LG | 42PX4DV | LG 42PX4DV Owner’s Manual

PLASMA TV
OWNER'S MANUAL
Please read this manual
carefully
before
operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back
mation to your dealer when you
Model number
:
Serial number
:
P/NO
:
3828VA0536E
(DF054A,
cover
require
141D
TX)
and
quote this infor-
service.
Safety Warnings
Instructions
Safety
Safety
W
WARNING
Do not
place the
set in direct
sunlight
or
near
heat
Do not
-
sources
such
This may
-
as
heat
cause a
fire.
registers,
stove and
so on.
In
Do not
use
or
place
any
This may
-
Bend
the set in
where
cause a
antenna
building
to
damp place such as
it is likely to get wet.
fire
cable
prevent
could
give
an
between
rain from
This may cause water
electric shock.
-
or
damaged
a
bathroom
and
inside
-
outside
inside the set and could
give
an
Earth wire should be connected.
or
Do not
-
danger
a
of
or
the set
strange smell
set.
could
or
give
from the
an
electric
set, switch
from the wall outlet and contact your
service centre.
This may
cause a
attempt
This may
shock.
During
If the earth wire is not connected, there is possible
electric shock caused by the current leakage.
-
of smoke
your dealer
in.
cleaning the
damaged
cause
,unplug it
dealer
electric shock.
flowing
case
it off
water while
use
This may
shock.
or
or
could
give
an
electric shock.
to service the set
yourself. Contact
service centre.
cause
storm
fire
damaged
the set
or
activity, unplug the
could
give
an
electric
set from the wall
outlet and don't touch the antenna cable.
-
This may
shock.
cause
damaged
the set
or
could
give
an
electric
Power
DISCONNECTING DEVICE FROM MAINS
supplier
-
Mains
plug is the disconnecting
readily operable.
device. The
plug
must remain
Short-circuit
breaker
-
If
-
are not possible, a separate circuit breakemployed and installed by a qualified electrician.
connect ground to telephone wires, lightning rods or gas
grounding
er
methods
should be
Do not
pipe.
Do not
place anything containing liquid
on
top
of the
set.
-
This may
cause a
Do not insert any
-
This may
Do not
-
cause a
fire
or
could
cause
an
or
could
serious
injury
give
on
to
a
an
2
This set is
vent.
electric shock.
the set.
child
WARNING in U.K.
*
electric shock.
object into the exhaust
fire
place heavy objects
This may
give
or
adult.
only
with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse
always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To
obtain a replacement fuse cover contact your dealer or "LG Electronics U.K. Ltd." If the type of plug supplied is not
suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted.
A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is
hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or
with the earth symbol
or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse,
either in the plug, or at the distribution board.
The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or coloured red.
PLASMA TV
supplied
Safety Warnings
*
Safety
instructions have two kinds of
WARNING
NOTES
information, and each meaning of it is
as
below.
The violation of this instruction may
cause
serious
The violation of this instruction may
cause
light injuries
product.
Take
care
of
under
danger that may happen
injuries
or
and
even
damage
death.
of the
specific condition.
NOTES
Never touch the power
-
This may
cause an
plug with
a
wet hand.
Ensure the power cord doesn't trail
like a heater.
electric shock.
-
Disconnect from the mains and
tions before
remove
all
This may
place the
-
or
Ventilation
fire
cause a
or an
electric shock.
Do not
moving.
-
Do not
any hot
connec-
the
bookcase
across
objects
set in
a
built-in installation such
as a
plug in unit if power cord or plug is damaged
connecting part of the power outlet is loose.
This may
fire
cause a
or an
or
electric shock.
rack.
Dispose of used batteries carefully
eating them.
required.
to
prevent
child
a
from
-
In
case
When
carry
-
of
a
child
eating them,
contact doctor
immediately.
moving the set assembled with speakers
holding the speakers.
This may cause the set to fall, causing serious
adult, and serious damage to the Monitor.
injury to
a
do not
child
or
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
When
installing the set on a table, be careful not
place the edge of its stand on the end of the table.
-
This may cause the set to fall, causing serious
adult, and serious damage to the set.
injury to
a
child
to
or
-
This may
cause
damage
the set
Contact the service centre
internal
-
part
or
could
once
a
give
an
electric shock.
year to clean the
of the set.
Accumulated dust
can cause
mechanical failure.
The distance between eyes and the screen should be
7 times the diagonal length of the screen
approx. 5
~
away.
If not, eyes will strain.
-
Unplug the set from the wall outlet when it is left unattended
long periods of time or in the occurrance of
and unused for
a
-
Do not
place
an
outside antenna in the
head power lines
or
vicinity of overother electric light or power cir-
state of emergency.
Accumulated dust may cause a fire or
deterioration through electric leakage.
an
electric shock from
cuits.
-
This may
cause an
There should be
electric shock.
enough distance between
an
outside
antenna and
touching
-
This may
Do not
-
power lines to keep the former from
the latter even when the antenna falls.
cause an
pull the plug
This may
cause a
electric shock.
not the cord when
disconnecting.
fire.
Owner's Manual
3
Contents
Contents
Contents
Menu
Special
Safety Warnings
Options
ChildLock..................................29
SafetyInstructions..........................2~3
ISM
Introduction
Method
(Image Sticking Minimization)
.
.
.
.
.
.
.
.
.29
LowPower.................................29
RemoteControlKeyFunctions...................6
LocationandFunctionofControls
.
.
.
.
.
.
.
.
.
.
.
.
.
.7~8
Installation
External
Equipment Viewing Setups
DisplayableMonitorSpecification
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.9~13
.
.
.14
HDMI..................................15~16
Accessories.................................17
InstallationOptions...........................18
Demo.................................29
.30
Softwareupdate(InDigitalmodeonly).
Subtitle Language (In Digital mode only)
.31
.31
CIinformation(InDigitalmodeonly).
Screen Menu Options
.32
Autoadjustment(RGB[PC]modeonly).
ManualConfigure............................32
SelectingWideVGAmode.....................32
SettingthePictureFormat.....................33
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PictureSizeZoom...........................33
Operation
TurningontheSet...........................18
Channel Menu Options
Auto Programme Tuning (In Digital mode only)
.19
Auto Programme Tuning (In Analogue mode only)
.19
Manual Programme Tuning (In Analogue mode only)
.20
.20
FineTuning(InAnaloguemodeonly).
.20
Assigning a Station Name (In Analogue mode only)
.21
ProgrammeEdit(InDigitalmodeonly).
.21
Programme Edit (In Analogue mode only)
Favourite Programme (In Digital mode only)
.22
Favourite Programme (In Analogue mode only)
.22
.22
System information (In Digital mode only)
.22
Calling up the Programme Table (In Analogue mode only)
Picture Menu Options
PSM(PictureStatusMemory)..................23
CSM(ColorStatusMemory)....................23
Manual Colour Temperature Control (User option)
.23
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
ScreenPosition..............................34
Cinema....................................34
NR(NoiseReduction).........................34
.34
Initializing (Reset to original factory settings)
PIP (Picture-in-Picture) Feature
WatchingPIP...............................35
.35
ProgrammeSelectionforSubPicture.
.35
Selecting an Input Signal Source for the PIP
MovingthePIP(PIPmodeonly).................35
POP (Picture-out-of-Picture: Channel Scan)
.35
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
PictureSize.................................35
.35
Adjusting PIP Transparency (PIP mode only)
(In Digital mode only)
Teletextwithindigitalservice....................36
Teletextindigitalservice.......................36
Teletext (In Analogue mode only)
.
.
.
.
.
.
Teletext
Switchon/off................................37
SIMPLEText(option).........................37
TOPText(option)............................37
......................................23
sRGB.....................................24
ACM(ActiveColorManagement)................24
FASTEXT..................................38
ManualPictureControl........................24
SpecialTeletextFunctions.....................38
Sound Menu
Options
SSM(SoundStatusMemory)...................25
Miscellaneous
EPG
(Electronic Programme Guide) (In Digital mode only) .39~41
.42~48
ExternalControlDeviceSetup
IRCode(NECFormat).....................49~50
ProgrammingtheRemote..................51
ProgrammingCodes......................52
TroubleshootingChecklist......................54
ProductSpecifications.........................55
BBE.......................................25
.
.
AVL(AutoVolumeLeveler).....................25
AdjustingSoundControl.......................25
TVspeaker.................................26
AudioLanguage.............................26
Stereo/DualReception........................27
NICAMReception(option).....................27
Soundoutputselection........................27
Time Menu Options
.
.
.
.
.
.
.
.
.
.
.
.
.
Currenttime................................28
SettingtheOn/OffTimer.......................28
AutoSleep.................................28
SleepTimer.................................28
Disposal
of your old
appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
by the European Directive 2002/96/EC.
All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
means
2.
After
reading this
manual, keep it in a
place where the user
can refer to easily.
4
PLASMA TV
3.
4.
the
product
is covered
Introduction
Introduction
What is
a
Plasma
If
is
inputted
voltage
Display
to gas in
?
glass panels,
ultraviolet rays
moment, light is emitted. A Plasma Display is
160°
-
Wide
A Plasma
angle range
Display provides
a
next
are
generation
outputted and fused with a fluorescent
flat Display using this phenomenon.
substance. At this
of vision
than 160°
more
angle
range of vision
so
that you
can
get
a
picture
without distortion from
any direction.
Easy
installation
A Plasma
Display is much lighter
place.
and smaller than other
same
class
products
so
that you
can
install the Plasma
Display
in the desired
Big
screen
The
screen
of
a
Plasma
Multimedia Plasma
A Plasma
and
The
Display
can
Display
is 42"
so
that you
can
get vivid experience
as
if you
are
in
a
theater.
Display
be connected with
a
computer
so
that you
can use
it
as a screen
for
conference, game, internet
so on.
explanation
about coloured dots may be present
The PDP which is the
display
device of this
product
is
composed
on
PDP screen
of 0.9 to 2.2 million cells and
in the manufacture of the PDP. Several coloured dots visible
on
the
a
few cell defects
acceptable, in line
PDP manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product
responds to this standard is regarded as acceptable. It means that it could not be changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
occur
screen
would be
can
with other
which
cor-
Trade Mark of the DVB Digital Video
Broadcasting Project (1991 to 1996)
ID
Number(s):
3464: 42PX4DV
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner's Manual
5
Introduction
Remote Control
Control
-
-
When
There
Key
Functions
using the remote control aim it at the remote control sensor of the set.
maybe a defect in consecutive operation of remote control in a specified brightness according
selects
analogue
or
D/A TV
mode.
POWER
switches the set
digital
to this set.
from
on
standby
off to
or
standby.
MODE
Selects another device.
D/A TV
POWER
GUIDE
shows
a
INPUT
Selects the TV, AV, Component, RGB
HDMI modes.
switches the set on from standby.
INPUT
programme schedule.
(In Digital mode only)
DVD
VC R
TV
ARC
PIP
Switches the sub picture on or off.
Selects PIP or DW modes.
PIPPR+/Selects a programme for the sub picture.
SWAP
Alternates between main and sub picture.
PIP INPUT
Selects the input mode for the sub picture.
SIZE
Adjusts the sub picture size.
POSITION
Moves the sub picture to D / E orF/G
direction.
P IP P R+
S WA P
P SM
SSM
PR
-
P IP
SUBTITLE/ *
switches the subtitle
SUB TIT
L E/
G UIDE
Changes
SL EEP
PIP
TEXT
U
MEN
the
on or
off in
Digital
mode.
ARC
PIP
INP
UT
SLEEP
Sets the
the
format.
picture
sleep
timer.
EXI T
SSM
To select the sound
viewing
OK
appropriate
to your
programme.
EXIT
Clears all on-screen displays and returns to
TV viewing from any menu.
PSM
Adjusts
or
factory preset picture according
to the
room.
TEXT
These buttons are used for teletext.
For further details, see the 'Teletext' section.
/
INF
O
MENU
Displays
on screen menus one
by
one.
COLOURED BUTTONS
Exits the current menu.
Memorizes menu changes.
accepts your selection
MUTE
FAV
used for teletext
PR
INFO/
OK
the
current mode.
Selects
Switches the sound
These buttons
are
models)
or
/*
i
(option)
of the
screen
VOL D / E (Volume Up/Down)
Increases/decreases sound level.
PR D / E (Programme Up/Down)
Selects a programme.
settings.
menu
:
TELETEXT
displays information on top
whilst watching the TV.
(In Digital mode only)
/ E orF/G
menu
(only
programme edit.
displays
or
D
Adjusts
VOL
item.
MUTE
off.
on or
LIST
Q.VIEW
FAV
selects
NUMBER buttons
SIZE
POSITION
INDEX
HOLD
TIME
REVEAL
MIX
I/II
LIST
Displays the programme table.
(In Analogue mode only)
a
favourite programme.
Q.VIEW
Returns to the
?
previously viewed
programme.
VCR/DVD BUTTONS
Controls
a
controls
Installing
I/II
Selects the language during dual
broadcast.
Selects the sound output.
LG video cassette recorder.
a
LG DVD
player.
Batteries
?
Open
the
battery compartment cover
polarity.
on
the back side and insert
the batteries with correct
?
Install two 1.5V alkaline batteries of AA
teries with
6
PLASMA TV
new
batteries.
type. Don't mix used bat-
language
Introduction
Location and Function of
of Controls
Controls
<Front Panel Controls>
7
8
INPUT
2
1.
from
Remote Control Sensor
3.
INPUT Button
Selects the
standby
or
off to
on
from
5
standby.
6
D / E
(Programme Up/Down)
Selects
a
programme
or
HDMI modes.
standby.
7.
Exits the current
Memorizes
menu
by
set is turned
one.
on
item.
Power Indicator
Illuminates red in
on screen menus one
or a menu
from
standby.
F / G (Volume Up/Down)
Adjusts the volume.
Adjusts menu settings.
MENU
Displays
PR
Switches the set
TV, AV, Component, RGB
Switches the set
4
VOL
OK
6.
on
2.
5.
3
Power Button
Switches the set
4.
1
MENU
standby mode,
Illuminates green when the
on
menu.
8.
changes.
Intelligent Eye
Adjusts picture according
to the
surrounding
conditions.
OK
Accepts
your selection
or
displays
the current mode.
Owner's Manual
7
Introduction
Location and Function of
of Controls
Controls
-
-
-
Shown is
a
simplified representation
of the set.
What is shown here may be somewhat different from your set.
This manual explains the features available on the 42PX4DV series.
<Back Panel>
V5
S-VIDEO
VIDEO
11
L/MON
AUDIOR
AC INPUT
1
1.
PCMCIA
2
345
(Personal Computer Memory
Association) Card Slot
6
Card
7
8.
ANTENNA INPUT/OUTPUT
3.
