advertisement
▼
Scroll to page 2
of 40
LCD TV OWNER'S MANUAL MODELS: RZ-23LZ25*** RZ-23LZ55*** RZ-26LZ55*** RZ-32LZ55*** Please read Information Manual included together before reading this manual and operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached and quote this information to your dealer when you require service. on the back P/NO : cover 38289U0016B (0507-REV01) Printed in Korea Contents Installation 3 Location and function of controls Remote control handset Battery installation / Front/ Rear 5 Basic operation On and off / Programme selection Volume adjustment / Quick view Mute function On screen language selection 10 On 11 screen menus Menu selection 12 up TV stations Auto programme tuning Manual programme tuning Setting Assigning a Programme station edit name Favourite programme Calling the programme table Picture adjustment PSM (Picture Status Picture adjustment Picture format 17 Memory) Sound 19 Time Menu Clock / On/Off time Auto off / Sleep timer 21 Other functions 23 adjustment SSM (Sound Status Memory) Sound adjustment / Stereo/ Dual reception NICAM reception/ Sound output selection TV, AV and PC modes Auto AV switching / Child lock Teletext Switch on/off SIMPLE text / TOP text FASTEXT / Special teletext functions 25 Connection of external 28 equipment Aerial socket Euro scart socket (VCR) / S-Video/Audio in sockets (S-Video) Euro scart socket (DVD) DVD input sockets (RZ-23LZ55***/ RZ-26LZ55***/ RZ-32LZ55***) Audio/Video in sockets (RZ-23LZ25*** only) Connection of PC PC in socket PC Setup (only 30 DVI-Analogue mode) External Control Device Troubleshooting How to the set 2 Setup; RS-232C 32 36 check list join the product assembly tumbling to the wall to protect 38 Installation ENGLISH Warning To prevent fire or Matrix LCD with shock hazard, do anything hard as not expose the set to rain this may scratch, mar, or or moisture. Do not rub damage or strike the Active the Active Matrix LCD permanently. Service Never remove set does not the back cover of the set operate properly, unplug this expose you to it and call your dealer. as can high voltage and other hazards. If the Location Position your set so that no bright light or not to expose the set to any unnecessary sunlight falls directly onto the vibration, moisture, dust placed in a position to allow a free flow of air. Do not cover This standing angle can be adjusted as shown in pictures. or screen. heat. Also the ventilation Care should be taken ensure openings on that the set is the back cover. If you intend to mount the TV to a wall, attach VESA standard mounting interface (optional parts) to the back of the TV. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop. Cleaning the set before cleaning the face of the LCD Screen. Dust the set by wiping the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, Unplug not On use liquid cleaners or and the cloth. Do screen damp aerosol cleaners. Disposal The fluorescent product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product mute be carried out in accordance to the regulations of lamp used in this your local authority. 3 Installation Connection of TV 12 Pull the back cover backside while pushing the two tabs and then lift it up. Connect the aerial cable to the socket marked +75 Ω on the back. For the best reception an outdoor aerial should be used. 345 To connect an additional equipment, see the Connection of external equipment Connect the power cord. Close the back cover. Note: Here shown may be somewhat different from your set. 24 1 ~ 5 Positioning your display Adjust ? the position of the panel in various ways for maximum comfort. Tilt range RZ-23LZ55*** RZ-23LZ25*** 3 12 5 EO SVD EO -VD S VIDEO DEO V NO O LMO AUDO A3 ? UDO A R AV3 Swivel range The TV left 4 L/MON or can right be to R (RZ-23LZ25*** only) conveniently swiveled on its stand provide the optimum viewing angle. 25° to the 15 section. Location and function of controls All the functions can Some functions panel of the set. can operate this be controlled with the remote control handset. also be adjusted with the buttons on the side Only the remote control handset supplied will set. Remote control handset 10 MUTE POWER 1 11 TV/AV MULTIMEDIA I/II Before you use the remote control batteries. See the next page. 1. 12 2 LIST 13 OK VOL TV/AV selects TV or AV monitor mode. clears the menu from the screen. switches the set on from standby. VOL 3. LIST the programme table. displays PR 4. Q.VIEW returns to the 123 selects 5. 456 D / E programme or a menu item. switches the set on from standby. 789 78 SLEEP 0 ARC PSM (Volume Down/Up) adjusts the volume. adjusts menu settings. 14 OK TEXT accepts your selection 15 SIZE MIX HOLD REVEAL NUMBER BUTTONS switches the set on from 7. SSM 8. ARC ? i or the current mode. displays TIME 6. INDEX a F / G 9 UPDATE a viewed programme. favourite programme. previously (Programme Up/Down) selects SSM off. 2. PR 6 on or Q.VIEW MENU 34 5 MUTE switches the sound handset, please install the standby and selects a programme. (Sound Status Memory) recalls your preferred sound setting. MODE M select your desired 9. picture format. SLEEP sets the sleep timer. 10. MULTIMEDIA selects: TV, COMPONENT(RZ-23LZ55***/ RZ-26LZ55***/ RZ-32LZ55***) or PC mode. 5 ENGLISH Location and function of controls 11. POWER switches the set on from standby 12. I/II selects the language during dual selects the sound output. or off to standby. language broadcast. 13. MENU selects 10 a menu. MUTE 14. PSM (Picture Status recalls your preferred 1 Memory) picture setting. : 11 TV/AV MULTIMEDIA 12 LIST 34 PR COLOURED BUTTONS models) Q.VIEW MENU 13 No function TELETEXT I/II 2 15. TELETEXT BUTTONS These buttons are used for teletext. For further details, see the 'Teletext' section. * POWER or : These buttons are used for teletext (only 5 programme edit. OK VOL VOL PR Battery installation 123 The remote control handset is powered by two AAA/Alkaline type batteries. To load the the remote control batteries, turn handset over and open the battery compartment. Install two batteries as indicated by the polarity symbols ( + and ) - marked inside the compartment. Note : To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time. 6 456 789 78 SSM SLEEP ARC PSM 14 TEXT 9 15 UPDATE TIME SIZE MIX HOLD REVEAL ? INDEX i 6 0 MODE M Location and function of controls ENGLISH Front * : The mark consists of blank or alphabet. RZ-23LZ25*** Side panel 7 6 5 R 9 43 8 1 10 RZ-23LZ55*** / RZ-26LZ55*** / RZ-32LZ55*** Side panel PR 7 VOL 6 OK 5 MENU 4 TV AV/PC 2 1 8 10 1. ON/OFF( 9 /I) switches the set on from standby or (Volume Down/Up) adjusts the volume. adjusts menu settings. 7. D / E off to standby. 