LG | RZ-23LZ50 | LG RZ-23LZ50 Owner’s Manual

LCD
Colour Television
OWNER'S MANUAL
Please read this manual
carefully
before
operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached
the back cover and quote this information to your dealer when you require service.
Model number
:
Serial number
:
P/NO
:
3828TUL295E
Printed in Korea
on
(0412-REV01)
Contents
Installation
3
Location and function of controls
4
Remote control handset
installation / Side
Battery
panel
Basic
9
operation
On and off / Programme selection
Volume adjustment / Quick view
Mute function
On
On
language
screen
selection
(option)
10
screen menus
Menu selection
up TV stations
Auto programme tuning
Manual programme tuning
Programme edit
Favourite programme
Calling the programme table
Setting
11
Picture
16
Sound
18
Time Menu
20
adjustment
PSM (Picture Status Memory)
Picture adjustment
Picture format (option)
adjustment
SSM (Sound Status Memory)
Sound adjustment / Stereo/Dual reception
NICAM reception (option) / Sound output selection
Clock / On/Off time
Auto off /
Sleep
timer
Other functions
22
TV, AV and PC modes
Auto AV
switching
/ Child lock
Teletext
24
Switch on/off
SIMPLE text / TOP text
FASTEXT /
Special
(option)
teletext functions
Connection of external
27
equipment
Aerial socket
Euro scart socket / Audio/Video in sockets
S-Video/Audio in sockets
DVD
input sockets
Headphone socket
(S-Video) (option)
(option)
(option)
Connection of PC
PC
PC
(option)
in socket (option)
Setup (only DVI-Analogue mode) (option)
External Control Device
Troubleshooting
2
Setup
check list
; RS-232C
(option)
29
31
35
Installation
Power
-
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set.
In the event of thunderstorms
or
powercuts, please pull
out the
aer-
Here shown may be somewhat
different from your set.
a
ial and mains plugs.
a. Open the back panel cover.
b. After connecting the power cord to the set, connect the power
cord to an AC mains.
c.
Fix cables with the supplyed cable tie after arranging connected
cables.
d. Pull the cables through the hole on the set.
e. Close the back panel cover.
e
Warning
To
prevent fire
or
shock
moisture. Do not rub
hard
as
this may
or
hazard, do
not expose the set to rain
strike the Active Matrix LCD with
scratch,
mar,
or
damage
or
anything
the Active Matrix LCD
permanently.
Service
Never
the back cover of the set as this can expose you to
and other hazards. If the set does not operate proper-
remove
high voltage
ly, unplug it and
b
call your dealer.
Aerial
Connect the aerial cable to the socket marked +75 Ω
For the best
reception
an
on
the back.
outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto
the screen. Care should be taken not to expose the set to any
d
unnecessary vibration, moisture, dust or heat. Also ensure that the
set is placed in a position to allow a free flow of air. Do not cover
the ventilation openings on the back cover.
This standing angle can be adjusted as shown in pictures.
If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of the TV.
When you install the set to use the wall mounting bracket (optional
parts), fix it carefully so as not to drop.
Cleaning
Unplug
the set before
cleaning
the face of the LCD Screen. Dust
the set
by wiping the screen and the cabinet with a soft, clean
If the screen requires additional cleaning, use a clean, damp
Do not use liquid cleaners or aerosol cleaners.
On
cloth.
cloth.
Disposal
The fluorescent
lamp
used in this
product
contains
a
small amount
of mercury.
Do not dispose of this
product with general household waste.
Disposal of this product mute be carried out in accordance to
regulations of your local authority.
the
3
ENGLISH
Location and function of controls
All the functions
can
be controlled with the remote control handset.
Some functions
panel of the set.
also be adjusted with the buttons on the side
Only the remote control handset supplied will opercan
ate this set.
Remote control handset
10
MUTE
POWER
1
11
TV/AV MULTIMEDIA
I/II
Before you use the remote control
teries. See the next page.
1.
12
2
LIST
MUTE
switches the sound
13
2.
clears the
VOL
or
AV monitor mode.
menu
switches the set
OK
3.
VOL
4.
5.
78
SLEEP
ARC
PSM
14
SIZE
MIX
HOLD
REVEAL
adjusts
menu
settings.
7.
SSM
8.
ARC
from
on
the current mode.
displays
standby
and selects
(Sound Status Memory)
recalls your preferred sound setting.
MODE
M
(option)
select your desired
9.
picture
sleep
10. MULTIMEDIA
timer.
(option)
selects COMPONENT
(With ARC/MULTIMEDIA)
format.
SLEEP
sets the
4
or
NUMBER BUTTONS
switches the set
?
i
a
TIME
6.
INDEX
selects
accepts your selection
15
UPDATE
(Programme Up/Down)
OK
TEXT
9
D / E
a
viewed programme.
favourite programme.
previously
programme or a menu item.
switches the set on from standby.
F / G (Volume Down/Up)
adjusts the volume.
789
0
standby.
Q.VIEW
selects
456
from
on
screen.
the programme table.
returns to the
123
from the
LIST
displays
PR
SSM
off.
TV/AV
selects TV
PR
6
on or
Q.VIEW MENU
34
5
handset, please install the bat-
or
PC monitor mode.
a
programme.
Location and function of controls
ENGLISH
11. POWER
switches the set
on
from
standby
or
off to
standby.
12. I/II
selects the
selects the
language during dual language
sound output (option).
broadcast.
13. MENU
selects
a menu.
MUTE
11
1
14. PSM
(Picture Status Memory)
recalls your preferred picture setting.
TV/AV
For further
*
:
are
details,
12
LIST
used for teletext.
see
34
the 'Teletext' section.
PR
COLOURED BUTTONS
models)
Q.VIEW MENU
13
No function
TELETEXT
I/II
2
15. TELETEXT BUTTONS
These buttons
POWER
or
:
These buttons
are
used for teletext
(only
OK
5
VOL
programme edit.
VOL
PR
Battery
installation
123
The remote control handset is powered by two AAA/Alkaline type batteries. To load the
the
remote
control
batteries,
turn
handset
over
and open the battery compartment.
Install two batteries as indicated by
the polarity symbols ( + and
)
6
456
789
7
SSM
0
PSM
14
-
marked inside the
SLEEP
compartment.
TEXT
15
9
Note : To avoid damage from possible battery leakage, remove the
batteries if you do not plan to use the remote control handset for an
extended period of time.
UPDATE
TIME
SIZE
MIX
HOLD
REVEAL
?
INDEX
i
MODE
M
(Without ARC/MULTIMEDIA)
5
Location and function of controls
*
:
The mark consists of blank
or
alphabet.
