LG | RE-44NZ21RB | LG RE-44NZ21RB Owner’s Manual

Colour Television
OWNER'S MANUAL
Please read this manual
carefully
before
operating your
set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back cover and
mation to your dealer when you
Model number
:
Serial number
:
require
quote this infor-
service.
FOR THE GUARANTEE TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL
P/NO
:
3828VA0382D
(MP015D, 089B TX)
(3840VA0024A/B, 3840VA0016C, 373-026F)
a
Contents
Installation
3
Location and function of controls
Remote control handset
Internal generator charge
Front panel
4
Basic operation
On and off / Programme selection
Volume adjustment / Quick view
Mute function / Auto Demonstration
On screen language selection (option)
7
On
8
screen menus
Menu selection
up TV stations
Auto programme tuning
Manual programme tuning
Fine tuning
Programme edit
Calling the programme table
Setting
Picture adjustment
PSM (Picture Status Memory)
Picture adjustment / 100Hz mode
Auto convergence / Picture format
Turbo picture selection
14
Sound adjustment
SSM (Sound Status Memory) / Sound adjustment
Turbo sound selection
Sound output selection / Stereo/Dual reception
NICAM reception (option)
17
Other functions
TV and AV modes
Auto AV switching (option)
Child lock / Auto sleep
Blue back / Sleep timer
19
PIP
21
Teletext (option)
Switch on/off
SIMPLE text / TOP text (option)
FASTEXT / Special teletext functions
22
Connection of external equipment
Aerial socket
Euro scart socket
Audio/Video in sockets
S-video/Audio in sockets (S-AV)
Component in sockets
25
operation (option)
On and off / Input mode selection for sub picture
Swapping between main and sub pictures
Programme selection for sub picture
Sub picture size / Sub picture freeze
Sub picture position change / Programme scan
Troubleshooting
2
9
check list
27
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set.
In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
Warning
To prevent fire
moisture.
Wiring (in
shock hazard, do not expose the set to rain
or
U.K.
or
only)
This set is supplied with a BS 1363 approved 13 amp mains plug,
fused at 5 amp. When replacing the fuse always use a 5 amp BS
1362, BSI or ASTA approved type. Never use this plug with the fuse
cover omitted. To obtain a replacement fuse cover contact your
dealer or "LG Electronics U.K. Ltd."
If the
type of plug supplied is not suitable for the mains sockets in
your home, then the plug should be removed and a suitable type fitted. Please refer to the
Warning (in
U.K.
instructions below:
only)
A mains
plug removed
destroyed. A mains plug
a
wiring
from the mains lead of this set must be
with bared wires is hazardous if inserted in
mains socket.
Do not connect either wire to the earth pin, marked with the letter E
or with the earth symbol
or coloured green or green and yellow.
If any other plug is fitted,
the distribution board.
Important (in
U.K.
use a
5 amp
fuse, either in the plug,
or
at
only)
The wires in this mains lead are coloured in accordance with the following codes:
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your
plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black. The wire which
is coloured brown must be connected to the terminal which is
marked with the letter L or coloured red.
Service
Never
the back cover of the set as this can expose you to
very high voltage and other hazards. If the set does not operate
properly, unplug it and call your dealer.
remove
Aerial
Connect
the
aerial
Ω on the back cover.
should be used.
cable
to
the
socket
For the best reception an
marked
+ 75
outdoor aerial
Location
Position your set so that no bright light or sunlight falls directly onto
the screen. Care should be taken not to expose the set to any
unnecessary vibration, moisture, dust or heat. Also ensure that the
set is placed in a position to allow a free flow of air. Do not cover
the ventilation openings on the back cover.
Do not place the set on a sloping or unstable area as the casters
on the bottom of the set may cause it to move and to be damaged.
When displaying still pictures such as video games, 4:3
mat, PIP display, and station label for a long time, the
be persisted on the screen.
picture forimage may
Manufactured under license from Dolby Laboratories. "Dolby",
"Pro Logic" and the double-D symbol are trademarks of Dolby
Laboratories.
3
Location and function of controls
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
Only use the remote control handset supplied with this set. If you
use other remote control handsets, they'll not be able to use.
Remote control handset
POWER
TV/AV
Before you use the remote control handset,
10
teries. See the next page.
1
2
3
1
2
3
4
5
6
7
8
9
0
PSM
PICTURE
4
MENU
SOUND
5
TV/AV
selects TV or AV mode.
clears the menu / text from the screen.
switches the set on from standby.
2.
NUMBER BUTTONS
switches the set on from
11
SSM
I/II
1.
T
U
R
B
O
12
3.
13 4.
PR
6
VOL
VOL
OK
5.
PR
PIP
6.
MUTE
14
7
PIP PR
PIP PR
ARC
15
PIP INPUT
PIP SWAP
TEXT
16
SCAN
STILL
TIME
REVEAL
?
LIST
SLEEP
M
REW
PLAY
FF
P/STILL
STOP
REC
9
17 7.
18
directly
select
a
number.
Memory)
picture setting.
a menu.
/ Ε (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
Φ / Γ
(Volume Down/Up)
adjusts the volume.
Δ
menu
settings.
accepts your selection
i
MIX
MENU
selects
OK
SIZE
or
install the bat-
I/II
selects the language during dual language broadcast.
selects the sound output (option).
adjusts
8
POSITION
PSM (Picture Status
recalls your preferred
standby
please
or
displays
the current mode.
PIP BUTTONS
PIP
switches the sub picture on or off.
PIP PR +/selects a programme for the sub picture.
PIP SWAP
alternates between main and sub picture.
PIP INPUT
selects the input mode for the sub picture.
SIZE
adjusts
the sub
picture
size.
STILL
freezes motion of the sub picture.
POSITION
relocates the sub picture in clockwise direction.
SCAN
switches on or off the programme scan mode through 12 sub
pictures.
8.
PIP SWAP
returns to the
9.
viewed programme.
LIST
displays
4
previously
the programme table.
