LG | F1403YD6 | LG F1403YD6 Owner’s Manual

Safety instructions for use
Cleaning and Maintenance
Electrical connection
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric
Cleaning the water inlet filter
Turn off the
water tap
Unscrew the
water inlet hose
Pull out the water Clean the filter using Tighten up the
inlet filter
a hard bristle brush inlet hose
To minimize the risk of fire within the inner bowl, the following should be observed:
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person to
prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may
burst under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
Cleaning the drain pump filter
The hose supplied with the machine must be used.
Old hoses may not be reused.
Open the lower
Unplug the drain
filter cover and pull hose plug Then
out the drain hose. open the filter by
turning to the left
Close the lower
After cleaning, refit the
drain filter cap and tighten it cover
by turning it clockwise. and
insert the drain plug
Remove any
matter from the
pump filter
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young Children should be supervised to ensure that they do not play with appliance.
Installation of drain hose
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be
placed in a tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat sources Such as in a tumble dryer.
The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot
escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent
heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce,
but not eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature
of the items. They should not be removed from the tumble dryer or piled or stacked while hot.
• Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, dry-cleaning
solvents or other flammable or explosive substances should not be placed in a tumble dryer.
Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol,
petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and wax removers.
• Items containing foam rubber (also known as latex foam) or similarly testured rubber like materials should not be
dried in a tumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
• Fabric softeners or similar products should not be used during a drying cycle, to eliminate the effects of static
electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or product.
• Undergarments that contain metal reinforcements should not be placed in a tumble dryer.
Damage to the tumble dryer can result if metal reinforcements come loose during drying.
When available a drying rack could be used for such items.
• Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer.
• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, rubber boots and rubber-coated tennis
shoes should not be placed in a tumble dryer.
Cleaning the dispenser drawer
Insert the
dispenser drawer
Cleaning in general
Important: Do not use methylated spirits, solvents or similar products.
Proper care of your washing machine can extend its service life.
The outside of the machine can be cleaned with warm water and
a neutral non-abrasive household detergent. Immediately wipe off
any spillage. Wipe with damp cloth. Avoid striking the surface with
sharp objects. Never hose down the machine!
Dry around the washing machine door
opening, flexible gasket and door
glass. Run washing machine through a
complete cycle using hot water. Repeat
process if necessary.
ca. 105 cm
ca. 145 cm
ca. 105 cm
max. 100 cm
Clean inside the
recess with an
old toothbrush
ca. 145 cm
min. 60 cm
Clean the dispenser
drawer under
flowing water
ca. 100 cm
60 – 100 cm
Pull out the
dispenser drawer
max. 100 cm
BS Plug Safety Details (For U.K. User)
ca. 100 cm
min. 60 cm
5 Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry or
max. 100 cm
min. 60 cm
• The drain hose should not be placed higher than 100 cm above the floor.
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
• If the drain hose is too long do not force back into the washing machine. This will cause abnormal
noise and cause the machine to malfunction and leak.
Green and
Yellow (Earth)
This appliance must be earthed As the colours of the wires in the mains
lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows: The green and
yellow wire must be connected to the terminal in the plug marked E or by
the earth symbol
or coloured green or green and yellow.
The wire coloured blue must be connected to the terminal marked with the letter N or coloured black.
The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. If a 13
amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
Safety instuctions for the installation
Safety instructions for use
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating
instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these
operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold
drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper
and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect
by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been
used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain
in the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflammable gas.
Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
• When this crossed-out wheeled bin symbol is attached to a product it means the product is covered
by European Directive 2002/96/EC.
• All electrical and electronic products should be disposed of separately from municipal waste stream
via designated collection facilities appointed by the government or the local authorities.
• The correct disposal of your old appliance will help prevent potential adverse consequences for the
environment and human health.
• For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
Install or store the appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit the power plug
to a grounded wall socket that complies with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the appliance
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
• Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
• If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
• The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed , that a Service Technician can gain easy access in the event of a
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
• Water supply is not adequate in area
• Water supply taps are not completely
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are
Check another tap in the house.
Fully open tap.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information, please
refer to “Cleaning the drain pump filter”
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both
robe, etc.), this system may stop spinning
or even interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of
the cycle, add smaller articles of laundry
to balance the load and repeat the spin
cycle. Floor is unstable.
