Installation
Kensington Security System
- The TV is equipped with a Kensington Security System
connector on the back panel. Connect the Kensington
Security System cable as shown below.
- For the detailed installation and use of the Kensington
Security System, refer to the user’s guide provided with
the Kensington Security System.
For further information, contact http://www.kensington.com,
the internet homepage of the Kensington company.
Kensington sells security systems for expensive electronic
equipment such as notebook PCs and LCD projectors.
Note:
- The Kensington Security System is an optional accessory.
Note:
a. If the TV feels cold to the touch, there may be a small “flicker” when when it is turned on.
This is normal, there is nothing wrong with TV.
b. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on the monitor's performance.
c. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
Desktop Pedestal Installation
For proper ventilation, allow a clearance of 4" on each side and
from the wall.
4
ENGLISH
Location and function of controls
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the top
panel of the set. Only the remote control handset supplied will
operate this set.
Remote control handset
Before you use the remote control handset, please install the
batteries. See the next page.
1. MUTE
switches the sound on or off.
Press the MUTE button. The sound is switched off and the display
appears.
You can cancel it by pressing the MUTE, F / G, I/II, or SSM button.
2. TV
returns to the TV mode.
switches the set on from standby.
10
MUTE
1
11
TV
12
13
3
4
PR
5
OK
VOL
D
7. SSM (Sound Status Memory)
recalls your preferred sound setting.
VOL
PR
Press the Q.VIEW button to view the last programme you were
watching.
6
6. NUMBER BUTTONS
switches the set on from standby and selects a programme.
I/II
LIST Q.VIEW MENU
4. Q.VIEW
returns to the previously viewed programme.
/ E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Down/Up)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the current mode.
INPUT
2
3. LIST
displays the programme table.
5.
POWER
7
8
1
2
3
4
5
6
7
8
9
SSM
0
PSM
SLEEP
ARC
14
TEXT
9
15
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
?
INDEX LIGHTING MODE
i
M
8. ARC
select your desired picture format.
9. SLEEP
sets the sleep timer.
10. INPUT
selects the remote operating mode.
switches the set on from standby.
5
Location and function of controls
11. POWER
switches the set on from standby or off to standby.
12. I/II
selects the language during dual language broadcast.
11
2
14
10
7
12
1
3
13. MENU
selects a menu.
14. PSM (Picture Status Memory)
recalls your preferred picture setting.
6
15. TELETEXT BUTTONS
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
4
COLOURED BUTTONS : These buttons are used for teletext (only
TELETEXT models) or programme edit.
* LIGHTING : Press the Lighting button to set LED Lighting
menu.
5
Battery installation
9
8
13
15
LIGHTING
The remote control handset is powered by two AAA batteries. To load
the batteries, turn the remote control handset over and open the battery compartment. Install two batteries as indicated by the polarity
symbols ( + and - ) marked inside
the compartment.
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
6
ENGLISH
Location and function of controls
Front
If your product has a protection film attached, remove the film and then wipe the product with a polishing
cloth.
20LS3R*
Side panel
PR
6
VOL
5
OK
18
4
MENU
3
INPUT
2
7
D
/ E (Programme Down/Up)
selects a programme or a menu item.
switches the set on from standby.
1. ON/OFF (r / I)
switches the set on from standby or off to
standby.
6.
2. INPUT
selects the remote operating mode.
switches the set on from standby.
7. REMOTE CONTROL SENSOR
3. MENU
selects a menu.
8. POWER/STANDBY INDICATOR
illuminates orange in standby mode.
illuminates red when the set is switched on.
4. OK
accepts your selection or displays the current
mode.
5.
F
/ G (Volume Down/Up)
adjusts the volume.
adjusts menu settings.
7
Location and function of controls
Rear
20LS3R*
HDMI
DVI IN
AV
HDMI DVI
EURO SCART
INPUT
SOCKET
RJ12
AUDIO IN
D-SUB
RGB/DVI
COMPONENT
PC/DVI
COMPONENT
PC SOUND
INPUT
RJ12 PORT
PC INPUT
JACK
8
ANTENNA
IN
DC-IN
DC 16V INPUT
(Use with AC adapter)
ANTENNA
INPUT
ENGLISH
Basic operation
On and off
1. Press the POWER, D / E, TV, INPUT or NUMBER buttons to
switch it on fully.
2. Press the POWER button. The set reverts to standby mode.
3. Pull out mains plugs to switch the set off.
POWER
TV
INPUT
Note : If, while the set is switched on, the mains plug is disconnected
the set will switch to standby or power on when the mains plug is
replaced in the mains power socket.
MENU
On-Screen Menu Language / Country Selection
Installation guide menu appears on TV screen when it is turned on for the
first time.
I/II
PR
OK
VOL
VOL
PR
1. Press the D / E / F / G button and then, OK button to select your
desired language.
2. Press the D / E / F / G button and then, OK button to select your
country.
1
2
3
4
5
6
7
8
9
SSM
0
* If you want to change Language/ Country selection
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Language.
The menus can be shown on the screen in the selected language.
Or, Press the G button and then D / E button to select Country.
3. Press the G button and then D / E / F / G button to select your
desired language or country.
4. Press the OK button.
5. Repeatedly press the MENU button to return to normal TV
viewing.
Note:
a. If you don’t finish set up Installation Guide by pressing MENU
button or time out of OSD (On Screen Display) display, it will
continuously appear until completing set up whenever the set
is turned on.
b. If you select wrong local country, the teletext may not appear
correctly on the screen and some problem may happen during
teletext operation.
c. Hebrew is added to Country of Installation Guide according
to the countries which using Hebrew languages.
9
On screen menus
Menu selection
MENU
PR
OK
VOL
VOL
PR
1. Press the MENU button and then D / E button to display each menu.
2. Press the G button and then D / E button to select a menu item.
3. Change the setting of an item in the sub or pull-down menu with
F / G button.
You can move to the higher level menu by pressing the OK
button and to move to the lower level menu by pressing the
MENU button.
Note :
a. In the teletext mode, menus are not displayed.
b. On some models, the Language will not be displayed.
Programme selection
You can select a programme number with the
buttons.
D
/
E
or NUMBER
Volume adjustment
Press the
/
G
button to adjust the volume.
Station
Picture
Sound
Auto programme
Manual programme
Programme edit
Favourite programme
PSM
CSM
XD
Cinema
Reset
SSM
AVL
Balance
DE
FG
OK MENU
STATION menu
DE
FG
OK MENU
PICTURE menu
DE
FG
0
OK MENU
SOUND menu
Screen
Special
Time
Auto config.