HDMI(DVI VIDEO)
output socket of the PERSONAL
Note: If you want to use RGB/DVI audio, we strongly
recommend that you use the cable that has a core, or the
EMI Filter core along with separate cable.
9.
EURO SCART SOCKET
Connect the
REMOTE CONTROL
5.
VARIABLE AUDIO OUT SOCKETS
b. If the
7.
(CONTROL/SERVICE)
port
AUDIO/VIDEO IN SOCKETS
on a
PORT
the
PC.
equipment
S-VIDEO/AUDIO IN SOCKETS
Connect the S-VIDEO out socket of
an
VCR to the S-VIDEO
socket.
Connect the audio out sockets of the VCR to the audio
8
in AV4.
PLASMA TV
operates
on
AC power. The voltage is indicated
page. Never attempt to operate the
on
DC power.
11. AUDIO/VIDEO IN SOCKETS
Connect the audio/video out sockets of external
as
S-VIDEO(Y/C) signal is received through the Euro
(AV2), you must change to the SAV2 mode.
Specifications
Monitor
(AV4)
to these sockets.
sockets
scart socket of the VCR to these sockets.
10. POWER CORD SOCKET
This set
RS-232C INPUT
euro
Note:
a. If you want to use the EURO scart cable, you have to
use the signal shielded Euro scart cable.
scart socket 2
4.
Connect to the RS-232C
outputs to Y, PB, PR of COMPONENT
outputs to Audio sockets of AUDIO
INPUT.
COMPUTER to this socket.
6.
10
COMPONENT INPUT
INPUT and audio
/ AUDIO INPUT / RGB INPUT
Connect the monitor
9
Connect DVD video
International
2.
8
(AV5)
S-VIDEO/AUDIO IN SOCKETS
on
Installation
External
Equipment
V
V iewing
Setups
Setups
Antenna Connection
-
Be careful not to bend the bronze wire when
Apartments
(connecting
to wall antenna
connecting
to
an
antenna
port.
socket)
wall antenna socket
RF coaxial wire
(75 ohms)
<
Back
panel
of the set
>
VHF antenna
UHF antenna
outdoor antenna
Private house
(connecting
When
Audio
-
-
-
-
Connect the VIDEO OUTPUT socket
equipment,
(yellow)
match the colours of
to the VIDEO INPUT
on
connecting ports (Video
-
yellow,
Audio
Or,
a
-
white,
regular
a
VCR
input.
connect the Euro scart socket of the VCR to the Euro scart socket of the set.
Use the Orbiter function to avoid
If
(L)
the set.
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set.
If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting
ture from
-
the Monitor to external
connecting
(R) -red).
to the Video
-
antenna)
VCR
Watching
-
to wall outdoor
4:3
a
VCR.
(Refer
to p.
having
a
fixed
image
remain
on
the
screen
for
a
long period
of time.
Typically
a
frozen still
pic-
29)
picture format is used; the fixed image may remain visible on the screen.
picture noise (interference), leave an adequate distance between the VCR
To avoid
and the set.
<
Back
panel
of the set
>
TV programmes
Turn the set on and select the programme you
Watching
-
want.
Watching
1.
select
-
VCR
Use the INPUT button
on
the remote control to
AV1, AV2, SAV2, AV3, AV4
connected to the S-VHS VCR
only
2.
or
AV5.
If both S-VIDEO and VIDEO sockets have been
the S-VIDEO
Insert
a
video
PLAY button
(See
VCR
can
simultaneously,
be received.
tape into the VCR and press the
on
the VCR.
owner 's
manual)
or
<VCR>
Owner's Manual
9
Installation
External
Watching
Back
<
panel
Equipment
V
V iewing
Setups
Setups
Cable TV
of the set
>
-
After
subscribing
converter you
-
for
can
a
local cable TV station and
installing
a
watch cable TV.
For further information of cable
TV,
contact the local cable TV
station.
To watch cable TV
1.
Use the INPUT button
AV2, SAV2, AV3, AV4
-
the remote control to select AV 1
on
or
,
AV5.
If both S-VIDEO and VIDEO sockets have been connected
to the Cable box
simultaneously, only
the S-VIDEO
can
be
received.
or
2.
Tune the cable
provided
channels
using
the Cable
set-top
box.
or
<
Watching
Cable box
>
DVD
How to connect
1. Connect the DVD video
to the COMPONENT (Y, PB, PR) INPUT jacks on the set and connect the DVD
jacks on the set, as shown in the figure.
If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the set and connect the DVD audio outputs
to the AUDIO INPUT jacks on the set, as shown in the figure.
Note: If your DVD player does not have component video output, use S-Video.
audio
2.
outputs
outputs (Y, PB, PR)
to the AUDIO INPUT
<
How to
use
1.
Turn
2.
Use
3.
Component, AV1, AV2 or AV3.
(If connected to S-VIDEO, select the AV4 or AV5 external
input source.)
Refer to the DVD player's manual for operating instruc-
on
the DVD
INPUT
player,
button
on
and insert
the
a
DVD.
remote
control
to
select
tions.
?
Component Input ports
You can get better picture quality if you
DVD player with component input ports as
Component ports
of the
set
Video
output ports
of DVD
player
YPB
Y
Y
Y
Y
Pb
B-Y
Cb
PB
connect
below.
PR
Pr
R-Y
Cr
PR
or
<
10
PLASMA TV
DVD
player
>
Back
panel
of the set
>
Installation
Watching
<
Back
panel
external AV
of the set
source
>
-
When
the set to
connecting
an
external source,
match the
colours of AUDIO/VIDEO
jacks
=
on
the audio/video
white, Audio (Right)
How to
input jacks on the set with the output
equipment: Video yellow, Audio (Left)
=
=
red.
use
1. Use the INPUT button
on
the remote control to select
AV1, AV2, SAV2, AV3, AV4
2.
See
or
AV5.
corresponding external equipment.
external equipment operating guide.
Operate
the
Camcorder
AUDIO
RL
VIDEO
Video game set
Watching
-
This set
signals
DTV with
can
from
Set-top
box
receive
a
Digital Free to air/Cable signals without an external digital set-top box. However,
digital set-top box or other digital external device, refer to the figure as shown below.
if you do receive
Digital
How to connect
1. Use the monitor's COMPONENT
(Y, PB, PR) INPUT, RGB or
connections, depending on your set-top box
jack
connector. Then, make the corresponding audio connections.
HDMI
How to
1. Turn
the
?
the
digital set-top
digital set-top box.)
2. Use INPUT
on
box.
(Refer to
the
the remote control to select
owner 's
Component,
RGB
or
Digital Set-top
box
Component
RGB
HDMI
o
x
x
/
576p
o
o
o
720p (60Hz)
o
o
o
1080i
o
o
o
480p
manual for
Terminal
480i / 576i
Mode
use
on
from
Input signal
for video
(60Hz)
HDMI.
<
or
HDMI OUTPUT
Back
panel
of the set
>
or
(R)
AUDIO
HDMI OUTPUT
(L)
<
Digital Set-top
(R)
Box
AUDIO
(L)
Y
PBR
P
>
Owner's Manual
11
Installation
External
-
Equipment
Monitor Out
Setup
The set has
special signal output capability
a
a
second TV
or
V
V iewing
Setups
Setups
<
which allows you to hook up
Back
panel
of the set
monitor.
Connect the second TV
or
monitor to the set's EURO SCART SOCKET.
See the
Operating Manual of the second
regarding that device's input settings.
Input
Mode
TV
or
Output
monitor for further details
Mode
SCART 1
AV1 CVBS/RGB
DTV CVBS
SCART 2
AV2 CVBS,
SAV2 Y/C
TV CVBS
SCART 3
AV3 CVBS
Monitor out
Note:
a.
Component, RGB, HDMI input
input sources cannot be
b. HDMI
sources
cannot be used for Monitor out.
used for DTV out.
S-VIDEO
IN
(R)
AUDIO
(L)
VIDEO
Insertion of CI Module
<
Back
panel
of the set
>
-
To view the scrambled
(pay)
services in
Insert the CI Module to PCMCIA
International
For further
TV
12
PLASMA TV
Association)
information,
digital TV mode
(Personal Computer Memory
CARD SLOT of TV
see
p.31.
as
shown.
Card
>
Installation
Connecting
-
-
-
-
-
PC
To
enjoy vivid picture and sound, connect a PC to the set.
keeping a fixed image on the set's screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.
Connect PC to the RGB INPUT(PC INPUT) or HDMI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output
of PC accordingly.
There might be noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode into
another resolution or change the refresh rate into another rate or adjust the brightness and contrast on the menu until the picture
is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card.
The synchronization input waveform for Horizontal and Vertical frequencies are separate.
Avoid
Setup Instructions to Connect a
We recommend using 640x480,
-
-
-
-
-
-
-
-
-
-
-
PC to your set
60Hz for the PC
mode, they provide the best picture quality.
UXGA, there will be no picture on the set.
Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the
HDMI output port of the PC to the HDMI INPUT port on the set.
If the resolution of PC is
over
Connect the audio cable from the PC to the Audio
If
using
a
sound
input on the
required.
Play Solution. The set provides
card, adjust PC sound
This set
set.
(Audio
cables
are
set
or
the
not included with the
signal
cable from the
set).
as
uses a VESA Plug and
EDID data to the PC system with a DDC protocol. The PC adjusts
automatically when using this set.
DDC protocol is preset for RGB (Analog RGB), HDMI (Digital RGB) mode.
If required, adjust the settings for Plug and Play functionally.
If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT or HDMI
INPUT to display the PC on the set.
If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or HDMI ; (the other mode
is set to Plug and Play automatically by the set.)
DOS mode may not work depending on video card if you use a HDMI to DVI cable.
When you use too long RGB-PC cable, there might be a noise on the screen. We recommend using under 5m of the cable. It provides the best picture quality.
<
Back
panel
of the set
>
PC
Setup
1. Turn
on
the PC and
the set.
2. Turn
on
the
POWER button
apply power to
display by pressing the
on
the set's remote control.
3. Use the INPUT button
the RGB
or
HDMI
4. Set the resolution
(1280
x
on
input
the remote control to select
source.
output of the PC to SXGA
1024, 60Hz). (Refer to p. 14)
or
under
Owner's Manual
13
Installation
Displayable
Monitor
RGB / HDMI mode
Resolution
Horizontal
Vertical
Frequency(KHz)
Frequency(Hz)
31.468
70.09
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
35.000
66.66
37.861
72.80
37.500
75.00
43.269
85.00
31.500
60.00
37.799
70.00
39.375
75.00
31.500
60.00
37.799
70.00
39.375
75.00
35.156
56.25
37.879
60.31
48.077
72.18
46.875
75.00
53.674
85.06
49.725
74.55
48.363
60.00
56.476
70.06
60.023
75.02
68.677
85.00
54.348
60.05
63.995
70.01
67.500
75.00
68.681
75.06
60.023
60.02
63.981
60.02
640x350
720x400
640x480
848x480
852x480
800x600
832x624
1024x768
1152x864
1152x870
1280x960
1280x1024
14
PLASMA TV
Specification
Specification
Installation
-
HDMI TM the HDMI
,
and
logo
High-Definition
Multimedia Interface
are
trademarks
or
trademarks of HDMI
registered
Licensing.
-
-
-
This set
receive the
can
High-Definition
Multimedia Interface
(HDMI)
Input
or
of
Digital
Visual
Interface(DVI).
This set
supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play, this
sets the HDMI/DVI
After
Data
source devices automatically.
reading HDMI/DVI source devices, using Display
(EDID) stored in the set is used.
If HDMI/DVI Source devices do not
-
When Source Devices have DVI
(Refer
to <How to
Data Channel
support AUTO HDMI/DVI, the resolution is
Output Connector,
Extended
(DDC) Protocol,
Display
Identification
set
you must connect audio with
manually.
separated cable.
connect>)
How to connect
1. When Source Devices
-
the
-
-
-
(DVD Player or Set Top Box) support HDMI.
Output Connector, Source Devices connect
If Source Devices have HDMI
to the set with HDMI Cable
.(not supplied
with
product).
If Source Devices
support Auto HDMI, automatically, Source Devices divert output resolution in 640x480p. But if not, refer
to the reference Manual of Source Devices and select resolution
manually.
To
Box
get the best picture quality, adjust the DVD Player
Because HDMI sends
Digital
Video and Audio with
or
one
Set
output resolution to 640x480p.
cable, there is no need for a special Audio Cable when using
Top
a
HDMI Cable.
2. When Source Devices
-
with the
-
-
-
to the set with HDMI to DVI Cable
(not supplied
product).
If Source Devices
support Auto DVI, automatically, Source Devices divert output resolution in 640x480p. But if not, refer
to the reference Manual of Source Devices and select resolution
manually.
To
Box
get the best picture quality, adjust the DVD Player
In this case,
Input
use
If PC has
or
Set
Top
output resolution
another cable for audio. When Source Devices have
of the set connect to Audio Cable
3. When PC
-
(DVD Player or Set Top Box) supports DVI.
Output Connector, Source Devices connect
If Source Devices have DVI
(not supplied
with the
product).
Analog
Audio
And then you
to 640x480p.
Output Connector,
can
RGB/DVI Audio
listen to normal Audio.
supports DVI.
a
DVI
Output Connector,
Source Devices connect to the set with HDMI to DVI Cable
(not supplied
with the
product).
-
-
-
-
-
-
To
get the best picture quality, adjust the PC graphics card to 640x480, 60Hz.
(VIDEO) for video connections, depending on your PC
Use the the set's HDMI/DVI
If the
graphics
Input
or
card
HDMI/DVI
on
the PC does not
Input
to
display
connector.
output analog RGB and DVI simultaneously,
the PC
on
connect
only
one
of either RGB
the set.
If the
graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI
Input; (the other mode is set to Plug and Play automatically by the set.)
Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
In this case, use another cable for audio. When PC (or sound card of PC) have Analog Audio Output Connector,
RGB/DVI Audio Input of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to
normal Audio.
Owner's Manual
15
Installation
Reference
Cable
sample
HDMI Cable
(not supplied
with the
Analog
product)
(not supplied
How to
(RCA type)
with the
product)
Analog Audio Cable (Stereo to RCA type)
(not supplied with the product)
HDMI to DVI Cable
with the
Audio Cable
(not supplied
product)
use
1. Connect the HDMI/DVI Source
Devices(DVD Player or Set Top Box or PC) and the set.
display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.
Select HDMI/DVI Input source in Main Input option of PIP/DW menu.
Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness
in HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the
refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC
graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.
2. Turn
3.
4.
on
the
Notes:
-
-
-
-
Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.
keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently
imprinted on the screen. Use the Orbiter screen saver when possible.
When Source Devices are connected with HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size
may not fit to Screen. As shown on page 32, press the MENU button to adjust the screen Position of the set and contact
a PC graphics card service centre.