Feet are not adjusted
CAUTION about the power cord
We recommend connecting most appliances to a dedicated circuit which is protected by a mains fuse. That is, a single outlet
supplying power only to the appliance concerned, without any additional outlets or branch circuits. Check the specifications
of this owner‘s manual. Do not overload wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension
cords, frayed power cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric
shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect
the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or
walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
• Is the door opened or not
completely closed?
• Water overfills due to the faulty water
CAUTION about the floor surface
• The installation surface must be clean, dry and level.
• Install washing machine on a flat hard floor. Poorly constructed timber base floors can contribute to excessive noise and
• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
• The washing machine must be perfectly level and firmly in position.
• It must not “see-saw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
• The washer experienced a power
Technical Specification
Name of product
Front loading washing machine
Max. Watt
2100 W (Wash) / 1500 W (Dry)
Power supply
220-240 V~, 50 Hz
8 kg (Wash) / 4 kg (Dry)
Size WxDxH mm:
600 x 640 x 850
Water consumption
72 kg
Permissible water pressure 1.0-10 bar (100-1000kPa)
Add 1 or 2 similar items to help balance
the load.
Rearrange load to allow proper spinning
Ownerʻs Manual
The floor should be a solid surface.
Adjust the feet so that the machine
does not rock from side to side or front
to back.
Close the door completely.
If the "
" does not clear, call for
Unplug the power plug and call for
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the
stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain
(gully) in the immediate vicinity. If relocating the appliance use the original packing material. Packaging material (e.g. plastic film,
Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children and do not
allow children to play inside the bowl as they may become trapped.
Straighten hose(s).
Check the filter of the inlet hose(s).
• Water level sensor has malfunctioned.
Close the water tap.
Unplug the power plug.
Call for service.
• Over load in motor.
• Check water supply.
Rattling and clanking noise
Thumping sound
Vibrating noise
Water leaks.
Excessive suds
Washing machine does not start
Washing machine won’t spin
Door does not open
Restart the cycle.
Turn the tap on.
If “
” is not released, unplug
power plug and call for service.
Extraneous objects such as coins or safety pins maybe in drum or pump.
Heavy wash loads may produce a thumping sound. This is usually normal.
Have all transit bolts and packing been removed?
Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary.
Too much detergent or unsuitable detergent.
Power cord may not be plugged in or connection may be loose.
Check that the door is shut.
Check that foreign objects may be blocking the drain causing the water not to drain out.
Once started, the door can not be opened for safety reasons.
At the end of the cycle or when Start Pause is pressed, wait one or two minutes before opening the door to
allow the electric locking mechanism time to release.
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your
washing machine.
For the U.K. customer
CUSTOMER SERVICES Tel. : +44-(0) 844 847 LGLG(5454) Fax. : +44-(0) 844 847 1413
LGEUK SERVICE WEB-SITE : http://www.lge.co.uk
P/No.: MFL62883821
Washing temperature
Luke warm ironing
- empty all pockets
- remove all metal parts
- place the delicate textiles into the laundry net
- close zippers
- wash new textiles separately
- do not prewash
- pretreat dirty spots
- pre wash
Drying cycle
Additional programs
Do not iron
Do not bleach
Hang to dry
Handy to bleach
Drip dry
Pre Wash
The Pre wash compartment can be used
for Normal to heavy soiled clothes, by adding a prewash or normal detergent to this
compartment before selecting this wash
option with the Cycle.
Main Wash
For Laundry requiring detergent, place
recommended dosage in to this compartment. Please note that liquid detergent
will enter the tub as it is poured and may
not be suitable for a delay start.
Do not exceed the MAX-Level.
Highly densed softeners are to be
diluted with some water.
Excessive softener can cause brown
or grey spotting on the clothes.
How to set “Time Delay”
Loading the Drum
Check the folds of the flexible gasket (grey) and remove any small articles or foreign objects that may have
fallen from items in the previous wash . 2
Check all garments for loose items before loading and ensure that
clothes are clear of the door gasket before closing the door so that
the clothes or door gasket are not damaged during the wash.
Baby Care
Quick 30
Hand Wash
/ Wool
Control panel
Power button
Program Cycle
Start / Pause
Dry (Option)
Fill detergent
Refer to the
written information
on the detergent's packaging
Maximum Load
Turn off tap
- Close water supply
- Clean the machine
- Unplug machine
Washing program table
Water Temp.
