LG | WD-12311RD | LG WD-12311RD Owner’s Manual

P
roduct Feature
Direct Drive
System
The advanced Brushless DC motor
belt and
directly
drives the drum without
pulley.
Water Circulation
Spray detergent
Clothes
are
solution and water onto the load
soaked
more
quickly
and
The
detergent suds can be removed
shower during rinse cycle. The water
water and detergent more efficiently.
over
and
over.
thoroughly during
more easily by the
wash
circulation system
uses
cycle.
water
both
Built-in Heater
Internal heater
on
selected
automatically
cycles.
heats the water to the best temperature
Child Lock
The Child lock prevents children from
the
any button to
pressing
change
settings during operation.
Jumbo drum
40%
LG's jumbo drum can wash about 40% more load than conventional
washing machines. A bigger drum improves the wash performance.
More economical
Intelligent
Wash
by Intelligent
System
Wash
System
detects the amount of load and water
temperature, and then determines the optimum
washing
time to minimize energy and water
Low noise
speed
control system
the amount of load and balance, it
to minimize the spinning noise level.
By sensing
water level and
consumption.
evenly
distributes load
Auto Restart
If the washing machine is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
C
ontents
Warnings ............................................................................................................3
Specification ........................................................................................................5
Installation ...........................................................................................................6
Care before washing .........................................................................................12
Adding detergent...............................................................................................13
Function
How to
..........................................................................................................14
use
washer............................................................................................15
Maintenance......................................................................................................23
Troubleshooting guide.......................................................................................26
Terms of Warranty ............................................................................................29
2
W arnings
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
!
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock,
the washer, follow basic
?
Do not install
be
?
?
exposed
or
precautions, including
store the washer where it will
the
?
?
?
?
oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may
ignite or explode.
To avoid such a result, carefully follow the
?
garment manufacturer's wash and
out.
instructions.
Keep the area underneath and around your
appliances free of combustible materials such
?
any other appliance.
Do not leave the washer door open.
An open door could entice children to
?
Do not slam the washer door closed
or
try
to
To minimize the
possibility of electric shock,
unplug this appliance from the power supply or
disconnect the washer at the household
distribution
or
or
care
force the door open when locked. This could
result in damage to the washer.
as
lint, paper, rags, chemicals, etc.
Close supervision is necessary if this appliance
is used by disable or young children.
Do not allow children to play on, with, or inside
the door
?
dry articles that have been
that you understand and have the skills to carry
this
?
or
wax,
recommended in the user-maintenance
published user-repair instructions
Do not wash
cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as
to the weather.
or
injury to persons when using
following:
Do not tamper with controls.
Do not repair or replace any part of the washer
or attempt any servicing unless specifically
instructions
or
hang
on
crawl inside the washer.
?
Never reach into washer while it is
moving. Wait
until the drum has completely stopped.
The laundry process can reduce the flame
retardant of fabrics.
?
panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
dryer is intend only for drying textile material in
water.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
grounded. In the event of malfunction or breakdown, grounding will reduce the risk
by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
Do not use an adapter or otherwise defeat the grounding plug.
This
appliance
must be
of electric shock
?
?
If you don't have the proper
WARNING :
outlet, consult
an
electrician.
Improper
connection of the equipment-grounding conductor can result in risk of electric
qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
shock. Check with
a
-
3
W arnings
To minimize the risk of fire in
?
a
tumble
dryer,
the
following
spotted or soaked with vegetable
placed in a tumble dryer.
Items that have been
or
should be observed:
cooking
oil constitute
a
fire
hazard and should not be
Oil-affected items
sources
Such
ignite spontaneously, especially when exposed
dryer. The items become warm, causing
can
in
as
a
tumble
to heat
an
oxidation
reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can
become hot enought to catch fire. Piling, stacking or storing oil-affected items can
prevent heat from escaping and
so
create a fire hazard.
If it is unavoidable that fabrics that contain
vegetable or cooking oil or have been
products be placed in a tumble dryer they should first be
washed in hot water with extra detergent-this will reduce, but not eliminate, the
hazard. washed in hot water with extra etergent-this will reduce, but not
eliminate, the hazard. The 'cool down' cycle of tumble dryers should be used to
reduce the temperature of the items. They should not be removed from the tumble
dryer or piled or stacked while hot.
contaminated
?
?
by
hair
care
Items that have been previously cleaned in, washed in, soaked in or spotted with
petro/gasoline, dry-cleaning solvents or other flammable or explosive substances
should not be placed in a tumble dryer.
Highly flammable substances commonly used in domestic environments include
acetone, denatured alcohol, petrol/gasoline, kerosene, spot removers (some
brands), turpentine, waxes and was removers.
Items
containing
foam rubber
foam) or similarly testured
dryer on a heat setting.
heated, produce fire by spontaneous combustion.
(also
known
as
rubber. like materials should not be dried in
Foam rubber materials can, when
?
Fabric softeners
a
latex
tumble
products should not be used in a tumble dryer to eliminate
electricity unless this practice is specifically recommended by the
the fabric softener or product.
or
similar
the effects of static
manufacturer of
?
Undergarments
dryer.
that contain metal reinforcements should not be
placed
Damage to the tumble dryer can result if metal reinforcements come
drying. When available a drying rack could be used for such items.
?
Plaxtic articles such
be
?
placed
in
a
as
tumble
shower caps
or
babies
waterproof napkin
loose
covers
a
tumble
during
should not
dryer.
