LG | F1247TD | LG F1247TD Owner’s Manual

Remove Packaging
• The appliance is fitted with transit bolts to prevent internal
damage during transport. Be careful, heavy load!
• Packing and all transit bolts must be removed before using
the washing machine.
• When unpacking the base, be sure to remove the additional
packing support in the middle of the base packing.
original packing for future move.
i Store
Dispose of packing material according to local regulations.
2
Schraubenschlüssel
1
3
To prevent internal damage during transport, the
special 4 bolts are locked.
If they are not removed, it
may cause heavy vibration, noise and machine to
malfunction.
2
Remove the 4 bolts
along with the rubber
bungs by slightly twisting the bung.
L
CAUTION about positioning the appliance
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
Fuse
This appliance must be earthed As the colours of the wires in the mains lead
of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows: The green and yellow wire must
be connected to the terminal in the plug marked E or by the earth symbol or
coloured green or green and yellow. The wire coloured blue must be connected to the terminal marked with the letter
N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured
red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
N
Cord
grip
• The drain hose should not be placed higher than 100 cm above the floor.
4
Unscrew the 4 bolts
3. Die 4 Schrauben
lösen und die
using the spanner
supplied. etwas drehen, um sie
Gummipfropfen
zusammen mit den Schrauben abzunehmen.
Die 4 Schrauben und den Schraubenschlüssel
für späteren Gebrauch aufbewahren.
Close the holes with
the caps supplied.
5
Connecting water supply hose
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
The hose supplied with the machine must be used. Old hoses may not be reused
• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.
Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)
7
Don’t strip or crossthread when connecting inlet hose to the valve.
• Die Transportsicherungsschrauben müssen vor
jedem Transport des Geräts wieder angebracht
werden.
Level adjustment
• Proper level-adjustment of the washing machine prevents excessive noise and vibration.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
If the water supply pressure is more than 1000kPa, a decompression
device should be installed.
Keep the 4 bolts and the spanner for the future use. Refit transit bolts before transporting the appliance.
3
Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
BS Plug Safety Details (For U.K. User)
E
Requirements for installation site
4. Die Schraubenbohrungen mit den
beiliegenden Kappen verschließen.
• If the floor is uneven, adjust feet as required.
(Do not insert pieces of wood etc. under the
feet). Make sure that all four feet are stable
Adjustable feet Adjustable feet
and resting on the floor. Then check that
the appliance is perfectly level. (Use a spirit
level).
• Two rubber seals are supplied with the water inlet
hoses. They are used for preventing water leaks.
• Make sure the connection to taps is tight enough.
Level floor: Permissible floor gradient under entire washing machine
is 1˚ .
• Periodically check the condition of the hose and
replace the hose if necessary.
5
• Make sure that there is no kink on the hose and that
it is not crushed.
Power socket: Must be within 100 cm of either side of location of
washing machine. Do not overload the socket with more than one
appliance.
Additional Clearance: For wall, floor and door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or store laundry products on top of the washing machine at any times. They can damage
the finish or controls of the machine.
i
If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional
type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting
the tap into the adaptor.
Safety instructions for use
Safety instuctions for the installation
Installation of drain hose
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person to prevent
danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced
persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst under
pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine standing
at room temperature for a few hours before putting it into operation.
Green and
Yellow (Earth)
Brown(Live)
Blue(Neutral)
Transit bolts
6
Electrical connection
4
60 - 100 cm
1
• Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
• If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
• The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
CAUTION about the power cord
We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the specifications of this owner‘s manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the
cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic film, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.
CAUTION about the floor surface
• The installation surface must be clean, dry and level.
• Install washing machine on a flat hard floor.
• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
• The washing machine must be perfectly level and firmly in position.
• It must not “see-saw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
@
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating
instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these
operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only
with cold drinking water and only for washing textiles with washing detergents designed for washing machines.
Every other use is improper and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never
disconnect by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or
parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized
customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive
substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire
or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover
has been used then make sure that the solvent has been carefully washed out before inserting the clothes into the
appliance. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly
inflammable gas. Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of
scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to
protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
G arantiebedingungen
Technical Specification
Disposal
• When this crossed-out wheeled bin symbol is attached to a product it means the product is covered
by European Directive 2002/96/EC.
1.•
Wenn
Symboland
eineselectronic
durchgestrichenen
Abfalleimers
All dieses
electrical
products
should be disposed of separately from municipal waste stream
auf einem Produkt angebracht ist, unterliegt dieses Produkt
designated
collection
facilities appointed by the government or the local authorities.
dervia
europäischen
Richtlinie
2002/96/EC.