Manual config.
XGA Mode
Language
Country
Child lock
Lighting
XD Demo
Clock
Off time
On time
Auto sleep
ARC
Reset
DE
FG
OK MENU
SCREEN menu
10
F
DE
FG
OK MENU
SPECIAL menu
DE
FG
OK MENU
TIME menu
ENGLISH
Setting up TV stations
Up to 100 TV stations can be stored by programme numbers (0 to 99).
Once you have preset the stations, you will be able to use the D / E
or NUMBER buttons to scan the stations you have programmed.
Stations can be tuned using automatic or manual modes.
Station
Auto programme
Manual programme
Programme edit
Favourite programme
Auto programme tuning
All stations that can be received are stored by this method. It is
recommended that you use auto programme during installation
of this set.
DE
FG
MENU
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Auto
programme.
PR
Auto programme
System
Storage from
Search
G
BG
OK
I
VOL
FG
VOL
DK
PR
L
DE
OK MENU
OK MENU
3. Press the G button. Select a TV system with the G button and
then D / E button on the System menu;
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
L
: SECAM L/L’ (France)
4. Press the OK button.
1
2
3
4
5
6
7
8
9
0
5. Press the D / E button to select Storage from.
6. Select the beginning programme number with the F / G button
or NUMBER buttons on the Storage from pull-down menu. Any
number under 10 is entered with a numeric ‘0’ in front of it, i.e.
‘05’ for 5.
7. Press the OK button.
8. Press the
D
/
E
button to select Search.
Auto programme
System
Storage from
Search
Auto programme
G
To start
C 05
5
MENU
DE
FG
BG
35%
Stop
OK MENU
9. Press the G button to begin auto programming.
All receivable stations are stored.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the ‘Programme edit’ section
to edit the stored programme.
10. Repeatedly press the MENU button to return to normal TV
viewing.
11
Setting up TV stations
Manual programme tuning
Station
Auto programme
Manual programme
Programme edit
Favourite programme
DE
FG
Manual programme lets you manually tune and arrange the
stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
OK MENU
MENU
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Manual
programme.
3. Press the G button and then D / E button to select Storage.
Manual programme
Storage
System
Band
Channel
Fine
Search
Name
PR
OK
VOL
VOL
PR
DE
1
2
3
4
5
6
7
8
9
29
G
FG
OK MENU
4. Select the desired programme number (0 to 99) with the F / G
button or NUMBER buttons on the Storage menu. Any number
under 10 is entered with a numeric ‘0’ in front of it, i.e. ‘05’ for 5.
5. Press the OK button.
0
6. Press the D / E button to select System.
7. Select a TV system with the G button and then F / G button on
the System menu;
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
L
: SECAM L/L’ (France)
8. Press the OK button.
9. Press the D / E button to select Band.
10. Press the G button and then D / E button to select VHF/UHF or
Cable on the Band menu.
11. Press the OK button.
12. Press the D / E button to select Channel.
13. Select the desired programme with F / G button or NUMBER
buttons.
14. Press the OK button.
15. Press the D / E button to select Search.
16. Press the G button and then F / G button to commence searching on the Search pull-down menu. If a station is found the search
will stop.
17. Press the OK button to store it.
18. To store another station, repeat steps 3 to 17.
Manual programme
Storage
System
Band
Channel
Fine
Search
Name
DE
FG
G
F
/G
OK MENU
19. Repeatedly press the MENU button to return to normal TV
viewing.
12
ENGLISH
Setting up TV stations
Assigning a station name
1. Repeat the ‘Manual programme tuning’ steps 1 to 2.
2. Press the G button and then D / E button to select Name.
3. Press the G button and then use the D / E. You can use a blank,
+, -, the number 0 to 9 and the alphabet A to Z. It can be saved 5
digits for name.
With the F button you can select in the opposite direction.
4. Select the position by pressing the F / G button and then make
your choice of the second character, and so on.
5. Press the OK button to store it.
6. Repeatedly press the MENU button to return to normal TV
Station
Auto programme
Manual programme
Programme edit
Favourite programme
DE
FG
OK MENU
viewing.
Fine tuning
MENU
Normally fine tuning is only necessary if reception is poor.
1. Repeat the ‘Manual programme tuning’ steps 1 to 2.
2. Press the G button and then D / E button to select Fine.
3. Press the G button
4. Press the F / G button to fine tune for the best picture and sound
on the Fine pull-down menu.
5. Press the OK button.
6. Repeatedly press the MENU button to return to normal TV
viewing.
The finely tuned programme will be indicated by orange number during programme selection.
PR
OK
VOL
VOL
PR
Manual programme
Storage
System
Band
Channel
Fine
Search
Name
DE
FG
G
F
/G
OK MENU
13
Setting up TV stations
Programme edit
Station
Auto programme
Manual programme
Programme edit
Favourite programme
DE
FG
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
OK MENU
MENU
1. Press the MENU button and then D / E button to select the
STATION menu.
2. Press the G button and then D / E button to select Programme
edit.
3. Press the G button to display the Programme edit menu.
Programme edit
PR
OK
VOL
VOL
0 C 03
1 BLN 03
2 C 12
3 S 66
4 S 67
5
6
7
8
9
Delete
Move
PR
DE F G
1
2
3
4
5
6
7
8
9
S
S
S
C
C
69
17
22
09
11
Copy
Skip
OK MENU
Deleting a programme
1. Select a programme to be deleted with the D / E or F / G button.
2. Press the RED button twice.
The selected programme is deleted, all the following
programmes are shifted up one position.
Programme edit
0
0 C 03
1 BLN 03
2 C 12
3 S 66
4 S 67
5
6
7
8
9
S
S
S
C
C
69
17
22
09
11
Delete
MENU
LIGHTING
Copying a programme
1. Select a programme to be copied with the D / E or F / G button.
2. Press the GREEN button.
All the following programmes are shifted down one position.
Moving a programme
1. Select a programme to be moved with the D / E or F / G button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with
the D / E or F / G button.
4. Press the YELLOW button again to release this function.
Skipping a programme number
1. Select a programme number to be skipped with the D / E or F / G
button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be
unable to select it using the D / E button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
LIGHTING
14
Repeatedly press the MENU button to return to normal TV viewing.
ENGLISH
Setting up TV stations
Favourite programme
Station
This function lets you select your favourite programmes directly.
1. Press the MENU button and then D / E button to select the
Auto programme
Manual programme
Programme edit
Favourite programme
STATION menu.