Location and function of controls
10. POWER
switches the set
on
from
standby
or
off to
standby.
11. SSM
(Sound Status Memory)
recalls your preferred sound setting.
12. TURBO PICTURE BUTTON
selects Turbo picture.
POWER
TV/AV
10
1
13. TURBO SOUND BUTTON
selects Turbo sound.
2
14. MUTE
switches the sound
on or
off.
15. ARC
(Aspect Ratio Control)
changes the picture format.
3
1
2
3
4
5
6
7
8
9
PSM
0
SSM
I/II
PICTURE
4
16. TELETEXT BUTTONS (option)
These buttons are used for teletext.
For further details, see the 'Teletext' section.
11
MENU
SOUND
5
T
U
R
B
O
12
13
PR
17. SLEEP
sets the
sleep
6
timer.
18. VCR BUTTONS
control a LG video cassette recorder.
VOL
VOL
OK
PR
PIP
MUTE
14
7
* : NO FUNCTION
PIP PR
Note In teletext mode, the PIP PR +/-, PIP SWAP and PIP INPUT
buttons are used for teletext function.
PIP INPUT
PIP PR
ARC
15
:
PIP SWAP
TEXT
16
8
POSITION
SCAN
STILL
SIZE
REVEAL
SLEEP
i
Internal
generator charge
MIX
TIME
?
The remote control handset can be charged with the internal elec- 9
tric generator. To charge the remote control handset carry out the
LIST
M
REW
PLAY
FF
P/STILL
STOP
REC
17
18
following;
1.
In first use,
20 rotation of the handle in the arrow direction as picture below
-> waiting for one minute -> 20 rotation again -> waiting for one
minute again -> 20 rotation again -> beginning to use
2. In usual use
5 or 6 rotation -> resuming to use
Note
Do not rotate the handle too
remote control handset.
:
rapidly for
the
protection of the
5
Location and function of controls
Front
panel
RE/RL-44/49/56NZ21 series
?
8
TV/AV
T/AV
MNU
OK
OL
MENU
VOL
OK
PR
PR
1
2
345
6
AV3
7
9
R
RE/RL-39NZ40 series
?
S-VIDEOL/MNAU
(Side panel)
8
TV/AV
1
TVV
MNU
OK
NDX
OL
MENU
OK
VOL
INDEX
PR
23410
1.
3.
4.
56
MAIN POWER
switches the set
2.
7.
on or
off.
TV/AV
selects TV or AV mode.
clears the menu / text from the screen.
switches the set on from standby.
MENU
selects
displays
AUDIO/VIDEO IN SOCKETS (AV3)
Connect the audio/video out sockets of external equipment to these sockets.
S-VIDEO/AUDIO IN SOCKETS (S-AV)
Connect the video out socket of an S-VIDEO
VCR to the S-VIDEO socket.
Connect the audio out sockets of the SVIDEO VCR to the audio sockets as in AV3.
10. INDEX
switches LED DISPLAY
LED
STEREO
SLEEP
LOCK
6
standby
(Light Emitting Diode) DISPLAY
illuminates brightly when the set is switched
Option : Only RE/RL-39NZ40 series,
: PAL/SECAM indicator
: NTSC indicator
: STEREO indicator
: SLEEP Timer indicator
: CHILD LOCK indicator
(Volume Down/Up)
adjusts the volume.
adjusts menu settings.
Δ / Ε (Programme Up/Down)
9.
mode.
6.
Γ
REMOTE CONTROL SENSOR
the current
POWER/STANDBY INDICATOR
illuminates brightly when the set is in
mode
goes off when the set is switched on.
/
8.
OK
or
Φ
7
selects a programme or a menu item.
switches the set on from standby.
a menu.
accepts your selection
5.
PR
on.
*
on or
CASTERS (on the bottom)
turn and move the set easily.
off.
Basic
operation
On and off
1.
2.
3.
4.
Press the main power button to switch the set on.
If the set is in standby mode, press the POWER, Δ / Ε, TV/AV or
NUMBER buttons on the remote control handset to switch it on fully.
Press the POWER button on the remote control handset.
The set reverts to standby mode.
Press the main power button again to switch the set off.
POWER
TV/AV
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains
plug is replaced in the mains power socket.
selection
Programme
You can select
buttons.
programme number with the
a
Δ
/
Ε
or
NUMBER
1
2
3
4
5
6
7
8
9
0
SSM
I/II
MENU
Volume
adjustment
Press the
Φ
/
Γ
button to
SOUND
T
U
R
B
O
PR
adjust
the volume.
VOL
OK
VOL
PR
MUTE
Quick view
Press the PIP SWAP button to view the last programme you
were
watching.
PIP SWAP
Mute function
Press the MUTE button. The sound is switched off and the
W appears.
You
can
SOUND,
cancel it by
SSM button.
pressing
the MUTE,
Φ
display
/ Γ, I/II, TURBO
Auto Demonstration
To review all the menus programmed in the set, press the OK button of the front panel control for about 10 seconds. To stop auto
demonstration, press any button of the front panel control and
POWER button of the remote control.
On
screen
language
selection
The menu can be displayed
First select your language.
1.
2.
3.
on
the
(option)
screen
in desired
language.
Press the MENU button to select the Station menu.
Press the Γ button and then Δ / Ε button to select Language.
Press the Γ button and then Δ / Ε button to select your desired
language.
4.
All the on screen displays will appear in the selected language.
Press the OK or Φ button to select the Station menu.
Press the TV/AV button to return to normal TV viewing.
7
On
The
screen menus
between you and your set takes place on screen with
an operator menu. The buttons required for the operating steps are
also displayed.
dialogue
Menu selection
1.
2.
3.
the MENU button to display each menu.
Press the Γ button and then Δ / Ε button to select a menu item.
Press the Γ button to display the sub menu or the pull-down
Repeatedly press
menu.
4.
Change
the
setting
of
an
item in the sub
or
Φ/ΓorΔ/Ε.
