LG | 47LB570V | LG 47LB570V Owner’s Manual

OWNER’S MANUAL
*
LED TV
* LG LED TVs are LCD TVs with LED backlighting.
Please read this manual carefully before operating your set and retain
it for future reference.
LB49** LB61**
LB57**
LB58**
*MFL68027048*
www.lg.com
P/NO : MFL68027048(1406-REV03)
Printed in Korea
2
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
ENGLISH
LICENSES
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com .
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
y yDo not place the TV and/or remote control in the following environments:
- -A location exposed to direct sunlight
- -An area with high humidity such as a bathroom
- -Near any heat source such as stoves and other devices that produce
heat
- -Near kitchen counters or humidifiers where they can easily be exposed
to steam or oil
- -An area exposed to rain or wind
- -Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product
deformation.
y yDo not place the product where it might be exposed to dust.
This may cause a fire hazard.
y yMains Plug is the TV connecting/disconnecting device to AC mains electric
supply.This plug must remain readily attached and operable when TV is in
use.
y yDo not touch the power plug with wet hands. Additionally, if the cord pin is
wet or covered with dust, dry the power plug completely or wipe dust off.
You may be electrocuted due to excess moisture.
y yMake sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on earth.)
Otherwise possibility you may be electrocuted or injured.
y yInsert power cable plug completely into wall socket otherwise if not secured
completely into socket, fire ignition may break out.
y yEnsure the power cord does not come into contact with hot objects such as
a heater.
This may cause a fire or an electric shock hazard.
y yDo not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
ENGLISH
SAFETY INSTRUCTIONS
3
4
SAFETY INSTRUCTIONS
ENGLISH
y yBend antenna cable between inside and outside building to prevent rain
from flowing in.
This may cause water damaged inside the Product and could give an
electric shock.
y yWhen mounting TV onto wall make sure to neatly install and isolate cabling
from rear of TV as to not create possibility of electric shock /fire hazard.
y yDo not plug too many electrical devices into a single multiple electrical
outlet.
Otherwise, this may result in fire due to over-heating.
y yDo not drop the product or let it fall over when connecting external devices.
Otherwise, this may result in injury or damage to the product.
Des
icca
nt
y yKeep the anti-moisture packing material or vinyl packing out of the reach of
children.
Anti-moisture material is harmful if swallowed. If swallowed by mistake,
force the patient to vomit and visit the nearest hospital. Additionally, vinyl
packing can cause suffocation. Keep it out of the reach of children.
y yDo not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
y yDispose of used batteries carefully to ensure that a small child does not
consume them.
Please seek Doctor- Medical Attention immediately if child consumes
batteries.
y yDo not insert any metal objects/conductors (like a metal chopstick/cutlery/
screwdriver) between power cable plug and input Wall Socket while it is
connected to the input terminal on the wall. Additionally, do not touch the
power cable right after plugging into the wall input terminal. You may be
electrocuted.
(Depending on model)
y yDo not put or store inflammable substances near the product.
There is a danger of combustion/explosion or fire due to careless handling
of the inflammable substances.
y yDo not drop metallic objects such as coins, hair pins, chopsticks or wire into
the product, or inflammable objects such as paper and matches. Children
must pay particular attention.
Electrical shock, fire or injury can occur. If a foreign object is dropped into
the product, unplug the power cord and contact the service centre.
y yDo not spray water on the product or scrub with an inflammable substance
(thinner or benzene). Fire or electric shock accident can occur.
SAFETY INSTRUCTIONS
y yNever touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
y yNever touch the wall outlet when there is leakage of gas, open the windows
and ventilate.
It may cause a fire or a burn by a spark.
y yDo not disassemble, repair or modify the product at your own discretion.
Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
y yIf any of the following occur, unplug the product immediately and contact
your local service centre.
- -The product has been impacted by shock
- -The product has been damaged
- -Foreign objects have entered the product
- -The product produced smoke or a strange smell
This may result in fire or electric shock.
y yUnplug the TV from AC mains wall socket if you do not intend to use the TV
for a long period of time.
Accumulated dust can cause fire hazard and insulation deterioration can
cause electric leakage/shock/fire.
y yApparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
y yDo not install this product on a wall if it could be exposed to oil or oil mist.
This may damage the product and cause it to fall.
CAUTION
y yInstall the product where no radio wave occurs.
y yThere should be enough distance between an outside antenna and power
lines to keep the former from touching the latter even when the antenna
falls.
This may cause an electric shock.
ENGLISH
y yDo not allow any impact, shock or any objects to fall into the unit, and do
not drop anything onto the screen.
You may be injured or the product can be damaged.
5
6
SAFETY INSTRUCTIONS
ENGLISH
y yDo not install the product on places such as unstable shelves or inclined
surfaces. Also avoid places where there is vibration or where the product
cannot be fully supported.
Otherwise, the product may fall or flip over, which may cause injury or
damage to the product.
y yIf you install the TV on a stand, you need to take actions to prevent the
product from overturning. Otherwise, the product may fall over, which may
cause injury.
y yIf you intend to mount the product to a wall, attach VESA standard mounting interface (optional
parts) to the back of the product. When you install the set to use the wall mounting bracket (optional
parts), fix it carefully so as not to drop.
y yOnly use the attachments / accessories specified by the manufacturer.
y yWhen installing the antenna, consult with a qualified service technician. If
not installed by a qualified technician, this may create a fire hazard or an
electric shock hazard.
y yWe recommend that you maintain a distance of at least 2 to 7 times the
diagonal screen size when watching TV.
If you watch TV for a long period of time, this may cause blurred vision.
y yOnly use the specified type of battery.
This could cause damage to the remote control.
y yDo not mix new batteries with old batteries.