Rubber-backed articles, clothes fitted with foam urbber pads,
rubber-coated tennis shoes should not be placed in a tumble
4
in
pillows, galoshes
dryer.
and
S pecification
Name
:
Front
:
220-240V~,50Hz
Size
:
600mm(W)×645mm(D)×850mm(H)
Weight
:
66kg
:
8kg(2100W)
:
4kg(1500W)
:
No
spin/400/800/1000/1200 [WD-12311RD/WD-12316RD]
No
spin/400/800/1000/1400 [WD-14311RD/WD-14316RD]
Power
Wash
supply
capacity/Max.
Dry capacity/Max.
Watt
Spin speed
Water
Watt
consumption
The appearance and
:
loading washing
machine
144ℓ(18ℓ/ kg )[WD-14311RD/WD-14316RD]
148ℓ(18.5ℓ/ kg ) [WD-12311RD/WD-12316RD]
specifications may
be varied without notice to raise the units
quality.
Accessories
5
nstallation
I
Install
or
store where it will not be
exposed
to
temperatures below freezing
or
exposed
to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine
carpeted floor.
In countries where there
vermin, pay particular
are areas
attention to
is installed
on a
which may be subject to infestation by cockroaches or other
keeping the appliance and its surroundings in clean condition at
all times.
Any damage which may
appliance guarantee.
be
cause
by
cockroaches
or
other vermin will not be covered
by
the
Transit bolts
appliance is fitted
The
?
Packing
with transit bolts to
prevent internal damage during transport.
and all transit bolts must be
removed before
using
the washer.
When
unpacking the base, be sure
to remove the additional packing
support in
packing.
the middle of the base
Removing
transit bolts
1. To
prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts
?
If
they
are
along
not
with the rubber
removed, it may
the spanner
6
supplied.
along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future
use.
bungs.
cause
vibration, noise and malfunction.
2. Unscrew the 4 bolts with
3. Take out the 4 bolts
heavy
?
Whenever the
appliance is transported, the
transit bolts must be refitted.
4. Close the holes with the caps
supplied.
I
nstallation
Installation place requirement
Level floor
:
Allowable slope under entire washer is 1˚
Power outlet :
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with more than one
appliance.
Additional Clearance
:
For wall, door and floor
(10cm
modeling is required.
/2cm:right & left side)
place or store laundry products on top
: rear
Do not
of washer at
any times.
They
can
damage
the finish
or
controls.
Positioning
Install the washer
on a
flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
Before placing the washer on tiles, apply a rubber mat under the feet.
?
?
?
?
?
?
Never try to correct any
washer.
unevenness
in the floor with
pieces of wood,
cardboard
or
similar materials under the
If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an insulating(85x60cm)
covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliance.
The washer must not be installed in rooms where the temperature can drop below 0°C.
Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of
a
breakdown.
With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable,
and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top.
BS
Plug Safety Details (For
U.K.
User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This
Green and
appliance
must be earthed
Yellow(Earth)
E
Brown(Live)
L
Blue(Neutral)
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E
or by the earth symbol
or coloured Green or Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or coloured Black.
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L or coloured Red.
If
a
13 amp
(BS 1363) plug
is used, fit
a
13 amp BS 1362 fuse.
7
I
nstallation
Electrical connection
1. Do not
3.
4.
5.
?
?
?
extension cord
double
adapter.
supply
replaced by the manufacturer or its service agents
damaged,
or similarly qualified person in order to avoid a hazard.
Always unplug the machine and turn off the water supply after use.
Connect the machine to an earthed socket in accordance with current wiring regulations.
The appliance must be positioned so that the plug is easily accessible.
2. If the
use an
cord is
or
it must be
Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen
hoses may burst under pressure. The reliability of the electronic control unit may be impaired at
temperatures below freezing point.
If the appliance is delivered in the winter months and temperatures are below freezing : Store the
washing machine at room temperature for a few hours before putting it into operation.
Washing Machine
is to be connected to the water mains
sets and that old hose-sets should not be used.
Connecting
water
using
new
hose-
supply hose
▶Water supply pressure
30kPa and 1000kPa
▶Don't strip
Inlet hose
must
be between
(0.3~10kgf/cm2)
crossthread when
the valve.
or
to
connecting
▶If the water supply pressure is more than
1000kPa, a decompression device should be
installed.
?
Two rubber seals
are
supplied
with the
water inlet hoses these are in order to
prevent
?
water leaks.
Check water tightness of washing
machine connections by turning the tap
completely
?
on.
Periodically check the condition of the
replace the hose if necessary.
hose and
?
Make sure that there is no kink
hose and that it is not crushed.
▶When your washer has
?
?
8
two
on
the
valves,
The Inlet hose which has red connector is
for the hot water tap.
If the washer has two valves, the energy
is saved by using hot valve.
nstallation
I
Normal Tap without thread &
1. Unscrew the fixing
attach the tap.
screw
to
screw
2. Push the
rubber
with
type inlet hose
connector up till the
packing is
3. Push the
water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
in
tight contact
the tap. Then tighten the 4
screws.
Normal Tap without thread &
1. Untighten the upper
connector
screw.
?
In
case
large
one
touch type inlet hose
2. Push the upper connector up till
the rubber packing is in tight
contact with the tap. Then
tighten the 4 screws.
