LG | 42PM3MVA | LG 42PM3MVA Owner’s Manual

PLASMA TV
OWNER'S MANUAL
Please read this manual
carefully
before
operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
mation to your dealer when you
Model number
:
Serial number
:
cover
require
and
quote this infor-
service.
Safety Warnings
Instructions
Safety
Safety
WARNING
Do not
place
sources
such
This may
-
the set in direct
as
heat
cause a
registers,
sunlight
or
stove and so
any
place
This may
-
damp place such as
it is likely to get wet.
where
cause a
heat
on.
Do not use water while
-
fire.
Do not use the set in
or
near
fire
could
or
give
an
a
bathroom
it off
cable
antenna
building
to
rain from
prevent
This may cause water
electric shock.
-
between
inside
flowing
and
or
the set
the set.
could
or
give
an
electric
from the set, switch
it from the wall outlet and contact your
or
strange smell
service centre.
This may
cause a
fire
or
could
give
an
electric shock.
outside
Do not
in.
inside the set and could
damaged
,unplug
dealer
electric shock.
damaged
cause
In case of smoke
-
Bend
This may
shock.
cleaning
give
an
attempt
your dealer
-
This may
shock.
or
to service the set
yourself.
Contact
service centre.
cause
damaged
the set
or
could
give
an
electric
Earth wire should be connected.
-
-
If the earth wire is not
connected, there is possible
electric shock caused
by
a
danger
of
the current
leakage.
If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.
During
supplier
Short-circuit
breaker
ground
to
telephone wires, lightning
rods
or
gas
pipe.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
-
This may
cause a
Do not insert any
-
This may
Do not
-
2
cause a
fire
or
could
object
fire
or
give
cause
PLASMA TV
serious
electric shock.
into the exhaust vent.
could
give
place heavy objects
This may
an
injury
on
to
a
an
electric shock.
the set.
child
or
adult.
the set from the wall
outlet and don't touch the antenna cable.
-
-
Do not connect
activity, unplug
This may
shock.
cause
damaged
the set
or
could
give
an
electric
DISCONNECTING DEVICE FROM MAINS
Power
-
storm
Mains
plug is the disconnecting
readily operable.
device. The
plug
must remain
Safety Warnings
*
instructions have two kinds of
Safety
information, and each meaning of it is
as
below.
WARNING The violation of this instruction may
cause
serious
The violation of this instruction may
cause
light injuries
NOTES
injuries
or
and
death.
even
of the
damage
product.
Take care of
danger
that may
under
happen
condition.
specific
NOTES
Never touch the power
-
This may
plug
with
wet hand.
a
Ensure the power cord doesn't trail
objects like a heater.
electric shock.
cause an
-
Disconnect from the mains and
tions before
remove
all
This may
-
bookcase
-
or
Ventilation
electric shock.
Do not
moving.
place
or an
the set in
a
built-in installation such
as a
plug in unit if power cord or plug is damaged
connecting part of the power outlet is loose.
This may
fire
cause a
or an
or
electric shock.
rack.
Dispose of
from eating
required.
-
In
case
of
used batteries
carefully
child
a
eating them,
the set
installing
place the edge of
on
its stand
a
on
table, be careful not to
-
with
this
not
This may
child
a
immediately.
speakers
This may cause the set to fall, causing serious
adult, and serious damage to the set.
Unplug
ing. Do
When
prevent
contact doctor
moving the set assembled
carry holding the speakers.
-
to
them.
When
-
any hot
connec-
the
Do not
fire
cause a
across
injury
to
a
do not
child
or
product from the wall outlet before cleanuse liquid cleaners or aerosol cleaners.
cause
damage
the set
or
could
give
an
electric shock.
the end of the table.
This may cause the set to fall, causing serious
adult, and serious damage to the set.
injury
to
a
child
or
Contact the service centre
internal
-
part
once a
year to clean the
of the set.
Accumulated dust
can cause
mechanical failure.
The distance between eyes and the screen should be
7 times the diagonal length of the screen
approx. 5
~
away.
If not, eyes will strain.
-
Unplug
the set from the wall outlet when it is left unattended
and unused for
a
-
Do not
place
an
outside antenna in the
head power lines
cuits.
-
This may
cause an
There should be
or
other electric
vicinity of overlight or power cir-
of time
or
Accumulated dust may cause a fire or
deterioration through electric leakage.
an
long periods
in the occurrence of
state of emergency.
electric shock from
electric shock.
enough
distance between
an
outside
power lines to keep the former from
the latter even when the antenna falls.
antenna and
touching
-
This may
Do not
-
pull
This may
cause an
electric shock.
the
not the cord when
plug
cause a
disconnecting.
fire.
Owner's Manual
3
Contents
Contents
Contents
Time Menu
Safety Warnings
SafetyInstructions..........................2~3
Introduction
RemoteControlKeyFunctions...................6
LocationandFunctionofControls
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.7~8
Installation
External
Equipment Viewing Setups
DisplayableMonitorSpecification
.
.
.
.
.
.
.
.
.
.
.
.
.
.9~13
.
.
.14
HDMI..................................15~16
Accessories.................................17
InstallationOptions...........................18
Operation
TurningontheSet...........................19
On-Screen Menu Language Selection (option)
.19
Channel Menu Options
Auto Programme Tuning (In Digital mode)
.20
Auto Programme Tuning (In Analogue mode)
.20
Manual Programme Tuning (In Digital mode)
.21
Manual Programme Tuning (In Analogue mode)
.21
.21
FineTuning(InAnaloguemodeonly).
.22
Assigning a Station Name (In Analogue mode only)
.22
ProgrammeEdit(InDigitalmodeonly).
.23
Programme Edit (In Analogue mode only)
5V antenna power (In Digital mode only)
.23
.23
System information (In Digital mode only)
Favourite Programme (In Analogue mode)
.24
.24
Calling up the Programme Table (In Digital mode)
.24
Calling up the Programme Table (In Analogue mode)
Picture Menu Options
PSM(PictureStatusMemory)..................25
CSM(ColorStatusMemory)....................25
.25
ManualColourTemperatureControl
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
......................................25
.26
sRGB(RGB[PC],HDMI[PC]modeonly)
ACM(ActiveColorManagement)................26
.
.
.
.
.
.
.
.
.
ManualPictureControl........................26
Sound Menu
Options
SSM(SoundStatusMemory)...................27
BBE.......................................27
AVL(AutoVolumeLeveler).....................27
AdjustingSoundControl.......................27
TVspeaker.................................28
.28
Selecting Digital Audio Output (In Digital mode only)
.28
AudioLanguage(InDigitalmodeonly)
Stereo/Dual Reception (In Analogue mode)
.29
NICAM Reception (option) (In Analogue mode)
.29
Soundoutputselection........................29
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Disposal
Options
Currenttime................................30
TimeZoneSetup............................30
SettingtheOn/OffTimer.......................31
AutoSleep.................................31
SleepTimer.................................31
Special Menu Options
SystemLockSetting.........................32
ChildLock..................................32
ISM
After
reading this
manual, keep it in a
place where the user
can refer to easily.
4
PLASMA TV
3.
4.
.
.
.
.
.
.
.
.
.32
LowPower.................................33
Demo.................................33
FactoryReset..............................33
Screen Menu Options
.34
Autoadjustment(RGB[PC]modeonly).
ManualConfigure............................34
SelectingWideVGAmode.....................34
SettingPictureFormat........................35
.
.
.
.
.
.
.
.
.
PictureSizeZoom...........................35
ScreenPosition..............................36
Cinema....................................36
NR(NoiseReduction).........................36
.36
Initializing (Reset to original factory settings for screen)
PIP (Picture-in-Picture) Feature
WatchingPIP...............................37
.37
ProgrammeSelectionforSubPicture.
.37
Selecting an Input Signal Source for the PIP
MovingthePIP(PIPmodeonly).................37
POP (Picture-out-of-Picture: Channel Scan)
.37
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PictureSize.................................37
Adjusting PIP Transparency (PIP
Teletext (option)
mode
only)
.
.
.
.
.
.
.37
Switchon/off................................38
SIMPLEText(option).........................38
TOPText(option)............................38
FASTEXT..................................39
SpecialTeletextFunctions.....................39
Miscellaneous
.40
BriefInfo.(InDigitalmodeonly).
EPG (Electronic Programme Guide) (In Digital mode only)
.40~42
.43~49
ExternalControlDeviceSetup.
IRCode(NECFormat).....................50~51
ProgrammingtheRemote..................52
ProgrammingCodes......................53
TroubleshootingChecklist......................54
ProductSpecifications.........................55
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
of your old
.
.
.
.
.
.
.
.
.
.
.
.
appliance
1. When this crossed-out wheeled bin
2.
Method
(Image Sticking Minimization)
symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
Introduction
Introduction
What is
a
Plasma
Display
?
If
voltage is inputted to gas in glass panels, ultraviolet rays are outputted and fused with a fluorescent substance.
light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160°
-
Wide
A Plasma
At this moment,
range of vision
angle
Display provides
than 160°
more
angle
range of vision
so
that you
can
get
a
without distortion from any
picture
direction.
Easy
installation
A Plasma
in the
Display is
desired place.
Big
screen
The
screen
of
a
much
Plasma
Multimedia Plasma
A Plasma
and
The
Display
can
lighter
Display
and smaller than other
is 42"
so
that you
can
same
class
products
get vivid experience
as
so
that you
if you
are
can
in
a
install the Plasma
Display
theater.
Display
be connected with
a
computer
so
that you
it
can use
as a screen
for
conference, game, internet
so on.
explanation
about coloured dots may be present
The PDP which is the
display
device of this
product
is
composed
in the manufacture of the PDP. Several coloured dots visible
manufacturers and would not
mean
that the PDP is
faulty.
sponds to this standard is regarded as acceptable. It means
We promise that we'll do our best to develop our technology
on
We
on
PDP
screen
of 0.9 to 2.2 million cells and
the
screen
would be
a
few cell defects
acceptable,
can occur
in line with other PDP
you will understand that the product which
that it could not be changed or refunded.
hope
corre-
to minimize the cell defects.
Trade Mark of the DVB
Digital Video
Broadcasting Project (1991 to 1996)
ID
Number(s):
3463: 42PX4DVA
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner's Manual
5
Introduction
Remote Control
Control
-
-
When
Key
Functions
There
using the remote control aim it at the remote control sensor of the set.
maybe a defect in consecutive operation of remote control in a specified brightness according
selects
analogue
or
D/A TV
digital mode.
POWER
switches the set
to this set.
from
on
standby
off to
or
standby.
MODE
Selects another device.
shows
a
D/A TV
INPUT
Selects the DTV, TV, AV,
or HDMI modes.
switches the set on from
INPUT
POWER
GUIDE
programme schedule.
(In Digital mode only)
VCR
TV
standby.
SUBTITLE/* (option)
switches the subtitle
ARC
on or
off in
SUBTITLE/
GUIDE
PIP PR+
SWAP
PIP PR-
PIP
Changes
SLEEP
PIP
TEXT
MENU
Digital
mode.
ARC
INPUT
SSM
PSM
SLEEP
Sets the
the
picture
sleep
format.
timer.
EXIT
SSM
To select the sound
viewing
OK
MovesthesubpicturetoD/EorF/G
appropriate
to your
programme.
EXIT
Clears all on-screen displays and returns to
TV viewing from any menu.
direction.
PSM
the
RGB
DVD
PIP
Switches the sub picture on or off.
Selects PIP, POP or DW modes.
PIPPR+/Selects a programme for the sub picture.
SWAP
Alternates between main and sub picture.
PIP INPUT
Selects the input mode for the sub picture.
SIZE
Adjusts the sub picture size.
POSITION
Adjusts
Component,
factory preset picture according
to the
TEXT
These buttons are used for teletext.
For further details, see the 'Teletext' section.
room.
INFOi/
MENU
Displays
by
on screen menus one
one.
COLOURED BUTTONS
Exits the current menu.
Memorizes menu changes.
VOL
MUTE
FAV
used for teletext
PR
Selects
settings.
menu
are
models)
or
screen
VOL D / E (Volume Up/Down)
Increases/decreases sound level.
PR D / E (Programme Up/Down)
Selects a programme.
item.
MUTE
Switches the sound on or off.
LIST
Q.VIEW
FAV
selects
NUMBER buttons
Displays
TELETEXT
INFO/ i /* (option)
displays information on top of the
whilst watching the TV.
(In Digital mode only)
D/EorF/G
menu
These buttons
programme edit.
OK
accepts your selection or displays the
current mode.
Adjusts
(only
:
LIST
the programme table.
SIZE
POSITION
INDEX
HOLD
TIME
REVEAL
MIX
I/II
a
favourite programme.
Q.VIEW
Returns to the
?
previously
viewed programme.
VCR/DVD BUTTONS
Controls
a
controls
Installing
I/II
Selects the language during dual
broadcast.
Selects the sound output.
LG video cassette recorder.
a
LG DVD
player.
Batteries
?
Open
the
?
the
battery compartment cover
batteries with correct polarity.
Install two 1.5V alkaline batteries of AA
teries with
6
PLASMA TV
on
new
batteries.
the back side and insert
type. Don't mix used bat-
language
Introduction
Location and Function of
of Controls
Controls
<Front Panel Controls>
78
INPUT
2
1.
4
on
from
Remote Control Sensor
3.
INPUT Button
Selects the
standby
or
off to
on
from
6
D / E
(Programme Up/Down)
Selects
a
programme
Switches the set
or
HDMI modes.
standby.
7.
Exits the current
Memorizes
menu
by
item.
set is turned
one.
on
from
Power Indicator
Illuminates red in
on screen menus one
or a menu
standby.
F / G (Volume Up/Down)
Adjusts the volume.
Adjusts menu settings.
MENU
Displays
PR
5
standby.
DTV, TV, AV, Component, RGB
Switches the set
VOL
OK
6.
2.
5.
3
Power Button
Switches the set
4.
1
MENU
standby mode,
Illuminates green when the
on
menu.
8.
changes.
Intelligent Eye
Adjusts picture according
to the
surrounding
conditions.
OK
Accepts
your selection
or
displays
the current mode.
Owner's Manual
7
Introduction
Location and Function of
of Controls
Controls
-
-
-
Shown is
a
simplified representation
of the set.
What is shown here may be somewhat different from your set.
This manual explains the features available on the 42PX4DVA series.
<Back Panel>
V5
S-VIDEO
VIDEO
11
L/MON
AUDIO
R
AC INPUT
1
234
1.
ANTENNA INPUT/OUTPUT
2.
HDMI(DVI VIDEO)
5
6
7
8.
/ AUDIO INPUT / RGB INPUT
Connect the monitor
output socket of the PERSONAL
COMPUTER to this socket.
Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or the EMI
Filter core along with separate cable.
3.
REMOTE CONTROL
4.
VARIABLE AUDIO OUT SOCKETS
5.