Side
RZ-23/26/27/30/32LZ50***
PR
7
VOL
6
OK
MENU
TV
AV/PC
9
8
panel
5
4
2
1
10
RZ-26LZ30
***
PR
VOL
OK
MENU
7
6
5
4
TV
AV/PC
/I
ONO
2
1
8
9
10
RZ-17LZ50
***
PR
7
VOL
6
OK
5
MENU
4
TV
AV/PC
/I
2
1
ONO
89
10
RZ-15LA70
***
PR
7
VOL
6
OK
5
MENU
9
R
8
4
TV/A PC
2
1
/ION/F
10
RZ-15LA66
***
PR
VOL
5
MENU
4
TV
9
/I
ON/OFF
8
10
6
6
OK
AV/PC
R
7
2
1
Location and function of controls
Side
RZ-20LA70
panel
***
PR
7
VOL
6
OK
9
R
5
MENU
TV/AV
4
31
/ION/F
10
RZ-20LA66
ENGLISH
8
***
7
PR
6
VOL
5
OK
4
MENU
TV
AV
9
31
/I
ON/OFF
8
10
RZ-23LZ41
***
7
PR
6
VOL
5
OK
4
2
MENU
9
R
TV
AV/PC
1
/I
ON/OFF
8
10
RZ-20LZ50
***
PR
VOL
OK
MENU
7
6
5
4
TV
AV
/I
ONO
3
1
89
10
RZ-20LA90
***
PR
7
VOL
6
OK
MENU
TV/AV
R
9
ON/OF
/I
54
31
8
10
7
Location and function of controls
RZ-17LZ40
Top panel
***
ON/OFF
TV/AV/PC
MENU
OK
VOL
1
2
4
5
6
PR
7
9
R
8
10
1.
ON/OFF(
/I)
switches the set
on
from
standby
or
(Volume Down/Up)
adjusts the volume.
adjusts menu settings.
7.
D / E
off to
standby.
2.
TV/AV/PC
selects
TV, AV
clears the
or
menu
switches the set
3.
clears the
or
from
standby.
8.
REMOTE CONTROL SENSOR
9.
POWER/STANDBY INDICATOR
menu
from the
on
from
illuminates red in
screen.
standby.
on.
10. Stand
a menu.
OK
accepts your selection
mode.
or
displays
standby
( )
mode.
illuminates green when the set is switched
MENU
selects
8
screen.
AV mode.
switches the set
5.
programme or a menu item.
switches the set on from standby.
a
TV/AV
selects TV
4.
on
(Programme Up/Down)
selects
PC monitor mode.
from the
F / G
6.
the current
(option)
Basic
operation
ENGLISH
On and off
1.
Press the POWER, D / E, TV/AV, MULTIMEDIA
NUMBER buttons to switch it on fully.
2.
Press the POWER button. The set reverts to
3.
Pull out mains
Note
MUTE
POWER
If, while the
:
is
replaced
standby
or
mode.
to switch the set off.
set is switched on, the mains
nected the set will switch to
plug
TV/AV MULTIMEDIA
plugs
(option)
standby
or
power
in the mains power socket.
on
plug
is discon-
when the mains
I/II
Programme
selection
You
a
Q.VIEW MENU
can
select
programme number with the D / E
or
NUMBER
buttons.
PR
Volume
OK
adjustment
VOL
VOL
Press the F / G button to
PR
adjust
the volume.
Quick view
123
Press the Q.VIEW button to view the last programme you
456
789
SSM
were
watching.
Note : This function works only when Favourite programme is set
to Off. Otherwise each press of this button will select a stored
favorite programme.
0
Mute function
Press the MUTE button. The sound is switched off and the
display
appears.
You can cancel it
button.
On
The
screen
menu
by pressing
language
can
be
guage. First select
1.
3.
MUTE,
selection
displayed on the
your language.
F /
G, I/II,orSSM
(option)
screen
Press the MENU button and then D / E
Setup
2.
the
in your desired lan-
button to select the
menu.
Press the G button and then D / E button to select Language.
Press the G button and then D / E button to select your desired
language.
All the
on screen
displays
will appear in the selected
4.
Press the OK button.
5.
Press the TV/AV button to return to normal TV
language.
viewing.
9
On
screen menus
Menu selection
2.
Press the MENU button and then D / E button to display each menu.
Press the G button and then D / E button to select a menu item.
3.
Change
1.
the
setting
of
an
item in the sub
or
pull-down
menu
with
F / G button.
You
can move
ton and to
to the
move
higher
level
by pressing the OK butmenu by pressing the MENU
menu
to the lower level
button.
Note :
In the TV/AV, COMPONENT (option) mode, the PC
a.
(option) is not displayed.
b. In the teletext mode, menus are not displayed.
c.
On some models, the Language will not be displayed.
MENU
Picture
Channel
Auto programme
PSM
Manual programme
Contrast
Programme edit
Brightness
Favourite programme
Colour
PR
OK
VOL
Sharpness
DEFG
OK
DEFG
MENU
Channel
OK
MENU
Picture
menu
Setup
menu
SSM
Language
AVL
Input
Balance
Child lock
DEFG
OK
MENU
Setup
DEFG
OK
MENU
Sound
menu
Time
Time
Off time
On time
Auto off
DEFG
OK
MENU
Time
menu
VOL
PR
Sound
10
menu
menu
Setting
Channel
TV
stations
up
programme numbers (0 to 99).
Once you have preset the stations, you will be able to use the D / E
or NUMBER buttons to scan the stations you have programmed.
Stations can be tuned using automatic or manual modes.
Up
Auto programme
Manual programme
Programme edit
Favourite programme
to 100 TV stations
can
Auto programme
DEFG
OK
be stored
by
tuning
All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set.
MENU
1.
2.
Press the MENU button and then D / E button to select the
Channel menu.
Press the G button and then D / E button to select Auto programme.
Auto programme
TV/AV
System
BG
Storage from
I
Search
DK
L
M
MENU
DEFG
Press the G button. Select a TV system with the G button and
then D / E button on the System menu;
BG : PAL B/G, SECAM B/G (Europe/East Europe)
I
: PAL I/II (U.K./Ireland)
DK : PAL D/K, SECAM D/K (East Europe)
L
: SECAM L/L' (France)
M
: (USA/Korea/Philippines)
4.
Press the OK button.
5.
Press the D / E button to select Storage from.
Select the beginning programme number with the F / G button
or NUMBER buttons on the Storage from pull-down menu. Any
number under 10 is entered with a numeric '0' in front of it, i.e.
'05' for 5.
Press the D / E button to select Search.
Press the G button to begin auto programming.
OK
VOL
PR
123
6.
456
789
MENU
3.
PR
VOL
OK
7.
8.
0
Auto programme
System
Storage from
Search
C21
2
BG
5
%
MENU
All receivable stations are stored. The station name is stored for
stations which broadcast VPS (Video Programme Service),
PDC (Programme Delivery Control) or TELETEXT data. If no
station name can be assigned to a station, the channel number
is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47),
followed by a number.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit
menu appears on the screen. See the 'Programme edit' section
to edit the stored programme.
9.
Press the TV/AV button to return to normal TV
viewing.