3. Connect the
water
supply hose
to the middle connector,
pushing the plate down.
the diameter of the tap is
the guide plate.
remove
?
Turn the middle connector not
to have water leaked.
?
Make
sure
that the rubber seal
is inside the hose connector.
?
To separate the water supply
hose from the middle connector
shut off the tap. Then pull the
inlet hose down, pushing the
plate down.
?
Your machine
comes
with
only
cold water connection.
?
Make
sure
that there
are no
kinks in the hose and that it is
not crushed.
9
nstallation
I
This
equipment
is not
designed
for maritime
use or
for
use
mobile installations such
as
caravans, aircraft etc.
stopcock if the machine is to be left for any length of time (e.g. holiday),
especially if there is no floor drain(gully) in the immediate vicinity.
When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the
door lock to prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
of suffocation ! Keep all packaging well away from children
Turn off the
Installation of drain hose
?
When
installing the drain hose sink,
it tightly with a string.
Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
secure
?
?
The drain hose should not be
than 100
?
cm
Proper securing of the
damage
the floor from
?
drain hose will protect
due to water
When the drain hose is too
long,
back into the washer. This will
noise.
10
placed higher
above the floor.
leakage.
do not force
cause
abnormal
I
nstallation
Level
adjustment
1.
Adjusting
the
washing
machine level
properly prevents
excessive
noise and vibration.
Install the
corner
appliance
of the
Timber
NOTE
on a
solid and level floor surface,
2. If the floor is uneven,
pieces
Make
sure
After the
errors.
adjust the adjustable
feet)
that all four feet
washer is
In the
case
platform,
stable and
are
appliance
level, tighten
is
feet
as
required. (do
perfectly
not
resting on the floor and
(use a spirit level)
level.
the lock nuts up towards
the washer. All lock nuts must be
NOTE
a
of wood etc. under the
then check that the
※
in
may contribute to
suspended type flooring
or
excessive vibration and unblance
insert
preferably
room.
of the
base
of
tightened.
that the
washing machine is installed
securely fastened in order
risk that it might fall off.
on a
raised
it must be
to eliminate the
Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the machine
should not move up and down at all. (Please, check both of two directions)
If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
Concrete
floors(tile...)
?
The installation surface
?
Install washer
?
Before
on a
placing
must
be
clean, dry and level.
flat hard floor.
the washer
on
tiles, apply a rubber
mat
under the feet.
Do not let the feet of the washer get wet. If feet of the washer get wet,
※
slipping
Wooden floors
Wooden floors
?
are
Rubber
particularly susceptible
to
If
?
possible
install the washer in
one
of the
corners
※
Insert the rubber cups to reduce vibration.
※
You
?
?
can
obtain the rubber cups
Cup
vibration.
To prevent vibration we recommend you place rubber cups under each foot,
at least 15mm thick under the washer, secured to at least 2 floor beams with
?
occur.
may
of the
room,
screws.
where the floor is
(p/no.4620ER3001B) from
more
the LG spares
stable.
dept.
Important!
Proper placement and levelling of the washer ensure long,regular and reliable operation.
The washer must be absolutely horizontal and stand firmly in position.
?
It must not "Seesaw"
?
The installation surface
across corners
must
under load.
be clean, free from floor wax and other lubricant coatings.
11
C
are
before
washing
Caring before washing
1. Care Labels
Look for
garment
2.
label on your clothes. This will tell you about the fabric content of your
and how it should be washed.
a care
Sorting
To
get the best results, Sort clothes into loads that
can
be washed with the
same
wash
cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always sort dark colors from pale colors and whites. Wash separately as dye and lint
transfer
Soil
causing discoloration of white
lightly soiled one.
can occur
soiled items with
(Heavy, Normal, Light)
(White, Lights, Darks)
(Lint producers, Collectors)
Color
Lint
3.
Caring
before
etc. If
possible, do
not wash
heavily
Separate clothes according to amount of soil.
Separate white fabrics from colored fabrics.
Wash lint producers and lint collectors
separately.
loading
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
?
Check all pockets to make sure
they are empty. Items such
that
as
nails, hair clip, matches, pens,
coins and
keys
can
damage
both
your washer and your clothes.
?
Close zippers, hooks and strings to
make sure that these items don't
snag
?
on
other clothes.
Pre treat dirt and stains
a
little
detergent
by brushing
dissolved in water
onto stains like collars and cuffs to
help shift dirt.
12
A dding detergent
Adding detergent and fabric softener
1. The Dispenser Drawer
3. Detergent
?
The
dosage
detergent should be used according to
of the detergent manufacture.
the
instruction
?
If too
much
detergent
is used
recommended amount,
occur
heavy
malfunction)
Use powder
loading
?
Main wash
only
U
?
?PreWash+MainWashU
2.
more
load to the
than the
many suds
and this will decrease the
or cause
?
too
can
washing result
(Causing a
motor.
detergent only for the front
washer.
Detergent usage may need to be adjusted
for water temperature, water hardness,
size and soil level of the load. For best
results, avoid oversudsing.
Adding Fabric Softener
Tips
Full load
according
:
to
manufacturer's recommendation.
Part load
?
Do not exceed the maximum fill line.
Overfilling
can cause
clothes.
?
:
1/2 of full load.
?
Detergent is flushed from the dispenser at
beginning of the cycle.
the
Do not leave the fabric softener in the
detergent drawer for more than
(Fabric softener could harden)
?
3/4 of the normal amount.
early dispensing
of the fabric softener which could stain
?
:
Minimum load
2
days.
Softener will automatically be added
during the last rinse cycle.
Do not open the drawer when water is
supplied.
?
Solvents(benzene, etc)
are
not
allowable.
NOTE
Do not pour fabric softener
on the cloths
directly
13
F
unction
Recommended
Fabric
Program
according
courses
to the
Proper
Temp.
(Option)
Type
Color fast garments
Cotton-Eco
Maximum
Load
is the
in Cotton.
(Cold,
30˚C, 40˚C,
95˚C)
Laundry type
same
Option
Time
in
Minutes
60˚C
(shirts, night dresses,
pajamas...)and lightly soiled
white cotton (underwear...)
Cotton
laundry type
Rating
110
Rating
120
4.0kg
75
3.0kg
65
2.0kg
55
2.0kg
50
5.0kg
30
Soak
Pre Wash
Rinse+Spin
Spin only
Dry only
60˚C
(40˚C)
Intensive
Synthetic
Delicate
40˚C
Polyamide, Acrylic,
Polyester.
(Cold,
30˚C,60˚C)
Delicate laundry easily
damaged.
30˚C
(Cold, 40˚C)
Machine washable woolens
Wool/Silk with
pure new wool only.
Hand
Wash
"Hand Wash" marked
delicate and wool laundry.
Colored Landry which
Quick 30 is
lightely soiled fast.
30˚C
(Cold, 40˚C)
Rinse+Spin
Spin only
Intensive
Cold
(30˚C,40˚C)
30˚C
(Cold, 40˚C)
Rinse+Spin
Spin only
Dry only
Intensive
Duvet
Cotton
bedding
with
filling,
duvet, pillow, blanket, sofa
cover
Water
with
light filling.
Temperature
:
Cold
(30˚C, 40˚C)
Rinse+Spin
Spin only
Intensive
1
king size
(9 Tog)
60
Select the water temperature to the wash cycles.
manufacture's care label or instructions when
Always follow garment
laundering.
Intensive
If the
:
Program setting
laundry
is
heavily
with "Intensive"
soiled "Intensive"
option
option
is effective.
for test in accordance
or
in
conformity with
EN60456
and IEC 60456.
Pre Wash
14
:
If the laundry is heavily soiled, "Pre Wash" Cotton is recommended. Pre Wash is
available in Cotton, Cotton-Eco and Synthetic Program.
H
ow
1. Cotton
to
use
washer
selected upon power
?
?
?
2. Manual
automatically
Press the
Power(
) button
Press the
Start/Pause(
to start.
) button.
Initial condition
-
Wash
:
Main wash
-
Rinse
:
3 times
on.
?
?
Press the
Selecting
Power(
) button
to start.
Select the conditions which you want to
use, by pressing each button.
For
selecting the each conditions, please
refer to the page16~page22
?
Press the Start/Pause button.
-Spin:
[WD-14311RD/WD-14316RD]
1400 rpm
[WD-12311RD/WD-12316RD]
1200 rpm
-
-
Water temperature
:
60˚C
Program : Cotton
15
H
ow
to
use
(1)
(1)
(2)
(3)
(4)
Button
Dial
:
:
washer
(2)
Power
(5)
(6)
(7)
(8)
Program
Button
:
Start/Pause
Button
:
Option
(3)
Child lock
(4) (5)
Button
:
Rinse
Button
:
Button
:
Spin
Temperature
(6)
(7)
(8)
(9)
(10)
(11)
(9) Button : Dry
(10) Button : Intensive
(11) Button : Time Delay
Power
Program
1. Power
?
Press the
Power(
)
button to turn power
?
(Program)
on
and off.
?
To cancel the Time
Power(
)
button
Delay function, the
should be pressed.
9 programs
2. Initial Program
-
Cotton
-
Cotton-Eco
-
-
?
When the
washer is
Power( ) button is pressed, the
ready for Cotton program. And the
other initial conditions
?
as
follows.
So, if you want to advance into the washing
cycle without changing the program, just press
Start/Pause( ) button and then the washer
will
proceed.
Initial program
[WD-14311RD/WD-14316RD]
-Cotton Program / Main Wash /
Normal Rinse / 1400 rpm / 60˚C
[WD-12311RD/WD-12316RD]
-Cotton Program / Main Wash /
Normal Rinse / 1200 rpm / 60˚C
16
are
available
according
to the
laundry type.
-
?
?
-
-
Synthetic
Delicate
Hand Wash
Quick 30
-
Duvet
-
Drain
Wool/Silk
Lamp
will
When
Start/Pause( ) button is pressed,
automatically selected.
light
up to indicate selected program.
the
Cotton program is
-
the
By turning
Program dial,
selected in order of "Cotton
Synthetic
Quick 30
-
-
Delicate
Duvet
-
-
the program is
Cotton-Eco
-
Wool/Silk
-
-
Hand Wash
Drain".
Regarding to the laundry type for each program
Please refer to the page14.
ow
H
to
use
washer
Start/Pause
Option
By pressing the option
one option
?
button, only
function be selected.
1. Start
?
This Start/Pause button is used to start
wash
cycle
or
pause the wash
cycle.
2. Pause
?
?
?
1. Soak
If temporary stop of wash cycle is needed,
press "Start/Pause" button.