RS-232C INPUT
(CONTROL/SERVICE)
Connect to the RS-232C
6.
port
AUDIO/VIDEO IN SOCKETS
on a
PORT
EURO SCART SOCKET
Connect the
euro
scart socket of the VCR to these sockets.
(AV2),
you must
equipment
This set
the
on
an
VCR to the S-VIDEO
operates
Connect the audio out sockets of the VCR to the audio
in AV4.
COMPONENT INPUT
Connect DVD video
outputs to Y, PB, PR of COMPONENT
INPUT and audio outputs to Audio sockets of AUDIO INPUT.
PLASMA TV
to the S-Video2
Specifications
AC power. The voltage is indicated on
page. Never attempt to operate the set
on
DC power.
11. AUDIO/VIDEO IN SOCKETS
socket.
as
change
10. POWER CORD SOCKET
S-VIDEO/AUDIO IN SOCKETS
8
this port will not work.
mode.
to these sockets.
7.
standby mode,
scart socket 2
PC.
Connect the audio/video out sockets of external
sockets
10
DIGITAL AUDIO OPTICAL OUTPUT
Used to connect either an external amplifier, or add a subwoofer to your surround sound system if it has a digital
audio optical input.
Note: In
9.
9
Note:
a. If you want to use the EURO scart cable, you have to
use the signal shielded Euro scart cable.
b. If the S-VIDEO(Y/C) signal is received through the Euro
(AV4)
Connect the S-VIDEO out socket of
8
(AV5)
S-VIDEO/AUDIO IN SOCKETS
Installation
External
Equipment
V
iewing
Viewing
Setups
Setups
Antenna Connection
-
-
Be careful not to bend the bronze wire when
5V antenna power works In
Apartments
(connecting
Digital
mode
to wall antenna
connecting to an
only. (Refer to p. 23)
antenna
port.
socket)
wall antenna socket
RF coaxial wire
(75 ohms)
<
Back
panel
of the set
>
VHF antenna
UHF antenna
outdoor antenna
Private house
(connecting
to wall outdoor
antenna)
Watching VCR
-
-
-
-
When
connecting
(R) -red).
Connect the VIDEO OUTPUT socket
-
Or,
(yellow)
to the VIDEO INPUT
on
connecting ports (Video
-
yellow,
Audio
(L)
-
the set.
a
To
a
regular
VCR
input.
Use the orbiter function to Avoid
If
white, Audio
connect the Euro scart socket of the VCR to the Euro scart socket of the set.
ture from
-
equipment,
match the colours of
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set.
If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting
to the Video
-
the set to external
a
VCR.
(Refer
to p.
having
a
fixed
image
remain
on
the
screen
for
a
long period
of time.
Typically
a
frozen still
pic-
32)
picture format is used; the fixed image may remain visible on the screen.
avoid picture noise (interference), leave an adequate distance between the VCR
4:3
and the set.
<
Back
panel
of the set
>
TV programmes
Turn the set on and select the programme you
Watching
-
want.
Watching
1.
Use the INPUT button
select
-
VCR
on
the remote control to
AV1, AV2, S-Video2, AV3, AV4
AV5.
If both S-VIDEO and VIDEO sockets have been
connected to the S-VHS VCR
only
2.
or
the S-VIDEO
Insert
a
video
PLAY button
(See
can
simultaneously,
be received.
tape into the VCR and press the
on
the VCR.
VCR owner's
manual)
or
<VCR>
Owner's Manual
9
Installation
External
Watching Cable
<
Back
panel
of the set
Equipment
V
iewing
Viewing
Setups
Setups
TV
>
-
After
subscribing
converter you
-
for
can
a
local cable TV station and
installing
a
watch cable TV.
For further information of cable
TV,
contact the local cable TV
station.
To watch cable TV
1.
Use the INPUT button
on
the remote control to select AV 1
AV2, S-Video2, AV3, AV4
-
or
,
AV5.
If both S-VIDEO and VIDEO sockets have been connected
to the Cable box
simultaneously, only
the S-VIDEO
can
be
received.
or
2.
Select your desired channel with the remote control for
cable box.
or
<
Watching
Cable box
>
DVD
How to connect
1. Connect the DVD video
(Y, PB, PR) INPUT jacks on the set and connect the DVD
audio outputs to the AUDIO INPUT jacks on the set, as shown in the figure.
If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the set and connect the DVD audio outputs
to the AUDIO INPUT jacks on the set, as shown in the figure.
Note: If your DVD player does not have component video output, use S-Video.
2.
outputs (Y, PB, PR)
to the COMPONENT
<
How to use
1.
Turn
2.
Use
3.
Component, AV1, AV2 or AV3.
(If connected to S-VIDEO, select the AV4 or AV5
input source.)
Refer to the DVD player's manual for operating
on
the DVD
INPUT
player,
button
on
and insert
the
a
DVD.
remote
control
to
select
external
instructions.
?
Component Input ports
You can get better picture quality if you
DVD player with component input ports as
Component ports
of the
set
Video
output ports
of DVD
player
connect
below.
YPBPR
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
or
<
10
PLASMA TV
DVD
player
>
Back
panel
of the set
>
Installation
Watching
<
Back
panel
external AV
of the set
source
>
-
When
connecting
the set to
external source,
an
match the
colours of AUDIO/VIDEO
jacks
=
on
input jacks on the set with the output
equipment: Video yellow, Audio (Left)
the audio/video
white, Audio (Right)
=
=
red.
How to use
1. Use the INPUT button
on
the remote control to select
AV1, AV2, S-Video2, AV3, AV4
2.
AV5.
the
corresponding external equipment.
external equipment operating guide.
Operate
See
or
Camcorder
AUDIO
RL
VIDEO
Video game set
-
Watching
DTV with
This set
receive
signals
can
from
a
Set-top
Digital
box
Free to air/Cable
digital set-top
box
or
other
signals without an external digital set-top box. However,
digital external device, refer to the figure as shown below.
if you do receive
Digital
How to connect
1. Use the set's COMPONENT
RGB
HDMI INPUT
(Y, PB, PR),
jack for video connections, depending on your set-top box
nector. Then, make the corresponding audio connections.
How to
1. Turn
the
or
?
Input signal
con-
the
digital set-top
digital set-top box.)
2. Use INPUT
on
box.
(Refer
Component,
RGB
box
RGB
HDMI
480i / 576i
o
x
x
/
o
o
o
720p (50/60Hz)
o
o
o
1080i
o
o
o
480p
or
Digital Set-top
Component
to the owner's manual for
the remote control to select
Terminal
Mode
use
on
from
576p
(50/60Hz)
HDMI.
<
or
HDMI OUTPUT
Back
panel
of the set
>
or
(R)
AUDIO
DVI OUTPUT
(L)
<
Digital Set-top
(R)
Box
AUDIO
(L)
Y
PBR
P
>
Owner's Manual
11
Installation
External
Digital
<
Back
Audio
panel
Equipment
V
iewing
Viewing
Setups
Setups
Output
of the set
>
Send the set's audio to external audio
-
Digital
Audio
Output (Optical) port.
not look into the optical output port. Looking
Caution: Do
may
equipment (stereo system)
damage
via the
at the laser beam
your vision.
How to connect
1. Connect
one
end of
an
optical
cable to the TV
Digital
Audio
(Optical)
Output port.
2. Connect the other end of the
input
on
3. Set the
See the
Monitor Out
"
optical cable to the digital audio (Optical)
the audio equipment.
TV speaker option Off" in the AUDIO menu. Refer to page 28.
external audio equipment instruction manual for operation.
-
Setup
<
-
The set has
a
second TV
a
special signal output capability
or
Back
which allows you to hook up
monitor.
Connect the second TV
or
monitor to the set's EURO SCART SOCKET.
See the
Operating Manual of the second
regarding that device's input settings.
Input
Mode
TV
or
Output
monitor for further details
Mode
SCART 1
AV1 CVBS/RGB
TV CVBS
SCART 2
AV2 CVBS,
S-Video2 Y/C
DTV CVBS
SCART 3
AV3 CVBS
Monitor out
Note:
a.
b.
Component, RGB, HDMI input
HDMI input sources cannot be
sources
cannot be used for Monitor out.
used for DTV out.
S-VIDEO
IN
(R)
12
PLASMA TV
AUDIO
(L)
VIDEO
panel
of the set
>
Installation
Connecting PC
-
-
-
-
To
enjoy vivid picture and sound, connect a PC to the set.
Avoid keeping a fixed image on the set's screen for a long period
on the screen; use a screen saver when possible.
Connect PC to the RGB INPUT
There
might
into another
picture
or
of time. The fixed
image
may become
permanently imprinted
HDMI/DVI INPUT
port of the set; change the resolution output of PC accordingly.
resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode
be noise
according to some
resolution or change the refresh
is clean. If the refresh rate of the PC
graphic
card
can
or
not be
adjust the brightness and contrast on
changed, change the PC graphic card
the
or
menu
until the
consult it to the
manufacturer of the PC
-
The
graphic card.
synchronization input waveform for
rate into another rate
Horizontal and Vertical
frequencies
are
separate.
Instructions to Connect a PC to your set
We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
If the resolution of PC is over XGA, there will be no picture on the set.
Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set
HDMI or DVI output port of the PC to the HDMI/DVI INPUT port on the set.
Setup
-
-
-
-
-
-
-
-
-
-
-
or
the
signal
cable from the
Connect the audio cable from the PC to the Audio
input on the set. (Audio cables are not included with the set).
If using a sound card, adjust PC sound as required.
This set uses a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC
adjusts automatically to use this set.
DDC protocol is preset for HDMI (Digital RGB) mode.
If required, adjust the settings for Plug and Play functionally.
If graphics card on the PC does not output analog and digital RGB simultaneously, connect only one of RGB INPUT or HDMI
INPUT to display the PC on the set.
If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or HDMI; (the other
mode is set to Plug and Play automatically by the set.)
DOS mode may not work depending on video card if you use a HDMI to DVI cable.
When you use too long RGB-PC cable, there might be noise on the screen. We recommend using under 5m of the cable. It
provides the best picture quality.
PC
Setup
<
1. Turn
on
the PC and
apply power to the set.
display by pressing the POWER
2. Turn
on
the
button
Back
panel
of the set
>
on
the set's remote control.
3. Use the INPUT button
the RGB
or
HDMI
4. Set the resolution
(Refer
to p.
input
on
the remote control to select
source.
output of the PC
to 1024
x768, 60Hz.
14)
Owner's Manual
13
Installation
Displayable
Monitor
RGB / HDMI mode
Resolution
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
35.000
66.66
37.861
72.80
37.500
75.00
43.269
85.00
31.500
60.00
37.799
70.00
39.375
75.00
31.500
60.00
37.799
70.00
39.375
75.00
35.156
56.25
37.879
60.31
48.077
72.18
46.875
75.00
53.674
85.06
49.725
74.55
48.363
60.00
56.476
70.06
60.023
75.02
68.677
85.00
54.348
60.05
63.995
70.01
67.500
75.00
68.681
75.06
60.023
60.02
63.981
60.02
640x350
720x400
640x480
848x480
852x480
800x600
832x624
1024x768
1152x864
1152x870
1280x960
1280x1024
14
PLASMA TV
Specification
Specification
Installation
-
HDMITM, the HDMI logo and High-Definition Multimedia Interface
are
trademarks
or
registered
trademarks of HDMI
Licensing.
-
-
-
-
This set
receive the
High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI).
This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play,
sets the HDMI/DVI source devices automatically.
After reading HDMI/DVI source devices, using Display Data Channel (DDC) Protocol, Extended Display Identification
Data (EDID) stored in the set is used.
If HDMI/DVI Source devices do not support AUTO HDMI/DVI, the resolution is set manually.
When Source Devices have DVI Output Connector, you must connect audio with separated cable.
(Refer to <How to connect>)
can
this
How to connect
1. When Source Devices
-
If Source Devices
the
-
-
-
(DVD Player or Set Top Box) support HDMI.
have HDMI Output Connector, Source Devices connect
to the set with HDMI Cable
.(not supplied
with
product).
If Source Devices
support Auto HDMI, automatically, Source Devices divert output resolution in 640x480p. But if not, refer
to the reference Manual of Source Devices and select resolution
manually.
To
Box
get the best picture quality, adjust the DVD Player
Because HDMI sends
Digital
Video and Audio with
or
one
Set
Top
output resolution
cable, there is
no
need for
a
to
640x480p.
special Audio Cable
when
using
a
HDMI Cable.
2. When Source Devices
-
If Source Devices
with the
-
-
-
to the set with HDMI to DVI Cable
(not supplied
product).
If Source Devices
support Auto DVI, automatically, Source Devices divert output resolution in 640x480p. But if not, refer
to the reference Manual of Source Devices and select resolution
manually.
To
Box
get the best picture quality, adjust the DVD Player
In this case,
Input
use
If PC has
or
Set
Top
output resolution
another cable for audio. When Source Devices have
of the set connect to Audio Cable
3. When PC
-
(DVD Player or Set Top Box) supports DVI.
have DVI Output Connector, Source Devices connect
(not supplied
with the
product).
Analog
Audio
And then you
to
640x480p.
Output Connector,
can
RGB/DVI Audio
listen to normal Audio.
supports DVI.
a
DVI
Output Connector,
Source Devices connect to the set with HDMI to DVI Cable
(not supplied
with the
product).
-
-
-
To
get the best picture quality, adjust the PC graphics card to 640x480, 60Hz.
Use the the set's HDMI/DVI (VIDEO) for video connections, depending on your PC connector.
If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only
Input
-
-
-
or
HDMI/DVI
Input
to
display
the PC
on
one
of either RGB
the set.
If the
graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI
Input; (the other mode is set to Plug and Play automatically by the set.)
Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
In this case, use another cable for audio. When PC (or sound card of PC) have Analog Audio Output Connector,
RGB/DVI Audio Input of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to
normal Audio.
Owner's Manual
15
Installation
Reference
Cable
sample
HDMI Cable
(not supplied
with the
Analog
product)
How to
with the
3.
4.
product)
Analog Audio Cable (Stereo to RCA type)
(not supplied with the product)
product)
use
1. Connect the HDMI/DVI Source
2. Turn
(RCA type)
with the
(not supplied
HDMI to DVI Cable
(not supplied
Audio Cable
Devices(DVD Player
or
Set
Top
Box
or
PC)
and the set.
display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.
Select HDMI/DVI Input source in Main Input option of PIP/DW menu.
Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness
in HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the
refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC
graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.
on
the
Notes:
-
-
-
-
Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.
Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently
imprinted on the screen. Use the Orbiter screen saver when possible.
When Source Devices are connected with HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size
may not fit to Screen. As shown on page 34, press the MENU button to adjust the screen Position of the set and contact
a PC graphics card service centre.
When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit
EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service
centre.