You
can move
to the
higher
level
to move to the lower level menu
pull-down
menu
with
with OK or Φ button and
press the Γ button
menu
Note :
In the AV modes, the Station menu is not displayed.
a.
b. In the teletext mode, menus are not displayed.
c.
On some models, the BG, L will display.
d. On some models, the Language will not display.
MENU
CH.
PR
VOL
OK
{
OBG
{
System
StorageOfrom
{
OOI
ProgrammeOedit
{
Start
{
ODK
Language
{
1
AutoOprogramme
ManualOprogramme
{
VOL
()O{OOKOMENUOTV
PR
AV
Station
CH.
AV
menu
PSM
{
PR.
{
User
{
System
{
100Hz
{
Channel
{
{
Fine
{
Search
{
Name
{
Booster
{
A u to
convergence
()O{OOKOMENUOTV
Picture
CH.
()O}{OOKOMENUOTV
AV
()O}{OOKOMENUOTV
AV
menu
SSM
{
0O-O-O-O-O- OO 05O SO 6O9
Balance
{
1O CO 0O3OO06O SO 1O7
AVL
{
2O CO 1O2OO07O SO 2O2
3O SO 6O6OO08O CO 0O9
4O SO 6O7OO09O CO 1O1
DeleteOOOCopy
MoveOOOOOSkip
()O{OOKOMENUOTV
Sound
CH.
()O}{OOKOMENUOTV
menu
Input
{
ChildOlock
{
AutoOsleep
{
BlueOback
{
()O{OOKOMENUOTV
Special
TV programme
8
AV
AV
menu
AV
Setting
TV
stations
up
Up to 100 TV stations can be stored by programme numbers (0 to
99). Once you have preset the stations, you will be able to use the
Δ / Ε or NUMBER buttons to scan the stations you programmed.
Stations can be tuned using automatic or manual modes.
Auto programme
tuning
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
()O{OOKOMENUOTV
Station
Menu
{
AV
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.
TV/AV
1.
2.
3.
the MENU button to select the Station menu.
button and then Δ / Ε button to select Auto pro-
Repeatedly press
Press the
Γ
gramme.
Press the Γ button to
display
the Auto programme
System
StorageOfrom
{
OBG
{
OOI
Start
{
ODK
menu.
1
2
3
4
5
6
7
8
9
0
OO
MENU
()O}{OOKOMENUOTV
AV
PR
Press the Γ button. Select a TV system with the Δ / Ε button
on the System pull-down menu;
L
: SECAM L/L' (France: SECAM-L models only)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
5. Press the OK or Φ button.
6. Press the Δ / Ε button to select Storage from.
7. Press the Γ button. Select the beginning programme number
with the Φ / Γ button or NUMBER buttons on the Storage
from pull-down menu. Any number under 10 is entered with a
numeric '0' in front of it, i.e. '05' for 5.
8. Press the OK button.
9. Press the Δ / Ε button to select Start.
10. Press the Γ button to begin auto programming.
4.
System
StorageOfrom
{
Start
{
VOL
OK
VOL
PR
{
OOCO01O(BG)
77O7O7O736%
MENU
All receivable stations are stored. The station name is stored for
stations which broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data.If no
station name can be assigned to a station, the channel number
is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47),
followed by a number.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the 'Programme edit' section
to edit the stored programme.
11. Press the TV/AV button to return to normal TV
viewing.
9
Setting
Station
Menu
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
()O{OOKOMENUOTV
{
Manual programme
4
7
2
5
8
tuning
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
AV
the MENU button to select the Station menu.
button and then Δ / Ε button to select Manual
1.
Repeatedly press
2.
Press the
3.
programme.
Press the Γ button to
TV/AV
1
TV
stations
up
3
6
9
Γ
display
the Manual programme
PR.
{
System
{
Channel
{
Fine
{
Search
{
Name
{
Booster
{
menu.
1
0
()O}{OOKOMENUOTV
4.
MENU
PR
VOL
AV
OK
PR
VOL
Press the Δ / Ε button to select PR..
5. Press the Γ button to select the programme number. Select the
desired programme number (0 to 99) with the Φ / Γ button or
NUMBER buttons on the PR. pull-down menu. Any number
under 10 is entered with a numeric '0' in front of it, i.e. '05' for
5.
6. Press the OK button.
7. Press the Δ / Ε button to select System.
8. Press the Γ button. Select a TV system with the Δ / Ε button
on the System pull-down menu;
L
: SECAM L/L' (France: SECAM-L models only)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
9. Press the OK or Φ button.
10. Press the Δ / Ε button to select Channel.
11. Press the Γ button. Press the Δ / Ε button to select V/UHF or
Cable on the Channel pull-down menu.
If possible, select the channel number directly with the number
buttons. Any number under 10 is entered with a numeric '0' in
front of it, i.e. '05' for 5.
12. Press the OK or Φ button
13. Press the Δ / Ε button to select Search.
14. Press the Γ button. Press the Φ / Γ button to commence
searching on the Search pull-down menu. If a station is found
the search will stop.
15. Press the OK button to store it. The display Stored will appear.
PR.
{
System
{
Channel
{
Fine
{
Search
{
Name
{
Booster
{
{{{{
Stored
16. To store another station, repeat steps 4 to 15.
17. Press the TV/AV button to return to normal TV
10
viewing.
Setting
TV
stations
up
Assigning a station name
1.
Repeat the 'Manual programme tuning' steps
2.
3.
4.
5.
6.
7.
CH.
1 to 3.
Press the Δ / Ε button to select Name.
Press the Γ button on the Name pull-down menu.
Press the Δ button. You can use a blank, +, -, the numeric 0 to 9
and the alphabet A to Z.
With the Ε button you can select in the opposite direction.
Select the position by pressing the Φ / Γ button and then take
your choice of the second character, and so on.
Press the OK button.
Press the TV/AV button to return to normal TV viewing.
Booster
If the reception is poor at the fringe area of TV signal, select
Booster to On. When the picture condition is good, do not select
Booster to On.