2. Press the G button and then
programme.
D
/
E
to select Favourite
DE
FG
OK MENU
Station
Auto programme
Manual programme
Programme edit
Favourite programme
DE
FG
Off
-- ------ ------ ------ ------ ------ ------ ------ -----
G
LIST
MENU
OK MENU
Press the G button and then F / G button to select On or Off.
Press the D / E button to select - - - - - - - .
Select a desired programme with the F / G button.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
7. Repeatedly press the MENU button to return to normal TV
3.
4.
5.
6.
PR
OK
VOL
VOL
PR
viewing.
Repeatedly press the YELLOW button to select stored favourite
programmes while it is selected On. Repeatedly press the YELLOW button to select previous programmes while it is selected Off.
Calling the programme table
You can check the programmes stored in the memory by displaying
the programme table.
Displaying programme table
Press the LIST button to display the Programme table menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
Programme List
0 C 03
1 BLN 03
2 C 12
3 S 66
4 S 67
DE F G
5
6
7
8
9
S
S
S
C
C
69
17
22
09
11
OK MENU
Note :
a. You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
b. Some programmes with the channel number shown in the
programme table indicate there is no station name assigned.
Selecting a programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The set switches to the chosen programme number.
Paging through a programme table
There are 10 programme table pages in which contain 100
programmes.
Pressing the D / E or F / G button repeatedly turns the pages.
Press the MENU button to return to normal TV viewing.
15
Picture adjustment
PSM (Picture Status Memory)
Picture
PSM
CSM
XD
Cinema
Reset
DE
FG
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select PSM.
3. Press the G button and then D / E button to select a picture setting on the PSM menu.
4. Press the OK button.
OK MENU
Picture
PSM
CSM
XD
Cinema
Reset
MENU
PR
DE
OK MENU
5. Repeatedly press the MENU button to return to normal TV
OK
VOL
VOL
FG
Dynamic
Standard
Mild
Game
User
G
PR
viewing.
You can also recall a desired picture (Dynamic, Standard, Mild,
Game or User) with PSM button on the remote control. The picture
Dynamic, Standard, Mild and Game are programmed for optimum
picture reproduction at the factory and cannot be changed.
Picture adjustment
You can adjust picture contrast, brightness, colour intensity,
sharpness to the levels you prefer.
PSM
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select PSM.
3. Press the G button and then D / E button to select User.
4. Press the G button and then D / E button to select the desired
picture item.
5. Press the G button and then F / G button to make appropriate
adjustments.
User
Contrast
Brightness
Colour
Sharpness
Tint
100 G
50
50
50
0
Contrast
85
F
G
E
DE
FG
OK MENU
6. Repeatedly press the MENU button to return to normal TV
viewing.
16
ENGLISH
Picture adjustment
CSM (Colour Status Memory)
Picture
Selecting a factory setting colour set.
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select CSM.
PSM
CSM
XD
Cinema
Reset
DE
FG
Picture
PSM
CSM
XD
Cinema
Reset
DE
FG
G
OK MENU
Cool
Normal
Warm
User
OK MENU
3. Press the G button and then D / E button to select a color setting on the CSM menu: Cool, Normal, Warm or User (Red,
Green, Blue).
4. Press the OK button.
5. Repeatedly press the MENU button to return to normal TV
MENU
PR
viewing.
OK
VOL
VOL
PR
17
Picture adjustment
Picture
XD function
PSM
CSM
XD
Cinema
Reset
XD is LG electronic's unique picture improving technology to display a
real HD source through an advanced digital signal processing algorithm.
DE
FG
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select XD.
3. Press the G button and then D / E button to select Auto or
OK MENU
Manual.
Picture
PSM
CSM
XD
Cinema
Reset
DE
MENU
VOL
PR
Auto
Manual
OK MENU
4. Press the OK button.
5. Repeatedly press the MENU button to return to normal TV
viewing.
Selecting the Manual
PR
OK
VOL
FG
G
This menu is activatived after selecting the User of PSM.
1. Press the G button and then D / E button to select XD
Contrast, XD Colour or XD NR.
2. Press the G button and then D / E button to select On or Off.
3. Repeatedly press the MENU button to return to normal TV
viewing.
XD Contrast : Optimizing the contrast automatically according to the
brightness of the reflection.
XD Colour : Adjusting the colors of the reflection automatically to
reproduce as closely as possible to the natural colors.
XD NR : Removing the noise up to the point where it does not damage the original picture.
Manual
XD Contrast
XD Colour
XD NR
DE
FG
G
On
Off
OK MENU
Note: XD NR is not available in Component, RGB, HDMI.
18
ENGLISH
Picture adjustment
Cinema
Picture
PSM
CSM
XD
Cinema
Reset
Set up the TV for the best picture appearance for viewing movies.
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select Cinema.
3. Press the
G
button and then
D /E
button to select On or Off.
DE
FG
OK MENU
Picture
PSM
CSM
XD
Cinema
Reset
DE
FG
G
On
Off
OK MENU
4. Repeatedly press the MENU button to return to normal TV
viewing.
Note: This feature is available in TV, AV, Component.
MENU
Reset
Returns to the default settings PSM, CSM, XD, Cinema at the
factory.
1. Press the MENU button and then D / E button to select the
PICTURE menu.
2. Press the G button and then D / E button to select Reset.
3. Press the G button to initialize the adjusted value.
PR
OK
VOL
VOL
PR
Picture
PSM
CSM
XD
Cinema
Reset
DE
FG
G
To set
OK MENU
4. Repeatedly press the MENU button to return to normal TV
viewing.
19
Sound adjustment
SSM (Sound Status Memory)
Sound
SSM
AVL
Balance
You can select your preferred sound setting; Flat, Music, Movie or
Sports and you can also adjust the sound frequency of the equalizer.
1. Press the MENU button and then D / E button to select the
SOUND menu.
0
Sound
DE
FG
SSM
AVL
Balance
OK MENU
G
0
Flat
Music
Movie
Sports
User
MENU
DE
PR
OK
VOL
VOL
PR
FG
OK MENU
2. Press the G button and then D / E button to select SSM.
3. Press the G button and then D / E button to select a sound
setting on the SSM menu.
Sound Frequency Adjustment
a. Press the OK button in User.
b. Select a sound band by pressing the F / G button.
c. Make appropriate sound level with the D / E button.
d. Press the OK button to store it for the sound User.
User
0.1 0.5 1.2 5.0 10 kHz
DE
SSM
FG
OK MENU
4. Repeatedly press the MENU button to return to normal TV viewing.
You can also recall a desired sound setting (Flat, Music, Movie, Sports
or User) with SSM button on the remote control. The sound settings
Flat, Music, Movie and Sports are programmed for optimum sound
reproduction at the factory and cannot be changed.
Note : If you press the SSM button after making appropriate
adjustment on the User sub menu, the display User automatically
appears even though you have already set a factory preset setting;
Flat, Music, Movie or Sports.
Sound
SSM
AVL
Balance
DE
FG
G
0
On
Off
OK MENU
Sound adjustment
You can adjust balance, AVL (Auto Volume Leveler).
AVL automatically keeps on an equal volume level even if you
change programmes.
1. Press the MENU button and then D / E button to select the
SOUND menu.
2. Press the G button and then D / E button to select the desired
sound item; AVL or Balance.
3. Make desired adjustment with the D / E, F / G and then press
the OK button.
4. Repeatedly press the MENU button to return to normal TV viewing.
20
ENGLISH
Sound adjustment
Stereo/Dual reception
When a programme is selected, the sound information for the
station appears after the programme number and station name
disappear.
Broadcast
Mono
Stereo
Dual
On Screen Display
MONO
STEREO
DUAL I
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II
button twice again.
I/II
Language selection for dual language broadcast
If a programme is received in two languages (dual language), you
can switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II
button repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the
loudspeakers.
DUAL I+II sends a separate language to each loudspeaker.
NICAM reception
If your set is equipped with the receiver for NICAM reception, the
high quality NICAM (Near Instantaneous Companding Audio
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
1. When NICAM mono is received, you can select NICAM MONO
or FM MONO.
2. When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
3. When NICAM dual is received, you can select NICAM DUAL I,
NICAM DUAL II or NICAM DUAL I+II or MONO. When FM
mono is selected the display MONO appears on the screen.
Sound output selection
In AV mode, you can select output sound for the left and right loudspeakers.
Repeatedly press the I/II button to select the sound output.
L+R : Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loudspeaker.
L+L : Audio signal from audio L input is sent to left and right loudspeakers.
R+R : Audio signal from audio R input is sent to left and right loudspeakers.
21
TIME Menu
Clock
Time
Clock
Off time
On time
Auto sleep
DE
FG
You must set the time correctly before using on/off time function.
1. Press the MENU button and then D / E button to select the
TIME menu.
2. Press the G button and then D / E button to select Clock.
OK MENU
Time
Clock
Off time
On time
Auto sleep
DE
FG
G
--:--
OK MENU
3. Press the G button and then D / E button to adjust the hour.
4. Press the G button and then D / E button to adjust the minute.
5. Press the MENU button to save.
MENU
On/Off time
The off timer automatically switches the set to standby at the
preset time.
PR
OK
VOL
VOL
PR
1. Press the MENU button and then D / E button to select the
TIME menu.
2. Press the G button and then D / E button to select Off time or
On time.
3. Press the G button and then D / E button to select On.
To cancel On/Off time function, press the D / E button to
select Off.
Time
Clock
Off time
On time
Auto sleep
DE
FG
G
--:-Pr.
0
Vol. 30
On
OK MENU
4. Press the G button and then D / E button to adjust the hour.
5. Press the G button and then D / E button to adjust the minute.
6. Only On time function; Press the G button and then D / E
button to adjust volume level and programe number.
7. Press the MENU button to save.
Note :
a. In the event of power interruption (disconnection or power
failure), the clock must be reset.
b. Two hours after the set is switched on by the on time function it
will automatically switch back to standby mode unless a button
has been pressed.
c. Once the on or off time is set, these functions operate daily at
the preset time.
d. Off Timer function overrides On Timer function if they are set to
the same time.
e. The set must be in standby mode for the On Timer to work.
22
ENGLISH
TIME Menu
Auto sleep
Time
If you select On on the Auto sleep menu, the set will automatically switch itself to standby mode approximately ten minutes after a
TV station stops broadcasting.
1. Press the MENU button and then D / E button to select the
TIME menu.
2. Press the G button and then D / E button to select Auto sleep.
3. Press the G button and then D / E button to select On or Off.
Clock
Off time
On time
Auto sleep
DE
FG
OK MENU
Time
Clock
Off time
On time
Auto sleep
MENU
G
On
Off
PR
DE
FG
OK
OK MENU
4. Press the MENU button to save.
VOL
VOL
PR
Sleep timer
You don’t have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the preset time has elapsed.
Press the SLEEP button to select the number of minutes.
The display ‘
---’ will appear on the screen, followed by 10, 20,
30, 60, 90, 120, 180 and 240. The timer begins to count down from
the number of minutes selected.
Note :
a. To view the remaining sleep time, press the SLEEP button
once.
b. To cancel the sleep time, repeatedly press the SLEEP button
until the display ‘
---’ appears.
c. When you switch the set off, the set releases the preset sleep
time.
SLEEP
23
Other functions
Child lock
Special
Language
Country
Child lock
Lighting
XD Demo
DE
FG
The TV can be set so that the remote control handset is needed to
control it. This feature can be used to prevent unauthorized viewing.
OK MENU
MENU
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Child lock.
3. Press the G button and then D / E button to select On or Off
on the Child lock menu.
Special
Language
Country
Child lock
Lighting
XD Demo
PR
G
On
Off
OK
VOL
VOL
DE
FG
OK MENU
PR
4. Press the MENU button to save.
5. Repeatedly press the MENU button to return to normal TV
viewing.
LIGHTING
With the lock on, the display Child lock on appears on the screen
if any button on the top panel is pressed while viewing the TV.
LED Lighting
Use this function to set the LED Lighting On or Off, which is red in
color back of the stand of product. If you set On at any time, the
LED Lighting will automatically be turned on.
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select Lighting.
3. Press the G button and then D / E button to select On or Off
on the Lighting menu.
Special
Language
Country
Child lock
Lighting
XD Demo
DE
LIGHTING
24
FG
G
On
Off
OK MENU
4. Repeatedly press the MENU button to return to normal TV
viewing.
ENGLISH
Other functions
XD Demo
Special
Use it to see the difference between XD Demo on and XD Demo
off.
Language
Country
Child lock
Lighting
XD Demo
1. Press the MENU button and then D / E button to select the
SPECIAL menu.
2. Press the G button and then D / E button to select XD Demo.
3. Press the G button to begin XD Demo.
DE
FG
OK MENU
Special
Language
Country
Child lock
Lighting
XD Demo
DE
FG
G
To start
OK MENU
MENU
4. Press the MENU button to return to normal TV viewing.
PR
OK
VOL
VOL
• XD Demo
XD™ Off
XD™ On
PR
Menu Exit
25
Other functions
TV, AV and PC modes
Press the INPUT button and then D / E button to select desired
mode.
Inputs can be set for TV, AV or PC mode. AV mode is used when a
video cassette recorder (VCR), or other equipment is connected to
the set.
INPUT
Note : When a VCR is connected via the aerial socket the set is
used in TV mode. See the ‘Connection of external equipment’ section.
Input
PR
OK
VOL
VOL
PR
TV
AV
Component
RGB
HDMI/DVI
DE
1
2
3
4
5
6
7
8
9
0
OK
The AV and PC modes are :
• AV : VCR connected to the Euro scart socket of the set.
• RGB-DTV : SET TOP connected to the PC INPUT and PC
SOUND socket.
• RGB-PC : PERSONAL COMPUTER connected to the PC
socket.
• Component : DVD connected to the D-SUB sockets and
AUDIO IN on the back of set.
• HDMI-DTV : DVD connected to the HDMI sockets on the back
of set.
• HDMI-PC : PERSONAL COMPUTER connected to the HDMI
sockets on the back of set.
Auto AV switching
If your VCR outputs an AV switching voltage when connected to the
Euro scart socket, the set will switch to AV mode automatically. But if
you want to keep on watching TV mode, press the D / E or NUMBER buttons.
26
ENGLISH
Teletext
- This feature is not available in all countries.
Teletext (or TOP text) is an optional function, therefore only a set with
the teletext system can receive the teletext broadcast.
Teletext is a free service broadcast by most TV stations which gives upto-the-minute information on news, weather, television programmes,
share prices and many other topics.
The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of
pages which are selected by directly entering the corresponding page
number. TOP and FASTEXT are more modern methods allowing quick
and easy selection of teletext information.
PR
OK
VOL
VOL
PR
1
2
3
4
5
6
7
8
9
Switch on/off
Press the TEXT button to switch to teletext. The initial page or last page
appears on the screen.
Two page numbers, TV station name, date and time are displayed on
the screen headline. The first page number indicates your selection,
while the second shows the current page displayed. Press the TEXT
button to switch off teletext. The previous mode reappears.
SIMPLE text
Page selection
1. Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number,
you must complete the three digit number and then re-enter the correct page number.
2. The D / E button can be used to select the preceding or following
page.
Programming a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
button to switch to LIST mode.
0
TEXT
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
?
INDEX
i
MODE
M
M
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on the
remote control handset.
1. Press a coloured button.
2. Using the NUMBER buttons, select the page you wish to programme.
3. Press the OK button. Then the selected page is stored as the
selected page number by blinking once. From now on, you can
select this page with the same coloured button.
4. The three other coloured buttons are programmed in this way.
LIGHTING
27
Teletext
TOP text
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen. The yellow field
denotes the next group and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing page with automatic overflow to the next
group. Alternatively the D button can be used.
4. The red button permits to return to previous selection. Alternatively the E button can be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode.
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by pressing the
corresponding coloured button.
Page selection
1. Press the i button to select the index page.
2. You can select the pages which are colour coded along the bottom line with the same coloured buttons.
3. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page
number with the NUMBER buttons in FASTEXT mode.
4. The D / E button can be used to select the preceding or following page.
Special teletext functions
?
REVEAL
Press this button to display concealed information, such as solutions of riddles or puzzles.
Press this button again to remove the information from the display.
SIZE
Selects double height text.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of the page.
Press this button again to return to the normal display.
UPDATE
Displays the TV picture on the screen while waiting for the new teletext page.
The display
will appear at the top left hand corner of the screen. When the updated page
is available then display
will change to the page number.
Press this button to view the updated teletext page.
HOLD
Stops the automatic page change which will occur if a teletext page consists of 2 or more sub
pages.
The number of sub pages and the sub page displayed is, usually, shown on the screen below
the time. When this button is pressed the stop symbol is displayed at the top left-hand corner
of the screen and the automatic page change is inhibited.
To continue press this button again.
MIX
Displays the teletext pages superimposed on the TV picture.
To switch the TV picture off press this button again.
TIME
When viewing a TV programme, press this button to display the time at the top right hand corner of the screen. Press this button again to remove the display. In the teletext mode, press this
button to select a sub page number. The sub page number is displayed at the top left hand corner of the screen. To hold or change the sub page, press the NUMBER buttons.
Press again to exit this function.
28
ENGLISH
Connection of external equipment
You can connect additional equipment, such as VCRs, camcorders
etc. to your set. Examples are shown below.
Aerial socket
1. Connect the RF out socket of the VCR to the aerial socket of
the set.
2. Connect the aerial cable to the RF aerial in socket of the VCR.
3. Store the VCR channel on a desired programme number using
the ‘Manual programme tuning’ section.
4. Select the programme number where the VCR channel is
stored.
5. Press the PLAY button on the VCR.
HDMI
DVI IN
AV
RJ12
AUDIO IN
D-SUB
RGB/DVI
COMPONENT
PC/DVI
COMPONENT
ANTENNA
IN
DC-IN
VCR
Euro scart socket (VCR)
1. Connect the Euro scart socket of the VCR to the Euro scart
socket of the set.
2. Press the PLAY button on the VCR.
If your VCR outputs an AV switching signal via the Scart lead the
set will auto switch to AV mode on start of playback, but if you
want to keep on watching in TV mode, press the D / E or NUMBER buttons.
Otherwise press the INPUT button on the remote control
handset to select AV. The VCR play back picture appears on
the screen.
You can also record programmes received by the TV on video
tape.
HDMI
DVI IN
AV
RJ12
AUDIO IN
D-S
RGB/DVI
COMPONENT
PC/
COMPO
VCR
Note :
a. Signal type RGB, i.e. the signals red, green and blue can only
be selected for the Euro scart and the AV can be received.
These signals are transmitted, for example, by a pay TV
decoder, game machine or photo CD unit, etc.
b. Please use shielded scart cable.
29
Connection of external equipment
DVD input sockets
HDMI
DVI IN
AV
RJ12
AUDIO IN
D-SUB
RGB/DVI
COMPONENT
PC/DVI
COMPONENT
Euro scart socket
1. Connect the Euro scart socket of the DVD to the Euro scart
socket of the set.
2. Press the INPUT button to select AV.
3. Press the PLAY button on the DVD.
The DVD playback picture appears on the screen.
DVD
RGB in socket
1. Connect the DVD output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y
or Y PB PR) of the DVD to the D-SUB sockets of the set. Audio
cable of the SET TOP to the AUDIO IN.
2. Press the INPUT button to select Component.
HDMI
DVI IN
AV
RJ12
AUDIO IN
D-SUB
RGB/DVI
COMPONENT
PC/DVI
COMPONENT
ANTENNA
IN
DC-IN
HDMI sockets
1. Connect the HDMI output of the DVD to the HDMI DVI IN jack
on the set.
2. Select HDMI input source with using the INPUT button on the
remote control.
DVD
DTV in sockets
HDMI
DVI IN
AV
RJ12
RGB in socket
AUDIO IN
1. Connect the SET TOP with the DTV output sockets (Y Cb Cr, Y Pb
Pr, Y B-Y R-Y or Y PB PR) to D-SUB socket on the set and audio
cable of the SET TOP to the AUDIO IN.
2. Press the INPUT button to select Component.
RGB/DVI
COMPONENT
DVD
HDMI sockets
1. Connect the HDMI output of the digital set-top box to the HDMI
DVI IN jack on the set.
2. Select HDMI input source with using the INPUT button on the
remote control.
HDMI
DVI IN
AV
RJ12
AUDIO IN
D-SUB
RGB/DVI
COMPONENT
PC/DVI
COMPONENT
ANTENNA
IN
DC-IN
DTV Reciever
HDMI
DVI IN
AV
DTV Reciever
30
RJ12
AUDIO IN
D-
RGB/DVI
COMPONENT
P
COM
ENGLISH
Connection of PC
PC in socket
RGB in socket
1. Connect the signal cable from the monitor output socket of the
PERSONAL COMPUTER to the PC input socket of the set.
2. Connect the audio cable from the PC to the AUDIO IN sockets
of the set.
3. Press the INPUT button to select RGB (or RGB [PC]).
4. Switch on the PC, and the PC screen appears on the set.
The set can be operated as the PC monitor.
MI
IN
AV
RJ12
AUDIO IN
D-SUB
RGB/DVI
COMPONENT
PC/DVI
COMPONENT
ANTENNA
IN
DC-IN
PERSONAL COMPUTER
HDMI sockets
1. Connect the DVI output of the PC to the HDMI DVI IN jack on
the set.
2. Connect the audio cable from the PC to the AUDIO IN sockets
of the set.
3. Select HDMI/DVI [PC] input source with using the INPUT button
on the remote control.
HDMI
DVI IN
AV
RJ12
AUDIO IN
D-S
RGB/DVI
COMPONENT
PC/
COMPO
PERSONAL COMPUTER
Displayable Monitor Specification
MODE Resolution
Horizontal
Vertical
Frequency(kHz) Frequency(Hz)
VGA
640x480
31.4
60
SVGA
800x600
37.8
60
XGA
1024x768
1280x768
48.3
47.7
60
60
WXGA
1360x768
47.7
60
(Synchronization input form : separate)
Note :
a. If the set is cold, there may be a small “flicker” when the set is switched on. This is normal, there is
nothing wrong with the set.
b. If possible, use the VESA 1360x768@60Hz video mode to obtain the best image quality for your
LCD monitor. If used under the other resolutions, some scaled or processed pictures may appear
on the screen. The set has been pre-adjusted to the mode VESA 1360x768@60Hz.
c. Some dot defects may appear on the screen, like Red, Green or Blue spots. However, this will have
no impact or effect on the monitor performance.
d. Do not press the LCD screen with your finger for a long time as this may produce some temporary
distortion effects on the screen.
e. When the PC screen appears on the set, a message may appear on the screen, and the message
will differ according to the Window system version. If a message appears click “Next” until the
message finishes.
f. If the message “No signal” appears on the screen, adjust the PC as in the ‘Displayable Monitor
Specification’ section.
31
Connection of PC
PC Setup
Screen
Auto config.
Manual config.
XGA Mode
You can adjust auto configure, manual configure and reset as you
prefer.
ARC
Reset
DE
FG
1. Press the INPUT button and then D / E button to select the
RGB [PC].
2. Press the MENU button and then D / E button to select the
Screen menu.
3. Press the G button and then D / E button to select the desired
screen function.
OK MENU
Screen
Auto config.
Manual config.
XGA Mode
INPUT
G
To set
ARC
Reset
MENU
DE
FG
OK MENU
4. Make appropriate adjustments.
PR
Auto configure
OK
VOL
VOL
PR
This function is for the automatic adjustment of the screen position, clock and phase. The displayed image will disappear for a
few seconds while the Auto-configuration is in progress.
Manual configure
This function is for the manual adjustment of the screen position, clock and phase. Press the F / G button to make appropriate adjustments.
• H-Position / V-Position
This function is to adjust picture to left/right and up/down as you
prefer.
• Clock
This function is to minimize any vertical bars or stripes visible on
the screen background. And the horizontal screen size will also
change.
• Phase
This function allows you to remove any horizontal noise and
clear or sharpen the image of characters.
Reset
This function allows you to return to the good picture reproduction programmed at the factory and cannot be changed.
Note : Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor’s position, clock and phase manually.
5. Press the OK button to store it for the PC monitor picture.
32
ENGLISH
Connection of PC
Selecting wide XGA mode
Screen
Auto config.
Manual config.
XGA Mode
To see a normal picture, match the resolution of RGB mode and
selection of XGA mode.
ARC
Reset
1. Press the MENU button and then D / E button to select the
Screen menu.
2. Press the G button and then D / E button to select XGA mode.
3. Press the G button and then D / E button to select the desired
XGA resolution.
DE
FG
OK MENU
Screen
Auto config.
Manual config.
XGA Mode
ARC
Reset
DE
FG
G
1024x768
1280x768
1360x768
MENU
OK MENU
4. Repeatedly press the MENU button to return to normal TV
viewing.
PR
OK
VOL
VOL
PR
33
Picture format
You can watch TV in various picture formats; Spectacle, Original,
4:3, 16:9, 14:9, Zoom1, Zoom2.
Repeatedly press the ARC button to select your desired picture
format.
PR
OK
VOL
VOL
PR
Spectacle
When your TV receives the wide screen signal, it will lead you to
adjust the picture horizontally, in a nonlinear proportion, to fill the
entire screen.