-
In
And in
display
16
HDMI/DVI Source Devices Cable is not connected
case
case
of Video Resolution not
being supported by
poor cable connection, "No Signal" OSD display will appear.
the set output in HDMI/DVI Source Devices, "No Signal" OSD
or
will appear. Refer to the Manual of HDMI/DVI Source Devices
PLASMA TV
or
contact your service centre.
Installation
Accessories
TVAV
MULTIMEDA
POWER
DVD
VCR
TV
MODE
CABLE
STB
AUDIO
ZOOM
PIP
-
ZOOM
MUTE
I
L ST
SLEEP
TEXT/
+
*
I/II
ARC
MENU
EXIT
OK
PIP
PR
-
VOL
PIPPR
+
SSM
SWAP
PSM
FAVOURITE
NPUT
PIPI
PR
Q.VIEW
SIZE
POSITION
INDEX
HOLD
TIME
REVEAL
MIX
MODE
?
M
LG TV
ASmark
Remote Control handset
Owner's Manual
2-Eye
Bolts
1.5V
1.5V
Power Cord
Alkaline batteries
Joining
-
the set
Secure the set
assembly
to the wall to
assembly by joining
it to
a
prevent the
wall
by using
the
2-Wall brackets
set
tumbling
Eye
Bolts/Wall brackets.
If the set is to be mounted on a desk top, insert the 2
securely in the upper holes as shown.
?
Eye-Bolts
and
tighten
them
Install the wall brackets on the wall with 2 bolts*, (not supplied with the product),
as shown.
Match the height of the Eye-Bolts and the wall brackets.
Check to be sure the Eye-Bolts and the brackets are tightened securely.
Secure the set
assembly to the
(not supplied with the product),
?
Optional
-
wall with
as
strong strings
or
wound wire
cables,
shown.
Extras
Optional
extras
can
be
changed
or
modified for
quality improvement.
Without any
notification,
new
optional
extras
can
be
added.
-
Contract your dealer for the
purchasing
of these items.
42
40
40
5
0
Tilt wall
mounting
bracket
42
Ceiling mounting
bracket
Video cables
Audio cables
Owner's Manual
17
Installation
Installation
?
The set
Options
Options
be installed in different ways such as on a wall, or on a desktop etc.
Install this set only in a location where adequate ventilation is available.
?
can
Wall Mount: Horizontal Installation
?
The set
can
be installed
on a
(For further information, refer
Mounting Bracket Installation
To Mount
on a
wall
as
Desktop
shown above.
The set
can
be mounted
on a
desk
as
shown above.
optional 'Wall
Setup Guide'.)
to the
and
Wall
To Install
on a
Desktop
Wall mount minimum allowable clearances for ade-
Pedestal mount minimum allowable clearances for
quate ventilation.
adequate
10cm
3cm
10cm
10cm
10cm
18
?
Pedestal Installation
PLASMA TV
ventilation.
Operation
T
urning
Turning
-
When
using
Turning
the remote
the set
on
just
1. Connect power cord
2.Pressthe
buttons
the Set
Set
on
on
control, aim it
at its
the set.
sensor on
after installation
correctly,
the set is switched to
standby
mode.
/I,INPUTorPRD /EbuttononthesetorpressthePOWER,INPUT,D/ATV,PRD /EorNUMBER
on
the remote control and then the set will switch
on.
Initializing setup
setup
If the OSD
Willkommen
Vergewissern
turning
on
(On
Screen
the set, you
Display) is displayed on the screen as figure
can adjust the Auto Programme tuning.
after
Sie sich,
daß eine Antenne
angeschlossen
ist.
Note: It will
OK
button is
Turning
on
the set
(power
cord is still
automatically disappear after approx.
pressed.
Pressthe
button
on
The
/ I button
on
the set
/I,INPUTorPRD/EbuttononthesetorpressthePOWER,INPUT,D/ATV,PRD/EorNUMBER
the remote control to turn the set
On-Screen
On-Screen Menu
-
a
connected)
If the set was turned off with the remote control power button and the
?
40 seconds unless
menus can
be shown
on
the
screen
1. Press the MENU button and then
2. Press the G button and then
use D
3. Press the G button and then
use D
From this
point
on, the
on-screen
on.
Language
in the selected
use D
language.
Selection
Selection
First select your
/ E button to select the SPECIAL
/ E button to select Menu
(option)
(option)
language.
menu.
language.
/ E button to select your desired language.
menus will be shown in the language of your choice.
4. Press the EXIT button to return to normal TV
viewing.
Owner's Manual
19
Operation
Channel
Channel Menu
Auto
-
Options
Options
Programme Tuning (In Digital mode)
Use this Auto
Programme
to
automatically
1. Press the MENU button and then D
2. Press the G button and then D
/ E
find and store all of the programmes.
button to select the STATION
/ E
menu.
button to select Auto programme.
3. Press the G button to select Start.
4. Press the G button to
All receivable stations
begin
are
auto
programming.
stored.
PICTURE
Programme
SOUND
5V antenna power
System information
stop
programming, press the MENU button.
When auto programming is completed, the Programme edit
Note
a.
menu
on
appears
c.
-
Prev.
the
'Programme
Auto programme
0
When you start auto
be deleted.
begin
auto
programming
programming
or
in
digital mode,
manual
all the stored service information will
programming, input
system. Be sure to remember this number!
If you forgot your password, press '7', '7', '7', '7'
Auto
Menu
:
b. To
edit
SCREEN
Edit' section to edit the stored programme.
5. Press the EXIT button to return to normal TV viewing.
screen.
Start
G
SPECIAL
PIP/DW
auto
See the
Auto programme
Manual programme
TIME
The message "All of service-information will be updated. Continue?" will appear.
If you want to keep on auto programming select YES. Otherwise select NO.
To
STATION
a
VHF CH.
11
10
%
in Lock
4-digit password
Menu
on
Pro.
Stop
the remote control handset.
Programme Tuning (In Analogue mode)
All stations that
can
be received
are
stored
by
this method. It is recommended that you
use
auto programme
during
installation of this set.
1. Press the MENU button and then
2. Press the
G
/ E button to select the STATION
menu.
STATION
:
BG
:
I
4.
SECAM L/L'
PAL
/ E
TIME
Note
a.
In
begin
are
auto
PIP/DW
number
programming.
stored.
:
some
models, the station
name
is stored for stations which broadcast VPS
(Video
Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as
C (V/UHF 01-69) or S (Cable 01-47), followed by a number.
b. In Australia, if no station name can be assigned to a station, the channel number is
followed by a number see 'Assigning a station name' secassigned and stored as
tion to assign the station name.
-----
To
programming, press the MENU button.
When auto programming is completed, the Programme edit menu appears
screen. See the 'Programme edit' section to edit the stored programme.
20
stop
auto
PLASMA TV
SPECIAL
SCREEN
5. Press the E button to select Start.
All receivable stations
Programme
SOUND
/ Ireland /
6. Press the G button to
G
edit
Favourite programme
(option)
Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
Press the E button to select Storage from. Select the beginning programme
with the F / G button or NUMBER buttons on the Storage from menu.
:
PICTURE
B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
PAL I/II (U.K.
Auto programme
Manual programme
button to select Auto programme.
3. Press the G button to select System. Select a TV system with the F / G button;
L
button and then D
use D
on
the
Menu
Prev.
System
Storage from
Start
BG
2
Operation
Manual
-
Programme Tuning (In Digital mode)
Manual programme lets you
manually
add
1. Press the MENU button and then D
2. Press the
G
button and then
button to select the STATION
/ E
menu.
STATION
button to select Manual programme.
E button to select the desired channel number.
D / E
3. Press the G button and then D
4. Press the OK button to
programme to your programme list.
a
/
5. Press the EXIT button to return to normal TV
edit
PICTURE
Programme
SOUND
5V antenna power
System information
this channel to your
channel list.
using
the F
35
TIME
SPECIAL
SCREEN
/ G
PIP/DW
Menu
Prev.
viewing.
Programme Tuning (In Analogue mode)
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you
assign a station name with five characters to each programme number.
1. Press the MENU button and then
2. Press the
G
button and then D
3. Press the G button to select
/ G
Your receiver will add
UHF CH.
appear. If you want to keep on manual programming, select YES with
button. Then, press the OK button. Otherwise select NO.
-
G
save.
When the channel number you want to add is already added in programme list, the
massage "Service-information of the channel will be updated. Continue?" will
Manual
Auto programme
Manual programme
button
or
4. Press the E button to select
:
SECAM L/L'
BG
:
PAL
I
:
DK
:
M
:
B/G,
on
the
System.
menu.
STATION
PICTURE
Select the desired programme number with the F
Storage.
NUMBER buttons
L
/
/ E button to select the STATION
E button to select Manual programme.
use D
Storage
Select
a
/Australia)
PAL I/II (U.K.
(Europe
/ East
/ Ireland /
TV
Europe
/ South
Hong Kong
PAL D/K, SECAM D/K (East Europe
(USA / Korea / Philippines) (option)
Auto programme
Manual programme
Programme
edit
Favourite programme
System
BG
Band
V/UHF
Channel
system
with the F
/ G
button;
/ Asia / New Zealand / M.East / Africa
TIME
Fine
SPECIAL
Search
/ China / Africa /
1
Name
SCREEN
Africa)
/ G
2
SOUND
PIP/DW
5. Press the E button to select Band. Press the F
Storage
G
menu.
(option)
SECAM B/G
can
C01
Menu
Prev.
CIS)
button to select V/UHF
or
Cable
as
required.
6. Press the E button to select Channel. You
the F
/ G
button
or
NUMBER buttons. If
select the desired channel number with
can
possible,
select the channel number
directly
with
the number buttons.
7. Press the E button to select Search. Press the F
a
station is found the search will
/ G
button to
commence
searching.
If
stop.
8. Press the OK button to store it.
9. To store another
Fine
-
station, repeat steps
Tuning (In Analogue
Normally
fine
tuning
is
only
mode
3 to 8.
only)
necessary if
reception
is poor.
the 'Manual programme tuning' steps 1 to 2.
2. Press the G button and then D / E button to select Fine.
1.
Repeat
STATION
PICTURE
3. Press the F
/ G
button to fine tune for the best
picture
and sound.
The
finely
SOUND
selection.
TIME
viewing.
tuned programme will be indicated
by yellow
number
Programme
edit
Favourite programme
4. Press the OK button.
5. Press the EXIT button to return to normal TV
Auto programme
Manual programme
during
programme
SPECIAL
Storage
2
System
BG
Band
V/UHF
1
Channel
Fine
Search
Name
C01
SCREEN
PIP/DW
Store
Owner's Manual
21
Operation
Channel
Channel Menu
Assigning
Station Name
a
(In Analogue
Options
Options
mode
only)
the 'Manual programme tuning' steps 1 to 2.
2. Press the G button and then D / E button to select Name.
1.
Repeat
3. Press the
G
button to
display
4. Press the D button. You
the Name
can use a
blank,
STATION
PICTURE
menu.
+,
-,
the
alphabet
A to Z and the numeric 0 to
SOUND
SPECIAL
sec-
7. Press the EXIT button to return to normal TV
Programme
Edit
(In Digital mode)
programme number is skipped, it means that you will be unable to select it using PR D / E button during
TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER
buttons or select it in the Programme edit menu.
This function enables you to
1. Press the MENU
the stored programmes.
skip
button, then
use
2. Press the G button and then D
/ E
the D
button to select the STATION
/ E
button to select
Programme
edit
menu.
menu.
3. Press the G button to enter the
4.
5.
6.
Programme edit menu.
Select a programme to be stored or skipped with the D / E or F / G button.
Press the BLUE button repeatedly to have the programme skipped or stored.
In case of programmes to be skipped, skipped programme shows in gray colour and
these programmes will not be selected by the PR D / E buttons during TV viewing.
Press the EXIT button to return to normal TV viewing.
Skipping
a
1. Select
2.
3.
programme number
programme number to be
skipped with the D / E or F / G button.
Press the BLUE button. The skipped programme number turns to gray.
Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be unable to select it
using the PR D / E button during normal TV viewing. If you want to select the skipped
programme, directly enter the programme number with the NUMBER buttons or select
a
it in the programme edit or EPG.
4. Press the EXIT button to return to normal TV
viewing.
programme (In Lock System On mode only)
1. Select a programme to be locked with the D / E or F / G button.
2. Press the GREEN button. The lock mark will appear in front of that programme number.
Locking
a
Press the GREEN button
again
to release this function.
Note :
a. To watch a locked programme, input a 4-digit password in Lock system. Be sure to
remember this number!
b. If you forgot your password, press '7', '7', '7', '7' on the remote control handset.
c. If you select other programme after releasing a locked programme and then return to
the locked programme within 1 minute, you needn't input a password to select the
locked programme.
Moving
a
programme
1. Select a programme to be moved with the
D / E
or F / G
button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with the D
4. Press the YELLOW button again to release this function.
favourite programme
Select your favourite programme number
/ E
or F / G
button.
Selecting
by pressing
D / E
or F / G
button and then
press the FAV button on your remote control handset. It will automatically include the
selected programme into your favourite programme list and heart-mark will appear in
front of that programme number.
22
PLASMA TV
2
System
BG
Band
Channel
V/UHF
1
Fine
Search
C01
SCREEN
viewing.
a
Storage
Name
PIP/DW
6. Press the OK button in twice.
-
edit
TIME
With the E button you can select in the opposite direction.
5. Select the next position by pressing the G button and then take your choice of the
ond character, and so on.
When
Programme
Favourite programme
9.
-
Auto programme
Manual programme
Prev.
Operation
Programme
Edit
(In Analogue mode)
1. Press the MENU
button, then
2. Press the G button and then D
Deleting
1. Select
a
button to select the STATION
/ E
button to select
/ E
3. Press the G button to enter the
a
the D
use
Programme
programme
programme to be deleted with the
edit
D / E
Programme
menu.
edit.
0-
menu.
button.
or F / G
deleted, all the following programmes
are
shifted up
one
-
-
-
5C05
-
1BLN2
6C07
2C01
7C55
3C04
8S27
4C05
9S29
2. Press the RED button twice.
The selected programme is
edit
Programme
Delete
Copy
Move
Skip
Menu
Prev.
position.
Copying
a
1. Select
a
programme
programme to be
with the D
copied
/ E
or F / G
button.
2. Press the GREEN button.
All the
Moving
following
programmes
shifted down
are
one
position.
a
programme
1. Select a programme to be moved with the
D / E
or F / G
button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with the D
4. Press the YELLOW button again to release this function.
Skipping
a
1. Select
a
programme number
programme number to be
skipped with the D / E
skipped programme number
2. Press the BLUE button. The
or F / G
/ E
or F / G
button.
button.
turns to blue.
3. Press the OK button.
4. Press the OK button then
use
the BLUE button to release the
skipped
programme.
When a programme number is skipped it means that you will be unable to select it using
the PR D / E button during normal TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in
the programme edit or table menu.