2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom
•Hausmüll
The correct
disposal of your old appliance will help prevent potential adverse consequences for the
über dafür staatlich vorgesehenen Stellen entsorgt
werden.
environment and human health.
3. Mit der ordnungsgemäßen Entsorgung des alten Geräts
•vermeiden
For more
detailed information about disposal of your old appliance, please contact your city office,
Sie Umweltschäden und eine Gefährdung der
persönlichen
Gesundheit.
waste disposal
service or the shop where you purchased the product.
Entsorgung von Altgeräten
8
CAUTION
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young children should be supervised to ensure that they do not play with appliance.
Name of product
Front loading washing machine
Max. Watt
2100 W
Power supply
220-240 V~, 50 Hz
Wash capacity
8 kg
Size WxDxH mm:
600 mm x 590 mm x 850 mm
Water consumption
56 (7 / kg)
Weight
63 kg
Permissible water pressure 1.0-10 bar (100-1000kPa)
4. Weitere Informationen zur Entsorgung des alten Geräts
erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt
oder in dem Geschäft, wo Sie das Produkt erworben haben.
Troubleshooting
guide
TNroubleshooting
Symptom
Possible Cause
• Water supply is not adequate in
area supply is not adequate in
• Water
•area
Water supply taps are not
• Water
supply open.
taps are not
completely
completely
•Water
inletopen.
hose(s) are kinked.
• Water inlet hose(s) are kinked.
Thefilter
filterofofthetheinlet
inlet
hose(s)
••The
hose(s)
areare
clogged.
clogged.
Solution
Check another tap in the house.
<Fig 1>
• If water leakage occurred in the inlet hose,
“ ” is
willkinked
be changed
red color.
•indicator
Drain hose
or clogged.
The drain
is clogged.
••Drain
hose filter
is kinked
or clogged.
• The drain filter is clogged.
• Load is too small.
Check another tap in the house.
Fully open tap.
Fully open tap.
Straightenhose(s).
hose(s).
Straighten
Checkthe
another
tapthe
in inlet
the house.
Check
filter of
hose(s).
Owner‘s Manual
Clean and straighten the drain hose.
Cleanand
thestraighten
drain filter.
Clean
the drain hose.
Clean
the drain
filter. information,
For more
detailed
For more detailed information,
please refer to “Cleaning the drain pump
please refer to “Cleaning the drain pump filter”
filter”
Add 1 or 2 similar items to help
F1447TD(1~9)
F1247TD(1~9)
••Load
Add
1 or 2the
similar
balance
load.items to help
Loadisistoooutsmall.
of balance.
• Load is out of balance.
the load.
Rearrange
load to allow proper
•
The appliance has an unbalance detection balance
• The appliance has an unbalance detection
Rearrange
spinning load to allow proper
and correction system. If individual heavy
and correction system. If individual heavy
spinning
articles
are
loaded
(ex.
bath
mat,
both
robe,
articles are loaded (ex. bath mat, both robe,
etc.),this
thissystem
system
may
stop
spinning
or even
etc.),
may
stop
spinning
or even
interruptthethespin
spin
cycle
altogether.
interrupt
cycle
altogether.
thelaundry
laundryis isstillstill
at the
of
••IfIfthe
tootoo
wetwet
at the
endend
of the
the cycle,
add smaller
of laundry
to
cycle,
add smaller
articlesarticles
of laundry
to
balance
repeat
thethe
spinspin
cycle.
balancethetheload
loadandand
repeat
cycle.
thedoor
dooropened
opened
or not
•• Is
Is the
or not
completely
closed?
completely closed?
Closethe
thedoor
doorcompletely.
completely.
Close
is not
released,
for service.
❋ IfIf “ “ ”is” not
released,
callcall
for service.
Unplug
Unplugthe
thepower
powerplug
plugand
andcall
callfor
forservice.
service.
••Water
Wateroverfills
overfillsdue
duetotothe
thefaulty
faultywater
water valve.
valve.
••Water
Waterlevel
levelsensor
sensor has
has malfunctioned.
malfunctioned.
Closethe
thewater
watertap.
tap.
Close
Unplugthe
thepower
powerplug.
plug.
Unplug
Callforforservice.
service.
Call
••Over
Overload
loadininmotor.
motor.
••Water
leaks experienced a power failure.
The washer
Restart
the cycle.
Call
for service.
• The washer experienced a power failure.
Restart the cycle.
Rattling and clanking noise
Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound
Heavy wash loads may produce a thumping sound. This is usually normal.
29
Vibrating noise
Have all transit bolts and packing been removed?