11
ENGLISH
TV
stations
up
Setting
Manual programme
tuning
Channel
Auto programme
Manual programme
Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station
name
1.
2.
3.
Programme edit
Favourite programme
with five characters to each programme number.
Press the MENU button and then D / E button to select the
Channel menu.
DEFG
OK
MENU
Press the G button and then D / E button to select Manual programme.
Press the G button and then D / E button to select Storage.
Manual programme
29
Storage
System
Channel
TV/AV
Search
Name
MENU
DEFG
4.
5.
6.
OK
MENU
Select the desired programme number (0 to 99) with the F / G
button or NUMBER buttons on the Storage menu. Any number
under 10 is entered with a numeric '0' in front of it, i.e. '05' for 5.
Press the D / E button to select System.
Select a TV system with the G button and then F / G button
the
System
PAL
I
:
DK
:
PAL I/II (U.K./Ireland)
PAL D/K, SECAM D/K
M
:
(East Europe)
(France)
(USA/Korea/Philippines)
456
Press the OK button.
8.
Press the D / E button to select Channel.
Press the G button and then D / E button to select VHF/UHF
Cable on the Channel menu.
If
possible, select the channel number directly
buttons. Any number under 10 is entered with
or
with the number
a
numeric '0'
in
it, i.e. '05' for 5.
10. Press the OK button.
11. Press the D / E button to select Search.
12. Press the G button and thenF / G button to
ing
on
the Search
search will
pull-down
menu.
If
a
commence
stop.
Storage
System
Channel
Search
GGG
Name
DEFG
OK
MENU
13. Press the OK button to store it.
14. To store another
station, repeat steps 3
search-
station is found the
Manual programme
to 13.
15. Press the TV/AV button to return to normal TV
12
VOL
123
SECAM L/L'
front of
VOL
B/G, SECAM B/G (Europe/East Europe)
7.
9.
on
PR
:
:
OK
menu;
BG
L
PR
viewing.
789
0
Setting
Assigning a station name
1.
Repeat the 'Manual programme tuning' steps
Channel
Auto programme
Manual programme
Programme
TV
stations
up
edit
Favourite programme
1 to 2.
2.
Press the G button and then D / E button to select Name.
3.
Press the G button and then
4.
-,thenumber0to9andthealphabetAtoZ.
With the F button you can select in the opposite direction.
Select the position by pressing the F / G button and then
5.
your choice of the second character, and
Press the OK button to store it.
6.
Press the TV/AV button to return to normal TV
use
ENGLISH
the D / E. You
can use a
blank,
+,
DEFG
OK
MENU
make
so on.
viewing.
TV/AV
MENU
PR
OK
VOL
VOL
PR
13
Setting
Programme
TV
stations
up
Channel
edit
Auto programme
Manual programme
This function enables you to delete or skip the stored programmes.
Also you can move some stations to other programme numbers or
insert a blank station data into the selected programme number.
1.
Press the MENU button and then D / E button to select the
Channel menu.
2.
Press the G button and then D / E button to select
edit.
Programme
3.
Press the G button to
menu.
display
the
0C0 35S
Deleting
1.
2.
Programme edit
6S17
2C1 2
7-----
3S6 6
8-----
4S6 7
9-----
Copy
Move
Skip
Favourite programme
DEFG
OK
MENU
69
1BLN03
Delete
Programme edit
TV/AV
MENU
a
programme
Select a programme to be deleted with the D / E or F / G button.
Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one position.
PR
OK
VOL
0C035S
69
1BLN03
6S17
2C1 2
7-----
3S66
8-----
4S67
9-----
VOL
PR
123
Delete
456
Copying
1.
2.
programme
Select a programme to be copied with the D / E
Press the GREEN button.
All the following programmes are shifted down
Moving
1.
2.
3.
a
or
F / G button.
one
position.
a
programme
Select a programme to be moved with the D / E or F / G button.
Press the YELLOW button.
Move the programme to the desired programme number with
theD/EorF/Gbutton.
4.
Press the YELLOW button
Skipping
a
Select
a
1.
again
programme number
programme number to be
to release this function.
skipped
with the D / E
or
F / G
button.
2.
3.
Press the BLUE button. The
programme turns to blue.
Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be
unable to select it using the D / E button during normal TV
viewing. If you want to select the skipped programme, directly
enter the programme number with the NUMBER buttons or
select it in the programme edit or table menu.
skipped
Press the TV/AV button to return to normal TV
14
viewing.
789
0
TV
stations
up
Setting
ENGLISH
Favourite programme
Channel
Auto programme
This function lets you select your favourite programmes
Manual programme
Programme edit
Favourite programme
directly.
1.
Press the MENU button and then D / E button to select the
Channel menu.
2.
Press the G button and then D / E to select Favourite programme.
DEFG
OK
MENU
Favourite programme
On
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
--
-----
DEFG
3.
TV/AV
4.
5.
LIST
Q.VIEW MENU
6.
7.
or
Off.
--
the Q.VIEW button to select stored favourite pro-
grammes.
OK
VOL
MENU
Press the G button and then F / G button to select On
Press the D / E button to select
-----.
Select a desired programme with the F / G button.
To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
Press the TV/AV button to return to normal TV viewing.
Repeatedly press
PR
OK
VOL
PR
Calling
You
the programme table
check the programmes stored in the memory
the programme table.
123
456
can
Displaying programme
table
Press the LIST button to
display
the
by displaying
Programme table
menu.
The programme table appears on the screen. One programme
table contains ten programmes as below.
789
0C0 35S
0
69
1BLN03
6S17
2C12
7S22
3S66
8C09
4S67
9C11
Note :
a.
You may find some blue programmes. They have been set up to
be skipped by auto programming or in the programme edit mode.
b.
Some programmes with the channel number shown in the programme table indicate there is no station name assigned.
programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
Selecting
a
The set switches to the chosen programme number.
programme table
10 programme table pages in which contain 100 pro-
Paging through
There
are
a
grammes.
Pressing the D / E
or
F / G button
repeatedly
Press the TV/AV button to return to normal TV
turns the pages.
viewing.
15
Picture
PSM
1.
2.
3.
Memory)
Picture
Press the MENU button and then D / E
Picture menu.
PSM
button to select the
Contrast
Brightness
Colour
Press the G button and then D / E button to select PSM.
Press the G button and then D / E button to select a picture set-
ting
4.
Status
(Picture
adjustment
on
the PSM
Sharpness
menu.
Press the OK button.
DEFG
OK
MENU
Picture
PSM
Dynamic
Contrast
Standard
Brightness
Mild
Colour
Game
Sharpness
User
DEFG
5.
OK
MENU
TV/AV
Press the TV/AV button to return to normal TV
viewing.
MENU
picture (Dynamic, Standard, Mild,
Game or User) with PSM button on the remote control. The picture
Dynamic, Standard, Mild and Game are programmed for optimum
picture reproduction at the factory and cannot be changed.