5. Press the EXIT button to return to normal TV
5V antenna power
-
Even if there isn't
a
(In Digital
special
5V
mode
adapter
1. Press the MENU button and then
viewing.
only)
power in the external antenna, this function
/ E button to select the STATION
use D
can
output 5V in the
menu.
STATION
set.
Auto programme
Manual programme
2. Press the G button and then
button to select 5V antenna power.
use D / E
PICTURE
5V antenna power
SOUND
3. Press the G button and then
use D / E
button to select On
or
Programme edit
System
information
G
On
Off
Off.
TIME
In 5V antenna power On, if the set is short-circuit, it will automatically return to Off.
The message "Antenna feed overloaded. Automatically switched off." will
SCREEN
appear.
4. Press the EXIT button to return to normal TV
System
-
If
information
signal strength
SPECIAL
is
mode
(In Digital
2. Press the G button and then D
Model name, Software
use D
viewing.
Menu
Prev.
only)
weak, check the RF cable
1. Press the MENU button and then
PIP/DW
or
antenna.
/ E button to select the STATION
menu.
System information menu.
version, Signal strength and Signal quality are displayed.
/ E
button to select
3. Press the EXIT button to return to normal TV
viewing.
Owner's Manual
23
Operation
Channel
Channel Menu
Favourite
Programme (In Analogue mode)
1. Press the MENU button and then
2.
3.
4.
5.
6.
7.
8,
/ E button to select the STATION menu.
Press the G button and then D / E button to select Favourite programme.
Press the G button to display the Favourite programme menu.
Press the D / E button to select
-----.
Select a desired programme with the F / G button or NUMBER buttons. Any number
under 10 is entered with a numeric '0' in front of it, i.e. '05' for 5.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
Press the OK button.
Press the EXIT button to return to normal TV viewing.
use D
--
Repeatedly
Calling
-
Options
Options
You
Auto programme
Manual programme
PICTURE
Programme
edit
Favourite programme
SOUND
TIME
SCREEN
PIP/DW
Menu
Prev.
Programme Table (In Digital mode)
check the programmes stored in the memory
Displaying programme
table
Press the LIST button to
display
The programme table appears
the
on
Programme
the
table
by displaying
the programme table.
menu.
screen.
Status
Display
Favourite
Locked
Selecting
Select
a
Programme
Programme
programme in the programme table
programme with the D
Then press the OK button.
a
/ E
button.
The set switches to the chosen programme number.
favourite programme table
Press the FAV button to display the Favourite
Displaying
Calling
up the
Programme
table
Press the LIST button to display the Programme table
The programme table appears on the screen.
?
menu.
Programme Table (In Analogue mode)
Displaying programme
?
table
menu.
You may find some blue highlighted programmes shown. They have been set up in the
programme edit mode.
Some programmes with the channel number shown in the programme table indicate
there is no station name assigned.
Selecting
a
programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The set switches to the chosen programme number.
Paging through
There
a
programme table
10 programme table pages in which contain 100 programmes.
the D / E or F / G button repeatedly turns the pages.
are
Pressing
Press the LIST button to return to normal TV
24
PLASMA TV
viewing.
FG
0BLN2
---
--
---
---
--
---
---
--
---
---
--
---
---
--
---
---
--
---
---
--
---
SPECIAL
press the FAV button to select stored favourite programmes.
up the
can
STATION
0-
-
-
-
-
5C05
1BLN2
6C07
2C01
7C55
3C04
8S27
4C05
9S29
Operation
Picture Menu
PSM
-
-
Options
Options
(Picture Status Memory)
This function
adjusts the set to the best picture appearance.
When adjusting picture options (contrast, brightness, colour, sharpness
is automatically changed to User.
and tint
(NTSC input only)) manually,
PSM
1. Press the PSM button
?
Each press of the PSM button
?
?
You
display
shown below.
as
Standard
Mild
User
Intelligent Eye, Dynamic, Standard, Mild or User in the PICTURE menu.
Picture options Intelligent Eye, Dynamic, Standard and Mild are preset and programmed for good picture
quality at the factory and cannot be changed.
When Intelligent Eye function is On, the most suitable picture is automatically adjusted according to the surrounding conditions.
CSM
-
screen
Dynamic
Intelligent Eye
?
the
changes
can
also select
(Color Status Memory)
To initialize values
(reset
to default
settings),
1. Press the MENU button and then
select the Normal
use D / E
option.
button to select the PICTURE
menu.
STATION
PSM
CSM
2. Press the G button and then
PICTURE
button to select CSM.
use D / E
button to select the desired colour
use D / E
tempera-
TIME
ture.
Normal
Contrast
Warm
100
Brightness
60
Colour
50
Sharpness
50
User
SPECIAL
4. Press the EXIT button to return to normal TV
?
Each press of D / E button
Cool
You
can
the
viewing.
screen
Normal
Manual Colour
-
changes
display
SCREEN
as
shown below.
Warm
PIP/DW
Menu
adjust red,
green,
or
blue to any colour
2. Press the G button and then
3. Press the G button and then
4. Press the G button and then
use D / E
use D / E
button to select the PICTURE
menu.
STATION
0
use D / E
use F / G
button to select User.
button to make
G
Cool
Normal
ACM
appropriate adjustments.
viewing.
Contrast
Warm
100
Brightness
60
Colour
50
Sharpness
50
User
Red
0
SPECIAL
Green
0
SCREEN
Blue
0
PIP/DW
-
Blue
PSM
PICTURE
button to select CSM.
5. Press the EXIT button to return to normal TV
-
0
temperature you prefer.
TIME
Menu
picture with LG's excellent Digital Reality processor technology.
This function is not available for use in RGB[PC], HDMI[PC] mode.
When selecting picture options (Intelligent Eye, Dynamic, Standard and Mild) in PICTURE menu, XD
ically changed to On.
enjoy
Green
User
SOUND
can
0
Prev.
CSM
You
Red
Temperature Control
1. Press the MENU button and then
-
Cool
ACM
SOUND
3. Press the G button and then
G
Prev.
the vivid and hi-definition
1. Press the MENU button and then
use D / E
button to select the PICTURE
menu.
STATION
is automat-
PSM
CSM
2. Press the G button and then
use D / E
button to select XD.
use D / E
button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
viewing.
On
Off
ACM
SOUND
3. Press the G button and then
G
PICTURE
Contrast
100
Brightness
60
Colour
50
Sharpness
50
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
25
Operation
Picture Menu
sRGB
-
(RGB[PC], HDMI[PC]
mode
When the set is connected to external
equal image
-
Options
Options
only)
equipment
with the sRGB
function, the colour difference is adjusted the
of each other.
This function works in the
following
1. Press the MENU button and then
mode
:
RGB[PC], HDMI[PC].
button to select the PICTURE
use D / E
menu.
STATION
PSM
CSM
2. Press the G button and then
use D / E
PICTURE
button to select sRGB.
sRGB
SOUND
3. Press the G button and then
use D / E
button to select On
or
Off.
G
Contrast
On
Off
100
60
Brightness
TIME
4. Press the EXIT button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
ACM
-
-
Menu
Prev.
(Active Color Management)
Adjust
the ACM to select the desired skin colour
This function is not available for
-I t 's not available to
use
use
in
option.
RGB[PC], HDMI[PC]
mode.
this function in XD Off mode.
1. Press the MENU button and then
button to select the PICTURE
use D / E
menu.
STATION
PSM
CSM
2. Press the G button and then
3. Press the G button and then
use D / E
use F / G
PICTURE
button to select ACM.
button to make
ACM
appropriate adjustments.
SOUND
TIME
4. Press the EXIT button to return to normal TV
viewing.
G
Contrast
100
Brightness
60
Colour
50
Sharpness
50
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Manual Picture Control
adjust picture contrast, brightness, colour, sharpness and tint (NTSC input only)
-I t 's not available to use colour, sharpness function in RGB[PC], HDMI[PC] mode.
In the broadcasting system PAL/SECAM, the picture item Tint doesn't work.
-
You
can
to the levels you
prefer.
-
1. Press the MENU button and then
button to select the PICTURE
use D / E
menu.
STATION
PSM
CSM
2. Press the G button and then
3. Press the G button and then
use D / E
use F / G
button to select the desired
button to make
picture option.
PICTURE
ACM
SOUND
appropriate adjustments.
TIME
4. Press the EXIT button to return to normal TV
viewing.
Contrast
Brightness
60
Colour
50
Sharpness
50
SPECIAL
SCREEN
PIP/DW
26
PLASMA TV
100
Menu
Prev.
G
Fleshtone
0
Greentone
0
Bluetone
0
Operation
Sound
Sound Menu
SSM
-
-
Options
Options
(Sound Status Memory)
This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the SSM button.
2. Press the SSM button to select your desired sound.
SRS TSXT
?
?
You
Flat
Music
Movie
User
Sports
also select SRS TSXT, Flat, Music, Movie, Sports or User in the SOUND menu.
The sound SRS TSXT, Flat, Music, Movie and Sports are programmed for good sound reproduction at the
can
cannot be
factory
and
changed.
R
-
ruSurround XT
-
is
a
trademark of SRS
TruSurround XT
technology
is
Labs, Inc.
incorporated
under license from SRS
Labs, Inc.
BBE
-
BBE
High
Definition Sound restores
1. Press the MENU button and then
clarity
and presence for better
speech intelligibility
button to select the SOUND
use D / E
menu.
and musical realism.
STATION
SSM
BBE
2. Press the G button and then
use D / E
PICTURE
button to select BBE.
use D / E
button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
viewing.
SPECIAL
On
Off
AVL
Balance
SOUND
3. Press the G button and then
G
0
Treble
50
Bass
50
TV
Speaker
Digital audio out
Audio language
SCREEN
Manufactured under license from BBE
AVL
-
(Auto
Volume
Sound, Inc.
PIP/DW
Menu
Prev.
Leveler)
This feature maintains
an
equal
volume
1. Press the MENU button and then
level;
even
if you
change
channels.
button to select the SOUND
use D / E
menu.
STATION
SSM
BBE
2. Press the
G
button and then
use D / E
PICTURE
button to select AVL.
use D / E
button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
G
Balance
SOUND
3. Press the G button and then
AVL
viewing.
SPECIAL
0
Treble
50
Bass
50
On
Off
TV
Speaker
Digital audio out
Audio language
SCREEN
PIP/DW
Menu
Prev.
Adjusting Sound Control
1. Press the MENU button and then
button to select the SOUND
use D / E
menu.
STATION
SSM
BBE
2. Press the G button and then
use D / E
button to select the desired sound item.
PICTURE
Balance
SOUND
3. Press the G button and then
use F / G
button to make
4. Press the EXIT button to return to normal TV
appropriate adjustments.
viewing.
AVL
Treble
Bass
TIME
SPECIAL
0
50G
50
TV
Speaker
Digital audio out
Audio language
SCREEN
Note
:
Treble, Bass
or
BBE aren't suitable for
use
with SRS TSXT.
PIP/DW
Menu
Prev.
Owner's Manual
27
Operation
Sound
Sound Menu
TV
-
-
-
Options
Options
Speaker
You
the internal
speaker status.
In COMPONENT, RGB[PC] and HDMI[PC] mode,
there is no video signal.
can
adjust
If you want to
use
TV
speaker
and/or variable audio
your external hi-fi stereo system, turn off the internal
1. Press the MENU button and then
speakers
button to select the SOUND
use D / E
can
be
outputted
though
even
of the set.
menu.
STATION
SSM
BBE
2. Press the G button and then
use D / E
button to select TV
PICTURE
Speaker.
AVL
Balance
SOUND
3. Press the G button and then
use D / E
button to select On
or
50
Bass
50
Off.
Treble
TV
TIME
4. Press the EXIT button to return to normal TV
SPECIAL
GOn
Speaker
Digital
viewing.
0
Audio
Off
audio out
language
SCREEN
PIP/DW
Selecting Digital
-
-
-
-
Audio
Output (In Digital
mode
Menu
Prev.
only)
This function lets you select your preferred Digital Audio Output.
The set can output Dolby Digital in a channel only which broadcast
When it's
applied
the AC3
outputted
outputted
AC3. Even if it's
Dolby Digital Audio.
format, if you select Dolby digital on Digital audio out menu, SPDIF Output will
selected Dolby digital, when it doesn't apply AC3 format, SPDIF Output will be
be
PCM.
Even if both
Dolby digital and Audio language
only Dolby digital will be played.
1. Press the MENU button and then
have been set in
a
channel which broadcast
button to select the SOUND
use D / E
menu.
Dolby Digital Audio,
STATION
SSM
BBE
2. Press the G button and then
use D / E
3. Press the G button and then
use D / E
button to select
button to select
4. Press the EXIT button to return to normal TV
audio out
Digital
Dolby digital
Balance
SOUND
PCM.
or
AVL
PICTURE
menu.
Treble
50
Bass
50
TIME
viewing.
0
TV
Speaker
Digital audio out
Audio language
SPECIAL
Dolby digital
G
PCM
SCREEN
PIP/DW
Audio
-
-
-
Language (In Digital
mode
Menu
Prev.
only)
This function lets you select your preferred language for audio.
If the audio data in selected language is not broadcasted, default audio which is broadcasted in current channel will
be
played.
At
first, select PCM in Digital audio out
to
menu
play German, English, French, Spanish
or
Italian of Audio
language.
1. Press the MENU button and then
button to select the SOUND
use D / E
menu.
STATION
SSM
BBE
2. Press the G button and then
3. Press the G
Spanish
or
button and then
use D / E
use
button to select Audio
D / E button to select
language
AVL
PICTURE
menu.
Balance
Treble
50
German
Bass
50
English
SOUND
German, English, French,
TIME
Italian.
viewing.
Speaker
Digital audio out
Audio language
When two
or more
with the I/II button
-
-
audio
on
languages
button to select
an
Press the F
/ G
button to select
L+R, L+L
(On-screen
(On-screen Display)
Audio
Menu
can
Prev.
select audio
language
audio
language.
or
R+R.
Information
Status
Not Available
Notes: The audio which it has not
Audio
language
only
service
Audio for Visual
Audio for
PLASMA TV
broadcasted, you
/ E
N.A
Italian
G
the remote control.
Display
28
are
Press the D
OSD
OSD
Spanish
SCREEN
PIP/DW
-
French
TV
SPECIAL
4. Press the EXIT button to return to normal TV
0
Impaired
Hearing Impaired
character.
code will be
displayed
a
a
3
Operation
Stereo / Dual
-
When
programme is selected, the sound information for the station appears after the programme number and
a
station
Reception (In Analogue mode)
name
On Screen
disappear.
Display
Press the I/II button to received broadcast state.
Broadcast
On
Mono
MONO
Stereo
STEREO
Dual
DUAL I
screen
Display
Mono Sound Selection
In stereo
reception if the stereo signal is weak, you can switch to mono by pressing the
reception the depth of sound is improved. To switch back to stereo, press the I/II button
Language
If
programme
pressing the I/II
-
Language Broadcast
received in two languages (dual language),
button repeatedly.