Water leaks.
Check and tighten hose connections. Unclog drain pipe.
Contact plumber if necessary.
Excessive suds
Too much detergent or unsuitable detergent.
Washing machine does not start
Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin
Check that the door is firmly shut.
Door does not open
Once started, the door can not be opened for safety reasons.
Wait one or two minutes before opening the door to allow the electric
locking mechanism time to release.
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your
washing machine.
For the U.K. customer
CUSTOMER SERVICES Tel. : +44-(0) 844 847 LGLG(5454) Fax. : +44-(0) 844 847 1413
LGEUK SERVICE WEB-SITE : http://www.lge.co.uk
P/No. :MFL61988407
Preparation
Washing symbols
CHECKING THE MACHINE
Never use a defective machine! In case of any
failure, first unplug the machine and turn off the
water tap.
WATER CONNECTION
Turn on the water tap
INSERT PLUS INTO THE MAINS SOCKET
Never touch the plug with wet hands!
Never remove the plug from the socket by pulling on the cord.
DOING LAUNDRY AND USING MACHINE
WITH CARE
- empty all pockets
- remove all metal parts
- place the delicate textiles into the laundry net
- close zippers
LAUNDRY WITH DIFFERENT AMOUNTS OF
SOILING
- wash new textiles separately
lightly
- do not prewash
- pretreat dirty spots
heavily
- pre wash
Washing temperature
Medium hot ironing
Do not tumble dry
Dry flat
Do not wash
Hot ironing
Hang to dry
Do not bleach
Luke warm ironing
Pre Wash
For normal dirty clothes use a small
amount of detergent. Don't pre wash.
Mount the level plate to use fluid detergents.
Program
Cotton
Cotton Quick
Handy to bleach
Main Wash
For very dirty clothes fill 1/4 of the
portion of detergent in here and
select a prewashing programm
C
Softener
Do not exceed the MAX-Level.
Highly densed softeners are to be
diluted with some water.
Fabric Type
Color fast garments (shirts, nightdresses,
pajamas...)and lightly soiled white cotton
(underwear)
Lightly soiled clothing and small loads
Polyamide, Acrylic, Polyester
Half load +
Cotton and cotton mix fabrics
* Economic course in small load also.
Especially optimized in half load.
Duvet
Hand Wash
/Wool
Quick 30
Cotton, bedding with filling duvet, pillow,
blanket, sofa cover with light filling
“Hand wash“ marked delicate and wool
laundry
Delicate laundry easily damaged
Colored laundry which is lightly soiled fast
Cotton and mix fabrics
* Special PROGRAM within 60min
for normally soiled laundry.
Water Temp.
(Selection)
60°C
(Cold, 30°C,
40°C, 95°C)
40°C
(Cold, 30°C, 60°C)
60°C
(Cold, 30°C, 40°C)
40°C
(Cold, 30°C)
30°C
(Cold, 40°C)
Option
(Selection)
Fill the drum
Check the folds of the flexible gasket (grey) and remove any small articles, if any. .
Check inside of the drum and remove - 2
any left in items for next wash cycle. .
Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages .
- Time Delay
- Soak
- Crease Care
- Medic Rinse
- Intensive
- Pre Wash
- Rinse+Spin
Maximum Load
Fill detergent
Refer to the
written information
on the detergent's packing
Control panel
Dispenser
drawer
- Time Delay
Program Cycle
Start button
Temp.
Rinse
Spin
Drum
Turn off tap
- Close water supply
- Clean the machine
- Unplug machine
A
Turn the machine ON
by pressing the Power button
Cover cap
Less than 4 kg
- Favorite program allows you to store a customized wash cycle for future use.
- To make a Favorite program.
(1) Select a cycle.
(2) Select
The coures, washing method, number of rinses, spin speed, water temperature etc.
(3) Press and hold Favorite program button 3 econds (2 beep sounds).
The Favorite program is now stored for future use.
To reuse the program, select Favorite program and press Start/Pause.
Additional Steps
- Turn the machine off
- Leave door open to
allow drum to dry
Select a
Program
6 3 sec.
6 3 sec.
1
To activate:
press and hold the
Temp. and Rinse
button simultaneously
To deactivate:
press and hold the
Temp. and Rinse
button simultaneously
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock.
Change to the desired program, whilst in child lock mode:
6 3 sec.
2
Tub Clean
Cleaning and Maintenance
Select this function to lock the buttons on the control panel and to prevent tampering.