You
can
also recall
a
desired
PR
Picture
You
can
ness
1.
to
adjustment
OK
adjust picture contrast, brightness,
the levels you prefer.
colour
Press the MENU button and then D / E
Picture menu.
intensity, sharp-
VOL
VOL
PR
button to select the
Picture
PSM
Contrast
47
Contrast
Brightness
Colour
Sharpness
DEFG
OK
PSM
MENU
3.
Press the D / E button to select the desired
Press the F / G button to make appropriate
4.
Press the TV/AV button to return to normal
2.
Note
16
:
Only
Contrast and
Brightness
are
picture
item.
adjustments.
TV viewing.
displayed
in PC mode.
Picture
adjustment
Picture format
You
ENGLISH
(option)
watch TV in various
Spectacle, Original, 4:3.
can
picture formats; 16:9, 14:9, Zoom,
press the ARC button to select your desired
Repeatedly
picture
for-
mat.
16:9
You
enjoy the cinema (the picture format of 16:9) or general TV
programme through the 16:9 mode.
The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and right so that the screen 16:9 is full.
can
14:9
You
TV/AV
the picture format of 14:9
the 14:9 mode.
can
through
The
MENU
enjoy
screen
14:9 is viewed
to the upper / lower and
just like
left / right.
or
that the
TV programme
general
screen
4:3 is
magnified
Zoom
You
The
PR
so
OK
VOL
VOL
PR
the cinema in a vast screen through the Zoom mode.
screen 4:3 is magnified to the upper / lower and left / right sides
that the screen 16:9 is full. The bottom and top of the picture
can
enjoy
may be lost.
Spectacle
When your TV receives the wide
adjust the picture horizontally, in
entire
signal, it will lead
nonlinear proportion, to
screen
a
you to
fill the
screen.
Original
When your TV receives the wide screen signal, it will be automatically changed to the picture format to be sent.
4:3
This
ARC
picture
Note
:
format is 4 to 3 of
In PC mode
only
general
16:9 and 4:3
TV.
aspect ratios
are
available.
17
Sound
SSM
You
Sound
(Sound Status Memory)
SSM
select your preferred sound setting; Flat, Music, Movie or
and you can also adjust the sound frequency of the equalizer.
can
Speech
1.
adjustment
AVL
Balance
Press the MENU button and then D / E button to select the
Sound menu.
Sound
SSM
Flat
AVL
Music
Balance
Movie
DEFG
OK
MENU
Speech
G
User
DEFG
2.
3.
OK
MENU
Press the G button and then D / E button to select SSM.
Press the G button and then D / E button to select a sound setting on the SSM menu.
Sound Frequency Adjustment
a. Press the OK button in User.
b. Select a sound band by pressing the F / G button.
c. Make appropriate sound level with the D / E button.
d. Press the OK button to store it for the sound User.
TV/AV
MENU
PR
OK
VOL
VOL
PR
0.1
0.5
1.5
5
10Khz
Press the TV/AV button to return to normal TV
You
viewing.
also recall a desired sound setting (Flat, Music, Movie, Speech
or User) with SSM button on the remote control. The sound settings
Flat, Music, Movie and Speech are programmed for optimum sound
reproduction at the factory and cannot be changed.
can
If you press the SSM button after making appropriate adjustment on the User sub menu, the display User automatically
appears even though you have already set a factory preset setting;
Flat, Music, Movie or Speech.
Note
:
Sound
SSM
DEFG
Sound
You
AVL
On
Balance
Off
OK
MENU
adjustment
adjust balance, AVL (Auto
ically keeps on an equal volume
can
Volume Leveler). AVL automatlevel even if you change pro-
grammes.
1.
2.
3.
Press the MENU button and then D / E button to select the
Sound menu.
Press the G button and then D / E button to select the desired
sound item; AVL or Balance.
Make desired adjustment with the F / G, D / E and then press
the OK button.
4.
18
Press the TV/AV button to return to normal TV
viewing.
SSM
Sound
adjustment
Stereo/Dual
When
reception
programme is selected, the sound information for the station appears after the programme number and station name disappear.
I/II
a
Broadcast
On Screen
Mono
MONO
Stereo
STEREO
Dual
DUAL I
Display
Mono sound selection
In stereo
reception if the stereo signal is weak, you can switch to
mono by pressing the I/II button twice. In mono reception the depth
of sound is improved. To switch back to stereo, press the I/II button twice again.
Language
If
OK
selection for dual
programme is received in
switch to DUAL I, DUAL II
a
can
ton
language broadcast
two languages (dual language),
or DUAL I+II by pressing the I/II
you
but-
repeatedly.
DUAL I sends the
DUAL II sends
primary broadcast language to the loudspeakers.
the secondary broadcast language to the loud-
speakers.
DUAL I+II sends
NICAM
a
separate language
to each
loudspeaker.
reception (option)
If your set is
equipped
with the receiver for NICAM
reception, the
Companding Audio
high quality NICAM (Near Instantaneous
Multiplex) digital sound can be received.
Sound output can be selected according to the type of received
broadcast as follows by pressing the I/II button repeatedly.
1.
When NICAM
or
2.
mono
is
received, you
can
FM MONO.
When
NICAM
stereo
is
received, you
STEREO or FM MONO. If the stereo
FM mono.
3.
select NICAM MONO
When NICAM dual is
NICAM DUAL II
mono
or
is selected the
can
signal
is
select
NICAM
weak, switch
to
select NICAM DUAL I,
NICAM DUAL I+II or MONO. When FM
received, you
display
can
MONO appears
on
the
screen.
Sound output selection
In AV
mode, you
can
select
output sound for the left and right loud-
speakers.
press the I/II button to select the sound output.
Audio signal from audio L input is sent to left loud-speaker
and audio signal from audio R input is sent to right loud-
Repeatedly
L+R
L+L
R+R
:
:
:
speaker.
Audio signal
speakers.
Audio signal
speakers.
from audio L
input
is sent to left and
right
loud-
from audio R
input
is sent to left and
right
loud-
19
ENGLISH
TIME Menu
Clock
Time
Time
You must set the time
1.
using
Off time
on/off time function.
Press the MENU button and then D / E
TIME
2.
correctly
before
On time
button to select the
Auto off
menu.
Press the G
button and then D / E button to select TIME.
Time
DEFG
Time
OK
MENU
-i-i:i-i-
Off time
On time
Auto off
DEFG
OK
MENU
3.
Press the G
4.
Press the G button and then D / E button to
5.
Press the MENU button to
button and then D / E button to
adjust the hour.
adjust the minute.
save.
MENU
On/Off time
The off timer
automatically
switches the set to
at the pre-
standby
set time.
PR
1.
Press the MENU button and then D / E
TIME
2.
button to select the
menu.
VOL
Press the G button and then D / E button to select Off time
or
On time.
3.
button and then D / E button to select On.
To cancel On/Off time function, press the D / E button to
Press the G
select Off.
Time
Time
Off time
On time
-i-i:i-i-
Auto off
Pr.
