LG | MW-30LZ10 | LG MW-30LZ10 Owner’s Manual

Please read this manual
ating
carefully
before oper-
your set.
Retain it for future reference.
Record model number and serial number of
the set.
See the label attached
on
the back of the set
and quote this information to your dealer when
you require service.
Model number
:
Serial number
:
LCDMONITR
MW-30LZ10
OWNER'S MANUAL
Multimedia
Display
This LCD monitor
The LCD
The
panel
be connected to
a
PC in
place
of the PC Monitor.
Display panel
is
composed
coloured dots
on
cells has been
exchange
can
the
of 2.9 million individual cells and
screen as a
adopted by
all
few defective cells
are likely to appear as
process. This tolerance of upto six defective
manufacturers and therefore would not be considered as reason for
result of the
panel
a
manufacturing
refund.
or
FCC NOTICE
?
A Class B
This
digital
equipment
device
has been tested and found to
to Part 15 of the FCC Rules. These limits
interference in
a
comply with the limits for a Class B digital device, pursuant
designed to provide reasonable protection against harmful
equipment generates, uses and can radiate radio frequency
are
residential installation. This
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
-
-
-
?
Connect the
equipment
Consult the dealer
into
outlet
an
on a
circuit different from that to which the receiver is connected.
experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible
could void the user's authority to operate the equipment.
-
or an
for
compliance
Warning
This is
a
class B
ence, in which
product.
case
the
In
a
user
domestic environment this
may be
required
to take
product may cause
adequate measures.
radio interfer-
Table of Contents
First step
Safety instructions ....................................................4
Monitor Overview
Front Panel Controls ..............................................12
Connection Panel Overview ...................................13
Remote Control Key Functions ..............................14
Accesories/Optinal extra.........................................16
Using the remote control ........................................17
Equipment Connections and Setup
VCR Setup..............................................................18
Cable TV Setup ......................................................20
External AV Source Setup ......................................21
DVD
Setup..............................................................22
Setup ..............................................................23
Connecting to a wireless transmitter(option) ..........24
Connecting to a wireless receiver(option) ..............25
PC Setup ................................................................26
DTV
Basic Features Setup and Operation
Turning on the Monitor ...........................................29
Checking features...................................................30
Sleep Timer
Setting Sleep
Timer ................................................31
Picture & Sound
Auto picture control ................................................32
Adjusting picture appearance .................................33
Auto Sound Control ................................................34
Adjusting Sound: Bass, Treble, Balance ................35
Special Features
Selecting language for the menus..........................36
Adjusting color temperature ...................................37
Using the screen saver function .............................38
Setting picture format .............................................39
Using the Zoom in/out function ..............................40
Moving the picture ..................................................41
Picture In Picture(PIP) function ..............................42
Zoom in/out main picture ........................................44
Twin picture function...............................................45
Using the screen options ........................................47
PC Mode feature check..........................................48
PC Mode adjustment ..............................................49
External control device setup .................................51
Others
check list ......................................59
Note ........................................................................61
Product specifications.............................................63
Troubleshooting
Safety
Instructions
WARNING
Indorstali
NOTES
Do not place the Monitor in
direct sunlight or near heat
sources such as radiators, fires
and stove etc.
This may
-
cause a
Do not place inflammable materials beside the monitor
-
This may
cause a
fire hazard !
fire hazard !
NOTES
Indorstali
Do not place the monitor where
it might be exposed to dust.
When unpacking or moving
the Monitor two people will be
necessary to lift it safely.
-
This may
cause a
fire hazard !
NOTES
Indorstali
4
Ensure good ventilation around
the monitor. The distance
between the monitor and the
wall should be more than 10cm.
-
It make internal
temperature increase
and
causes a
fire.
Do not cover the vent
the monitor.
-
This may
cause a
grilles
fire hazard !
of
*
Safety
instructions have two kinds of information
WARNING
NOTES
as
illustrated below.
The violation of this instruction may
cause
serious
The violation of this instruction may
cause
light injuries
injuries
or
and
even
damage
death.
of the
product.
Take
care
of
danger that may happen
under
NOTES
specific condition.
Do not
the monitor close to
of steam or oil such as a
humidifier.
place
sources
Disconnect from the mains
and remove all connections
before moving.
This may create a fire hazard
electric shock hazard !
-
or an
NOTES
When installing the monitor on a table, be
careful not to place it near the edge.
This may
-
injury
to
cause
a
child
monitor.
Surely
-
use a
use the monitor on
level and stable surface.
Only
the monitor to fall causing serious
adult and serious damage to the
-
It may fall down
or
be
a
upset.
or
fitting table
or
rack.
NOTES
Do not place the monitor directly
where ventilation is restricted.
-
This would cause its internal
create a fire hazard !
on a
temperature
carpet, rug
to increase and
or
place
might
SafetyinsrucoMOvwCBplmP&d
Others
5
Safety
Instructions
WARNING
Do not use the Monitor in a
where it is likely to get wet.
-
OutdorInsali
This may
cause a
fire
or an
such
damp place
as a
bathroom
electric shock hazard !
WARNING
OutdorInsali
In case of using a receiver (VCR,
Digital Set Top Box), do not place an
antenna in the vicinity of power lines.
This may
-
cause an
electric shock.
In case of using a receiver
(VCR, Digital Set Top Box),
contact your service center to
construct an antenna because
it needs skilled
-
This may
man.
cause an
electric shock.
WARNING
Earth wire should be connected.
-
-
Power
6
-
If the earth wire is not connected,
there is possible a danger of electric
shock caused by the current leakage.
If grounding methods are not possible, a separate circuit breaker should
be employed and installed by a qualified electrician.
Do not connect ground to telephone
wires, lightning rods or gas pipe.
The mains plug should be
inserted fully into the
power outlet to avoid a fire
hazard !
-
This may
cause a
fire hazard !
WARNING
In case of using a receiver (VCR,
cable between inside and outside
-
This may
cause
water
damaged
Digital Set Top Box), Bend antenna
building to prevent rain from flowing
inside the Monitor and could
give
an
in.
electric shock.
NOTES
of using a receiver (VCR, Digital Set Top Box), there should be
distance between an outside antenna and power lines to keep
the former from touching the latter even when the antenna falls.
In
case
enough
-
This may
cause an
electric shock.
NOTES
Do not place heavy
the power cord
objects
on
-
This may cause
shock hazard !
a
fire
or an
electric
Do not use too many plugs
the Mains multi-outlet.
-
on
It may result in overheating of the
outlet and causes a fire hazard !
Never touch the power
with a wet hand
-
This may
hazard !
cause an
plug
electric shock
SafetyinsrucoMOvwCBplmP&d
Others
7
Safety
Instructions
NOTES
Hold the plug firmly when
unplugging. If you pull the
cord the cord may be dam-
Prevent dust
power
-
aged.
Power
This may
-
cause a
collecting on
plug pins or outlet.
This may
cause a
the
fire hazard !
fire hazard !
WARNING
Do not place
monitor such
This may
-
anything containing liquid on top of the
as flowerpot, cup, cosmetics or candle.
cause a
fire hazard !
Using
WARNING
If water is spilt into the monitor
unplug it from the mains supply outlet immediately and consult your
Service Agent.
-
Using
8
This may
cause an
electric shock hazard !
Dispose of used batteries
carefully and safely.
-
In the case of a battery being
swallowed by a child please consult a doctor immediately.
NOTES
Do not plug when the power cord or the plug is
damaged or the connecting part of the power
outlet is loose.
-
This may
cause a
fire
or an
electric shock hazard !
Ensure the power cord does not come
into contact with sharp or hot objects such
as a heater.
-
This may
cause a
fire
or an
electric shock hazard !
NOTES
In case of impact shock or damage to the monitor
switch it off and unplug it from the outlet and contact
your service center.
Do not allow any
monitor.
-
This may
-
cause a
fire
or an
electric shock hazard !
This may
cause an
objects
to fall into the
electric shock hazard !
NOTES
Do not
-
drop
This may
the monitor
cause
or
allow
mechanical failure
or
impact
injury
shock.
!
SafetyinsrucoMOvwCBplmP&d
Others
9
Safety
Instructions
WARNING
In the event that an image does not appear on the screen please
switch it off and unplug it from the mains suuply and contact your
Service Centre.