2. TV/AV/PC selects TV, AV clears the or menu switches the set 3. clears the or from screen. standby. AV monitor mode. menu switches the set from the on from screen. 8. REMOTE CONTROL SENSOR 9. POWER/STANDBY INDICATOR illuminates red in standby mode. ( ) illuminates green when the set is switched standby. on. MENU selects 5. programme or a menu item. switches the set on from standby. a TV/AV selects TV 4. on (Programme Up/Down) selects PC monitor mode. from the F / G 6. 10. Stand a menu. (option) OK accepts your selection or displays the current mode. 7 Location and function of controls Rear RZ-23LZ25*** S-VIDEO INPUT VIDEO INPUT AUDIO INPUT PC SOUND INPUT DVI INPUT (RGB INPUT) ANTENNA EURO SCART1/2 RS-232C JACK REMOTE CONTROL JACK AC INPUT 8 SOCKET INPUT Location and function of controls ENGLISH Rear RZ-23LZ55*** / RZ-26LZ55*** / RZ-32LZ55*** RZ-26LZ55*** RZ-23LZ55*** RZ-32LZ55*** S-VIDEO INPUT COMPONENT IN (576i/576p/720p/1080i) COMPONENT DVD IN (576i/576p/720p/1080i) AUDIO INPUT PC SOUND INPUT DVI INPUT (RGB INPUT) ANTENNA EURO SCART1/2 RS-232C JACK INPUT SOCKET REMOTE CONTROL JACK AC INPUT 9 Basic operation On and off 1. Press the POWER, D / E, buttons to switch it on fully. 2. Press the POWER button. The set reverts to Pull out mains plugs to switch the set off. 3. Note MUTE POWER : If, while the TV/AV MULTIMEDIA set is switched on, the mains the set will switch to replaced TV/AV, MULTIMEDIA standby or power in the mains power socket. on or NUMBER standby plug is mode. disconnected when the mains plug is I/II Programme selection You a Q.VIEW MENU can select programme number with the D / E or NUMBER buttons. PR Volume OK VOL VOL adjustment Press the F / G button to PR adjust the volume. Quick view 123 Press the Q.VIEW button to view the last programme you 456 789 SSM were watching. Note : This function works only when Favourite programme is set to Off. Otherwise each press of this button will select a stored favorite programme. 0 Mute function Press the MUTE button. The sound is switched off and the display appears. You can cancel it button. On screen The menu can First select 1. 3. language be the MUTE, F / G, I/II,orSSM selection displayed your language. on the screen in your desired Press the MENU button and then D / E Setup 2. by pressing language. button to select the menu. Press the G button and then D / E button to select Language. Press the G button and then D / E button to select your desired language. All the 10 on screen displays will appear in the selected 4. Press the OK button. 5. Press the TV/AV button to return to normal TV language. viewing. On ENGLISH screen menus Menu selection 2. Press the MENU button and then D / E button to display each menu. Press the G button and then D / E button to select a menu item. 3. Change 1. the setting of an item in the sub or pull-down menu with F / G button. You can move to the button and to move higher level by pressing the OK level menu by pressing menu to the lower MENU button. Note : In the TV/AV, a. b. c. the COMPONENT(RZ-23LZ55***/ RZ-26LZ55*** RZ-32LZ55***) mode, the PC menu is not displayed. In the teletext mode, menus are not displayed. On some models, the Language will not be displayed. / MENU Picture Channel Auto programme PSM Manual programme Contrast Programme edit Brightness Favourite programme Colour PR OK VOL Sharpness DEFG OK DEFG MENU Channel OK PR MENU Picture menu VOL menu Sound Setup SSM Language AVL Input Balance Child lock Set ID DEFG OK MENU Setup DEFG OK MENU Sound menu menu Time Time Off time On time Auto off DEFG OK MENU Time menu 11 Setting Channel TV stations up programme numbers (0 to 99). Once you have preset the stations, you will be able to use the D / E or NUMBER buttons to scan the stations you have programmed. Stations can be tuned using automatic or manual modes. Up Auto programme Manual programme Programme edit Favourite programme to 100 TV stations can Auto programme DEFG OK be stored by tuning All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set. MENU 1. 2. Press the MENU button and then D / E button to select the Channel menu. Press the G button and then D / E button to select Auto programme. Auto programme TV/AV System BG Storage from I Search DK L MENU M DEFG PR 3. OK VOL VOL PR 123 456 4. 5. 6. 789 7. 0 OK MENU Press the G button. Select a TV system with the G button and then D / E button on the System menu; BG : PAL B/G, SECAM B/G (Europe/East Europe) I : PAL I/II (U.K./Ireland) DK : PAL D/K, SECAM D/K (East Europe) L : SECAM L/L' (France) M : (USA/Korea/Philippines) Press the OK button. Press the D / E button to select Storage from. Select the beginning programme number with the F / G button or NUMBER buttons on the Storage from pull-down menu. Any number under 10 is entered with a numeric '0' in front of it, i.e. '05' for 5. Press the D / E button to select Search. Auto programme System Storage from Search C21 2 BG 5 % MENU 8. Press the G button to begin auto programming. All receivable stations are stored. The station name is stored for stations which broadcast VPS (Video Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If no station name can be assigned to a station, the channel number is assigned and stored as C (V/UHF 01-69) or S (Cable 01-47), followed by a number. To stop auto programming, press the MENU button. When auto programming is completed, the Programme edit menu appears on the screen. See the 'Programme edit' section to edit the stored programme. 9. 12 Press the TV/AV button to return to normal TV viewing. TV stations up Setting Manual programme tuning Channel Auto programme Manual programme Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station name with five characters to each programme number. 1. ENGLISH Press the MENU button and then D / E button to select the Channel menu. 2. Press the G button and then D / E button to select Manual 3. programme. Press the G button and then D / E button to select Programme edit Favourite programme DEFG OK MENU Storage. Manual programme 29 Storage System Channel TV/AV Search Name MENU DEFG 4. 5. 6. OK MENU Select the desired programme number (0 to 99) with the F / G button or NUMBER buttons on the Storage menu. Any number under 10 is entered with a numeric '0' in front of it, i.e. '05' for 5. Press the D / E button to select System. Select a TV system with the G button and then F / G button the System menu; BG : PAL I : DK : PAL I/II (U.K./Ireland) PAL D/K, SECAM D/K L : M : OK on VOL PR (East Europe) 123 SECAM L/L' (France) (USA/Korea/Philippines) 456 Press the OK button. 8. Press the D / E button to select Channel. Press the G button and then D / E button to select VHF/UHF Cable on the Channel menu. If possible, select the channel number directly buttons. Any number under 10 is entered with front of VOL B/G, SECAM B/G (Europe/East Europe) 7. 9. PR or with the number a numeric '0' in 789 0 it, i.e. '05' for 5. 10. Press the OK button. 11. Press the D / E button to select Search. 12. Press the G button and thenF / G button to on the Search pull-down menu. If a commence searching station is found the search will stop. Manual programme Storage System Channel Search GGG Name DEFG OK MENU 13. Press the OK button to store it. 14. To store another station, repeat steps 3 to 13. 15. Press the TV/AV button to return to normal TV viewing. 13 Setting Assigning a station name 1. Repeat the 'Manual programme tuning' steps Channel Auto programme Manual programme Programme TV stations up 3. Press the G button and then D / E button to select Name. Press the G button and then use the D / E. You can use a blank, 4. -,thenumber0to9andthealphabetAtoZ. With the F button you can select in the opposite direction. Select the position by pressing the F / G button and then 5. your choice of the second character, and Press the OK button to store it. 6. Press the TV/AV button to return to normal TV 2. edit Favourite programme 1 to 2. +, DEFG OK MENU TV/AV MENU PR OK VOL VOL PR 14 so on. viewing. make Setting Programme TV stations up Channel edit Auto programme Manual programme This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or insert a blank station data into the selected programme number. 1. Press the MENU button and then D / E button to select the Channel menu. 2. Press the G button and then D / E button to select edit. Programme 3. Press the G button to menu. display the 0C0 35S Deleting ENGLISH Programme edit 6S17 2C1 2 7----- 3S6 6 8----- 4S6 7 9----- Copy Move Skip Favourite programme DEFG OK MENU 69 1BLN03 Delete Programme edit TV/AV MENU a 1. programme Select a programme to be deleted with the D / E 2. Press the RED button twice. The selected programme is deleted, all the programmes are shifted up one position. F / G button. or following PR OK VOL 0C035S 69 1BLN03 6S17 2C1 2 7----- 3S66 8----- 4S67 9----- VOL PR 123 Delete 456 Copying a 1. programme Select a programme to be 2. Press the GREEN button. All the Moving following copied programmes with the D / E are shifted down or F / G button. one position. 789 0 a 1. programme Select a programme to be moved with the D / E 2. Press the YELLOW button. 3. Move the programme to the desired programme number with or F / G button. theD/EorF/Gbutton. 4. Press the YELLOW button Skipping 1. Select a a again programme number programme number to be to release this function. skipped with the D / E or F / G button. 2. 3. Press the BLUE button. The programme turns to blue. Press the BLUE button again to release the skipped programme. When a programme number is skipped it means that you will be unable to select it using the D / E button during normal TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu. skipped Press the TV/AV button to return to normal TV viewing. 15 TV stations up Setting Favourite programme Channel Auto programme This function lets you select your favourite programmes Manual programme Programme edit Favourite programme directly. 1. Press the MENU button and then D / E button to select the Channel menu. 2. Press the G button and then D / E to select Favourite programme. DEFG OK MENU Favourite programme On -- ----- -- ----- -- ----- -- ----- -- ----- -- ----- -- ----- -- ----- DEFG 3. TV/AV 4. 5. LIST Q.VIEW MENU 6. 7. -- or Off. ----- . the Q.VIEW button to select stored favourite programmes. OK VOL MENU Press the G button and then F / G button to select On Press the D / E button to select Select a desired programme with the F / G button. To store another programme, repeat steps 4 to 5. You can store up to 8 programmes. Press the TV/AV button to return to normal TV viewing. Repeatedly press PR OK VOL PR Calling You the programme table check the programmes stored in the memory the programme table. 123 456 can Displaying programme table Press the LIST button to display the by displaying Programme table menu. The programme table appears on the screen. One programme table contains ten programmes as below. 789 0C0 35S 6 9 1 0 BLN03 6S17 2C12 7 S22 3S66 8C09 4S67 9C11 Note : a. You may find some blue programmes. They have been set up to be skipped by auto programming or in the programme edit mode. b. Some programmes with the channel number shown in the programme table indicate there is no station name assigned. Selecting Select a programme in the programme table programme with the D / E Then press the OK button. a or F / G button. The set switches to the chosen programme number. Paging through There are a programme table 10 programme table pages in which contain 100 programmes. Pressing the D / E or F / G button repeatedly Press the TV/AV button to return to normal TV 16 turns the pages. viewing. Picture PSM 1. 2. 3. (Picture Status Memory) Picture Press the MENU button and then D / E Picture menu. PSM button to select the Contrast Brightness Colour Press the G button and then D / E button to select PSM. Press the G button and then D / E button to select a picture set- ting 4. ENGLISH adjustment on the PSM Sharpness menu. Press the OK button. DEFG OK MENU Picture PSM Dynamic Contrast Standard Brightness Mild Colour Game Sharpness User DEFG 5. OK MENU TV/AV Press the TV/AV button to return to normal TV viewing. MENU picture (Dynamic, Standard, Mild, Game or User) with PSM button on the remote control. The picture Dynamic, Standard, Mild and Game are programmed for optimum picture reproduction at the factory and cannot be changed. You can also recall a desired PR Picture You adjustment OK adjust picture contrast, brightness, sharpness to the levels you prefer. 1. can colour Press the MENU button and then D / E Picture menu. intensity, VOL VOL PR button to select the Picture PSM Contrast 47 Contrast Brightness Colour Sharpness DEFG OK PSM MENU 3. Press the D / E button to select the desired Press the F / G button to make appropriate 4. Press the TV/AV button to return to normal 2. Note : Only Contrast and Brightness are picture item. adjustments. TV viewing. displayed in PC mode. 17 Picture adjustment Picture format You watch TV in various can Spectacle, Original, 4:3. Repeatedly press the ARC picture formats; 16:9, 14:9, Zoom, button to select your desired picture format. 16:9 You enjoy the cinema (the picture format of 16:9) or general programme through the 16:9 mode. The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and right so that the screen 16:9 is full. can TV 14:9 You TV/AV the picture format of 14:9 the 14:9 mode. can through The MENU enjoy screen 14:9 is viewed to the upper / lower and just like left / right. or that the TV programme general screen 4:3 is magnified Zoom You The PR so OK VOL VOL PR the cinema in a vast screen through the Zoom mode. screen 4:3 is magnified to the upper / lower and left / right sides that the screen 16:9 is full. The bottom and top of the picture can enjoy may be lost. Spectacle When your TV receives the wide adjust the picture horizontally, in entire signal, it will lead nonlinear proportion, to screen a you to fill the screen. Original When your TV receives the wide screen signal, it will be changed to the picture format to be sent. automatically 4:3 This ARC 18 picture Note : format is 4 to 3 of In PC mode only general 16:9 and 4:3 TV. aspect ratios are available. Sound SSM You (Sound Memory) Sound SSM select your preferred sound setting; Flat, Music, Movie or and you can also adjust the sound frequency of the equalizer. can Speech 1. Status ENGLISH adjustment AVL Balance Press the MENU button and then D / E button to select the Sound menu. Sound SSM Flat AVL Music Balance Movie DEFG OK MENU Speech G User DEFG 2. 3. OK MENU Press the G button and then D / E button to select SSM. Press the G button and then D / E button to select a sound setting on the SSM menu. Sound TV/AV Frequency Adjustment Press the OK button in User. b. Select a sound band by pressing the F / G button. c. Make appropriate sound level with the D / E button. d. Press the OK button to store it for the sound User. a. MENU PR OK VOL VOL PR 0.1 0.5 1.5 5 10Khz Press the TV/AV button to return to normal TV You viewing. also recall a desired sound setting (Flat, Music, Movie, Speech or User) with SSM button on the remote control. The sound settings Flat, Music, Movie and Speech are programmed for optimum sound reproduction at the factory and cannot be changed. can If you press the SSM button after making appropriate adjustment on the User sub menu, the display User automatically appears even though you have already set a factory preset setting; Flat, Music, Movie or Speech. Note : SSM Sound SSM DEFG Sound AVL On Balance Off OK MENU adjustment You can adjust balance, AVL AVL automatically keeps on change 1. 2. 3. (Auto Volume Leveler). an equal volume level even if you programmes. Press the MENU button and then D / E button to select the Sound menu. Press the G button and then D / E button to select the desired sound item; AVL or Balance. Make desired adjustment with the F / G, D / E and then press the OK button. 4. Press the TV/AV button to return to normal TV viewing. 19 Sound adjustment Stereo/Dual When reception programme is selected, the sound information for the station appears after the programme number and station name a disappear. I/II Broadcast On Screen Mono MONO Stereo STEREO Dual DUAL I Display Mono sound selection In stereo reception if the stereo signal is weak, you can switch to mono by pressing the I/II button twice. In mono reception the depth of sound is improved. To switch back to stereo, press the I/II button twice again. selection for dual language broadcast If a programme is received in two languages (dual language), you can switch to DUAL I, DUAL II or DUAL I+II by pressing the I/II button repeatedly. DUAL I sends the primary broadcast language to the loudspeakers. DUAL II sends the secondary broadcast language to the Language OK loudspeakers. DUAL I+II sends NICAM a separate language to each loudspeaker. reception If your set is equipped with the receiver for NICAM reception, the Companding Audio high quality NICAM (Near Instantaneous Multiplex) digital sound can be received. Sound output can be selected according to the type of received broadcast as follows by pressing the I/II button repeatedly. 1. When NICAM or 2. mono is received, you can FM MONO. When NICAM is stereo received, you STEREO or FM MONO. If the stereo FM mono. 3. select NICAM MONO When NICAM dual is NICAM DUAL II mono or is selected the can signal is select NICAM weak, switch to select NICAM DUAL I, NICAM DUAL I+II or MONO. When FM received, you display can MONO appears on the screen. Sound output selection In AV mode, you can select output sound for the left and right loudspeakers. press the I/II button to select the sound output. Audio signal from audio L input is sent to left loudspeaker and audio signal from audio R input is sent to right Repeatedly L+R L+L R+R 20 : : : loudspeaker. Audio signal from loudspeakers. Audio signal from loudspeakers. audio L input is sent to left and right audio R input is sent to left and right TIME Menu Clock ENGLISH Time Time You must set the time 1. using Off time on/off time function. Press the MENU button and then D / E TIME 2. correctly before On time button to select the Auto off menu. Press the G button and then D / E button to select TIME. Time DEFG OK MENU -i-i:i-i- Time Off time On time Auto off DEFG OK MENU 3. Press the G button and then D / E button to 4. Press the G button and then D / E button to 5. Press the MENU button to adjust the hour. adjust the minute. save. MENU On/Off time The off timer automatically switches the set to standby at the preset time. 1. Press the MENU button and then D / E TIME 2. PR button to select the menu. OK VOL Press the G button and then D / E button to select Off time or VOL PR On time. 3. Press the G button and then D / E button to select On. To cancel On/Off time function, press the D / E button to select Off. Time Time Off time On time -i-i:i-i- Auto off Pr. Vol. 0 30 On DEFG OK MENU 5. Press the G button and then D / E button to adjust the hour. Press the G button and then D / E button to adjust the minute. 6. Only 4. button to 7. function; Press the G button and then adjust volume level and programe number. On time Press the MENU button to Note save. : a. In the event of power interruption failure), the clock must be reset. b. Two hours after the set is switched will automatically switch back has been pressed. c. d. to (disconnection or power by the on time function it standby mode unless a button on Once the on or off time is set, these functions operate daily at the preset time. Off Timer function overrides On Timer function if they are set to the e. D / E same time. The set must be in standby mode for the On Timer to work. 21 TIME Menu Time Auto off Time Off time If you select On on the Auto off menu, the set will automatically switch itself to standby mode approximately ten minutes after a TV On time Auto off station DEFG OK MENU stops broadcasting. 