LG | 55EC930V | LG 55EC930V Owner’s Manual

OWNER’S MANUAL
Please read this manual carefully before operating your set and retain it
for future reference.
EC93**
EC97**
EC98**
*MFL68488304*
www.lg.com
P/NO : MFL68488304 (1407-REV00)
Printed in Korea
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
LICENSES
37 REMOTE CONTROL
3
OPEN SOURCE SOFTWARE
NOTICE
39 MAGIC REMOTE FUNCTIONS
3
EXTERNAL CONTROL DEVICE
SETUP
4
SAFETY INSTRUCTIONS
10
- Viewing 3D Imaging
12 INSTALLATION PROCEDURE
12 ASSEMBLING AND
PREPARING
12
14
15
17
18
19
19
20
20
21
22
23
24
26
26
27
27
Unpacking
Separate purchase
Parts and buttons
- Using the joystick button
Lifting and moving the TV
Setting up the TV
- Detaching the stand
- Assembling the AV cover
Mounting on a table
Mounting on a wall
Wall Type Set-up Guide
- How to detach the stand
Tidying cables
Using Built-in Camera
- Preparing Built-in Camera
- Name of Parts of Built-in camera
- Checking the Camera’s Shooting Range
28 MAKING CONNECTIONS
28
29
29
30
31
32
33
33
34
34
34
35
36
Antenna Connection
Satellite dish Connection
HDMI Connection
DVI to HDMI Connection
MHL Connection
Component Connection
Composite Connection
Headphone Connection
Audio Connection
- Digital optical audio connection
USB Connection
CI module Connection
Euro Scart Connection
40
40
41
Registering Magic Remote
How to use magic remote
Precautions to Take when Using the Magic
Remote
41 USING THE USER GUIDE
42 MAINTENANCE
42
42
42
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
43 TROUBLESHOOTING
44 SPECIFICATIONS
WARNING
yy If you ignore the warning message, you
may be seriously injured or there is a
possibility of accident or death.
CAUTION
yy If you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
yy The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE / EXTERNAL CONTROL DEVICE SETUP
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
EXTERNAL CONTROL DEVICE SETUP
To obtain the external control device setup information, please visit www.lg.com.
ENGLISH
ENG
LICENSES
4
SAFETY INSTRUCTIONS
ENG
ENGLISH
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
yy
Do not place the TV and/or remote control in the following environments:
--A location exposed to direct sunlight
--An area with high humidity such as a bathroom
--Near any heat source such as stoves and other devices that produce heat
--Near kitchen counters or humidifiers where they can easily be exposed to steam
or oil
--An area exposed to rain or wind
--Near containers of water such as vases
Otherwise, this may result in fire, electric shock, malfunction or product deformation.
yy
Do not place the product where it might be exposed to dust.
This may cause a fire hazard.
yy
Mains Plug is the TV connecting/disconnecting device to AC mains electric supply.
This plug must remain readily attached and operable when TV is in use.
Do not touch the power plug with wet hands. Additionally, if the cord pin is wet or
yy
covered with dust, dry the power plug completely or wipe dust off.
You may be electrocuted due to excess moisture.
yy
Make sure to connect Mains cable to compliant AC mains socket with Grounded
earth pin. (Except for devices which are not grounded on earth.)
Otherwise possibility you may be electrocuted or injured.
yy
Insert power cable plug completely into wall socket otherwise if not secured completely into socket, fire ignition may break out.
yy
Ensure the power cord does not come into contact with hot objects such as a
heater.
This may cause a fire or an electric shock hazard.
yy
Do not place a heavy object, or the product itself, on power cables.
Otherwise, this may result in fire or electric shock.
yy
Bend antenna cable between inside and outside building to prevent rain from flowing in.
This may cause water damaged inside the Product and could give an electric
shock.
When mounting TV onto wall make sure to neatly install and isolate cabling from
yy
rear of TV as to not create possibility of electric shock/fire hazard.
SAFETY INSTRUCTIONS
yy
Do not drop the product or let it fall over when connecting external devices.
Otherwise, this may result in injury or damage to the product.
yy
Keep the anti-moisture packing material or vinyl packing out of the reach of children.
Anti-moisture material is harmful if swallowed. If swallowed by mistake, force the
patient to vomit and visit the nearest hospital. Additionally, vinyl packing can cause
suffocation. Keep it out of the reach of children.
yy
Do not let your children climb or cling onto the TV.
Otherwise, the TV may fall over, which may cause serious injury.
yy
Dispose of used batteries carefully to ensure that a small child does not consume
them.
Please seek Doctor- Medical Attention immediately if child consumes batteries.
yy
Do not insert any metal objects/conductors (like a metal chopstick/cutlery/screwdriver) between power cable plug and input Wall Socket while it is connected to
the input terminal on the wall. Additionally, do not touch the power cable right after
plugging into the wall input terminal.
You may be electrocuted.
(Depending on model)
yy
Do not put or store inflammable substances near the product.
There is a danger of combustion/explosion or fire due to careless handling of the
inflammable substances.
yy
Do not drop metallic objects such as coins, hair pins, chopsticks or wire into the
product, or inflammable objects such as paper and matches. Children must pay
particular attention.
Electrical shock, fire or injury can occur. If a foreign object is dropped into the product, unplug the power cord and contact the service centre.
yy
Do not spray water on the product or scrub with an inflammable substance (thinner
or benzene). Fire or electric shock accident can occur.
yy
Do not allow any impact, shock or any objects to fall into the unit, and do not drop
anything onto the screen.
You may be injured or the product can be damaged.
yy
Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.
yy
Never touch the wall outlet when there is leakage of gas, open the windows and
ventilate.
It may cause a fire or a burn by a spark.
ENGLISH
ENG
yy
Do not plug too many electrical devices into a single multiple electrical outlet.
Otherwise, this may result in fire due to over-heating.
5
6
SAFETY INSTRUCTIONS
ENG
ENGLISH
yy
Do not disassemble, repair or modify the product at your own discretion.
Fire or electric shock accident can occur.
Contact the service centre for check, calibration or repair.
yy
If any of the following occur, unplug the product immediately and contact your local
service centre.
--The product has been impacted by shock
--The product has been damaged
--Foreign objects have entered the product
--The product produced smoke or a strange smell
This may result in fire or electric shock.
yy
Unplug the TV from AC mains wall socket if you do not intend to use the TV for a
long period of time.