Fabric Type
Color fast garments (shirts,
nightdresses, pajamas...)and lightly (Cold, 30°C, - Time Delay
soiled white cotton (underwear)
40°C, 95°C) - Intensive
Lightly soiled clothing and
- Medic Rinse
small loads
(Cold, 30°C, - Pre Wash
- Rinse+
Polyamide, Acrylic, Polyester
- Rinse+Spin
- Normal+Hold
Lightly soiled baby wear
(40°C, 95°C)
- Time Delay
- Intensive
A small amount of laundry
- Medic Rinse
which can be dried.
40°C, 95°C) - Pre Wash
- Rinse+
Colored laundry which is
lightly soiled fast
(Cold, 40°C) - Time Delay
Delicate laundry easily
- Intensive
- Rinse+
“Hand wash” marked delicate
- Rinse+Spin
and wool laundry
- Normal+Hold
Cotton bedding with filling
(Cold, 30°C)
duvet, pillow, blanket, sofa
cover with light filling
- Press Power button.
- Turn the Program dial to select the program you require.
- Press Time Delay button and set the finishing time. The machine will then automatically work
out the turn on time based on the chosen cycle.
- Press the Start/Pause button.
- Low Temp.
- Iron Dry
- Cupboard Dry
- Eco Dry
- Time
If the laundry is heavily soiled “Intensive”option is effective.
Turn the machine ON
by pressing the Power button
Less than 4.5 kg
Filter cover.
Additional Steps
- Turn the machine off
- Leave door open to
allow drum to dry
Less than 4 kg
Select an Option
Pre Wash / Rinse+Spin / Rinse + / Normal+Hold
• Recommend Automatic drying course as a kind of clothes.
a) Low Temp. : For Synthetics select
d) Eco Dry : A special cycle to reduce water usage during
b) Iron Dry : If you want to iron clothes
the dry cycle.
c) Cupboard Dry : For Cottons select
e) Time (30/60/120 minutes) - 30 min. : Cotton 1.5 kg
- 60 min. : Cotton 3 kg
- 120 min. : Towel 4 kg
Note: The estimated drying time varies from the actual drying time with an Automatic.
The type of fabric, size of the load, and the dryness selected affect drying time.
2.Drying time guide
• Drying course can last up to 150min.
When selecting drying only, drying course will start after spining.
• These drying times are given as a guide to help you set your dryer for manual drying.
Drying times can vary greatly depending on dampness, room temperature and type of fabric
and your own experience will be your best guide.
Woolen Articles
Medic Rinse
Cold water tap must be left on during drying cycles.
Select Spinning speed
and Washing temperature
Press Start / Pause
to start or pause the washing
Select the
Dry mode
f in
4 additional programs
Time Delay / Favorite / Intensive / Medic Rinse
• This washer-dryer’s automatical process from washing to drying can be selected easily.
• For most even drying, make sure all articles in the clothes load are similar in material and thickness.
• Do not overload dryer by stuffing too many articles into drum. Items must be able to tumble freely
• If you open door and remove load before dryer has finished its cycle, remember to press the
Start/Pause button.
• By turning the DRY dial, you can select :
Cupboard Dry Eco Dry 30 60 120 Low Temp. Iron Dry
• After the end of dry, “
” is displayed. By pressing the “Start/Pause” button the
program can be ended. If you not press the “Start/Pause” button, the program is ended after
about 4 hours. “
” Cooling Cycle.
 3 sec.
 3 sec.
Woven and Loopknit Materials
Permanent Press and Synthetics
- Do not overload your dryer
- Take out permanent press articles as soon as the
dryer stops to reduce wrinkles.
Baby clothes and Night Gowns
- Always check the manufacture’s instructions.
Fiber glass
- Do not dry fiberglass articles in your dryer. Glass particles
left in the dryer could be picked up by your clothes the next
time you use the dryer and irri tate your skin.
Fiber or Leather Materials
- Always check the manufacture’s instructions.
3.Completion of Drying
• When drying cycle is completed, “
” [Cool Down] is displayed on the Multi display.
• The Cool Down is setting automatically when a drying cycle is complete.
• When you are not remove a loaf of clothes from the dryer as soon as it stops, wrinkles can form.
• The Cool Down operating periodically tumbles, rearranges and fluffs the load to tumbles, rearranges and fluffs the
load to hours.
• The “
” message will continue to display until the clothes are removed or the Start/Pause button is pressed.
 3 sec.
Press and hold
To deactivate:
the Option buttons Start/
press and hold
the Option buttons simultaneously
simultaneously for 3
seconds until the
" " is removed
from the display.