1. Press the MENU button and then D TIME menu. 2. Press the G button and then D Press the G button and then D 3. / E button to select the button to select Auto off. E button to select On or Off. / E / Time Time Off time On time On Auto off Off MENU DEFG 4. OK VOL VOL PR MENU Press the MENU button to Sleep PR OK save. timer You don't have to remember to switch the set off before you go to sleep. The sleep timer automatically switches the set to standby after the preset time has elapsed. Press the SLEEP button to select the number of minutes. The display off' will appear on the screen, followed by 10, 20, 30, 60, 90, 120, 180 and 240. The timer begins to count down from ' the number of minutes selected. Note : a. To view the remaining sleep time, press the SLEEP button once. b. To cancel the sleep time, repeatedly press the SLEEP button off' appears. until the display When you switch the set off, the set releases the preset sleep time. ' SLEEP 22 c. Other functions TV, AV and PC modes ENGLISH Setup Language Inputs be set for can AV TV, video cassette recorder or (VCR), PC mode. AV mode is used when other or Input a Child lock is connected to equipment Set ID the set. Note : When a VCR is connected via the aerial socket the set is used in TV mode. See the 'Connection of external equipment' section. 1. 3. OK MENU Press the MENU button and then D / E button to select the Setup 2. DEFG menu. Press the G button and then D / E button to select Input. Press the G button and then D / E button to select TV, AV1, AV2, AV3, S-Video, Component or PC. The AV and PC modes are : TV/AV Setup RZ-23LZ25*** Language MENU Input TV Child lock AV1 Set ID AV2 AV3 S-video PC PR DEFG OK MENU OK VOL VOL Setup RZ-23LZ55*** RZ-26LZ55*** RZ-32LZ55*** PR Language Input TV Child lock AV1 Set ID AV2 123 S-video Component PC 456 DEFG OK MENU AV 1 : VCR connected to the Euro scart AV 2 : VCR connected to the Euro scart socket(1) socket(2) of the set. of the set. AV 3 : VCR connected to the AV3 of the set. S-Video : VCR connected to the S-Video of the set. Component : 789 DVD connected to the DVD IN sockets on 0 the back of set. PC : PERSONAL COMPUTER connected to the PC socket of the set. 4. Press the TV/AV button to return to normal TV Alternatively you TV/AV button. In AV mode, Auto AV can select the TV to return to TV or viewing. AV mode mode, press the D / E or by pressing the NUMBER buttons. switching If your VCR outputs an AV switching voltage when connected to the Euro scart socket, the set will switch to AV1 mode automatically. But if you want to keep NUMBER buttons. on watching TV mode, press the D / E or Press the TV/AV button to return to AV modes. 23 Other functions Child lock Setup Language Input The TV Child lock can be set so that the remote control handset is needed to control it. This feature Set ID can be used to prevent unauthorized view- ing. DEFG OK 1. MENU Press the MENU button and then D / E button to select the Setup 2. 3. menu. Press the G button and then D / E button to select Child lock. Press the G button and then D / E button to select On or Off on the Child lock menu. Setup Language Input Child lock On Set ID Off TV/AV MENU DEFG 4. OK VOL PR 24 MENU Press the TV/AV button to return to normal TV viewing. With the lock on, the display Child lock appears on the screen if any button on the side panel is pressed while viewing the TV. PR VOL OK Note : The display Child lock will not appear on the screen if any button on the panel is pressed while displaying the menus. Teletext Teletext (or TOP with the teletext Teletext is a text) is system an can optional function, therefore only a ENGLISH set receive the teletext broadcast. free service broadcast by most TV stations which gives information on news, weather, television programmes, share prices and many other topics. up-to-the-minute The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext) consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information. Switch on/off Press the TEXT button to switch to teletext. The initial page page appears on the screen. or last Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current page displayed. Press the TEXT button to switch off teletext. The previous PR OK mode PR reappears. SIMPLE text 123 selection Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then re-enter the correct page number. The D / E button can be used to select the preceding or Page 1. 2. following page. 456 789 0 TEXT colour button in LIST mode If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the M button to switch to LIST mode. Programming a Four teletext page numbers of your choice can be colour coded and easily selected by pressing the corresponding coloured button on the remote control handset. 1. Press a 2. Using the NUMBER 3. 4. coloured button. buttons, select the page you wish MODE to M programme. Press the OK button. Then the selected page is stored as the selected page number by blinking once. From now on, you can select this page with the same coloured button. The three other coloured buttons are programmed in this way. 25 Teletext TOP text The user guide displays the bottom of the four fields-red, green, yellow and blue field denotes the next group and the blue field indicates the next block. screen. The at yellow Block / group / page selection 1. With the blue button you can progress from block to block. 2. Use the yellow button to proceed to the next group with automatic overflow to the next block. 3. With the green button you can proceed to the next existing page with automatic overflow to the next group. Alternatively the D button can be used. 4. The red button permits to return to previous selection. Alternatively the E button can be used. Direct page selection Corresponding to the SIMPLE teletext mode, you can select a page by entering it as a three digit number using the NUMBER buttons in TOP mode. PR OK FASTEXT PR The teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button. 123 selection i button to select the index page. Press the You can select the pages which are colour coded along the bottom line with the same coloured buttons. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three digit page number with the NUMBER buttons in FASTEXT mode. The D / E button can be used to select the preceding or Page 456 1. 2. 789 3. 