LG | F1402FDS5 | LG F1402FDS6 Owner’s Manual

Remove Packaging
• The appliance is fitted with transit bolts to prevent internal
damage during transport. Be careful, heavy load!
• Packing and all transit bolts must be removed before using
the washing machine.
• When unpacking the base, be sure to remove the additional
packing support in the middle of the base packing.
original packing for future move.
i Store
Dispose of packing material according to local regulations.
Transit bolts
Schraubenschlüssel
1
To prevent internal damage during transport, the
special 4 bolts are locked.
If they are not removed, it
may cause heavy vibration, noise and machine to
malfunction.
2
Remove the 4 bolts
along with the rubber
bungs by slightly
twisting the bung.
Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the
washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the appliance
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
• Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
• If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
• The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
BS Plug Safety Details (For U.K. User)
E
Fuse
This appliance must be earthed As the colours of the wires in the mains lead
of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows: The green and yellow wire must
be connected to the terminal in the plug marked E or by the earth symbol or
coloured green or green and yellow. The wire coloured blue must be connected
to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal
marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
5
L
N
Cord
grip
CAUTION about the power cord
Connecting water supply hose
The hose supplied with the machine must be used. Old hoses may not be reused
3
Unscrew the 4 bolts
4
3. Die 4 Schrauben
lösen und die
using the spanner
supplied. etwas drehen, um sie
Gummipfropfen
zusammen mit den Schrauben abzunehmen.
Die 4 Schrauben und den Schraubenschlüssel
für späteren Gebrauch aufbewahren.
Close the holes with
the caps supplied.
• Die Transportsicherungsschrauben müssen vor
and the spanner for the future use. Refit transit bolts before transporting the appliance.
i Keep the 4 bolts
3
jedem Transport des Geräts wieder angebracht
werden.
• The drain hose should not be placed higher than 100 cm above the floor.
Don’t strip or crossthread when connecting inlet hose to the valve.
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
If the water supply pressure is more than 1000kPa, a decompression
device should be installed.
• If the drain hose is too long do not force back into the washing machine. This will cause unusual noise.
• Make sure the connection to taps is tight enough.
Requirements for installation site
7
Level adjustment
• Proper level-adjustment of the washing machine prevents excessive noise and vibration.
Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
• Make sure that there is no kink on the hose and
that it is not crushed.
Level floor: Permissible floor gradient under entire washing machine
is 1˚ .
When your washing machine has two valves:
• The inlet hose with the red connector is for the hot
water tap.
5 within 100 cm of either side of location of
Power socket: Must be
washing machine. Do not overload the socket with more than one
appliance.
• If the washing machine has two valves, power
saving is achieved through using hot valve.
i
If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional
type of tap for water supply. In case the faucet is square or too big, remove the spacing ring before inserting
the tap into the adaptor.
We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance
concerned, without any additional outlets or branch circuits. Check the specifications of this owner‘s manual. Do not overload
wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or
cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the
cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated
device in the mains supply.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain (gully)
in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young
children becoming trapped inside. Packaging material (e.g. plastic film, Styrofoam) can be dangerous for children. There is a risk
of suffocation! Keep all packaging well away from children.
CAUTION about the floor surface
• Periodically check the condition of the hose and
replace the hose if necessary.
4. Die Schraubenbohrungen mit den
beiliegenden Kappen verschließen.
Additional Clearance: For wall, floor and door space is needed.
(10cm: rear / 2cm:right & left side). Do not place or store laundry products on top of the washing machine at any times. They can damage
the finish or controls of the machine.
Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)
• Two rubber seals are supplied with the water inlet
hoses. They are used for preventing water leaks.
Safety instructions for use
Safety instuctions for the installation
Installation of drain hose
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person
to prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
Green and
Yellow (Earth)
Brown(Live)
Blue(Neutral)
2
6
Electrical connection
4
60 - 100 cm
1
Adjustable feet
• If the floor is uneven, adjust feet as required.
(Do not insert pieces of wood etc. under the
feet). Make sure that all four feet are stable
and resting on the floor. Then check that
the appliance is perfectly level. (Use a spirit
level).
• The installation surface must be clean, dry and level.
• Install washing machine on a flat hard floor.
• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
• The washing machine must be perfectly level and firmly in position.
• It must not “see-saw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
@
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating
instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these
operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold
drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper and
may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect
by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been
used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain in
the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflammable gas.
Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
G
Technical Specification
arantiebedingungen
Disposal
Name of product
Front loading washing machine
Max. Watt
2100 W (Wash) / 1100 W (Steam)
Power supply
220-240 V~, 50 Hz
Wash capacity
9 kg
Size WxDxH mm:
600 x 640 x 850
Water consumption
59 l (6.5l / kg)
Weight
65 kg
Permissible water pressure 1.0-10 bar (100-1000kPa)
• When this crossed-out wheeled bin symbol is attached to a product it means the product is covered Entsorgung von Altgerätenby European Directive 2002/96/EC.
1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers
•aufAll
electrical
electronic
products
should
einem
Produkt and
angebracht
ist, unterliegt
dieses
Produktbe disposed of separately from municipal waste stream dervia
europäischen
Richtlinie
2002/96/EC.
designated
collection
facilities
appointed
by the government or the local authorities.
2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom
über dafür
staatlich of
vorgesehenen
Stellen entsorgt
•Hausmüll
The correct
disposal
your old appliance
will help prevent potential adverse consequences for the werden.
and human
health.
3. Mitenvironment
der ordnungsgemäßen
Entsorgung
des alten Geräts
Sie Umweltschäden
und eine about
Gefährdung
der of your old appliance, please contact your city office, •vermeiden
For
more
detailed
information
disposal
persönlichen Gesundheit.
4. Weitere
zur Entsorgung
altenwhere
Geräts you purchased the product.
wasteInformationen
disposal service
or thedes
shop
erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt
oder in dem Geschäft, wo Sie das Produkt erworben haben.
N
Troubleshooting
Symptom
Possible Cause
Solution
• Water supply is not adequate in area
• Water supply taps are not completely open.
• Water inlet hose(s) are kinked.
• The filter of the inlet hose(s) are clogged.
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
• The drain filter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information,
please refer to “Cleaning the drain pump filter”
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning
• Is the door opened or not
completely closed?
tE
Owner‘s Manual
F1402FDS(1~9)
Close the door completely.
If “
” is not released, call for service.
Unplug the power plug and call for service.
FE
• Water overfills due to the faulty water
valve.
PE
• Water level sensor has malfunctioned.
LE
• Over load in motor.
AE
• Water leaks
Call for service.
PF
• The washer experienced a power failure.
Restart the cycle.
Close the water tap.
Unplug the power plug.
Call for service.
Rattling and clanking noise
Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound
Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise
Have all transit bolts and packing been removed?
Water leaks.
Check and tighten hose connections. Unclog drain pipe.
Contact plumber if necessary.
Excessive suds
Too much detergent or unsuitable detergent.
Washing machine does not start
Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin
Check that the door is firmly shut.
Door does not open
Once started, the door can not be opened for safety reasons.
Wait one or two minutes before opening the door to allow the electric
locking mechanism time to release.
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.
For the U.K. customer
CUSTOMER SERVICES Tel. : 0870 - 873 - LGLG (5454) Fax. : 0870 - 872 - 7337
LGEUK SERVICE WEB-SITE : http://uk.lge.com
P/No. :MFL38868793
Preparation
Washing symbols
CHECKING THE MACHINE
Never use a defective machine! In case of any
failure, first unplug the machine and turn off the
water tap.
A
- empty all pockets
- remove all metal parts
- place the delicate textiles into the laundry net
- close zippers
Do not
tumble dry
Dry flat
Do not wash
Hot ironing
Hang to dry
Do not bleach
Main Wash
For very dirty clothes fill 1/4 of the
portion of detergent in here and
select a prewashing programm
WATER TREATMENT
- with hardness III water
- use water softening agent
Softener
Do not exceed the MAX-Level.
Highly densed softeners are to
be diluted with some water.
C
Pre Wash
For normal dirty clothes use a small
amount of detergent. Don't pre wash.
Mount the level plate to use fluid detergents.
Program
Cotton
Cotton
Quick
Synthetic
Allergy
Care
Delicate
Hand Wash
/Wool
Quick 30
Fabric Type
Color fast garments (shirts,
nightdresses, pajamas...)and
lightly soiled white cotton
(underwear)
Lightly soiled clothing and
small loads
Water Temp.
(Option)
60°C
(Cold, 30°C,
40°C, 95°C)
40°C (Cold,
30°C, 60°C)
Polyamide, Acrylic, Polyester
40°C (Cold,
30°C, 60°C)
Lightly soiled baby wear
60°C
(40°C, 95°C)
Cotton, underwear, pillow
covers, bed sheets,
baby wear
60°C
Delicate laundry easily
damaged
30°C
(Cold, 40°C)
“Hand wash” marked delicate
and wool laundry
40°C
(Cold, 30°C)
Colored laundry which is lightly
soiled fast
30°C
(Cold, 40°C)
Option
-
Time Delay
Steam Wash
Intensive
Soak
Pre Wash
Crease Care
Rinse+Spin
Medic Rinse
-
Time Delay
Steam Default
Intensive
Crease Care
Rinse+Spin
Medic Rinse
-
Time Delay
Intensive
Crease Care
Rinse+Spin
Fill the drum
Check the folds of the flexible gasket (grey) and remove any small articles, if any. .
Check inside of the drum and remove any left in items for next wash cycle. .
Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages .
2
Control panel
Dispenser
drawer
Power button
Start / Pause
Options
Fill detergent
Refer to the
written information
on the detergent's packing
B
Drum
H ow to use washer
Available in the Cotton, Cotton Quick, Synthetic, Allergy Care and Baby Care programs.
Medic Rinse is set by default in the Baby Care program.
2. Steam Wash
The respective temperature indicator will light up.
Less than 7 kg
Steam Washing and Refresh cycle
Turn the machine ON
by pressing the Power button
Cover cap
Refresh
Less than 4.5kg
Select the
Spinning speed
Remove laundry
- Open the door
- Remove the laundry
w
Temperature
Program
Cotton
Cold, 30°C, 40°C, 60°C, 95°C
Baby Care
Cotton Quick
Cold, 30°C, 40°C, 60°C
Refresh
Synthetic
Cold, 30°C, 40°C, 60°C
Allergy Care
as
hi
ng
60
95°C
40
60
30
40
Cold
30
is
Press Start / Pause
to start the washing process
f in
ishe
Cotton
Program
How to use Refresh Cycle
il
30
Time Delay / Steam
Wash95°C
/ Intensive / Medic Rinse
Cold
nt
Notes
Neutral detergent is recommended. The wool cycle features gentle tumbling and low-speed spin for garment care.
Tub Clean
Cotton Quick
Synthetic
1
2
d
Select the Refresh
program
Load 3 items or less
and close the door
Cotton
60°c (30°c, 40°c, 95°c)
Temperature
Synthetic
40°c (30°c, 60°c)
Baby Care
95°c (40°c, 60°c)
40°C,
60°C,
95°C
• This option features upgraded washing
performance with low energy.
No choose
• Do not load delicates such as wool, silk, and
60°C easily discolored clothes.
NOTE:
- Steam wash is a highly concentrated and
efficient. Press the
It may seem there is no water inside the
3
4 Start/Pause
drum(normal
condition).
- During thebutton
steam cycle the strong steam
spray may not be seen through the door
(normal condition).
Press the Steam Wash button
repeatedly until the
- During the steam operation, a spraying sound
required and correct number
displayed
will of
beitems
heard.is(normal
condition)
- Do not try to open the door while operating.
Steam can cause severe burns.
Select the desired
program
press
Start/Pause
1
2
3
Unscrew the water
inlet hose
4
Pull out the water
inlet filter
5
Clean the filter using
a hard bristle brush
Tighten up the inlet
hose
TUB CLEAN is special cycle to clean the inside of the washing machine.
A higher water level is used in this cyle at higher spin speed. Perform this cycle regularly.
Cleaning the drain pump filter
6 3 sec.
1
2
3
4
5
1
2
3
4
5
3. Intensive
thedrum
laundry is heavily
soiled “Intensive”
Empty• Ifthe
Add anti-limescale
option is effective.
completly
and close (Calgon) to the main
• By selecting the Intensive option, the wash
the door
washdepending
compartment.
time may be extended,
on the
program selected. Close the disp. drawer
Power ON with
Then press and
hold Rinse and
Temp. button
Press the
Start/ Pause
button to start Tub
Clean process
After the cycle is
complete, leave the
door open to dry
Open the lower cover Unplug the drain plug.
Then open the filter
cap. Drain plug to
by turning to the left
pull out the hose
Remove any
extraneous matter
from the pump filter
After cleaning, turn
the pump filter and
insert the drain plug
Close the lower
cover cap
• To use this option, press the intensive button
once before the wash program is started.
Cleaning the dispenser drawer
4. Medicthe
Rinse
Changing
language
Steam Wash is
Steam Wash is
• For tough stained clothes, underwear, or baby
- For heavily stained clothes, underwear, or baby clothes.
clothes.
1
available with Cotton, Synthetic,
- Steam Wash is available with the Cotton, Cotton Quick, Synthetic, Baby Care,• Steam
AllergyWash
Care is
programs.
Baby Care program.
- Refresh cycle is always Steam wash.
Refresh cycle is fixed Steam wash.
- Do not load delicates such as wool, silk, and easily discolored clothes.
Program
Temperature
Pre Wash
Soak
Rinse + Spin
Baby Care
Press
Start/Pause
Turn off the water
tap
Steam Washing features enhance washing performance with low
pressing the
Steam Wash button, Steam
energy consumption. Refresh cycle reducesBycreases
in clothes.
Function Can be selected.
By pressing the Steam Wash button, Steam Function
can
be
selected.
When Steam Function is selected, Steam wash
) LED lights
When Steam Function is selected, Steam wash ( (
lights on.
up.
tu
washed according to the instructions on the garment label and those issued by the manufacturer of this washing machine M0708.
Allergy Care
Additional Steps
- Turn the machine off
- Leave door open to
allow drum to dry
Select a
Program
Note:
To use programs in the
Steam-Cycle, please press
first the “Steam Wash” button
(see additional programs).
Press and hold
the Option buttons
simultaneously
For best results or for cleaner rinsing, select the “Medic Rinse” option.
Turn off tap
- Close water supply
- Clean the machine
- Unplug machine
C
Cleaning the water inlet filter
6 3 sec.
Medic Rinse
3
A
To deactivate:
press and hold
the Option buttons
simultaneously
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric shock.
Change to the desired program, whilst in child lock mode:
2
To activate:
press and hold
the Option buttons
simultaneously
If the laundry is heavily soiled “Intensive”option is effective.
- By selecting the Intensive option, the washing duration may be extended,
depending on the program selected.
- To use this option, press the intensive button once before the wash program is started.
Temperature
Rating
Less than 2.0kg
6 3 sec.
1
Intensive
Program Cycle
Cleaning and Maintenance
Select this function to lock the buttons on the control panel and to prevent tampering.
6 3 sec.
How to set “Time Delay”
- Press Power button.
- Turn the Program dial to select the program you require.
- Press Time Delay button and set time required.
- Press the Start/Pause button.
Rinse
Maximum Load
Less than 3.0kg
Child Lock
Additional programs
Time Delay
Pre Wash
Crease care
Cotton mixed, Polyester mixed
Soak
Pre
Wash
- Steam Default
No Choose
Refresh
3 items
Dress shirts, blouses
Pre Wash
Rinse++ Hold
Select an Option
Soak
Soak
Normal + Hold
Pre Wash / Soak / Crease Care / Rinse + Spin
Rinse ++
Water Temperature: Select water temperature to suit wash cycles. Always follow garment manufacture’s care label or instructions when washing.
Rinse + Spin
Rinse + Spin
Rinse +
Crease+ care
Spin
Intensive: If the laundry is heavily soiled “Intensive” option is effective.