This may cause the batteries to overheat and leak.
y yBatteries should not be exposed to excessive heat. For example, keep away from direct Sunlight ,
open fireplace and electric heaters .
y yDo not place non-rechargeable batteries in charging device.
y yMake sure there are no objects between the remote control and its sensor.
y ySignal from Remote Control can be interrupted due to external/internal
lighting eg Sunlight, fluorescent lighting.
If this occurs turn off lighting or darken viewing area.
y yWhen connecting external devices such as video game consoles, make
sure the connecting cables are long enough.
Otherwise, the product may fall over, which may cause injury or damage
the product.
y yDo not turn the product On/Off by plugging-in or unplugging the power plug
to the wall outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an electric shock.
SAFETY INSTRUCTIONS
y yTake care not to touch the ventilation openings when watching the TV for
long periods as the ventilation openings may become hot. This does not
affect the operation or performance of the product.
y yPeriodically examine the cord of your appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an
exact replacement part by an authorized servicer.
y yPrevent dust collecting on the power plug pins or outlet.
This may cause a fire hazard.
y yProtect the power cord from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked upon. Pay particular
attention to plugs, wall outlets, and the point where the cord exits the
appliance.
y yDo not press strongly upon the panel with a hand or sharp object such
as nail, pencil or pen, or make a scratch on it, as it may cause damage to
screen.
y yAvoid touching the screen or holding your finger(s) against it for long
periods of time. Doing so may produce some temporary or permanent
distortion/damage to screen.
y yWhen cleaning the product and its components, unplug the power first and
wipe it with a soft cloth. Applying excessive force may cause scratches or
discolouration. Do not spray with water or wipe with a wet cloth. Never use
glass cleaner, car or industrial shiner, abrasives or wax, benzene, alcohol
etc., which can damage the product and its panel.
Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).
y yAs long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
y yWhen unplugging the cable, grab the plug and unplug it, by pulling at the
plug.
Don’t pull at the cord to unplug the power cord from the power board, as
this could be hazardous.
y yWhen moving the product, make sure you turn the power off first. Then,
unplug the power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire hazard
or cause electric shock.
ENGLISH
y yPlease follow the installation instructions below to prevent the product from
overheating.
- -The distance between the product and the wall should be more than
10 cm.
- -Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
- -Do not install the product on a carpet or cushion.
- -Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
7
8
SAFETY INSTRUCTIONS
ENGLISH
y yWhen moving or unpacking the product, work in pairs because the product
is heavy.
Otherwise, this may result in injury.
y yContact the service centre once a year to clean the internal parts of the
product.
Accumulated dust can cause mechanical failure.
y yRefer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
y yIf the product feels cold to the touch, there may be a small “flicker” when it
is turned on. This is normal, there is nothing wrong with product.
y yThe panel is a high technology display product with resolution of two million
to six million pixels. You may see tiny black dots and/or brightly coloured
dots (red, blue or green) at a size of 1 ppm on the panel. This does not
indicate a malfunction and does not affect the performance and reliability of
the product.
This phenomenon also occurs in third-party products and is not subject to
exchange or refund.
y yYou may find different brightness and color of the panel depending on your
viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not
related with the product performance, and it is not malfunction.
y yDisplaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video
game) for a prolonged time may cause damage to the screen, resulting in retention of the image,
which is known as image sticking. The warranty does not cover the product for image sticking.
Avoid displaying a fixed image on your television’s screen for a prolonged period (2 or more hours
for LCD, 1 or more hours for Plasma).
Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders
of the panel.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
y yGenerated Sound
“Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by
plastic thermal contraction due to tempera-ture and humidity. This noise is common for products
where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise
is generated from a high-speed switching circuit, which supplies a large amount of current to
operate a product. It varies depending on the product.
This generated sound does not affect the performance and reliability of the product.
ASSEMBLING AND PREPARING
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
y y Do not use any unapproved items to ensure the safety and product life span.
y y Any damage or injuries caused by using unapproved items are not covered by the warranty.
y y Some models have a thin film attached on to the screen and this must not be removed.
NOTE
y y The items supplied with your product may vary depending on the model.
y y Product specifications or contents of this manual may be changed without prior notice due to
upgrade of product functions.
y y For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm
thick and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
ENGLISH
NOTE
y y Image shown may differ from your TV.
y y Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
y y The available menus and options may differ from the input source or product model that you are
using.
y y New features may be added to this TV in the future.
y y The TV can be placed in standby mode in order to reduce the power consumption. And the TV
should be turned off if it will not be watched for some time, as this will reduce energy consumption.
y y The energy consumed during use can be significantly reduced if the level of brightness of the
picture is reduced, and this will reduce the overall running cost.