?
DUAL I sends the
?
DUAL
?
DUAL
you
can
again.
switch to DUAL I, DUAL II
or
DUAL I
+
II
by
primary broadcast language to the loudspeakers.
II sends the secondary broadcast language to the loudspeakers.
I + II sends a separate language to each loudspeaker.
Reception (option) (In Analogue mode)
If your Plasma Display is equipped with the PDP Tuner for NICAM reception, the
Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound
twice
mono
Selection for Dual
a
NICAM
I/II button twice. In
output
can
be selected
according
to the
type of received broadcast
as
high quality
follows
NICAM
by pressing
(Near
the I/II button
repeatedly.
?
When NICAM
?
When NICAM stereo
switch to FM
?
mono
When NICAM dual is
Sound
In
is
weak,
select NICAM DUAL I, NICAM DUAL II, NICAM DUAL I
is selected the display MONO appears on the screen.
+
II,
received, you
mono
AV, Component, RGB
L+R
signal
stereo
can
or
Output Selection
Repeatedly
:
or
HDMI
mode, you
can
select
output sound for the left and right loudspeakers.
press the I/II button to select the sound output.
Audio
signal
right loud-speaker.
L+L : Audio signal
R+R : Audio signal
?
received, you can select NICAM MONO or FM MONO.
is received, you can select NICAM STEREO or FM MONO. If the
mono.
MONO. When FM
-
is
from audio L
?
from audio L
?
from audio
input
is sent to left
loud-speaker
and audio
signal
from audio R
input
is sent to
input is sent to left and right loud-speakers.
R input is sent to left and right loud-speakers.
Owner's Manual
29
Operation
ime Menu
Time
Options
Options
Current time
-
-
When you select 'Auto Clock On', the time is set automatically from
The digital channel signal includes information for the current time
broadcasting
digital channel signal.
provided by the
a
station.
STATION
GOn
Off
Manual Clock
PICTURE
Time
zone
Off time
SOUND
1. Press the MENU button and then
2. Press the G button and then
3. Press the G
Auto Clock
button and then
use D
use D
use D
/ E button to select the TIME
/
E
button to
adjust
menu.
sleep
Menu
Prev.
SPECIAL
SCREEN
the Year.
PIP/DW
use D
/
button to
adjust
the Date.
5. Press the G
use D
/ E button to
adjust
the Time.
E
Auto
TIME
/ E button to select the Manual clock
4. Press the G button and then
button and then
menu.
On time
STATION
Auto Clock
Manual Clock
6. Press the EXIT button to return to normal TV
viewing.
PICTURE
Time
G
zone
Off time
SOUND
2005
Year
On time
Auto
sleep
Menu
Prev.
Date
01
:
20
Time
16
:
11
TIME
SPECIAL
SCREEN
PIP/DW
Time Zone
Setup
1. Press the MENU button and then D / E button to select the TIME
menu.
STATION
Auto Clock
Manual Clock
2. Press the
G
button and then D /
E
button to select Time
PICTURE
zone.
Germany,
Great
/ E button to select your
Britain, France, Spain,
or
Italy.
zone
Off time
SOUND
3. Press the G button and then D
Time
viewing
area
time zone;
or F
Auto
sleep
Menu
Prev.
TIME
button.
SCREEN
5. Press the EXIT button to return to normal TV
30
PLASMA TV
viewing.
PIP/DW
Country
Germany
On time
SPECIAL
4. Press the OK
G
GMT +01:00
Operation
Setting
-
-
-
the On/Off Timer
The off timer
automatically
switches the set to
Off Timer function overrides
The set must be in
standby
standby
Timer function if
on
they
at the
are
preset time.
set to the
time.
same
mode for the On Timer to work.
1. Press the MENU button and then
use D
/ E button to select the TIME
menu.
STATION
Auto Clock
Manual Clock
2. Press the G button and then
3. Press the G button and then
use D
use D
/ E button to select Off time
or
On time.
PICTURE
Time
zone
Off time
SOUND
/ E button to select On.
GOn
On time
Auto
Off
sleep
TIME
4. Press the G button and then
use D
5. Press the G button and then
use D
6.
Only
On time
function;
gramme number
or
/ E button to
/
E
button to
-
To cancel
a
use D
/
E
on or
Pr.
SCREEN
button to
adjust
pro-
PIP/DW
Menu
TV
00
30
0
Prev.
volume level.
viewing.
time function
button has been
Once the
Auto
-
adjust
the minute.
:
Volume
SPECIAL
Press the D / E button to select Off in step 3.
Two hours after the set is switched on by the on time function it will
unless
-
Off/On
the hour.
Press the G button and then
7. Press the EXIT button to return to normal TV
-
adjust
00
automatically
switch back to
standby
mode
pressed.
off time is set, these functions
operate daily
at the
preset time.
Sleep
If there is
no
input signal,
the set turn off
1. Press the MENU button and then
automatically
use D
after 10 minutes.
/ E button to select the TIME
menu.
STATION
Auto Clock
Manual Clock
2. Press the G button and then
3. Press the G button and then
use D
use D
/ E button to select Auto
/ E button to select On
or
PICTURE
sleep.
Time
zone
Off time
SOUND
Off.
On time
Auto
sleep
GOn
Off
TIME
4. Press the EXIT button to return to normal TV
viewing.
SPECIAL
SCREEN
PIP/DW
Sleep
-
-
Sleep
Prev.
Timer
timer turns the set off at the
preset time.
Press the SLEEP button to select the number of minutes. The
lowed
Menu
by 10, 20, 30, 60, 90, 120,
180 and 240 minutes. The
display
timer begins
zz
Min will appear on the screen, folto count down from the number of minutes
---
selected.
remaining sleep time, press the SLEEP button once.
b. To cancel the sleep time, repeatedly press the SLEEP button until the display
c. If you turn the set off after setting the sleep timer, the setting will be erased.
a.
To check the
zz
---
Min appears.
Owner's Manual
31
Operation
Menu
Special
Special
Lock
System
Options
Options
Setting
1. Press the MENU button and then D / E button to select the SPECIAL
2. Press the G button and then D / E button to select Lock
menu.
STATION
system.
PICTURE
Menu
language
Lock
system
SOUND
Child lock
sure
-
-
-
-
-
-
-
Confirm
reset
-
SPECIAL
NUMBER buttons to
use
input
a
4-digit password.
SCREEN
to remember this number!
Re-enter
If you
New
Demo
Factory
Press the G button and then
Be
Set PIN
Low power
Set ID
TIME
password
Off
Lock
ISM method
3. Press the G button and then D / E button to select On.
To set the
G
new
forgot
password
your
PIP/DW
for confirm.
password,
press '7', '7', '7', '7'
4. Press the EXIT button to return to normal TV
on
Prev.
Menu
the remote control handset.
viewing.
Child Lock
-
The set
be set up
can
so
that it
only
can
be used with the remote control.
1. Press the MENU button and then D / E button to select the SPECIAL
menu.
STATION
Menu
Lock
language
2. Press the G button and then D / E button to select Child lock.
3. Press the G button and then D / E button to select On
or
PICTURE
system
Off
ISM method
SOUND
Off.
Low power
Set ID
TIME
4. Press the EXIT button to return to normal TV
GOn
Child lock
Demo
Factory
viewing.
reset
SPECIAL
SCREEN
PIP/DW
-
-
This set is
In Child
D/A
-
TV, PR
was
/
last set to
I, INPUT,
if you turn the set off.
PR D / E button on the set or
even
POWER, INPUT,
D / E or NUMBER buttons on the remote control.
With the Child lock On, the display
pressed while viewing the set.
ISM
-
programmed to remember which option it
lock 'On', if the set is turned off, press the
'
(Image Sticking Minimization)
A frozen of still
picture
image remaining even
a long period of time.
Child lock on' appears
on
the
screen
if any button
on
the front
panel
Method
button to select the SPECIAL
use D / E
menu.
STATION
Menu
Lock
2. Press the G button and then D
3. Press the G button and then D
or
/ E
/ E
button to select ISM Method.
PICTURE
system
Child lock
ISM Method
button to select either
Inversion. If you unnecessary to set
language
Normal, White wash,
this function, set Normal.
SOUND
permanent images from the screen.
Note: An excessive permanent image may be impossible
Set ID
Orbiter
TIME
Demo
Factory
reset
SCREEN
removes
to clear
entirely
with White
Wash.
?
Orbiter:
Orbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen
?
will
move
every 2 minutes.
Inversion:
This is the function to invert the
ically
panel
color of the
inverted every 30 minutes.
4. Press the EXIT button to return to normal TV
32
screen.
PLASMA TV
viewing.
The
panel
color is automat-
PIP/DW
Normal
White wash
White wash:
White wash
G
Low power
SPECIAL
?
is
from a PC/video game displayed on the screen for prolonged periods will result in a ghost
when you change the image. Avoid allowing a fixed image to remain on the set's screen for
1. Press the MENU button and then
Orbiter
Prev.
Menu
Menu
Prev.
Inversion
Operation
Low Power
-
This is the function to reduce the power
1. Press the MENU button and then
consumption
of the set.
button to select the SPECIAL
use D / E
menu.
STATION
Menu
Lock
language
2. Press the G button and then
3. Press the G button and then
button to select Low power.
use D / E
button to select On
use D / E
PICTURE
Child lock
ISM method
SOUND
or
system
Off.
Low power
Off
Set ID
TIME
4. Press the EXIT button to return to normal TV
GOn
Demo
Factory
viewing.
reset
SPECIAL
SCREEN
PIP/DW
Prev.
Menu
Demo
-
Use it to
see
the difference between XD demo
-I t 's not available to
use
this function in
1. Press the MENU button and then
on
and XD Demo off.
RGB[PC], HDMI[PC]
use D / E
mode.
button to select the SPECIAL
menu.
STATION
Menu
Lock
language
2. Press the G button and then
3. Press the G button to
4. To
stop
XD
button to select XD Demo.
use D / E
PICTURE
Child lock
ISM method
SOUND
begin
system
XD Demo.
Low power
Set ID
Demo
TIME
Factory
Demo, press the EXIT button.
To start
G
reset
SPECIAL
SCREEN
PIP/DW
Factory
-
-
Use to
Prev.
Menu
Reset
quickly
reset all the
menu
to their
options
original factory preset
values.
This function deletes all TV programmes.
1. Press the MENU button and then
use D / E
button to select the SPECIAL
menu.
STATION
Menu
Lock
2. Press the G button and then
use D / E
3. Press the G button to reset the
The set is switched to
standby
menu
button to select
options
to
original
Factory
reset
menu.
values.
mode.
PICTURE
SOUND
language
system
Child lock
ISM method
If you press
Low power
all
Set ID
be reset.
TIME
user
setting
,
will
Demo
Factory
reset
G
OK
SPECIAL
Note :
a. To begin Factory Reset, input a 4-digit password in Lock system. Be sure to remember
this number!
c. If you forgot your password, press '7', '7', '7', '7' on the remote control handset.
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
33
Operation
Screen
Screen Menu
Auto
-
Options
Options
mode
adjustment (RGB [PC]
Automatically adjusts picture position
1. Press the MENU button and then
only)
and minimizes
use D
image shaking.
/ E button to select the SCREEN
menu.
Auto
STATION
config.
Manual
2. Press the G button and then
3. Press the
?
?
use D
/ E button to select Auto
button to start Auto config..
When Auto config. has finished, Ok will be shown
If the position of the image is still not correct, try Auto
adjusted
more
after Auto
-
-
-
-
SOUND
Zoom +/Position
on screen.
TIME
NR
adjustment again.
adjustment
in RGB
Cinema
SPECIAL
(PC),
you
adjust
can
Reset
SCREEN
Menu
Prev.
viewing.
the image is still not correct, your set is functioning properly but needs further adjustment.
The Auto config. functions don't need to be run for HDMI mode.
This function also adjust sub picture position and minimizes image shaking in RGB[PC] for PIP.
Although
Manual
-
config.
ARC
PIP/DW
5. Press the EXIT button to return to normal TV
To set
VGA Mode
PICTURE
G
4. If picture needs to be
the Manual config..
-
config..
G
Configure
If the
picture
manually.
isn't clear after auto
To correct the
screen
adjustment
and
especially
if characters
are
still
trembling, adjust
the
picture phase
size, adjust Clock.
This function works in the
following
mode
RGB/HDMI[PC], RGB/HDMI[DTV] (480p/576p/720p/1080i),
:
COMPONENT
(480p/576p/720p/1080i).
-I t 's not available to
use
Phase, Clock function in COMPONENT (480p/576p/720p/1080i), RGB/HDMI[DTV]
(480p/576p/720p/1080i)
mode.
1. Press the MENU button and then D / E button to select the SCREEN
2. Press the G button and then D / E button to select Manual
3. Press the
G
button and then D / E button to select
menu.
STATION
PICTURE
config..
Phase, Clock, H-Position
or
V-
SOUND
TIME
appropriate adjustments.
5. Press the EXIT button to return to normal TV
see a
normal
picture,
Clock
0
H-Position
0
V-Position
0
VGA Mode
Zoom +/-
Cinema
Reset
SCREEN
viewing.
PIP/DW
Menu
Prev.
match the resolution of RGB mode and selection of VGA mode.
following
1. Press the MENU button and then
2. Press the
G
button and then
mode:
RGB[PC], HDMI[PC]
button to select the SCREEN
use D / E
use D / E
mode
menu.
button to select VGA Mode.
STATION
Auto
PICTURE
VGA Mode
SOUND
3. Press the G button and then
use D / E
button to select the desired VGA resolution.
4. Press the EXIT button to return to normal TV
viewing.
config.
Manual config.
Zoom +/-
852x480
Cinema
Reset
SCREEN
PIP/DW
PLASMA TV
640x480
848x480
NR
SPECIAL
G
ARC
Position
TIME
34
0
Wide VGA mode
This function works in the
-
Phase
NR
4. Press the F / G button to make
To
G
Position
SPECIAL
-
config.
Manual config.
ARC
Position.
Selecting
Auto
Menu
Prev.
Operation
Picture Format
Setting
-
You
can
watch the
screen
in various
picture formats; Spectacle,
Full
(option), Original, 4:3,
16:9
(Wide),
14:9
and Zoom.
1. Press the MENU button and then
2. Press the G button and then
use D
3. Press the G button and then
Original, 4:3,
16:9
(Wide),
or
menu.
/ E button to select ARC.
button to select
/ E
D
use
14:9
/ E button to select the SCREEN
use D
STATION
Auto
PICTURE
VGA Mode
ARC
Spectacle, Full (option),
SOUND
TIME
Zoom.
SPECIAL
?