-
This may
cause a
fire
or an
electric shock hazard !
Using
WARNING
Do not
-
Cleanig
water while
the Monitor
use
cleaning
This may cause damaged the
Monitor or an electric shock hazard.
In the
unlikely
event
of smoke
strange smell from the
Monitor, switch it off ,unplug it
or a
from the wall outlet and contact
your dealer or service centre.
-
This may cause
shock hazard !
a
fire
or an
electric
WARNING
Do not attempt to service
the Monitor yourself.
Contact your dealer or service centre.
-
Others
10
This may cause damage to the
Monitor and could give an electric Shock as well as invalidating
the warranty !
In the event of a lightning or
thunder storm unplug the
Monitor and aerial from the
wall outlet.
-
This will prevent damage to the
Monitor and possible electric shock.
WARNING
NOTES
Do not watch the monitor while
driving
Do not place heavy
the Monitor.
or
-
This may
cause an
objects
on
walking.
accident.
-
This may cause serious
a child or adult.
injury
to
NOTES
from the wall outlet
not use liquid cleanaerosol cleaners.
Unplug
before
ers or
-
this product
cleaning. Do
This may cause damage to the Monitor
an electric shock hazard !
Contact the service center once
the internal part of the monitor.
-
-
Accumulated dust
can cause
a
year to clean
mechanical failure.
or cause
NOTES
The distance between eyes
and the screen should be
about 1.5m.
-
If not, eyes will strain.
Unplug the Monitor from the
wall outlet when it is left
unattended and unused for
long periods of time.
-
Accumulated dust may cause
fire or an electric shock from
deterioration or
electric leakage.
a
Only
use
teries.
-
the
specified
bat-
This make cause damaged the
Monitor or could give an electric
shock.
SafetyinsrucoMOvwCBplmP&d
Others
1.5V
1.5V
11
Front Panel Controls
<Front Panel Controls>
POWER
ON OFF
MENU
POWER
ON OFF
INPUT
VOL
MENU
VOL
SELECT
INPUT
SELECT
/I
Remote control
/I
sensor
Power standby indicator
Illuminates orange in standby mode, Illuminates green
when the Monitor is turned
Sub power button
Main power button
MENU button
INPUT SELECT button
VOLUME (
D
12
,
buttons
,G
) buttons
on
Connection Panel Overview
<Back Panel>
()
L
EXTRNALSPK(6)
Ω
()
()
R
()
DC OUTPUT
R AUDIO L
MONO
Y
VIDEO
(DC 12V)
PB
PR
AC INPUT
S-VIDEO
AV INPUT
R
COMPONENT(DVD/DTV
INPUT)
DC OUTPUT (DC 12V) jack
The DC OUTPUT jack is
optional item.
-
Input / COMPONENT
(DVD/DTV) INPUT jacks /
A/V
S-video
AUDIO
L
RGB 2 INPUT
RGB INPUT)
(DIGITAL
AC INPUT
RGB 1 INPUT
RS 232C INPUT
(PC/DTV INPUT)
(CONTROL/SERVICE)
jack
Audio Input sound (R)(L)jacks
RGB-1 (PC/DTV INPUT)
RGB-2 (DIGITAL RGB INPUT) jack /
RS-232C jacks
-
-
Input RGB2(Digital RGB) when input
signal supporting DVI-D.
You can use it from jacks.
SafetyinsrucoMOvwCBplmP&d
Others
13
Remote Control
-
When
using
Key
the remote control aim it at the remote control
Functions
sensor on
the Monitor.
POWER
POWER button
SLEEP button (Refer to p. 31)
SLEEP
INPUT SELECT
APC
DASP
APC button
ARC
PIP ARC
PIP
TWIN PICTURE
SWAP
SUB INPUT
ARC button
PIP button
SWAP button
MENU
MUTE
MENU button
ENTER button
ENTER
VOL
1
2
3
4
5
6
7
8
9
VOL
VOL buttons
0
PIP buttons
14
WIN.SIZE
WIN.POSITION
ZOOM-
ZOOM+
input select button
on
the remote
control
Each press of this button
mode
as
changes
the
shown below.
RGB1
RGB2
COMPONENT
INPUT SELECT button
DASP button (Refer to p. 34)
S-VIDEO
VIDEO
PIP ARC select button
TWIN PICTURE button
(Refer
to p.
42~46)
SUB INPUT button
MUTE button
switches the sound
on or
off.
UP/DOWN buttons
SafetyinsrucoMOvwCBplmP&d
Others
15
Accesories/Optional
extras
Accesories
POWER
SLEEP
INPUT SELECT
APC
DASP
ARC
PIP ARC
PIP
TWIN PICTURE
SWAP
SUB INPUT
MENU
VOL
1
MUTE
ENTER
VOL
2
3
4
5
6
7
8
9
1.5V
1.5V
0
WIN.SIZE WN.POSITION
ZOOM-
ZOOM+
Remote control
Owner's Manual
PC sound cable
D-sub 15
pin
cable
CH3
CH2
CH1
Power cord
Alkaline batteries
video cable
DVI
CH4
CHS/W
CH4
CH3
CHSW
Speaker
cable
CH2
CH1
A/V wireless
transmitter-receiver
(option)
Optional
Speaker
16
Extras
Tilt wall
mounting
braket
computer cable
the remote control
Using
Installing
batteries
?
the
Open
battery compartment
cover on
the back
of the remote control and insert the batteries with
correct
polarity,
match "+" with "+", and match
"-"
with "-".
?
Install two 1.5V "AAA" alkaline batteries.
Don't mix used batteries with
Notes for
Make
sure
objects
using
these
are no
between the
new
batteries.
the remote control
Don't
place
near a
the remote control
heater
remote control and its
Strong impact
sensor.
trol may
or
cause
on
damp place.
the remote
operation
con-
failure.
Signal
from the remote control
may be disturbed by sun light or
other strong light. In this case,
turn the set to other direction.
SafetyinsrucoMOvwCBplmP&d
Others
17
VCR
-
Setup
As shown below, when connecting the Monitor to a VCR, match the colors of AV input
jacks on the Monitor with the output jacks on the VCR: Video = yellow, Audio (Left) =
white, Audio (Right)
-
-
-
=
red.
If you have a mono VCR, connect the audio cable from the VCR to the AUDIO
input of the Plasma Monitor.
If you connect an S-VIDEO VCR to the S-VIDEO input, the picture
compared to connecting a regular VCR to the Video input.
quality
is
(L/MONO)
improved,
having a fixed image remain on the screen for a long period of time. A frozen still
picture from a VCR (or if a CH label is displayed) displayed on the screen for prolonged
periods will result in an image ghost remaining even when you change the image. Avoid
prolonged display of a still image.
Avoid
S-VIDEO
OUT
(R)
AUDIO
(L)
VIDEO
IN
Back
panel
of VCR
Tips
?
18
To avoid picture noise (interference), leave
between the VCR and monitor.
an
adequate
distance
(20
inches
or
more)
DC OUTPUT
R AUDIO L
MONO
(DC 12V)
Y
VIDEO
PB
PR
AC INPUT
O
AV INPUT
R
AUDIO
COMPONENT(DVD/DTV INPUT)
Back
L
RGB 2 INPUT
RGB INPUT)
(DIGITAL
panel
RGB 1 INPUT
RS 232C INPUT
(PC/DTV INPUT)
(CONTROL/SERVICE)
of the Monitor
To watch VCR
INPUT SELECT
1
2
Press INPUT SELECT button
on
the
remote control and select VIDEO.
(When connecting
S-VIDEO.)
with S-Video, select the
SafetyinsrucoMOvwCBplmP&d
Others
Insert a video tape into the VCR and press
the PLAY button on the VCR. See VCR
owner's manual.
19
Cable TV
-
Setup
subscribing to a cable TV service from a local provider and installing a converter,
you can watch cable TV programming. This monitor cannot display TV programming
without a TV tuner or cable TV converter box.
After
DC OUTPUT
R AUDIO L MONO
(DC 12V)
Y
VIDEO
PB
PR
AC INPUT
S-VIDEO
AV INPUT
R
COMPONENT
AUDIO
L
RGB 2 INPUT
RGB INPUT)
(DVD/DTV INPUT)
(DIGITAL
Monitor back
(AUDIO
RGB 1 INPUT
RS 232C INPUT
(PC/DTV INPUT)
(CONTROL/SERVICE)
panel
VO
TV
VCR
RF
Cable
Cable box
To watch cable TV
Press INPUT SELECT button
1
on
the
remote control and select VIDEO source.