1.
2.
3.
4.
5.
6.
the 'Manual programme tuning' steps 1 to 3.
Press the Δ / Ε button to select Booster.
Press the Γ button.
Press the Δ / Ε button to select On or Off on the Booster
down menu.
Press the OK or Φ button.
Press the TV/AV button to return to normal TV viewing.
3.
fine
tuning
is
5.
6.
if
only necessary
{
Language
{
()O{OOKOMENUOTV
{
AV
TV/AV
1
2
3
4
5
6
7
8
9
0
MENU
PR
pullVOL
OK
VOL
PR
reception
is poor.
the 'Manual programme tuning' steps 1 to 3.
Press the Δ / Ε button to select Fine.
Press the Γ button.
Repeat
PR.
{
System
{
Channel
{
Fine
{
Search
{
Name
{
Booster
{
}{OOKOMENUOTV
4.
ProgrammeOedit
Station
Menu
tuning
Normally
2.
{
Repeat
Fine
1.
AutoOprogramme
ManualOprogramme
{{{{
AV
Press the Φ / Γ button to fine tune for the best picture and
sound on the Fine pull-down menu.
Press the OK button.
Press the TV/AV button to return to normal TV viewing.
The finely tuned programme will be indicated by yellow number
during programme selection.
11
Setting
Station
Menu
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
()O{OOKOMENUOTV
AV
{
TV
stations
up
Programme
edit
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
1.
2.
3.
the MENU button to select the Station menu.
Press the Γ button and then Δ
button to select
/ Ε
Programme edit.
Press the Γ button to display the Programme edit menu.
Repeatedly press
TV/AV
0O-O-O-O-O- OO 05O SO 6O9
1O CO 0O3OO06O SO 1O7
2O CO 1O2OO07O SO 2O2
1
2
3O SO 6O6OO08O CO 0O9
3
4O SO 6O7OO09O CO 1O1
4
5
6
DeleteOOOCopy
MoveOOOOOSkip
7
8
9
0
()O}{OOKOMENUOTV
Deleting
1.
2.
MENU
a
programme
Select a programme to be deleted with the Δ / Ε or Φ / Γ button.
Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one position.
PR
VOL
AV
0O-O-O-O-O- OO 05O SO 6O9
1O CO 0O3OO06O SO 1O7
VOL
2O CO 1O2OO07O SO 2O2
3O SO 6O6OO08O CO 0O9
4O SO 6O7OO09O CO 1O1
PR
Delete
MENUOTV
Copying
1.
2.
a
programme
Select a programme to be copied with the Δ / Ε
Press the GREEN button.
All the following programmes are shifted down
Moving
1.
2.
3.
AV
or Φ
one
/
Γ
button.
position.
a
programme
Select a programme to be moved with the Δ / Ε or Φ / Γ button.
Press the YELLOW button.
Move the programme to the desired programme number with
theΔ/ΕorΦ/Γbutton.
4.
Press the YELLOW button
0O-O-O-O-O-
again
to release this function.
O05O SO 6O9
1O CO 0O3OO06O SO 1O7
2O CO 1O2OO07O SO 2O2
3O SO 6O6OO08O CO 0O9
4O SO 6O7OO09O CO 1O1
MoveOOff
()O}{OMENUOTV
Skipping
1.
2.
3.
a
AV
programme number
programme number to be
Select a
skipped with the Δ / Ε or Φ / Γ
button.
Press the BLUE button. The skipped programme turns to blue.
Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be
unable to select it using the Δ / Ε button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
Press the TV/AV button to return to normal TV
12
viewing.
Setting
Calling
TV
stations
up
the programme table
check the programmes stored in the memory
the programme table.
You
can
Displaying programme
table
Press the LIST button to
display
the
Programme
by displaying
table
menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
0O-O-O-O-O-
O05O SO 6O9
TV/AV
1
2
3
4
5
6
7
8
9
1O CO 0O3OO06O SO 1O7
2O CO 1O2OO07O SO 2O2
3O SO 6O6OO08O CO 0O9
4O SO 6O7OO09O CO 1O1
0
()O}{OOKOMENUOTV
Note
a.
b.
AV
:
MENU
You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
PR
VOL
OK
VOL
PR
programme in the programme table
Select a programme with the Δ / Ε or Φ / Γ button.
Then press the OK button.
Selecting
a
The set switches to the chosen programme number.
programme table
10 programme table pages in which contain 100 pro-
Paging through
There
are
grammes.
Pressing the
Δ
/
a
Ε
or Φ
/
Γ
button
repeatedly
Press the TV/AV button to return to normal TV
LIST
turns the pages.
viewing.
13
Picture
Picture
Menu
CH.
PSM
{
User
{
100Hz
{
A u to
{
convergence
()O{OOKOMENUOTV
PSM
1.
2.
3.
adjustment
(Picture Status Memory)
the MENU button to select the Picture menu.
Press the Γ button and then Δ / Ε button to select PSM.
Press the Γ button and then Δ / Ε button to select a picture
setting on the PSM pull-down menu.
Repeatedly press
AV
CH.
PSM
{
Dynamic
User
{
Standard
100Hz
{
Mild
{
Game
A u to
convergence
TV/AV
User
()O}OOKOMENUOTV
4.
5.
PSM
AV
Press the OK or Φ button.
Press the TV/AV button to return to normal TV
You
viewing.
also recall a desired picture (Dynamic, Standard,
Mild, Game or User) with PSM button on the remote control. The
picture Dynamic, Standard, Mild and Game are programmed
for good picture reproduction at the factory and cannot be changed.
MENU
can
PR
VOL
OK
PR
VOL
Picture
You
adjust picture contrast, brightness, colour intensity, sharpand tint (NTSC AV only) to the levels you prefer.
can
ness
1.
2.
3.
adjustment
the MENU button to select the Picture menu.
Press the Γ button and then Δ / Ε button to select User.
Press the Γ button and then Δ / Ε button to select the desired
picture item on the User pull-down menu.
