LG | RZ-15LA31 | LG RZ-15LA31 Owner’s Manual

LCD
Colour Television
OWNER'S MANUAL
Please read this manual
carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
on
the back cover and quote this inforrequire service.
mation to your dealer when you
Model number
:
Serial number
:
FOR THE GUARANTEE TERMS & CONDITIONS,
PLEASE REFER TO BACK COVER OF THIS MANUAL
P/NO
:
3828VA0335D
(ML012A, 061U TX)
(3840VA0024A/B, 3840VA0016C, 373-026F)
Contents
Installation
3
Location and function of controls
Remote control handset
Battery installation
Side panel
4
Basic operation
On and off / Programme selection
Volume adjustment / Quick view
Mute function / Auto Demonstration
On screen language selection (option)
7
On
8
screen menus
Menu selection
TV stations
Auto programme tuning
Manual programme tuning
Fine Tuning
Programme edit
Calling the programme table
9
Setting up
Picture adjustment
PSM (Picture Status
DRP (Digital Reality
Picture adjustment
14
Memory)
Picture)
Sound adjustment
SSM (Sound Status Memory)
Sound adjustment / Stereo/Dual reception
NICAM reception (option) / Sound output selection
15
Other functions
TV, AV and PC modes
Auto AV switching / Child lock
Auto sleep / Sleep timer
17
Teletext (option)
Switch on/off
SIMPLE text / TOP text (option)
FASTEXT / Special teletext functions
19
Connection of external equipment
Aerial socket
Euro scart socket
Audio/Video in sockets
S-Video/Audio in sockets (S-Video)
Headphone socket
22
Connection of PC
PC in socket (D-Sub
Menu selection
PC Setup
(option)
24
jack)
PIP operation
PIP operation / On and off
Input mode selection for sub picture
Programme selection for sub picture
Sub picture size
Sub picture position change
Troubleshooting
2
check list
27
29
Installation
Power
This set operates on a DC supply provided by the AC-DC adaptor, the
voltage is as indicated on the label on the back cover. Use only the
AC-DC adaptor supplied with the set and never apply an AC mains to
the set directly. The AC-DC adaptor operates on an AC mains supply,
the voltage is as indicated on the label of the AC-DC adaptor.
a.
Open the back panel cover.
b. Connect the DC plug of the AC-DC adaptor to the 12V socket of
the set.
c.
Connect the AC-DC adaptor and it's power cord.
d. Connect the power cord to an AC mains.
e.
Close the back panel cover.
In the event of thunderstorms or powercuts, please pull out the mains
plug of the AC-DC adaptor and the aerial plug. Do not allow anything
to rest upon or roll over the power cord, and do not place the set
where the power cord is subject to damage.
Warning
PR
VOL
OKMENU
TV IDEO
ON OF
PR
To prevent fire or shock hazard, do not expose the set to rain or
moisture. Do not rub or strike the Active Matrix LCD with anything
hard as this may scratch, mar, or damage the Active Matrix LCD
permanently.
Wiring (in
a
VOL
OK
ENU
TV IDEO
ON OF
U.K.
only)
This set is supplied with a BS 1363 approved 13 amp mains plug,
fused at 10 amp. When replacing the fuse always use a 10 amp BS
1362, BSI or ASTA approved type. Never use this plug with the fuse
cover omitted. To obtain a replacement fuse cover contact your
dealer or "LG Electronics U.K. Ltd."
If the type of plug supplied is not suitable for the mains sockets in
your home, then the plug should be removed and a suitable type fitted. Please refer to the wiring instructions below:
Warning (in
U.K.
c
b
d
only)
A mains
plug removed
destroyed. A mains plug
from the mains lead of this set must be
with bared wires is hazardous if inserted in
mains socket.
Do not connect either wire to the earth pin, marked with the letter E
or with the earth symbol
or coloured green or green and yellow.
If any other plug is fitted, use a 5 amp fuse, either in the plug, or at
the distribution board.
a
Important (in
U.K.
only)
The wires in this mains lead are coloured in accordance with the following codes:
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your
plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black. The wire which
is coloured brown must be connected to the terminal which is
marked with the letter L or coloured red.
Service
Never
remove
the back
cover
of the set as this can expose you to
the set does not operate proper-
high voltage and other hazards. If
ly, unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket marked +75 Ω on the back.
For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto
the screen. Care should be taken not to expose the set to any
unnecessary vibration, moisture, dust or heat. Also ensure that the
set is placed in a position to allow a free flow of air. Do not cover
the ventilation openings on the back cover.
This standing angle can be adjusted as shown in pictures.
Cleaning
Unplug the set before cleaning the face of the LCD Screen. Dust
the set by wiping the screen and the cabinet with a soft, clean cloth.
If the screen requires additional cleaning, use a clean, damp cloth.
Do not use liquid cleaners or aerosol cleaners.
3
Location and function of controls
All the functions
can
be controlled with the remote control handset.
Some functions
can
also be
panel
adjusted
with the buttons
on
the side
of the set.
Remote control handset
POWER
MUTE
1
1
2
3
Before you use the remote control
teries. See the next page.
1.
POWER
switches the set
2
4
5
6
7
8
9
2.
0
i
PR-
4
PR+
VOL
or
4.
LIST/
INPUT
PR
on
from
standby
and selects
a
programme.
MENU
(or INDEX)
selects
a menu.
selects
an
index page in the teletext mode
(only
TELETEXT
Δ / Ε (Programme Up/Down)
selects a programme or a menu item.
switches the set
on from standby.
(Volume Up/Down)
adjusts the volume.
adjusts menu settings.
Φ
TEXT/MIX
SIZE
HOLD
POSITION
TIME
REVEAL
I/II
PIP
SLEEP
/
Γ
OK
accepts your selection
or
displays
the current mode.
M
PSM
SSM
5.
8
Q.VIEW
returns to the
6.
For further
7.
previously
TELETEXT BUTTONS
These buttons
are
details,
viewed programme.
(option)
used for teletext.
see
the 'Teletext' section.
I/II
selects the
language during dual language
output (option).
selects the sound
8.
PSM
(Picture Status Memory)
preferred picture setting.
recalls your
9.
4
standby.
VOL
OK
7
9
off to
standby
models).
5
6
from
NUMBER BUTTONS
switches the set
3.