Original
When your TV receives the wide screen signal, it will be automatically
changed to the picture format to be sent. (Not available in all countries)
4:3
This picture format is 4 to 3 of general TV.
ARC
16:9
You can enjoy the cinema (the picture format of 16:9) or general TV
programme through the 16:9 mode.
The screen 16:9 is viewed just like that but the screen 4:3 is
magnified to the left and right so that the screen 16:9 is full.
14:9
You can enjoy the picture format of 14:9 or general TV programme
through the 14:9 mode.
The screen 14:9 is viewed just like that the screen 4:3 is magnified
to the upper / lower and left / right.
Zoom1
Following selection will lead you to view the picture without any alternation, while filling the entire screen. However, the top and bottom portions
of the picture will be cropped.
Zoom2
Choose Zoom2 when you want the picture to be altered, both horizontally extended and vertically cropped. The picture taking a
halfway trade off between alteration and screen coverage.
Note : ARC menu is not available in RGB, HDMI, Component
mode exept 4:3, 16:9. You cn adjust the enlarge proportion using
D / E button.
34
ENGLISH
External Control Device Setup ; RJ-12
- Connect the RJ-12 input jack to an external control device (such as a Interface box) and control the
TV’s functions externally.
- Connect the RJ-12 (communication) port of the control device to the RJ-12 jack on the TV back
panel.
- RJ-12 connection cable is not supplied with the TV.
RJ-12 Setup
Interface box
RJ-12
PC
RJ-12
Type of Connector; RJ-12 6-Pin Male
No.
1
2
3
4
5
6
Signal
NC
GND
RX
ST_5V
TX
NC
1 2 3 4 5 6
Signal requirements
Not connected
Power ground
Standard RS232 specification
400 mA 5VDC 5%, max 100mV ripple
Standard RS232 specification
Female connector on box, viewed
towards connector.
RJ-12 Configurations
3-Wire Configurations
(Standard RJ-12 cable)
NC
GND
RX
ST_5V
TX
NC
TV
PC
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
RX
TX
IR-Out
GND
35
External Control Device Setup ; RJ-12
Set ID
- Use this function to specify a monitor ID number.
- Refer to ‘Real Data Mapping 1’. See page 37.
- Set ID Setup is located in service menu. (ADJ => MENU => Set ID Setup)
Installation Menu V2.0
LG Hotel Mode setup
TVLink Loader
Password Change
Set ID Setup
G
Set ID setup
G
G
G
Set ID Lock
Set ID
No
1
MCU Version 1.78
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
• Stop bit : 1 bit
• Communication code : ASCII code
* Use a crossed (reverse) cable.
Command Reference List
COMMAND COMMAND DATA
(Hexa)
2
1
01. Power
k
a
00 ~ 01
02. Input Select
k
b
00 ~ 09
03. Aspect Ratio
k
c
00 ~ 07
04. Screen Mute
k
d
00 ~ 01
05. Volume Mute
k
e
00 ~ 01
06. Volume Control
k
f
00 ~ 64
07. Contrast
k
g
00 ~ 64
08. Brightness
k
h
00 ~ 64
09. Color
k
i
00 ~ 64
10. Tint
k
j
00 ~ 64
11. Sharpness
k
k
00 ~ 0A
12. OSD Mute
k
l
00 ~ 01
13. Key Lock
k
m
00 ~ 01
14. Balance
k
t
00 ~ 64
15. Color Preset - CSM
k
u
00 ~ 03
16. Auto Configure
j
u
00 ~ FF
17. Key
m
c
IR List
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: First command. (j, k or m)
* [Command 2]: Second command.
* [Set ID]: Adjustment range is 1 ~ 99. When selecting Set ID
‘0’, every connected TV set is controlled. Set ID is
indicated as decimal (1~99) on menu and as
Hexa decimal (0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit ‘FF’ data to read status of command.
* [Cr]: Carriage Return
ASCII code ‘0x0D’
* [ ]: ASCII code ‘space (0x20)’
* Set ID & DATA have two characters, for example ‘00’, ‘30’...
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from non-viable
functions or communication errors.
36
ENGLISH
External Control Device Setup ; RJ-12
01. Power On (Command:a)
05. Volume Mute (Command:e)
G To control Power On/Off of the TV.
G To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01
: Power On
Acknowledgement
[k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute off (Volume on)
01 : Volume mute on (Volume off)
[a][ ][Set ID][ ][OK][Data][x]
Acknowledgement
02. Input Select (Command:b) (Main Picture Input)
[e][ ][Set ID][ ][OK][Data][x]
G To select input source for the TV.
You can also select an input source using the TV/VIDEO
button on the TV's remote control.
06. Volume Control (Command:f)
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 00 ~ 01 : TV
02 ~ 03 : AV
04 ~ 05 : Component
06 ~ 07 : RGB
08 ~ 09 : HDMI/DVI
G To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64 (transmit by Hexadecimal code)
• Refer to ‘Real data mapping 1’ as shown below.
Acknowledgement
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
[f][ ][Set ID][ ][OK][Data][x]
03. Aspect Ratio (Command:c) (Main picture format)
07. Contrast (Command:g)
G To adjust the screen format.
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
Screen menu.
Transmission
G To adjust screen contrast.
You can also adjust contrast in the Picture menu.
[k][c][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64 (transmit by Hexadecimal code)
• Refer to ‘Real data mapping 1’ as shown below.
Data 00
01
02
03
:
:
:
:
Original
Normal screen (4:3)
Wide screen (16:9)
Spectacle
04 : Zoom1
05 : Zoom2
06 : Original
07 : 14:9
* Spectacle / Zoom1,2 / Original / 14:9 is not available in
Component / RGB / HDMI mode.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
08. Brightness (Command:h)
Acknowledgement
G To adjust screen brightness.
You can also adjust brightness in the Picture menu.
[c][ ][Set ID][ ][OK][Data][x]
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
04. Screen Mute (Command:d)
G To select screen mute on/off.
Transmission
Data Min : 00 ~ Max : 64 (transmit by Hexadecimal code)
• Refer to ‘Real data mapping 1’ as shown below.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
[k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on)
01 : Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
* Real data mapping 1
* Real data mapping 2
00 : Step 0
00: Step 0
0A : Step 10
01: Step 10
0F : Step 15
10 : Step 16
05: Step 50
06: Step 60
64 : Step 100
0A :
Step 100
* Tint : -50 ~ +50
37
External Control Device Setup ; RJ-12
09. Color (Command:i)
14. Balance (Command:t)
G To adjust the screen color.