Repeatedly press
CH.
PSM
{
User
{
Contrast
{
100Hz
{
Brightness
{
Colour
{
Sharpness
{
A u to
convergence
()O}{O OKOMENUOTV
4.
5.
Press the
Press the
each sub
Γ
Φ
{
AV
button.
/ Γ button to make
appropriate adjustments
()O}{O OKOMENUOTV
14
the
menu.
Contrast
6.
7.
on
80
AV
You can also select other User items directly with Δ / Ε button
and adjust them with Φ / Γ button.
Press the OK button to store it for the picture User.
Press the TV/AV button to return to normal TV viewing.
Picture
adjustment
100Hz mode
CH.
When watching set, select desired
Mode 1 or Mode 2.
1.
2.
3.
condition
picture
by choosing
the MENU button to select the Picture menu.
Press the Γ button and then Δ / Ε button to select 100Hz.
Press the Γ button and then Δ / Ε button to select a picture
setting (Mode 1 or 2) on the 100Hz pull-down menu.
PSM
{
User
{
100Hz
{
A u to
convergence
Picture
Menu
{
Repeatedly press
()O{OOKOMENUOTV
AV
TV/AV
CH.
PSM
{
User
{
100Hz
{
Mode1
{
Mode2
A u to
convergence
()O}OOKOMENUOTV
4.
5.
AV
Press the OK or Φ button.
Press the TV/AV button to return to normal TV
Note : The 100Hz mode
COMPONENT 2 mode.
can
viewing.
MENU
not be selected in NTSC AV and
PR
VOL
Auto convergence
OK
VOL
PR
This function enables you to
adjust the colour convergence of
screen automatically during receiving the signals. When the set is
first installed or it is relocated, the picture may be unstable with
three colour ghosts (red, green, blue). This problem can be solved
by adjusting the colour convergence.
1. Repeatedly press the MENU button to select the Picture menu.
Γ
2.
Press the
3.
convergence.
Press the Γ button to
button and then
adjust
Δ
/
Ε
button to select Auto
the colour convergence
automatically.
Auto
Convergence
Position Checking
DATA
Note :
a.
The
operating point
green-red'.
b.
:
52
colour will
change
in the order of 'blue-
Please make sure the surrounding illumination where the TV is
situated remains dark otherwise the screen will become unstable or the message "The End" and "Ensure lights are
dimmed sufficiently" will be displayed on screen after Auto
convergence is completed. Auto convergence will then have to
be operated again.
15
Picture
adjustment
Picture format
watch TV in various picture formats; 16:9, Zoom1, Zoom2,
Auto, 4:3.
Repeatedly press the ARC button to select your desired picture format.
You
can
16:9
You can
enjoy the cinema (the picture format of 16:9) or general TV
programme through the 16:9 mode.
The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and right so that the screen 16:9 is full.
Zoom 1
You can enjoy the cinema in a vast screen through the Zoom mode.
The screen 4:3 is magnified to the upper / lower and left / right sides
so that the screen 16:9 is full. The bottom and top of the picture may
be lost. You can move the screen up or down with Δ / Ε button.
PICTURE
T
U
R
B
O
PR
Zoom 2
You can enjoy more magnified screen in this mode. The screen
Zoom 2 is viewed just like that but the screen 16:9 is magnified
more and more to the left and right so that the screen Zoom 2 is full.
Auto
When your set receives the wide screen signal, it will be automatically changed to the picture format to be sent.
PR
ARC
4:3
This
picture
Note
format is 4 to 3 of
general
TV.
In the double window, scan mode and COMPONENT 2
ARC function isn't available.
:
mode,
Turbo
picture
selection
When this function is on, picture will be more brilliant and distinct
picture than normal picture.
Repeatedly press the TURBO PICTURE button to switch on or off.
(Turbo Picture off)
16
(Turbo Picture on)
Sound
SSM
adjustment
(Sound Status Memory)
CH.
You can select your preferred sound setting; Dolby Virtual, Music,
Movie or Sports and you can also adjust the sound frequency of
SSM
{
Balance
{
AVL
{
Sound
Menu
equalizer.
1.
Repeatedly
2.
3.
press the MENU button to select the Sound menu.
Press the Γ button and then Δ / Ε button to select SSM.
Press the Γ button and then Δ / Ε button to select a sound setting on the SSM pull-down menu.
CH.
SSM
{
Dolby0Virtual
Balance
{
AVL
{
Music
Movie
()O{OOKOMENUOTV
AV
TV/AV
Sports
User
()O}{O OKOMENUOTV
{
AV
Dolby Virtual
Dolby Virtual lets you experience panoramic
Sound Frequency Adjustment
a. Press the Γ button in User to display the
effects of sound.
User sub
menu.
SOUND
MENU
T
U
R
B
O
0.1O0.5O1.5O5.0O10OkHz
PR
()O}{O OKOMENUOTV
AV
b. Select a sound band by pressing the Φ / Γ button.
c. Make appropriate sound level with the Δ / Ε button.
d. Press the OK button to store it for the sound User.
The display Stored appears.
Press the TV/AV button to return to normal TV viewing.
Sound
You
VOL
OK
VOL
PR
adjustment
adjust
matically keeps
can
balance
on an
AVL (Auto Volume Leveler). AVL autoequal volume level even if you change proor
grammes.
1.
2.
3.
4.
press the MENU button to select the Sound menu.
Press the Γ button and then Δ / Ε button to select the desired
sound item; Balance or AVL.
Make desired adjustment with the Φ / Γ, Δ / Ε or OK button
on each pull-down menu.
Press the TV/AV button to return to normal TV viewing.
Repeatedly
CH.
SSM
{
Balance
{
AVL
{
On
Off
()O}{O OKOMENUOTV
AV
Turbo sound selection
When this function is on, sound will be more emphasized and
amplified sound than normal.
Repeatedly press the TURBO SOUND button to switch on or off.
(Turbo Sound off)
Note
:
Turbo sound is not suitable for
(Turbo Sound on)
use
with
Dolby
Virtual.