9
10
ASSEMBLING AND PREPARING
ENGLISH
ENERGY AV MODE INPUT
TV
SAVING
1
2
4
5
7
8
9
0
FLASHBK
LIST
3
6
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Remote Control, Batteries
(AAA)
Owner’s Manual
Cable Holder
Cable Managements
2EA
(Only LB57**, LB58**-ZA/ZB/
ZG/ZJ, LB61**)
Stand Base
(Only LB49**-ZH)
Stand Base
(Only LB49**-ZB/ZG)
Stand Base
(Only LB57**, LB58**-ZA/ZB/
ZG/ZJ, LB61**)
Stand Base/Stand Body
(Only LB58**-ZM/ZW)
Power Cord
(Only LB57**, LB58**,
LB61**)
ASSEMBLING AND PREPARING
11
ENGLISH
AC-DC Adapter / Power
Cord
(Only LB49**)
Stand Screws
2 EA, M4 x L10
(Only 28LB49**-ZH)
Stand Screws
4EA, M4 x L14
(Only 39/42/47/50LB57**,
39/42/47/50/55LB58**ZA/ZB/ZG/ZJ,
42/47/50/55/60LB58**-ZM/
ZW, LB61**)
Stand Screws
2EA, M4 x L20
(Only 32/39LB58**-ZM)
4EA, M4 x L20
(Only 32LB57**,
32LB58**-ZA/ZB/ZG/ZJ)
Stand Screws
4EA, M4 x L20
(Only LB58**-ZM/ZW)
Wall Mount Spacers
2EA
(Only 42LB57**, 42LB58**)
Rubbers
2EA
(Only LB58**-ZM/ZW)
Wi-Fi/Bluetooth Dongle
(Dongle / Cable / Velcro / Owner’s Manual)
(Only LB585*)
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
7
8
9
0
FLASHBK
LIST
6
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Magic Remote, Batteries
(AA)
(Only LB585*)
12
ASSEMBLING AND PREPARING
ENGLISH
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
AN-MR500
Magic Remote
AN-WF500
Wi-Fi/Bluetooth Dongle
LG Audio Device
Tag On
AN-VC5**
Video Call Camera
* You can use the Magic Remote and LG Audio Device(Wireless) only when you are using the Wi-Fi/
Bluetooth Dongle.
ASSEMBLING AND PREPARING
A type :
LB49**-ZH, LB57**,
LB58**-ZA/ZB/ZG/ZJ, LB61**
Screen
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
Joystick Button2
B type :
LB49**-ZB/ZG
Screen
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
2
Joystick
Joystick Button
Button2
C type :
LB58**-ZM/ZW
Screen
Speakers
Remote control and
Intelligent1 sensors
Power Indicator
Joystick Button2
ENGLISH
Parts and buttons
13
14
ASSEMBLING AND PREPARING
ENGLISH
1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
2 Joystick Button - This button is located below the TV screen.
NOTE
y y You can set the power indicator light to on or off by selecting OPTION in the main menus.
Using the Joystick button
You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right.
Basic Functions
Power On
When the TV is turned off, place your finger on the joystick button
and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick button
and press it once for a few seconds and release it.
(However, if the Menu button is on the screen, pressing and
holding the joystick button will let you exit the Menu.)
Volume
Control
If you place your finger over the joystick button and move it left or
right, you can adjust the volume level you want.
Programmes
Control
If you place your finger over the joystick button and move it up or
down, you can scrolls through the saved programmes you want.
NOTE
y y When your finger over the joystick button and push it to the up, down, left or right, be careful not to
press the joystick button. If you press the joystick button first, you can not adjust the volume level
and saved programmes.
Adjusting the Menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items( , , ,
)moving the joystick button up, down, left or right.
TV Off
Turns the power off.
Settings
Accesses the main menu.
Close
Clears on-screen displays and returns to TV viewing.
Input List
Changes the input source.
ASSEMBLING AND PREPARING
Please note the following advice to prevent the
TV from being scratched or damaged and for safe
transportation regardless of its type and size.
y y When transporting a large TV, there should
be at least 2 people.
y y When transporting the TV by hand, hold the
TV as shown in the following illustration.
CAUTION
y y Avoid touching the screen at all times, as
this may result in damage to the screen.
y y It is recommended to move the TV in the
box or packing material that the TV originally
came in.
y y Before moving or lifting the TV, disconnect
the power cord and all cables.
y y When holding the TV, the screen should face
away from you to avoid damage.
y y When transporting the TV, do not expose the
TV to jolts or excessive vibration.
y y When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
y y Do not apply excessive pressure to cause
flexing /bending of frame chassis as it may
damage screen.
CAUTION
y y When handling the TV, be careful not to
damage the protruding joystick button.
y y Hold the top and bottom of the TV frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
ENGLISH
Lifting and moving the TV
15
16
ASSEMBLING AND PREPARING
ENGLISH
Setting up the TV
28LB49**-ZH
Image shown may differ from your TV.
1
Attaching the stand
22LB49**-ZH
1
2
B stand base
B stand base
A stand base
A stand base
2
2EA
M4 x L10
ASSEMBLING AND PREPARING
LB49**-ZB/ZG
LB57**, LB58**-ZA/ZB/ZG/ZJ, LB61**
B stand base
1
2
Stand Base
2
M4 x L14
4EA
M4 x L20
(Only 32LB57**,
32LB58**-ZA/ZB/
ZG/ZJ)
ENGLISH
A stand base
1
1
2
17
18
ASSEMBLING AND PREPARING
32/39LB58**-ZM
ENGLISH
3
1
4EA
M4 x L20
1
2EA
M4 x L20
42/47/50/55/60LB58**-ZM/ZW
Stand Body
1
Stand Base
2
4EA
M4 x L20
1
Stand Body
Stand Base
ASSEMBLING AND PREPARING
CAUTION
yy When attaching the stand to the TV
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
NOTE
yy The Rubber will protect the opening
from accumulating dust and dirt. When
installing the wall mounting bracket, use
the Rubber. (Only LB58**-ZM/ZW)
3
Rubber
4EA
M4 x L14
ENGLISH
2
19
20
ASSEMBLING AND PREPARING
ENGLISH
Mounting on a table
1 Lift and tilt the TV into its upright position on a
table.
- - Leave a 10 cm (minimum) space from
the wall for proper ventilation.
Securing the TV to a wall
(This feature is not available for all models.)
10 cm
m
10 c
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
y y Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
- - If there are bolts inserted at the eyebolts position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
y y Make sure that children do not climb on
or hang on the TV.
NOTE
y y Use a platform or cabinet that is strong
and large enough to support the TV
securely.
y y Brackets, bolts and ropes are not
provided. You can obtain additional
accessories from your local dealer.
ASSEMBLING AND PREPARING
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
We recommend the use of LG’s wall mount
bracket.