PR
Q.VIEW
on
TV/AV/PC
MENU/INDEX
3
handset, please install the bat-
SSM (Sound Status Memory)
recalls your preferred sound setting.
broadcast.
Location and function of controls
10. MUTE
switches the sound
off.
on or
11. TV/AV/PC
selects
TV, AV
clears the
PC monitor mode.
or
menu
switches the set
from the
from
on
screen.
standby.
POWER
12. PIP BUTTONS
(option) (PC
mode
MUTE
only)
10
PIP
switches the sub
picture
on or
off.
1
2
3
4
5
6
7
8
PR +/selects
a
programme for the sub
picture.
INPUT
selects the
input
mode for the sub
picture.
POSITION
9
TV/AV/PC
MENU/INDEX
relocates the sub
in
picture
up/down
or
left/right
0
i
direction.
11
12
13. LIST
PR-
displays
PR+
PR
the programme table.
VOL
VOL
OK
14. SLEEP
sets the
Note
:
sleep
In teletext
Q.VIEW
timer.
13
mode, the PR+/-, Q.VIEW and LIST buttons
are
used for teletext functions.
Battery
LIST/
INPUT
PR
installation
TEXT/MIX
SIZE
HOLD
POSITION
TIME
REVEAL
I/II
PIP
SLEEP
M
The remote control handset is
To load the
batteries,
powered by
two AAA
type
turn the remote control handset
batteries.
over
PSM
12
14
SSM
and
open the battery compartment. Install two batteries as indicated by
the polarity symbols ( + and
) marked inside the compartment.
12
-
Note
:
To avoid
damage
from
batteries if you do not plan to
extended
period
possible battery leakage,
use
remove
the
the remote control handset for
an
of time.
5
Location and function of controls
Side
panel
7
PR
6
VOL
5
OK
4
Back
MENUTV/APC
3
ON/ F
1
H/P
panel
AV2
S-VIDEO
VIDEO
2
(MONO)
L
AUDIO
R
8
1.
MAIN POWER
(ON/OFF)
switches the set
on or
7.
off.
9
10
POWER/STANDBY INDICATOR
illuminates
brightly
( )
when the set is in
standby
mode.
2.
TV/AV/PC
selects
dims when the set is switched
TV, AV
clears the
or
menu
switches the set
3.
from the
on
from
screen.
8.
REMOTE CONTROL SENSOR
9.
HEADPHONE SOCKET
standby.
MENU
Connect the
selects
headphone plug
to this socket.
a menu.
10. AUDIO/VIDEO IN SOCKETS
4.
on.
PC monitor mode.
OK
(AV2)
Connect the audio/video out sockets of exter-
accepts your selection
or
displays
the current
mode.
nal
equipment
to these sockets.
S-VIDEO/AUDIO IN SOCKETS
5.
Φ
/ Γ
(Volume Up/Down)
adjusts the volume.
adjusts menu settings.
Connect the video out socket of
(S-Video)
an
Connects the audio out sockets of the SVIDEO VCR to the audio sockets
6.
Δ
/
Ε
(Programme Up/Down)
selects
a programme or a menu item.
switches the set on from standby.
6
S-VIDEO
VCR to the S-VIDEO socket.
as
in AV2.
Basic
operation
On and off
1.
2.
3.
4.
Press the main power button to switch the set on.
If the set is in standby mode, press the POWER, Δ / Ε,
TV/AV/PC or NUMBER buttons on the remote control handset
to switch it on fully.
Press the POWER button on the remote control handset.
The set reverts to standby mode.
Press the main power button again to switch the set off.
Note : If, while the set is switched on, the mains plug is disconnected the set will switch to standby or power on when the mains
plug is replaced in the mains power socket.
Programme
selection
You can select
buttons.
a
Volume
Press the
programme number with the
Δ
/
Ε
or
/
Γ
button to
MUTE
1
2
3
4
5
6
7
8
NUMBER
adjustment
Φ
POWER
9
TV/AV/PC
MENU/INDEX
adjust
the volume.
0
Quick view
PR
Press the Q.VIEW button to view the last programme you
were
watching.
VOL
Q.VIEW
Mute function
Press the MUTE button. The sound is switched off and the
VOL
OK
PR
display
W appears.
You
can
cancel it
by pressing
the
MUTE,
Φ
/ Γ,
SSM, I/II button.
I/II
Auto Demonstration
To review all the
programmed in the set, press the OK butpanel control for about 10 seconds. To stop auto
demonstration, press any button of the side panel control and
POWER button of the remote control.
menus
SSM
ton of the side
On
screen
language
selection
The menu can be displayed
First select your language.
on
the
(option)
screen
in desired
language.
1.
2.
3.
Press the MENU button to select the Station menu.
Press the Γ button and then Δ / Ε button to select Language.
Press the Γ button and then Δ / Ε button to select your desired
4.
All the on screen displays will appear in the selected language.
Press the OK or Φ button to select the Station menu.
Press the TV/AV/PC button to return to normal TV viewing.
language.
7
On
screen menus
Menu selection
press the MENU button to display each menu.
button and then Δ / Ε button to select a menu item.
Γ button to
display the sub menu or the pull-down
1.
Repeatedly
2.
Press the
Press the
3.
Γ
menu.
4.
Change
the
setting
of
an
item in the sub
or
pull-down
menu
with
Φ/ΓorΔ/Ε.
You
Φ
Γ
1
2
3
4
5
6
7
8
9
can move
to the
button and to
button.
higher
move
menu
by pressing the OK or
menu by pressing the
Note :
a.
In the AV/PC mode, the Station menu is not displayed.
b. In the teletext mode, menus are not displayed.
c.
On some models, the Language will not display.
MENU/INDEX
Station
0
level
to the lower level
CH.
Station
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
Language
{
{
{
System
StorageOfrom
{
Start
{
{
OBG
OI
ODK
OL
PR
VOL
OK
VOL
()O{OOKOMENU
Station
()O}{OOKOMENU
menu
PR
Picture
CH.
Station
PSM
{
DRP
User
{
O1
{
Storage
System
{
OO
{
Channel
{
Fine
{
Search
{
Name
{
()O{OOKOMENU
M
Picture
()O}{OOKOMENU
menu
Station
Sound
CH.