Accumulated dust can cause fire hazard and insulation deterioration can cause
electric leakage/shock/fire.
yy
Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
SAFETY INSTRUCTIONS
yy
Install the product where no radio wave occurs.
yy
There should be enough distance between an outside antenna and power lines to
keep the former from touching the latter even when the antenna falls.
This may cause an electric shock.
yy
Do not install the product on places such as unstable shelves or inclined surfaces.
Also avoid places where there is vibration or where the product cannot be fully
supported.
Otherwise, the product may fall or flip over, which may cause injury or damage to
the product.
yy
If you install the TV on a stand, you need to take actions to prevent the product
from overturning. Otherwise, the product may fall over, which may cause injury.
yy
If you intend to mount the product to a wall, attach VESA standard mounting interface (optional
parts) to the back of the product. When you install the set to use the wall mounting bracket (optional
parts), fix it carefully so as not to drop.
yy
Only use the attachments / accessories specified by the manufacturer.
yy
When installing the antenna, consult with a qualified service technician. If not
installed by a qualified technician, this may create a fire hazard or an electric shock
hazard.
yy
We recommend that you maintain a distance of at least 2 to 7 times the diagonal
screen size when watching TV.
If you watch TV for a long period of time, this may cause blurred vision.
yy
Only use the specified type of battery.
This could cause damage to the remote control.
yy
Do not mix new batteries with old batteries.
This may cause the batteries to overheat and leak.
yy
Batteries should not be exposed to excessive heat. For example, keep away from direct sunlight,
open fireplace and electric heaters .
yy
Do not place non-rechargeable batteries in charging device.
yy
Make sure there are no objects between the remote control and its sensor.
yy
Signal from Remote Control can be interrupted due to external/internal lighting eg
Sunlight, fluorescent lighting.
If this occurs turn off lighting or darken viewing area.
yy
When connecting external devices such as video game consoles, make sure the
connecting cables are long enough.
Otherwise, the product may fall over, which may cause injury or damage the product.
ENGLISH
ENG
CAUTION
7
8
SAFETY INSTRUCTIONS
ENG
ENGLISH
yy
Do not turn the product On/Off by plugging-in or unplugging the power plug to the
wall outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an electric shock.
yy
Please follow the installation instructions below to prevent the product from overheating.
--The distance between the product and the wall should be more than 10 cm.
--Do not install the product in a place with no ventilation (e.g., on a bookshelf or in
a cupboard).
--Do not install the product on a carpet or cushion.
--Make sure the air vent is not blocked by a tablecloth or curtain.
Otherwise, this may result in fire.
yy
Take care not to touch the ventilation openings when watching the TV for long periods as the ventilation openings may become hot. This does not affect the operation or performance of the product.
yy
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
yy
Prevent dust collecting on the power plug pins or outlet.
This may cause a fire hazard.
yy
Protect the power cord from physical or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the appliance.
yy
Do not press strongly upon the panel with a hand or sharp object such as nail,
pencil or pen, or make a scratch on it, as it may cause damage to screen.
yy
Avoid touching the screen or holding your finger(s) against it for long periods of
time. Doing so may produce some temporary or permanent distortion/damage to
screen.
yy
When cleaning the product and its components, unplug the power first and wipe it
with a soft cloth. Applying excessive force may cause scratches or discolouration.
Do not spray with water or wipe with a wet cloth. Never use glass cleaner, car or
industrial shiner, abrasives or wax, benzene, alcohol etc., which can damage the
product and its panel.
Otherwise, this may result in fire, electric shock or product damage (deformation,
corrosion or breakage).
yy
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
yy
When unplugging the cable, grab the plug and unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power cord from the power board, as this could
be hazardous.
yy
When moving the product, make sure you turn the power off first. Then, unplug the
power cables, antenna cables and all connecting cables.
The TV set or power cord may be damaged, which may create a fire hazard or
cause electric shock.
SAFETY INSTRUCTIONS
yy
Contact the service centre once a year to clean the internal parts of the product.
Accumulated dust can cause mechanical failure.
yy
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
yy
If the product feels cold to the touch, there may be a small “flicker” when it is
turned on. This is normal, there is nothing wrong with product.
yy
The panel is a high technology display product with resolution of two million to six
million pixels. You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and
does not affect the performance and reliability of the product.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
yy
You may find different brightness and colour of the panel depending on your viewing position(left/right/top/down).
This phenomenon occurs due to the characteristic of the panel. It is not related
with the product performance, and it is not malfunction.
yy
Displaying a still image (e.g., broadcasting channel logo, on-screen menu, scene from a video game
or computer screen) for a prolonged time may cause damage to the screen, resulting in retention
of the image, which is known as image sticking. It can remain for long time or never disappear.
The warranty does not cover the product for image sticking. Avoid displaying a fixed image on your
television’s screen for a prolonged period (1 or more hours for OLED).
Also, if you watch the TV at a ratio of 4:3 for a long time, image sticking may occur on the borders of
the panel.
This phenomenon also occurs in third-party products and is not subject to exchange or refund.
yy
Generated Sound
“Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by
plastic thermal contraction due to tempera-ture and humidity. This noise is common for products
where thermal deformation is required. Electrical circuit humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit, which supplies a large amount of current to operate a
product. It varies depending on the product.
This generated sound does not affect the performance and reliability of the product.
ENGLISH
ENG
yy
When moving or unpacking the product, work in pairs because the product is
heavy.
Otherwise, this may result in injury.
9
10 SAFETY INSTRUCTIONS
ENG
ENGLISH
Viewing 3D Imaging
WARNING
Viewing Environment
yy Viewing Time
-- When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a long
period of time may cause headache, dizziness, fatigue or eye strain.
Those that have a photosensitive seizure or chronic illness
yy Some users may experience a seizure or other abnormal symptoms when they are exposed to a
flashing light or particular pattern from 3D contents.
yy Do not watch 3D videos if you feel nausea, are pregnant and/ or have a chronic illness such as epilepsy,
cardiac disorder, or blood pressure disease, etc.
yy 3D Contents are not recommended to those who suffer from stereo blindness or stereo anomaly. Double
images or discomfort in viewing may be experienced.
yy If you have strabismus (cross-eyed), amblyopia (weak eyesight) or astigmatism, you may have trouble
sensing depth and easily feel fatigue due to double images. It is advised to take frequent breaks than
the average adult.
yy If your eyesight varies between your right and left eye, revise your eyesight prior to watching 3D
contents.