0
Vol.
30
On
DEFG
OK
MENU
Press the G
5.
button and then D / E button to adjust the hour.
Press the G button and then D / E button to adjust the minute.
6.
Only
4.
On time
button to
7.
function; Press the
:
In the event of power interruption
ure), the clock must be reset.
b.
Two hours after the set is switched
will
automatically switch back
has been pressed.
d.
20
to
(disconnection
or
power fail-
by the on time function it
standby mode unless a button
on
Once the on or off time is set, these functions operate daily at
the preset time.
Off Timer function overrides On Timer function if they are set to
the
e.
button and then D / E
adjust
a.
c.
G
volume level and programe number.
Press the MENU button to save.
Note
same
OK
time.
The set must be in
standby mode for the On Timer
to work.
VOL
PR
TIME Menu
Time
ENGLISH
Auto off
Time
Off time
If you select On on the Auto off menu, the set will automatically
switch itself to standby mode approximately ten minutes after a TV
On time
Auto off
station
DEFG
OK
MENU
stops broadcasting.
1.
Press the MENU button and then D
TIME menu.
2.
Press the G button and then D
Press the G button and then D
3.
/ E
button to select the
button to select Auto off.
E button to select On or Off.
/ E
/
Time
Time
Off time
On time
On
Auto off
Off
MENU
DEFG
4.
OK
VOL
VOL
PR
MENU
Press the MENU button to
Sleep
PR
OK
save.
timer
You don't have to remember to switch the set off before you go to
sleep. The sleep timer automatically switches the set to standby
after the
preset time has elapsed.
Press the SLEEP button to select the number of minutes. The disoff' will appear on the screen, followed by 10, 20, 30, 60,
play
90, 120, 180 and 240. The timer begins to count down from the
'
number of minutes selected.
Note :
a.
To view the
remaining sleep time,
press the SLEEP button
once.
b.
To cancel the sleep time, repeatedly press the SLEEP button
off' appears.
until the display
When you switch the set off, the set releases the preset sleep
time.
'
SLEEP
c.
21
Other functions
TV, AV and PC modes
Inputs
can
be set for
AV
TV,
video cassette recorder
Setup
Language
or
(VCR),
PC mode. AV mode is used when
or
other
Input
a
Child lock
is connected to
equipment
the set.
Note : When a VCR is connected via the aerial socket the set is
used in TV mode. See the 'Connection of external equipment' section.
1.
3.
OK
MENU
Press the MENU button and then D / E button to select the
Setup
2.
DEFG
menu.
Press the G button and then D / E button to select Input.
Press the G button and then D / E button to select TV, AV1,
AV2, AV3 (option), S-Video, Component (option) or PC (option).
The AV and PC modes
are :
TV/AV
Setup
Language
Input
TV
Child lock
AV1
MENU
AV2
AV3
S-video
Component
PR
PC
DEFG
OK
MENU
AV 1
:
VCR connected to the Euro scart socket of the set.
AV 2
:
VCR connected to the AV2 of the set.
AV 3
:
VCR connected to the AV3 of the set.
S-Video
:
:
(option)
on
the back
123
(option)
PERSONAL COMPUTER connected to the PC socket of
the set.
4.
VOL
PR
DVD connected to the DVD IN sockets
of set.
:
VOL
VCR connected to the S-Video of the set.
Component
PC
OK
456
(option)
Press the TV/AV button to return to normal TV
Alternatively
you
TV/AV button.
can
select the TV
or
AV mode
viewing.
by pressing
the
789
0
In AV
mode,
to return to TV
mode, press the
D / E
or
NUMBER but-
tons.
Auto AV
switching
If your VCR outputs an AV switching voltage when connected to the
Euro scart socket, the set will switch to AV1 mode automatically. But
if you want to
BER buttons.
keep
on
watching
TV
mode, press the
Press the TV/AV button to return to AV modes.
22
D / E
or
NUM-
Other functions
ENGLISH
Child lock
Setup
Language
Input
The TV
Child lock
can
be set
so
that the remote control handset is needed to
control it. This feature
can
be used to
prevent unauthorized view-
ing.
DEFG
OK
1.
MENU
Press the MENU button and then D / E button to select the
Setup
2.
3.
menu.
Press the G button and then D / E button to select Child lock.
Press the G button and then D / E button to select On or Off
on the Child lock menu.
Setup
Language
Input
Child lock
On
Off
TV/AV
MENU
DEFG
4.
OK
VOL
PR
MENU
Press the TV/AV button to return to normal TV
viewing.
With the lock on, the display Child lock appears on the screen if
any button on the side panel is pressed while viewing the TV.
PR
VOL
OK
Note : The display Child lock will not appear on the screen if any
button on the panel is pressed while displaying the menus.
23
Teletext
Teletext
(or
TOP
with the teletext
Teletext is
a
text)
is
system
an
can
therefore
optional function,
only
a
set
receive the teletext broadcast.
free service broadcast
by
most TV stations which
information on news, weather,
grammes, share prices and many other topics.
gives
television
up-to-the-minute
pro-
The teletext decoder of this TV can support the SIMPLE, TOP and
FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern
methods
allowing quick
and easy selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext. The initial page
page appears on the screen.
or
last
Two page numbers, TV station name, date and time are displayed
on the screen headline. The first page number indicates your selection, while the second shows the current page displayed.
Press the TEXT button to switch off teletext. The
PR
SIMPLE text
1.
2.
OK
mode
previous
reappears.
Page
PR
123
selection
Enter the desired page number as a three digit number with the
NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number.
The D / E button can be used to select the
lowing
preceding
or
456
789
fol0
page.
TEXT
Programming
a
colour button in LIST mode
If the TV is in SIMPLE text, TOP text
M button to switch to LIST mode.
or
FASTEXT
mode, press the
Four teletext page numbers of your choice can be colour coded and
easily selected by pressing the corresponding coloured button on
the remote control handset.
1.
Press
a
2.
Using
the NUMBER
3.
4.
24
coloured button.
buttons, select the page you wish
MODE
to pro-
gramme.
Press the OK button. Then the selected page is stored as the
selected page number by blinking once. From now on, you can
select this page with the same coloured button.
The three other coloured buttons are programmed in this way.
M
Teletext
TOP text
The
user
ENGLISH
(option)
guide displays
the bottom of the
four
fields-red, green, yellow and blue
field denotes the next group
and the blue field indicates the next block.
screen.
The
at
yellow
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next block.
3.
With the green button you can proceed to the next
page with automatic overflow to the next group.
the D button can be used.
button permits to return to
existing
Alternatively
4.
The
red
the E button
Alternatively
can
previous
selection.
be used.
Direct page selection
Corresponding to the SIMPLE teletext mode, you can select a page
by entering it as a three digit number using the NUMBER buttons in
PR
TOP mode.
OK
FASTEXT
PR
The teletext pages are colour coded along the bottom of the screen
and are selected by pressing the corresponding coloured button.