0 4. following INDEX i 26 M page. Teletext Special ? ENGLISH teletext functions REVEAL Press this button to display concealed information, such as solutions of riddles or puzzles. Press this button again to remove the information from the display. SIZE Selects double Press Press height text. this button to enlarge the top this button again to enlarge page. Press this button again half of the page. the bottom half of the to return to the normal display. PR UPDATE Displays the TV picture on The display the screen while waiting for the new teletext page. will appear at the top left hand corner of the screen. When the updated page is available then will change to the page number. display Press this button to view the updated teletext page. PR 123 HOLD the automatic page teletext page consists of 2 Stops which will change occur if a 456 sub pages. The number of sub pages and the sub page displayed is, usually, shown on the screen below the time. When this button is pressed or more the stop symbol is displayed the screen at the top left-hand corner 789 of 0 and the automatic page change is inhibited. To continue press this button again. MIX the teletext pages superimposed on the TV To switch the TV picture off press this button again. Displays picture. TIME UPDATE TIME SIZE MIX HOLD REVEAL ? When viewing TV programme, press this button to display the time at the top right hand corner of the screen. Press this button again a to remove the display. In the teletext mode, press this button to select a sub page number. The sub page number is displayed at the bottom of the screen. To hold or the sub page, press the NUMBER buttons. change Press again RED/GREEN, D / E or to exit this function. 27 Connection of external You equipment connect additional equipment, such etc. to your set. Examples are shown below. can as VCRs, camcorders Aerial socket 1. VCR 2. 3. 4. 5. 12 Euro scart socket 1. VCR Connect the RF out socket of the VCR to the aerial socket of the set. Connect the aerial cable to the RF aerial in socket of the VCR. Store the VCR channel on a desired programme number using the 'Manual programme tuning' section. Select the programme number where the VCR channel is stored. Press the PLAY button on the VCR. 2. (VCR) Connect the Euro scart socket of the VCR to the Euro scart socket of the set. Press the PLAY button on the VCR. If your VCR outputs an AV switching signal via the Scart lead the set will auto switch to AV 1, AV 2 mode on start of playback, but if you want to keep on watching in TV mode, press the D / E or NUMBER buttons. Otherwise press the TV/AV button on the remote control handset to select AV1. The VCR play back picture appears the screen. You can also record programmes received by the TV on on video tape. S-VIDEO VCR Note a. b. c. d. : i.e. the signals red, green and blue can only be selected for the Euro scart 1 and the AV 1 can be received. These signals are transmitted, for example, by a pay TV decoder, game machine or photo CD unit, etc. If both Euro scart 1, and 2 sockets have been connected to the VCRs simultaneously, only the AV 2 can be received. If the S-VHS signal is received through the S-VIDEO, you must change to the S-Video mode. Please use shielded scart cable. Signal type RGB, S-Video/Audio in sockets S-VIDEO VCR When connecting picture quality will 28 (S-Video) S-VIDEO VCR to the S-VIDEO be further improved. an socket, the 1. Connect the S-Video socket of the VCR to the S-VIDEO socket of the set. 2. Connect the audio cable from the S-VIDEO VCR to the AUDIO sockets of the set. 3. Select S-Video 4. Press the PLAY button on The VCR playback picture the TV/AV button repeatedly. the VCR. appears on the screen. by pressing Connection of external Euro scart socket 1. 2. 3. ENGLISH equipment (DVD) Connect the Euro scart socket of the DVD to the Euro scart socket of the set. Press the TV/AV or MULTIMEDIA button to select AV1 or AV2. Press the PLAY button on the DVD. The DVD playback picture appears on the screen. DVD input sockets (RZ-23LZ55***/ RZ-26LZ55***/ RZ-32LZ55***) 1. Connect the DVD output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y orYPBPR)oftheDVDtotheDVDINPUTsockets(YPBPR)of the set. 2. Connect the audio cable from the DVD to DTV/DVD INPUT AUDIO sockets of the set. 3. Press the TV/AV or MULTIMEDIA button to select Press the PLAY button on the DVD. 4. The DVD playback picture Audio/Video in sockets 1. 2. 3. appears on the Component. screen. (RZ-23LZ25*** only) Connect the audio/video out sockets of the VCR to audio/video in sockets of the set. Press the TV/AV button to select AV3. Press the PLAY button on the VCR. The VCR playback picture appears on the screen. Note : If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO socket of the set. VCR 29 Connection of PC PC in socket Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the PC input socket of the set. Connect the audio cable from the PC to the PC SOUND sockets of the set. Press the TV/AV or MULTIMEDIA button to select PC. Switch on the PC, and the PC screen appears on the set. The set can be operated as the PC monitor. 1. 2. 3. 4. PERSONAL COMPUTER Displayable MODE Monitor Resolution Connect the signal cable (DVI-D cable, Not DVI to D-Sub cable) from the DVI output socket of the PC to the DVI input socket of the set when using a PC with DVI output. In some video cards, DVI-Analogue output may not be supported. Note : Specification Horizontal Vertical Frequency(kHz) Frequency(Hz) VGA 640x480 31.4 60 SVGA 800x600 37.8 60 XGA 1024x768 48.3 60 1280x768 47.6 60 1360x768 47.6 60 WXGA (Synchronization input form : separate) Note : If the set is cold, there may be a small "flicker" when the set is switched on. This is normal, there is a. nothing wrong with the set. b. If possible, use the VESA 1360x768@60Hz video mode to obtain the best image quality for your LCD monitor. If used under the other resolutions, some scaled or processed pictures may appear the screen. The set has been pre-adjusted to the mode VESA 1360x768@60Hz. Some dot defects may appear on the screen, like Red, Green or Blue spots. However, this will have no impact or effect on the monitor performance. Do not press the LCD screen with your finger for a long time as this may produce some temporary distortion effects on the screen. When the PC screen appears on the set, a message may appear on the screen, and the message will differ according to the Window system version. If a message appears click "Next" until the message finishes. If the message "out of range" appears on the screen, adjust the PC as in the 'Displayable Monitor Specification' section. on c. d. e. f. DPM (Display Power Management) mode When the PC is in the power saving mode, automatically the monitor goes into DPM mode to energy. Note : Use the supplied signal cable with the set. Otherwise, DPM mode may not work. 30 save the Connection of PC PC ENGLISH PC Setup (only DVI-Analogue mode) H-Position V-Position You adjust horizontal/vertical position, clock, phase, configure, reset as you prefer. can and auto- Clock Phase Auto Configure Reset 1. Press the MENU button and then D / E button to select the Setup 2. 3. 4. DEFG menu. OK MENU Press the G button and then D / E button to select Input. Press the G button and then D / E button to select PC. Press the MENU button and then D / E button to select the PC menu. PC 87 H-Position V-Position Clock Phase Auto TV/AV Configure Reset MENU DEFG 5. 