When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit
EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service
Avoid
centre.
-
In
case
And in
display
16
HDMI/DVI Source Devices Cable is not connected
case
of Video Resolution not
being supported by
or poor cable connection, "No Signal" OSD display will appear.
the set output in HDMI/DVI Source Devices, "No Signal" OSD
will appear. Refer to the Manual of HDMI/DVI Source Devices
PLASMA TV
or
contact your service centre.
Installation
Accessories
D/ATV
INPUT
POWER
DVD
T V
VCR
ARC
S
LEEP
GUDE
INFO
TEXT
EXIT
MENU
OK
VOL
MUTE
SIZE
PR
FAV
LIST
Q.VIEW
UPDATE
NDEX
STILL
TIME
REVEAL
MX
/I
PIPPR-
PPPR+
SWAP
PIP NPUT
PP
PSM
SSM
?
LG TV
AS
mark
Remote Control handset
Owner's Manual
2-Eye
Bolts
1.5V
1 5V
.
Power Cord
Alkaline batteries
Joining
-
the set
Secure the set
assembly
to the wall to
assembly by fixing
it to
a
wall
prevent the
by using
the
2-Wall brackets
set
Eye
tumbling
Bolts/Wall brackets.
If the set is to be mounted on a desk top, insert the 2 Eye-Bolts and tighten them
in the upper holes as shown.
Install the wall brackets on the wall with 2 bolts*, (not supplied with the product),
as shown.
Match the height of the Eye-Bolts and the wall brackets.
?
securely
Check to be
Secure the set
?
Optional
Optional
the
Eye-Bolts
assembly to the
product),
and the brackets
wall with
with the
as
quality improvement.
Without any
(not supplied
-
sure
are
tightened securely.
strong strings
or
wound wire
cables,
shown.
Extras
extras
can
be
changed
or
modified for
notification,
new
optional
extras
can
be
added.
-
Contract your dealer for the
purchasing
of these items.
40
42
40
50 42
Tilt wall
mounting
bracket
Ceiling mounting
bracket
Video cables
Audio cables
Owner's Manual
17
Installation
Installation
?
The set
?
Install this set
can
Options
Options
be installed in different ways such as on a wall, or on a desktop etc.
only in a location where adequate ventilation is available.
Wall Mount: Horizontal Installation
?
The set
can
further
(For
Mounting
be installed
information,
on a
wall
on a
shown above.
refer to the
Bracket Installation and
To Mount
as
Desktop
?
The set
Pedestal Installation
can
be mounted
on a
desk
as
shown above.
'Wall
optional
Setup Guide'.)
Wall
To Install
on a
Desktop
Wall mount minimum allowable clearances for ade-
Pedestal mount minimum allowable clearances for
quate ventilation.
adequate
ventilation.
10cm
3cm
10cm
10cm
10cm
T urning
-
When
using
Turning
on
on
the remote
on
the set
the Set
Set
control, aim it
just after
1. Connect power cord
If the set
18
on
the set
was
Press the r
on
the set.
correctly,
the set is switched to
D
/ E button
on
(power
cord is still
standby
the set
the remote control and then the set will switch
Turning
?
sensor on
installation
2.Pressther/I,INPUTorPR
on
at its
or
mode.
press the
POWER, INPUT, PR
/I,INPUTorPR
D
PLASMA TV
/ E
or
NUMBER buttons
connected)
turned off with the remote control power button and the
/ E button
the remote control to turn the set
D
on.
on.
on
the set
or
press the
r
/ I button
on
POWER, INPUT, PR
the set
D
/ E
or
NUMBER button
Operation
Channel
Channel Menu
Auto
-
mode
Programme Tuning (In Digital
Use this Auto
Programme
to
Options
Options
automatically
1. Press the MENU button and then D
only)
find and store all of the programmes.
/ E
button to select the SETUP
menu.
STATION
2. Press the G button and then D/E button to select Auto programme.
3. Press the G button to select Start.
PICTURE
4. Press the G button to
SOUND
All receivable stations
begin
are
auto
Programme
stored.
stop
programming, press the MENU button.
When auto programming is completed, the Programme edit
See the
'Programme
SPECIAL
SCREEN
PIP/DW
menu
on
appears
Menu
programming
in
Auto programme
viewing.
digital mode,
6
all the stored service informa-
-
Programme Tuning (In Analogue
All stations that
be received
mode
are
stored
1. Press the MENU button and then
use D
can
Pro.
12
27
Menu
Auto
Prev.
the
Edit' section to edit the stored programme.
5. Press the EXIT button to return to normal TV
Note: When you start auto
tion will be deleted.
information
TIME
auto
screen.
Start
G
edit
Favourite programme
System
programming.
The message "All of service-information will be updated. Continue?" will appear.
If you want to keep on auto programming select YES. Otherwise select NO.
To
Auto programme
by
%
Stop
only)
this method. It is recommended that you
use
auto programme
during
installation of this set.
/ E button to select the STATION
2. Press the G button and then D/E button to select Auto programme.
3. Press the G button to select System. Select a TV system with the F / G
4.
L
:
SECAM L/L'
BG
:
PAL
I
:
menu.
STATION
Programme
G
edit
Favourite programme
button;
System
Storage from
BG
2
Start
SOUND
(option)
TIME
B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
PAL I/II (U.K.
Auto programme
Manual programme
PICTURE
/ Ireland /
Hong Kong
Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
Press the E button to select Storage from. Select the beginning programme
with the F / G button or NUMBER buttons on the Storage from menu.
SPECIAL
SCREEN
/ South
PIP/DW
Menu
Prev.
number
5. Press the E button to select Start.
6. Press the G button to
All receivable stations
Note
are
auto
programming.
stored.
:
models, the station name is stored for stations which broadcast VPS (Video
Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as
C (V/UHF 01-69) or S (Cable 01-47), followed by a number.
b. In Australia, if no station name can be assigned to a station, the channel number is
followed by a number see 'Assigning a station name' secassigned and stored as
tion to assign the station name.
a.
In
begin
some
-----
To
stop
programming, press the MENU button.
programming is completed, the Programme edit menu appears
See the 'Programme edit' section to edit the stored programme.
auto
When auto
screen.
on
the
Owner's Manual
19
Operation
Channel
Channel Menu
Manual
-
Options
Options
mode
Programme Tuning (In Analogue
only)
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you
assign a station name with five characters to each programme number.
1. Press the MENU button and then use D / E button to select the STATION
2. Press the G button and then D/E button to select Manual programme.
3. Press the G button to select
/ G
button
or
4. Press the E button to select
L
:
SECAM L/L'
BG
:
PAL
Select the desired programme number with the F
Storage.
NUMBER buttons
on
the
System.
menu.
Storage
Select
I
:
DK
:
PAL
system with the
F / G
button;
(option)
M
:
(USA /
/ Ireland /
Programme
Storage
2
System
BG
G
edit
Favourite programme
Band
V/UHF
SOUND
TIME
Fine
SPECIAL
Search
1
Name
SCREEN
PIP/DW
/ South
Hong Kong
Auto programme
Manual programme
PICTURE
Channel
B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
PAL I/II (U.K.
STATION
menu.
TV
a
can
Africa)
C01
Menu Prev.
D/K, SECAM D/K (East Europe / China / Africa / CIS)
Korea /
Philippines) (option)
5. Press the E button to select Band. Press the F
/ G
button to select V/UHF
or
Cable
as
required.
6. Press the E button to select Channel. You
the F
/ G
button
or
NUMBER buttons. If
select the desired channel number with
can
possible,
select the channel number
directly
with
the number buttons.
7. Press the E button to select Search. Press the F
a
station is found the search will
/ G
button to
commence
searching.
If
stop.
8. Press the OK button to store it.
9. To store another
Fine
-
station, repeat steps
Tuning (In Analogue
Normally
fine
tuning
is
only
mode
3 to 8.
only)
necessary if
reception
is poor.
Repeat the 'Manual programme tuning' steps 1 to 2.
2. Press the G button and then D/E button to select Fine.
1.
3. Press the F
/ G
button to fine tune for the best
picture
finely
tuned programme will be indicated
by
a
Auto programme
Manual programme
PICTURE
Programme
and sound.
yellow
edit
Favourite programme
SOUND
4. Press the OK button.
The
STATION
number
during
programme
a
Station Name
(In Analogue
mode
1
C01
4. Press the D button. You
can use a
blank,
+,
-,
the
alphabet
STATION
Auto programme
Manual programme
PICTURE
Programme
SOUND
TIME
With the E button you
can
select in the
position by pressing
character, and
the
opposite
G
direction.
button and then make your choice of the
SPECIAL
sec-
Storage
2
System
BG
Band
Channel
7. Press the EXIT button to return to normal TV
1
Search
Name
C01
SCREEN
PIP/DW
viewing.
V/UHF
Fine
so on.
6. Press the OK button in twice.
PLASMA TV
edit
Favourite programme
A to Z and the numeric 0 to
9.
5. Select the next
Store
only)
the 'Manual programme tuning' steps 1 to 2.
2. Press the G button and then D/E button to select Name.
3. Press the G button to display the Name menu.
20
V/UHF
Name
SCREEN
viewing.
Repeat
ond
Band
Search
PIP/DW
1.
BG
Fine
SPECIAL
5. Press the EXIT button to return to normal TV
Assigning
2
System
Channel
TIME
selection.
Storage
Prev.
Operation
Programme
-
-
When
Edit
(In Digital
mode
only)
programme number is skipped, it means that you will be unable to select it using PR D / E button during
TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER
buttons or select it in the Programme edit menu.
a
This function enables you to
1. Press the MENU
the stored programmes.
skip
button, then
use
2. Press the G button and then D
3. Press the G
4.
5.
6.
/ E
the D/E button to select the STATION menu.
button to select Programme edit menu.
Programme
edit
16 QVC
button to enter the
Programme edit menu.
Select a programme to be stored or skipped with the D / E or F / G button.
Press the BLUE button repeatedly to have the programme skipped or stored.
In case of programmes to be skipped, skipped programme shows in blue colour and
these programmes will not be selected by the PR D / E buttons during TV viewing.
Press the EXIT button to return to normal TV viewing.
1
2
5
7
15
16
17
23
25
26
27
28
30
32
33
40
51
55
60
70
72
73
74
84
Skip
Menu
FAV
Favourite
Prev.
programme number
programme number to be skipped with the D / E or F / G button.
2. Press the BLUE button. The skipped programme number turns to blue.
Skipping
a
1. Select
a
3. Press the BLUE button
again to release the skipped programme.
programme number is skipped it means that you will be unable to select it
using the PR D / E button during normal TV viewing. If you want to select the skipped
programme, directly enter the programme number with the NUMBER buttons or select
When
a
it in the programme edit or EPG.
4. Press the EXIT button to return to normal TV
viewing.
Selecting favourite programme
Select your favourite programme number by pressing D / E or F / G buttons and then
press the FAV button on your communicator. It will automatically include the selected
programme into your favourite programmes list and a heart-mark will appear in back of
that programme number. You can store up to 10 programmes.
Programme
Edit
(In Analogue
1. Press the MENU
only)
the D/E button to select the STATION
button,
2. Press the G button and then D/E button to select Programme edit.
3. Press the G
Deleting
a
1. Select
a
then
mode
use
button to enter the
Programme
edit
menu.
Programme
0-
menu.
-
-
-
programme to be deleted with the D/E
2. Press the RED button twice.
or
F/G
2C01
7C55
4C05
button.
deleted, all the following programmes
shifted up
are
one
edit
5C05
6C07
3C04
programme
The selected programme is
-
1BLN2
8S27
9S29
Delete
Copy
Move
Skip
Menu
Prev.
position.
Copying
a
1. Select
a
programme
programme to be copied with the D / E or F / G button.
2. Press the GREEN button.
All the following programmes are shifted down one position.
Moving
a
1. Select
programme
programme to be moved with the D/E
2. Press the YELLOW button.
a
or
F/G
button.
3. Move the programme to the desired programme number with the D/E
4. Press the YELLOW button again to release this function.
or
F/G button.
programme number
programme number to be skipped with the D / E or F / G button.
2. Press the BLUE button. The skipped programme number turns to blue.
Skipping
1. Select
a
a
3. Press the OK button.
4. Press the OK button then
use the BLUE button to release the skipped programme.
programme number is skipped it means that you will be unable to select it
the PR D / E button during normal TV viewing. If you want to select the skipped
When
a
programme,
in the
directly
enter the programme number with the NUMBER buttons
programme edit or table menu.
5. Press the EXIT button to return to normal TV
or
using
select it
viewing.
Owner's Manual
21
Operation
Channel
Channel Menu
Favourite
-
Programme (In Digital
Options
Options
mode
only)
This function lets you select your favourite programmes
1. Press the MENU button and then
use
directly.
button to select the STATION
D/E
menu.
2. Press the G button and then D/E button to select Favourite programme.
3. Press the G button to display the Favourite programme menu.
Favourite programme list is displayed.
4. Press the EXIT button to return to normal TV
STATION
Auto programme
PICTURE
Favourite programme
Programme edit
System
3
4
6
9
G
information
SOUND
41
TIME
viewing.
SPECIAL
Repeatedly
press the FAV button to select stored favourite programmes.
SCREEN
PIP/DW
Favourite
Programme (In Analogue
1. Press the MENU button and then
2.
3.
4.
5.
6.
7.
8,
If
E
--
STATION
Auto programme
Manual programme
Programme
PICTURE
edit
Favourite programme
signal strength
is
(In Digital
mode
TIME
Signal strength,
or
Model
name
PIP/DW
Menu
are
displayed.
STATION
Auto programme
Programme
Model
edit
System
information
up the
Programme Table (In Analogue
mode
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
-
-
-
-
-
-
--
by displaying
Menu Prev.
the programme table.
menu.
You may find some blue highlighted programmes shown. They have been set up in the
programme edit mode.
Some programmes with the channel number shown in the programme table indicate
there is no station name assigned.
a programme in the programme table
Select a programme with the D/E or F / G button.
Then press the OK button.
The set switches to the chosen programme number.
Selecting
Paging through
a
programme table
10 programme table pages in which contain 100 programmes.
the D / E or F / G button repeatedly turns the pages.
are
Press the LIST button to return to normal TV
PLASMA TV
viewing.
42PX4DV
3.4.1
Signal strength
Bad
only)
programme table
Press the LIST button to display the Programme table
The programme table appears on the screen.
22
--
-
SOUND
viewing.
check the programmes stored in the memory
Pressing
--
-
-
G
Displaying
There
-
-
-
SW Version
Favourite programme
PICTURE
PIP/DW
?
-
-
-
Prev.
SCREEN
?
-
-
-
SCREEN
SPECIAL
can
-
-
SPECIAL
TIME
You
-
-
antenna.
and Software version
3. Press the EXIT button to return to normal TV
-
0BLN2
-
only)
weak, check the RF cable
1. Press the MENU button and then use D / E button to select the STATION menu.
2. Press the G button and then D/E button to select System information menu.
Calling
FG
SOUND
press the FAV button to select stored favourite programmes.
information
System
Prev.
only)
button to select the STATION menu.
/
Press the G button and then D/E button to select Favourite programme.
Press the G button to display the Favourite programme menu.
Press the D/E button to select
-----.
Select a desired programme with the F / G button or NUMBER buttons. Any number
under 10 is entered with a numeric '0' (or '00') in front of it, i.e. '05' (or '005') for 5.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
Press the OK button.
Press the EXIT button to return to normal TV viewing.
Repeatedly
-
mode
use D
Menu
0-
-
-
-
-
5C05
1BLN2
6C07
2C01
7C55
3C04
8S27
4C05
9S29
Normal
Good
Operation
Picture Menu
PSM
-
-
Status
(Picture
Options
Options
Memory)
This function
adjusts the set to the best picture appearance.
When adjusting picture options (contrast, brightness, colour, sharpness
is automatically changed to User.
and tint
(NTSC input only)) manually,
PSM
1. Press the PSM button
?
Each press of the PSM button
You
?
Picture
?
the
screen
display
as
shown below.
Standard
Dynamic
Intelligent Eye
?
changes
Mild
User
also select Intelligent Eye, Dynamic, Standard, Mild or User in the PICTURE menu.
options Intelligent Eye, Dynamic, Standard and Mild are preset and programmed for good picture
quality at the factory and cannot be changed.
When the eye function is on, the most suitable picture is automatically adjusted according to the surrounding
can
conditions.
CSM
-
(Color
Status
To initialize values
Memory)
(reset
to default
settings),
select the Normal
1. Press the MENU button and then
use
2. Press the G button and then
D/E button to select CSM.
D/E
option.
button to select the PICTURE
menu.
STATION
PSM
CSM
use
use
D/E button to select the desired colour
tempera-
TIME
ture.
Normal
Contrast
Warm
100
Brightness
60
Colour
50
Sharpness
50
User
SPECIAL
4. Press the EXIT button to return to normal TV
?
Each press of D / E button
Cool
You
can
Temperature
adjust red,
green,
or
display
SCREEN
as
shown below.
Warm
Control
PIP/DW
Menu
use D / E
use D / E
3. Press the G button and then
use
button to select the PICTURE
menu.
STATION
button to select CSM.
PSM
F / G button to make
appropriate adjustments.
-
You
Cool
Normal
viewing.
Contrast
Warm
100
Brightness
60
Colour
50
Sharpness
50
User
Red
0
SPECIAL
Green
0
SCREEN
Blue
0
PIP/DW
-
G
ACM
D/E button to select User.
5. Press the EXIT button to return to normal TV
-
0
Prev.
PICTURE
TIME
use
0
Blue
temperature you prefer.
SOUND
4. Press the G button and then
0
User
CSM
2. Press the G button and then
Red
Green
(User option)
blue to any colour
1. Press the MENU button and then
viewing.
screen
Normal
Manual Colour
-
changes
the
Cool
ACM
SOUND
3. Press the G button and then
G
PICTURE
Menu
Prev.
picture with LG's excellent Digital Reality processor technology.
RGB[PC], HDMI[PC] mode.
When selecting picture options (Intelligent Eye, Dynamic, Standard and Mild) in PICTURE menu, XD is automatically
changed to On.
can
enjoy
the vivid and hi-definition
This function is not available for
use
1. Press the MENU button and then
in
use
D/E
button to select the PICTURE
menu.
STATION
PSM
CSM
2. Press the G button and then
use
D/E button to select XD.
use
D/E button to select On
or
Off.
TIME
4. Press the EXIT button to return to normal TV
viewing.
On
Off
ACM
SOUND
3. Press the G button and then
G
PICTURE
Contrast
100
Brightness
60
Colour
50
Sharpness
50
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
23
Operation
Picture Menu
Options
Options
sRGB
When the set is connected to external
-
equal image
This function works in the
-
equipment
with the sRGB
function, the colour difference is adjusted the
of each other.
mode
following
1. Press the MENU button and then
use
:
RGB[PC], HDMI[PC].
button to select the PICTURE
D/E
menu.
STATION
PSM
CSM
2. Press the G button and then
use
PICTURE
D/E button to select sRGB.
sRGB
SOUND
3. Press the G
button and then
use
D/E button to select On
4. Press the EXIT button to return to normal TV
or
Off.
Contrast
G
On
Off
100
Brightness
60
TIME
viewing.
SPECIAL
SCREEN
PIP/DW
ACM
-
-
(Active
Adjust
Color
Menu Prev.
Management)
the ACM to select the desired skin colour
This function is not available for
-I t 's not available to
use
use
in
option.
RGB[PC], HDMI[PC]
mode.
this function in XD Off mode.
1. Press the MENU button and then
button to select the PICTURE
use D / E
menu.
STATION
PSM
CSM
2. Press the G button and then
3. Press the G button and then
use D / E
use
PICTURE
button to select ACM.
F / G button to make
ACM
SOUND
appropriate adjustments.
TIME
4. Press the EXIT button to return to normal TV
viewing.
G
Contrast
100
Brightness
60
Colour
50
Sharpness
50
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Manual Picture Control
-
You
adjust picture contrast, brightness, colour, sharpness and tint (NTSC input only)
use colour, sharpness function in RGB[PC], HDMI[PC] mode.
broadcasting system PAL/SECAM, the picture item Tint doesn't work.
can
to the levels you
prefer.
-I t 's not available to
-
In the
1. Press the MENU button and then
use
button to select the PICTURE
2. Press the G button and then
use
D/E button to select the desired
3. Press the G button and then
use
F / G button to make
D/E
menu.
STATION
PSM
CSM
4. Press the EXIT button to return to normal TV
viewing.
picture option.
PICTURE
ACM
SOUND
Contrast
Brightness
60
TIME
Colour
50
Sharpness
50
appropriate adjustments.
SPECIAL
SCREEN
PIP/DW
24
PLASMA TV
Menu Prev.
100
G
Fleshtone
0
Greentone
0
Bluetone
0
Operation
Sound
Sound Menu
SSM
-
-
Status
(Sound
Options
Options
Memory)
This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the SSM button.
2. Press the SSM button to select your desired sound.
SRS TSXT
Flat
Music
?
You
?
The sound SRS TSXT, Flat, Music, Movie and
cannot be changed.
Movie
User
Sports
also select SRS TSXT, Flat, Music, Movie,
can
Sports or User in the SOUND menu.
Sports are programmed for good sound reproduction
at the
factory
and
R
is
-
-
a
trademark of SRS
TruSurround XT
technology
is
Labs, Inc.
incorporated
under license from SRS
Labs, Inc.
BBE
-
BBE
High
Definition Sound restores
1. Press the MENU button and then
clarity
use
and presence for better
speech intelligibility
D/E button to select the SOUND
menu.
and musical realism.
STATION
SSM
PICTURE
AVL
G
BBE
2. Press the G
button and then
3. Press the G button and then
use
use
D/E button to select BBE.
D/E button to select On
4. Press the EXIT button to return to normal TV
or
viewing.
0
SOUND
Treble
50
Bass
50
TIME
TV
Off.
On
Off
Balance
Speaker
SPECIAL
SCREEN
Manufactured under license from BBE
AVL
-
(Auto
Volume
Sound, Inc.
PIP/DW
Menu
Prev.
Leveler)
This feature maintains
an
equal
volume
1. Press the MENU button and then
level;
use
even
if you
change
channels.
D/E button to select the SOUND
menu.
STATION
SSM
PICTURE
AVL
SOUND
Treble
50
Bass
50
BBE
2. Press the G button and then
3. Press the G button and then
use D / E
use D / E
button to select AVL
button to select On
or
Balance
Off.
TIME
4. Press the EXIT button to return to normal TV
G
.
viewing.
TV
0
On
Off
Speaker
SPECIAL
SCREEN
PIP/DW
Adjusting
Menu
Prev.
Sound Control
1. Press the MENU button and then
use
button to select the SOUND
D/E
menu.
STATION
SSM
PICTURE
AVL
SOUND
Treble
BBE
2. Press the G button and then
3. Press the G
use
D/E button to select the desired sound item.
button and then use F / G button to make
4. Press the EXIT button to return to normal TV
appropriate adjustments.
viewing.
Balance
Bass
TIME
TV
0
50G
50
Speaker
SPECIAL
SCREEN
Note
:
Treble, Bass
or
BBE aren't suitable for
use
with SRS TSXT.
PIP/DW
Menu
Prev.
Owner's Manual
25
Operation
Sound
Sound Menu
TV
-
-
Speaker
You
In
can
adjust
the internal
speaker
status.
COMPONENT, RGB[PC] and HDMI[PC] mode, TV speaker and/or variable audio
there is
-
Options
Options
no
video
If you want to
can
be
outputted
even
though
signal.
use
your external hi-fi stereo
1. Press the MENU button and then
system,
use D / E
turn off the internal
speakers
button to select the SOUND
of the set.
menu.
STATION
SSM
PICTURE
AVL
SOUND
Treble
50
Bass
50
BBE
2. Press the G button and then
use D
3. Press the G button and then
use
/ E
button to select TV
D/E button to select On
Speaker.
or
Balance
Off.
TIME
4. Press the EXIT button to return to normal TV
TV
0
G
Speaker
On
Off
viewing.
SPECIAL
SCREEN
PIP/DW
Audio
-
-
Language (In Digital
mode
only)
This function lets you select your preferred language for audio.
If the audio data in selected language is not broadcasted, English audio will be
1. Press the MENU button and then
Menu Prev.
use
D/E button to select the SOUND
played.
menu.
STATION
SSM
PICTURE
AVL
SOUND
Treble
50
Bass
50
BBE
2. Press the G button and then
use D
3. Press the G button and then
use
When two
or more
with the I/II button
audio
on
/ E
button to select Audio
D/E button to select
languages
are
language
Welsh
English,
broadcasted, you
can
or
menu.
Balance
Gaelic.
TIME
select audio
language
TV
language
26
PLASMA TV
PIP/DW
G
Welsh
Gaelic
SCREEN
viewing.
English
speaker
Audio
SPECIAL
the remote control.
4. Press the EXIT button to return to normal TV
0
Menu Prev.
Operation
Stereo / Dual
-
When
station
Reception
programme is
a
On Screen
selected, the sound information for the station appears after the programme number and
disappear.
name
Display
Press the I/II button to received broadcast state.
Broadcast
On
Mono
MONO
Stereo
STEREO
Dual
DUAL I
screen
Display
Mono Sound Selection
In stereo
reception
reception if the stereo signal is weak, you can switch to mono by pressing the
the depth of sound is improved. To switch back to stereo, press the I/II button
Language Selection
If
for Dual
Language Broadcast
(dual language),
programme received in two languages
pressing the I/II button repeatedly.
a
switch to DUAL I, DUAL II
or
DUAL I
+
II
by
primary broadcast language to the loudspeakers.
secondary broadcast language to the loudspeakers.
sends a separate language to each loudspeaker.
DUAL I
?
DUAL II sends the
?
DUAL I
+
II
Reception
If your Plasma
Instantaneous
Sound
can
mono
again.
sends the
?
NICAM
-
you
I/II button twice. In
twice
output
Display is equipped with the PDP Tuner for NICAM reception,
Companding Audio Multiplex) digital sound can be received.
can
be selected
according
to the
type of received broadcast
as
the
high quality
follows
NICAM
by pressing
(Near
the I/II button
repeatedly.
?
When NICAM
?
When NICAM stereo is
switch to FM
?
When NICAM dual is
Sound
In
received, you can select NICAM MONO or FM MONO.
received, you can select NICAM STEREO or FM MONO. If the
signal
is
weak,
select NICAM DUAL I, NICAM DUAL II, NICAM DUAL I
display MONO appears on the screen.
+
II,
received, you
mono
can
is selected the
or
HDMI
mode, you
can
select
press the I/II button to select the sound
Audio
output sound for the left and right loudspeakers.
output.
from audio L
input
?
from audio L
?
from audio R
input is sent to left and right loud-speakers.
input is sent to left and right loud-speakers.
L+R
or
output selection
AV, Component, RGB
Repeatedly
signal
right loud-speaker.
L+L : Audio signal
R+R : Audio signal
?
stereo
mono.
MONO. When FM
-
is
mono
:
is sent to left
loud-speaker
and audio
signal
from audio R
input
is sent to
Owner's Manual
27
Operation
T ime Menu
Options
Options
Current time
-
-
When you select 'Auto Clock On', the time is set automatically from
digital channel signal includes information for the current time
The
a digital channel signal.
provided by the
station.
broadcasting
STATION
Auto Clock
GOn
Off
Manual Clock
PICTURE
Off time
On time
SOUND
1. Press the MENU button and then
2. Press the G button and then
use D
use D
/ E button to select the TIME
use D
/ E button to
adjust
the Year.
4. Press the G button and then
use D
/ E button to
adjust
the Date.
5. Press the G button and then
use D
/ E button to
adjust
the Time.
sleep
TIME
/ E button to select the Manual clock
3. Press the G button and then
Auto
menu.
menu.
SPECIAL
SCREEN
PIP/DW
STATION
Menu Prev.
Auto Clock
Manual Clock
6. Press the EXIT button to return to normal TV
viewing.
PICTURE
G
On time
SOUND
Year
2005
Off time
Auto
sleep
Date
01
:
20
Time
16
:
11
TIME
SPECIAL
SCREEN
PIP/DW
Setting
-
-
-
Menu Prev.
the On/Off Timer
The off timer
automatically
switches the set to
standby at the preset time.
they are set to the same time.
Off Timer function overrides
on
The set must be in
mode for the On Timer to work.
standby
Timer function if
1. Press the MENU button and then
use D
/ E button to select the TIME
menu.
STATION
Auto Clock
Manual Clock
2. Press the G button and then
3. Press the G button and then
use D
use D
/ E button to select Off time
On time.
or
PICTURE
Off time
SOUND
Auto
On time
/ E button to select On.
sleep
G
On
Off
12
:
00
TIME
4. Press the G button and then
use D
/ E button to
adjust
Volume
the hour.
Pr.
5. Press the G button and then
6.
Only
On time
use D
function; Press the
gramme number
or
/ E button to
G
button and then
-
To cancel
Off/On
-
Once the
Auto
-
a
on or
use D
SCREEN
/ E button to
adjust
pro-
PIP/DW
Menu Prev.
viewing.
time function
Press the D / E button to select Off in
Two hours after the set is switched on
mode unless
the minute.
volume level.