17
Sound
adjustment
Sound output selection
In AV
mode, you
can
speakers.
select output sound for the left and
right
loud-
Repeatedly press the I/II button to select the sound output.
L+R :
Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loudspeaker.
L+L :
Audio signal from audio L input is sent to left and right loudspeakers.
R+R :
Audio signal from audio R input is sent to left and right loudspeakers.
Stereo/Dual
When
I/II
reception
programme is selected, the sound information for the station
appears after the programme number and station name disappear.
a
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II button twice again.
selection for dual language broadcast
If a programme received in two languages (dual language), you can
switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II but-
Language
ton
repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the loud-
speakers.
DUAL I+II sends
NICAM
a
separate language
to each
loudspeaker.
reception (option)
with the receiver for NICAM reception, the
high quality NICAM (Near Instantaneous Companding Audio
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
If your set is
1.
2.
3.
When NICAM mono is received, you can select NICAM
MONO or FM MONO.
When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
When NICAM dual is received, you can select NICAM DUAL
I, NICAM DUAL II or NICAM DUAL I+II or MONO. When
FM mono is selected the display MONO appears on the
screen.
18
equipped
Other functions
TV and AV modes
CH.
be set for TV or AV mode. AV mode is used when a video
cassette recorder (VCR), or other equipment is connected to the set.
Inputs
can
Note : When a VCR is connected via the aerial socket the set is
used in TV mode. See the 'Connection of external equipment' section.
Input
{
ChildOlock
{
AutoOsleep
{
BlueOback
{
()O{OOKOMENUOTV
Special
Menu
AV
TV/AV
1.
2.
3.
the MENU button to select the Special menu.
Press the Γ button and then Δ / Ε button to select Input.
Press the Γ button and then Δ / Ε button to select TV, AV1,
AV2, AV3, AV4, SAV4, COMPONENT 1, COMPONENT 2 on
Repeatedly press
CH.
Input
{
TV
ChildOlock
{
AutoOsleep
{
BlueOback
{
AV1
AV2
AV3
AV4
SAV4
COMPONENT1
COMPONENT2
()O}OOKOMENUOTV
1
2
3
4
5
6
7
8
9
0
MENU
AV
PR
4.
the Input pull-down menu.
AV 1 : VCR connected to the Euro scart socket 1 on the back
AV 2 : VCR connected to the Euro scart socket 2 on the back
AV 3 : VCR connected to the AV3 sockets of the set
AV 4 : VCR connected to the Euro scart socket 4 on the back
SAV4 : VCR connected to the Euro scart socket 4 on the back
COMPONENT 1 : COMPONENT connected to the COMPONENT 1 sockets on the back
COMPONENT 2 : COMPONENT connected to the COMPONENT 2 sockets on the back
Press the TV/AV button to return to normal TV viewing.
Alternatively you
can
select the TV
or
AV mode
by pressing
VOL
VOL
PR
the
TV/AV button.
In AV
mode, to return to TV mode, press the
Auto AV
Δ
/
Ε or
NUMBER buttons.
switching (option)
If your VCR outputs switching voltage when it is switched to playback with the VCR connected to the Euro scart socket. The set is
automatically switched to AV 1, AV 2 or AV 4 mode when an AV signal is input. But if you want to keep on watching TV mode, press the
/ Ε or NUMBER buttons.
Press the TV/AV button to return to AV modes.
Δ
19
Other functions
Special
Menu
CH.
Child lock
Input
{
ChildOlock
{
AutoOsleep
{
The TV
BlueOback
{
control it. This feature
can
be set
so
that the remote control handset is needed to
can
be used to
prevent unauthorized view-
ing.
1.
()O{OOKOMENUOTV
AV
2.
3.
4.
TV/AV
press the MENU button to select the Special menu.
Press the Γ button and then Δ / Ε button to select Child lock.
Press the Γ button and then Δ / Ε button to select On or Off
on the Child lock pull-down menu.
Press the TV/AV button to return to normal TV viewing.
Repeatedly
With the lock on, the display Child lock on appears on the screen
if any button on the front panel is pressed while viewing the TV.
Note : The
any button
Child lock on will not appear on the screen if
the front panel is pressed while displaying the
display
on
menus.
Auto
sleep
If you select On on the Auto sleep pull-down menu, the set will
automatically switch itself to standby mode approximately ten min-
MENU
utes after
PR
VOL
VOL
a
TV station
stops broadcasting.
press the MENU button to select the Special menu.
button and then Δ / Ε button to select Auto sleep.
button and then Δ / Ε button to select On or Off on
1.
Repeatedly
2.
Press the
Γ
3.
Press the
Γ
4.
the Auto sleep pull-down menu.
Press the TV/AV button to return to normal TV
PR
viewing.
Blue back
If you select On
on
the Blue back
ground
on
the
1.
SLEEP
2.
3.
4.
appears
screen
pull-down
when there is
menu, the blue backno or
poor
signal.
press the MENU button to select the Special menu.
Press the Γ button and then Δ /Ε button to select Blue back.
Press the Γ button and then Δ / Ε button to select On or Off on
the Blue back pull-down menu.
Press the TV/AV button to return to normal TV viewing.
Repeatedly
Note :
a.
The blue background automatically appears on the screen
when there is no signal in AV mode.
b.
The Blue back isn't suitable to use COMPONENT 2 mode.
Sleep
timer
You don't have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the
preset time elapses.
Press the SLEEP button to select the number of minutes. The dis-
0 will appear on the screen, followed by 10, 20, 30, 60, 90,
120, 180 and 240. The timer begins to count down from the number
of minutes selected.
play
Note :
a.
To view the remaining sleep time, press the SLEEP button once.
b.
To cancel the sleep time, repeatedly press the SLEEP button
until the display
0 appears.
c.
When you switch the set off, the set releases the preset sleep
time.
20
PIP
Option
PIP is
operation (option)
:
an
optional function,
so
that
set with PIP function can
only the
operate.