When in Pause, the power is turned off
automatically after 4 minutes.
NB. The door will not open before 1 to 2
minutes when Pause is selected,
or
at the end of the wash
Use this mode to wash normal clothes
?
and
heavy
clothes which
are
Available in Cotton, Cotton-Eco and
?
or
thick
excessively dirty.
Synthetic.
2. Pre Wash
?
cycle.
Use this
option
for load that need
pretreatment. Add 16 minutes pre wash and
drain.
-
When
using Pre Wash option, do not use
liquid detergent in the main wash
comportment. Use powder for the main
wash.
?
Available in Cotton, Cotton-Eco and
Synthetic.
3. Rinse+Spin
?
Use this
option
4. Spin
?
to rinse and then
spin.
only
When you want
spin only,
select the this
option.
5.
?
Dry only
When you want
Dry only,
select the this
option.
?
Available in Cotton, Cotton-Eco,
and Quick 30.
Synthetic
17
H
ow
to
use
washer
Child lock
Rinse
?
By pressing the Rinse
button, the Rinse type
can
be selected.
If you choose to lock the buttons on the
control assembly to prevent tampering, this
function may be selected.
-
Normal
-
Rinse+
-
Rinse++
-
Normal+Hold
-
Rinse++Hold
1. Child lock
1. Normal
?
Child lock
by pressing and holding the
and
Rinse
button
simultaneously.
Option
(About three seconds)
can
be set
?
Cotton / Cotton-Eco /
Synthetic performs 3
Rinses
?
Wool/Silk / Hand Wash
/Quick 30 / Delicate /
Duvet / performs 2 Rinses
?
When child lock is set, all buttons
are
inoperable.
2. Rinse+ & Rinse++
?
?
To deactivate Child lock system, press and hold the
Option and Rinse button simultaneously again.
(About three seconds)
Used to additional rinse, which may assist
removing traces of detergent residue.
in
?
By selecting Rinse+
or
Rinse++ function,
the Rinse Time and the Rinse water
are
increased.
3. Rinse Hold
?
To
change to the desired program, whilst in
child
?
lock mode.
1. Press and hold both
Option
and Rinse button
together once again.
2. Press the Start/Pause button.
3. Select the desired program and press the
Start/Pause button again.
?
Is selected by pressing the Rinse button
repeatedly this function leaves clothes in the
washer; suspended in the water after a rinse
without entering into spin.
To
proceed through
to a drain or
program dial scroll to
The
required lamp
identification.
?
The child lock
can
be set at any time and it is
automatically canceled when operational
occur.
18
errors
Also Child lock works when power is off.
spin, once
completed using to
the required program.
the rinse hold function is
will
light up for
H
to
ow
use
Time
washer
Spin
Delay
?
2
By pressing the
Spin button, the
spin speed can
be chosen.
1. Time
Delay
Preparing washing before starting
Turn on the water tap.
"Time
Delay"
[WD-14311RD/
WD-14316RD]
Spin only
-
-
-
?
laundry and close the door.
Place the detergent and fabric softener
1. Press the Power button.
Load
2. Set the desired
in
spin speed by pressing
the drawer.
button.
3. Press the Start/Pause button.
How to set "Time
1. Spin selection
-
-
-
Delay"
Power( ) button.
Turn the Program dial to select
the program you require.
Press Time Delay button and set the
-
the
spin
Press
desired time.
Press the
If Time
Delay
displayed.
?
button is
)
?
button.
-
The maximum
is available
according
to the program
follows.
WD-14311RD/WD-14316RD
Cotton & Cotton-Eco & Quick 30
No
-
pressed, "3:00" is
delayed time is
Spin speed
as
-
Start/Pause(
lamp is on)
"
("
?
[WD-12311RD/
WD-12316RD]
Spin-400-800-1000-1400
Synthetic & Wool/Silk
No Spin-400-800-1000
& Hand Wash & Duvet
Delicate
No
Spin-400-800
19:00 hours and the minimum time is 3:00
?
hours.
-
?
Each pressing of the button advances time
delay by one hour.
No
-
?
To cancel the time
Power(
?
Time
?
is
-
Spin-400-800-1000-1200
Synthetic & Wool/Silk
No Spin-400-800-1000
& Hand Wash & Duvet
Delicate
No
time' from the
'expected
completion of washing cycle
process (Wash, Rinse, Spin).
Delay
present
or
delay, press the
button.
)
WD-12311RD/WD-12316RD
Cotton & Cotton-Eco & Quick 30
Spin-400-800
to the
selected
According to
the condition
of water supply and
temperature, the delayed time and the actual
washing time
may vary.
2. No spin
?
If "No
after
The
Spin" is selected,
draining water.
required lamp
identification.
will
the washer stops
light up for
19
H
ow
to
washer
use
Water Temp.
?
Dry
By pressing the Temp.
?
button, the water
temperature can be
washer-dryer's
automatical
process from washing to
can be selected easily.
selected.
-
This
?
Cold
-30˚C/40˚C/60˚C/95˚C
For most
even
drying
,
drying
make
sure
all articles in the clothes
load
are
similar in material and
thickness.
?
1. Water Temperature
?
-
Water temperature can be selected
according to the program.
as
below
If you open door and
dryer has finished its
Cotton
Synthetic
Low
Cold-30˚C-40˚C-60˚C
Delicate & Wool/Silk & Quick 30 &
will
more
detailed
"
Cooling Cycle.