SSM
{
00O-O-O-O-O- O05O SO 6O9
Balance
{
01O CO 0O3OO06O SO 1O7
AVL
{
02O CO 1O2OO07O SO 2O2
03O SO 6O6OO08O CO 0O9
04O SO 6O7OO09O CO 1O1
DeleteOOOOCopy
MoveOOOOOOSkip
()O{OOKOMENU
Sound
()O}{O OKOMENU
menu
Special
CH.
Input
{
ChildOlock
{
AutoOsleep
{
()O{OOKOMENU
Special
TV programme
8
menu
Setting up
TV stations
Up to 100 TV stations can be stored by programme numbers (0 to 99).
Once you have preset the stations, you will be able to use the Δ / Ε
or NUMBER buttons to scan the stations you have programmed.
Stations can be tuned using automatic or manual modes.
Auto programme
Station
Menu
Station
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
{
tuning
()O{OOKOMENU
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.
1.
Repeatedly
2.
Press the
Γ
press the MENU button to select the Station menu.
button and then Δ / Ε button to select Auto pro-
gramme.
3.
Press the
Γ
button to
display
the Auto programme
menu.
Station
System
StorageOfrom
{
Start
{
{
OBG
OI
ODK
OL
1
2
3
4
5
6
7
8
9
TV/AV/PC
MENU/INDEX
()O}{OOKOMENU
0
Press the Γ button. Select a TV system with the Δ / Ε button
on the System pull-down menu;
L
: SECAM L/L' (France)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
5.
Press the OK or Φ button.
6.
Press the Δ / Ε button to select Storage from.
7.
Press the Γ button. Select the beginning programme number
with the Φ / Γ button or NUMBER buttons on the Storage
from pull-down menu. Any number under 10 is entered with a
numeric '0' in front of it, i.e. '05' for 5.
8.
Press the OK button.
9.
Press the Δ / Ε button to select Start.
10. Press the Γ button to begin auto programming.
4.
PR
VOL
OK
VOL
PR
M
Station
System
StorageOfrom
{
Start
{
{
OOC O01O(BG)
77O7O7O36%
MENU
All receivable stations are stored. The station name is stored for
stations which broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data. If no
station name can be assigned to a station, the channel number
is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47),
followed by a number.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the 'Programme edit' section
to edit the stored programme.
11. Press the TV/AV/PC button to return to normal TV
viewing.
9
TV stations
Setting up
Station
Menu
Station
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
()O{OOKOMENU
{
Manual programme
tuning
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
name with five characters to each programme number.
1.
Repeatedly
2.
Press the
Γ
press the MENU button to select the Station menu.
button and then Δ / Ε button to select Manual
programme.
3.
Press the
Γ
button to
display
the Manual programme
menu.
Station
1
2
3
4
5
6
7
8
9
TV/AV/PC
MENU/INDEX
Storage
System
{
O1
{
OO
Channel
{
Fine
{
Search
{
Name
{
()O}{O OKOMENU
4.
5.
Press the
Press the
/ Ε button to select Storage.
button to select the programme number. Select the
Δ
Γ
desired programme number (0 to 99) with the Φ / Γ button or
NUMBER buttons on the Storage pull-down menu. Any num-
0
ber under 10 is entered with
VOL
OK
a
numeric '0' in front of
it, i.e. '05'
for 5.
PR
6.
VOL
7.
8.
Press the OK button.
Press the Δ / Ε button to select
Press the Γ button. Select a TV
System.
system with the
Δ
/ Ε button
the System pull-down menu;
L
: SECAM L/L' (France)
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
Press the OK or Φ button.
on
PR
9.
M
10. Press the
Δ
11. Press the
Γ
or
If
Cable
the Channel pull-down
select the channel number
on
possible,
Any
buttons.
front of
/ Ε button to select Channel.
button. Press the Δ / Ε button to select
directly
number under 10 is entered with
it, i.e. '05' for
with the number
a
numeric '0' in
5.
12. Press the OK
or Φ
13. Press the
button to select Search.
button. Press the Φ / Γ button to
14. Press the
Δ
Γ
/
V/UHF
menu.
button.
Ε
commence
the Search pull-down menu. If a station is found
the search will stop.
15. Press the OK button to store it. The display Stored will appear.
searching
on
Station
Storage
System
{
Channel
{
Fine
{
Search
{
Name
{
{
{{{{
Stored
16. To store another
station, repeat steps
4 to 15.
17. Press the TV/AV/PC button to return to normal TV
10
viewing.
Setting up
Assigning a station name
1.
Repeat the 'Manual programme tuning' steps
2.
Press the
Δ
3.
Press the
Γ
/ Ε button to select Name.
button on the Name pull-down
4.
Press the Δ button. You
and the alphabet A to Z.
can use a
blank,
TV stations
CH.
menu.
With the
Ε button
you can select in the opposite direction.
Select the position by pressing the Φ / Γ button and then make
your choice of the second character, and so on.
6.
Press the OK button.
7.
Press the TV/AV/PC button to return to normal TV
fine
is
only
necessary if
reception
the 'Manual programme tuning'
Δ / Ε button to select Fine.
Γ button.
1.
Repeat
2.
Press the
Press the
3.
tuning
{
ProgrammeOedit
{
Language
{
{
steps
()O{OOKOMENU
viewing.
tuning
Normally
AutoOprogramme
ManualOprogramme
+, -, the numeric 0 to 9
5.
Fine
Station
Menu
Station
1 to 3.
is poor.
1 to 3.
1
2
3
4
5
6
7
8
9
TV/AV/PC
MENU/INDEX
0
Station
Storage
System
{
Channel
{
Fine
{
Search
{
Name
{
PR
{
{{{{
VOL
Press the
sound
5.
6.
Φ
/
Γ
button to fine tune for the best
the Fine pull-down
Press the OK button.
on
ber
picture
and
menu.
Press the TV/AV/PC button to return to normal TV
The
VOL
PR
}{OOKOMENU
4.
OK
finely tuned programme will be
during programme selection.
indicated
by
a
viewing.
yellow numM
11
Setting up
Station
Menu
Station
CH.
AutoOprogramme
ManualOprogramme
{
ProgrammeOedit
{
Language
{
{
Programme
edit
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
1.
2.
()O{OOKOMENU
TV stations
3.
press the MENU button to select the Station menu.
Press the Γ button and then Δ / Ε button to select Programme
edit.
Press the Γ button to display the Programme edit menu.