When you do not use LG’s wall mount bracket,
please use a wall mount bracket where the
device is adequately secured to the wall with
enough space to allow connectivity to external
devices.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described
in the following table.
Separate purchase(Wall Mounting Bracket)
Model
VESA (A x B)
Standard screw
Number of
screws
Wall mount
bracket
Model
22LB49**
75 x 75
M4 X L10
4
28LB49**
100 x 100
M4 X L10
4
LSW140B
LSW140B
32/39LB57**
32/39LB58**
VESA (A x B)
Standard screw
Number of
screws
Wall mount
bracket
200 x 200
M6
4
42/47/50LB57**
42/47/50/55LB58**
47/50/55LB61**
400 x 400
M6
4
LSW240B
MSW240
LSW440B
MSW240
Model
VESA (A x B)
60LB58**
60LB61**
400 x 400
Standard screw
M6
Number of
screws
Wall mount
bracket
4
LSW440B
A
B
ENGLISH
Mounting on a wall
21
22
ASSEMBLING AND PREPARING
ENGLISH
NOTE
CAUTION
y y Disconnect the power first, and then
move or install the TV. Otherwise electric
shock may occur.
y y If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorised LG wall mount and
contact the local dealer or qualified
personnel.
y y Do not over tighten the screws as this
may cause damage to the TV and void
your warranty.
y y Use the screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an
improper accessory are not covered by
the warranty.
y y Screw length from outer surface of
back cover should be under 8mm. (only
LB49**)
y y Use the screws that are listed on the
VESA standard screw specifications.
y y The wall mount kit includes an installation
manual and necessary parts.
y y The wall mount bracket is not provided.
You can obtain additional accessories
from your local dealer.
y y The length of screws may differ
depending on the wall mount. Make sure
to use the proper length.
y y For more information, refer to the manual
supplied with the wall mount.
y y When attaching a wall mounting
bracket to the TV, insert the wall
mount spacers into the TV wall mount
holes to adjust the vertical angle of
the TV. (Only 42LB57**, 42LB58**)
Wall mount Pad
Back Cover
Wall mount Pad
Back Cover
Standard screw
: M4 x L10
Max.8mm
Wall Mount Spacer
MAKING CONNECTIONS
Antenna connection
This section on MAKING CONNECTIONS mainly
uses diagrams for the LB57** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information of external device’s
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
ANTENNA /
CABLE IN
(*Not Provided)
NOTE
y y The external device connection may differ
from the model.
y y Connect external devices to the TV
regardless of the order of the TV port.
y y If you record a TV program on a DVD
recorder or VCR, make sure to connect
the TV signal input cable to the TV
through a DVD recorder or VCR. For
more information of recording, refer to
the manual provided with the connected
device.
y y Refer to the external equipment’s manual
for operating instructions.
y y If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
y y In PC mode, there may be noise
associated with the resolution, vertical
pattern, contrast or brightness. If noise is
present, change the PC output to another
resolution, change the refresh rate to
another rate or adjust the brightness and
contrast on the PICTURE menu until the
picture is clear.
y y In PC mode, some resolution settings
may not work properly depending on the
graphics card.
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
NOTE
y y Use a signal splitter to use more than 2 TVs.
y y If the image quality is poor, install a signal
amplifier properly to improve the image quality.
y y If the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
y y An antenna cable and converter are not
supplied.
y y Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
Satellite dish connection
(Only satellite models)
13/18V
700mA Max
LNB
Satellite IN
(*Not Provided)
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
ENGLISH
MAKING CONNECTIONS
23
24
MAKING CONNECTIONS
Euro Scart connection
(Only LB49**)
AV1
IN/OUT
ENGLISH
Adapter connection
(*Not Provided)
2
3
1
AC-DC Adapter
Transmits the video and audio signals from an
external device to the TV set. Connect the
external device and the TV set with the euro scart
cable as shown.
Output
Type
CAUTION
y y Please be sure to connect the TV to the
AC-DC power adapter before connecting
the TV’s power plug to a wall power
outlet.
Current
input mode
Digital TV
AV1
(TV Out1)
Digital TV
Analogue TV, AV
Component
Analogue TV
HDMI
1 TV Out : Outputs Analogue TV or Digital TV
signals.
NOTE
y y Any Euro scart cable used must be signal
shielded.
MAKING CONNECTIONS
25
Connect your TV to external devices. For the best picture and audio quality, connect the external device
and the TV with the HDMI cable as shown. Some separate cable is not provided.
(Only LB49**)
R
AUDIO OUT
Digital Audio System
RED
L
(MONO)
OPTICAL AUDIO IN
WHITE
DVI OUT
Headphone
DVD / Blu-Ray / HD Cable Box / HD
STB / PC
(Only
satellite
models)
L
L
R
(MONO)
(MONO)
R
L
R
(MONO)
RED
RED
WHITE
BLUE
GREEN
RED
WHITE
YELLOW
MHL passive
cable
RED
WHITE
VIDEO
RED
DVD / Blu-Ray / HD Cable
Box / VCR
BLUE
(MONO)
GREEN
RED
WHITE
YELLOW
VIDEO
AUDIO
DVD/ Blu-Ray / HD
Cable Box
HDMI
DVD/ Blu-Ray / HD Cable
Box / HD STB / PC
Mobile
Phone
ENGLISH
Other connections
26
MAKING CONNECTIONS
ENGLISH
PCMCIA card
USB
HDD
HUB
MAKING CONNECTIONS
27
(Only LB57**, LB58** , LB61**)
ENGLISH
Headphone
H/P OUT
13/18V
700mA Max
LNB
Satellite IN
ANTENNA /
CABLE IN
(Only satellite models)
DVD/ Blu-Ray /
HD Cable Box
RED
WHITE
AUDIO
RED
WHITE
RED
BLUE
VIDEO
RED
BLUE
GREEN
DVD / Blu-Ray / HD Cable
Box / VCR
GREEN
RED
WHITE
YELLOW
(MONO)
RED
WHITE
YELLOW
VIDEO
OPTICAL AUDIO IN
Digital Audio
System
28
MAKING CONNECTIONS
ENGLISH
PCMCIA card
USB
HUB
HDD
MHL passive cable
Mobile Phone
RED
WHITE
AUDIO OUT
DVI OUT
DVD / Blu-Ray / HD Cable Box / HD STB /
PC (Only HDMI IN 1(ARC) or HDMI IN 2)
HDMI
DVD/ Blu-Ray / HD Cable Box / HD STB /
PC (Only HDMI IN 1(ARC) or HDMI IN 2)
REMOTE CONTROL
29
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA)
matching the
and
ends to the label inside the compartment, and close the
battery cover.
To remove the batteries, perform the installation actions in reverse.
ENGLISH
REMOTE CONTROL
or
CAUTION
y y Do not mix old and new batteries, as this may damage the remote control.
y y The remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor on the TV.
(Depending on model)
TV/RAD
Selects Radio, TV and DTV programme.
SUBTITLE Recalls your preferred subtitle in digital mode.
Q. MENU Accesses the quick menus.
GUIDE Shows programme guide.
AD By Pressing AD button, audio descriptions function will be enabled.
TV/
RAD
INPUT
SUBTITLE
Q.MENU
GUIDE
AD
1.@
2 abc
3 def
4 ghi
5 jkl
6 mno
7pqrs
8 tuv
9wxyz
LIST
0
Q.VIEW
INPUT Changes the input source.
LIST Accesses the saved programme list.
(Space) Opens an empty space on the screen keyboard. (Depending
on model)
Q.VIEW Returns to the previously viewed programme.
FAV Accesses your favourite programme list.
INFO
Views the information of the current programme and
screen.
PAGE
Moves to the previous or next screen.
FAV
INFO
P
SETTINGS Accesses the main menus.
MUTE
SETTINGS
1
SMART Accesses the Home menus.
SMART
TEXT
MY APPS
T.OPT
MY APPS Shows the list of Apps.
1
1 TELETEXT BUTTONS These buttons are used for teletext.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
OK
EXIT
LIVE TV
APP/
2
REC/
Selects menus or options and confirms your input.
BACK Returns to the previous level.
EXIT Clears on-screen displays and returns to TV viewing.
APP/ Selects the MHP TV menu source. (Only Italy) (Depending on model)
REC/ Starts to record and displays record menu. (Only Time Machine Ready
supported model)
LIVE TV Returns to LIVE TV.
Control buttons (
) Controls the Premium contents, Time
MachineReady or SmartShare menus or the SIMPLINK compatible devices
Ready
(USB or SIMPLINK or Time Machine
).
(
2 Colour buttons These access special functions in some menus.
: Red,
: Green,
: Yellow,
: Blue)
30
REMOTE CONTROL
(Depending on model)
ENGLISH
SUBTITLE Recalls your preferred subtitle in digital mode.
RATIO Resizes an image.
RATIO
INPUT Changes the input source.
INPUT
TV/
RAD
SUBTITLE
TV/RAD
1.,;@ 2 abc 3 def
(Space) Opens an empty space on the screen keyboard. (Depending on
model)
4 ghi 5 jkl 6 mno
Q.VIEW Returns to the previously viewed programme.
7pqrs 8 tuv 9wxyz
LIST
0
FAV Accesses your favourite programme list.
GUIDE Shows programme guide.
Q.VIEW
PAGE
FAV
P
A
G
E
GUIDE
INFO
SMART
Moves to the previous or next screen.
Views the information of the current programme and screen.
SMART Accesses the Home menus.
MUTE
INFO
Selects Radio, TV and DTV programme.
LIST Accesses the saved programme list.
MY APPS Shows the list of Apps.
MY APPS
Navigation buttons (up/down/left/right) Scrolls through menus or options.
OK
Selects menus or options and confirms your input.
BACK Returns to the previous level.
OK
SETTINGS Accesses the main menus.
EXIT Clears on-screen displays and returns to TV viewing.
BACK
SETTINGS
EXIT
(
1
2
TEXT
T.OPT
LIVE TV
SLEEP
Q.MENU
1 Colour buttons These access special functions in some menus.
: Red,
: Green,
: Yellow,
: Blue)
2 TELETEXT BUTTONS These buttons are used for teletext.
LIVE TV Returns to LIVE TV.
AD
REC/
Q. MENU Accesses the quick menus.
APP/
Control buttons (
) Controls the Premium contents, Time
MachineReady or SmartShare menus or the SIMPLINK compatible devices (USB or
Ready
SIMPLINK or Time Machine
).
REC/ Starts to record and displays record menu. (Only Time Machine Ready
supported model)
SLEEP Sets the sleep timer.
AD By Pressing AD button, audio descriptions function will be enabled.
APP/ Selects the MHP TV menu source. (Only Italy) (Depending on model)
MAGIC REMOTE FUNCTIONS
31
ENGLISH
MAGIC REMOTE FUNCTIONS
This item is not included for all models.
When the message “Magic Remote battery is low. Change the battery.” is
displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA)
matching
and
ends to the label inside the compartment, and close the
battery cover. Be sure to point the remote control toward the remote control
sensor on the TV.
To remove the batteries, perform the installation actions in reverse.
CAUTION
y y Do not mix old and new batteries, as this may damage the remote control.
(Only LB585*)
(POWER)
Turns the TV on or off.
Navigation buttons
(up/down/left/right)
Press the up, down, left or right
button to scroll the menu.If you
press , , or buttons while
the pointer is in use, the pointer
will disappear from the screen
and Magic Remote will operate
like a general remote control. To
display the pointer on the screen
again, shake Magic Remote to
the left and right.
Wheel(OK)
Press the center of the Wheel
button to select a menu. You can
change programmes and scroll
the menu by using the Wheel
button.
Coloured buttons
These access special functions in
some menus.
(
: Red,
: Green,
: Yellow,
: Blue)
Adjusts the volume level.
(BACK)
Returns to the previous level.
(Home)
Accesses the Home menu.
(EXIT to LIVE)
Swiches among broadcast
(antenna) and various inputs.
(Voice recognition)
(Depending on model)
P
Scrolls through the saved
programmes.
/ INPUT
Displays the Screen Remote.
* Accesses the Universal Control
Menu. (Depending on model)
* Pressing and holding the
/ INPUT button will
display a menu to select
an external device that is
connected to the TV.
Used for viewing 3D video.
(Only 3D models)
(MUTE)
Mutes all sounds.
* By Pressing and holding the
button, audio descriptions
function will be enabled.
(Depending on model)
32
MAGIC REMOTE FUNCTIONS
How to deregister the Magic Remote
ENGLISH
Voice recognition(Depending on model)
Network connection is required to use the
voice recognition function.
(BACK)
1 .
2 .
(Home)
Press the Voice recognition button.
Speak when the voice display window
appears on the left of the TV screen.
• The voice recognition may fail when
you speak too fast or too slow.
• Use the Magic Remote no further than
10 cm from your face.
• The recognition rate may
vary depending on the user’s
characteristics (voice, pronunciation,
intonation and speed) and the
environment (noise and TV volume).
Registering Magic Remote
BACK
How
HOME
to register
the Magic Remote
To use the Magic Remote, first
pair it with your TV.
P
MY APPS
1 Put batteries into the Magic
Remote and turn the TV on.
2 Point the Magic Remote at your
TV and press the Wheel (OK)
on the remote control.
» »If the TV fails to register the
Magic Remote, try again
after turning the TV off and
back on.
Press the
(BACK) and
(Home) buttons at the same time,
for five seconds, to unpair the
Magic Remote with your TV.
» »Pressing and holding the
(EXIT to LIVE) button will
let you cancel and re-register
Magic Remote at once.
How to use Magic Remote
y y Shake the Magic Remote
slightly to the right and left or
press
(Home),
/
INPUT,
buttons to make
the pointer appear on the
screen.
» »The pointer will appear when
you turn the Wheel button.
(Depending on model)
y y If the pointer has not been
used for a certain period
of time or Magic Remote is
placed on a flat surface, then
the pointer will disappear.
y y If the pointer is not
responding smoothly, you can
reset the pointer by moving it
to the edge of the screen.
y y The Magic Remote depletes
batteries faster than a normal
remote due to the additional
features.
MAGIC REMOTE FUNCTIONS / USING THE USER GUIDE
y yUse the remote control within the specified
range (within 10 m).
You may experience communication
failures when using the device outside the
coverage area or if there are obstacles
within the coverage area.
y yYou may experience communication
failures depending on the accessories.
Devices such as a microwave oven
and wireless LAN operate in the same
frequency band (2.4 GHz) as the Magic
Remote. This may cause communication
failures.
y yThe Magic Remote may not work properly
if a wireless router (AP) is within 1 meter
of the TV. Your wireless router should be
more than 1 m away from the TV.
y yDo not disassemble or heat the battery.
y yDo not drop the battery. Avoid avoid
extreme shocks to the battery.
y yInserting the battery the wrong way may
result in explosion.
USING THE USER
GUIDE
User Guide allows you to more easily access the
detailed TV information.
1 Press the
SMART button to access the
Home menu.
2 Select SETTINGS → SUPPORT.
3 Select User Guide and press OK .
SUPPORT
Software Update
Picture Test
Sound Test
Signal Test
Product/Service Info.
Initialization of App
User Guide
ENGLISH
Precautions to Take when
Using the Magic Remote
33
34
MAINTENANCE / TROUBLESHOOTING
ENGLISH
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
y y Make sure to turn the power off and disconnect the power cord and all other cables first.
y y When the TV is left unattended and unused for a long time, disconnect the power cord from the
wall outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
y y To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
y y To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
y y Avoid touching the screen at all times, as this may result in damage to the screen.
y y Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result
in scratches and image distortions.
y y Do not use any chemicals as this may damage the product.
y y Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem
Solution
Cannot control
the TV with the
remote control.
y y Check the remote control sensor on the product and try again.
y y Check if there is any obstacle between the product and the remote control.
to
,
y y Check if the batteries are still working and properly installed (
to
).
No image display
and no sound is
produced.
y y Check if the product is turned on.
y y Check if the power cord is connected to a wall outlet.
y y Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
y y Check the power control settings. The power supply may be interrupted.
y y Check if the Automatic Standby (Depending on model) / Sleep Timer /
Time Power Off is activated in the TIME settings.
y y If there is no signal while the TV is on, the TV will turn off automatically after
15 minutes of inactivity.
When connecting
to the PC (HDMI/
DVI), ‘No signal’
or ‘Invalid Format’
is displayed.
y y Turn the TV off/on using the remote control.
y y Reconnect the HDMI cable.
y y Restart the PC with the TV on.
SPECIFICATIONS
(Depending on model)
Wireless LAN module(TWFM-B006D) specification
Standard
IEEE802.11a/b/g/n
Frequency Range
Output Power
(Max.)