Tune to cable service
2
using
provided
INPUT SELECT
channels
the cable box.
Tips
?
20
For further information regarding cable TV service, contact your local
cable TV service provider(s).
External AV Source
-
Setup
As shown below, when connecting the Monitor to an external source, match the
colors of AV input jacks on the Monitor with the output jacks on the audio/video
Video
equipment:
DC OUTPUT
yellow,
=
R AUDIO L MONO
PB
(Left)
=
white, Audio (Right)
PR
panel
R
COMPONENT
=
red.
AC INPUT
S-VIDEO
AV INPUT
Back
Y
VIDEO
(DC 12V)
Audio
(DVD/DTV INPUT)
AUDIO
L
RGB 2 INPUT
RGB INPUT)
(DIGITAL
RGB 1 INPUT
RS 232C INPUT
(PC/DTV INPUT)
(CONTROL/SERVICE)
of the Monitor
Camcorder
R
AUDIO
L
VIDEO
Video game set
DDR
To watch external AV
1
2
Press INPUT SELECT button
on
source
the
remote control of the monitor to select
INPUT SELECT
VIDEO.
Operate
the
SafetyinsrucoMOvwCBplmP&d
Others
corresponding external equipequipment operating
ment. See external
guide.
21
DVD
Setup
How to connect
?
?
DVD
a
(digital
video disk
player)
Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD/DTV
inputs to Audio jacks of AV INPUT.
Component Input is available to 480i, 480p, 720p, 1080i mode.
INPUT)
Back
DC OUTPUT
R AUDIO L MONO
(DC 12V)
Y
VIDEO
PB
PR
R
COMPONENT
?
L
RGB 2 INPU
RGB INP
(DIGITAL
AUDIO
Back
?
AUDIO
(DVD/DTV INPUT)
(R)
How to
(L)
panel
use
Press INPUT SELECT button on the remote control of the
monitor to select COMPONENT. Use the DVD player
according to its owner's manual.
Turn on the DVD player, and insert a DVD.
of
a
?
DVD
RGB 1 INPUT
RS 232C INPUT
T)
(PC/DTV INPUT)
(CONTROL/SERVICE)
B
R
of the Monitor
player
Component Input ports
Connect DVD player jacks to Monitor
Component input jacks as indicated below.
Component input jacks
on
Video
the Monitor
output jacks
of DVD
22
panel
AC INPUT
S-VIDEO
AV INPUT
and audio
player
YPBPR
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
DTV
-
To watch
Setup
digitally
broadcast programs,
purchase/connect
a
digital SET-TOP BOX.
How to connect
?
?
can use either the Monitor's COMPONENT (DVD/DTV INPUT) inputs
RGB1(PC/DTV INPUT) for video connections, depending on your Set Top
Then, make the corresponding Audio connections.
DTV Input is available to 480p, 720p, 1080i mode.
You
DC OUTPUT
R AUDIO L MONO
Y
VIDEO
(DC 12V)
S-VID
Back
panel
PB
PR
AC INPUT
O
R
COMPONENT
AV INPUT
the single
Box connectors.
or
(DVD/DTV INPUT)
AUDIO
L
RGB2IN
RGB
(DIGITAL
T
PUT)
RGB 1 INPUT
(PC/DTV INPUT)
RS 232C
(CONTROL/S
PUT
RVICE)
of the Monitor
or
(R)
Back
How to
?
Turn
on
(Refer
?
AUDIO
Y
(L)
panel
of
a
PB
PR
(R)
AUDIO
(L)
DTV OUTPUT
digital SET-TOP BOX
use
the
digital SET-TOP BOX.
digital SET-TOP BOX.)
the remote control to select COMPONENT
to the owner's manual for the
Press INPUT SELECT button
on
or
RGB1.
SafetyinsrucoMOvwCBplmP&d
Others
23
Connecting to a wireless
trasmitter (option)
?
?
Only adjust this function in some models.
connecting the wireless transmitter with external equipments,
connecting ports (Video yellow, Audio(L) white, Audio(R) -red).
When
-
?
?
match the colors of
-
If you have a mono VCR, connect the audio cable from the VCR to the AV input of the wireless
AV transmitter.
See the wireless trasmitter-receiver operating guide for installation and connection etc.
a
CH4
CH3
CH2
CH1
CH
S/W
d
Transmitter
rear
AV OUTPUT AV INPUT 12V DC INPUT
c
b
S VIDEO
OUT
(R) AUDIO (L)
VIDEO
VCR
rear
IN
VCR
CAMCORDER
How to connect
a.
Turn the power button of a transmitter on, and adjust desired channel with channel button and
the Place the wireless AV transmitter toward the wireless receiver.
b. Connect the output ports of the VCR to the AV OUTPUT port of the wireless AV transmitter.
c.
Connect the
adaptor
d. Connect the power
24
to the DC
plug
input
of the wireless AV transmitter
to the wall outlet socket after
connecting
.
the power cord to the
adaptor.
Connecting to a wireless
receiver (option)
?
?
Only adjust this function in some models.
connecting the wireless receiver with external equipments,
necting ports (Video yellow, Audio(L) white, Audio(R) -red).
When
-
match the colors of
con-
-
a
CH4
CH3
CH2
CH1
Receiver
rear
CH
S/W
AV INPUT
b
DC
UT
12V D
INPUT
c
R AUDIO
L
MONO
Y
VIDEO
(D)
PB
PR
AC INPUT
S-VIDEO
AV INPUT
R
COMPONENT (DVD/DTV
Back
INPUT)
panel
AUDIO
L
RGB 2 INPUT
RGB INPUT)
(DIGITAL
RGB 1 INPUT
RS 232C INPUT
(PC/DTV INPUT)
(CONTROL/SERVICE)
of the Monitor
How to connect
a.
Turn the power button of a receiver on, and adjust channel number same to the channel number of a transmitter with the channel button. Place the wireless AV receiver toward the wireless transmitter.
b. Connect the AV
c.
input ports
of the Monitor to the AV INPUT port of the receiver.
Connect the DC output of the monitor to DC
input
of the wireless receiver with DC cable.
25
SafetyinsrucoMOvwCBplmP&d
Others
PC
-
You
can
Setup
Setup
?
connect the Plasma
easily
Display
to your PC for
Instructions to Connect
To
setup this monitor in your PC window environment, select Normal, Standard or Default Monitor.
This monitor does not support Plug and Play funcThe
screen
over
?
does not
port
Connect the audio cable from the PC to the Audio
?
?
when the resolution is
ports of the Monitor.
If your PC computer is equipped with
adjust the sound output on the PC.
?
UXGA.
Connect the
on
display
on
Select the
display
cable from the monitor
sound card,
picture.
This monitor's
reso-
lution is 1280X768.
Output
RGB1(PC/DTV INPUT) port
the PC to the
a
resolution of the PC to
1024X768 for the best
signal
and sound.
PC to your Monitor
a
tion
?
outstanding image
the Monitor.
DC OUTPUT
R AUDIO L MONO
How to
PB
PR
AC INPUT
S-VIDEO
panel
R
COMPONENT (DVD/DTV
AV INPUT
Back
Y
VIDEO
(DC 12V)
AUDIO
INPUT)
RGB 2 INPUT
RGB INPUT)
(DIGITAL
RS 232C INPUT
C/
T)
(CONTROL/SERVICE)
of the Monitor
use
PC
?
Setup
computer and press the ON/OFF button on the
power to it. Second, turn on the display by pressing
the
button on the Monitor or by pressing the POWER button on
the Monitor's remote control.
Use the INPUT SELECT button on the remote control to select the
RGB1 input source.
Set the resolution output of the PC to SXGA or under (1280 x 1024,
First,
turn
Monitor to
INPUT SELECT
?
On the remote control
?
on
the PC
apply
75Hz).
Tips
?
Avoid
keeping a fixed image on the Monitor's screen for a long period of time. The fixed image may
permanently imprinted on the screen; use a screen saver when possible.
Change the resolution of PC to displayable mode (Refer to page 27) and connect to RGB1 Input
(PC/DTV Input) jacks of the monitor.
become
?