Repeatedly
00O-O-O-O-O- OO05O SO 6O
9
01O CO 0O
3OO06O SO 1O
7
02O CO 1O
2OO07O SO 2O
2
03O SO 6O
6OO08O CO 0O
9
04O SO 6O
7OO09O CO 1O1
DeleteOOOCopy
MoveOOOOOSkip
1
2
3
4
5
6
7
8
()O}{O OKOMENU
Deleting
1.
2.
9
TV/AV/PC
MENU/INDEX
a programme
Select a programme to be deleted with the Δ / Ε or Φ / Γ button.
Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one position.
0
00O-O-O-O-O- OO05O SO 6O
9
01O CO 0O
3OO06O SO 1O
7
02O CO 1O
2OO07O SO 2O
2
03O SO 6O
6OO08O CO 0O
9
04O SO 6O
7OO09O CO 1O1
PR
VOL
OK
Delete
VOL
MENU
PR
Copying
1.
2.
a programme
Select a programme to be copied with the Δ / Ε
Press the GREEN button.
All the following programmes are shifted down
Moving
M
1.
2.
3.
or Φ
one
/
Γ
button.
position.
a
programme
Select a programme to be moved with the Δ / Ε or Φ / Γ button.
Press the YELLOW button.
Move the programme to the desired programme number with
theΔ/ΕorΦ/Γbutton.
4.
Press the YELLOW button
again
to release this function.
00O-O-O-O-O- OO05O SO 6O9
01O CO 0O
3OO06O SO 1O
7
02O CO 1O
2OO07O SO 2O
2
03O SO 6O
6OO08O CO 0O
9
04O SO 6O
7OO09O CO 1O1
MoveOOff
()O}{O MENU
a programme number
Select a programme number to be skipped with the Δ / Ε or Φ / Γ
button.
Press the BLUE button. The skipped programme turns to blue.
Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be
unable to select it using the Δ / Ε button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
Skipping
1.
2.
3.
Press the TV/AV/PC button to return to normal TV
12
viewing.
Setting up
TV stations
the programme table
Calling
You can check the programmes stored in the memory
the programme table.
Displaying programme table
Press the LIST button to display
the
by displaying
Programme table
menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
00O-O-O-O-O- OO05O SO 6O9
01O CO 0O
3OO06O SO 1O
7
02O CO 1O
2OO07O SO 2O
2
03O SO 6O
6OO08O CO 0O
9
04O SO 6O
7OO09O CO 1O1
()O}{OOKOMENU
Note
:
a.
You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
b.
Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
1
2
3
4
5
6
7
8
9
TV/AV/PC
0
PR
programme in the programme table
programme with the Δ / Ε or Φ / Γ button.
Selecting
Select
a
a
Then press the OK button.
The set switches to the chosen programme number.
Paging through
There
are
a
VOL
OK
VOL
LIST/
INPUT
PR
programme table
10 programme table pages in which contain 100 pro-
grammes.
Pressing the
Δ
/
Ε
or Φ
/
Γ
button
repeatedly
turns the pages.
M
Press the TV/AV/PC button to return to normal TV
viewing.
13
Picture
Picture
Menu
Picture
CH.
PSM
{
DRP
{
User
{
adjustment
PSM (Picture Status Memory)
1.
Repeatedly press the MENU button
Press the
Press the
2.
3.
setting
on
to select the Picture menu.
button and then Δ / Ε button to select PSM.
Γ button and then Δ / Ε button to select a
picture
the PSM pull-down menu.
Γ
Picture
()O{OOKOMENU
CH.
PSM
{
Dynamic
DRP
{
Standard
User
{
Mild
Game
User
()O}OOKOMENU
Press the OK or Φ button.
Press the TV/AV/PC button to return to normal TV
4.
5.
1
2
3
4
5
6
7
8
9
TV/AV/PC
MENU/INDEX
0
OK
DRP
(Digital Reality Picture)
DRP
1.
2.
3.
PR
VOL
viewing.
You can also recall a desired picture (Dynamic, Standard, Mild,
Game or User) with PSM button on the remote control. The picture
Dynamic, Standard, Mild and Game are programmed for optimum picture reproduction at the factory and cannot be changed.
improves image outlines in dark screens.
Repeatedly press the MENU button to select
VOL
4.
5.
PR
the Picture menu.
Press the Γ button and then Δ / Ε button to select DRP.
Press the Γ button and then Δ / Ε button to select Dynamic
or Mild on the DRP pull-down menu.
Press the OK or Φ button.
Press the TV/AV/PC button to return to normal TV viewing.
Picture
You
adjustment
adjust picture contrast, brightness, colour intensity, sharpness and tint (NTSC AV only) to the levels you prefer.
1.
Repeatedly press the MENU button to select the Picture menu.
2.
can
Press the
Γ
button and then
Δ
/
Ε
button to select User.
Picture
M
CH.
PSM
PSM
{
DRP
{
User
{
Contrast
{
Brightness
{
Colour
{
Sharpness
{
Tint
{
()O}{O OKOMENU
3.
Press the Γ button and then Δ / Ε button to select the desired
item on the User pull-down menu.
Press the Γ button.
picture
4.
Contrast
80
()O}{O OKOMENU
5.
6.
7.
14
Press the Φ / Γ button to make appropriate adjustments on the
each sub menu.
You can also select other User items directly with Δ / Ε button
and adjust them with Φ / Γ button.
Press the OK button to store it for the picture User.
Press the TV/AV/PC button to return to normal TV viewing.
Sound
SSM
You
(Sound Status Memory)
Sound
Menu
Sound
select your preferred sound setting; Flat, Music, Movie or
and you can also adjust the sound frequency of the equalizer.
can
Speech
1.
2.
3.
adjustment
press the MENU button to select the Sound menu.
Press the Γ button and then Δ / Ε button to select SSM.
Press the Γ button and then Δ / Ε button to select a sound setting on the SSM pull-down menu.
CH.
SSM
{
Balance
{
AVL
{
Repeatedly
()O{OOKOMENU
Sound
CH.
SSM
{
Balance
{
AVL
{
Flat
Music
Movie
Speech
User
{
()O}OOKOMENU
Sound Frequency Adjustment
a. Press the Γ button in User to
display
the User sub
menu.
0.1O0.5O1.5O5.0O10OkHz
1
2
3
4
5
6
7
8
9
TV/AV/PC
MENU/INDEX
()O}{O OKOMENU
0
b. Select a sound band by pressing the Φ / Γ button.
c. Make appropriate sound level with the Δ / Ε button.
d. Press the OK button to store it for the sound User.
The display Stored appears.
Press the TV/AV/PC button to return to normal TV
viewing.
You
can also recall a desired sound setting (Flat, Music, Movie,
Speech or User) with SSM button on the remote control. The sound
settings Flat, Music, Movie and Speech are programmed for optimum sound reproduction at the factory and cannot be changed.
PR
VOL
VOL
OK
PR
If you press the SSM button after making appropriate adjustthe User sub menu, the display User automatically
appears even though you have already set a factory preset setting;
Flat, Music, Movie or Speech.
Note
ment
:
on
M
Sound
adjustment
You
can adjust balance, AVL (Auto
ically keeps on an equal volume
SSM
Volume Leveler). AVL automatlevel even if you change pro-
grammes.
1.
2.
3.
press the MENU button to select the Sound menu.
Press the Γ button and then Δ / Ε button to select the desired
sound item; Balance or AVL.
Make desired adjustment with the Φ / Γ, Δ / Ε or OK button
on each pull-down menu.
Repeatedly
Sound
CH.
SSM
{
Balance
{
AVL
{
On
Off
()O}OOKOMENU
4.
Press the TV/AV/PC button to return to normal TV
viewing.
15
Sound
adjustment
Stereo/Dual
reception
When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
Mono sound selection
In stereo reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II button twice again.
for dual language broadcast
programme is received in two languages (dual language), you
can switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II
button repeatedly.
DUAL I sends the primary broadcast language to the loudspeakers.
DUAL II sends the secondary broadcast language to the loud-
Language selection
If
a
speakers.
DUAL I+II sends
NICAM
a
separate language
to each
loudspeaker.
reception (option)
If your set is
equipped with the receiver for NICAM reception, the
high quality NICAM (Near Instantaneous Companding Audio
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
When NICAM mono is received, you can select NICAM
MONO or FM MONO.
When NICAM stereo is received, you can select NICAM
STEREO or FM MONO. If the stereo signal is weak, switch to
FM mono.
When NICAM dual is received, you can select NICAM DUAL
I, NICAM DUAL II or NICAM DUAL I+II or MONO. When
FM mono is selected the display MONO appears on the
1.
I/II
2.
3.
screen.
Sound output selection
In AV
mode, you
can
select
output sound for the left and right loud-
speakers.
press the I/II button to select the sound output.
Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loud-
Repeatedly
L+R
:
L+L
:
R+R
16
:
speaker.
Audio signal
speakers.
Audio signal
speakers.
from audio L
input
is sent to left and
right
loud-
from audio R
input
is sent to left and
right
loud-
Other functions
TV, AV and PC modes
Inputs
can
be set for
TV,
video cassette recorder
AV
Special
Special
or
(VCR),
PC mode. AV mode is used when
or
other
equipment
CH.
a
is connected to
Input
{
ChildOlock
{
AutoOsleep
{
Menu
the set.
Note : When a VCR is connected via the aerial socket the set is used
in TV mode. See the 'Connection of external equipment' section.
press the MENU button to select the Special menu.
button and then Δ / Ε button to select Input.
Press the Γ button and then Δ / Ε button to select TV, AV 1,
1.
Repeatedly
2.
Press the
3.
()O{OOKOMENU
AV
Γ
2, S-Video
or
PC.
Special
CH.
Input
{
TV
ChildOlock
{
AV1
AutoOsleep
{
AV2
1
2
3
4
5
6
7
8
S_Video
PC
()O}OOKOMENU
The three AV and PC modes
AV 1
4.
:
are :
0
VCR connected to the Euro scart socket of the set
AV2:VCRconnectedtotheAV2oftheset
S-Video : S-VIDEO VCR connected to the S-VIDEO socket of
the set
PC
: PERSONAL COMPUTER connected to the PC socket
of the set
Press the TV/AV/PC button to return to normal TV viewing.
you can select the TV
TV/AV/PC button.
Alternatively
In AV
9
TV/AV/PC
MENU/INDEX
mode,
to return to TV
or
AV mode
mode, press the
Δ
/
by pressing
Ε or
PR
VOL
OK
VOL
PR
the
NUMBER but-
tons.
Auto AV
switching
M
If your VCR outputs an AV switching signal via the Scart lead the
set will auto switch to AV 1 mode on start of playback, but if you
want to keep on watching in TV mode, press the Δ / Ε or NUMBER
buttons. Press the TV/AV/PC button to return to AV modes.
Child lock
The TV
can
be set
so
control it. This feature
1.
2.
3.
4.
that the remote control handset is needed to
can
be used to
prevent unauthorized viewing.
Repeatedly press the MENU button to select the Special menu.
Press the Γ button and then Δ / Ε button to select Child lock.
Press the Γ button and then Δ / Ε button to select On or Off on
the Child lock pull-down menu.
Press the TV/AV/PC button to return to normal TV viewing.
With the lock on, the display Child lock on appears on the screen
if any button on the front panel is pressed while viewing the TV.
Note : The display Child lock on will not appear on the screen if
any button on the front panel is pressed while displaying the menus.
17
Other functions
Auto
Special
Special
Menu
CH.
Input
{
ChildOlock
{
AutoOsleep
{
sleep
If you select On on the Auto sleep pull-down menu, the set will
switch itself to standby mode approximately ten min-
automatically
utes after
()O{OOKOMENU
a
TV station
stops broadcasting.
press the MENU button to select the Special menu.
button and then Δ / Ε button to select Auto sleep.
1.
Repeatedly
2.
Press the
3.
Press the Γ button and then Δ / Ε button to select On or Off
the Auto sleep pull-down menu.
Press the TV/AV/PC button to return to normal TV viewing.
4.
Sleep
Γ
on
timer
1
2
3
4
5
6
7
8
9
Press the SLEEP button to select the number of minutes. The dis-
TV/AV/PC
will appear on the screen, followed by 10, 20, 30, 60, 90,
play
120, 180 and 240. The timer begins to count down from the number
You don't have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the
MENU/INDEX
0
preset time elapses.
---
of minutes selected.
PR
Note :
To view the remaining sleep time, press the SLEEP button once.
b.
To cancel the sleep time, repeatedly press the SLEEP button
until the display
appears.
c.