PIP
(Picture
in
Picture) displays
a
picture
within
a
picture.
On and off
Press the PIP button to switch on the sub
press this button again to switch it off.
mode selection for sub
Input
picture.
picture
Press the PIP INPUT button to select the
mode for the sub
input
picture.
Each time this button is pressed, each
ture is displayed as shown below.
Programme
number
COMPONENT2
Swapping
exchange
pic-
AV4
AV3
COMPONENT1
between main and sub
Press the PIP SWAP button to
mode for the sub
AV2
AV1
(option)
input
SAV4
pictures
the main and sub
pic-
tures.
Programme
selection for sub
picture
PIP
Press the PIP PR +/- buttons to select a programme for the sub picture. The selected programme number is displayed just below the
programme number of main picture.
Sub
picture
size
PIP PR
PIP INPUT
PIP SWAP
POSITION
Repeatedly press the SIZE button to select
size. The sub picture appears as below.
1/16 size of the main
PIP PR
picture
the desired sub
1/9 size
SCAN
STILL
SIZE
picture
1/2 size
Note : If broadcasting system of the main picture for PIP is differ
from sub picture's for PIP, the sub picture not be natural. (ex: In
case that main picture/sub picture is PAL/NTSC system)
Sub
picture
freeze
Press the STILL button to freeze motion of the sub
Press this button again to restore motion.
Sub
picture.
picture position change
Press the POSITION button repeatedly until desired
achieved. The sub pictures move clockwise.
Programme
position
is
scan
This function enables you to search all the stored stations on 12
sub pictures and see your favorite station by exchanging the main
and sub pictures.
Press the SCAN button repeatedly to select 12 sub pictures.
The selected sub pictures search all the stored stations
Press the SCAN button again to switch off sub pictures.
.
21
Teletext
(option)
Teletext (or TOP text) is an optional function, therefore only
with the teletext system can receive the teletext broadcast.
a
set
free service broadcast by most TV stations which gives
up-to-the-minute information on news, weather, television programmes, share prices and many other topics.
Teletext is
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods allowing quick and easy selection of teletext information.
TV/AV
1
2
3
4
5
6
7
8
9
a
Switch on/off
Press the TEXT button to switch to teletext.
The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are displayed
on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT or TV/AV button to switch off teletext. The previous
mode reappears.
0
PR
OK
SIMPLE text
PR
selection
Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number.
The Δ / Ε button can be used to select the preceding or following page.
Page
1.
TEXT
2.
M
colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
M
button to switch to LIST mode.
Programming
a
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control handset.
1.
Press
a
2.
Using
the NUMBER buttons, select the page you wish to pro-
3.
gramme.
Press the OK button. Then the selected page is stored as the
selected page number with blinking once. From now on, you
select this page with the same coloured button.
The three other coloured buttons are programmed in this way.
can
4.
22
coloured button.
Teletext
TOP text
(option)
(option)
The user guide displays four fields-red, green, yellow and blue at
the bottom of the screen. The yellow field denotes the next group
and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing
page with automatic overflow to the next group.
Alternatively the Δ button can be used.
4. The red button permits to return to previous selection.
Alternatively the Ε button can be used.
1
2
3
4
5
6
7
8
9
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
TOP mode.
0
PR
FASTEXT
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
selection
i
Press the
button to select the index page.
You can select the pages which are colour coded along the bottom line with the same coloured buttons.
Corresponding to the SIMPLE teletext mode, you can select a
page by entering its three digit page number with the NUMBER
buttons in FASTEXT mode.
The Δ / Ε button can be used to select the preceding or following page.
PR
Page
1.
2.
3.
4.
i
23
Teletext
Special
(option)
teletext functions
REVEAL
Press this button to
display concealed information, such as
solutions of riddles or puzzles.
Press this button again to remove the information from the
display.
SIZE
1
2
3
Selects double
4
5
6
Press
7
8
9
height text.
this button to enlarge the top
this button again to enlarge
Press
page.
Press this button
0
again
half of the page.
the bottom half of the
to return to the normal
display.
UPDATE
Displays
picture on
page. The display
teletext
PR
the TV
of the
corner
screen.
the
screen
while
waiting
for the
new
will appear at the top left hand
When the updated page is available then
will change to the page number.
Press this button to view the updated teletext page.
display
PR
HOLD
the automatic page
text page consists of 2 or
Stops
change
which will
occur
if
tele-
a
sub pages. The number of
sub pages and the sub page displayed is, usually, shown on
the screen below the time. When this button is pressed the
?
stop symbol is displayed
more
at the
top left-hand
of the
corner
and the automatic page change is inhibited.
To continue press this button again.
screen
MIX
Displays
the teletext pages
superimposed
on
the TV
pic-
ture.
To switch the TV
Note
:
picture
off press this button
When TV and text picture
are
again.
displayed half and half
of the screen, MIX function is not available.
TIME
TV programme, press this button to display
the time at the top right hand corner of the screen. Press this
When
viewing
button
again
a
to remove the
display.
In the teletext
mode,
press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or
the sub page, press the RED / GREEN,
NUMBER buttons.
change
Press
24
again
to exit this function.
Δ
/
Ε
or
Connection of external
You
connect additional
etc. to your set.
can
equipment,
such
as
equipment
VCRs, camcorders
Here shown may be somewhat different from your set.
Aerial socket
1.
2.
3.
4.
5.
Connect the RF out socket of the VCR to the aerial socket on
the back of the set.
Connect the aerial cable to the RF aerial in socket of the VCR.
Store the VCR channel on a desired programme number using
the 'Manual programme tuning' section.
Select the programme number where the VCR channel is
stored.
Press the PLAY button on the VCR.
COMPONENT1 COMPONENT2
(480i)
AV4
AUDIO
AV2
VIDEO
AV1
(480p)
(L)
(L)
(R)
(R)
Y
Y
PB
PB
PR
PR
AUDIO
VIDEO
ANT IN
LL
DVD INPUT
VCR
Euro scart socket
1.