26
Monitor
Image Display Specifications (RGB1)
Resolution
Horizontal
Vertical
Frequency (KHz) Frequency (Hz)
640x350
720x400
640x480
800x600
1024x768
1152x864
1280x960
1280x1024
832x624(MAC)
31.468
70.09
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
37.861
72.80
37.500
75.00
43.269
85.00
53.011
100.04
64.062
120.00
35.156
56.25
37.879
60.31
48.077
72.18
46.875
75.00
53.674
85.06
56.000
90.00
64.016
100.00
48.363
60.00
56.476
70.06
60.023
75.02
68.677
84.99
54.348
60.05
67.500
75.00
77.487
85.05
60.000
60.00
75.000
75.00
63.981
60.02
79.976
75.02
49.725
74.55
Others
Tips
?
?
form : separate
Dos mode may not work depending on video card if
SafetyinsrucoMOvwCBplmP&d
Synchronization input
using
a
DVI-I cable.
27
Monitor
Image Display Specifications (RGB2)
Resolution
Vertical
Frequency (KHz) Frequency (Hz)
31.468
70.09
37.861
85.08
31.469
70.08
37.927
85.03
31.469
59.94
37.861
72.80
37.500
75.00
43.269
85.00
35.156
56.25
37.879
60.31
48.077
72.18
46.875
75.00
53.674
85.06
48.363
60.00
56.476
70.06
60.023
75.02
68.677
84.99
54.348
60.05
67.500
75.00
77.487
85.05
60.000
60.00
75.000
75.00
1280x1024
63.981
60.02
832x624(MAC)
49.725
74.55
640x350
720x400
640x480
800x600
1024x768
1152x864
1280x960
28
Horizontal
Turning
-
When
the remote
using
Turning
aim it at the
the Monitor
just
Connect power cord
1
the Monitor
sensor on
the Monitor.
after installation
correctly.
Press the main ON OFF button on the Monitor. At this moment, the Monitor is
switched to standby mode. Press the
or INPUT SELECT button on the
Monitor or press the POWER or INPUT SELECT button on the remote control
and then the Monitor will be turned on.
2
Turning
1
on
control,
on
on
the Monitor
(power
cord is still
connected)
If the Monitor is turned off with the remote control button.
Press the
or INPUT SELECT button on the Monitor or press the POWER
INPUT SELECT button on the remote control and then the Monitor will be
turned on.
or
2
3
If the Monitor is turned off with the ON OFF button
?
Press the main ON OFF button
on
the Monitor
on
the Monitor to turn
on
the Monitor.
If the Monitor is turned off with the remote control and also the ON OFF
button on the Monitor
?
Press the main ON OFF button on the Monitor and then press the
or
INPUT SELECT button on the Monitor or press the POWER or INPUT
SELECT button on the remote control and then the Monitor will be turned
Tips
Adjusting volume level
The volume(G ) button increases
on.
Others
?
the level of sound.
the sound and the
volume( )
SafetyinsrucoMOvwCBplmP&d
button reduces
29
Checking
-
-
1
Use the remote control to make
Select VIDEO
input
features
adjustments.
source.
Press the MENU button.
Press the UP/DOWN button.
2
?
Each press will
cycle through
the
menus
shown below.
PICTURE
SOUND
APC
DASP
CONTRAST
TREBLE
BRIGHTNESS
BASS
COLOR
BALANCE
SHARPNESS
TINT
SCREEN
D
D
MOVE
EXIT
menu
<Picture
MOVE
EXIT
menu
E
E
<Sound
menu>
menu>
SPECIAL
LANGUAGE
COLOR TEMP.
R-ADJUST
G-ADJUST
B-ADJUST
SCREEN SAVER
SET ID
D
MOVE
menu
EXIT
E
<Special
TWIN/PIP
PICTURE ADJ.
TWIN
AUTO. CONFIG.
PIP
ARC(MAIN)
INPUT
INPUT
(MAIN)
(SUB)
ZOOM IN/OUT
POSITION
WINDOW SIZE
CLOCK ADJUST
WINDOW POSITION
PHASE ADJUST
WINDOW RESET
D
MOVE
menu
RESET
D
EXIT
E
menu
EXIT
menu>
<Picture
adj.
menu>
Press the VOL ( G ) button to select a feature to adjust, and then
press the UP/DOWN buttons to adjust the selected item.
?
30
MOVE
E
<Twin/pip
3
menu>
Press the MENU button to exit.
Setting Sleep
Sleep Timer turns the
SLEEP
Timer
Monitor off after
preset time
a
Press the SLEEP button to set sleep time.
Each time you press SLEEP button, the next preset setting time is changed as follows:
OFF
10
20
30
120
90
60
240
180
SLEEP:
?
10
To release sleep time setting, press the SLEEP
button repeatedly to select OFF.
Tips
?
?
To check remaining sleep time after setting, press the SLEEP or ENTER
button just once.
If you turn the Monitor off after setting the sleep timer, the setting is erased.
The sleep timer will then have to be set again.
SafetyinsrucoMOvwCBplmP&d
Others
31
Auto
control
picture
Use APC to set the Monitor for the best
APC
picture appearance
(Auto Picture Control)
APC
1
2
Press the APC button.
Press the APC or UP/DOWN buttons to select your
desired picture condition.
APC
CLEAR
SOFT
USER
D
E
?
32
A
EXIT
Each press of APC button or UP/DOWN buttons
the screen display as shown below.
CLEAR
?
ADJUST
SOFT
You can also select CLEAR, SOFT
PICTURE menu.
changes
USER
or
USER in the
Adjusting picture appearance
READY
Press the MENU button and then press the UP/DOWN button
to select PICTURE menu.
Press the VOL
(
G
)
button.
MENU
1
VOL
Press the UP/DOWN button to select
CONTRAST and then press the
VOL ( G ) button.
PICTURE
APC
CONTRAST
G
100
BRIGHTNESS
COLOR
SHARPNESS
TINT
SCREEN
D
VOL
2
E
Use the VOL buttons to make approand then press the
ENTER button.
priate adjustments
MOVE
PREV.
F
CONTRAST 80
FG
ADJUST
D
E
?
VOL
?
MOVE
A
PREV.
Press the UP/DOWN buttons to select other
items.
VOL
ENTER
Adjust BRIGHTNESS, COLOR,
SHARPNESS and TINT in the
same
SafetyinsrucoMOvwCBplmP&d
Others
way.
33
Auto Sound Control
DASP
?
DASP
(Digital
Auto Sound
Processing)
This function lets you enjoy the best sound without any manual adjustment
because the Monitor automatically selects the appropriate audio tone levels
based on the program content.
1
Press the DASP button.
2
Press the DASP
sound setup.
or
UP/DOWN button to select
a
DASP
NORMAL
CINEMA
MUSIC
SPORTS
USER
D
E
?
ADJUST
A
EXIT
Each press of DASP or UP/DOWN buttons
display as shown below.
changes
the
screen
NORMAL
CINEMA
USER
?
34
MUSIC
SPORTS
You can also select NORMAL, CINEMA, MUSIC,
SPORTS or USER in the SOUND menu.
Adjusting Sound
Manual
Settings
SafetyinsrucoMOvwCBplm
READY
Press the MENU button and then press the UP/DOWN button
to select SOUND menu.
Press the VOL
(
G
)
button.
MENU
1
VOL
Press the UP/DOWN button to select
TREBLE and then press the VOL ( G
button.
)
SOUND
DASP
TREBLE
G
100
BASS
BALANCE
VOL
D
MOVE
F
PREV.
E
2
Picture&Sond
Specialfturs
Use the VOL buttons to make appropriate
adjustments and then press the ENTER
button.
Press the UP/DOWN buttons to select other items.
?
SOUND
VOL
VOL
DASP
ENTER
TREBLE
50
BASS
BALANCE
FG ADJUST A
?
Adjust
BASS and BALANCE in the
same
PREV.
way.
Others
35
Selecting language
for the
menus
READY
Press the MENU button and then press the UP/DOWN button
to select SPECIAL menu.
Press the VOL
(
G
)
button.
MENU
1
VOL
Press the UP/DOWN button to select
LANGUAGE and then press the
VOL ( G ) button.