When you switch the set off, the set releases the preset sleep time.
a.
VOL
OK
VOL
---
PR
SLEEP
18
Teletext
(option)
Teletext (or TOP text) is an optional function, therefore only
with the teletext system can receive the teletext broadcast.
Teletext is
a
set
free service broadcast by most TV stations which gives
information on news, weather, television programmes, share prices and many other topics.
a
up-to-the-minute
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods allowing quick and easy selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext. The initial page or last
page appears on the screen.
Two page numbers, TV station name, date and time are displayed
on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TV/AV/PC button to switch off teletext. The previous
mode reappears.
1
2
3
4
5
6
7
8
0
SIMPLE text
PR
Page selection
1.
2.
OK
Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number.
The Δ / Ε button can be used to select the preceding or fol-
lowing
9
TV/AV/PC
PR
TEXT
page.
a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT
M
button to switch to LIST mode.
Programming
mode, press theM
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control handset.
1.
Press
a
2.
Using
the NUMBER
3.
gramme.
Press the OK button. Then the selected page is stored as the
selected page number by blinking once. From now on, you can
4.
coloured button.
buttons, select the page you wish
to pro-
select this page with the same coloured button.
The three other coloured buttons are programmed in this way.
Note
:
In PIP of the PC
mode, select the sub picture size is PIP (S),
PIP
(M) or PIP (L).
In PIP (S) of the PC mode,
the text
on
the
screen
may be unstable.
19
Teletext
TOP text
(option)
(option)
The user guide displays four fields-red, green, yellow and blue at
the bottom of the screen. The yellow field denotes the next group
and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2.
Use the yellow button to proceed to the next group with automatic overflow to the next block.
3. With the green button you can proceed to the next existing
page with automatic overflow to the next group.
Alternatively the Δ button can be used.
4. The red button permits to return to previous selection.
Alternatively the Ε button can be used.
1
2
3
4
5
6
7
8
9
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
TOP mode.
MENU/INDEX
i
0
FASTEXT
PR
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
Page selection
PR
1.
2.
3.
4.
i
Press the
button to select the index page.
You can select the pages which are colour coded along the bottom line with the same coloured buttons.
Corresponding to the SIMPLE teletext mode, you can select a
page by entering its three digit page number with the NUMBER
buttons in FASTEXT mode.
The Δ / Ε button can be used to select the preceding or fol-
lowing
20
page.
Teletext
Special
(option)
teletext functions
REVEAL
Press this button to
display concealed information, such as
puzzles.
again to remove the information from the
solutions of riddles
Press this button
or
display.
SIZE
Selects double
height text.
enlarge the top
button again to enlarge
Press this button to
Press this
page.
Press this button
again
half of the page.
the bottom half of the
to return to the normal
display.
UPDATE
Displays the
teletext
TV
picture on
page. The display
of the
corner
screen.
the
screen
When the
while
waiting
for the
1
2
3
4
5
6
7
8
9
new
will appear at the top left hand
is available then
0
updated page
will change to the page number.
Press this button to view the updated teletext page.
display
PR
HOLD
Stops
the automatic page
text page consists of 2
change
which will
occur
if
a
tele-
sub pages. The number of
sub pages and the sub page displayed is, usually, shown on
the screen below the time. When this button is pressed the
PR
or more
stop symbol is displayed
at the
top left-hand
corner
of the
and the automatic page change is inhibited.
To continue press this button again.
screen
MIX
SIZE
HOLD
TIME
REVEAL
MIX
Displays
the teletext pages superimposed on the TV
picture off press this button again.
picture.
To switch the TV
TIME
When
viewing
the time at the
button
again
a
TV programme, press this button to display
corner of the screen. Press this
top right hand
to
remove
the
display.
In the teletext
mode,
press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or
the sub page, press the
NUMBER buttons.
change
Press
again
RED/GREEN,
Δ
/
Ε
or
to exit this function.
21
Connection of external
You
connect additional
can
etc. to your set.
Examples
equipment
equipment,
are
such
VCRs, camcorders
as
shown below.
Aerial socket
1.
Connect the RF out socket of the VCR to the aerial socket of
2.
the set.
Connect the aerial cable to the RF aerial in socket of the VCR.
3.
VCR
4.
5.
Store the VCR channel on a desired programme number using
the 'Manual programme tuning' section.
Select the programme number where the VCR channel is
stored.
Press the PLAY button
on
the VCR.
Euro scart socket
1.
Connect the Euro scart socket of the VCR to the Euro scart
2.
socket of the set.
Press the PLAY button
on
the VCR.
If your VCR outputs an AV switching signal via the Scart lead the
set will auto switch to AV 1 mode on start of playback, but if you
want to
keep
on
watching
in TV
mode, press the
Δ
/
Ε
or
NUM-
BER buttons.
VCR
Otherwise press the TV/AV/PC button on the remote control
handset to select AV 1. The VCR playback picture appears on
the
You
screen.
can
also record programmes received
by
the TV
on
video
tape.
Note
:
Use the Euro scart cable socket
connect it to the set
length
is 5.5cm under to
correctly.
Audio/Video in sockets
1.
Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
2.
3.
Press the TV/AV/PC button to select AV 2.
Press the PLAY button
The VCR
VCR
22
on
playback picture
the VCR.
appears
on
the
screen.
Note : If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket of the set.
Connection of external
S-Video/Audio in sockets
When
connecting
picture quality will
1.
an
(S-Video) (option)
S-VIDEO VCR to the S-VIDEO
be further
equipment
socket, the
improved.
Connect the S-Video socket of the VCR to the S-VIDEO socket of the set.
2.
Connect the audio cable from the S-VIDEO VCR to the AUDIO
S-VIDEO VCR
sockets of the set.
3.
Select S-Video
4.
Press the PLAY button
The VCR
by pressing
on
playback picture
Headphone
the TV/AV/PC button
repeatedly.
the VCR.
appears
on
the
screen.
socket
Insert the
headphone plug to the headphone socket of the set. You
through the headphone and TV's speaker.
To adjust the headphone volume, press the Φ / Γ button. If you
press the MUTE button, the sound from the headphone and TV's
speaker are switched off.
can
listen to the sound
23
Connection of PC
PC in socket
1.
2.
3.
4.
PERSONAL COMPUTER
(D-Sub jack)
Connect the signal cable from the monitor output socket of the
PERSONAL COMPUTER to the PC input socket of the set.