2.
Connect the Euro scart socket of the VCR to the Euro scart
socket 1, 2, 4 of the set.
Press the PLAY button on the VCR.
If your VCR outputs a switching voltage connect to Euro scart
socket, the set will switch to AV 1, AV 2 or AV 4 mode automatically. But if you want to keep on watching TV mode, press the
Δ / Ε or NUMBER buttons.
Otherwise press the TV/AV button on the remote control handset
to select AV 1, AV 2 or AV 4. The VCR playback picture appears
on the screen.
You
Note
a.
b.
c.
d.
can
also record programmes received
by the TV on
COMPONENT1 COMPONENT2
(480i)
2.
3.
(R)
VIDEO
Y
Y
PB
PB
PR
PR
AUDIO
VIDEO
ANT IN
LL
DVD INPUT
VCR
video tape.
:
i.e. the signals red, green and blue can only
be selected for the Euro scart 1 and the AV 1 can be received.
These signals are transmitted, for example, by a pay TV
decoder, game machine or photo CD unit, etc.
If both Euro scart 1, 2 and 4 sockets have been connected to
the VCRs simultaneously, only the AV 2 can be received.
If S-VHS signal is received through the EURO scart socket 4,
you must change to the SAV4 mode.
In Euro scart 4 socket, the video output is not available.
Signal type RGB,
Audio/Video in sockets
1.
(L)
AUDIO (R)
AV2
AV1
(480p)
(L)
AV4
Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
Press the TV/AV button to select AV 3.
Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO (AV1 or AV3) socket of the set.
AV3
S-VIDEOL/MN
AUDIO
R
VCR
25
Connection of external
equipment
S-Video / Audio in sockets
AV3
When
connecting
picture quality will
S-VIDEOL/MN
1.
AUDIO
R
2.
S-VIDEO VCR
3.
4.
(S-AV)
S-VIDEO VCR to the S-VIDEO socket, the
be further improved.
an
Connect the S-video socket of the VCR to the S-VIDEO socket
of the set.
Connect the audio cable from the S-VIDEO VCR to the AUDIO
sockets of the set.
Select AV3 by pressing the TV/AV button repeatedly.
Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If both S-VIDEO and VIDEO sockets have been connected
to the S-VHS VCR simultaneously, only the S-VIDEO can be
received.
Component
1.
COMPONENT1 COMPONENT2
(480i)
(L)
(L)
AUDIO (R)
(R)
AV4
AV2
VIDEO
AV1
(480p)
Y
Y
PB
PB
PR
PR
AUDIO
VIDEO
2.
ANT IN
LL
DVD INPUT
in sockets
Connect the COMPONENT DVD output sockets (Y Cb Cr, Y Pb
Pr, Y B-Y R-Y or Y PB PR) of the COMPONENT to the COMPONENT 1 (480i)/COMPONENT 2 (480p) sockets (Y PB PR) of
the set.
Connect the audio cable from the COMPONENT to COMPONENT 1 (480i)/COMPONENT 2 (480p) AUDIO sockets of the
set.
3.
DVD
4.
Press the TV/AV button to select COMPONENT 1 or COMPONENT 2.
Press the PLAY button on the COMPONENT.
The COMPONENT playback picture appears on the screen.
Note :
a.
Even when DVD video input can be output, you will have only
see a black and white picture, but DVD audio input will not be
monitored.
b. Only COMPONENT 2 (480p) can receive vertical a Frequency
(60Hz) Progressive signal. If the picture is poor by connecting
the COMPONENT 2 (480p), connect the DVD to the COMPONENT 1 (480i).
26
Troubleshooting
check list
Symptoms
No
picture,
no
sound
Sound OK, poor
picture
Picture OK, poor sound
Picture blurred
Lines
or
streaks in
Poor
picture
reception
on some
channels
No colour
Poor colour
Remote control does not work
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched
Try
on
another channel
(weak signal)
Check aerial
(plugged
Check aerial
(broken lead?)
into
TV?)
Check aerial
Check for local interference
Adjust
contrast
Adjust brightness
Adjust
colour
Adjust
volume
Check the batteries in remote control
Check Audio/Video sockets
(VCR only)
27
GUARANTEE
LG Electronics U.K. Ltd. will
provide
the
following
services in order to
expedite
this
Guarantee.
1.
2.
All
faulty components
charge for a period of
which fail due to defective manufacture will be
12 months from the
date of
original
replaced
free of
purchase.
(or his service agent) who sold the product will be reimbursed for any
labour provided in the repair of this LG equipment, for a period of 12 months from the
original date of purchase. These claims must be made in accordance with the published scale of service charges and relevant claims procedure.
The dealer
PLEASE NOTE:
A.
B.
The dealer may restrict the guarantee to the original purchaser.
The dealer is not obliged to carry out service under guarantee if unauthorized modifimade to the apparatus, or if non standard components are used
serial number of the apparatus is removed, defaced, misused, or altered.
cations
C.
D.
are
if the
Any claims made under guarantee must be directed to the dealer from whom the
equipment was originally purchased. The dealer may, before carrying out service
under guarantee, require a receipted account as evidence of the date of purchase.
We respectfully point out that your dealer is not obligated to replace batteries if they
become exhausted
E.
or
Aerial
alignment
or worn
and
in
use.
consumer
control
adjustments
This guarantee does not affect your statutory
are
not covered
by
this guarantee.
rights.
REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT
MUST BE SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED.
Product
Registration Card:
It is
helpful to complete at least your name,
address, phone, model & serial numbers
and return it. This will enable LG to assist
you
in
receipt,
the future should you
your units be stolen,
lose your
or should
modifications be necessary.
To obtain information
or
assistance:
Call
0870
607
5544
Monday-Friday
9.00am-4.30pm.
Service website:
http://lgelectronics.co.uk
MODEL NO.*
*
Please
complete
for your
SERIAL NO.*
own
record
DATE OF PURCHASE
*
Download PDF