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
802.11a: 11 dBm
802.11b: 14 dBm
802.11g: 10.5 dBm
802.11n - 2.4GHz: 11 dBm
802.11n - 5GHz: 12.5 dBm
y yBecause band channel used by the country could be different, the user can not change or adjust the
operating frequency and this product is set for the regional frequency table.
y yThis device should be installed and operated with minimum distance 20 cm between the device and
your body. And this phrase is for the general statement for consideration of user environment.
0197
0197
ENGLISH
SPECIFICATIONS
35
36
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
ENGLISH
22LB49**
MODELS
22LB490B-ZG
22LB490U-ZG
22LB491U-ZB
22LB498U-ZG
22LB4900-ZA
22LB490B-ZH
22LB490U-ZA
22LB490U-ZH
22LB490V-ZA
506 x 354 x 140.6
506 x 345 x 129
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
3.2
3.1
Without stand (kg)
3.0
3.0
Without stand(mm) 506 x 311.7 x 55.8
506 x 311.7 x 55.8
Power requirement
19 V
Power consumption
42 W
2.0 A
19 V
AC-DC Adaptor
Manufacturer : Lien Chang
Model : LCAP35
Manufacturer : APD
Model : DA-48F19
2.0 A
42 W
In: AC 100-240 V~ 50/60 Hz
Out: 19 V
2.53 A
28LB49**
28LB490B-ZG
28LB490U-ZG
28LB491U-ZB
28LB498U-ZG
28LB4900-ZA
28LB490B-ZH
28LB490U-ZA
28LB490U-ZH
28LB490V-ZA
638 x 430 x 175
638 x 422 x 160
Without stand(mm) 638 x 389 x 56.8
638 x 389 x 56.8
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
4.6
Without stand (kg)
4.3
4.4
4.3
Power requirement
19 V
2.7 A
Power consumption
55 W
AC-DC Adaptor
Manufacturer : Lien Chang
Model : LCAP39
Manufacturer : APD
Model : DA-65G19
55 W
In: AC 100-240 V~ 50/60 Hz
Out: 19 V
19 V
3.42 A
2.7 A
SPECIFICATIONS
39LB57**
42LB57**
32LB5700-ZB
32LB5700-ZK
32LB570B-ZB
32LB570B-ZK
32LB570U-ZB
32LB570U-ZJ
32LB570U-ZK
32LB570V-ZB
32LB570V-ZF
32LB570V-ZJ
32LB570V-ZK
32LB572U-ZP
32LB572V-ZP
39LB5700-ZB
39LB5700-ZK
39LB570B-ZB
39LB570B-ZK
39LB570U-ZB
39LB570U-ZJ
39LB570U-ZK
39LB570V-ZB
39LB570V-ZF
39LB570V-ZJ
39LB570V-ZK
39LB572U-ZP
39LB572V-ZP
42LB5700-ZB
42LB5700-ZK
42LB570B-ZB
42LB570B-ZK
42LB570U-ZB
42LB570U-ZJ
42LB570U-ZK
42LB570V-ZB
42LB570V-ZF
42LB570V-ZJ
42LB570V-ZK
42LB572U-ZP
42LB572V-ZP
732 x 481 x 207
885 x 567 x 218
961 x 610 x 218
885 x 524 x 55.5
961 x 567 x 55.5
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
6.2
8.3
9.5
Without stand (kg)
6.0
8
9.2
Without stand(mm) 732 x 437 x 55.5
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
75 W
100 W
47LB57**
50LB57**
47LB5700-ZB
47LB5700-ZK
47LB570B-ZB
47LB570B-ZK
47LB570U-ZB
47LB570U-ZJ
47LB570U-ZK
47LB570V-ZB
47LB570V-ZF
47LB570V-ZJ
47LB570V-ZK
47LB572U-ZP
47LB572V-ZP
50LB5700-ZB
50LB5700-ZK
50LB570B-ZB
50LB570B-ZK
50LB570U-ZB
50LB570U-ZJ
50LB570U-ZK
50LB570V-ZB
50LB570V-ZF
50LB570V-ZJ
50LB570V-ZK
50LB572U-ZP
50LB572V-ZP
1073 x 676 x 255
1128 x 708 x 255
Without stand(mm) 1073 x 629 x 55.8
1128 x 660 x 55.8
MODELS
Dimensions
(W x H x D)
Weight
With stand (mm)
With stand (kg)
12.7
14.2
Without stand (kg)
12.3
13.8
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
120 W
130 W
110 W
ENGLISH
MODELS
32LB57**
37
38
SPECIFICATIONS
ENGLISH
32LB58**
MODELS
Dimensions
(W x H x D)
Weight
With stand (mm)
32LB580V-ZA
32LB580U-ZB
32LB580V-ZB
32LB580V-ZD
32LB5820-ZJ
32LB582B-ZJ
32LB582U-ZJ
32LB582V-ZJ
32LB582V-ZG
32LB5800-ZM
32LB580B-ZM
32LB580U-ZM
32LB580V-ZM
32LB585V-ZM
732 x 481 x 207
732 x 475 x 233
Without stand(mm) 732 x 437 x 55.5
732 x 437 x 55.5
With stand (kg)
6.2
8.1
Without stand (kg)
6.0
6.0
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
75 W
75 W
39LB58**
39LB580V-ZA
39LB580U-ZB
39LB580V-ZB
39LB580V-ZD
39LB5820-ZJ
39LB582B-ZJ
39LB582U-ZJ
39LB582V-ZJ
39LB582V-ZG
MODELS
885 x 567 x 218
39LB5800-ZM
39LB580B-ZM
39LB580U-ZM
39LB580V-ZM
39LB585V-ZM
885 x 564 x 238
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
8.3
10.4
Without stand (kg)
8
8
Without stand(mm) 885 x 524 x 55.5
885 x 524 x 55.5
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
100 W
100 W
42LB58**
MODELS
42LB580V-ZA
42LB580U-ZB
42LB580V-ZB