Symptoms which require discontinuation or refraining from watching 3D contents
yy Do not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking.
yy When these symptoms are experienced, stop using/watching 3D contents and get enough rest until the
symptom subsides.
-- Consult your doctor when the symptoms persist. Symptoms may include headache, eyeball pain,
dizziness, nausea, palpitation, blurriness, discomfort, double image, visual inconvenience or fatigue.
SAFETY INSTRUCTIONS
11
Viewing Environment
yy Viewing Distance
-- Maintain a distance of at least twice the screen diagonal length when watching 3D contents. If you
feel discomfort in viewing 3D contents, move further away from the TV.
Viewing Age
yy Infants/Children
-- Usage/ Viewing 3D contents for children under the age of 6 are prohibited.
-- Children under the age of 10 may overreact and become overly excited because their vision is in
development (for example: trying to touch the screen or trying to jump into it. Special monitoring
and extra attention is required for children watching 3D contents.
-- Children have greater binocular disparity of 3D presentations than adults because the distance
between the eyes is shorter than one of adults. Therefore they will perceive more stereoscopic
depth compared to adults for the same 3D image.
yy Teenagers
-- Teenagers under the age of 19 may react with sensitivity due to stimulation from light in 3D
contents. Advise them to refrain from watching 3D contens for a long time when they are tired.
yy Elderly
-- The elderly may perceive less 3D effect compared to the youth. Do not sit closer to the TV than the
recommended distance.
Cautions when using the 3D glasses
yy Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly.
yy Do not use 3D glasses instead of your normal glasses, sunglasses or protective goggles.
yy Using modified 3D glasses may cause eye strain or image distortion.
yy Do not keep your 3D glasses in extremely high or low temperatures. It will cause deformation.
yy The 3D glasses are fragile and are easily scratched. Always use a soft, clean piece of cloth when wiping
the lenses. Do not scratch the lenses of the 3D glasses with sharp objects or clean/wipe them with
chemicals.
ENGLISH
ENG
CAUTION
12 INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
Image shown may differ from your TV.
yy
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy
The available menus and options may differ from the input source or product model that you are using.
yy
New features may be added to this TV in the future.
yy
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
yy
be turned off if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the picture
yy
is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Connect an external device to the TV set.
3 Make sure the network connection is available.
You can use the TV network functions only when the network connection is made.
* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may take a few
minutes.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product.
The illustrations in this manual may differ from the actual product and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved items are not covered by the warranty.
yy
Some models have a thin film attached on to the screen and this must not be removed.
yy
NOTE
The items supplied with your product may vary depending on the model.
yy
Product specifications or contents of this manual may be changed without prior notice due to upgrade
yy
of product functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
yy
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory
stick does not fit into your TV’s USB port.
B
B
A
A
A<
= 10 mm
B<
= 18 mm
ASSEMBLING AND PREPARING 13
ENGLISH
ENG
Remote control,
Batteries (AAA)
(Depending on model)
(See p. 37, 38)
Magic remote,
Batteries (AA)
(See p. 39)
Owner’s manual
Cinema 3D glasses
The number of 3D
glasses may differ
depending on the model
or country.
Cable Holder
(See p. 24, 25)
Component gender
cable
(See p. 32)
Composite gender
cable
(See p. 32, 33)
HDMI Cable
(Only EC97**, EC98**)
(See p. 29)
Scart Gender Cable
(See p. 36)
AV Cover
(Only EC98**)
(See p. 20)
AV Cover
(Only EC93**)
(See p. 20)
AV Cover
(Only EC97**)
(See p. 20)
P P
Tag On
Tag on
(Depending on model)
Cable Managements
2 EA
(Only EC97**)
(See p. 24, 25)
Cable Management
Screws
2 EA, M4 x L10
(Only EC97**)
(See p. 25)
Cleaning Cloth
(Depending on model)
14 ASSEMBLING AND PREPARING
ENG
ENGLISH
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AG-F***
Cinema 3D Glasses
AN-MR500
Magic Remote
LG Audio Device
Tag On
Compatibility
AN-VC5**
Video call camera
AG-F***DP
Dual Play Glasses
EC93**
EC97**
EC98**
AG-F***
Cinema 3D Glasses
•
•
•
AN-MR500
Magic Remote
•
•
•
AN-VC5**
Video call camera
•
AG-F***DP
Dual Play Glasses
•
•
•
LG Audio Device
•
•
•
Tag On
•
•
•
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s circumstances or policies.
ASSEMBLING AND PREPARING 15
A type: EC93**
<Front>
<Rear>
Screen
Speakers
Remote Control Sensor
and Intelligent Sensor1
LG Logo Light
Joystick button2
B type: EC97**
Built-In Camera
Screen
Speakers
Remote Control Sensor
and Intelligent Sensor1
LG Logo Light
Joystickbutton
button3 3
Joystick
ENGLISH
ENG
Parts and buttons
16 ASSEMBLING AND PREPARING
ENG
ENGLISH
C type: EC98**
<Rear>
<Front>
Built-In Camera
Screen
Speakers
LG Logo Light
Remote Control Sensor
and Intelligent Sensor1
Joystick button2
1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment.
2 Joystick Button - This button is located behind the TV screen.
3 Joystick Button - This button is located below the TV screen.
NOTE
You can set the LG Logo Light to on or off by selecting GENERAL in the main menus.
yy
ASSEMBLING AND PREPARING 17
You can operate the TV by pressing the button or moving the joystick left, right, up, or down.
Basic Functions
Power On
When the TV is turned off, place your finger on the joystick button
and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick button
and press it once for a few seconds and release it.
Volume
Control
If you place your finger over the joystick button and move it left or
right, you can adjust the volume level you want.
Programmes
Control
If you place your finger over the joystick button and move it up or
down, you can scrolls through the saved programmes you want.
NOTE
yy When your finger over the joystick button and push it to the up, down, left or right, be careful not
to press the joystick button. If you press the joystick button first, you may not be able to adjust the
volume level and saved programmes.
Adjusting the Menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items ( , , ) moving the joystick button left or right.
TV OFF
Turns the power off.
CLOSE
Clears on-screen displays and returns to TV viewing.
INPUT
Changes the input source.
ENGLISH
ENG
Using the joystick button
18 ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and moving the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for safe
transportation regardless of its type and size.
When transporting a large TV, there should be
yy
at least 2 people.
When transporting the TV by hand, hold the
yy
TV as shown in the following illustration.
CAUTION
yy
Avoid touching the screen at all times, as this
may result in damage to the screen.