123
Page
456
selection
i button to select the index page.
1.
Press the
2.
You
3.
Corresponding to the SIMPLE
page by entering its three digit
789
0
select the pages which are colour coded
tom line with the same coloured buttons.
can
teletext
along
mode, you
can
the botselect
a
page number with the NUMBER
buttons in FASTEXT mode.
4.
The D / E button
lowing
can
be used to select the
preceding
or
fol-
page.
INDEX
i
M
25
Teletext
Special
?
teletext functions
REVEAL
Press this button to
display concealed information, such as
solutions of riddles or puzzles.
Press this button again to remove the information from the
display.
SIZE
Selects double
Press
Press
height text.
this button to enlarge the top
this button again to enlarge
page.
Press this button
again
half of the page.
the bottom half of the
to return to the normal
display.
PR
UPDATE
Displays
the TV
picture on
The display
the
screen
while
waiting
for the
new
teletext page.
will appear at the top left hand
corner of the screen. When the updated page is available then
will change to the page number.
display
Press this button to view the updated teletext page.
PR
123
HOLD
the automatic page
text page consists of 2 or
tele-
456
sub pages. The number of
sub pages and the sub page displayed is, usually, shown on
the screen below the time. When this button is pressed the
789
Stops
stop symbol is displayed
change
which will
occur
if
a
more
at the
top left-hand
corner
of the
0
and the automatic page change is inhibited.
To continue press this button again.
screen
MIX
the teletext pages superimposed on the TV
To switch the TV picture off press this button again.
Displays
picture.
TIME
TV programme, press this button to display
the time at the top right hand corner of the screen. Press this
viewing
button
again
a
to
remove
the
display.
In the teletext
mode,
press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or
the sub page, press the
NUMBER buttons.
change
26
TIME
SIZE
MIX
HOLD
REVEAL
?
When
Press
UPDATE
again
to exit this function.
RED/GREEN,
D
/ E
or
Connection of external
You
equipment
connect additional equipment, such
etc. to your set. Examples are shown below.
can
as
VCRs, camcorders
Aerial socket
1.
2.
3.
VCR
4.
5.
Connect the RF out socket of the VCR to the aerial socket of
the set.
Connect the aerial cable to the RF aerial in socket of the VCR.
Store the VCR channel on a desired programme number using
the 'Manual programme tuning' section.
Select the programme number where the VCR channel is
stored.
Press the PLAY button on the VCR.
Euro scart socket
1.
VCR
2.
3
Connect the Euro scart socket of the VCR to the Euro scart
socket of the set.
Press the PLAY button on the VCR.
If your VCR outputs an AV switching signal via the Scart lead the
set will auto switch to AV 1, AV 2 mode on start of playback, but
if you want to keep on watching in TV mode, press the D / E or
NUMBER buttons.
Otherwise press the TV/AV button on the remote control handset to select AV1. The VCR play back picture appears on the
screen.
You
can
also record programmes received
by
the TV
on
video
tape.
VCR
Note
a.
b.
c.
VCR
d.
:
i.e. the signals red, green and blue can only
be selected for the Euro scart 1 and the AV 1 can be received.
These signals are transmitted, for example, by a pay TV
decoder, game machine or photo CD unit, etc.
If both Euro scart 1, and 2 sockets have been connected to the
VCRs simultaneously, only the AV 2 can be received.
If the S-VHS signal is received through the S-VIDEO, you must
change to the S-Video mode.
In Euro scart 2 socket, the video output is not available.
Signal type RGB,
Audio/Video in sockets
1.
3
2.
3.
VCR
Connect the audio/video out sockets of the VCR to audio/video
in sockets of the set.
Press the TV/AV button to select AV3 (option).
Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
Note : If you have a mono VCR, connect the audio cable from the
VCR to the AUDIO L/MONO socket of the set.
27
ENGLISH
Connection of external
S-Video/Audio in sockets
When
connecting
picture quality will
1.
equipment
(S-Video) (option)
S-VIDEO VCR to the S-VIDEO
be further improved.
an
socket, the
Connect the S-Video socket of the VCR to the S-VIDEO socket of the set.
2.
Connect the audio cable from the S-VIDEO VCR to the AUDIO
3.
sockets of the set.
Select S-Video by
4.
Press the PLAY button
The VCR
DVD
1.
pressing
on
playback picture
the TV/AV button
S-VIDEO VCR
repeatedly.
3
the VCR.
on
appears
the
screen.
input sockets (option)
Connect the DVD
output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y
orYPBPR)oftheDVDtotheDVDINPUTsockets(YPBPR)of
S-VIDEO VCR
the set.
2.
Connect the audio cable from the DVD to DTV/DVD INPUT
3.
AUDIO sockets of the set.
Press the TV/AV or MULTIMEDIA button to select
4.
Press the PLAY button
The DVD
playback picture
Headphone
Insert the
can
listen
on
socket
/
Component.
P
the DVD.
appears
on
the
screen.
(option)
S-VIDEO VCR
headphone plug to the headphone socket of the set. You
to the sound through the headphone. To adjust the head-
press the F / G button. If you press the MUTE button, the sound from the headphone is switched off.
phone volume,
S-VIDEO VCR
/
P
DVD
28
Connection of PC
PC in socket
2.
3.
4.
Displayable
Monitor
Connect the signal cable (DVI-D cable, Not DVI to D-Sub
cable) from the DVI output socket of the PC to the DVI input socket of the set when using a PC with DVI output.
In some video cards, DVI-Analogue output may not be supported.
Note
:
Specification
* 15"~30"
MODE
(option)
Connect the signal cable from the monitor output socket of the
PERSONAL COMPUTER to the PC input socket of the set.
Connect the audio cable from the PC to the PC SOUND sockets of the set.
Press the TV/AV or MULTIMEDIA button to select PC.
Switch on the PC, and the PC screen appears on the set.
The set can be operated as the PC monitor.
1.
PERSONAL COMPUTER
(option)
* 32"
Horizontal
Resolution
Vertical
MODE
Resolution
Frequency(kHz) Frequency(Hz)
640x480
VGA
SVGA
XGA
WXGA
31.4
35.0
67
640x480
37.5
75
800x600
35.1
56
800x600
37.8
60
800x600
48.0
72
800x600
46.8
75
1024x768
48.3
60
1024x768
56.4
70
1024x768
60.0
75
1280x768
47.6
(option)
60
1280x720
44.7
(option)
60
form
Vertical
Frequency(kHz) Frequency(Hz)
60
640x480
(Synchronization input
Horizontal
:
VGA
640x480
31.4
60
SVGA
800x600
37.8
60
XGA
1024x768
48.3
60
1280x768
47.6
60
1360x768
47.6
60
WXGA
separate)
Note :
If the set is cold, there may be a small "flicker" when the set is switched on. This is normal, there is
a.
nothing wrong with the set.
b. If possible, use the VESA 1024x768@60Hz (15") / 1280x768@60Hz (17", 23"~30") /
1360x768@60Hz (32") video mode (for 27 inch LCD monitor only, VESA 1280x720@60Hz; In
some video cards, this mode may not be supported.) to obtain the best image quality for your LCD
monitor. If used under the other resolutions, some scaled or processed pictures may appear on the
screen.
The set has been pre-adjusted to the mode VESA 1024x768@60Hz (15") /
1280x768@60Hz (17", 23"-30") / 1360x768@60Hz (32") (for 27 inch LCD monitor only, VESA
1280x720@60Hz).
c.
d.
e.
f.
Some dot defects may appear on the screen, like Red, Green or Blue spots. However, this will have
no impact or effect on the monitor performance.
Do not press the LCD screen with your finger for a long time as this may produce some temporary
distortion effects on the screen.
When the PC screen appears on the set, a message may appear on the screen, and the message
will differ according to the Window system version. If a message appears click "Next" until the message finishes.
If the message "out of Range" appears on the screen, adjust the PC as in the 'Displayable Monitor
Specification' section.
DPM (Display Power Management) mode
When the PC is in the power saving mode, automatically the monitor goes into DPM mode to
energy.
Note : Use the supplied signal cable with the set. Otherwise, DPM mode may not work.
save
the
29
ENGLISH
Connection of PC
PC
(option)
PC
Setup (only DVI-Analogue mode) (option)
H-Position
V-Position
You
adjust horizontal/vertical position, clock, phase,
configure, reset as you prefer.
can
and auto-
Clock
Phase
Auto
Configure
Reset
1.
Press the MENU button and then D / E button to select the
Setup
2.
3.
4.
DEFG
menu.
OK
MENU
Press the G button and then D / E button to select Input.
Press the G button and then D / E button to select PC.
Press the MENU button and then D / E button to select the PC
menu.
PC
87
H-Position
V-Position
Clock
Phase
Auto
TV/AV
Configure
Reset
MENU
DEFG
5.
6.
OK
MENU
Press the G button and then D / E button to select the desired
picture item.
Press the F / G button to make appropriate adjustments.
OK
H-Position / V-Position
This function is to
adjust picture
PR
VOL
to
left/right
and
up/down
as
you
prefer.
VOL
PR
Clock
This function is to minimize any vertical bars or stripes visible on
the screen background. And the horizontal screen size will also
change.
Phase
This function allows you to remove any horizontal noise and
clear or sharpen the image of characters.
Auto-configure
This function is for the automatic
adjustment of the screen position, clock and phase. The displayed image will disappear for a
few seconds while the Auto-configuration is in progress.
Reset
This function allows you to return to the good picture reproduction programmed at the factory and cannot be changed.
Note : Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor's position, clock and phase manually.
7.
8.
30
Press the OK button to store it for the PC monitor
Press the TV/AV button to return to PC mode.
picture.
?
External Control Device
-
Connect the RS-232C
trol
-
-
system)
input jack
an
(such
as a
(option)
computer
or an
A/V
con-
externally.
port of the control device
RS-232C connection cable is not
Setup
external control device
and control the TV's functions
Connect the serial
RS-232C
to
; RS-232C
to the RS-232C
jack
on
the TV back
panel.
with the TV.
supplied
Setup
PC
Type
of
Connector; D-Sub 9-Pin Male
1
No.
Pin
1
No connection
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
name
5
(Receive data)
(Transmit data)
(DTE side ready)
(DCE side ready)
(Ready to send)
(Clear to send)
9
6
No Connection
9
RS-232C
Configurations
3-Wire
Configurations
(Not standard)
7-Wire
Configurations
(Standard RS-232C cable)
PC
TV
PC
TV
RXD
3
TXD
RXD
2
3
TXD
TXD
2
RXD
TXD
3
2
RXD
5
GND
GND
5
5
GND
6
DSR
DTR
4
4
DTR
4
DTR
DSR
6
6
DSR
8
CTS
RTS
7
7
RTS
7
RTS
CTS
8
8
CTS
GND
DTR
DSR
RTS
CTS
2354678
D-Sub 9
D-Sub 9
D-Sub 9
D-Sub 9
31
ENGLISH
External Control Device
; RS-232C
Setup
(option)
Communication Parameters
?
Baud rate
?
Data
?
:
9600
bps (UART)
length : 8
Parity : None
bits
Use
(reverse)
*
a
crossed
?Stopbit:1bit
?
Communication code
cable.
Command Reference List
Transmission /
COMMAND COMMAND
2
1
01. Power
ASCII code
:
k
a
(Hexa)
Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
0~1
*
[Command 1]: First command. (j or k)
[Command 2]: Second command.
[Set ID]: You can adjust the set ID to choose desired monitor
ID number in Special menu. Adjustment range is 1
99. When selecting Set ID '0', every connected
Input Select
Aspect Ratio
k
k
c
04. Screen Mute
k
d
0~1
05. Volume Mute
k
e
0~1
06. Volume Control
k
f
0~64
TV set is controlled. Set ID is indicated
07. Contrast
k
g
0~64
08.
k
h
0~64
(1~99)on menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
02.
03.
b
DATA
Receiving
*
*
Brightness
0~4
*
~
*
09. Color
k
i
0~64
10. Tint
kj0~64
11.
k
k
0~64
k
l
0~1
k
m
0~1
14. Balance
k
t
15. Tune Command
m
16. Add/Delete
17.
Sharpness
12. OSD Select
13.
*
:
Key
Lock
Key
Refer to '02.
Input
[DATA]:
Transmit 'FF' data to read status of command.
*
[Cr]: Carriage
Return
ASCII code '0x0D'
*
[
]:
ASCII code
'space (0x20)'
0~64
OK Acknowledgement
mb
0~1
[Command2][ ][Set ID][ ][OK][Data][x]
m
Key
Select'
on
c
decimal
To transmit command data.
0~63
a
as
Code
*
page 33
The Monitor transmits ACK
(acknowledgement)
this format when
normal data. At this
receiving
based
on
time, if the
data is data read
mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
*
The Monitor transmits ACK
(acknowledgement)
this format when
abnormal data from non-viable
functions
32
or
receiving
communication
errors.
based
on
External Control Device
01. Power On
You
mute on/off.
adjust
mute
Power Off
1
:PowerOn
Data
0
:
Volume mute off
1
:
Volume mute
(Volume on)
(Volume off)
on
G To show Power On/Off.
Acknowledgement
Transmission
[e][ ][Set ID][ ][OK][Data][x]
[k][a][ ][Set ID][ ][FF][Cr]
06. Volume Control
Acknowledgement
Power Off
(Command:f)
G To adjust volume.
[a][ ][Set ID][ ][OK][Data][x]
:
on
[k][e][ ][Set ID][ ][Data][Cr]
[a][ ][Set ID][ ][OK][Data][x]
0
the MUTE button
Transmission
Acknowledgement
Data
using
remote control.