SPECIAL
˙--
LANGUAGE
"
¢"
ENGLISH
COLOR TEMP.
R-ADJUST
G-ADJUST
B-ADJUST
SCREEN SAVER
VOL
SET ID
D
E
2
MOVE
F
PREV.
Press the UP/DOWN button to select
the desired language.
SPECIAL
˙-"
LANGUAGE
COLOR TEMP.
ENGLISH
R-ADJUST
G-ADJUST
B-ADJUST
SCREEN SAVER
SET ID
D
E
3
Press the ENTER button.
ENTER
36
MOVE
A
PREV.
color temperature
Adjusting
READY
SafetyinsrucoMOvwCBplmP&d
Press the MENU button and then press the UP/DOWN button
to select SPECIAL menu.
Press the VOL
(
G
)
button.
MENU
1
VOL
Press the UP/DOWN button to select
COLOR TEMP. and then press the
VOL ( G ) button.
SPECIAL
LANGUAGE
COLOR TEMP.
NORMAL
G
R-ADJUST
COOL
G-ADJUST
WARM
B-ADJUST
USER
SCREEN SAVER
SET ID
VOL
D
MOVE
E
2
Press the UP/DOWN button to select
your desired color temperature and then
press the ENTER button.
F
PREV.
SPECIAL
LANGUAGE
NORMAL
COLOR TEMP.
ENTER
R-ADJUST
COOL
G-ADJUST
WARM
B-ADJUST
USER
SCREEN SAVER
SET ID
D
E
3
MOVE
A
PREV.
Specialfturs
Press the UP/DOWN button to select R-ADJUST, G-ADJUST
and B-ADJUST in the same way.
Others
?
Press the VOL
(
F
)
button
again
to move other menu.
37
Using
-
the Screen Saver function
Prolonged display
of
a
still
image may
permanent image
cause a
to be 'burnt' on the
screen
-
-
If you select Screen Saver "ON", to prevent the permanent image, the picture moves a
little by the sequence of "Right-Bottom-Left-Up" every 10 minutes.
"SCREEN SAVER" function will help to prevent the effect of the permanent image but it
is possible to permanently burn the screen with a prolonged still image !
READY
Press the MENU button and then press the UP/DOWN button
to select SPECIAL menu.
Press the VOL
(
G
)
button.
MENU
1
VOL
Press the UP/DOWN button to select
SCREEN SAVER and then press the
VOL ( G ) button.
SPECIAL
LANGUAGE
COLOR TEMP.
R-ADJUST
G-ADJUST
B-ADJUST
SCREEN SAVER
D
MOVE
E
2
OFF
G
ON
SET ID
VOL
Press the UP/DOWN button to select
ON and then press the ENTER button.
F
PREV
SPECIAL
LANGUAGE
COLOR TEMP.
R-ADJUST
G-ADJUST
B-ADJUST
OFF
SCREEN SAVER
ENTER
ON
SET ID
D
E
?
38
Press the VOL
(
F
)
button
again
to move other menu.
MOVE
A
PREV
Setting picture format
-
possible in RGB1(PC)
RGB1(DTV) mode.
Wide and normal size
size
are
ARC
possible
in
are
and RGB2 mode, and Wide, normal and
Press the ARC button to select
format.
?
a
desired
zoom
picture
Each time you press ARC buttons, you can select
or ZOOM alternatively.
WIDE, NORMAL
WIDE
<WIDE>
NORMAL
<NORMAL>
ZOOM
Others
<Zoom>
?
You can also select WIDE, NORMAL
PICTURE menu.
or
SafetyinsrucoMOvwCBplmP&d
ZOOM in the
39
Using
the Zoom in/out function
READY
Press the MENU button and then press the UP/DOWN button
to select PICTURE ADJ. menu.
Press the VOL
(
G
)
button.
MENU
1
VOL
Press the UP/DOWN button to select
ZOOM IN/OUT and then press the
VOL ( G ) button.
PICTURE ADJ.
AUTO. CONFIG.
ADJUST
ARC(MAIN).
ZOOM IN/OUT.
G
POSITION
G
0
CLOCK ADJUST
PHASE ADJUST
VOL
RESET
D
E
2
Press the VOL buttons to
in or out.
adjust
MOVE
F
PREV
desired
zoom
PICTURE ADJ.
AUTO. CONFIG.
ADJUST
ARC(MAIN).
VOL
VOL
ZOOM IN/OUT
FG
POSITION
10
CLOCK ADJUST
PHASE ADJUST
RESET
A
?
40
You
can zoom
in
on
the
image upto
50x.
PREV.
Moving
-
Adjust
the
screen
the
with 'ZOOM IN/OUT' function to
picture
use
the 'POSITION' function.
READY
Press the MENU button and then press the UP/DOWN button
to select PICTURE ADJ. menu.
Press the VOL
(
G
)
button.
MENU
VOL
Press the UP/DOWN button to select
POSITION and then press the VOL (
button.
1
G
)
PICTURE ADJ.
AUTO. CONFIG.
ADJUST
ARC(MAIN).
ZOOM IN/OUT
POSITION.
D
G
F
VOL
G
E
CLOCK ADJUST
PHASE ADJUST
RESET
D
MOVE
F
E
PREV.
Press the VOL buttons or UP/DOWN
button to adjust to the desired picture
2
position.
PICTURE ADJ.
AUTO. CONFIG.
ADJUST
ARC(MAIN).
ZOOM IN/OUT
VOL
VOL
D
F
POSITION
G
E
CLOCK ADJUST
PHASE ADJUST
RESET
A
PREV.
Initializing
?
To initialize the adjusted value, select "RESET" with the UP/DOWN button and then press
the VOL(G ) button.
41
SafetyinsrucoMOvwCBplmP&d
Others
Picture in
-
-
-
picture (PIP)
function
PIP/TWIN PICTURE will let you view two seperate inputs on your monitor screen at the same time.
Color of main picture may be different from PIP's in PIP/TWIN PICTURE.
When the main picture is RGB1/DTV(more than 480p)/RGB2, the sub picture is Video/Svideo/DVD(480i) and when the main picture is Video/S- video/DVD(480i), the sub picture is
RGB1/DTV(more than 480p)/RGB2.
How to
use
the PIP
Press the PIP button.
PIP
?
It you press the PIP button
again,
the function is off.
PIP:ON
Adjusting
the size of sub
picture
Press the WIN. SIZE button to select
the size of sub picture.
?
Press
VOL(F
,
G
)
button to
adjust
desired size.
WIN.SIZE
WINDOW SIZE
FGADJ.
?
WIN. SIZE doesn't work when there is
Watching
sub
picture
as
4:3
or
no
signal
in
A
EXIT
sub-picture.
16:9
Press the PIP ARC button in PIP.
PIP ARC
?
Each time you press PIP ARC button, you
the pip size.
NORMAL
NORMAL
42
WIDE
WIDE
can
change
Moving
the sub
picture
Press the WIN. POSITION button in PIP.
?
Press the VOL(F G ) button and UP/DOWN button
adjust the position.
,
to
WIN.POSITION
WINDOW POS.
D
F
G
ADJ.
A
EXIT
E
Change
the main
picture
and the sub
picture
Press the PIP SWAP button in PIP.
SWAP
Viewing
RGB1
VIDEO
VIDEO
RGB1
External Source
Equipment
Press the PIP INPUT button in PIP.
RGB1
VIDEO
SUB INPUT
Tips
?
SafetyinsrucoMOvwCBplmP&d
Others
You can select WINDOW SIZE, WINDOW POSITION, PIP INPUT in the
TWIN/PIP menu.
43
Zoom in/out main
Viewing
External
picture
Equipment
Press the ZOOM+ button in PIP mode.
ZOOM+
ZOOM
25
D
F
POS.ADJ.
G
E
EXIT
A
?
?
Enlarge the picture with ZOOM+ button.
'ZOOM' is possible to 50.
Press the ZOOM- button to reduce the zoom effect.
Moving
the
enlarged picture
PresstheVOL(F,G)buttonor
adjust the position
UP/DOWN button to
of main picture.
?
It dose not operate when the 'ZOOM' is '0'.
ZOOM
25
D
F
G
POS.ADJ.
E
VOL
VOL
A
44
EXIT
Twin
How to
use
twin
picture
function
picture
Press the TWIN PICTURE button to
select desired twin picture.
TWIN PICTURE
?
Each time you press TWIN PICTURE buttons, you can
select TWIN1, TWIN2 or TWIN OFF alternatively.
TWIN1
TWIN2
TWIN 1
TWIN OFF
TWIN 2
TWIN OFF
Input
SUB INPUT
select of the sub
picture
Press the SUB INPUT button to select
the input select of sub menu.
VIDEO
RGB1
?
When the main
picture is RGB1/DTV(more than
picture is Video/S- video/DVD(480i)
and when the main picture is Video/Svideo/DVD(480i), the sub picture is
RGB1/DTV(more than 480p)/RGB2.
480p),
the sub
SafetyinsrucoMOvwCBplmP&d
Others
45
Twin
-
-
-
picture
function
PIP/TWIN PICTURE let you view different inputs on your monitor screen at the same time.
Color of main picture may be different from PIP's in PIP/TWIN PICTURE.
When the main picture is RGB1/DTV(more than 480p)/RGB2, the sub picture is Video/Svideo/DVD(480i) and when the main picture is Video/S- video/DVD(480i), the sub picture is
RGB1/DTV(more than 480p)/RGB2.
Changing
the
of main and sub
picture
Press the SWAP button in twin
picture
picture
mode.
SWAP
Size
VIDEO
RGB1
RGB1
VIDEO
adjusting
sub
picture
Press the WIN. SIZE button to select size of
sub picture in the twin picture.
?
Press
VOL(F
,
G
)
button to
adjust
desired size.
VIDEO
RGB1
WIN.SIZE
WINDOW SIZE
FGADJ.
46
?
WINDOW POSITION function doesn't work in the twin
picture
?
WINDOW SIZE function doesn't work when there is
signal
no
A
EXIT
mode.
of main/sub
picture.
Using
-
-
the
screen
options
This function works in Video and S-video modes.
Use this
option
to correct
trembling
or
picture instability
while
viewing
a
video tape.
SafetyinsrucoMOvwCBplmP&d
READY
Press the MENU button and then press the UP/DOWN button
to select PICTURE menu.
Press the VOL
(
)
G
button.
MENU
VOL
Use the UP/DOWN button to select
SCREEN and then press the
VOL ( G ) button.
1
PICTURE
APC
CONTRAST
BRIGHTNESS
COLOR
SHARPNESS
TINT
VOL
VCR
SCREEN
D
MOVE
E
2
Use the UP/DOWN buttons to select
TV or VCR.
?
?
Each time you press the
between TV and VCR.
TV
PREV
PICTURE
APC
Select the VCR option if watching a VCR.
Select the TV option for other equipment.
(Except VCR.)
?
G
F
CONTRAST
BRIGHTNESS
COLOR
SHARPNESS
VCR
TINT
D
/
E
button you
toggle
TV
SCREEN
D
E
MOVE
A
PREV
Specialfturs
3
Press the ENTER button to exit.
Others
ENTER
47
PC Mode Feature Check
Use the remote control to make
-
-
Select RGB 1
1
input
adjustments.
source.
Press the MENU button.
Press the UP/DOWN button.
2
?
Each press will
cycle through
the
menus
shown below.
SOUND
PICTURE
APC
DASP
CONTRAST
TREBLE
BRIGHTNESS
BASS
COLOR
BALANCE
SHARPNESS
TINT
SCREEN
D
D
MOVE
EXIT
menu
<Picture
MOVE
EXIT
menu
E
E
<Sound
menu>
menu>
SPECIAL
LANGUAGE
COLOR TEMP.
R-ADJUST
G-ADJUST
B-ADJUST
SCREEN SAVER
SET ID
D
MOVE
menu
EXIT
E
<Special
TWIN/PIP
PICTURE ADJ.
TWIN
AUTO. CONFIG.
PIP
ARC(MAIN).
INPUT(MAIN)
INPUT(SUB)
ZOOM IN/OUT
WINDOW SIZE
CLOCK ADJUST
POSITION
WINDOW POSITION
PHASE ADJUST
WINDOW RESET
D
MOVE
menu
RESET
D
EXIT
E
<Twin/pip
3
MOVE
menu
EXIT
E
menu>
<Picture
adj.
menu>
Press the VOL ( G ) button to select a feature to adjust, and then
press the UP/DOWN buttons to adjust the selected item.
?
48
menu>
Press the MENU button to exit.
PC Mode
-
This function works
only
Adjustment
in the RGB1 mode.
READY
Press the MENU button and then press the UP/DOWN button
to select PICTURE ADJ. menu.
Press the VOL
(
G
)
button.
MENU
1
VOL
Use the UP/DOWN button to select
AUTO CONFIG. and then press the
VOL ( G ) button.
PICTURE ADJ.
AUTO CONFIG.
G
TO SET
ARC(MAIN).
ZOOM IN/OUT
POSITION
CLOCK ADJUST
PHASE ADJUST
RESET
VOL
D
MOVE
F
E
2
When AUTO CONFIG. has finished,
'OK' will be shown on screen.
PREV
PICTURE ADJ.
AUTO. CONFIG.
OK
ARC(MAIN).
ZOOM IN/OUT
POSITION
CLOCK ADJUST
PHASE ADJUST
RESET
3
If the picture needed to be adjusted a little bit more after auto
adjustment, you can manually adjust the CLOCK ADJUST and
PHASE ADJUST adjustment.
Others
Tips
?
SafetyinsrucoMOvwCBplmP&d
The picture may appear strange while auto adjustment is taking place but that
is normal during. This process of searching for the best picture format.
49
PC Mode
-
Adjustment
position and CLOCK/PHASE adjustment work in RGB1(PC mode)
position only work in RGB(DTV mode-480p,720p,1080i).
Horizontal/Vertical
Horizontal/Vertical
and
READY
Press the MENU button and then press the UP/DOWN button
to select PICTURE ADJ. menu.
Press the VOL
(
G
)
button.
MENU
VOL
Use the UP/DOWN button to select
CLOCK ADJUST and then press the
VOL ( G ) button.
1
PICTURE ADJ.
AUTO. CONFIG.
ARC(MAIN).
ZOOM IN/OUT
POSITION
CLOCK ADJUST
0
G
PHASE ADJUST
VOL
RESET
D
MOVE
F
PREV
E
Use the VOL buttons adjust clock and
then press the ENTER button.
2
VOL
CLOCK ADJ.
ENTER
VOL
FG
ADJUST
+25
D
MOVE
A
PREV.
E
Adjust PHASE ADJUST
3
?
?
The
The
in the
same
way.
adjustment range of CLOCK ADJUST is -50 +50.
adjustment range of PHASE ADJUST is 0 31. (Based on the input
mode, the adjustment range of CLOCK ADJUST/PHASE ADJUST may
~
~
change.)
?
Based
on
the input signal, the position of the picture may not change even
have adjusted the CLOCK or PHASE position with this function.
though you
Initializing
?
50
To initialize the adjusted value, select "RESET" with the UP/DOWN button and then press
the VOL(G ) button.
-
External Control Device
Setup
Connect the RS-232C input jack
SELECT, MUTE) externally.
(such
to
a
PC and control the Monitor's functions
How to connect external control
?
Connect the RS-232C
(serial connector) input jack
as
ON/OFF,
INPUT
SafetyinsrucoMOvwCBplmP&d
equipment
with the
of moniter's RS-232C
rear
input jack.
?
RS-232C connection cables
DC OUTPUT
R AUDIO
L
MONO
(DC 12V)
Y
VIDEO
PB
are
not
PR
S-VIDEO
AV INPUT
with the Monitor.
supplied
AC INPUT
R
COMPONENT
(DVD/DTV INPUT)
AUDIO
L
RGB 2 INPUT
(DIGITAL
RGB
INPUT)
RGB 1
INPUT
(PC/DTV INPUT)
(C
NT
VIC
)
Specialfturs
Monitor Rear Connections Panel
Others
51
External Control Device
Setup
SET ID
?
Use this function to
specify
a
monitor ID number.
READY
Press the MENU button and then press the UP/DOWN
button to select SPECIAL menu.
Press the VOL ( G ) button.
MENU
1
VOL
Use the UP/DOWN buttons to select SET ID
and then press the VOL ( G ) button.
SPECIAL
LANGUAGE
COLOR TEMP.
R-ADJUST
G-ADJUST
B-ADJUST
SCREEN SAVER
VOL
SET ID
D
MOVE
G
F
E
2
1
PREV
Use the VOL button to adjust SET ID to
choose the desired monitor ID number and
then press the ENTER button.
SPECIAL
LANGUAGE
?
The
adjustment
range of SET ID is 1
99.
~
COLOR TEMP.
R-ADJUST
G-ADJUST
B-ADJUST
SCREEN SAVER
SET ID
VOL
52
VOL
1
ENTER
FGADJUST A
PREV.
External Control Device
-
The RS-232C
Type
input jack
of connector
No.
Pin
1
No connection
D-Sub
9-pin
using
RXD
3
TXD
DTR
5
GND
6
DSR
male
1
5
9
(DCE side ready)
(Ready to send)
(Clear to send)
7
RTS
8
CTS
9
No Connection
6
configurations
Command Reference List
NAME
3-wire
PC
2
TXD
TXD
3
RXD
GND
5
DTR
4
DSR
6
RTS
7
CTS
8
3254678
Data
:
115200bps (UART)
8 bits
length
Parity : None
?Stopbit:1bit
:
DTR
DSR
RTS
CTS
?
?
Communication code
*
Use the Crossed
:
ASCII code
cable.
0~1
0~4
b
c
0~2
04. Screen mute
k
d
0~1
05. Volume mute
k
e
0~1
06. Volume control
k
f
0~64
07. Contrast
k
g
0~64
08.
k
h
0~64
09. Color
k
i
0~64
10. Tint
k
j
0~64
11.
k
k
0~64
12. OSD select
k
l
0~1
13. remote control
k
m
0~1
Brightness
Sharpness
lock mode
14. PIP select
k
n
0~3
15. PIP size
k
o
0~1
16. PIP
k
q
0~3
17. Treble
k
r
0~64
18. Bass
k
s
0~64
19. Balance
k
t
0~64
20. Color
k
u
0~3
21. R
k
v
0~64
22.
k
w
0~64
k
$
0~64
select k
y
0~4
23.
(reverse)
DATA
a
k
DB9
Communication Parameters
Baud rate
GND
Command
k
03.
RXD
k
Input Select
Aspect Ratio
02.
LCD
DB9
Command
01. Power
configuration
(Not standard)
?
external control device.
(Receive data)
(Transmit data)
(DTE side ready)
4
?
an
name
2
RS-232C
:
is used to control the Monitor's functions
Setup
24.
position
temperature
adjust
G adjust
B adjust
Sub picture input
SafetyinsrucoMOvwCBplmP&d
Others
53
External Control Device
01. Power
Setup
(Command:a)
To control Power On/Off of the Monitor.
G
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data
0
:
Power Off
1:PowerOn
Acknowledgement
Transmission /
Protocol
Receiving
[a][ ][Set ID][ ][OK][Data][x]
Data
Transmission
0
:
Power Off
1:PowerOn
[Command1][Command2][ ][Set ID][ ][Data][Cr]
G
To
*
[Command1]
:
*
[Command2]
[Set ID]
:
To control LCD set.
:
You
or
*
can
adjust
Transmission
the set ID to choose
desired monitor ID number in
menu.
When
Adjustment
selecting Set
special
range is 1
ID '0', every
99.
(*
*
[DATA]
[k][a][ ][Set ID][ ][FF][Cr]
Acknowledgement
~
con
nected LCD set is controlled.
select
[a][ ][Set ID][ ][OK][data][x]
Data
Transmit
as
Hexadecimal
:
Power Off
1:PowerOn
code.)
To transmit command data.
:
*
Carriage
:
In like manner, if other functions transmit 'FF' data
on this format, Acknowledgement data feed
based
command.
[Cr]
0
'0', factory adjustment.
Transmit 'FF' data to read status of
*
To show Power On/Off.
mode
classify factory-adjustment
user adjustment mode.
back
Return
presents
status about each function.
ASCII code '0x0D'
*[]
Added to
:
classify command,
set ID
and DATA.
*
[Set ID], [Data]
:
Input
command with
2byte.
02.
Input
select
(Command:b)
OK Acknowledgement
G
[Command2][ ][Set ID][ ][OK][Data][x]
*
You
The Monitor transmits ACK
on
this format when
To select
based
(acknowledgement)
receiving normal data. At this
time, if the data is data read mode, it indicates present
status data. If the data is data write mode, it returns
the data of the PC computer.
on
this format when
non-viable functions
*
54
Data
:
(acknowledgement) based
receiving abnormal data from
or
code
communication
errors.
command is not
[01] illegal
(This
supported.)
[02] : not support function (This function doesn't work.)
[03] : wait more time (Try again a few minute later.)
:
source
on
for the Monitor.
an
input
source
[k][b][ ][Set ID][ ][Data][Cr]
Data
0
:
RGB1
1
:
Component
2
:
Video
3
:
S-Video
4
:RGB2
4
:RGB2
Acknowledgement
[b][ ][Set ID][ ][OK][Data][x]
Data
0
:
RGB1
1
:
Component
2
:
Video
3
:
S-Video
using
the INPUT
the Monitor's remote control.
Transmission
[Command2][ ][Set ID][ ][NG][Data][x]
The Monitor transmits ACK
input
also select
SELECT button
Error Acknowledgement
*
can
03.
G
Aspect
To
can
button
(Command:c)
screen
also
adjust
adjust
You
Ratio
the
the
screen
remote control
on
06. Volume control
(Command:f)
format.
or
format
using the ARC
Adj. menu.
G
in the Picture
To
volume.
adjust
You
also
can
volume with the VOL buttons
adjust
on
remote control.
Transmission
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data
0
:
1
:
2
:
Wide
[k][f][ ][Set ID][ ][Data][Cr]
(16:9)
Normal screen (4:3)
Full screen (Zoom)
screen
Data
Min:0~Max:64
*
Transmit
as
Hexadecimal code.
Acknowledgement
Acknowledgement
[c][ ][Set ID][ ][OK][Data][X]
[f][ ][Set ID][ ][OK][Data][X]
Data
*
0
:
1
:
2
:
Using
or
Wide
(16:9)
Normal screen (4:3)
Full screen (Zoom)
screen
the PC
Normal
input, you
screen(4:3).
Data
select either Wide
Min:0~Max:64
screen(16:9)
07. Contrast
G
To
adjust
You
04. Screen mute
G
To select
screen
(Command:d)
mute on/off.
Data
:
Screen mute off
1
:
Screen mute
on
(Picture on)
(Picture off)
0
:
Screen mute off
1
:
Screen mute
Data
on
can
also
adjust
Hexadecimal code.
Min:0~Max:64
(Picture on)
(Picture off)
(Command:e)
G
mute
using
Brightness (Command:h)
To
adjust
You
To control volume mute on/off.
You
as
[g][ ][Set ID][ ][OK][Data][X]
08.
G
Transmit
Acknowledgement
[d][ ][Set ID][ ][OK][Data][X]
05. Volume mute
menu.
Min:0~Max:64
*
Acknowledgement
Data
contrast in the Picture
[k][g][ ][Set ID][ ][Data][Cr]
[k][d][ ][Set ID][ ][Data][Cr]
0
contrast.
adjust
Transmission
Transmission
Data
screen
also
can
(Command:g)
the MUTE button
on
brightness.
adjust brightness
screen
also
can
in the Picture
menu.
Transmission
remote control.
[k][h][ ][Set ID][ ][Data][Cr]
Transmission
Data
[k][e][ ][Set ID][ ][Data][Cr]
Data
0
:
Volume mute
1
:
Volume mute off
on
Min:0~Max:64
*
(Volume off)
(Volume on)
Transmit
as
Hexadecimal code.
Acknowledgement
Acknowledgement
[h][ ][Set ID][ ][OK][Data][X]
[e][ ][Set ID][ ][OK][Data][X]
Data
Data
0
:
Volume mute
1
:
Volume mute off
on
SafetyinsrucoMOvwCBplmP&d
Others
Min:0~Max:64
(Volume off)
(Volume on)
55
External Control Device
09. Color
G
To
the
screen
also
adjust
adjust
You
can
12. OSD select
(Command:i)
menu.
Data
Min:0~Max:64
Transmit
as
Hexadecimal code.