7. Press the EXIT button to return to normal TV
-
adjust
button has been
step
3.
the
by
pressed.
on
off time is set, these functions
time function it will
operate daily
at the
automatically
switch back to
standby
preset time.
Sleep
If there is
no
input signal,
the monitor turn off
1. Press the MENU button and then
use D
automatically
after 10 minutes.
/ E button to select the TIME
menu.
STATION
Auto Clock
Manual Clock
2. Press the G
button and then
3. Press the G button and then
use D
/ E button to select Auto
sleep.
PICTURE
/ E button to select On
or
Off time
On time
SOUND
use D
Off.
Auto
sleep
viewing.
SPECIAL
SCREEN
PIP/DW
Sleep
-
-
Menu Prev.
Timer
timer turns the set off at the preset time.
zz
Press the SLEEP button to select the number of minutes. The display
Min will appear on the screen,
followed by 10, 20, 30, 60, 90, 120, 180 and 240 minutes. The timer begins to count down from the number
of minutes selected.
Sleep
---
To check the remaining sleep time, press the SLEEP button once.
b. To cancel the sleep time, repeatedly press the SLEEP button until the display
c. If you turn the set off after setting the sleep timer, the setting will be erased.
a.
28
PLASMA TV
GOn
Off
TIME
4. Press the EXIT button to return to normal TV
30
SPECIAL
zz
---
Min appears.
TV
1
Operation
Special
Special
Menu
Options
Options
Child Lock
-
The set
can
be set up
so
that it
can
be used with the remote control.
only
1. Press the MENU button and then D / E button to select the SPECIAL
menu.
STATION
Child lock
GOn
Off
ISM Mwthod
2. Press the G button and then D
/ E button to select Child lock.
3. Press the G button and then D / E button to select On
or
PICTURE
Set ID
SOUND
Off.
Demo
Software
TIME
4. Press the EXIT button to return to normal TV
Low power
Subtitle
update
language
CI information
viewing.
SPECIAL
SCREEN
-
-
This set is programmed to remember which option it was last set to even if you turn
the set off.
In Child lock 'On', if the set is turned off, press the INPUT, PR D/E button on
the set or POWER, D/A TV, INPUT, PR D/E or NUMBER buttons on the remote
control.
With the Child lock On, the display
Child lock on' appears on the screen if
any button on the front panel is pressed while viewing the set.
PIP/DW
Menu
Prev.
'
-
ISM
-
Method
(Image Sticking Minimization)
A frozen of still
picture
image remaining even
a long period of time.
from a PC/video game displayed on the screen for prolonged periods will result in a ghost
when you change the image. Avoid allowing a fixed image to remain on the set's screen for
1. Press the MENU button and then
use D / E
button to select the SPECIAL
menu.
STATION
Child lock
ISM Method
2. Press the
G
button and then
D / E
button to select ISM Method.
PICTURE
3. Press the G button and then D/E button to select either Normal, White wash,
Orbiter or Inversion. If you unnecessary to set this function, set Normal.
Normal
White wash
Orbiter
SOUND
Inversion
Demo
Software
TIME
G
Low power
Set ID
Subtitle
update
language
CI information
White wash:
White wash removes permanent images from the screen.
Note: An excessive permanent image may be impossible to clear entirely with White
Wash.
?
Orbiter:
Orbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen will move every 2 minutes.
?
Inversion:
This is the function to invert the panel color of the screen. The panel color is
automatically inverted every 30 minutes.
?
4. Press the EXIT button to return to normal TV
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
viewing.
Low Power
-
This is the function to reduce the power
1. Press the MENU button and then
consumption
use D / E
of the set.
button to select the SPECIAL
menu.
STATION
Child lock
ISM Mwthod
2. Press the G button and then
3. Press the G button and then
button to select Low power.
D/E
use
PICTURE
Low power
SOUND
use
D/E button to select On
or
Off.
Off
Demo
Software
TIME
4. Press the EXIT button to return to normal TV
GOn
Set ID
Subtitle
update
language
CI information
viewing.
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Demo
Use it to see the difference between XD demo on and XD Demo off.
-I t 's not available to use this function in RGB[PC], HDMI[PC] mode.
-
1. Press the MENU button and then
use
D/E button to select the SPECIAL
menu.
STATION
Child lock
ISM Mwthod
2. Press the G button and then
3. Press the G button to
use
D/E
button to select XD Demo.
PICTURE
stop
XD
Demo
SOUND
begin
XD Demo.
Software
TIME
4. To
Low power
Set ID
Demo, press the EXIT button.
Subtitle
G
To start
update
language
CI information
SPECIAL
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
29
Operation
Special
Special
Software
-
Software
Menu
update (In Digital
Update,
means
Options
Options
mode
software
can
1. Press the MENU button and then
only)
be downloaded
use
through
the
terrestrial
digital
D/E button to select the SPECIAL
broadcasting system.
menu.
STATION
menu.
PICTURE
Child lock
ISM Mwthod
2. Press the G button and then
3. Press the G button and then
If you select Manual,
new software is found.
?
use
D/E
use D / E
a user
button to select Software
button to select Manual
confirm message box will be
update
SOUND
Auto.
or
displayed
to
Low power
Set ID
Demo
Software
notify
TIME
that
Subtitle
update
language
G
Manual
Auto
CI information
SPECIAL
If you select Auto, software will be updated automatically, and you will not be asked
whether you accept the update or not. And progress bar will be displayed automatically.
?
4. Press the EXIT button to return to normal TV
SCREEN
PIP/DW
Menu Prev.
viewing.
When
-
?
?
?
?
setting "Software Update- Manual"
During Progress of Software Update, please
The power of the set must not be
The set must not be switched off.
note the
following:
interrupted.
The antenna must not be disconnected.
During
this time, you should not switch off the power
time, you should not work power On/Off.
?
At this
?
After Software
Update,
you
can
confirm the
updated
to the set.
software version in
System
information
Occasionally, a transmission of updated digital
result in the following menu on the TV screen.
Select the YES
using
menu.
software information will
the F/G button and when you
see
the
following
picture.
After Software
to restart.
30
PLASMA TV
Update
is
completed,
the
System
takes about
one
minute
Operation
Subtitle
-
-
Language (In Digital
If the subtitle data in selected
Use this function when two
mode
language
only)
is not
subtitle
or more
1. Press the MENU button and then
broadcasted, English subtitle will be displayed.
languages
use D / E
are
broadcasted.
button to select the SPECIAL
menu.
STATION
Child lock
ISM Mwthod
2. Press the G button and then
3. Press the G button and then
use D / E
button to select Subtitle
language
menu.
PICTURE
SOUND
D/E
use
button to select
English,
Welsh
or
Gaelic.
4. Press the EXIT button to return to normal TV
or more
subtitle
with the SUBTITLE/ *
CI
-
-
-
-
-
-
[Common Interface]
on
languages
are
(In Digital
select Subtitle
language
G
Welsh
Gaelic
SCREEN
PIP/DW
mode
English
language
SPECIAL
can
the remote control.
Information
update
Subtitle
CI information
viewing.
broadcasted, you
Demo
Software
TIME
When two
Low power
Set ID
Menu
Prev.
only)
This function enables you to watch some scrambled services (pay services).
If you remove the CI Module, you can't watch the pay services.
When the module is inserted to CI slot, you can access the module menu.
To purchase a module and smart card, contact your supplying dealer.
Do not often insert or remove a CAM module from the set. It may cause a trouble.
When the set turned on after inserting the CI Module, you often can't hear the sound.
1. Press the MENU button and then
use D / E
button to select the SPECIAL
menu.
STATION
Child lock
ISM Mwthod
2. Press the G button and then use D/E
button to select CI information
menu.
PICTURE
Low power
Set ID
SOUND
3. Press the G button and then OK button.
4. Press the D/E button to select the desired item: Module
information, language, or software download etc.
information,
smart card
Subtitle
update
language
CI information
G
Module
SPECIAL
SCREEN
5. Press the OK button.
PIP/DW
6. Press the EXIT button to return to normal TV
Demo
Software
TIME
viewing.
Menu
Prev.
Main Menu
?
?
This OSD is
only for illustration and the menu options
vary according to the Digital pay services provider.
It's possible for you to change CI (Common Interface)
vice by your dealer.
and
screen
format will
Module information
Smart card information
menu screen
and
ser-
Language
software download
Press OK to
select,
or
Exit to
quit
Owner's Manual
31
Operation
Screen
Screen Menu
Auto
-
Options
Options
mode
adjustment (RGB [PC]
Automatically adjusts picture position
1. Press the MENU button and then
only)
and minimizes
image shaking.
/ E button to select the SCREEN
use D
menu.
STATION
Auto
config.
Manual
2. Press the G button and then
use D
3. Press the G button to start Auto
button to select Auto
/ E
?
4. If
needs to be
the Manual config..
picture
adjusted
more
-
Although
after Auto
Manual
-
-
-
on screen.
SOUND
Zoom +/-
TIME
Cinema
NR
adjustment again.
adjustment
in RGB
SPECIAL
(PC),
you
adjust
can
Reset
SCREEN
PIP/DW
Menu Prev.
viewing.
the
The Auto
To set
Position
5. Press the EXIT button to return to normal TV
-
G
config.
VGA Mode
ARC
config..
When Auto config. has finished, Ok will be shown
If the position of the image is still not correct, try Auto
?
config..
PICTURE
image is still not correct, your set is functioning properly
config. functions don't need to be run for HDMI mode.
but needs further
adjustment.
Configure
If the
picture
manually.
isn't clear after auto
To correct the
screen
adjustment
and
especially
if characters
are
still
trembling, adjust
the
picture phase
size, adjust Clock.
This function works in the
following
mode
:
RGB[PC], RGB[DTV],
COMPONENT
(480p/576p/720p/1080i),
HDMI
(480p/576p/720p/1080i).
-I t 's not available to
use
Phase, Clock function in RGB[DTV], COMPONENT (480p/576p/720p/1080i), HDMI
(480p/576p/720p/1080i)
mode.
1. Press the MENU button and then D / E button to select the SCREEN
menu.
STATION
Auto
config.
Manual
2. Press the G button and then D / E
button to select Manual
3. Press the G button and then D / E button to select
Position.
PICTURE
config..
Phase, Clock, H-Position
or
V-
SOUND
Selecting
-
-
To
see a
0
Zoom +/-
0
H-Position
Cinema
0
V-Position
0
NR
Reset
SCREEN
viewing.
PIP/DW
Menu Prev.
Wide VGA mode
normal
picture,
match the resolution of RGB mode and selection of VGA mode.
This function works in the
mode:
following
1. Press the MENU button and then
RGB[PC], HDMI[PC]
use D / E
mode
button to select the SCREEN
menu.
STATION
Auto
config.
Manual
2. Press the G button and then
3. Press the G button and then
use
D/E button to select VGA Mode.
PICTURE
SOUND
use
D/E button to select the desired VGA resolution.
4. Press the EXIT button to return to normal TV
viewing.
config.
VGA Mode
848x480
852x480
Cinema
Reset
SCREEN
PIP/DW
PLASMA TV
640x480
Zoom +/-
NR
SPECIAL
G
ARC
Position
TIME
32
Phase
Clock
Position
TIME
appropriate adjustments.
5. Press the EXIT button to return to normal TV
G
ARC
SPECIAL
4. Press the F / G button to make
config.
VGA Mode
Menu Prev.
Operation
the Picture Format
Setting
-
You
can
watch the
screen
in various
picture formats; Spectacle,
Full
(option), Original, 4:3,
16:9
14:9
(Wide),
and Zoom.
1. Press the MENU button and then
use D
/ E button to select the SCREEN
menu.
STATION
Auto
config.
Manual
2. Press the G button and then
use D
3. Press the G button and then
14:9
Original, 4:3, 16:9,
or
use
/ E button to select ARC.
button to select
D/E
PICTURE
ARC
SOUND
Spectacle,
Full
(option),
TIME
Zoom.
Spectacle
Full
4:3
16:9
14:9
Reset
adjust
the
picture
PIP/DW
Prev.
Menu
(option)
adjust
fully.
the
picture
Original
When your TV receives the wide
picture format to be sent.
?
Full
Original
Cinema
SCREEN
When your TV receives the wide screen signal, when selected it will
horizontally or vertically, in a linear proportion, to fill the entire screen
?
Spectacle
Position
Zoom
When your TV receives the wide screen signal, when selected it will
horizontally, in non-linear proportion, to fill the entire screen.
?
G
Zoom +/-
NR
SPECIAL
?
config.
VGA Mode
signal,
screen
it will be
automatically changed
to the
4:3
Following
gray bars
selection will lead you to view
at both the left and
appearing
16:9 (Wide)
Following selection
a picture with
right sides.
original
an
4:3
aspect ratio, with
?
to fill the entire
?
will lead you to adjust the picture horizontally, in
(useful for viewing 4:3 formatted DVDs).
a
linear
proportion,
screen
14:9
You
can
enjoy
mode. The
the
screen
picture
format of 14:9
14:9 is viewed
just
or
general
like that the
TV programme through the 14:9
4:3 is magnified to the left /
screen
right.
?
Zoom
Following
the entire
selection will lead you to view the picture without any alternation, while filling
However, the top and bottom portions of the picture will be cropped.
screen.
4. Press the EXIT button to return to normal TV
-
-
-
-
You
can
You
can
viewing.
only select 4:3 and 16:9 (Wide) in RGB[PC], HDMI[PC] mode only.
only select 4:3, 16:9 (Wide) and Zoom in RGB[DTV], HDMI[DTV], Component [DTV] mode only.
You can only select Spectacle, Full, 4:3, 16:9 (Wide), 14:9 and Zoom in Component [480i/576i] mode only.
There might be uncomfortable in full mode. Then change into other mode.
Picture Size Zoom
-
When
enlarging
or
reducing
the
picture,
the
screen
may be
display
an
unnatural
1. Press the MENU button and then D / E button to select the SCREEN
menu.
looking picture.
STATION
Auto
config.
Manual
2. Press the G button and then D / E button to select Zoom
3. Press the G button and then F / G button to make
+/-.
appropriate adjustments.
PICTURE
ARC
SOUND
viewing.
Zoom +/Position
TIME
4. Press the EXIT button to return to normal TV
config.
VGA Mode
100
G
F
%
G
Cinema
NR
SPECIAL
Reset
SCREEN
PIP/DW
Menu
Prev.
Owner's Manual
33
Operation
Screen
Screen Menu
Options
Options
Screen Position
-
This function is available after
adjusting
Zoom +/-.
1. Press the MENU button and then D / E button to select the SCREEN
menu.
STATION
Auto
config.
Manual
2. Press the G button and then D / E button to select Position.
3. Press the G button and then D / E
or
F / G button to
4. Press the EXIT button to return to normal TV
adjust
PICTURE
config.
VGA Mode
ARC
the
position.
SOUND
Zoom +/-
TIME
Cinema
Position
D
G
F
G
E
NR
viewing.
SPECIAL
Reset
SCREEN
PIP/DW
Menu Prev.
Cinema
-
-
When you watch the movie, this function adjusts the set to the best
This function works in the following mode:
TV, AV1, AV2, AV3, AV4, AV5, SAV2
or
1. Press the MENU button and then
picture
appearance.
COMPONENT 480i/576i.
button to select the SCREEN
use D / E
menu.
STATION
Auto
config.
Manual
2. Press the G button and then
use D
/ E button to select Cinema.
3. Press the G button and then
use D
/ E button to select On
4. Press the EXIT button to return to normal TV
or
PICTURE
config.
VGA Mode
ARC
SOUND
Zoom +/-
TIME
Cinema
Off.
Position
G
SPECIAL
On
Off
NR
viewing.
Reset
SCREEN
PIP/DW
NR
-
Menu Prev.
(Noise Reduction)
You
can
select 3D NR
or
MPEG NR to reduce the
picture
noise which may appear
on
the
screen
during watching
the TV.
-
-
This function is not available for
3D NR is not available for
use
in
use
in
mode.
RGB[PC], HDMI[PC]
RGB, HDMI, COMPONENT[DTV] mode.
1. Press the MENU button and then
use
D/E
button to select the SCREEN
menu.
STATION
Auto
config.
Manual
2. Press the G button and then
3. Press the G button and then
use D / E
button to select NR.
PICTURE
ARC
SOUND
use
D/E button to select 3D NR
or
MPEG NR.
Zoom +/Position
TIME
4. Press the EXIT button to return to normal TV
config.
VGA Mode
Cinema
NR
viewing.
SPECIAL
G
3D NR
0
MPEG NR
0
Reset
SCREEN
PIP/DW
Initializing (Reset
This function
to
operates in
To initialize the
adjusted
Menu Prev.
original factory settings)
current mode.
value
1. Press the MENU button and then D / E button to select the SCREEN
menu.
STATION
Auto
config.
Manual
2. Press the G button and then D / E button to select Reset.
3. Press the G button.
?
You
sub
can
initialize
picture
PICTURE
ARC
SOUND
Zoom +/-
TIME
Cinema
SPECIAL
Reset
Position
Position, Zoom +/-, PIP size, PIP position, PIP Transparency and
size of twin
picture.
NR
SCREEN
PIP/DW
34
PLASMA TV
config.
VGA Mode
Menu Prev.
G
To set
Operation
PIP
(Picture-in-Picture)
(Picture-in-Picture) Feature
PIP lets you view 2 different inputs (sources) on your set screen at the
-I t 's not available to use this function in TELETEXT mode.
-
Watching
time.
PIP
Press the PIP button to show the sub
Each press of PIP button
?
same
changes
picture.
the
display
screen
as
shown below.
RGB
AV1
RGB
RGB
AV1
AV1
10:30
10:30
10:30
RGB
AV1
10:30
Note
:
a.
When the sub
b.
The motion of the sub
picture size is 1/2 of the main picture, the picture quality may decrease.
picture can be unnatural because the set displays full screen by synchronizing the main picture source
rate between the main picture source and the sub picture source is different in PIP mode.
the refresh
Programme
Selection for Sub Picture
Press the PIP PR
+
/- button to select
a
Moving
programme for the sub
picture.
the PIP
(PIP
mode
when
only)
Press the POSITION button.
press the D / E
button until desired
Repeatedly
or
Selecting
an
Input Signal
F / G
position is achieved. The sub
picture moves up/down or
left/right.
Source for the PIP
Win.
position
D
FG
E
Press the PIP INPUT button
to select the
input
picture.
the sub
In
some
source
for
RGB
AV1
10:30
models, when the
sub
for
picture quality get poor
sub picture, select Auto,
PAL, SECAM
PIP
System
or
NTSC in
Picture Size
menu.
Press the SIZE button and
then F / G button to
the sub
POP
(Picture-out-of-Picture:
Channel
Scan)
of all
picture source remains the current channel). The pictures
the programmed channels are searched with the 3 POP
DW2
DW1,
modes, main and sub
picture is adjusted
simultaneously. With
button in PIP
picture
screen.
Adjusting
PIP
Transparency (PIP
mode
adjust
size.
With SIZE button in
Use POP to search the programmes of all the memorized
channels one-by-one on the 3 PIP screen display, (while the
main
picture
is
Win. size
F
G
SIZE
mode, sub
adjusted.
only)
1. Press the MENU button and then D / E button to select the PIP/DW
menu.
2. Press the G button and then D / E button to select PIP
Transparency.
3. Press the G button and then F / G button to
adjust
transparency.
4. Press the EXIT button to return to normal TV
viewing.
PIP
Owner's Manual
35
Operation
Teletext
eletext
The set
gives
you
(In
(In Digital mode)
digital
teletext which is
greatly improved
be accessed
by special digital
teletext services and
access
to
a
in various
aspects such
text, graphics and
as
so on.
This
digital
teletext
can
services which broadcast
specific
digital
teletext.
Teletext within
Press the numeric
To know which
are
digital
or
PR D / E button to select a digital service which broadcasts
teletext services, refer to the EPG service list.
Follow the indications
teletext
digital
Teletext in
on
digital
Press the TEXT
or
or
on
digital
or
move
a
step by pressing TEXT, OK,
D
/ E
,
F / G,
RED,
so on.
different service
on
by
the numeric
or
PR D / E button.
a
certain service which broadcasts
access
digital
teletext.
teletext.
teletext and
color button to switch off
PLASMA TV
onto the next
onto the next
move
NUMBER buttons and
Some services may allow you to
36
teletext.
service
color button to switch
Follow the indications
or
teletext and
NUMBER buttons and
PR D / E button to select
GREEN, YELLOW, BLUE
Press the TEXT
or
service, just select
digital
Press the numeric
digital
digital
GREEN, YELLOW, BLUE
To exit
service
digital
step by pressing OK,
so on.
teletext and return to TV
text services
by pressing
viewing.
the red button.
D
/ E
,
F
/ G
,
RED,
Operation
Teletext
eletext
-
Teletext
(or TOP text)
(In
(In Analogue mode)
is
an
optional function,
therefore
only
the set with the teletext
system
can
receive the teletext
broadcast.
-
-
Teletext is
a
free service broadcast
by
most TV stations which
gives up-to-the-minute
television programmes, share prices and many other topics.
The teletext decoder of this set can support the SIMPLE, TOP and FASTEXT
consists of
information
on
weather,
news,
systems. SIMPLE (standard teletext)
number of pages which are selected by directly entering the corresponding page number. TOP and
FASTEXT are more modern methods allowing quick and easy selection of teletext information.
a
Switch on/off
Press the TEXT button to switch to teletext.
?
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time
are
displayed
on
the
number indicates your selection, while the second shows the current page
Press the TEXT button to switch off teletext.
SIMPLE Text
Page
headline. The first page
(option)
selection
1. Enter the desired page number
as a
three
digit
number with the NUMBER buttons. If
press a wrong number, you must complete the three
2. The PR D / E button can also be used to select the
TOP Text
The
screen
displayed.
digit number and then
preceding or following
selection you
page.
(option)
four fields-red, green, yellow and blue at the bottom of the
denotes the next group and the blue field indicates the next block.
user
during
reenter the correct page number.
guide displays
screen.
The
yellow
field
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the
proceed to the next group with automatic overflow to the next block.
can proceed to the next existing page with automatic overflow to the next
(Alternatively the PR D button can be used.)
The red button permits to return to previous selection. (Alternatively the PR E button can be used.)
yellow
button to
3. With the green button you
4.
Direct page selection
to the SIMPLE text mode, you
NUMBER buttons in TOP mode.
Corresponding
can
select
a
page
by entering
it
as a
three
digit
number
group.
using
the
Owner's Manual
37
Operation
Teletext
eletext
(In
(In Analogue mode)
FASTEXT
The teletext pages are colour coded
corresponding coloured button.
along
the bottom of the
screen
and
are
selected
the
by pressing
Page selection
1. Press the
i
button to select the index page.
select the pages which are colour coded along the bottom line with the same coloured buttons.
3. Corresponding to the SIMPLE text mode, you can select a page by entering its three digit page number
with the NUMBER buttons in FASTEXT mode.
2. You
can
4. The PR D / E button
Special
can
also be used to select the
preceding
or
following
page.
Teletext Functions
REVEAL
Press this button to
Press this button
display concealed information, such as solutions
again to remove the information from the display.
of riddles
or
puzzles.
SIZE
Selects double
height text.
enlarge the top half of the page.
button again to enlarge the bottom half of the
button again to return to the normal display.
Press this button to
Press this
Press this
page.
UPDATE
Displays
the TV
picture
the
on
Press this button to view the
while
screen
waiting
for the
new
teletext page.
teletext page.
updated
HOLD
Stops
the automatic page
change
which will
occur
if
a
teletext page consists of 2
or more
sub pages.
The number of sub pages and the sub page
time.
When this button is
and
the
pressed
change is
the automatic page
To continue press this button
displayed is, usually, shown on the screen below the
stop symbol is displayed at the top left-hand corner of the screen
inhibited.
again.
MIX
Displays
the teletext pages
To switch the TV
picture
superimposed
the TV
on
off press this button
picture.
again.
TIME
This button has two functions:
a)
When
the
b)
viewing
screen.
a
TV programme, press this button to
Press this button
In teletext
mode, press this button
at the bottom of the
screen.
buttons. Press this button
38
PLASMA TV
again
to
To hold
again
remove
to select
or
change
the
a
display
display.
the time at the
top right hand
sub page number. The sub page number is
the sub page, press the RED/ GREEN
to exit this function.
or
corner
of
displayed
PR D / E
Miscellaneous
EPG
(Electronic
(Electronic Programme Guide)
Guide)
(In
(In Digital mode only)
only)
EPG
-
This
(Electronic Programme Guide) (In Digital
system has
an
Electronic
Programme
mode
Guide
only)
(EPG)
to
help
your
navigation through
all the
possible viewing
options.
-
-
-
The EPG
supplies information such as programme listings, start and end times for all available services. In addition,
detailed information about the programme is often available in the EPG (the availability and amount of these
programme details will vary, depending on the particular broadcaster).
This function
The EPG
can
be used
displays
only
when the EPG information is broadcast
the programme
description
for next 8
by broadcasting companies.
days.
Switch on/off EPG
1.
Press the GUIDE button to switch
2.
Press the GUIDE button
again
on
EPG.
to switch off EPG and return to TV
viewing.
Select
a programme
Press the D / E , F / G button to select desired programme, then press the OK button to
programme.
Pressing the PR D / E button
repeatedly
display
the selected
turns the pages.
Owner's Manual
39
Miscellaneous
EPG
(Electronic
(Electronic Programme Guide)
Guide)
(In
(In Digital mode only)
only)
Button Function in NOW/NEXT Guide Mode
Remote Control Buttons
Function
RED
Shows the favourite programmes
GREEN
The detail information
YELLOW
Mode
F / G
Select NOW
on or
or
NEXT mode
Select the
PR D / E
GUIDE/EXIT
Switch off EPG
/ E
Button Function in 8
Days
Guide Mode
Remote Control Buttons
Function
RED
Shows the favourite programmes
GREEN
The detail information
YELLOW
Mode
change
BLUE
Show
or
Change
F / G
D
/ E
on or
or
all programmes
off
to Channel Guide
hide the 8
days
OSD
(On
Screen
to the selected channel
Select the programme for other time
Select the other programme for
PR D / E
Page Up/Down
GUIDE/EXIT
Switch off EPG
PLASMA TV
all programmes
change to 8 days Guide
Change to the selected channel
Broadcasting Programme
Page Up/Down
D
40
or
off
same
time
Display)
Miscellaneous
Button Function in Channel Guide Mode
Remote Control Buttons
Function
RED
Shows the favourite programmes
GREEN
The detail information
YELLOW
Mode
change
BLUE
Show
or
Change
on or
or
all programmes
off
to NOW/NEXT Guide
hide the 8
days
OSD
(On
Screen
F / G
Select
a
station
/ E
Select
a
programme time
PR D / E
broadcasting
broadcasting
Page Up/Down
GUIDE/EXIT
Switch off EPG
D
Button Function in Date
Change
Display)
to the selected channel
Mode
Remote Control Buttons
Function
BLUE
Show
F / G
Change
Change
E
Hide the 8
GUIDE/EXIT
Switch off EPG
or
hide the 8
days
to the selected channel
a
date
days
OSD
(On
Screen
Display)
Owner's Manual
41
Miscellaneous
External Control
Control Device Setup
Setup
Connect the RS-232C
-
input jack to an external
externally.
control device
(such
as a
computer
or an
A/V control
system)
and control the set's functions
How to connect external control
?
Connect the serial
?
RS-232C connection cables
?
The set remote control and front
computer
<
Back
panel
Type
or
of the set
to the RS-232C jack on the
supplied with the set.
panel controls (except main power) will
Monitor back
panel.
not
not be functional if the Monitor is controlled
>
No.
Pin
1
No connection
9-pin
male
1
name
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
5
(Receive data)
(Transmit data)
(DTE side ready)
9
(DCE side ready)
(Ready to send)
(Clear to send)
7
RTS
8
CTS
9
No Connection
6
configurations
7-wire
(Standard
3-wire
configuration
(Not standard)
configuration
RS-232C cable)
PC
PDP
PC
PDP
TXD
RXD
2
3
TXD
RXD
2
3
TXD
3
2
RXD
TXD
3
2
RXD
GND
5
5
GND
GND
5
5
GND
DTR
4
6
DSR
DTR
4
4
DTR
DSR
6
4
DTR
DSR
6
6
DSR
RTS
7
8
CTS
RTS
7
7
RTS
CTS
8
7
RTS
CTS
8
8
CTS
D-Sub 9
42
are
other external device.
of connector; D-Sub
RS-232C
equipment
port of the control device
PLASMA TV
D-Sub 9
D-Sub 9
D-Sub 9
by
a
PC
Miscellaneous
Set ID
-
-
Use this function to
specify a set ID number.
Mapping 1'. See page 48.
Refer to 'Real Data
1. Press the MENU button and then
use
the D/E button to select the SPECIAL
menu.
STATION
Language
Child lock
2. Press the G button and then
3. Press the G button and then
use
use
D/E
button to select Set ID.
F / G button to
adjust
PICTURE
ISM Method
SOUND
Set ID
Low power
Set ID to choose the desired
1
G
Demo
TIME
monitor ID number.
SPECIAL
?
4.
The
adjustment
range of Set ID is 1
99.
~
SCREEN
press the MENU button to return to normal TV
Repeatedly
viewing.