Connect the audio cable from the PC to the PC SOUND sockets of the set.
Press the TV/AV/PC button to select PC.
Switch on the PC, and the PC screen appears on the set.
The set can be operated as the PC monitor.
Note
block
:
If you have
Apple macintosh, connect the VGA desktop
from the 3 row 15 pin to 2 row 15 pin with the
cable and connect the VGA desktop block to the Macintosh.
an
(not supplied)
signal
Displayable
MODE
Monitor
Specification
Resolution
Horizontal
Frequency(KHz)
VGA
SVGA
(MAC)
XGA
Vertical
Frequency(Hz)
640x350
31.4KHz
70Hz
640x350
37.8KHz
85Hz
640x400
31.4KHz
70Hz
640x400
37.8KHz
85Hz
640x480
31.5KHz
60Hz
640x480
35KHz
66Hz
640x480
37.9KHz
72Hz
640x480
37.5KHz
75Hz
640x480
43.3KHz
85Hz
800x600
35.2KHz
56Hz
800x600
37.9KHz
60Hz
800x600
48.1KHz
72Hz
800x600
46.9KHz
75Hz
800x600
53.7KHz
85Hz
832x624
49.7KHz
75Hz
1024x768
48.4KHz
60Hz
1024x768
56.5KHz
70Hz
1024x768
60.2KHz
75Hz
1024x768
68.7KHz
85Hz
(Synchronization input
form
:
separate)
Note :
a.
If the set is cold, there may be a small "flicker" when the set is
switched on. This is normal, there is nothing wrong with the set.
b. If possible, use the VESA 1,024x768@60Hz video mode to
obtain the best image quality for your LCD monitor. If used under
the other resolutions, some scaled or processed pictures may
appear on the screen. If used to PC vertical frequency 85Hz,
some noise can be seen when PIP is on. In this case, set the PC
vertical frequency to 60Hz. The set has been pre-adjusted to the
mode VESA 1,024x768@60Hz.
c.
Some dot defects may appear on the screen, like Red, Green or
Blue spots. However, this will have no impact or effect on the
monitor performance.
d.
Do not press the LCD screen with your finger for a long time as
this may produce some temporary distortion effects on the
screen.
e.
When the PC screen appears on the set, a message may appear
the screen, and the message will differ according to the
Window system version (Win98, 2000). If a message appears
click "Next" until the message finishes.
If the message "out of Range" appears on the screen, adjust
the PC as in the 'Displayable Monitor Specification' section.
on
f.
DPM (Display Power Management) mode
When the PC is in the power saving mode, automatically the
itor goes into DPM mode to save the energy.
24
mon-
Connection of PC
Menu selection
1.
2.
3.
Repeatedly
Press the
item.
Press the
Γ
press the MENU button to display each menu.
button and then Δ / Ε button to select a menu
button to
Γ
display
the sub
menu
or
the
pull-down
menu.
4.
Change
the
setting
of
an
item in the sub
or
pull-down
menu
with
Φ/ΓorΔ/Ε.
You can move to the higher level menu by pressing the OK or
Φ button and to move to the lower level menu
by pressing the
Γ button.
Note :
a.
See 'Picture adjustment' section to adjust the picture.
b. See 'Sound adjustment' section to adjust the sound.
c.
See 'TV, AV and PC modes' section to select TV, AV 1, AV 2, S-Video
or PC.
Picture
CH.
PSM
{
DRP
{
User
{
1
2
3
4
5
6
7
8
9
MENU/INDEX
0
PR
()O{OOKOMENU
Picture
VOL
menu
OK
VOL
PR
PCOSetup
Sound
CH.
SSM
{
O
Balance
{
O
AVL
{
+39
{
{
OClockkphase
{
OAuto_configure
{
OReset
{
M
menu
Special
CH.
{
()O}{OOKOMENU
()O{OOKOMENU
Sound
(H_Position)
(V_Position)
OClock
PIPOMENU
Input
Setup
{
PIP
{
OOff
{
Input
{
PIP
{
PR
{
Position
{
OPIP(S)
OPIP(M)
OPIP(L)
SoundOselect
{
}{OOKOMENU
()O{OOKOMENU
Special
menu
PC programme
25
Connection of PC
Special
Special
Menu
CH.
Input
Setup
{
PIP
{
{
()O{OOKOMENU
PC
Setup
You
can
1.
Repeatedly
2.
Press the
Press the
adjust horizontal/vertical position, clock,
configure and reset as you prefer.
3.
picture
clock
auto-
phase,
press the MENU button to select the Special menu.
button and then Δ / Ε button to select Setup.
Γ button and then Δ / Ε button to select the desired
item.
Γ
PCOSetup
O
O
1
2
3
(H_Position)
(V_Position)
{
+39
{
OClock
{
OClockkphase
{
OAuto_configure
{
OReset
{
()O}{OOKOMENU
4
5
6
7
8
9
4.
Press the
TV/AV/PC
MENU/INDEX
Φ
/
(H-Position)
0
button to make
Γ
/
This function is to
appropriate adjustments.
(V-Position)
adjust picture to left/right
and
up/down
as
you
prefer.
PR
VOL
OK
Clock
This function is to minimize any vertical bars or stripes visible on
screen background. And the horizontal screen size will also
VOL
the
change.
PR
Clock
phase
This function allows you to remove any horizontal noise and
clear or sharpen the image of characters.
Auto-configure
This function is for the automatic
adjustment
of the
posi-
screen
tion, clock and clock phase. The displayed image will disappear
M
for
a
few seconds while the
Auto-configuration
is in process.
Note : Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor's position, clock and clock phase manually.
Reset
This function allows you to return to the good picture reproduction programmed at the factory and cannot be changed.
5.
Press the OK button to store it for the PC monitor
6.
Repeatedly
viewing.
Note : If you turn on the
need to adjust PC Setup,
26
picture.
press the TV/AV/PC button to return to normal TV
PIP, you
please
can
not
get
in PC
turn off the PIP first.
Setup.
If you
PIP
PIP
operation
Special
operation
CH.
PIP
(Picture
in
Picture) displays
a
picture
within
a
picture
in the PC
Special
Input
Setup
{
PIP
{
Menu
{
mode.
1.
Repeatedly
2.
Press the
Γ
press the MENU button to select the Special menu.
button and then Δ / Ε button to select PIP.
()O{OOKOMENU
PIPOMENU
PIP
{
OOff
Input
{
PR
{
OPIP(S)
OPIP(M)
OPIP(L)
Position
{
SoundOselect
{
}{O OKOMENU
Press the
Press the
Γ
4.
Δ
button to display the PIP
/ Ε button to select PIP.
5.
Press the
Γ
button to select the desired sub
3.
You
can
(M),
or
also recall
PIP
(L))
6.
Press the OK
7.
Press the
desired sub
a
with PIP button
picture
on
size
picture
(Off,
PIP
Press the OK
Γ
3
4
5
6
(S),
PIP
7
8
9
TV/AV/PC
MENU/INDEX
0
9.
11. Press the
2
button.
or Φ
Δ / Ε button to select Input.
Press the Γ button and then Δ / Ε button to select
AV 2 or S-Video.
Δ
size.
the remote control.
8.
10. Press the
1
menu.
TV, AV 1,
VOL
button.
or Φ
PR-
/ Ε button to select PR.
button to select the programme number. Select the
PR+
PR
OK
VOL
PR
INPUT
desired programme number (0 to 99) with the Φ / Γ button or
NUMBER buttons on the PR pull-down menu. Any number under
10 is entered with a numeric '0' in front of it, i.e. '05' for 5.
12. Press the OK button.
13. Press the
Δ
14. Press the
Γ
/ Ε button to select Sound select.
button and then Δ / Ε button to select PC
POSITION
or
PIP
PIP
the Sound select pull-down menu.
or Φ button.
16. Press the Δ / Ε button to select Position.
17. Press the Γ button.
on
M
15. Press the OK
18. Press the
Δ
/ Ε
achieved. The sub
or
Φ
picture
/ Γ
button until desired
moves
19. Press the TV/AV/PC button to return to
Alternatively
you
can
select
PIP, POSITION, INPUT
or
or
position
left/right.
normal TV viewing.
up/down
is
or
operate the PIP function by using the
PR +/- buttons.
27
PIP
Special
On and off
Special
Menu
CH.
operation
Input
Setup
{
PIP
{
{
Select the PC mode.
Press the PIP button to switch
Press this button
()O{OOKOMENU
Input
again
on
the sub
mode selection for sub
Press the INPUT button to select the
picture
input
Each time this button is pressed, each
ture is displayed as shown below.
Programme
picture.
to switch it off.
number
mode for the sub
input
AV2
AV1
picture.
mode for the sub
pic-
S-Video
1
2
3
4
5
6
Programme
9
Press the PR +/- button. The selected programme number is displayed just below the programme number of main picture.
7
8
selection for sub
picture
0
Sub
PR-
PR+
PR
VOL
picture
size
Repeatedly press the PIP button to select the desired sub
size. The sub picture appears as below.
VOL
Off
PR
PIP
(S)
PIP
(M)
PIP
(L)
INPUT
Sub
picture position change
Press the POSITION button.
button until desired
POSITION
up/down
PIP
M
28
picture
or
position
press the Δ / Ε or Φ / Γ
is achieved. The sub picture moves
Repeatedly
left/right.
Note :
a.
If you turn on the TXT in PIP, some PIP keys, such as POSITION, INPUT or PR +/- etc. will work as TXT keys.
b. In PIP picture resolution will be decreased by the PIP size.
Troubleshooting
check list
Symptoms
No
picture,
no
Sound
sound
OK, poor picture
Picture
OK, poor sound
Picture blurred
Lines
or
streaks in
Poor
picture
reception
on some
channels
No colour
Poor colour
Remote control does not work
Incorrect
position
Vertical bars
or
stripes
on
background
Horizontal noise
Signal
Cable message appears
Check these items and try to
these
adjust
The mains plug-(plugged in and
switched on)
Is the TV switched
Try
on
another channel
(weak signal)
Check aerial
(plugged
into
Check aerial
(broken lead?)
TV?)
Check aerial
Check for local interference
Adjust
contrast
Adjust brightness
Adjust
colour
Adjust
volume
Check the batteries in remote control
Check Audio/Video sockets
Auto-configure
or
adjust
(VCR only)
the H/V
position
Auto-configure
or
adjust
Clock
Auto-configure
or
adjust
Clock Phase
Is the
Signal
Cable connected
or
loose
29
Note
Note
GUARANTEE
LG Electronics U.K. Ltd. will
provide
the
following
services in order to
expedite
this
Guarantee.
1.
All
faulty components which fail due to defective manufacture will be replaced
charge for a period of 12 months from the original date of purchase.
2.
The dealer
free of
(or his service agent) who sold the product will be reimbursed for any
provided in the repair of this LG equipment, for a period of 12 months from the
original date of purchase. These claims must be made in accordance with the published scale of service charges and relevant claims procedure.
labour
PLEASE NOTE:
A.
B.
The dealer may restrict the guarantee to the original purchaser.
The dealer is not obliged to carry out service under guarantee if unauthorized modifications
apparatus, or if non standard components are used or if the
apparatus is removed, defaced, misused, or altered.
C. Any claims made under guarantee must be directed to the dealer from whom the
are
made to the
serial number of the
D.
equipment was originally purchased. The dealer may, before carrying out service
under guarantee, require a receipted account as evidence of the date of purchase.
We respectfully point out that your dealer is not obligated to replace batteries if they
E.
Aerial
become exhausted
This
alignment
guarantee
or worn
and
in
use.
consumer
control
does not affect your
adjustments
are
not covered
this
by
guarantee.
statutory rights.
REQUIREMENTS TO MAINTAIN WARRANTY COVERAGE:
RETAIN YOUR RECEIPT TO PROVE DATE OF PURCHASE. A COPY OF YOUR RECEIPT
MUST BE SURRENDERED AT THE TIME GUARANTEE SERVICE IS PROVED.
Product
Registration
Card:
It is
helpful
to
complete
address, phone, model
at least your name,
& serial numbers
and return it. This will enable LG to assist
should you
your units be stolen,
modifications be necessary.
you
in the future
receipt,
To obtain information
or
assistance:
Call
0870
607
5544
lose your
should
or
Monday-Friday
9.00am-4.30pm.
Service website:
http://lgelectronics.co.uk
MODEL NO.*
*
Please
complete
for your
SERIAL NO.*
own
record
DATE OF PURCHASE
*
Download PDF