Crease care Rinse
Normal
Crease
care
Set program at “Cotton 60°C + Steam Wash + Intensive” option for test in accordance or in conformity with EN60456 and IEC60456.
95°C
Rinse++ Hold
+
60
Pre Wash: If the laundry is heavily soiled, “Pre Wash” Cotton is recommended. Pre Wash is available in the Cotton, Cotton Quick, Synthetic and Baby Care program.
Select Rinse mode Normal +++Hold Rinse + Hold
40
+
Rinse
Normal
+
Hold
Hold
and Washing temperature Rinse + Rinse +++
Crease Care: If you want to prevent creasing, select Crease Care option.
30
Rinse+ Hold
Normal
Cold
Normal
Medic Rinse: For best results or for cleaner rinsing, you can choose Medic Rinse option. Medic Rinse is set by default in the Baby Care program.
+
Rinse++
Rinse
+
Normal
95°C
Rinse
The wool wash cycle of this machine has been approved by Woolmark for the washing of machine washable Woolmark products provided that the products are
60
4 additional programs
Normal
40
Warning: Keep all washing powder and detergents away from children. Danger of poisoning
Spinning cycle
ai
ECOLOGICAL WASHING
- make use of the max. washing quantity
- do not “pre wash” if possible
- use short program if possible
B
Display
W
DRUM CARE
- remove extraneous objects
- leave door open to dry the drum
- check the rubber seals regularly
Handy to bleach
Drip dry
Additional programs
Steam Cycle
1
Setting “Time Delay” determines when machine stops.
Washing program table
Baby Care
LAUNDRY WITH DIFFERENT AMOUNTS OF
SOILING
- wash new textiles separately
lightly
- do not prewash
- pretreat dirty spots
heavily
- pre wash
Do not iron
Dispenser drawer
HANG UP WASTE WATER HOSE
Hose elbow connection e.g. attach to water tap
DOING LAUNDRY AND USING MACHINE
WITH CARE
Medium hot
ironing
Luke warm ironing
WATER CONNECTION
Turn on the water tap
INSERT PLUS INTO THE MAINS SOCKET
Never touch the plug with wet hands!
Never remove the plug from the socket by pulling on the cord.
Washing
temperature
Sort the laundry
note washing instruction symbols Degree of soiling Type of textile / colour -
• For high effectiveness or more purity in rinse
operation you can choose Medic Rinse option.
• Available in Cotton, Synthetic and Baby Care
6 3 sec.
program.
• Medic Rinse is default in Baby Care program.
The required temperature
2 lamp will light up for 3
identification.
1
4
Refresh
� machine
Refresh cycle Press and hold the
Turn on
• For slightly
clothes simultanewhich have
by pressing
the wrinkledbuttons
extended
for time.
3 seconds
power been
buttonstored for an ously
Display shows the
different languages
Select your
language
Acknowledge your
selection
It just makes wrinkled clothes easy to iron
(Do not load wet clothes).
• Wrinkles will be reduced.
The Beep on/off function can be set by pressing and
holding the Option and Rinse button simultaneously.
The Beep on/off function can be set at any time and it is
automatically cancelled in the event of a power cut.
The Beep on/off function also works when power is off.
Press the
Steam Wash button
Pull out the
dispenser drawer
3
Clean the dispenser
drawer under flowing water
Cleaning in general
� How to use Refresh cycle
Beep
/ washer
off and select the Refresh program.
1. Turnon
on the
2. Load 3 items or less and close the door.
3. Press the Steam Wash button repeatedly until
the desired and correct number of items is
displayed. Initial display is 2 items
2
4
5
Clean inside the
recess with an old
toothbrush
Insert the dispenser
drawer
5 Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry.
Important: Do not use methylated spirits, solvents or similar products.
Exterior
Proper care of your washing machine can extend its service life. The
outside of the machine can be cleaned with warm water and a neutral
non-abrasive household detergent. Immediately wipe off any spillage.
Wipe with damp cloth. Avoid striking the surface with sharp objects. Never
hose down the machine!
Interior
Dry around the washing machine door
opening, flexible gasket and door glass.
Run washing machine through a complete
cycle using hot water. Repeat process if
necessary.
Download PDF