Press and hold the
Temp. and Rinse
button simultaneously
Cleaning the water inlet filter
Press
Select the desired
Start/Pause program
press
Start/Pause
1
2
Turn off the water
tap
Less than 5 kg
Pull out the water
inlet filter
5
Clean the filter
using a hard bristle
brush
Remove laundry
- Open the door
- Remove the laundry
[F1447TD(1~9)]
Select an Option
Pre Wash / Soak / Crease Care / Rinse+Spin
Cleaning the drain pump filter
1
2
3
4
5
Empty the drum
completly and close
the door
Add anti-limescale
(Calgon) to the main
wash compartment.
Close the disp. drawer
Power ON with
Then press and
hold Rinse and
Spin button
Press the
Start/ Pause
button to start Tub
Clean process
1
After the cycle is
complete, leave the door
open to dry
2
Open the lower
cover cap. Drain
plug to pull out the
hose
Medic Rinse
For best results or for cleaner rinsing, select the “Medic Rinse” option.
3
4
5
Remove any
extraneous matter
from the pump filter
Unplug the drain
plug. Then open the
filter by turning to
the left
After cleaning, turn
the pump filter and
insert the drain plug
Available in the Cotton, Cotton Quick, Synthetic and Half load + programs.
The respective temperature indicator will light up.
2
tu
nt
il
w
as
Once the Beep on/off function is set, the setting is memorized even after Power is off.
hi
ng
is
4 additional programs
Time Delay / Favorite / Intensive / Medic Rinse
Pull out the
dispenser drawer
The Beep on/off function can be set only during the washing cycle.
To set the Beep on/off function follow the below steps.
Press Start / Pause
to start the washing process
f in
ishe
d
Close the lower
cover cap
Cleaning the dispenser drawer
Beep on / off
1. Turn on the washing machine (by pressing the Power button).
2. Press the Start/Pause button.
3. Press and hold the Option1 and Time Delay button simultaneously for three seconds to set
Beep on/off function.
ai
Select Washing temperature
and Rinse mode
Tighten up the
inlet hose
6 3 sec.
3
4
Select the
Spinning speed
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are
washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0806.
Notes
Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.
Unscrew the
water inlet hose
4
TUB CLEAN is special cycle to clean the inside of the washing machine.
A higher water level is used in this cyle at higher spin speed. Perform this cycle regularly.
1
Less than 2 kg
3
Intensive
If the laundry is heavily soiled “Intensive”option is effective.
- By selecting the Intensive option, the washing duration may be extended,
depending on the program selected.
- To use this option, press the intensive button once before the wash program is started.
Less than 6 kg
Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufacture’s care label or instructions when washing.
Intensive: If the laundry is heavily soiled “Intensive” option is effective.
Set program at “Cotton 60°C + Intensive” option for test in accordance or in conformity with IEC60456 and EN60456.
Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic and Half load + program.
Crease Care: If you want to prevent creasing, select Crease Care option.
Medic Rinse: For best results or for cleaner rinsing, you can choose Medic Rinse option.
Warning: Keep all washing powder and detergents away from children. Danger of poisoning
Power button
C
[F1247TD(1~9)]
60°C
(Cold, 30°C, 40°C)
Favorite
Rating
1 king size (9 Tog)
- Time Delay
- Intensive
- Rinse+Spin
How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select the program you require.
- Press Time Delay button and set time required.
- Press the Start/Pause button.
3
B
Child Lock
Additional programs
Time Delay
W
ECOLOGICAL WASHING
- make use of the max. washing quantity
- do not “pre wash” if possible
- use short program if possible
B
Synthetic
Intensive 60
DRUM CARE
- remove extraneous objects
- leave door open to dry the drum
- check the rubber seals regularly
Drip dry
Additional programs
Option
1
Setting “Time Delay” determines when machine stops.
Washing program table
Delicate
WATER TREATMENT
- with hardness III water
- use water softening agent
Do not iron
Dispenser drawer
A
HANG UP WASTE WATER HOSE
Hose elbow connection e.g. attach to water tap
Sort the laundry
note washing instruction symbols Degree of soiling Type of textile / colour -
Clean the dispenser
drawer under flowing
water
Cleaning in general
Clean inside the
recess with an old
toothbrush
Insert the dispenser
drawer
5 Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry.
Important: Do not use methylated spirits, solvents or similar products.
Exterior
Proper care of your washing machine can extend its service life.
The outside of the machine can be cleaned with warm water and
a neutral non-abrasive household detergent. Immediately wipe off
any spillage. Wipe with damp cloth. Avoid striking the surface with
sharp objects. Never hose down the machine!
Interior
Dry around the washing machine door
opening, flexible gasket and door
glass. Run washing machine through
a complete cycle using hot water.
Repeat process if necessary.
Download PDF