PIP/DW
MENU Prev.
Communication Parameters
?
Baud rate
?
Data
?
*
:
9600
bps (UART)
length : 8
Parity : None
bits
Use
(reverse)
a
crossed
?Stopbit:1bit
?
Communication code
:
ASCII code
cable.
Command Reference List
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
k
a
0~1
Input Select
Aspect Ratio
k
b
k
c
Refertop.44
Refertop.44
04. Screen Mute
k
d
0~1
05. Volume Mute
k
e
0~1
06. Volume Control
k
f
0~64
07. Contrast
k
g
0~64
08.
k
h
0~64
02.
03.
Brightness
Transmission /
Protocol
Receiving
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
*
[Command 1]
First command to control the set.
:
(j,k,morx)
*
*
[Command 2]
[Set ID]
:
Second command to control the set.
:
You
can
adjust
the set ID to choose
desired monitor ID number in
99.
Adjustment range is 1
When selecting Set ID '0', every
~
09. Colour
k
i
0~64
10. Tint
k
j
0~64
Set ID is indicated
11.
k
k
0~64
menu
12. OSD Select
k
l
0~1
13. Remote control lock mode
k
m
0~1
14. PIP/DW
k
n
0~3
15. PIP Position
k
q
0~3
16. Treble
k
r
0~64
17. Bass
k
s
0~64
18. Balance
k
t
0~64
19. Colour
k
u
0~3
k
v
0~50
k
w
0~50
Sharpness
connected PDP set is controlled.
on
*
20. Red
Temperature (CSM)
Adjustment
21. Green
Adjustment
Blue Adjustment
k
$
Source
k
y
Refertop.46
24. Abnormal Status
k
z
0~a
j
p
j
q
r
j
s
j
jt
u
j
0~3
22.
23. PIP
input
25. ISM Method
26. Low Power
27. Orbiter Time
Setting
Setting
Picture Size Setting for DW Mode
Auto Configure
28. Orbiter Pixel
29.
30.
31. Tune Command
m
a
32. Send IR Code
m
c
x
b
33.
34.
*
Input
Input
When
select
select
(Main)
(PIP)
setting
the 24
x
34,
~
a menu
y
doesn't
special
menu.
0~50
1~3
0~20
1
Refertop.47
Key Code
Refertop.48
Refertop.48
display
as
as
Hexa decimal
To transmit command data.
:
Transmit 'FF' data to read status of
command.
*
[Cr]
Carriage
:
Return
ASCII code '0x0D'
*
[]
ASCII code
:
'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
*
The set transmits ACK
(acknowledgement)
based
format when
normal data. At this
time, if the data
is data read
receiving
on
this
mode, it indicates present status data. If the
mode, it returns the data of the PC com-
data is data write
puter.
0~1
1~FE
[DATA]
decimal
(1~99)on
(0x0~0x63)
transmission/receiving protocol.
and
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
*
The set transmits ACK
(acknowledgement)
format when
abnormal data from
receiving
non-viable functions
Data
1:
Illegal
2: not
or
communication
based
on
this
errors.
Code
support function
3: Wait
more
time
on screen.
Owner's Manual
43
Miscellaneous
01. Power
04. Screen Mute
(Command
G To control Power On/Off of the Monitor.
2
G To select
mute on/off.
Transmission
Transmission
(Command
:
a)
0
Power Off
:
2
d)
:
[k][d][ ][Set ID][ ][Data][Cr]
[k][a][ ][Set ID][ ][Data][Cr]
Data
screen
Data
1:PowerOn
0
:
Screen mute off
1
:
Screen mute
(Picture on)
(Picture off)
on
Ack
Ack
[a][ ][Set ID][ ][OK][Data][x]
[d][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
05. Volume Mute
(Command
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume
mute on/off.
Ack
You
mute
the MUTE button
using
on
Transmission
In like manner, if other functions transmit '0xFF' data
based on this format, Acknowledgement data feed back
[k][e][ ][Set ID][ ][Data][Cr]
Data
status about each function.
presents
adjust
e)
:
remote control.
[a][ ][Set ID][ ][OK][Data][x]
*
also
can
2
0
:
Volume mute off
1
:
Volume mute
(Volume on)
(Volume off)
on
Ack
02.
Select
Input
G To select input
You
source
also select
can
button
(Command
an
2
b)
:
[e][ ][Set ID][ ][OK][Data][x]
for the set.
input
source
using
the INPUT
06. Volume Control
the set's remote control.
on
You
[k][b][ ][Set ID][ ][Data][Cr]
on
can
also
adjust
f)
volume with the volume buttons
5
:
Component2
1
:
Analogue
6
:
RGB-DTV
2
:
Video1
7
:
RGB-PC
[k][f][ ][Set ID][ ][Data][Cr]
3
:
Video2
8
:
DVI-DTV
Data
4
:
Component1
9
:
DVI-PC
Transmission
Min:0~Max:64
*
Refer to 'Real data
mapping
1'. See page 48.
Ack
[b][ ][Set ID][ ][OK][Data][x]
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast
03.
Ratio
Aspect
(Command
2
:
c) (Main
Picture
Size)
G To adjust
You
G To adjust the
You
can
(Aspect
screen
also
Ratio
SCREEN
format.
(Main picture format)
screen format using the ARC
adjust the
Control) button
on
remote control
or
in the
menu.
1
:
2
:
3
:
(4:3)
Wide screen (16:9)
Horizon (Spectacle)
screen
:
Original
mapping
1'. See page 48.
8:Full
08.
Brightness (Command
you select either 16:9
You
or
4:3
screen
can
2
brightness.
adjust brightness
:
h)
screen
also
in the PICTURE
menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Refer to 'Real data
mapping
Ack
[h][ ][Set ID][ ][OK][Data][x]
PLASMA TV
menu.
[g][ ][Set ID][ ][OK][Data][x]
[c][ ][Set ID][ ][OK][Data][x]
input,
contrast in the PICTURE
Refer to 'Real data
G To adjust
the PC
adjust
7:14:9
Ack
aspect ratio.
g)
Ack
6
4:Zoom
Using
:
Min:0~Max:64
*
Normal
also
2
contrast.
[k][g][ ][Set ID][ ][Data][Cr]
Data
[k][c][ ][Set ID][ ][Data][Cr]
Data
can
(Command
screen
Transmission
Transmission
44
:
remote control.
0:DTV
Ack
*
2
G To adjust volume.
Transmission
Data
(Command
1'. See page 48.
Miscellaneous
09. Colour
(Command
G To adjust the
You
can
also
screen
adjust
2
i)
:
14.PIP/DW(Command2:n)
G To control the PIP (Picture In picture)/DW.
colour.
colour in the PICTURE
You
menu.
on
Transmission
the PIP/DW button
menu.
[k][n][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
using
in the PIP/DW
or
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
also control the PIP/DW
can
the remote control
Refer to 'Real data
mapping
1'. See page 48.
Data 0: PIP/DW off
Ack
1: PIP
[i][ ][Set ID][ ][OK][Data][x]
2: DW1
3: DW2
10. Tint
(Command
G To adjust the
You
can
also
screen
adjust
2
:
Ack
j) (option)
[n][ ][Set ID][ ][OK][Data][x]
tint.
tint in the PICTURE
menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
15. PIP Position
Red:0~Green:64
*
Refer to 'Real data
mapping
1'. See page 48.
the sub
picture position using
remote control
[j][ ][Set ID][ ][OK][Data][x]
You
can
also
2
sharpness.
adjust sharpness in
Data
screen
the PICTURE
menu.
Min:0~Max:64
Refer to 'Real data
in the PIP/DW
or
can
POSITION button
also
on
adjust
the
menu.
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
Ack
[k][k][ ][Set ID][ ][Data][Cr]
*
q)
[k][q][ ][Set ID][ ][Data][Cr]
k)
:
Transmission
Data
:
Transmission
Sharpness (Command
G To adjust the
2
G To select sub picture position for PIP. You
Ack
11.
(Command
[q][ ][Set ID][ ][OK][Data][x]
mapping
1'. See page 48.
Ack
[k][ ][Set ID][ ][OK][Data][x]
16. Treble
12. OSD Select
(Command
2
:
2
(Command
:r)
G To adjust treble.
l)
You
G To select OSD (On Screen Display) on/off when
can
also
adjust
treble in the SOUND
menu.
con-
Transmission
trolling remotely.
[k][r][ ][Set ID][ ][Data][Cr]
Transmission
Data
[k][l][ ][Set ID][ ][Data][Cr]
Data0
:OSDoff
Min:0~Max:64
*
1:OSDon
Refer to 'Real data
mapping
1'. See page 48.
Ack
Ack
[r][ ][Set ID][ ][OK][Data][x]
[l][ ][Set ID][ ][OK][Data][x]
13. Remote control lock mode
G To lock the front panel controls
(Command
on
2
:
m)
the monitor and remote
control.
You
[k][m][ ][Set ID][ ][Data][Cr]
:
Lock off
1:Lockon
you're
not
:
s)
using
the remote
When main power is
released.
can
also
adjust
bass in the SOUND
menu.
[k][s][ ][Set ID][ ][Data][Cr]
Data
control, use this mode.
on/off, external control lock is
Min:0~Max:64
*
[m][ ][Set ID][ ][OK][Data][x]
If
2
Transmission
Ack
*
(Command
G To adjust bass.
Transmission
Data 0
17. Bass
Refer to 'Real data
mapping
1'. See page 48.
Ack
[s][ ][Set ID][ ][OK][Data][x]
Owner's Manual
45
Miscellaneous
18. Balance
(Command
2
:
23. PIP
t)
G To adjust balance.
You
can
also
adjust
G To select input
balance in the SOUND
mode. You
menu.
using
Transmission
Refer to 'Real data
2
y)
:
for sub picture in
adjust input source
PIP/Twin
source
also
can
PIP INPUT button
on
picture
picture
for sub
remote control.
[k][y][ ][Set ID][ ][Data][Cr]
Min:0~Max:64
*
(Command
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
Select
Input
mapping
1'. See page 48.
Data
Ack
[t][ ][Set ID][ ][OK][Data][x]
0:DTV
5
:
Component2
1
:
Analogue
6
:
RGB-DTV
2
:
Video1
7
:
RGB-PC
3
:
Video2
8
:
DVI-DTV
4
:
Component1
9
:
DVI-PC
Ack
19. Colour
Temperature (Command
2
:
u)
[y][ ][Set ID][ ][OK][Data][x]
G To adjust colour temperature.
You
can
also
adjust
CSM in the PICTURE
menu.
Transmission
24. Abnormal State
[k][u][ ][Set ID][ ][Data][Cr]
G To recognize
Data
0: Normal
1: Cool
2: Warm
3: User
Ack
(Command
2
:
z)
abnormal state.
an
Transmission
[k][z][ ][Set ID][ ][FF][ ][Cr]
[u][ ][Set ID][ ][OK][Data][x]
Data
FF
:
Read
Ack
[z][ ][Set ID][ ][OK][Data][x]
20. Red
Adjustment (Command
2
v)
:
Data
0: Normal
2:
Transmission
3:
[k][v][ ][Set ID][ ][Data][Cr]
4:
Data
5: 5V down
Min:0~Max:50
*
Refer to 'Real data
(Power on and signal exist)
signal (Power on)
Turn the monitor off by remote control
Turn the monitor off by sleep time function
Turn the monitor off by RS-232C function
1: No
G To adjust red in colour temperature.
mapping
6: AC down
2'. See page 48.
7: Turn the monitor off
Ack
8: Turn the monitor off
[v][ ][Set ID][ ][OK][Data][x]
9: Turn the monitor off
a:
*
21. Green
Adjustment (Command
2
:
Turn the monitor off
This function is "read
by
by
by
by
Fan Alarm function
Off time function
Auto
sleep
function
AV board detect
only".
w)
G To adjust green in colour temperature.
25. ISM Method
Transmission
(Command
1
:
j,
Command 2
:
p)
[k][w][ ][Set ID][ ][Data][Cr]
Data
G To control the ISM method. You
Min:0~Max:50
*
Refer to 'Real data
mapping
Method in SPECIAL
2'. See page 48.
can
also
ISM
adjust
menu.
Transmission
Ack
[j][p][ ][Set ID][ ][Data][Cr]
[w][ ][Set ID][ ][OK][Data][x]
MSB
LSB
00000000
22. Blue
Adjustment (Command
2
:
$)
Reserved
Inversion
G To adjust blue in colour temperature.
Orbiter
Transmission
White wash
[k][$][ ][Set ID][ ][Data][Cr]
Data
Normal
Min:0~Max:50
*
Refer to 'Real data
mapping
2'. See page 48.
*
This describes the limitation of
that two functions
Ack
[$][ ][Set ID][ ][OK][Data][x]
PLASMA TV
command. "x" express
not
express that two
If the data does not meet this
acknowledgement.
46
a
displayed simultaneously. "o"
functions are displayed simultaneously.
are
limitation, it sends NG
Miscellaneous
7
6
5
4
3
2
1
0
Function
0
Inversion Off
1
Inversion ON
0
Orbiter Off
1
Orbiter On
0
White wash Off
1
White wash On
Normal Off
0
Normal On
1
29. Picture Size
G To select the PIP picture format.
You
x
x
format
picture
using
the
the remote control.
on
Transmission
[j][t][ ][Set ID][ ][Data][Cr]
Data
Min: 0
Max: 20
~
Refer to 'Real data
Reserved
x
also select the PIP
can
SIZE
*
x
Setting for DW Mode
: j, Command 2 : t)
1
(Command
mapping
1'.
Ack
*
Limitation
Normal
White wash
Orbiter
Inversion
Normal
o
x
x
x
White wash
x
o
o
x
Orbiter
x
o
o
o
Inversion
x
x
o
o
[t][ ][Set ID][ ][OK/NG][Data][x]
30. Auto
Configure
(Command 1 : j,
Command 2
:
u)
G To adjust picture position and minimize image shaking
It works
automatically.
Ack
only
in RGB
(PC)
mode.
Transmission
[p][ ][Set ID][ ][OK/NG][Data][x]
[j][u][ ][Set ID][ ][Data][Cr]
Data
26. Low Power
(Command
1
:
j,
Command 2
:
q)
G To reduce the power consumption of the
also
adjust
1: To set
Ack
Low Power in SPECIAL
[u][ ][Set ID][ ][OK/NG][Data][x]
set. You
can
menu.
Transmission
31. Tune Command
(Command
[j][q][ ][Set ID][ ][Data][ ][Cr]
Data 0
:Off
G Tune channel
1
:On
Transmission
Ack
1
Setting
: j, Command
G To adjust orbiter operation time
:
High
:
Low channel data
*
2
:
r)
Data2
term.
Digital
1'.