6. OK MENU Press the G button and then D / E button to select the desired picture item. Press the F / G button to make appropriate adjustments. H-Position / V-Position This function is to adjust PR OK VOL picture to left/right and up/down as you prefer. VOL PR Clock This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. Phase This function allows you to remove any horizontal noise and clear or sharpen the image of characters. Auto-configure This function is for the automatic adjustment of the screen position, clock and phase. The displayed image will disappear for a few seconds while the Auto-configuration is in progress. Reset This function allows you to return to the good picture reproduction programmed at the factory and cannot be changed. ? Note : Some signal from some graphics boards may not function properly. If the results are unsatisfactory, adjust your monitor's position, clock and phase manually. 7. 8. Press the OK button to store it for the PC monitor Press the TV/AV button to return to PC mode. picture. 31 External Control Device - Connect the RS-232C input jack to and control the Monitor's functions - - Connect the serial external control device are (such Setup as a computer or an A/V control system) externally. port of the control device RS-232C connection cables RS-232C an ; RS-232C not to the RS-232C supplied jack on the Monitor back panel. with the Monitor. Setup PC Type Type of of Connector; D-Sub 9-Pin 9-Pin Male 1 No. Pin 1 No connection 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS name 5 (Receive data) (Transmit data) (DTE side ready) (DCE side ready) (Ready to send) (Clear to send) 9 6 No Connection 9 RS-232C Configurations 3-Wire Configurations (Not standard) 7-Wire Configurations (Standard RS-232C cable) PC TV PC TV RXD 2 3 TXD RXD 2 3 TXD TXD 3 2 RXD TXD 3 2 RXD GND 5 5 GND GND 5 5 GND DTR 4 6 DSR DTR 4 4 DTR DSR 6 4 DTR DSR 6 6 DSR RTS 7 8 CTS RTS 7 7 RTS CTS 8 7 RTS CTS 8 8 CTS D-Sub 9 32 D-Sub 9 D-Sub 9 D-Sub 9 External Control Device Setup ; RS-232C ENGLISH Set Set ID Use this function to - Refer to 'Real Data - specify a monitor ID number. Mapping 1'. See page 34. 1. Press the MENU button and then Setup button to select the use D / E Setup menu. Language 2. Press the G button and then use D / E 3. Press the G button and then use Input button to select Set ID. F / G button to choose the desired monitor ID number. The adjust adjustment Child lock Set ID Set ID to 1 range of SetIDis1~99. 4. Press the OK button to save. DEFG OK MENU Communication Communication Parameters ? Baud rate ? Data ? * : 9600 length Parity : None Use : a bps (UART) ?Stopbit:1bit 8 bits crossed ? (reverse) Communication code cable. Command Command Reference List COMMAND COMMAND 2 1 01. Power ASCII code : k a ransmission / T Transmission DATA (Hexa) Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] 0~1 * [Command 1]: First command. (j or k) [Command 2]: Second command. [Set ID]: You can adjust the set ID to choose desired monitor ID number in Special menu. Adjustment range is 1 99. When selecting Set ID '0', every connected Input Select Aspect Ratio k k c 04. Screen Mute k d 0~1 05. Volume Mute k e 0~1 06. Volume Control k f 0~64 TV set is controlled. Set ID is indicated 07. Contrast k g 0~64 08. k h 0~64 (1~99)on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol. 02. 03. b Receiving * * Brightness 0~6 * ~ * 09. Color k i 0~64 [DATA]: Transmit 'FF' data to read status of command. kj0~64 11. k k 0~64 k l 0~1 k m 0~1 14. Balance k t 0~64 15. Tune Command m a 0~63 OK Acknowledgement 16. Add/Delete mb 0~1 [Command2][ ][Set ID][ ][OK][Data][x] 17. m Key 12. OSD Select 13. * : Key Lock Key Refer to '02. Input Select' on c Code decimal To transmit command data. 10. Tint Sharpness as * [Cr]: Carriage Return ASCII code '0x0D' * * page 34 [ ]: ASCII code 'space (0x20)' The Monitor transmits ACK (acknowledgement) this format when normal data. At this receiving based on time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The Monitor transmits ACK (acknowledgement) this format when abnormal data from non-viable functions or receiving communication based on errors. 33 External Control Device 01. Power On You also can mute on/off. adjust mute Power Off 1 :PowerOn Data 0 : Volume mute off 1 : Volume mute (Volume on) (Volume off) on G To show Power On/Off. Acknowledgement Transmission [e][ ][Set ID][ ][OK][Data][x] [k][a][ ][Set ID][ ][FF][Cr] 06. Volume Control Acknowledgement Power Off (Command:f) G To adjust volume. [a][ ][Set ID][ ][OK][Data][x] : on [k][e][ ][Set ID][ ][Data][Cr] [a][ ][Set ID][ ][OK][Data][x] 0 the MUTE button Transmission Acknowledgement Data using remote control. [k][a][ ][Set ID][ ][Data][Cr] : (Command:e) G To control volume Transmission 0 Setup 05. Volume Mute (Command:a) G To control Power On/Off of the TV. Data ; RS-232C You 1 adjust volume with the volume buttons remote control. on :PowerOn also can Transmission 02. Select Input G To select input You source also select can button (Command:b) (Main an Picture Input) for the TV. input Data using source the TV/VIDEO Min:0~Max:64 ? Refer to 'Real data mapping the TV's remote control. on 10 :TV 30 : 20 :AV1 40 : 21 :AV2 60 :PC S-Video Component or AV3 07. Contrast G To adjust You screen also can contrast. adjust contrast in the Picture Transmission [b][ ][Set ID][ ][OK][Data][x] [k][g][ ][Set ID][ ][Data][Cr] Data Ratio G To adjust the You (Command:c) (Main picture format) screen adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen ? Refer to 'Real data 0 : Normal 1 : Wide In PC mode You 3:Zoom (4:3) (16:9) screen screen only 16:9 and 4:3 as shown below. : 6 : Spectacle Original are available. also can brightness. adjust brightness screen 04. Screen Mute (Command:d) G To select mute on/off. Data Min:0~Max:64 ? Refer to 'Real data mapping [h][ ][Set ID][ ][OK][Data][x] * Real data 0 mapping :Step0 A:Step10 [k][d][ ][Set ID][ ][Data][Cr] : Screen mute off 1 : Screen mute on (Picture on) (Picture off) Acknowledgement [d][ ][Set ID][ ][OK][Data][x] menu. [k][h][ ][Set ID][ ][Data][Cr] Transmission 0 in the Picture Transmission Acknowledgement [c][ ][Set ID][ ][OK][Data][x] screen 4 aspect ratios Acknowledgement 34 1' Brightness (Command:h) G To adjust 2:14:9 Data mapping [g][ ][Set ID][ ][OK][Data][x] 08. [k][c][ ][Set ID][ ][Data][Cr] * Min:0~Max:64 menu. Transmission Data menu. Acknowledgement format. also can shown below. (Command:g) Acknowledgement Aspect as [f][ ][Set ID][ ][OK][Data][x] [k][b][ ][Set ID][ ][Data][Cr] 03. 