You can also adjust color in the Picture menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
G To change sound Balance (L/R) on the TV.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 ~ Max : 64 (transmit by Hexadecimal code)
• Refer to ‘Real data mapping 1’. See page 37.
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Data Min: 00(L50) ~ Max: 64(R50) (transmit by
Hexadecimal code)
• Refer to ‘Real data mapping 1’. See page 37.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
10. Tint (Command:j)
G To adjust the screen tint.
You can also adjust tint in the Picture menu.
Transmission
15. Color Preset - CSM (Command:u)
G To change Color Preset(CSM) on the TV
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
[k][u][ ][Set ID][ ][Data0][ ][Cr]
Data Min : Red 00 ~ Max : Green 64 (transmit by
Hexadecimal code)
• Refer to ‘Real data mapping 1’. See page 37.
Acknowledgement
Min : 00 ~ Max : 03(transmit by Hexadecimal code)
[j][ ][Set ID][ ][OK][Data][x]
Data 00
01
: Cool
: Normal
02
03
: Warm
: User
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command:k)
G To adjust the screen sharpness.
You can also adjust sharpness in the Picture menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
16. Auto Configure (Command:j u)
G To execute Auto configure. (Only RGB-PC)
Transmission
[j][u][ ][Set ID][ ][Data 0][Cr]
Data Min : 00 ~ Max : 0A (transmit by Hexadecimal code)
• Refer to ‘Real data mapping 2’. See page 37.
Acknowledgement
Min : 00 ~ Max : FF - Doesn’t have mean.
(transmit by Hexadecimal code)
[k][ ][Set ID][ ][OK][Data][x]
Acknowledgement
[u][ ][Set ID][ ][OK][Data][x]
12. OSD Mute (Command:l)
G To select OSD (On Screen Display) mute on/off.
Transmission
17. Key (Command:m c)
[k][l][ ][Set ID][ ][Data][Cr]
Transmission
Data 00: OSD mute on
Acknowledgement
01: OSD mute off
G To execute key command by send IR code with RJ-12.
[m][c][ ][Set ID][ ][Data][Cr]
Data: : Reference IR List (transmit by Hexadecimal code)
[l][ ][Set ID][ ][OK][Data][x]
Acknowledgement
13. Key Lock (Command:m)
G To lock the remote control and the front panel controls on
the TV.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off
Acknowledgement
01: Lock on
[m][ ][Set ID][ ][OK][Data][x]
• If you’re not using the remote control and front panel controls
on the TV, use this mode. When main power is on/off,
remote control lock is released.
38
[c][ ][Set ID][ ][OK][Data][x]
ENGLISH
External Control Device Setup ; RJ-12
Key code
Code (Hexa)
00
01
02
03
08
C4
C5
09
10~19
0E
43
44
79
4D
52
98
D6
5A
BF
C6
D5
76
AF
Function
PR D
PR E
Vol G
Vol F
Power On/Off
Power ON
Power OFF
MUTE
Number Key 0~9
Sleep
Menu
OK
ARC
PSM
SSM
Source
TV
AV
Component
HDMI/DVI
RGB
ARC(4:3)
ARC(ZOOM)
Note
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power)
Discrete IR code (Only Power On)
Discrete IR code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code(Input TV Select)
Discrete IR Code(Input AV Select)
Discrete IR Code(Input Component Select)
Discrete IR Code(Input HDMI/DVI Select)
Discrete IR Code(Input RGB Select)
Discrete IR Code(Only 4:3 Mode)
Discrete IR Code(Only Zoom Mode)
39
Troubleshooting Checklist
The operation does not work normally.
The remote control
doesn’t work
• Check to see if there is any object between the product and the remote
control causing obstruction.
• Are batteries installed with correct polarity (+ to +, - to -)?
• Correct remote operating mode set: TV, VCR etc.?
• Install new batteries.
Power is suddenly
turned off
• Is the sleep timer set?
• Check the power control settings. Power interrupted
• No broadcast on station tuned with Auto off activated.
The video function does not work.
No picture &
No sound
• Check whether the product is turned on.
• Try another channel. The problem may be with the broadcast.
• Is the power cord inserted into wall power outlet?
• Check your antenna direction and/or location.
• Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
Picture appears
slowly after
switching on
• This is normal, the image is muted during the product startup process.
Please contact your service center, if the picture has not appeared after five
minutes.
No or poor color
or poor picture
• Adjust Color in menu option.
• Keep a sufficient distance between the product and the VCR.
• Try another channel. The problem may be with the broadcast.
• Are the video cables installed properly?
• Activate any function to restore the brightness of the picture.
Horizontal/vertical bars or picture shaking
• Check for local interference such as an electrical appliance or power tool.
Poor reception on
some channels
Lines or streaks
in pictures
40
• Station or cable product experiencing problems, tune to another station.
• Station signal is weak, reorient antenna to receive weaker station.
• Check for sources of possible interference.
• Check antenna (Change the direction of the antenna).
ENGLISH
Troubleshooting Checklist
The audio function does not work.
Picture OK &
No sound
No output from one
of the speakers
Unusual sound
from inside the
product
• Press the VOL (or Volume) button.
• Sound muted? Press MUTE button.
• Try another channel. The problem may be with the broadcast.
• Are the audio cables installed properly?
• Adjust Balance in menu option.
• A change in ambient humidity or temperature may result in an unusual
noise when the product is turned on or off and does not indicate a fault with
the product.
There is a problem in PC mode.
(Only PC mode applied)
The signal is out of
range.
Vertical bar or
stripe on background &
Horizontal Noise &
Incorrect position
Screen color is
unstable or single
color
• Adjust resolution, horizontal frequency, or vertical frequency.
• Check the input source.
• Work the Auto configure or adjust clock, phase, or H/V position.
• Check the signal cable.
• Reinstall the PC video card.
41
Product Specifications
Power input
AC/DC Adapter
Power Consumption
Dimensions
(Width x Depth x Height)
Weight (Net)
Television System
Programme Coverage
External Antenna Impedance
16V
3.2A
LIEN CHANG LCA02
65W
487.0mm x 166.9mm x 404.0mm
19.2inches x 6.6inches x 15.9inches
5.6kg (12.3lbs)
PAL/SECAM B/G/D/K, PAL I/II, SECAM L/L’
VHF: E2 ~ E12, UHF: E21 ~ E69, CATV: S1 ~ S20, HYPER: S21 ~ S47
75 Ω
* The specifications shown above may be changed without prior notice for quality improvement.
42
ENGLISH
MEMO
43
Download PDF