Spectacle
Full
signal,
screen
Position
Original
Cinema
4:3
NR
16:9
Reset
14:9
adjust
the
picture
PIP/DW
Menu
Prev.
adjust
fully.
the
picture
it will be
automatically changed
to the
4:3
selection will lead you to view
gray bars appearing at both the left and
picture with
right sides.
a
an
original
4:3
aspect ratio, with
16:9
(Wide)
Following selection
will lead you to adjust the picture horizontally, in
to fill the entire screen (useful for viewing 4:3 formatted DVDs).
?
Full
Original
Following
?
Zoom +/-
(option)
When your TV receives the wide
picture format to be sent.
?
Spectacle
SCREEN
When your TV receives the wide screen signal, when selected it will
horizontally or vertically, in a linear proportion, to fill the entire screen
?
G
Zoom
When your TV receives the wide screen signal, when selected it will
horizontally, in non-linear proportion, to fill the entire screen.
?
config.
Manual config.
a
linear
proportion,
14:9
You
can
enjoy
mode. The
the
screen
picture
format of 14:9
14:9 is viewed
just
TV programme through the 14:9
like that the screen 4:3 is magnified to the left /
or
general
right.
?
Zoom
selection will lead you to view the picture without any alternation, while filling
the entire screen. However, the top and bottom portions of the picture will be cropped.
Following
4.
-
-
-
-
Repeatedly
You
press the MENU button to return to normal TV
viewing.
(Wide) in RGB[PC], HDMI[PC] mode only.
You can
select 4:3, 16:9 (Wide) and Zoom in RGB[DTV], HDMI[DTV], Component [DTV] mode only.
You can
select Spectacle, Full (option), Original, 4:3, 16:9 (Wide), 14:9 and Zoom in DTV, TV, AV1, AV2,
AV3, AV4, AV5, S-Video2 or COMPONENT [480i/576i] mode only.
There might be uncomfortable in full mode. Then change into other mode.
can
only
only
only
select 4:3 and 16:9
Picture Size Zoom
-
When
enlarging
or
reducing
the
picture,
the
screen
may be
display
an
unnatural
1. Press the MENU button and then D / E button to select the SCREEN
2. Press the G button and then D / E button to select Zoom
3. Press the
G
button and then F
/
G
button to make
menu.
+/-.
appropriate adjustments.
looking picture.
STATION
Auto
PICTURE
VGA Mode
ARC
SOUND
viewing.
Zoom +/Position
TIME
4. Press the EXIT button to return to normal TV
config.
Manual config.
100
G
F
%
G
Cinema
NR
SPECIAL
Reset
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
35
Operation
Screen
Screen Menu
Options
Options
Screen Position
-
This function is available after
adjusting
Zoom +/-.
1. Press the MENU button and then D / E button to select the SCREEN
menu.
2. Press the G button and then D / E button to select Position.
3. Press the G button and then D / E
/ G button to
or F
4. Press the EXIT button to return to normal TV
adjust
STATION
Auto
PICTURE
VGA Mode
config.
Manual config.
ARC
the
SOUND
position.
Zoom +/Position
D
G
F
G
E
TIME
Cinema
NR
viewing.
SPECIAL
Reset
SCREEN
PIP/DW
Menu
Prev.
Cinema
-
-
When you watch the movie, this function adjusts the set to the best
This function works in the following mode:
TV, AV1, AV2, AV3, AV4, AV5, S-Video2
1. Press the MENU button and then
2. Press the
G
button and then
or
/
appearance.
COMPONENT 480i/576i.
button to select the SCREEN
use D / E
use D
picture
E
menu.
button to select Cinema.
STATION
Auto
PICTURE
VGA Mode
ARC
SOUND
3. Press the G button and then
use D
/ E button to select On
4. Press the EXIT button to return to normal TV
or
config.
Manual config.
Off.
Zoom +/Position
TIME
Cinema
G
Off
NR
viewing.
SPECIAL
On
Reset
SCREEN
PIP/DW
NR
Menu
Prev.
(Noise Reduction)
1. Press the MENU button and then
2. Press the G button and then
3. Press the G button and then
button to select the SCREEN
use D / E
use D / E
use D / E
menu.
button to select NR.
button to select 3D NR
STATION
Auto
PICTURE
VGA Mode
config.
Manual config.
ARC
or
MPEG NR.
SOUND
Zoom +/Position
TIME
Cinema
NR
4. Press the EXIT button to return to normal TV
viewing.
SPECIAL
G
3D NR
0
MPEG NR
0
Reset
SCREEN
PIP/DW
Initializing (Reset
This function
to
original factory settings
operates in
To initialize the
adjusted
for
current mode.
value
menu.
2. Press the G button and then D / E button to select Reset.
STATION
Auto
PICTURE
VGA Mode
sub
initialize
picture
Position, Zoom +/-, PIP size, PIP position, PIP Transparency and
size of twin
picture.
PLASMA TV
Cinema
NR
SPECIAL
Reset
G
SCREEN
PIP/DW
36
Zoom +/Position
TIME
can
config.
Manual config.
ARC
SOUND
3. Press the G button.
You
Prev.
screen)
1. Press the MENU button and then D / E button to select the SCREEN
?
Menu
Menu
Prev.
To set
Operation
PIP
(Picture-in-Picture)
(Picture-in-Picture)
Feature
PIP lets you view 2 different inputs (sources) on your set screen at the
-I t 's not available to use this function in TELETEXT mode.
-
time.
PIP
Watching
Press the PIP button to show the sub
Each press of PIP button
?
same
changes
picture.
the
screen
display
as
shown below.
RGB
AV1
RGB
RGB
AV1
AV1
10:30
10:30
10:30
RGB
TV
10:30
Note
:
picture size is 1/2 of the main picture, the picture quality may decrease.
of the sub picture can be unnatural because the set displays full screen by synchronizing
between the main picture source and the sub picture source is different in PIP mode.
a.
When the sub
b.
The motion
refresh rate
Programme Selection
Press the PIP PR
+
for Sub Picture
/- button to select
a
Moving
programme for the sub
the PIP
(PIP
the main
mode
picture
source
when the
only)
Press the POSITION button.
picture.
press the D / E
button until desired
Repeatedly
or F
Selecting
an
Input Signal
position is achieved. The sub
picture moves up/down or
left/right.
Source for the PIP
Press the PIP INPUT button
to select the
the sub
In
input
picture.
source
for
/ G
Win.
position
D
FG
E
RGB
AV1
10:30
models, when the
sub picture quality get poor
some
in AV modes for sub
select
picture,
Auto, PAL, SECAM
NTSC in PIP
System
or
menu.
Picture Size
Press the SIZE button and
then F / G button to
POP
(Picture-out-of-Picture:
Channel
the sub
Scan)
Use POP to search the programmes of all the memorized
channels one-by-one on the 3 PIP screen display, (while the
main
of all
remains the current
picture
the programmed
source
channels
are
channel).
The
pictures
searched with the 3 POP
pictures
Adjusting
PIP
are
changed
from the TV/DTV mode.
Transparency (PIP
mode
size.
With SIZE button in
DW2
DW1,
modes, main and sub
picture is adjusted
simultaneously. With
button in PIP
screen.
Notes: Sub
picture
adjust
picture
is
Win. size
F
G
SIZE
mode, sub
adjusted.
only)
1. Press the MENU button and then D / E button to select the PIP/DW
menu.
2. Press the G button and then D / E button to select PIP
Transparency.
3. Press the G button and then F / G button to
adjust
transparency.
4. Press the EXIT button to return to normal TV
viewing.
PIP
Owner's Manual
37
Operation
eletext
Teletext
T
-
Teletext
(or
TOP
text)
(option)
(option)
is
an
optional function,
therefore
only
the set with the teletext
system
can
receive the teletext
broadcast.
-
-
Teletext is
a
free service broadcast
by most TV
prices and many
television programmes, share
The teletext decoder of this set
consists of
can
stations which
other
gives up-to-the-minute
information
on
weather,
news,
topics.
support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext)
number of pages which are selected by directly entering the corresponding page number. TOP and
FASTEXT are more modern methods allowing quick and easy selection of teletext information.
a
Switch on/off
Press the TEXT button to switch to teletext.
?
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are
displayed
on
the
ber indicates your selection, while the second shows the current page
Press the TEXT button to switch off teletext.
SIMPLE Text
Page
headline. The first page
screen
num-
displayed.
(option)
selection
1. Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you
press a wrong number, you must complete the three digit number and then reenter the correct page number.
2. The PR D / E button
TOP Text
The
user
can
also be used to select the
preceding
or
following
page.
(option)
guide displays
four
fields-red, green, yellow and blue
at the bottom of the
screen.
The
yellow
field
denotes the next group and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the
3.
4.
proceed to the next group with automatic overflow to the next block.
With the green button you can proceed to the next existing page with automatic overflow to the next
(Alternatively the PR D button can be used.)
The red button permits to return to previous selection. (Alternatively the PR E button can be used.)
yellow
button to
Direct page selection
Corresponding to the SIMPLE text mode, you
NUMBER buttons in TOP mode.
38
PLASMA TV
can
select
a
page
by entering
it
as a
three
digit
number
group.
using
the
Operation
FASTEXT
The teletext pages are colour coded
sponding coloured button.
Page
the bottom of the
screen
and
selected
are
by pressing
the
corre-
selection
1. Press the
2. You
3.
along
can
button to select the index page.
select the pages which are colour coded
i
Corresponding
to the SIMPLE text
mode, you
along
can
the bottom line with the
select
a
page
by entering
coloured buttons.
same
its three
digit
page number with
the NUMBER buttons in FASTEXT mode.
4. The PR D / E button
Special
can
also be used to select the
preceding
or
following
page.
Teletext Functions
REVEAL
Press this button to
Press this button
display concealed information, such as solutions
again to remove the information from the display.
of riddles
or
puzzles.
SIZE
Selects double
Press this
Press this
Press this
height text.
button to enlarge the top half of the page.
button again to enlarge the bottom half of the
button again to return to the normal display.
page.
UPDATE
Displays
the TV
picture
on
the
Press this button to view the
screen
updated
while
waiting
for the
new
teletext page.
teletext page.
HOLD
Stops
the automatic page
which will
change
occur
if
teletext page consists of 2
a
number of sub pages and the sub page
shown
this button is
left-hand
displayed is, usually,
stop symbol is displayed at the top
pressed the
matic page change is inhibited.
To continue press this button again.
on
the
or more
screen
corner
sub pages. The
below the time. When
of the
screen
and the auto-
MIX
Displays
the teletext pages
To switch the TV
picture
superimposed
the TV
on
off press this button
picture.
again.
TIME
This button has two functions:
a)
When
screen.
b)
viewing
a
TV programme, press this button to
Press this button
In teletext
again
to
remove
mode, press this button
the bottom of the
screen.
Press this button
again
To hold
or
the
to select
change
display
the time at the
top right hand
corner
of the
display.
a
sub page number. The sub page number is
the sub page, press the RED/ GREEN
or
displayed
at
PR D / E buttons.
to exit this function.
Owner's Manual
39
Miscellaneous
Brief Info.
-
-
Show the
present
screen
Press the INFO/ i /*
(In
(In Digital
button
or
EXIT button to exit.
Function
to Now/Next
F/G
Change
D/E
The detail information
EPG
(Electronic
(Electronic
mode
(In
(In Digital
-
-
-
-
This
(Electronic Programme Guide) (In Digital
system has
only)
only)
information.
Remote Control Buttons
EPG
mode
off
Programme Guide)
Guide)
only)
only)
mode
only)
(EPG) to help your navigation through all the possible viewing options.
The EPG supplies information such as programme listings, start and end times for all available services. In addition,
detailed information about the programme is often available in the EPG (the availability and amount of these programme
details will vary, depending on the particular broadcaster).
This function can be used only when the EPG information is broadcasted by broadcasting companies.
The EPG displays the programme description for next 8 days.
an
Electronic
on or
Programme
Guide
Switch on/off EPG
1.
Press the GUIDE button to switch
2.
Press the GUIDE button
Select
a
again
on
EPG.
to switch off EPG and return to TV
viewing.
programme
Press the D / E
,
F / G button to select desired
programme.
Pressing the PR D /
E
button
repeatedly
programme, then press the OK button to
display
the selected
turns the pages.
3
Event Information
displays
the selected Event
Information such
Name,
Start Time, End Time,
as
Description.
2
Programme
displays
the searched
Channel after
Auto
40
tuning the
Programme.
PLASMA TV
1
Event
displays
the Event Name
which broadcasts at
or
next.
present
Miscellaneous
Button Function in NOW/NEXT Guide Mode
Remote Control Buttons
RED
Function
D/E
change to 8 Days Guide
Select a broadcasting station
F/G
Select the Event
FAV
Shows the favourite programmes
BLUE
The detail information
Button Function in 8
Mode
Days
Guide/Date
Change
on or
off
Mode
Remote Control Buttons
Function
GREEN
Shows the Date Box
RED
Mode
D/E
change to Channel Guide
Select a broadcasting station
F/G
Select the Event
FAV
Shows the favourite programmes
BLUE
The detail information
EXIT
Switch off EPG
on or
off
Owner's Manual
41
Miscellaneous
EPG
(Electronic
(Electronic
mode
(In
(In Digital
Programme Guide)
Guide)
only)
only)
Button Function in Channel Guide Mode
Remote Control Buttons
Function
GREEN
Shows the Date Box
RED
Mode
D/E
Select the Event
F/G
Select
FAV
Shows the favourite programmes
BLUE
The detail information
Button Function in Extended
change
a
to NOW/NEXT Guide
broadcasting
Description
42
off
Function
BLUE
The detail information
D/E
Text
PLASMA TV
on or
Box
Remote Control Buttons
PRD/E
station
Up/Down
Page Up/Down
on or
off
Miscellaneous
External Control
Control Device
-
Connect the RS-232C
and control the set's
input jack to an external
functions externally.
How to connect external control
?
Connect the serial
?
RS-232C connection cables
?
The set remote control and front
computer
<
Back
panel
Type
or
of the set
as a
computer
or an
A/V control
system)
to the RS-232C
jack
on
supplied with the set.
panel controls (except main power)
the back
panel
of the set.
not
will not be functional if the set is controlled
by
a
PC
other external device.
>
of connector; D-Sub
No.
Pin
1
No connection
2
RXD
3
TXD
4
DTR
5
GND
9-pin
male
1
name
6
DSR
7
RTS
5
(Receive data)
(Transmit data)
(DTE side ready)
9
(DCE side ready)
(Ready to send)
(Clear to send)
8
CTS
9
No Connection
RS-232C
(such
equipment
port of the control device
are
control device
Setup
Setup
6
configurations
3-wire
configuration
(Not standard)
7-wire
configuration
(Standard RS-232C cable)
PC
PDP
PC
PDP
RXD
3
TXD
RXD
2
TXD
TXD
2
RXD
TXD
3
RXD
5
GND
GND
5
6
DSR
DTR
4
4
DTR
DSR
6
8
CTS
RTS
7
7
RTS
CTS
8
GND
DTR
DSR
RTS
CTS
2354678
D-Sub 9
D-Sub 9
D-Sub 9
3254678
GND
DTR
DSR
RTS
CTS
D-Sub 9
Owner's Manual
43
Miscellaneous
Set ID
-
-
Use this function to
specify a
Mapping
Refer to 'Real Data
set ID number.
1'. See page 49.
1. Press the MENU button and then
use
the D
button to select the SPECIAL
/ E
menu.
STATION
Menu
Lock
2. Press the G button and then
3. Press the G button and then
use D / E
use
button to select Set ID.
F / G button to
adjust
PICTURE
language
system
Child lock
ISM method
SOUND
Set ID to choose the desired
Low power
Set ID
TIME
monitor ID number.
G
1
Demo
Factory
reset
SPECIAL
?
4.
The
adjustment
range of Set ID is 1
~
99.
SCREEN
press the MENU button to return to normal TV
Repeatedly
viewing.
PIP/DW
MENU Prev.
Communication Parameters
?
Baud rate
?
Data
:
9600
length
Parity : None
?
*
Use
:
a
bps (UART)
?Stopbit:1bit
8 bits
crossed
?
(reverse)
Communication code
:
ASCII code
cable.
Command Reference List
COMMAND 1
COMMAND 2
DATA
(Hexadecimal)
01. Power
k
a
Input Select
Aspect Ratio
k
b
k
c
04. Screen Mute
k
d
02.
03.
05. Volume Mute
k
06. Volume Control
k
07. Contrast
k
e
f
0~1
Refertop.45
Refertop.45
09. Colour
k
i
0~64
10. Tint
k
j
0~64
11.
k
k
0~64
k
l
0~1
k
m
k
n
0~3
15. PIP Position
k
q
0~3
16. Treble
k
r
0~64
17. Bass
k
s
0~64
18. Balance
k
t
0~64
19. Colour
k
u
0~3
20.
k
v
0~50
k
w
0~50
21. Green
22.
Adjustment
Blue Adjustment
23. PIP
input
k
Source
k
$
y
0~50
k
z
0~a
25. ISM Method
j
p
j
q
r
j
s
j
jt
u
j
0~3
27. Orbiter Time
28.
29.
30.
Setting
Orbiter Pixel Setting
Picture Size Setting for DW Mode
Auto Configure
31. Tune Command
m
a
32. Send IR Code
m
c
x
b
33.
34.
*
Input
Input
When
44
select
select
setting
(Main)
(PIP)
the 24
PLASMA TV
x
34,
~
a menu
y
doesn't
Second command to control the set.
:
You
can
adjust
the set ID to choose
Adjustment range is 1
When selecting Set ID
Set ID is indicated
[DATA]
*
[Cr]
Carriage
:
decimal
Return
ASCII code '0x0D'
*[]
ASCII code
:
'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
*
The set transmits ACK
(acknowledgement)
based
format when
normal data. At this
time, if the data
receiving
on
this
is data read
mode, it indicates present status data. If the
data is data write mode, it returns the data of the PC computer.
[Command2][ ][Set ID][ ][NG][Data][x]
on screen.
as
command.
1~3
display
'0', every
Transmit 'FF' data to read status of
Error Acknowledgement
Refertop.48
Key Code
Refertop.49
Refertop.49
99.
To transmit command data.
:
1~FE
1
~
(1~99)on
menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
0~1
0~20
special
connected the set is controlled.
Refertop.47
24. Abnormal Status
26. Low Power
:
menu.
0~1
14. PIP/DW
Temperature (CSM)
Red Adjustment
[Command 2]
[Set ID]
desired monitor ID number in
*
13. Remote control lock mode
First command to control the set.
:
0~64
0~64
12. OSD Select
[Command 1]
(j,k,morx)
0~1
h
Sharpness
*
*
k
Protocol
[Command1][Command2][ ][Set ID][ ][Data][Cr]
*
0~64
Brightness
Receiving
Transmission
0~1
g
08.
Transmission /
*
The set transmits ACK
(acknowledgement)
format when
abnormal data from
receiving
non-viable functions
Data
1:
Illegal
2: not
or
communication
Code
support function
3: Wait
more
time
based
errors.
on
this
Miscellaneous
01. Power
2
(Command
:
a)
G To control Power On/Off of the
set.
04. Screen Mute
(Command
G To select
mute on/off.
screen
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][d][ ][Set ID][ ][Data][Cr]
Data
0
Power Off
:
Data
1:PowerOn
0
:
Screen mute off
1
:
Screen mute
on
Ack
2
d)
:
(Picture on)
(Picture off)
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
[d][ ][Set ID][ ][OK/NG][Data][x]
G To show Power On/Off.
Transmission
05. Volume Mute
(Command
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume
mute on/off.
Ack
You
adjust
mute
the MUTE button
using
on
Transmission
In like manner, if other functions transmit '0xFF' data
based on this format, Acknowledgement data feed back
[k][e][ ][Set ID][ ][Data][Cr]
Data
status about each function.
presents
also
e)
:
remote control.
[a][ ][Set ID][ ][OK/NG][Data][x]
*
can
2
0
:
Volume mute off
1
:
Volume mute
on
(Volume on)
(Volume off)
Ack
[e][ ][Set ID][ ][OK/NG][Data][x]
Input Select (Command
02.
G To select input
You
also select
can
button
source
an
2
b)
:
for the set.
input
source
using
the INPUT
the set's remote control.
on
06. Volume Control
You
on
[k][b][ ][Set ID][ ][Data][Cr]
0
:DTV
1
:
2
:AV1
3
:AV2
can
also
adjust
remote control.
4
:
Component
6
:
RGB-DTV
[k][f][ ][Set ID][ ][Data][Cr]
7
:
RGB-PC
Data
Min:0~Max:64
*
Refer to 'Real data
mapping
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
[f][ ][Set ID][ ][OK/NG][Data][x]
07. Contrast
Aspect
(Command
2
:
c) (Main
Picture
Size)
G To adjust
You
G To adjust the
You
screen
format.
also
(Main picture format)
screen format using the ARC
adjust the
(Aspect Ratio Control) button
can
SCREEN
on
remote control
or
in the
menu.
1
:
2
:
3
:
(4:3)
Wide screen (16:9)
Horizon (Spectacle)
screen
6
:
Original
aspect ratio.
menu.
mapping
1'. See page 49.
7:14:9
8:Full
08.
[c][ ][Set ID][ ][OK/NG][Data][x]
input,
contrast in the PICTURE
Refer to 'Real data
Brightness (Command
G To adjust
the PC
adjust
[g][ ][Set ID][ ][OK/NG][Data][x]
Ack
Using
contrast.
Ack
4:Zoom
*
also
g)
:
Min:0~Max:64
*
Normal
screen
2
[k][g][ ][Set ID][ ][Data][Cr]
Data
[k][c][ ][Set ID][ ][Data][Cr]
can
(Command
1'. See page 49.
Transmission
Transmission
Data
f)
Transmission
Analogue
Ratio
:
volume with the volume buttons
Ack
03.
2
G To adjust volume.
Transmission
Data
(Command
you select either 16:9
You
or
4:3
screen
can
2
brightness.
adjust brightness
:
h)
screen
also
in the PICTURE
menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Refer to 'Real data
mapping
1'. See page 49.
Ack
[h][ ][Set ID][ ][OK/NG][Data][x]
Owner's Manual
45
Miscellaneous
09. Colour
G To adjust the
You
can
2
(Command
also
screen
adjust
14.PIP/DW(Command2:n)
i)
:
G To control the PIP (Picture In picture)/DW.
colour.
colour in the PICTURE
You
menu.
on
Transmission
in the PIP/DW
or
the PIP/DW button
menu.
[k][n][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
the remote control
using
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
also control the PIP/DW
can
Refer to 'Real data
1'. See page 49.
mapping
Data
0: PIP/DW off
Ack
1: PIP
[i][ ][Set ID][ ][OK/NG][Data][x]
2: DW1
3: DW2
10. Tint
(Command
G To adjust the
You
can
also
screen
adjust
2
:
Ack
j) (option)
[n][ ][Set ID][ ][OK/NG][Data][x]
tint.
tint in the PICTURE
menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
15. PIP Position
Data
G To select sub picture position for PIP.
Red:0~Green:64
*
Refer to 'Real data
1'. See page 49.
mapping
You
also
can
TION button
Ack
[j][ ][Set ID][ ][OK/NG][Data][x]
11.
You
can
also
adjust
the sub
2
k)
:
sharpness.
adjust sharpness in
Data
screen
the remote control
on
q)
picture position using
the PICTURE
menu.
down
0
:
Right
or
in the PIP/DW
POSImenu.
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
[k][k][ ][Set ID][ ][Data][Cr]
Ack
Data
[q][ ][Set ID][ ][OK/NG][Data][x]
Min:0~Max:64
Refer to 'Real data
:
[k][q][ ][Set ID][ ][Data][Cr]
Transmission
*
2
Transmission
Sharpness (Command
G To adjust the
(Command
1'. See page 49.
mapping
Ack
[k][ ][Set ID][ ][OK/NG][Data][x]
16. Treble
12. OSD Select
(Command
2
:
(Command
2
:r)
G To adjust treble.
l)
You
G To select OSD (On Screen Display) on/off when
can
also
adjust
treble in the SOUND
menu.
con-
Transmission
trolling remotely.
[k][r][ ][Set ID][ ][Data][Cr]
Transmission
Data
[k][l][ ][Set ID][ ][Data][Cr]
Data0
:OSDoff
Min:0~Max:64
*
1:OSDon
Refer to 'Real data
mapping
1'. See page 49.
Ack
Ack
[r][ ][Set ID][ ][OK/NG][Data][x]
[l][ ][Set ID][ ][OK][Data][x]
13. Remote control lock mode
G
To lock the front
panel
controls
(Command
on
2
:
m)
the set and remote
trol.
You
[k][m][ ][Set ID][ ][Data][Cr]
0
:
Lock off
1:Lockon
Data
you're
not
using
the remote
When main power is
released.
46
:
s)
PLASMA TV
can
also
adjust
bass in the SOUND
menu.
[k][s][ ][Set ID][ ][Data][Cr]
control,
Min:0~Max:64
*
[m][ ][Set ID][ ][OK/NG][Data][x]
If
2
Transmission
Ack
*
(Command
G To adjust bass.
Transmission
Data
con-
17. Bass
use
this mode.
on/off, external control lock is
Refer to 'Real data
mapping
Ack
[s][ ][Set ID][ ][OK/NG][Data][x]
1'. See page 49.
Miscellaneous
18. Balance
(Command
2
:
G
G To adjust balance.
You
can
also
adjust
balance in the SOUND
To select
picture using
for sub
also
can
y)
:
picture in PIP/Twin picadjust input source for sub
PIP INPUT button
remote control.
on
[k][y][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
Refer to 'Real data
source
2
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
*
input
ture mode. You
menu.
Transmission
Data
Input Select (Command
23. PIP
t)
mapping
1'. See page 49.
Data
Ack
[t][ ][Set ID][ ][OK/NG][Data][x]
0
:DTV
1
:
2
:AV1
3
:AV2
Analogue
4
:
Component
6
:
RGB-DTV
7
:
RGB-PC
Ack
19. Colour
2
Temperature (Command
:
u)
G To adjust colour temperature.
You
can
also
adjust
CSM in the PICTURE
menu.
Transmission
0: Normal
24. Abnormal State
G To recognize
[k][u][ ][Set ID][ ][Data][Cr]
Data
[y][ ][Set ID][ ][OK/NG][Data][x]
(Command
2
:
z)
abnormal state.
an
Transmission
1: Cool
2: Warm
3: User
[k][z][ ][Set ID][ ][FF][ ][Cr]
Ack
Data
[u][ ][Set ID][ ][OK/NG][Data][x]
Ack
FF
:
Read
[z][ ][Set ID][ ][OK/NG][Data][x]
Data
20. Red
Adjustment (Command
2
0: Normal
1:
v)
:
2:
G To adjust red in colour temperature.
3:
Transmission
4:
5: 5V down
[k][v][ ][Set ID][ ][Data][Cr]
Data
6: AC down
Min:0~Max:50
*
Refer to 'Real data
7: Turn the set off
mapping
2'. See page 49.
8: Turn the set off
9: Turn the set off
Ack
a:
[v][ ][Set ID][ ][OK/NG][Data][x]
*
21. Green
Adjustment (Command
2
:
w)
Fan Alarm function
(option)
Off time function
Auto
function
sleep
AV board detect
only".
1
:
j, Command
G To control the ISM method. You
Method in SPECIAL
[k][w][ ][Set ID][ ][Data][Cr]
2
can
:
p)
also
adjust
ISM
menu.
Transmission
Min:0~Max:50
Refer to 'Real data
by
by
by
by
25. ISM Method
(Command
Transmission
*
Turn the set off
This function is "read
G To adjust green in colour temperature.
Data
(Power on and signal exist)
No signal (Power on)
Turn the set off by remote control
Turn the set off by sleep time function
Turn the set off by RS-232C function
mapping
2'. See page 49.
Ack
[j][p][ ][Set ID][ ][Data][Cr]
Data
[w][ ][Set ID][ ][OK/NG][Data][x]
1
:
Inversion
4
:
White wash
2
:
Orbiter
8
:
Normal
Ack
[p][ ][Set ID][ ][OK/NG][Data][x]
22. Blue
Adjustment (Command
2
:
$)
G To adjust blue in colour temperature.
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:50
*
Refer to 'Real data
mapping
2'. See page 49.
Ack
[$][ ][Set ID][ ][OK/NG][Data][x]
Owner's Manual
47
Miscellaneous
26. Low Power
(Command
30. Auto
1
:
j, Command
2
:
q)
G To reduce the power consumption of the
also
adjust
Low Power in SPECIAL
Configure
(Command 1 : j, Command
set. You
can
It works
Transmission
[j][q][ ][Set ID][ ][Data][ ][Cr]
[j][u][ ][Set ID][ ][Data][Cr]
Data
0:Off
in RGB
only
Transmission
Data
:
u)
G To adjust picture position and minimize image shaking
automatically.
menu.
2
mode.
(PC)
1: To set
Ack
1:On
Ack
[u][ ][Set ID][ ][OK/NG][Data][x]
[q][ ][Set ID][ ][OK/NG][Data][x]
31. Channel Select Command
27. Orbiter Time
(Command
1
Setting
: j, Command
G To adjust orbiter operation time
2
:
(Command
r)
G Select channel
term.
m, Command 2
1
:
to
following physical
:
a)
number.
Transmission
Transmission
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
[j][r][ ][Set ID][ ][Data][ ][Cr]
Data
Min: 1
~
Max: FE
Refer to 'Real data
*
mapping
Data0
:
High
Data1
:
Low channel data
1'.
channel data
No. 47
ex.