1.Drying
Intensive
?
Automatic
?
?
If the
laundry is heavily soiled "Intenive"
option is effective.
By selecting the Intensive option, the wash
time may be extended, depending on the
program selected.
To use this option press the Intensive button
once before the wash program is started.
or
decrease
drying
temperatures for faster reaction time and tighter
temperature control.
?
Recommand Automatic
drying
course as a
kind
of clothes.
a) Synthetic Low Temp.
b) If you want to iron clothes-Iron.
c) Cotton Cupboard.
d) Diaper Very
NOTE: The estimated drying time varies
from the actual drying time with an Automatic.
-
-
-
The
20
guide
Use your Automatic Cycles to dry most loads.
Electronic sensors measures the temperature of
the exhaust to increase
Intensive
?
"
ended after about 4 hours.
information, please refer to
the page13.
Iron
Temp.
program can be ended. If you not press
the "Start/Pause" button, the program is
light up for
"
For the
select
Time
Very
"
Hand Wash & Duvet
required temperature lamp
identification.
can
After the end of dry,
is displayed.
By pressing the "Start/Pause" button the
?
Cold-30˚C-40˚C
The
load before
remember to
the DRY button, you
By pressing
Cupboard
Cold-30˚C-40˚C-60˚C-95˚C
-
remove
cycle,
press the Start/Pause button.
Cotton-Eco
40˚C-60˚C
-
dryer by stuffing
freely
?
?
-
Do not overload
too many articles into drum.
Items must be able to tumble
type of fabric, size of the load, and
dryness selected affect drying time.
the
H
ow
2.Drying
?
By
to
time
use
washer
guide
press the Dry button, the
be selected.
Fiber
drying
time
dry fiberglass articles in your dryer.
particles left in the dryer could be
picked up by your clothes the next time
you use the dryer and irri tate your skin.
Glass
can
?
Drying
course can
last up to 100min.
When
?
selecting drying only, drying course
will start after spining.
These drying times are given as a guide to
help you set your dryer for manual drying.
Drying times can vary greatly depending on
dampness, room temperature and type of
fabric and your own experience will be your
best guide.
Woolen Articles
-
-
Some
Loopknit
-
Always
drying.
immediately
Do not overload your
Always
Always
or
drying cycle is completed,
[Cool Down] is displayed on the Multi
display.
The Cool Down is setting automatically
when a drying cycle is complete.
"
When you are not remove a loaf of clothes
from the dryer as soon as it stops, wrinkles
form.
The Cool Down
operating periodically
tumbles, rearranges and fluffs the load to
avoid wrinkles without heat for up to 4
hours.
?
message will continue to
until the clothes are removed or the
The
Start/Pause button is
display
pressed.
Synthetics
dryer
Take out permanent press articles as
as the dryer stops to reduce wrinkles.
soon
Leather Materials
check the manufacture's instructions.
Baby
-
after
"
When
can
?
and
stretch them out
Fiber
-
?
Materials
loopknit materials may
shrinks, by varying amounts, depending on
their quality.
woven
Permanent Press and
-
?
?
dry woolen articles. Pull them
original shape and dry them flat.
Woven and
-
3.Completion of Drying
Do not tumble
to their
glass
Do not
-
clothes and
Night
Gowns
check the manufacture's instructions.
Rubber and Plastics
-
Do not dry any items mode from or
containing rubber or plastics, such as:
a) aprons, bibs, chair covers
b) curtains and table cloths
c) bathmats
21
ow
H
to
washer
use
Display
3. Completion of
?
When
washing cycle is completed,
is displayed on the "Multi
display".
"
1. Special function
display
"
"
?
After the end of
?
dry,
"
"
is
displayed.
delay is selected, it shows
remaining times to finish the selected
When time
?
the
?
During washing cycle, the remaining
washing time is displayed.
Recommended program
-
program.
-
2. Self
diagnose display
-
-
?
"
4. Time left
When Child lock is selected, the
lamp is on.
?
washing
If the washer encounters
operation,
displayed.
a
fault
during
-
the associated fault will be
-
-
"
"
Water pressure
:
sensing
error
-
"
"
"
"
Problem of
:
overfilling
water
-
"
"
"
"
:
Door is not closed
:
Over load in motor
:
Over load in motor
:
Water inlet trouble
:
Drainage
:
Unbalanced load
?
"
"
"
"
"
"
"
"
"
"
?
Water temperature trouble
:
The water
:
Dry
experienced
a
power
heater
or
thermostat
trouble.
If these error letters are displayed, please
refer to the troubleshooting page26 and
follow the guide.
22
Cotton : around 1 hour and 50 minutes
Cotton-Eco : around 2 hours
Synthetic : around
1 hour and 15 minutes
Delicate : around 1 hour 5 minutes
Wool/Silk : around 55 minutes
Hand Wash : around 50 minutes
Quick 30 : around 30 minutes
Duvet : around 1 hour
Drain: around 1 minute
The
washing time may vary by the
laundry, water pressure, water
temperature and other washing conditions.
trouble
:
"
manufacturer.
amount of
failure.
"
by
If
an
unbalanced load is detected
or
if the
suds
removing program operates, the
wash time may be extended.
(Max. increasing
time is 45
minutes.)
aintenance
M
Before
cleaning the washer interior, unplug
the electrical power cord to avoid electrical shock to
avoid electrical shock hazards.