00 2F
->
->
a)
:
ATV Main
0x01
:
ATV Sub
0x10
:
DTV Main
0x11
:
DTV Sub
-
Min: 00
(2FH)
(188H)
01 88
0x00
-
Max: FE
mapping
No. 47
Channel data range
Analogue Min: 00
~
Refer to 'Real data
:
number.
channel data
No. 394
[j][r][ ][Set ID][ ][Data][ ][Cr]
Min: 1
following physical
Data1
Transmission
Data
m, Command 2
Data0
ex.
(Command
:
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
[q][ ][Set ID][ ][OK/NG][Data][x]
27. Orbiter Time
1
to
~
Max: 63
Max: 3E7
~
(0~99)
(0~999)
Ack
Ack
[a][ ][Set ID][ ][OK/NG][Data][x]
[r][ ][Set ID][ ][OK/NG][Data][x]
28. Orbiter Pixel
(Command
1
Setting
: j, Command
Data
2
:
s)
Min: 00
32. Send IR Code
(Command
G To adjust pixel number in orbiter function.
Transmission
G To send IR
[j][s][ ][Set ID][ ][Data][Cr]
Transmission
Data
Refer to 'Real data
1
:
remote
m, Command 2
key
:
c)
code.
[m][c][ ][Set ID][ ][Data][Cr]
Min:1~Max:3
*
Max: FF
~
mapping
1'.
Data
Key
code
-
Refer to page 50.
Ack
[s][ ][Set ID][ ][OK/NG][Data][x]
Ack
[c][ ][Set ID][ ][OK/NG][Data][x]
Owner's Manual
47
Miscellaneous
33.
Input select (Command
(Main Picture Input)
G To select input
source
1
:
x, Command 2
b)
34.
Input
select
G To adjust input
for main
picture.
(Command
source
for sub
1
:
x, Command 2
picture
y)
in PIP mode.
[x][y][ ][Set ID][ ][Data][Cr]
[x][b][ ][Set ID][ ][Data][Cr]
Data
Structure
Structure
MSB
MSB
0
:
Transmission
Transmission
Data
:
LSB
LSB
0
0000000
0000000
External
Input
External
Input
Input
External
Input
External
Input
Data
0000
DTV
0001
Analogue
0010
AV
0011
S-Video
0100
Component
0101
RGB-DTV
0110
RGB-PC
1001
HDMI
Data
0000
DTV
0001
Analogue
0010
AV
0011
S-Video
0100
Component
0101
RGB-DTV
0110
RGB-PC
1001
HDMI
Input
Number
Data
Data
0000
Input1
0000
Input1
0001
Input2
0001
Input2
0010
Input3
0010
Input3
0011
Input4
0011
Input4
0100
Input5
0100
Input5
0101
Input6
0101
Input6
Input
Number
Number
Input
Number
Ack
[y][ ][Set ID][ ][OK/NG][Data][x]
Ack
[b][ ][Set ID][ ][OK/NG][Data][x]
*
Real data
mapping
1
*
Real data
0
:Step0
0:-40
A
:Step10(SetID10)
2:-38
1:-39
48
PLASMA TV
F :Step15(SetID15)
10:Step16(SetID16)
28:0
64
:
Step
100
4E:+38
6E
:
Step
110
73
74
:
Step
Step
115
116
C7
:
Step
199
FE
FF
:
Step
Step
254
:
:
255
4F:+39
50:+40
mapping
2
Miscellaneous
IR Code
Code
(NEC
(NEC Format)
How to connect
G
Connect your wired remote control to the Remote Control
Remote Control IR Code
port
on
the Monitor.
(NEC Format)
G Output waveform
Single pulse,
modulated with 37.917KHz
at 455KHz
signal
TC
Carrier
frequency
FCAR
1/TC
Duty
T1
=
ratio
=
=
fOSC/12
T1/TC
1/3
=
G Configuration of frame
?
1st frame
Lead
Low
High
code
custom code
custom code
Data code
Data code
C0 C1C2C3C4C5C6C7C0C1C2C3C4C5C6C7D0D1D2D3D4D5D6D7D0D1D2D3D4D5D6D7
?
Repeat
frame
Repeat
code
Tf
G Lead code
9ms
4.5
ms
0.55
G Repeat code
ms
9ms
2.25
ms
G Bit description
?
?
Bit "0"
0.56
0.56
ms
1.12
G Frame interval
:
Bit "1"
ms
2.24
ms
ms
Tf
The waveform is transmitted
Tf
as
long
as a
key
is
depressed.
Tf
Tf=108ms @455KHz
Owner's Manual
49
Miscellaneous
Code
Note
PR D
R/C Button
01
PR E
R/C Button
02
VOL D
R/C Button
03
VOL E
R/C Button
40
Up( D )
R/C Button
41
Down
R/C Button
00
06
07
( E)
Right (G)
Left (F)
R/C Button
R/C Button
POWER
R/C Button
POWER ON
Discrete IR Code
C5
POWER OFF
Discrete IR
09
MUTE
R/C Button
10
Number
11
Number
12
Number
13
Number
14
Number
15
Number
16
Number
17
Number
18
Number
19
Number
0B
INPUT
R/C Button
BF
COMPONENT
Discrete IR Code
C6
HDMI
Discrete IR Code
D5
RGB
Discrete IR Code
D6
TV
Discrete IR Code
5A
AV1
Discrete IR Code
D0
AV2
Discrete IR Code
D1
AV3
Discrete IR Code
D2
AV4
Discrete IR Code
D3
SAV2
Discrete IR Code
AB
GUIDE
R/C Button
39
SUBTITLE/ *
R/C Button
5B
EXIT
R/C Button
1E
FAV
R/C Button
1A
Q.VIEW
R/C Button
50
D/A TV
R/C Button
0A
I/II
R/C Button
0E
SLEEP
R/C Button
43
MENU
R/C Button
44
OK(
4D
PSM
R/C Button
52
SSM
R/C Button
53
LIST
R/C Button
20
TEXT
R/C Button
2A
REVEAL
R/C Button
24
MIX
R/C Button
26
TIME
R/C Button
62
UPDATE / POSITION
R/C Button
64
SIZE
R/C Button
65
HOLD
R/C Button
70
INDEX
R/C Button
60
PIP
R/C Button
C3
PIP INPUT
R/C Button
C2
SWAP
R/C Button
C0
PIP PR+
R/C Button
C1
PIP PR-
R/C Button
61
BLUE
R/C Button
72
Key
YELLOW Key
GREEN Key
RED Key
79
ARC
R/C Button
76
ARC
77
ARC
AF
ARC
08
C4
63
71
50
Function
(Hexa)
PLASMA TV
Key
Key
Key
Key
Key
Key
Key
Key
Key
Key
0
R/C Button
1
R/C Button
2
R/C Button
3
R/C Button
4
R/C Button
5
R/C Button
6
R/C Button
7
R/C Button
8
R/C Button
9
R/C Button
)
(4:3)
(16:9)
(Zoom)
(Power On/Off)
(Only Power On)
Code (Only Power Off)
COMPONENT
(Input
(Input
(Input
(Input
(Input
(Input
(Input
(Input
(Input
Selection)
Selection)
RGB Selection)
TV Selection)
AV1 Selection)
AV2 Selection)
AV3 Selection)
AV4 Selection)
SAV2 Selection)
(Only
(Only
(Only
4:3
HDMI
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code
Discrete IR Code
Discrete IR Code
mode)
mode)
Zoom mode)
16:9
Miscellaneous
the Remote
Programming
G The
remote is
a
multi-brand
or a
universal remote. It
can
be
programmed
to
operate
most remote-controllable devices of
turn
the device such
other manufacturers.
Note that the remote may not control all models of other brands.
Programming
a
code
code into
a
1. To find out whether your remote
remote mode
can
operate the device without programming,
press the corresponding mode button on the remote.
After that, press the POWER button. If the device is turned off then it
be
programmed.
explained below.
If not, the remote should be
2. Press the MENU and MUTE button
programmed
continuously
at the
to
same
on
responds properly
as a
VCR and
and the remote need not to
operate the device. The programming procedures
time for 2
seconds, the
are
current selected device button
will be illuminated.
If you don't press any button for 20
repeat from step 2.
3. Enter code numbers
pressing
the
using
seconds, the light
the number button
button, the light blinks
at
a
time.
on
see
if the device
the mode button will be turned off. In that case, you have to
the remote
by referring
If the device turned
4. Press the MENU button to store the code. After
5. Test the remote functions to
on
blinking twice,
the code table
on
the
following
pages. When
off, the programming is successful.
this code is stored.
responds properly.
If not,
repeat from step
2.
Owner's Manual
51
Miscellaneous
VCRs
VCRs
Codes
Brand
Codes
AIWA
Brand
034
KENWOOD
014
034
AKAI
016
043
047
048
125
146
001
012
013
101
106
114
046
124
LG
AMPRO
072
ANAM
031
033
103
AUDIO DYNAMICS
012
023
039
BROKSONIC
035
037
129
CANON
028
031
033
043
(GOLDSTAR)
039
Brand
Codes
PORTLAND
108
TATUNG
039
043
PULSAR
072
TEAC
034
039
043
020
QUARTZ
011
014
TECHNICS
031
033
070
123
QUASAR
033
066
075
145
TEKNIKA
019
031
033
034
RCA
013
020
033
034
043
Brand
Codes
LLOYD
034
LXI
003
009
013
014
040
041
062
063
THOMAS
034
017
034
101
106
107
109
140
144
TMK
006
145
147
TOSHIBA
008
003
008
010
014
031
033
034
040
053
054
101
MAGIN
040
MAGNAVOX
031
033
067
068
012
031
013
042
047
059
082
112
131
TOTEVISION
040
101
UNITECH
040
058
VECTOR RESEARCH
012
148
VICTOR
048
VIDEO CONCEPTS
012
VIDEOSONIC
040
CAPEHART
108
CRAIG
003
040
135
CURTIS MATHES
031
033
041
DAEWOO
005
007
010
064
069
RICO
065
108
110
111
MARTA
101
RUNCO
112
116
117
119
MATSUI
027
030
SALORA
014
034
046
MEI
031
033
SAMSUNG
032
040
102
104
MEMOREX
003
010
014
031
105
107
109
112
WARDS
003
013
017
024
033
034
053
072
113
115
120
122
031
033
034
040
101
102
134
139
125
053
054
131
059
MARANTZ
034
033
041
067
DAYTRON
108
DBX
012
023
DYNATECH
034
053
ELECTROHOME
059
EMERSON
006
017
025
027
MGA
045
046
029
031
034
035
MINOLTA
013
020
036
037
046
101
MITSUBISHI
013
020
045
046
129
131
138
153
049
051
059
061
FISHER
003
008
009
010
FUNAI
034
MTC
034
040
GE
031
033
063
072
MULTITECH
024
034
107
109
144
147
NEC
012
023
GO VIDEO
132
136
HARMAN KARDON
012
045
NORDMENDE
043
HITACHI
004
018
026
034
OPTONICA
053
054
043
063
137
150
PANASONIC
066
070
074
INSTANTREPLAY
031
033
133
140
145
JCL
031
033
013
020
031
JCPENNY
012
013
015
040
066
101
039
043
REALISTIC
101
SANSUI
022
043
048
135
YAMAHA
012
034
039
SANYO
003
007
010
014
ZENITH
034
048
056
102
134
058
072
080
SCOTT
017
037
112
129
SEARS
003
008
009
010
013
014
017
020
031
042
073
081
151
131
039
043
048
PENTAX
033
JENSEN
043
JVC
012
031
033
043
048
050
055
060
130
150
152
101
083
031
034
067
PHILIPS
031
033
034
067
071
101
021
048
PILOT
101
PIONEER
013
031
054
149
SHINTOM
024
SONY
003
009
031
052
056
057
058
076
077
078
149
033
034
033
063
PHILCO
SHARP
054
SOUNDESIGN
034
STS
013
SYLVANIA
031
059
067
SYMPHONIC
034
TANDY
010
034
DVD
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
Brand
022
MAGNAVOX
013
PHILIPS
013
SONY
007
DENON
020
014
MARANTZ
024
PIONEER
004
THOMPSON
005
006
GE
005
006
MITSUBISHI
002
PROCEED
021
TOSHIBA
019
008
026
HARMAN KARDON 027
NAD
023
PROSCAN
005
006
YAMAHA
009
018
JVC
012
ONKYO
008
017
RCA
005
006
ZENITH
010
016
LG
001
PANASONIC
003
009
SAMSUNG
011
015
52
PLASMA TV
010
016
025
025
043
101
Miscellaneous
Notes
Owner's Manual
53
Miscellaneous
T roubleshooting Checklist
Checklist
No
picture
&
?
Check whether the set is turned
?
Power cord inserted into wall outlet?
on.
No sound
?
another
was
?
Sound muted? Press MUTE button.
Check to
causing
?
The remote control
see
to
p.6)
new
No
are
installed with the correct
as
the
(Refer
to
image
is muted
p.6)
Select Colour in the PICTURE
to
during the startup process of
picture has not appeared
the set.
menu
and press the VOLUME
button.
certain distance between the set and the VCR.
Keep
?
Activate any function to restore the
a
still
picture
is
on
the
screen
for
?
Check for local interference such
?
Adjust
?
A
brightness
more
as an
than 5
of the
of the
Unusual sound from
inside the set
PLASMA TV
Balance in the SOUND
change
in ambient
at the time of
the set.
menu.
electrical
(Refer
picture.
minutes, the
picture shaking
one
(G)
after five
p.24)
?
picture
output from
polarities.
Please contact your service centre, if the
minutes.
speakers
54
batteries.
This is normal
(If
or
if the batteries
Install
(Refer
Horizontal/vertical bars
between the set and the remote control
object
Check if the remote control handset is set up to correct mode.
?
Poor colour
if there is any
see
?
?
Poor
button.
?
Picture appears slowly,
after switching on
or
(G)
obstruction.
Check to
(Refer
doesn't work
or
power cord into the wall outlet where the set's power
Press the VOLUME
?
No
product's
plugged in.
?
Picture OK &
No sound
Plug
cord
to
appliance
screen
or
gets dark.)
power tool.
p.25)
humidity or temperature may result in an unusual noise
switching off or on of the set and does not indicate a fault with
Miscellaneous
Product
Specifications
Specifications
42PX4DV-EA
MODEL
Width
(inches
/
mm)
49.3 / 1252
Height (inches
/
mm)
27.8 / 705
Depth (inches
/
mm)
11.3 / 285
Weight (pounds
Power
/
84.5 / 38.3
kg)
requirement
AC100-240V, 50/60Hz
32
Operating Temperature Range
The
specifications
shown above may be
104°F
(0
40°C)
~
Less than 80%
Operating Humidity Range
?
~
changed
without notice for
quality improvement.
Owner's Manual
55
Download PDF