Ack
->
No. 394
Data2
[r][ ][Set ID][ ][OK/NG][Data][x]
28. Orbiter Pixel
(Command
1
Setting
: j, Command
00 2F
->
01
0x00
:
ATV Main
0x01
:
ATV Sub
0x10
:
DTV Main
0x11
:
DTV Sub
Channel data range
Analogue Min: 00
-
2
:
s)
Digital
G To adjust pixel number in orbiter function.
ex)
Transmission
-
(2FH)
88 (188H)
Min: 00
~
~
Max: 63
Max: 3E7
(0~99)
(0~999)
In ATV Main and DTV Sub mode
1. Auto
Programme
or
Manual
[j][s][ ][Set ID][ ][Data][Cr]
2. "ma 1 00 08 00"
-->
Select
Data
3. "ma 1 00 0E 11"
-->
Select
Min:1~Max:3
Refer to 'Real data
*
mapping
Programme
8 channel (ATV Main)
14 channel (DTV Sub)
1'.
Ack
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
[s][ ][Set ID][ ][OK/NG][Data][x]
Data
Min: 00
~
Max: FF
29. Picture Size
Setting for DW Mode
(Command 1 : j, Command 2 : t)
32. Send IR Code
G To select the PIP picture format.
You
also select the PIP
can
SIZE
on
picture
the remote control.
format
using
(Command
the
G To send IR
1
:
remote
m, Command 2
key
code.
Transmission
Transmission
[j][t][ ][Set ID][ ][Data][Cr]
[m][c][ ][Set ID][ ][Data][Cr]
Data
Data
Min: 0
*
~
Max: 20
Refer to 'Real data
mapping
-
Refer to page 51.
1'.
Ack
Ack
[t][ ][Set ID][ ][OK/NG][Data][x]
48
Key
code
PLASMA TV
[c][ ][Set ID][ ][OK/NG][Data][x]
:
c)
Miscellaneous
33.
Input select (Main)
(Command 1 : x, Command
G To select input
source
for main
34.
2
:
b)
G To adjust input
picture.
source
for sub
2
picture
y)
:
in PIP mode.
Transmission
Transmission
[x][y][ ][Set ID][ ][Data][Cr]
[x][b][ ][Set ID][ ][Data][Cr]
Data
Input select (PIP)
(Command 1 : x, Command
Data
Structure
Structure
MSB
MSB
0
LSB
LSB
0
0000000
0000000
External
External
Input
Input
Input
External
Input
0000
D TV
0001
Analogue
0010
AV
0011
S-Video
0100
Component
0101
RGB-DTV
0110
RGB-PC
1001
HDMI
Data
0000
D TV
0001
Analogue
0010
AV
0011
S-Video
0100
Component
0101
RGB-DTV
0110
RGB-PC
1001
HDMI
Input
Number
Data
Data
0000
Input1
0000
Input1
0001
Input2
0001
Input2
0010
Input3
0010
Input3
0011
Input4
0011
Input4
0100
Input5
0100
Input5
0101
Input6
0101
Input6
Input
Number
Number
Input
Number
Data
Input
External
Ack
Ack
[y][ ][Set ID][ ][OK/NG][Data][x]
[b][ ][Set ID][ ][OK/NG][Data][x]
*
Real data
0
mapping
1
:Step0
*
Real data
mapping
2
0:-40
1:-39
A
:Step10(SetID10)
2:-38
F
:Step15(SetID15)
10:Step16(SetID16)
28:0
64
4E:+38
:
Step
100
6E
:
Step
110
73
74
:
Step
Step
115
116
C7
:
Step
199
FE
FF
:
Step
Step
254
255
:
:
4F:+39
50:+40
Owner's Manual
49
Miscellaneous
IR Code
Code
(NEC
(NEC Format)
How to connect
G
Connect your wired remote control to the Remote Control
Remote Control IR Code
port
on
the set.
(NEC Format)
G Output waveform
Single pulse,
modulated with 37.917KHz
at 455KHz
signal
TC
Carrier
frequency
FCAR
1/TC
Duty
T1
=
ratio
=
=
fOSC/12
T1/TC
1/3
=
G Configuration of frame
?
1st frame
Lead
Low
High
code
custom code
custom code
Data code
Data code
C0 C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7
?
Repeat
frame
Repeat
code
Tf
G Lead code
9ms
4.5
ms
0.55
G Repeat code
ms
9ms
2.25
ms
G Bit description
?
Bit "0"
?
0.56
0.56
ms
1.12
G Frame interval
:
Bit "1"
2.24
ms
Tf
The waveform is transmitted
Tf
as
long
as a
key
is
depressed.
Tf
Tf=108ms @455KHz
50
PLASMA TV
ms
ms
Miscellaneous
Code
Function
(Hexa)
Note
00
PRD
R/C Button
01
PRE
R/C Button
02
VOL D
R/C Button
03
VOL E
R/C Button
40
Up (D)
R/C Button
41
Down
R/C Button
06
07
(E)
Right (G)
Left (F)
R/C Button
R/C Button
POWER
R/C Button
C4
POWER ON
Discrete IR
C5
POWER OFF
Discrete IR
09
MUTE
R/C Button
10
Number
11
Number
12
Number
13
Number
14
Number
15
Number
16
Number
17
Number
18
Number
19
Number
0B
INPUT
R/C Button
BF
COMPONENT
Discrete IR Code
C6
HDMI
Discrete IR Code
D5
RGB
Discrete IR Code
D6
TV
Discrete IR Code
5A
AV1
Discrete IR Code
D0
AV2
Discrete IR Code
D1
AV3
Discrete IR Code
D2
AV4
Discrete IR Code
D3
S-Video2
Discrete IR Code
AB
GUIDE
R/C Button
39
SUBTITLE/*
R/C Button
5B
EXIT
R/C Button
1E
FAV
R/C Button
1A
Q.VIEW
R/C Button
50
D/A TV
R/C Button
0A
I/II
R/C Button
0E
SLEEP
R/C Button
43
MENU
R/C Button
44
OK(
R/C Button
4D
PSM
R/C Button
52
SSM
R/C Button
53
LIST
R/C Button
20
TEXT
R/C Button
2A
REVEAL
R/C Button
24
MIX
R/C Button
26
TIME
R/C Button
62
UPDATE / POSITION
R/C Button
64
SIZE
R/C Button
65
HOLD
R/C Button
70
INDEX
R/C Button
60
PIP/DW
R/C Button
C3
PIP INPUT
R/C Button
C2
SWAP
R/C Button
C0
PIP PR+
R/C Button
C1
PIP PR-
R/C Button
61
BLUE
R/C Button
72
Key
YELLOW Key
GREEN Key
RED Key
79
ARC
R/C Button
76
ARC
77
ARC
AF
ARC
08
63
71
Key
Key
Key
Key
Key
Key
Key
Key
Key
Key
0
R/C Button
1
R/C Button
2
R/C Button
3
R/C Button
4
R/C Button
5
R/C Button
6
R/C Button
7
R/C Button
8
R/C Button
9
R/C Button
)
(4:3)
(16:9)
(Zoom)
(Power On/Off)
Code (Only Power On)
Code (Only Power Off)
COMPONENT
(Input
(Input
(Input
(Input
(Input
(Input
(Input
(Input
(Input
Selection)
HDMI Selection)
RGB Selection)
TV Selection)
AV1 Selection)
AV2 Selection)
AV3 Selection)
AV4 Selection)
S-Video2 Selection)
(Only
(Only
(Only
4:3
R/C Button
R/C Button
R/C Button
Discrete IR Code
Discrete IR Code
Discrete IR Code
mode)
16:9 mode)
Zoom mode)
Owner's Manual
51
Miscellaneous
Programming
G
The remote is
multi-brand
a
or a
the Remote
universal remote. It
can
be
programmed
to
operate
most remote-controllable devices of
turn
the device such
other manufacturers.
Note that the remote may not control all models of other brands.
Programming
a
a
code
code into
into
a
a
remote mode
1. To find out whether your remote can operate the device without
press the corresponding mode button on the remote.
programming,
on
as a
VCR and
After
that, press the POWER button. If the device is turned off then it responds properly and the remote needs not to
be programmed. If not, the remote should be programmed to operate the device. The programming procedures are
explained
below.
2. Press the MENU and MUTE button
continuously
at the
same
time for 2
seconds, the
current selected device button
will be illuminated.
If you don't press any button for 20
repeat from step 2.
seconds, the light
3. Enter code numbers
pressing
the
using the number button
button, the light blinks at a time.
on
52
PLASMA TV
see
if the device
the mode button will be turned off. In that case, you have to
the remote
by referring
If the device is turned
4. Press the MENU button to store the code. After
5. Test the remote functions to
on
blinking twice,
the code table
on
the
off, the programming
this code is stored.
responds properly.
If not,
repeat from step
2.
pages. When
is successful.
following
Miscellaneous
Programming
Codes
Codes
VCRs
VCRs
Brand
Codes
Brand
Codes
AIWA
034
KENWOOD
014
034
AKAI
016
043
047
048
125
146
001
012
013
020
101
106
114
123
046
124
LG
AMPRO
072
ANAM
031
033
103
AUDIO DYNAMICS
012
023
039
BROKSONIC
035
037
129
CANON
028
031
033
CAPEHART
108
CRAIG
003
040
135
CURTIS MATHES
031
033
041
DAEWOO
005
007
010
064
065
108
110
111
112
116
117
119
043
(GOLDSTAR)
039
043
PORTLAND
108
TATUNG
039
043
PULSAR
072
TEAC
034
039
043
QUARTZ
QUASAR
011
014
TECHNICS
031
033
070
033
066
075
145
TEKNIKA
019
031
033
034
RCA
013
020
033
034
003
009
013
014
040
041
062
063
THOMAS
034
017
034
101
106
107
109
140
144
TMK
006
145
147
TOSHIBA
008
013
042
047
003
008
010
014
059
082
112
131
031
033
034
040
TOTEVISION
040
101
053
054
101
UNITECH
040
MAGIN
040
MAGNAVOX
031
033
067
068
012
031
034
033
041
REALISTIC
067
RICO
058
VECTOR RESEARCH
012
MARTA
101
RUNCO
148
VICTOR
048
MATSUI
027
030
SALORA
014
VIDEO CONCEPTS
012
MEI
031
033
SAMSUNG
032
040
102
104
VIDEOSONIC
040
MEMOREX
003
010
014
031
105
107
109
112
WARDS
033
034
053
072
113
115
120
122
101
102
134
139
125
059
012
023
DYNATECH
034
053
ELECTROHOME
059
EMERSON
006
017
025
027
MGA
045
046
029
031
034
035
MINOLTA
013
020
036
037
046
101
MITSUBISHI
013
020
045
046
129
131
138
153
049
051
059
061
FISHER
003
008
009
010
151
FUNAI
034
GE
031
033
063
107
109
144
GO VIDEO
132
136
HARMAN KARDON
012
045
HITACHI
004
018
026
043
063
137
INSTANTREPLAY
031
033
JCL
031
033
JCPENNY
012
013
015
040
066
101
034
040
072
MULTITECH
024
034
147
NEC
012
023
039
034
OPTONICA
053
054
150
PANASONIC
066
070
074
133
140
145
013
020
031
031
033
043
048
050
055
060
130
150
152
013
017
024
031
033
034
040
053
054
131
043
048
135
YAMAHA
012
034
039
SANYO
003
007
010
014
ZENITH
034
048
056
102
134
058
072
080
017
037
112
129
003
008
009
010
013
014
017
020
031
042
073
081
054
149
SCOTT
043
101
043
101
043
012
003
022
SEARS
NORDMENDE
033
046
SANSUI
048
PENTAX
034
131
MTC
JVC
101
069
DBX
043
Codes
LXI
108
JENSEN
Brand
034
MARANTZ
043
Codes
LLOYD
DAYTRON
039
Brand
083
031
034
067
PHILIPS
031
033
034
067
071
101
031
SHINTOM
024
SONY
003
009
031
052
056
057
058
076
077
078
149
033
034
033
063
PHILCO
SHARP
054
SOUNDESIGN
034
STS
013
SYLVANIA
031
059
067
PILOT
101
PIONEER
013
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
022
MAGNAVOX
013
PHILIPS
013
SONY
007
DENON
020
014
MARANTZ
024
PIONEER
004
THOMPSON
005
006
GE
005
006
MITSUBISHI
002
PROCEED
021
TOSHIBA
019
008
HARMAN KARDON 027
NAD
023
PROSCAN
005
006
YAMAHA
009
018
JVC
012
ONKYO
008
017
RCA
005
006
ZENITH
010
016
LG
001
PANASONIC
003
009
SAMSUNG
011
015
021
048
SYMPHONIC
034
TANDY
010
034
DVD
DVD
Brand
010
016
025
026
025
Owner's Manual
53
Miscellaneous
Checklist
T
Checklist
roubleshooting
Troubleshooting
No
picture
&
?
Check whether the set is turned
?
Power cord inserted into wall outlet?
?
Plug
another
cord
was
on.
No sound
Press the VOLUME
?
Sound muted? Press MUTE button.
?
Check to
causing
?
The remote control
see
to
p.6)
Poor
one
of the
batteries.
as
the
(Refer
to
image
is muted
p.6)
Please contact your service centre, if
minutes.
Select Colour in the PICTURE
to
menu
?
Activate any function to restore the
still
the set.
and press the VOLUME
button.
inside the set
picture
is
on
the
screen
for
?
Check for local interference such
?
Adjust
?
A
PLASMA TV
Balance in the SOUND
change
in ambient
at the time of
set.
(G)
after five
certain distance between the set and the VCR.
Keep
a
during the startup process of
the picture has not appeared
p.26)
?
speakers
Unusual sound from
polarities.
This is normal
new
brightness
more
as an
than 5
of the
menu.
electrical
(Refer
picture.
minutes, the
picture shaking
No output from
54
installed with the correct
?
(If
or
are
Install
picture
Horizontal/vertical bars
if the batteries
between the set and the remote control
object
?
(Refer
or
if there is any
obstruction.
Check if the remote control handset is set up to correct mode.
?
Poor colour
button.
?
Picture appears slowly,
after switching on
or
(G)
see
Check to
(Refer
doesn't work
No
power cord into the wall outlet where the set's power
?
Picture OK &
No sound
product's
plugged in.
to
appliance
screen
or
gets dark.)
power tool.
p.27)
humidity or temperature may result in an
switching off or on of the set and do not indicate
unusual noise
a
fault with the
Miscellaneous
Product
Specifications
Specifications
MODEL
Width
42PX4DVA-ZC
(inches
/
mm)
49.3 / 1252
Height (inches
/
mm)
27.8 / 705
Depth (inches
/
mm)
11.3 / 285
Weight (pounds
Power
/
84.5 / 38.3
kg)
requirement
AC100-240V, 50/60Hz
32
Operating Temperature Range
The
specifications
shown above may be
(0
40°C)
~
Less than 80%
Operating Humidity Range
?
104°F
~
changed
without notice for
quality improvement.
Owner's Manual
55
Download PDF

advertising