When
disposing
of the
appliance, cut off the mains cable,
being trapped inside.
and
destroy the plug
Disable the door
lock to prevent young children
The water inlet filter
"
-"
message will blink
error
detergent
If your water is very hard
-
on
the control
panel
when water does not enter the
drawer.
or
contains traces of lime
deposit,
the water inlet filter may
become
It
clogged.
is therefore a good
idea to clean it from time to time.
2. Unscrew the
1. Turn off the
water
water inlet
tap.
hose.
3. Clean the
filter
4.
using
Tighten
up
the inlet
a
hard bristle
hose.
brush.
The drain pump filter
The drain filter collects threads and small
Check
!
regularly that the filter
CAUTION
First drain
is clean to
using
objects
ensure
left in the
smooth
laundry.
running of your
machine.
the drain hose and then open the pump filter to
whatever any threads
or
remove
objects.
draining if the water is hot.
down before cleaning the drain pump, carrying
Be careful when
Allow the water to cool
emptying
1.
or
opening
Open the lower cover
cap ( ) by using a
coin. Drain plug ( )
to pull out the hose.
the door in
2.
an
Unplug the drain plug ( ),
allowing the water to flow out.
this time
water
use a
flowing
3. Remove out any
At
vessel to prevent
on
to the floor. When
cleaning,
material
After
( )
clockwise and insert the drain
)to
the
plug (
close the lower
( )
( ).
turn the pump filter
the pump filter
open to the left.
foreign
from the pump filter
water does not flow any more, turn
original place.
cover
cap.
2
100
1
out emergency
emergency.
2
3
3
23
aintenance
M
Dispenser drawer
After
?
?
a
while
and fabric softeners leave
detergents
a
deposit
in the drawer.
It should be cleaned from time to time with
If necessary it
can
be removed
a jet of running water.
completely from the machine by pressing
by pulling it out.
cleaning, the upper part
the catch
downward and
?
To facilitate
The drawer
Detergent
can
be cleaned
?
cycle
The
?
also accumulate inside the
seen
with
occasionally
without
washing
If you live in
a
can
be removed.
recess
Once you have finished
rinse
of the fabric softener compartment
recess
old toothbrush.
an
cleaning, replace
the drawer and
run a
laundry.
drum
hard water area, limescale may
and thus not
which should
easily
continuously
build up in
places where
it cannot be
removed.
Over time the build up of scale
clogs appliances,
and if it is not
kept
in check these may have to be
replaced.
?
?
?
Although the washing drum is made of Stainless steel, specks of rust can
articles (paper clips, safety pins) which have been left in the drum.
The
washing
If you
use
be caused
descaling agents, dyes
or
bleaches, make
Descaler may contain chemicals that may
Remove any spots with
24
use
small metal
drum should be cleaned from time to time.
sure
they
are
suitable for
washing
use.
Never
by
steel wool.
a
stainless steel
damage part of your washing
cleaning agent.
machine.
machine
aintenance
M
The water circulation nozzle
?
Clean the water circulation nozzle, if
Cleaning
clogged.
your washer
1. Exterior
of your washer
can
extend its life.
The outside of the machine
can
be cleaned with
Proper
care
household
detergent.
Immediately wipe off any spills. Wipe
Try
water and a neutral non abrasive
warm
not to hit surface with
IMPORTANT: Do not
with
damp cloth.
sharp objects.
methylated spirits, diluents
use
or
similar
products.
2. Interior
Dry around the washer door opening, flexible gasket and door glass.
Run washer through a complete cycle using hot water.
Repeat process if necessary.
NOTE
Remove hard water
machine.
Winterizing
deposits using only cleaners labeled
an area
where
freezing
may
temperatures, follow these instructions to prevent
1. Turn off water
4. Add
washing
occur or
damage
moved in
freezing
to the washer:
supply tap.
2. Disconnect hoses from water
Plug
safe for
instructions
If the washer is stored in
3.
as
electrical cord into
1gallon(3.8L)
a
supply and drain
water from hoses.
properly grounded electrical outlet.
of nontoxic recreational
vehicle(RV) antifreeze
into
an
empty wash drum.
Close the door.
5. Set
spin cycle and let washer spin for 1minute
Not all of the RV antifreeze will be
6.
Unplug
electrical power cord,
7. Remove
dispenser
8. Store washer in
9. To
remove
through
a
an
dry
to drain out all water.
expelled.
the drum interior, and close the door.
drawer, drain and
dry excessive
water from the
compartments.
upright position.
antifreeze from washer after storage,
complete cycle using detergent. Do
run
empty washer
not add wash load.
25
T roubleshooting guide
This
washing machine is equipped with automatic safety functions which detect and
diagnose faults at an early stage and react appropriately.
When the machine does not function properly or does not function at all, check the
following points before you contact your service provider.
Possible Cause
Symptom
Rattling and
clanking noise
?
Solution
Foreign objects such as coins
safety pins maybe in drum or
or
Stop
washer and check drum
and drain filter.
If noise continues after washer
pump.
is restarted, call your authorized
service centre.
Thumping
sound
?
Heavy wash loads
thumping sound.
a
may produce
This is usually
normal.
Vibrating
noise
?
?
If not removed
been removed?
Are all the feet
the
out of balance.
Stop
and
redistribute wash load.