Screen
on/off.
Display)
0
:OSDoff
1
:OSDon
Acknowledgement
Acknowledgement
[l][ ][Set ID][ ][OK][Data][X]
[i][ ][Set ID][ ][OK][Data][X]
Data
(On
[k][l][ ][Set ID][ ][Data][Cr]
[k][i][ ][Set ID][ ][Data][Cr]
*
(Command:l)
Transmission
Transmission
Data
To select OSD
G
color.
color in the Picture
Setup
Data
Min:0~Max:64
0
:OSDoff
1
:OSDon
13. Remote control lock mode
10. Tint
(Command:m)
(Command:j)
To set up the
G
G
To
the
screen
also
adjust
adjust
You
can
menu.
[k][m][ ][Set ID][ ][Data][Cr]
Acknowledgement
[k][j][ ][Set ID][ ][Data][Cr]
[m][ ][Set ID][ ][OK][Data][X]
Red:0~Green:64
Transmit
*
as
Data0:off
Hexadecimal code.
1:on
Acknowledgement
*
[j][ ][Set ID][ ][OK][Data][X]
Data
This function is
setting
mode when the remote control
is not used.
Red:0~Green:64
14. PIP select
G
11.
function of set remote control.
Transmission
tint.
tint in the Picture
Transmission
Data
locking
Sharpness (Command:k)
To control PIP
can
(Command:n)
(Picture-in-Picture)
picture
button
on
remote control
menu.
G
To
the
adjust
You
can
also
sharpness.
adjust sharpness in
screen
menu.
Transmission
Transmission
[k][n][ ][Set ID][ ][Data][Cr]
[k][k][ ][Set ID][ ][Data][Cr]
Data
Data
Min:0~Max:64
*
Transmit
as
Hexadecimal code.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][X]
Data
56
the Picture
Min:0~Max:64
0
:PIP/DWoff
1
:PIP
2
:
Twin
3
:
Twin
picture (DW1)
picture (DW2)
Acknowledgement
[n][ ][Set ID][ ][OK][Data][X]
Data
or
twin
also control PIP/TWIN PICTURE
0
:PIP/DWoff
1
:PIP
2
:
Twin
3
:
Twin
picture (DW1)
picture (DW2)
or
in
picture. You
using the pip/twin
the Twin/Pip
15. PIP size
(Command:o)
17. Treble
G
G
Transmission
Data
To
0
:
Normal
1
:
Wide
can
(4:3)
(16:9)
Data
:
Normal
1
:
Wide
16. PIP
You
can
position
also
Data
POSITION
on
the remote control
on
the TWIN/PIP
Transmit
as
Hexadecimal code.
menu.
Min:0~Max:64
18. Bass
picture position for PIP.
adjust the sub picture position using
button
or
the
G
To
adjust
You
in WINDOW
(Command:s)
can
the
also
screen
adjust
bass.
bass in the sound
[k][s][ ][Set ID][ ][Data][Cr]
[k][q][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
0
Right
:
down
1
:
Left down
2
:
Left up
3
:
Transmit
as
Hexadecimal code.
on screen
on screen
on screen
Right up on
Acknowledgement
menu.
Transmission
Transmission
Data
menu.
[r][ ][Set ID][ ][OK][Data][X]
(4:3)
(16:9)
position (Command:q)
To select sub
treble in the sound
Acknowledgement
screen
screen
adjust
Min:0~Max:64
*
[o][ ][Set ID][ ][OK][Data][X]
0
treble.
screen
[k][r][ ][Set ID][ ][Data][Cr]
Acknowledgement
Data
also
Transmission
screen
screen
the
adjust
You
[k][o][ ][Set ID][ ][Data][Cr]
G
(Command:r)
To select PIP size.
screen
Acknowledgement
[s][ ][Set ID][ ][OK][Data][X]
Data
Min:0~Max:64
[q][ ][Set ID][ ][OK][Data][X]
Data
down
0
:
Right
1
:
Left down
2
:
Left up
3
:
Right
on screen
on screen
on screen
up
on screen
19. Balance
G
To
adjust
You
can
(Command:t)
the
also
screen
adjust
balance.
balance in the sound
menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Transmit
as
Hexadecimal code.
Acknowledgement
[t][ ][Set ID][ ][OK][Data][X]
Data
SafetyinsrucoMOvwCBplmP&d
Others
Min:0~Max:64
57
External Control Device
20. Color temperature
G
To set up with
(Command:u)
'normal, cool,
warm, user' in the color
temperature.
23.
G
Setup
B-Adjust (Command:$)
To
adjust 'B-adjust'
in the color
temperature.
Transmission
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data
0
:
[k][$][ ][Set ID][ ][Data][Cr]
Normal
1
:Cool
2
:Warm
3
:User
Data
*
21.
as
Hexadecimal code.
[$][ ][Set ID][ ][OK][Data][X]
Data
[u][ ][Set ID][ ][OK][Data][X]
0
Transmit
Acknowledgement
Acknowledgement
Data
Min:0~Max:64
Min:0~Max:64
:Normal1:Cool2:Warm3:User
R-Adjust (Command:v)
24. Sub
G
To
adjust 'R-adjust'
in the color
temperature.
picture input
(Command:y)
select
Transmission
Data
[k][v][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Transmit
as
Hexadecimal code.
Acknowledgement
:
RGB1
1
:
Component
2
:
Video
3
:
S-Video
4
Data
Min:0~Max:64
Min:0~Max:4
*
Transmit
as
Hexadecimal code.
Acknowledgement
[y][ ][Set ID][ ][OK][Data][X]
Data
22.
G
G-Adjust (Command:w)
To
adjust 'G-adjust'
in the color
temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data
Min:0~Max:64
*
Transmit
as
Hexadecimal code.
Acknowledgement
[w][ ][Set ID][ ][OK][Data][X]
Data
58
Min:0~Max:64
:RGB2
[k][y][ ][Set ID][ ][Data][Cr]
[v][ ][Set ID][ ][OK][Data][X]
Data
0
Min:0~Max:4
Troubleshooting
No
picture
&
?
Check whether the Monitor is turned
?
Power cord inserted into wall outlet?
check list
on.
No sound
?
?
Press the VOLUME
?
Sound muted? Press MUTE button.
Picture OK &
No sound
?
The remote control
?
doesn't work
?
or
or
Poor color
Poor
picture
(G )
button.
Check to see if there is any object between the LCD Monitor
and the remote control causing obstruction.
Check to
see
if the batteries are installed with the correct
to 17 page)
polarities. (Refer
?
No
Plug another product's power cord into the wall outlet where
the Monitor's power cord was plugged in.
?
?
Install
new
batteries.
(Refer
to 17
page)
Select COLOR in the PICTURE menu and press the VOLUME (G ) button. (Refer to 33 page)
Increase the distance between the Monitor and the VCR.
Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the
screen
SafetyinsrucoMOvwCBplmP&d
Others
gets dark.)
59
Troubleshooting
No
output from one
of the speakers
Adjust
?
This is normal as the image is muted during the startup
process of the monitor.
Please contact your service center, if the picture has not
appeared after five minutes.
on
Horizontal/vertical
bars
?
picture
shaking
or
Strange
sound
from inside the
monitor
60
?
Check for local interference such
power tool.
A
menu.
as an
(Refer
to 35
?
Picture appears
slowly, after
switching
BALANCE in the SOUND
check list
electrical
page)
appliance
or
change in ambient humidity or temperature may result in an
unusual noise at the time of switching off or on of the monitor
and does not indicate a fault with the monitor.
Note
SafetyinsrucoMOvwCBplmP&d
Others
61
Note
62
Product
specifications
MW-30LZ10
MODEL
(inches
/
mm)
29.9 / 759
Height (inches
/
mm)
21.5 / 546
Depth (inches
/
mm)
7.1 / 179.5
/
40.6 / 18.4
Width
Weight (pounds
Power
kg)
requirement
AC 100-240V~ 50/60Hz
1280
Resolution
Colors
?
The
specifications shown
quality improvement.
x
768(Dot)
16,770,000 (256 steps of each R, G, and B)
above may be
changed
without
prior
notice for
SafetyinsrucoMOvwCBplmP&d
Others
63
P/NO
:
3828VA0338D b
(373-026H)
Download PDF