1' Acknowledgement Transmission Data [k][f][ ][Set ID][ ][Data][Cr] F:Step15 10:Step16 64 : Step 100 *Tint:-50~+50 1 1' as shown below. External Control Device 09. Color (Command:i) G To adjust the You can also 15. Tune Command color. screen G Tune channel color in the Picture adjust Setup ; RS-232C to menu. (Command:m a) Transmission [k][i][ ][Set ID][ ][Data][Cr] [m][a][ ][Set ID][ ][Data0][ ][Cr] Data Data0: ? Refer to 'Real data Min 1'. See page 34. mapping Programme Number Max : 63(transmit by 0 : number. following Physical/major/minor Transmission Min:0~Max:64 ENGLISH ~ Hexadecimal code) Acknowledgement [i][ ][Set ID][ ][OK][Data][x] Acknowledgement 10. Tint [a][ ][Set ID][ ][OK][Data0][x] [a][ ][Set ID][ ][NG][Data0][x] (Command:j) G To adjust the You can tint.(NTSC screen also adjust M input only) tint in the Picture menu. Transmission 16. [k][j][ ][Set ID][ ][Data][Cr] G To skip the Data Transmission :Green0~Red :64 ? Refer to 'Real data mapping 1'. See page 34. Skip programme (Command:m b) current programme. [m][b][ ][Set ID][ ][Data 0][Cr] Acknowledgement Data0: [j][ ][Set ID][ ][OK][Data][x] (Programme)Skip on-0, (Programme)Skip off-1 Acknowledgement 11. Sharpness (Command:k) G To adjust the You can sharpness. adjust sharpness in [b][ ][Set ID][ ][OK][Data0][x] [b][ ][Set ID][ ][NG][Data0][x] screen also the Picture menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] 17. Data G To send IR Min: 0 ? ~ Max: 64 Refer to 'Real data mapping 1'. See page 34. Key (Command:m c) key code. Transmission Acknowledgement [m][c][ ][Set ID][ ][Data][Cr] [k][ ][Set ID][ ][OK][Data][x] Data: 12. OSD Select remote (Command:l) G To select OSD (On Screen Display) Key code Acknowledgement mute on/off. [c][ ][Set ID][ ][OK][Data][x] Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 0: OSD mute 1: OSD mute off on code code Acknowledgement Key [l][ ][Set ID][ ][OK][Data][x] Function Code Function Code MUTE 09 SSM 52 POWER 08 PSM 4D LIST 53 SLEEP 0E Q.VIEW 1A ARC 79 MENU 43 TEXT 20 PR+ 00 UPDATE 62 PR- 01 SIZE 64 Acknowledgement VOL+ 02 HOLD 65 [m][ ][Set ID][ ][OK][Data][x] VOL- 03 INDEX 70 OK 44 TIME 26 11 MIX 24 12 REVEAL 2A 13 MODE 22 14 BLUE 61 15 YELLOW 63 16 GREEN 71 17 RED 72 18 TV/AV 0B 19 TV/PC 98 10 I/II 0A 13. Key Lock G To lock the (Command:m) remote control and the front panel controls on the TV. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data ? If 0: Lock off 1: Lock on the remote control and front panel controls on the TV, use this mode. When main power is on/off, remote control lock is released. you're not 14. Balance using (Command:t) G To adjust balance. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 (transmit by Acknowledgement [t][ ][Set ID][ ][OK][Data][x] Hexadecimal code) 1234567890 35 Checklist Troubleshooting The doesn't work Power is suddenly normally. ? if there is any control causing obstruction. ? Are batteries installed with correct ? Correct remote ? Install new ? Is the sleep ? Check the power control settings. Power interrupted No broadcast on station tuned with Auto off activated. The remote control turned off ? Check to does not work operation see operating object between the polarity (+ mode set: product to +, - to and the remote -)? TV, VCR etc.? batteries. timer set? The video function does not work. No picture & No sound Check whether the ? Try ? Is the power cord inserted into wall power outlet? Check your antenna direction and/or location. ? Picture appears slowly after switching ? Test the wall power outlet, plug another product's power cord into the outlet where the product's power cord was plugged in. ? This is on or poor color poor picture normal, the image is muted during the product startup process. Please contact your service center, if the minutes. ? or with the broadcast. ? ? No another product is turned on. channel. The problem may be ? ? ? has not picture appeared after five Adjust Color in menu option. Keep a sufficient distance between the product and the VCR. Try another channel. The problem may be with the broadcast. Are the video cables installed properly? Activate any function to restore the brightness of the picture. Horizontal/vertical bars ture Poor Lines 36 on channels or Check for local interference such ? Station or ? Station signal ? Check for ? Check antenna or reception some in picshaking ? streaks pictures cable is as an electrical product experiencing problems, weak, reorient sources of possible (Change appliance or power tool. tune to another station. antenna to receive weaker station. interference. the direction of the antenna). Troubleshooting Checklist ENGLISH The audio function does not work. No ? Press the VOL Picture OK & ? Sound muted? Press MUTE button. No sound ? Try ? Are the audio cables ? Adjust ? A output from of the one another channel. The Balance in problem may be installed properly? menu with the broadcast. option. speakers Unusual sound from inside the change in ambient noise when the product the humidity or temperature may result in an unusual product is turned on or off and does not indicate a fault with product. There is a (Only The button. (or Volume) signal range. Vertical bar PC mode horizontal ? Adjust resolution, ? Check it whether the ? Check the ? Work the Auto ? Check the ? Reinstall the PC video card. is out of input in PC mode. problem applied) frequency, or vertical cable is connected signal frequency. or loose. source. or stripe on background & configure or adjust clock, phase, or H/V position. Horizontal Noise & Incorrect position Screen color is unstable or single signal cable. color 37 How to the join product assembly the set protect tumbling to Please set it up carefully Set it up close to the wall so the The instructions shown below is when it is the to the wall product so the doesn't fall product over when it is doesn't fall pushed over. backwards. safer way to set up the product, which is to fix it on the wall so the product doesn't fall over in the forward direction. It will prevent the product from falling forward and hurting people. It will also prevent pulled product from damage a caused by fall. Please make sure that children don't climb on or from the hang product. Accessories / Under 23 inches model 2-TV Bracket Bolts 1-TV Bracket, 2-Wall Bracket The Product Back Side 1-TV Bracket 2-Wall Brackets The Product Back Side 3 1 2 Under 23 inches model Under 23 inches model 1. Use the bracket and the bolt to fix the 2. 3. product to the wall as shown in the picture. Secure the bracket with the bolt (not provided as parts of the product, must purchase separately) on Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. so it becomes horizontal between the wall and the product. the wall. It is safer to tie the rope Notes ? ? ? When moving the product to another place undo the ropes first. Use a product holder or a cabinet that is big and strong enough for the size and weight of the product. To use the product safely make sure that the height of the bracket that is mounted on the wall is same 38 as that of the product. MEMO ENGLISH 39
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project