42LB580V-ZD
42LB5820-ZJ
42LB582B-ZJ
42LB582U-ZJ
42LB582V-ZJ
42LB582V-ZG
42LB5800-ZM
42LB580B-ZM
42LB580U-ZM
42LB580V-ZM
42LB585V-ZM
42LB588V-ZW
961 x 610 x 218
961 x 607 x 238
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
9.5
11.7
Without stand (kg)
9.2
9.2
Without stand(mm) 961 x 567 x 55.5
961 x 567 x 55.5
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
110 W
110 W
SPECIFICATIONS
47LB5800-ZM
47LB580B-ZM
47LB580U-ZM
47LB580V-ZM
47LB585V-ZM
47LB588V-ZW
1073 x 676 x 255
1073 x 670 x 267
Without stand(mm) 1073 x 629 x 55.8
1073 x 629 x 55.8
MODELS
Dimensions
(W x H x D)
Weight
With stand (mm)
With stand (kg)
12.7
15.5
Without stand (kg)
12.3
12.3
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
120 W
120 W
50LB58**
50LB580V-ZA
50LB580U-ZB
50LB580V-ZB
50LB580V-ZD
50LB5820-ZJ
50LB582B-ZJ
50LB582U-ZJ
50LB582V-ZJ
50LB582V-ZG
50LB5800-ZM
50LB580B-ZM
50LB580U-ZM
50LB580V-ZM
50LB585V-ZM
50LB588V-ZW
1128 x 708 x 255
1128 x 703 x 267
Without stand(mm) 1128 x 660 x 55.8
1128 x 660 x 55.8
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
14.2
17
Without stand (kg)
13.8
13.8
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
130 W
130 W
55LB58**
55LB580V-ZA
55LB580U-ZB
55LB580V-ZB
55LB580V-ZD
55LB5820-ZJ
55LB582B-ZJ
55LB582U-ZJ
55LB582V-ZJ
55LB582V-ZG
55LB5800-ZM
55LB580B-ZM
55LB580U-ZM
55LB580V-ZM
55LB585V-ZM
55LB588V-ZW
1243 x 772 x 255
1243 x 766 x 293
Without stand(mm) 1243 x 725 x 56.8
1243 x 725 x 56.8
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
17.7
21.6
Without stand (kg)
17.3
17.3
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
140 W
140 W
ENGLISH
47LB58**
47LB580V-ZA
47LB580U-ZB
47LB580V-ZB
47LB580V-ZD
47LB5820-ZJ
47LB582B-ZJ
47LB582U-ZJ
47LB582V-ZJ
47LB582V-ZG
39
40
SPECIFICATIONS
ENGLISH
60LB58**
47LB61**
50LB61**
60LB5800-ZM
60LB580B-ZM
60LB580U-ZM
60LB580V-ZM
60LB585V-ZM
60LB588V-ZW
47LB610V-ZU
50LB610V-ZU
1373 x 838 x 293
1073 x 676 x 255
1128 x 708 x 255
Without stand(mm) 1373 x 801 x 58.8
1073 x 629 x 55.8
1128 x 660 x 55.8
MODELS
Dimensions
(W x H x D)
With stand (mm)
Weight
With stand (kg)
27.3
12.7
14.2
Without stand (kg)
23.0
12.3
13.8
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power consumption
150 W
120 W
130 W
55LB61**
60LB61**
55LB610V-ZU
60LB610V-ZU
1243 x 772 x 255
1373 x 848 x 280
Without stand(mm) 1243 x 725 x 56.8
1373 x 801 x 58.8
MODELS
Dimensions
(W x H x D)
Weight
With stand (mm)
With stand (kg)
17.7
23.5
Without stand (kg)
17.3
23.0
Power requirement
AC 100-240 V~ 50 / 60 Hz AC 100-240 V~ 50 / 60 Hz
Power consumption
140 W
CI Module Size (W x H x D)
150 W
100.0 mm x 55.0 mm x 5.0 mm
Operating Temperature
Environment
condition
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Digital TV
(Depending on model)
Analogue TV
(Depending on model)
Television system
DVB-T(DVB-T/T2*)
DVB-C
DVB-S/S2*
PAL/SECAM B/G/I/D/K
SECAM L/L’
Programme coverage
VHF, UHF
C-Band*, Ku-Band*
VHF, UHF, CATV
Maximum number of
storable programmes
DVB-S/S2 : 6,000
DVB-T/T2/C & Analogue TV : 1,500
External antenna impedance
75 Ω
* Only DVB-T2/C/S2 support models.
Please contact LG First.
If you have any inquiries or comments,
please contact LG customer information centre.
LG Customer Information Centre
Country
Record the model number and serial number of
the TV.
Refer to the label on the back cover and quote
this information to your dealer when requiring
any service.
Country
Service
Service
0 810 144 131
0900 543 5454
015 200 255
800 187 40
0032 15 200255
801 54 54 54
07001 54 54
808 78 54 54
810 555 810
031 228 3542
8088 5758
0850 111 154
0800 0 54 54
3220
902 500 234
54
0770 54 54 54
01806-11-54-11
(0,20€ pro Anruf
aus dem Festnetz der
DTAG; Mobilfunk: max.
0,60€ pro Anruf.)
MODEL
SERIAL
Latvija
0848 543 543
801 11 200 900,
210 4800 564
0344 847 5454
06 40 54 54 54
800 9990
01 686 9454
0 800 303 000
199600099
8 820 0071 1111
8 8000 805 805,
2255(GSM)
80200201
8 800 120 2222
880008081
8 0000 710 005
8 800 200 7676
Download PDF

advertising