[k][a][ ][Set ID][ ][Data][Cr]
:
also
can
(option)
(Command:e)
G To control volume
Transmission
0
Setup
05. Volume Mute
(Command:a)
G To control Power On/Off of the TV.
Data
; RS-232C
You
1
adjust
volume with the volume buttons
remote control.
on
:PowerOn
also
can
Transmission
02.
Select
Input
G To select input
You
source
also select
can
ton
(Command:b) (Main
an
Picture
Input)
for the TV.
input
Data
using
source
the TV/AV but-
Min:0~Max:64
?
Refer to 'Real data
mapping
the TV's remote control.
on
10
:TV
20
:AV1orAV
21
:
AV2
30
:
S-Video
40
(option)
:
Component
Component
Component
41
:
60
:PC
1
2
07. Contrast
(option)
G To adjust
You
(Command:g)
screen
also
can
contrast.
adjust
contrast in the Picture
Transmission
[b][ ][Set ID][ ][OK][Data][x]
[k][g][ ][Set ID][ ][Data][Cr]
Data
Ratio
G To adjust the
You
(Command:c) (Main picture format)
screen
adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control.
Transmission
0
:
Normal
1
:
Wide
In PC mode
only
3:Zoom
(4:3)
(16:9)
4:Auto
1'
as
shown below.
Brightness (Command:h)
also
can
brightness.
adjust brightness
screen
in the Picture
menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
16:9 and 4:3
aspect ratios
Acknowledgement
are
available.
Data
Min:0~Max:64
?
Refer to 'Real data
mapping
1'
as
shown below.
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
04. Screen Mute
(Command:d)
G To select
mute on/off.
screen
mapping
[g][ ][Set ID][ ][OK][Data][x]
You
2:14:9
*
Refer to 'Real data
G To adjust
screen
screen
Min:0~Max:64
?
08.
[k][c][ ][Set ID][ ][Data][Cr]
Data
menu.
Acknowledgement
format.
also
can
shown below.
or
Acknowledgement
Aspect
as
[f][ ][Set ID][ ][OK][Data][x]
[k][b][ ][Set ID][ ][Data][Cr]
03.
1'
Acknowledgement
Transmission
Data
[k][f][ ][Set ID][ ][Data][Cr]
[h][ ][Set ID][ ][OK][Data][x]
*
Real data
0
mapping
1
:Step0
Transmission
A:Step10
[k][d][ ][Set ID][ ][Data][Cr]
Data
0
:
Screen mute off
1
:
Screen mute
on
(Picture on)
(Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
F
:Step15
10:Step16
64
:
Step
100
*Tint:-50~+50
33
ENGLISH
External Control Device
09. Color
You
can
Setup
(Command:i)
G To adjust the
also
15. Tune Command
color.
screen
G Tune channel
color in the Picture
adjust
; RS-232C
to
menu.
(Command:m a)
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
[m][a][ ][Set ID][ ][Data0][ ][Cr]
Data
Data0:
?
Refer to 'Real data
Min
1'. See page 33.
mapping
0
:
number.
following Physical/major/minor
Transmission
Min:0~Max:64
(option)
Programme Number
Max : 63(transmit by
~
Hexadecimal
code)
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
Acknowledgement
10. Tint
[a][ ][Set ID][ ][OK][Data0][x]
[a][ ][Set ID][ ][NG][Data0][x]
(Command:j)
G To adjust the
You
can
tint.(NTSC
screen
also
adjust
M
input only)
tint in the Picture
menu.
Transmission
16.
[k][j][ ][Set ID][ ][Data][Cr]
G To skip the
Data
Transmission
:Green0~Red :64
?
Refer to 'Real data
mapping
1'. See page 33.
Skip
programme
(Command:m b)
current programme.
[m][b][ ][Set ID][ ][Data 0][Cr]
Acknowledgement
Data0:
[j][ ][Set ID][ ][OK][Data][x]
(Programme)Skip on-0, (Programme)Skip
off-1
Acknowledgement
11.
Sharpness (Command:k)
G To adjust the
You
can
sharpness.
adjust sharpness in
[b][ ][Set ID][ ][OK][Data0][x]
[b][ ][Set ID][ ][NG][Data0][x]
screen
also
the Picture
menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
17.
Data
G To send IR
Min: 0
?
~
Max: 64
Refer to 'Real data
mapping
1'. See page 33.
Key (Command:m c)
key
code.
Transmission
Acknowledgement
[m][c][ ][Set ID][ ][Data][Cr]
[k][ ][Set ID][ ][OK][Data][x]
Data:
12. OSD Select
remote
(Command:l)
G To select OSD (On Screen Display)
Key
code
Acknowledgement
mute on/off.
[c][ ][Set ID][ ][OK][Data][x]
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data
0: OSD mute
1: OSD mute off
on
code
Acknowledgement
Key
[l][ ][Set ID][ ][OK][Data][x]
Function
Code
Function
Code
MUTE
09
SSM
52
POWER
08
PSM
4D
LIST
53
SLEEP
0E
Q.VIEW
1A
ARC
79
MENU
43
TEXT
20
PR+
00
UPDATE
62
PR-
01
SIZE
64
Acknowledgement
VOL+
02
HOLD
65
[m][ ][Set ID][ ][OK][Data][x]
VOL-
03
INDEX
70
OK
44
TIME
26
11
MIX
24
12
REVEAL
2A
13
MODE
22
14
BLUE
61
15
YELLOW
63
16
GREEN
71
17
RED
72
18
TV/AV
0B
19
TV/PC
98
10
I/II
0A
13.
Lock
Key
G To lock the
(Command:m)
remote control and the front
panel
controls
on
the TV.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data
?
If
0: Lock off
1: Lock
on
the remote control and front panel controls
on the TV, use this mode. When main power is on/off,
remote control lock is released.
you're
not
14. Balance
using
(Command:t)
G To adjust balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
Min: 0
~
Max: 64
(transmit by
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
34
Hexadecimal
code)
1234567890
Troubleshooting
check list
ENGLISH
Symptoms
No
picture,
no
Sound
sound
OK, poor picture
Picture
OK, poor sound
Picture blurred
Lines
or
streaks in
Poor
picture
reception
on some
channels
No colour
Poor colour
Remote control does not work
Incorrect
position
Vertical bars
or
stripes
on
background
Horizontal noise
Signal
Cable message appears
Check these items and try to
adjust these
The mains plug-(plugged in and
switched on)
Is the TV switched
Try
on
another channel
(weak signal)
Check aerial
(plugged
into
Check aerial
(broken lead?)
TV?)
Check aerial
Check for local interference
Adjust
contrast
Adjust brightness
Adjust
colour
Adjust
volume
Check the batteries in remote control
Check Audio/Video sockets
Auto-configure
or
adjust
(VCR only)
the H/V
Auto-configure
or
adjust
Clock
Auto-configure
or
adjust
Phase
Is the
Signal
Cable connected
position
or
loose
35
Download PDF

advertising