Have all the transit bolts and
packing
If sound continues, washer is
probably
during
installation, refer to Installation guide
resting firmly
on
for
removing
transit bolts.
Wash load may be
distributed
ground?
in drum.
Stop
unevenly
washer and
rearrange wash load.
Water leaks.
?
Fill hoses
at
?
tap
or
or
drain hose
are
loose
Check and
tighten
hose connections.
washer.
House drain
pipes
are
clogged.
Unclog
drain
pipe. Contact plumber
if necessary.
Too much
Oversudsing
detergent
detergent may
foaming which
or
cause
unsuitable
excessive
may result in water
leaks.
Water does not enter
washer
or
?
it enters
slowly
Water
supply
is not
adequate
in
Check another tap in the house.
area.
?
?
?
Water
supply tap
completely open.
Water inlet
is not
hose(s)
are
The filter of the inlet
Fully
kinked.
hose(s)
are
open tap.
Straighten hose(s).
Check the filter of the inlet
clogged.
Water in the washer
does not drain
?
?
drains
26
slowly.
Drain hose is kinked
or
clogged.
or
The drain filter is
clogged.
Clean and
straighten
Clean the drain filter.
hose(s).
the drain hose.
T roubleshooting guide
Possible Cause
Symptom
Washer does not start
?
Electrical power cord may not
plugged in or connection
be
Solution
Make
plug fits tightly
sure
in wall
outlet.
may be loose.
?
House fuse blown, circuit
Reset circuit breaker
breaker
Do not increase fuse
tripped,or
a
power
outage has occurred.
If
problem
is
a
replace
capacity.
or
fuse.
circuit overload, have
it corrected
?
Water
supply tap
is not turned
by a qualified electrician.
on water supply tap.
Turn
on.
Washer won't
Check that the door is
spin
shut.
firmly
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the clothes
washer
begins to spin. The door
spin can be
must lock before
achieved.
Once started, the door can not be
for safety reasons.
Door does not open
opened
Wait
one or
two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash
cycle
delayed
time
The
washing time may vary by the
laundry, water
amount of
pressure, water temperature and
other using conditions.
If the imbalance is detected
suds
or
if the
removing program works, the
wash time shall be increased.
Dry problem
?
Does not
dry
Do not overload.
Check that the washer is
properly to
extract
draining
adequate water
from the load.
Clothes load is too small to tumble
property. Add
a
few towels.
27
T roubleshooting guide
Possible Cause
Symptom
?
?
?
?
Water
Water
supply is not adequate in area
supply taps are not completely
open.
Water inlet
hose(s)
are
The filter of the inlet
kinked.
hose(s)
are
Solution
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
clogged.
?
?
?
?
?
Drain hose is kinked
Clean and
The drain filter is
Clean the drain filter.
or clogged.
clogged.
straighten the drain
Load is too small.
Add 1
Load is out of balance.
balance the load.
The
Rearrange
spinning
appliance
has
unbalance
an
detection and correction system. If
individual heavy articles are loaded
or
2 similar items to
hose.
help
load to allow proper
(ex.
etc.), this system
may stop spinning or even interrupt the
spin cycle altogether.
If the laundry is still too wet at the end
of the cycle, add smaller articles of
laundry to balance the load and repeat
the spin cycle.
bath mat, both robe,
?
?
Is the door
or
not
opend
completely
Close the door
If
"
completely.
"is not released, call for service.
closed?
Unplug the
?
Water overfills due to the
faulty water
valve.
power
plug
and call for service.
Close the water tap.
Unplug the power plug.
Call for service.
?
?
?
?
28
Water level
sensor
has malfunctioned.
Over load in motor.
Over load in motor.
Check water
supply.
Turn the tap on
If"
is not released,
plug and call service.
"
unplug
power
T
erms
of Warranty
What Is Not Covered:
?
?
?
?
Service
trips
to your home to teach you how to
If the
product
rating plate.
is connected to any
voltage
If the fault is caused
by accident, neglect,
If the fault is caused
by factors
use
the
product.
other than that shown
misuse
or
on
the
Act of God.
other than normal domestic
use or use
in
accordance with the owner's manual.
?
?
?
Provide instruction
If the fault is caused
Noise
or
of
product
change
or
by pests for example,
Correcting
or
the set-up of the
product.
rats or cockroaches etc..
vibration that is considered normal for
sound, spin sound,
?
on use
example
water drain
warming beeps.
the installation for
example, levelling
the
product, adjustment of
drain.
?
?
Normal maintenance which recommended
Removal of
foreign objects
?
?
?
Replace fuses
Incidental
example, grit, nails,
in or correct house
Correction of unauthorized
the owner's manual.
/ substances from the machine,
pump and inlet hose filter for
?
by
wiring
or
correct house
or
product
the
plumbing.
repairs.
consequential damage to personal property
possible defects with this appliance.
If this
including
bra wires, buttons etc.
caused
by
is used for commercial purpose, it is not warranted.
(Example : Public places
center, dormitory)
such
as
public bathroom, lodging house, training
If the
product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement of
defective part, shall be borne by the owner.
29
a
M
30
emo
For U.K. Customer
CUSTOMER SERVICES
:
0870-592-9929(Service Force)
Mon.-Fri. 8:30AM
LGEUK SERVICE WEB-SITE
:
-
5:30PM
www.lgelectronics.co.uk
Download PDF