It is recommended to move the TV in the box
yy
or packing material that the TV originally came
in.
Before moving or lifting the TV, disconnect the
yy
power cord and all cables.
When holding the TV, the screen should face
yy
away from you to avoid damage.
yy Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
When transporting the TV, do not expose the
yy
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
yy
upright, never turn the TV on its side or tilt
towards the left or right.
Do not apply excessive pressure to cause
yy
flexing/bending of frame chassis as it may
damage screen.
Be sure to keep your TV upright instead of
yy
laying or tilting it while moving the TV.
When handling the TV, be careful not to
yy
damage the protruding joystick button.
ASSEMBLING AND PREPARING 19
(Only EC97**)
Image shown may differ from your TV.
1
ENGLISH
ENG
Setting up the TV
Back cover
Detaching the stand
(Only EC93**, EC98**)
1
Screen
8 EA
M4 x L20
(Only EC93**)
4 EA
M4 x L20
(Only EC98**)
8EA
M4 x L20
Back cover
2
Screen
2
CAUTION
yy
When detaching the stand to the TV set,
place the screen(or back) facing down on a
cushioned table or flat surface to protect the
screen(or back) from scratches.
yy
Make sure that the screws are inserted correctly and fastened securely. (If they are not
fastened securely enough, the TV may tilt
forward after being installed.)
Do not use too much force and over tighten
the screws; otherwise screw may be damaged and not tighten correctly.
CAUTION
yyWhen detaching the stand, make sure to hold it
firmly while removing the screws to stop it from
falling.
yyWhen you assemble the stand again, have the
arrows on the bottom of the stand base looking
toward same direction to screen.
NOTE
yy
When you assemble the stand again,
performing the stand detaching in reverse.
20 ASSEMBLING AND PREPARING
ENG
ENGLISH
Assembling the AV cover
Mounting on a table
Assemble the AV Cover as shown.
1 Lift and tilt the TV into its upright position on a
table.
-Leave a 10 cm (minimum) space from the wall
for proper ventilation.
(Only EC93**)
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
10 cm
AV cover
(Only EC97**)
5 cm
10 cm
AV cover
2 Connect the power cord to a wall outlet.
(Only EC98**)
CAUTION
yyDo not place the TV near or on sources of
heat, as this may result in fire or other damage.
AV cover
ASSEMBLING AND PREPARING 21
(This feature is not available for all models.)
To use the desk-type stand safely, make sure to
securely attach it to a wall.
Mounting on a wall
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the floor.
When you attach the TV to other building materials, please contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
We recommend the use of LG’s wall mount bracket.
When you do not use LG’s wall mount bracket,
please use a wall mount bracket where the device
is adequately secured to the wall with enough
space to allow connectivity to external devices.
10 cm
10 cm
10 cm
10 cm
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
Make sure to use screws and wall mount bracket
that meet the VESA standard. Standard dimensions for the wall mount kits are described in the
following table.
Separate purchase(Wall Mounting Bracket)
Model
55EC93**
65EC97**
210
210
M6
2
OSW100
M6
2
OSW200
(A)
A
CAUTION
yy Make sure that children do not climb on or
hang on the TV.
NOTE
yy Use a platform or cabinet that is strong and
large enough to support the TV securely.
yy Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
Standard screw
Number of screws
Wall mount
bracket
ENGLISH
ENG
Securing the TV to a wall
22 ASSEMBLING AND PREPARING
ENG
ENGLISH
Model
77EC98**
VESA (A x B)
A
B
Wall Type Set-up Guide
(Only EC98** - Seperate purchase)
400 x 400
Guide spacer assembly
1 Remove the VESA screws (4EA).
Standard screw
Number of screws
M6
4
LSW420BX
Wall mount
bracket
CAUTION
yy Disconnect the power first, and then move
or install the TV. Otherwise electric shock
may occur.
yy If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and
contact the local dealer or qualified
personnel.
yy Do not over tighten the screws as this may
cause damage to the TV and void your
warranty.
yy Use the screws and wall mounts that
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
VESA screw
2 Assemble Guide spacer (4EA) and Guide
spacer screws (4EA).
NOTE
yy Use the screws that are listed on the VESA
standard screw specifications.
yy The wall mount kit includes an installation
manual and necessary parts.
yy The wall mount bracket is not provided. You
can obtain additional accessories from your
local dealer.
yy The length of screws may differ depending
on the wall mount. Make sure to use the
proper length.
yy For more information, refer to the manual
supplied with the wall mount.
Guide
spacer
screw
Guide spacer
Wall mount bracket installation
1 After installation, move the bracket forward.
ASSEMBLING AND PREPARING 23
Type 1. Hanging the TV on the wall before
removing a stand.
Type 2. Hanging the TV on the wall after removing a
stand.
1
1
Wall mount
bracket
2
CAUTION
yy When laying the TV on its back on a padded
table or surface, be careful to prevent the
TV from being damaged.
2
3
4
3
Stand
5
Stand
ENGLISH
ENG
How to detach the stand
24 ASSEMBLING AND PREPARING
ENG
ENGLISH
Tidying cables
4
Image shown may differ from your TV.
** Stand Type **
(Only EC93**)
Gather and bind the cables with the cable holder.
Wall mount
bracket
5
Cable Holder
(Only EC97**)
1 Put the cable management in the hole of TV
back cover.
6
Cable
Management
2 EA
ASSEMBLING AND PREPARING 25
(Only EC98**)
Gather and bind the cables with the cable holder.
Cable Holder
M4 x L10
2 EA
3 Gather and bind the cables with the cable holder.
Arrange the cable in the cable mangement.
** Wall Mount Type **
(Only EC93**)
Cable Holder
Cable Management
Cable Holder
CAUTION
yy Do not move the TV by holding the cable
holder, as the cable holder may break, and
injuries and damage to the TV may occur.
ENGLISH
ENG
2 Fix the cable management with cable management
Screw.
26 ASSEMBLING AND PREPARING
ENG
ENGLISH
Using Built-in Camera
(Only EC97**, EC98**)
Preparing Built-in Camera
1 Pull up the built-in camera at the back of the TV.
Angle Adjustment
Lever
Slide
NOTE
yyBefore using the built-in camera, you must
recognize the fact that you are legally
responsible for the use or misuse of the
camera by the relevant national laws including
the criminal law.
yyThe relevant laws include the Personal
Information Protection law which regulates
the processing and transferring of personal
information and the law which regulates the
monitoring by camera in a workplace and
other places.
yyWhen using the built-in camera, avoid
questionable, illegal, or immoral situations.
Other than at public places or events, consent
to be photographed may be required. We
suggest avoiding the following situations :
(1) Using the camera in areas where the use
of camera is generally prohibited such as
restroom, locker room, fitting room and security
area.
(2) Using the camera while causing the
infringement of privacy.
(3) Using the camera while causing the
violation of the relevant regulations or laws.
NOTE
Remove the protective film before using the
yy
built-in camera.
2 You can adjust the angle of the camera with
the angle adjustment lever on the back on the
back of the built-in camera.
[Side View]
7
5
Lever
7
5
Lens
ASSEMBLING AND PREPARING 27
Name of Parts of Built-in
camera
Camera Lens
Protective
Film
Microphone
Checking the Camera’s
Shooting Range
1 Press the
(Home) button on the remote
control to display the HOME menu.
2 Select CAMERA and then press the
Wheel(OK) button.
NOTE
The optimal distance from the camera to use
yy
the motion recgnition function is between 1.5
m and 4.5 m.
ENGLISH
ENG
3 Push down the built-in camera when you are
not using it.
28
MAKING CONNECTIONS
ENG
ENGLISH
MAKING
CONNECTIONS
Antenna Connection
This section on MAKING CONNECTIONS mainly
uses diagrams for the EC93** models.
Connect various external devices to the TV and
switch input modes to select an external device. For
more information on external device’s connection,
refer to the manual provided with each device.
Available external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.
NOTE
The external device connection may differ
yy
from the model.
Connect external devices to the TV
yy
regardless of the order of the TV port.
If you record a TV program on a DVD
yy
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
of recording, refer to the manual provided
with the connected device.
Refer to the external equipment’s manual
yy
for operating instructions.
If you connect a gaming device to the TV,
yy
use the cable supplied with the gaming
device.
In PC mode, there may be noise associated
yy
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE
menu until the picture is clear.
In PC mode, some resolution settings may
yy
not work properly depending on the graphics
card.
If Ultra HD content is played via PC, the video
yy
or audio may have disruptions intermittently
depending on your PC’s performance.
Wall Antenna
Socket
13/18V
700mA Max
LNB IN
Satellite
IN
ANTENNA/
CABLE
(*Not
Provided)
Connect the TV to a wall antenna socket with an RF
cable (75 Ω).
NOTE
Use a signal splitter to use more than 2 TVs.
yy
If the image quality is poor, install a signal
yy
amplifier properly to improve the image
quality.
If the image quality is poor with an antenna
yy
connected, try to realign the antenna in the
correct direction.
An antenna cable and converter are not
yy
provided.
Supported DTV Audio: MPEG, Dolby Digital,
yy
Dolby Digital Plus, HE-AAC
MAKING CONNECTIONS
(Only EC97**)
ENGLISH
ENG
Satellite dish Connection
29
(Only satellite models)
Satellite
Dish
(*Not
Provided)
13/18V
700mA Max
LNB IN
Satellite
IN
ANTENNA/
CABLE
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
HDMI Connection
HDMI
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
(Only EC93**)
(4K@60Hz)
(4K@60Hz)
(Only EC98**)
(*Not
Provided)
HDMI
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
HDMI
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
30
MAKING CONNECTIONS
ENG
ENGLISH
Transmits the digital video and audio signals from
an external device to the TV. Connect the external
device and the TV with the HDMI cable as shown.
ARC (Audio Return Channel)
An external audio device that supports
yy
SIMPLINK and ARC must be connected
using HDMI/DVI IN 1 (ARC) or HDMI(4K @
60 Hz)/DVI IN 2 (ARC) port.
When connected with a high-speed
yy
HDMI cable, the external audio device
that supports ARC outputs optical SPDIF
without additional optical audio cable and
supports the SIMPLINK function.
DVI to HDMI Connection
(Only EC93**)
AV2
IN
( Audio in)
NOTE
It is recommended to use the TV with the
yy
HDMI connection for the best image quality.
Use the latest High Speed HDMI™ Cable with
yy
CEC (Customer Electronics Control) function.
High Speed HDMI™ Cables are tested to
yy
carry an HD signal up to 1080p and higher.
yySupported HDMI Audio format : Dolby Digital
(32Khz, 44.1Khz, 48Khz), DTS(44.1Khz, 48Khz),
PCM (32Khz, 44.1Khz, 48Khz, 96Khz, 192Khz)
(Only EC97**, EC98**)
1) HDMI specifications may be different for each
input port, so make sure to check the device
specifications before connecting.
(*Not
Provided)
AUDIO OUT
DVI OUT
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
(Only EC97**)
2) Contact customer service for more information
on the HDMI specifications of each input port.
4K @ 50/60 Hz Support Format
Colour Depth /
Frame
Resolution
Chroma Sampling
rate (Hz)
8 bit 10 bit 12 bit
YCbCr
YCbCr 4:2:0 1
4:2:0
50.00
YCbCr 4:2:2 1
3840 x 2160p
YCbCr
59.94
4096 x 2160p
4:4:4 1
60.00
RGB
4:4:4 1
1: Only Supported at HDMI IN 3 Port
NOTE
AV2
IN
( Audio in)
(*Not Provided)
When you use HDMI port 3, it is recommendyy
ed that you use the cable provided. If you
want to use a regular HDMI cable, use one
that is a highspeed HDMI cable (3m or less).
AUDIO OUT
DVI OUT
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
E
MAKING CONNECTIONS
(4K@60Hz)
AV2
2
CO
( Audio in))
(4K@60Hz)
(Only EC93**)
(*Not
Provided)
AUDIO OUT
MHL passive
cable
(*Not Provided)
DVI OUT
DVD / Blu-Ray / PC /
HD Cable Box / HD STB
Transmits the digital video signal from an external
device to the TV. Connect the external device and
the TV with the DVI-HDMI cable as shown. To
transmit an audio signal, connect an audio cable.
NOTE
Depending on the graphics card, DOS mode
yy
may not work if a HDMI to DVI Cable is in
use.
When using the HDMI / DVI cable, Single
yy
link is only supported.
Mobile phone
(Only EC97**, EC98**)
MHL passive
cable
(*Not Provided)
Mobile phone
ENGLISH
ENG
MHL Connection
(Only EC98**)
31
32
MAKING CONNECTIONS
ENG
ENGLISH
Mobile High-definition Link (MHL) is an interface
for transmitting digital audiovisual signals from
mobile phones to television sets.
Component Connection
NOTE
yyConnect the mobile phone to the HDMI/DVI IN
4 (MHL) or HDMI(4K @ 60 Hz)/DVI IN 4 (MHL)
port to view the phone screen on the TV.
The MHL passive cable is needed to
yy
connect the TV and a mobile phone.
This only works for the MHL-enabled phone.
yy
Some applications can be operated by the
yy
remote control.
yyFor some mobile phones supporting MHL,
you can control with the magic remote control.
Remove the MHL passive cable from the TV
yy
when:
--The MHL function is disabled
--Your mobile device is fully charged in
standby mode
IN
COMPONENT
AV2
VIDEO
AUDIO
AV2
PR
PB
Y
IN
( Audio in)
YELLOW
(Use the
composite gender
cable provided.)
GREEN
(Use the
component gender
cable provided.)
BLUE
RED
BLUE
RED
RED
GREEN GREEN
RED
WHITE WHITE
YELLOW
(*Not Provided)
RED
BLUE
GREEN
RED
WHITE
L
R
AUDIO
VIDEO
DVD / Blu-Ray / HD Cable Box
Transmits analogue video and audio signals from an
external device to the TV. Connect the external device
and the TV with a component gender cable as shown.
NOTE
yy
If cables are not installed correctly, it could
cause this image to display in black and
white or with distorted colours.
MAKING CONNECTIONS
IN
AV2
VIDEO
Headphone Connection
COMPONENT
AUDIO
PR
PB
Y
OUT
Ext.Speaker
/ H/P
AV2
IN
( Audio in)
YELLOW
(Use the composite
gender cable provided.)
WHITE
RED
WHITE
RED
YELLOW YELLOW
(*Not Provided)
RED
WHITE
YELLOW
VIDEO
L (MONO) AUDIO R
DVD / Blu-Ray / HD Cable Box / VCR
Transmits analogue video and audio signals from
an external device to the TV. Connect the external
device and the TV with a composite gender cable
as shown.
(*Not Provided)
Transmits the headphone signal from the TV to
an external device. Connect the external device
and the TV with the headphone as shown.
NOTE
yy
AUDIO menu items are disabled when connecting a headphone.
yy
Optical Digital Audio Out is not available
when connecting a headphone.
yy
Headphone impedance: 16 Ω
yy
Max audio output of headphone: 0.627 mW
to 1.334 mW
yy
Headphone jack size: 0.35 cm
ENGLISH
ENG
Composite Connection
33
34
MAKING CONNECTIONS
USB Connection
2
3
(Only EC93**)
USB
OUT
1
OPTICAL
DIGITAL
AUDIO
(*Not
Provided)
OPTICAL AUDIO IN
Digital Audio System
You may use an external audio system instead of
the built-in speaker.
HDD
USB
HUB
(*Not Provided) (*Not Provided) (*Not Provided)
(Only EC97**, EC98**)
3
Digital optical audio connection
USB
2
Transmits a digital audio signal from the TV to an
external device. Connect the external device and
the TV with the optical audio cable as shown.
CAUTION
1
yy
Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
yy
Audio with ACP (Audio Copy Protection)
function may block digital audio output.
HDD
ENG
ENGLISH
Audio Connection
USB
(*Not
Provided)
HUB
(*Not
Provided)
HDD
(*Not Provided)
MAKING CONNECTIONS
CI module Connection
PCMCIA CARD SLOT
NOTE
(*Not Provided)
PCMCIA CARD SLOT
Some USB Hubs may not work. If a USB
yy
device connected using a USB Hub is not
detected, connect it to the USB IN port on
the TV directly.
Connect the external power source if your
yy
USB is needed.
Connecting via USB 3.0:
yy
Some USB device may not work if it dose not
meet USB 3.0 standard. In case, connect it
to USB IN 2 or USB IN 3 port. (Only EC97**,
EC98**)
View the encrypted (pay) services in digital TV
mode. This feature is not available in all countries.
NOTE
Check if the CI module is inserted into the
yy
PCMCIA CARD SLOT in the right direction.
If the module is not inserted properly, this
can cause damage to the TV and the
PCMCIA CARD SLOT.
If the TV does not display any video and
yy
audio when CI+ CAM is connected, please
contact to the Antenna/Cable/Satellite Service Operator.
ENGLISH
ENG
Connect a USB storage device such as a USB
flash memory, external hard drive or a USB
memory card reader to the TV and access the
Smart Share menu to use various multimedia files.
35
36
MAKING CONNECTIONS
ENG
ENGLISH
Euro Scart Connection
NOTE
Any Euro scart cable used must be signal
yy
shielded.
When watching digital TV in 3D imaging
yy
mode, only 2D out signals cannot be output
through the SCART cable.
If you use the Time Machine function on
yy
digital TV, TV out signals cannot be output
through the SCART cable.
IN/OUT
(RGB)
AV 1
(Use the Scart gender
cable provided.)
(*Not
Provided)
AUDIO / VIDEO
Transmits the video and audio signals from an
external device to the TV set. Connect the external
device and the TV set with the Scart gender cable
as shown.
Output
Type
AV1
Current
(TV Out1)
input mode
Digital TV
Digital TV
Analogue TV, AV
Component
Analogue TV
HDMI
1 TV Out : Outputs Analogue TV or Digital TV
signals.
REMOTE CONTROL 37
(Depending on model)
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching
the
and
ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
ENGLISH
ENG
REMOTE CONTROL
or
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
yy The remote control will not be included for all sales market.
Make sure to point the remote control toward the remote control sensor on the TV.
(POWER) Turns the TV on or off.
INPUT Changes the input source.
SETTINGS Accesses the main menus.
Q. MENU Accesses the quick menus.
INFO Views the information of the current programme and screen.
SUBTITLE Recalls your preferred subtitle in digital mode.
TV/RAD
Selects Radio, TV and DTV programme.
Number buttons Enters numbers.
(Space) Opens an empty space on the screen keyboard.
GUIDE Shows programme guide.
Q.VIEW Returns to the previously viewed programme.
Adjusts the volume level.
FAV Accesses your favourite programme list.
Used for viewing 3D video.
MUTE
Mutes all sounds.
P
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
FAV
P
PAGE
1
1
RECENT Shows the previous history.
SMART Accesses the Home menus.
LIVE MENU Shows the list of Recommended, Programmes, Search
and Recorded.
1 Teletext buttons(
TEXT / T.OPT) These buttons are used for teletext.
OK
Selects menus or options and confirms your input.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
BACK Returns to the previous level.
EXIT Clears all on-screen displays and returns to TV viewing.
2
AD By Pressing AD button, audio descriptions function will be enabled.
REC/
Starts to record and displays record menu. (only Time MachineReady
support model)
Control buttons (
) Controls the Premium contents, Time
MachineReady or SmartShare menus or the SIMPLINK compatible devices
(USB or SIMPLINK or Time MachineReady).
2 Coloured buttons These access special functions in some menus.
( : Red,
: Green,
: Yellow,
: Blue)
38 REMOTE CONTROL
ENG
ENGLISH
(POWER) Turns the TV on or off.
INPUT Changes the input source.
SETTINGS Accesses the main menus.
Q. MENU Accesses the quick menus.
INFO Views the information of the current programme and screen.
(User Guide) Sees user-guide.
•
Number buttons Enters numbers.
(Space) Opens an empty space on the screen keyboard.
GUIDE Shows programme guide.
Q.VIEW Returns to the previously viewed programme.
FAV
P
P
A
G
E
Adjusts the volume level.
FAV Accesses your favourite programme list.
Used for viewing 3D video.
MUTE Mutes all sounds.
P Scrolls through the saved programmes.
PAGE Moves to the previous or next screen.
RECENT Shows the previous history.
SMART Accesses the Home menus.
MY APPS Shows the list of Apps.
Navigation buttons (up/down/left/right) Scrolls through menus or options.
OK
Selects menus or options and confirms your input.
BACK Returns to the previous level.
LIVE MENU Shows the list of Recommended, Programmes, Search
and Recorded.
EXIT Clears all on-screen displays and returns to TV viewing.
SUBTITLE
1
Time Machine
Coloured buttons These access special functions in some menus.
( : Red,
: Green,
: Yellow,
: Blue)
1
Teletext buttons(
TEXT / T.OPT) These buttons are used for teletext.
APP/ Selects the MHP TV menu source. (Only Italy.) (Depending on model)
Control buttons (
) Controls the Premium contents, Time
MachineReady or SmartShare menus or the SIMPLINK compatible devices
(USB or SIMPLINK or Time MachineReady).
LIVE TV Returns to LIVE TV.
REC/
Starts to record and displays record menu. (only Time MachineReady
support model)
SUBTITLE Recalls your preferred subtitle in digital mode.
AD By Pressing AD button, audio descriptions function will be enabled.
TV/RAD Selects Radio, TV and DTV programme.
MAGIC REMOTE FUNCTIONS 39
When the message “Magic Remote battery is low. Change the battery.” is displayed,
replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching
and ends to the label inside the compartment, and close the battery cover. Be sure to
point the remote control toward the remote control sensor on the TV.
To remove the batteries, perform the installation actions in reverse.
CAUTION
yy
Do not mix old and new batteries, as this may damage the remote control.
(BACK)
Returns to the previous screen.
(POWER)
Turns the TV on or off.
Navigation buttons (up/down/left/right)
Press the up, down, left or right button to scroll the menu. If you press
buttons while the pointer
is in use, the pointer will disappear
from the screen and Magic Remote
will operate like a general remote
control. To display the pointer on the
screen again, shake Magic Remote
to the left and right.
BACK
HOME
Wheel(OK)
Press the center of the Wheel button
to select a menu.
You can change programmes by
using the wheel button.
P
MY APPS
Coloured buttons
These access special functions in
some menus.
( : Red
: Green
: Yellow
: Blue)
Adjusts the volume level.
(Home)
Accesses the Home menu.
(EXIT to LIVE)
Switches among broadcast (antenna) and various inputs.
(Voice recognition)
P
Scrolls through the saved programmes.
/INPUT
1
Displays the Screen Remote.
* Accesses the Universal Control Menu.
(Depending on model)
* Pressing and holding the
button
will display a menu to select an external
device that is connected to the TV.
1
(Depending on model)
Used for viewing 3D video.
1
(Depending on model)
Press the
button for a second to use
the eGallery service that you can enjoy the
famous paintings and iconic photographs.
(MUTE)
Mutes all sounds.
*By Pressing and holding the
button, audio descriptions function will
be enabled.
ENGLISH
ENG
MAGIC REMOTE FUNCTIONS
40 MAGIC REMOTE FUNCTIONS
ENG
ENGLISH
Voice recognition
Network connection is required to use the voice
recognition function.
1.Press the Voice recognition button.
2.Speak when the voice display window appears on the left of the TV screen.
• The voice recognition may fail when you
speak too fast or too slow.
• Use the Magic remote control no further
than 10 cm from your face.
• The recognition rate may vary depending
on the user’s characteristics (voice,
pronunciation, intonation and speed) and
the environment (noise and TV volume).
Registering Magic Remote
How
the Magic Remote
BACKto register
HOME
(Wheel)
P
MY APPS
To use the Magic Remote, first
pair it with your TV.
1 Put batteries into the Magic
Remote and turn the TV on.
2 Point the Magic Remote at
your TV and press the
Wheel (OK) on the remote
control.
* If the TV fails to register the
Magic Remote, try again after
turning the TV off and back on.
How to deregister the Magic Remote
(BACK)
(Home)
Press the
(BACK) and
(Home) buttons at the same
time, for five seconds, to unpair
the Magic Remote with your TV.
* Pressing and holding the
(EXIT to LIVE) button will let
you cancel and re-register
Magic Remote at once.
How to use magic remote
yyShake the Magic Remote
slightly to the right and left or
press
(Home),
,
buttons to make the pointer
appear on the screen.
(In some TV models, the
pointer will appear when you
turn the Wheel button.)
yyIf the pointer has not been
used for a certain period
of time or Magic Remote is
placed on a flat surface, then
the pointer will disappear.
yy If the pointer is not
responding smoothly, you can
reset the pointer by moving it
to the edge of the screen.
yy The Magic Remote depletes
batteries faster than a normal
remote due to the additional
features.
MAGIC REMOTE FUNCTIONS / USING THE USER GUIDE 41
User Guide allows you to more easily access the
detailed TV information.
1 Press the
(Home) button to access the Home menu.
2 Select User Guide and press the
button.
Wheel(OK)

Use the Magic Remote within the maximum
yy
communication distance (10 m). Using the
Magic Remote beyond this distance, or
with an object obstructing it, may cause a
communication failure.
A communication failure may occur due to
yy
nearby devices. Electrical devices such as
a microwave oven or wireless LAN product
may cause interference, as these use the
same bandwidth (2.4 GHz) as the Magic
Remote.
The Magic Remote may be damaged or may
yy
malfunction if it is dropped or receives a
heavy impact.
Take care not to bump into nearby furniture
yy
or other people when using the Magic
Remote.
Manufacturer and installer cannot provide
yy
service related to human safety as the
applicable wireless device has possibility of
electric wave interference.
It is recommended that an Access Point (AP)
yy
be located more than 1 m away from the
TV. If the AP is installed closer than 1 m, the
Magic Remote may not perform as expected
due to frequency interference.
USING THE USER
GUIDE
NOTE
You can also access the User Guide by pressyy
ing (User Guide) in the remote control.
(Depending on model)
ENGLISH
ENG
Precautions to Take when
Using the Magic Remote
42 MAINTENANCE
ENG
ENGLISH
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall
outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in
scratches and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING 43
Problem
ENGLISH
ENG
TROUBLESHOOTING
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
yy Check if the batteries are still working and properly installed (
to ,
to
No image display
and no sound is
produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Automatic Standby (Depending on model) / Sleep Timer / Timer
Power off feature is activated in the TIMERS settings.
yy If there is no signal while the TV is on, the TV will turn off automatically after 15
minutes of inactivity.
When connecting
to the PC (HDMI/
DVI), ‘No signal’ or
‘Invalid Format’ is
displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the HDMI cable.
yy Restart the PC with the TV on.
).
44 SPECIFICATIONS
ENG
ENGLISH
SPECIFICATIONS
(Only EC93**)
Wireless module(LGSBW41)Specifications
Wireless LAN
Standard
IEEE 802.11a/b/g/n
Frequency Range
Bluetooth
Standard
Bluetooth Version 3.0
2400 to 2483.5MHz
5150 to 5250 MHz
Frequency Range
5725 to 5850 MHz(for Non EU)
Output Power (Max.)
802.11a: 13 dBm
802.11b: 15 dBm
802.11g: 14 dBm
802.11n - 2.4GHz: 16 dBm
802.11n - 5GHz: 16 dBm
2400 to 2483.5MHz
Output Power (Max.)
10dBm or Lower
yy
Because band channel used by the country could be different, the user can not change or adjust the
operating frequency and this product is set for the regional frequency table.
yy
This device should be installed and operated with minimum distance 20 cm between the device and your
body. And this phrase is for the general statement for consideration of user environment.
0197
(Only EC97**, EC98**)
Wireless module(LGSWF41)Specifications
Standard
0197
Frequency Range
Output Power (Max.)
IEEE 802.11a/b/g/n/ac
2400 to 2483.5MHz
5150 to 5250 MHz
5725 to 5850 MHz(for Non EU)
802.11a: 14.5 dBm
802.11b: 16 dBm
802.11g: 13.5 dBm
802.11n - 2.4GHz: 14 dBm
802.11n - 5GHz: 15.5 dBm
802.11ac - 5GHz : 16 dBm
Bluetooth module(BM-LDS401)Specifications
Standard
Bluetooth Version 3.0
Frequency Range
Output Power (Max.)
2400 ~ 2483.5 MHz
10 dBm or lower
yy
Because band channel used by the country could be different, the user can not change or adjust the
operating frequency and this product is set for the regional frequency table.
yy
This device should be installed and operated with minimum distance 20 cm between the device and your
body. And this phrase is for the general statement for consideration of user environment.
0197
0197
SPECIFICATIONS 45
55EC93**
MODEL
Dimensions
(W x H x D)
55EC930V-ZA
With stand (mm)
1225 x 753 x 204
Without stand (mm)
1225 x 715 x 44
With stand (kg)
Weight
16.7
Without stand (kg)
14.7
Power consumption
320 W
Power requirement
AC 100-240 V~ 50 / 60 Hz
65EC97**
MODEL
Dimensions
(W x H x D)
Weight
65EC970V-ZA
With stand (mm)
1447.4 x 880.1 x 256.6
Without stand (mm)
1447.4 x 826.9 x 56.3
With stand (kg)
25.5
Without stand (kg)
24.1
Power requirement
AC 100-240 V~ 50 / 60 Hz
77EC98**
MODEL
Dimensions
(W x H x D)
Weight
77EC980V-ZA
With stand (mm)
1718 x 1110 x 322
Without stand (mm)
1718 x 1064 x 34.7
With stand (kg)
43.3
Without stand (kg)
39.9
Power requirement
AC 100-240 V~ 50 / 60 Hz
CI Module Size (W x H x D)
100.0 mm x 55.0 mm x 5.0 mm
Operating Temperature
Environment condition
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Television system
Programme coverage
Maximum number of storable programmes
External antenna impedance
Digital TV
Analogue TV
DVB-T/T2
DVB-C
DVB-S/S2
VHF, UHF
C-Band, Ku-Band
PAL/SECAM B/G/I/D/K
SECAM L/L’
VHF: E2 to E12,
UHF : E21 to E69,
CATV: S1 to S20,
HYPER: S21 to S47
DVB-S/S2 : 6,000
DVB-T/T2/C & Analogue TV : 1,500
75 Ω
ENGLISH
ENG
Product specifications may be changed without prior notice due to upgrade of product functions.
Please contact LG First.
If you have any inquiries or comments,
please contact LG customer information centre.
Customer Information Centre
Country
Service
Country
0 810 144 131
0900 543 5454
015 200 255
800 187 40
0032 15 200 255
801 54 54 54
07001 54 54
808 78 54 54
810 555 810
031 228 3542
8088 5758
0850 111 154
0800 0 54 54
Record the model number and serial
number of the TV.
Refer to the label on the back cover and
quote this information to your dealer when
requiring any service.
SERIAL
Latvija
963 649 270
54
0770 54 54 54
01806 11 54 11
(0,20€ pro Anruf
aus dem Festnetz
der DTAG; Mobilfunk: max. 0,60€
pro Anruf)
0848 543 543
3220
MODEL
Service
801 11 200 900,
210 4800 564
0344 847 5454
06 40 54 54 54
800 9990
01 686 9454
0 800 303 000
199600099
8 820 0071 1111
8 8000 805 805,
2255(GSM)
80200201
8 800 120 2222
880008081
8 0000 710 005
8 800 200 7676
Download PDF