Select the desired
TUB CLEAN is special cycle to clean the inside of the washing machine.
A higher water level is used in this cyle at higher spin speed. Perform this cycle regularly.
 3 sec.
Empty the drum
completly and close
the door
Rubber and Plastics
- Do not dry any items mode from or containing rubber
or plastics, such as:
a) aprons, bibs, chair covers
b) curtains and table cloths
c) bathmats
Change to the desired program, whilst in child lock mode:
To activate:
press and hold
the Option buttons
simultaneously until
" " appears in the
Tub Clean
• By turning the DRY dial, the drying time can be selected.
- Some woven and loopknit materials may shrinks, by varying
amounts, depending on their quality.
- Always stretch them out immediately after drying.
Available in the Cotton, Cotton Quick, Synthetic, Baby Care and Wash+Dry (4kg/4kg) programs.
Medic Rinse is set by default in the Baby Care program.
The respective temperature indicator will light up.
Select this function to lock the buttons on the control panel and to prevent tampering.
Note: The last 6 minutes of dryinng time, A sensor(Thermistor) detects clothes drying conditions.
When the dryness is low, cycle time will be added by max. 30 mins with “6” mins remaining window display.
- Do not tumble dry woolen articles. Pull them to their
original shape and dry them flat.
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the
products are washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0806.
Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.
Warning: Keep all washing powder and detergents away from children. Danger of poisoning
Remove laundry
- Open the door
- Remove the laundry
Child Lock
• Use your Automatic Cycles to dry most loads. Electronic sensors measures the temperature of the exhaust
to increase
or decrease drying temperatures for faster reaction time and tighter temperature control.
This allows the final rinse to be heated to 40 degrees.
Less than 2 kg
Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufacture’s care label or instructions when washing.
Intensive: If the laundry is heavily soiled “Intensive” option is effective.
Set program at “Wash : Cotton 60°C + Intensive” and “Dry : Eco Dry (First drying cycle load : 4kg, Second drying cycle load : 4kg)” for test in accordance
with EN50229 and IEC50229.
Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cotton is recommended.
Pre Wash is available in the Cotton, Cotton Quick, Synthetic, Baby Care and Wash+Dry (4kg/4kg) programs.
Rinse + : Used to introduce an additional rinse, which may assist in removing traces of detergent residue.
Medic Rinse: For best results or for cleaner rinsing, you can choose this heated Rinse option. Medic Rinse is automatically selected on Baby Care program.
1. Drying Automatic guide
- By selecting the Intensive option, the washing duration may be extended, depending on
the program selected.
- To use this option, press the intensive button once before the wash program is started.
For best results or for cleaner rinsing, select the “Medic Rinse” option.
Select a
1 king size
(9 Tog)
- Favorite program allows you to store a customized wash cycle for future use.
- To make a Favorite program:
(1) Select a cycle.
(2) Select
The course, washing method, number of rinses, spin speed, water temperature etc.
(3) Press and hold Favorite program button 3 econds (2 beep sounds).
The Favorite program is now stored for future use.
To reuse the program, select Favorite program and press Start/Pause.
Less than 7 kg
- make use of the max. washing quantity
- do not “pre wash” if possible
- use short program if possible
Time Delay
- remove extraneous objects
- leave door open to dry the drum
- check the rubber seals regularly
Dry flat
- with hardness III water
- use water softening agent
Do not tumble dry
Dispenser drawer
Hot ironing
Do not wash
Turn on the water tap
Never touch the plug with wet hands!
Never remove the plug from the
socket by pulling on the cord.
Medium hot ironing
Additional programs
Allows you to set the cycle's ending time (by hourly increments) in advance.
Never use a defective machine! In case of any
failure, first unplug the machine and turn off the
water tap.
Hose elbow connection e.g. attach to water tap
Sort the laundry
note washing instruction symbols Degree of soiling Type of textile / colour -
Washing symbols
Add anti-limescale
(Calgon) to the main
wash compartment.
Close the disp. drawer
Power ON with
Then press and
hold Spin and
Temp. button
Press the
button to start Tub
Clean process
After the cycle is
complete, leave the
door open to dry
Beep on / off
The Beep on/off function can be set only during the washing cycle.
To set the Beep On/Off function follow the below steps.
1.Turn on the washing machine (by pressing the Power button).
2.Press the Start/Pause button.
3.Press and hold the Option and Spin button simultaneously for three seconds to set
Beep on/off function.
Once the Beep on/off function is set, the setting is memorized even after Power is off.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF