LG | WD-1370FHB | LG WD-1370FHB Owner’s Manual

Washing
Machine
OWNER'S MANUAL
WM-1370(5)FHB
WM-1270(5)FHB
WM-1170(5)FHB
WM-1070(5)FHB
WM-8070FHB
Thank you for buying a
LG Fully Automatic Washing machine.
Please read your owner's manual carefully, it provides
on safe installation, use and maintenance.
instructions
Retain it for future reference.
Record the model and serial numbers of your
washing
machine.
P
roduct Feature
40%
∀
Jumbo drum
LG's
jumbo
drum
conventional
can
wash about 40%
machines. A
washing
more
bigger
load than
drum
improves
the wash
performance.
∀
More economical
Intelligent
Wash
by Intelligent
System
Wash
System
detects the amount of load and water
temperature, and then determines the optimum
time to minimize energy and water
washing
∀
Child-Lock
The Child-Lock
pressing
∀
system has been used
any button to
Low noise
speed
change
control
to
prevent children from
the program
during operation.
system
the amount of load and balance, it
load to minimize the spinning noise level.
By sensing
∀
water level and
consumption.
evenly
distributes
Auto Restart
If the washing machine is turned off by a power failure, it will restart
automatically from the position it stopped at adjusting accordingly.
C
ontents
Warnings....................................................................................3
Specification
..............................................................................4
Installation..................................................................................5
Care before
washing................................................................11
Adding detergent
.....................................................................12
Function ...................................................................................13
How to
use
washer ..................................................................14
Maintenance ............................................................................21
Troubleshooting guide
2
.............................................................24
arnings
W
RE
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
WARNING!
!
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock,
the
?
Do not install
be
?
?
or
store the washer where it will
?
exposed to the weather.
Do not
tamper with controls.
repair or replace any part of the washer
attempt any servicing unless specifically
instructions
or
published user-repair
instructions
?
that you understand and have the skills to carry
Keep the area underneath and around your
appliances free of combustible materials such
lint, paper, rags, chemicals, etc.
Close supervision is necessary if this
is used
by
or near
Do not wash
or
dry
articles that have been
or spotted with
explosive substances (such as
wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may
ignite or explode.
To avoid such a result, carefully follow the
garment manufacturer's wash and care
in, washed in, soaked in,
or
on,
with,
this or any other
Do not leave the washer door open.
An open door could entice children to
or
appliance
or
?
inside
?
Never reach into washer while it is
?
The
hang
can
try to
To minimize the
this
possibility of electric shock,
appliance from the power supply
or
disconnect the washer at the household
on
?
moving.
completely stopped.
laundry process
retardant of fabrics.
or
distribution
crawl inside the washer.
until the drum has
Do not slam the washer door closed
force the door open when locked. This could
result in damage to the washer.
as
unplug
play
appliance.
the door
?
children.
Do not allow children to
?
using
instructions.
out.
?
to persons when
combustible
recommended in the user-maintenance
?
injury
cleaned
Do not
or
or
washer, follow basic precautions, including the following:
Wait
reduce the flame
panel by removing the fuse or
switching off the circuit breaker before
attempting any maintenance or cleaning.
Never attempt to operate this appliance if it is
damaged, malfunctioning, partially
disassembled, or has missing or broken parts,
including a damaged cord or plug.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This
grounded. In the event of malfunction or breakdown, grounding will reduce the risk
by providing a path of least resistance for electric current. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
Do not use an adapter or otherwise defeat the grounding plug.
appliance
must be
of electric shock
?
?
If you don't have the proper
WARNING :
outlet, consult
an
electrician.
Improper
connection of the equipment-grounding conductor can result in risk of electric
qualified electrician or serviceman if you are in doubt as to whether the appliance is
properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a
proper outlet installed by a qualified electrician.
shock. Check with
a
-
3
pecification
S
Power
If the
plug
supply cord is damaged,
replaced by the
it must be
manufacturer
or its service agents
similarly qualified person in
Drawer
or a
(For detergent and
fabric softener)
order to avoid
Control
a
hazard.
panel
Drain hose
Door
Lower
cover
Drum
Leveling leg
Drain pump filter
Lower
Drain
cap
plug
∀
Name
∀
Power
supply
:
Front
:
220-240V~,50Hz
600mm(W)
63kg
7.0kg
∀
Size
:
∀
Weight
Wash capacity
:
∀
Max. Watt
:
∀
Spin speed
:
∀
cover
:
loading washing
machine
600mm(D)
850mm(H)
2100W
No
Spin/400/600/800[WM-8070FHB]
Spin/400/600/800/1000[WM-1070(5)FHB]
No Spin/400/600/800/1100[WM-1170(5)FHB]
No Spin/400/600/800/1000/1200[WM-1270(5)FHB]
No Spin/400/600/800/1100/1300[WM-1370(5)FHB]
:75
(10.7 /kg)
: 0.3-10kgf/
(30-1000kPa)
No
∀
Water
∀
Permissible water pressure
consumption
The appearance and
∀
specifications
Accessories
Hot/Cold(2EA)
4
may be varied without notice to raise the units
Spanner
quality.
nstallation
I
or store where it will not be exposed to temperatures below freezing or exposed to the weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
Install
Transit bolts
∀
The
∀
appliance
is fitted with transit bolts to
Removing
prevent internal damage during transport.
transit bolts
1. To
prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts
along
with the rubber
3. Take out the 4 bolts
along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for future
?
?
If
they
are
not
removed, it may
use.
bungs.
cause
heavy
Whenever the
appliance
is
transported,
the
transit bolts must be refitted.
vibration, noise and malfunction.
cap
2. Unscrew the 4 bolts with
the spanner
4. Close the holes with the caps
supplied.
supplied.
5
nstallation
I
∀
Installation
place requirement
Level floor
Drain Hose
Allowable
Washer
:
under entire washer is 1˚
slope
Power outlet
:
Must be within 1.5 meters of either side of location
of washer. Do not overload the outlet with
than
Laundry
one
Additional Clearance :
For wall, door and floor modeling is
Tub
approx.
2cm
more
appliance.
(10cm
: rear
Do not
place
/2cm:right
or
store
& left
required.
side)
laundry products
washer at any times.
They can damage the finish
or
on
top of
controls.
650
850
600
∀
BS
Plug Safety Details (For
U.K.
User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This
appliance
Green and Yellow(Earth)
must be earthed
E
Brown(Live)
L
Blue(Neutral)
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the
identifying
letter E
or
by
the earth
symbol (
)
or
coloured Green
or
Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N
or
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L
If
a
13 amp
6
(BS 1363) plug
is
used, fit
a
13 amp BS 1362 fuse.
coloured Black.
or
coloured Red.
nstallation
I
∀
Electrical connection
1. Do not
use an extension cord or double adapter.
supply cord is damaged, it must be replaced by the
or similarly qualified person in order to avoid a hazard.
Always unplug the machine and turn off the water supply
2. If the
3.
4. Connect the machine to
5. The
∀
appliance
Washing
must be
an
manufacturer
after
so
that the
plug
is
easily
its service
agents
use.
earthed socket in accordance with current
positioned
or
wiring regulations.
accessible.
Machine is to be connected to the water mains
using
new
hose-
sets and that old hose-sets should not be used.
∀
Connecting
water
hose
supply
Water
supply pressure must be between
(0.3~10kg.f/cm2)
30kPa and 1000kPa
Don't
strip or crossthread when connecting
Inlet hose to the valve.
If the water supply pressure is more than
1000kPa, a decompression device should be
installed.
?
Two rubber seals
are
supplied with
the
water inlet hoses these are in order to
prevent
Hose connector
?
Rubber seal
water leaks.
Check water tightness of washing
machine connections by turning the
completely
?
tap
on.
Periodically check the condition of the
replace the hose if necessary.
hose and
?
Hot water
?
Hot(option)
on
the
When your washer has two valves,
tap
Cold
Cold
Make sure that there is no kink
hose and that it is not crushed.
water
tap
?
The Inlet hose which has red connector is
for the hot water tap.
If the washer has two valves, the energy
is saved by using hot valve.
7
nstallation
I
Tap without
∀ Normal
1. Unscrew the fixing
attach the tap.
screw
thread &
2.
to
screw
type inlet hose
Push the connector up till the
rubber
packing
with the
3.
is in
tap. Then
tight contact
tighten the 4
screws.
Tap without
∀ Normal
1. Untighten the upper
thread &
connector
2.
touch
one
packing
contact with the
Upper
Rubber
Connector
Fixing
tighten
packing
screw
type inlet hose
Push the upper connector up till
the rubber
screw.
Middle
the 4
Rubber
connector
Push the water supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
is in
3.
Connect the water
to the middle
tight
tap. Then
pushing
the
supply
hose
connector,
plate
down.
screws.
Upper
Connector
packing
Plate
Upper
?
In
case
large
the diameter of the
remove
Guide
the
tap is
Connector
Water
hose
Middle
guide plate.
connector
plate
Turn the middle connector not
?
to have water leaked.
Connector
?
Make
sure
that the rubber seal
is inside the hose connector.
?
To
supply
separate the
water
supply
hose from the middle connector
shut off the
inlet hose
plate
tap. Then pull the
down, pushing the
down.
Hose connector
Rubber seal
Used the horizontal
Horizontal
tap
tap
?
Your machine
comes
with
only
cold water connection.
?
Extension
tap
Make
sure
that there
not crushed.
Square tap
8
are no
kinks in the hose and that it is
I
∀
nstallation
Installation of drain hose
ca.
ca.
145
100
cm
cm
?
max.10cm min.60cm
ca.
105
When
installing the drain hose sink,
it tightly with a string.
secure
cm
?
Proper securing the drain hose will protect
damage due to water
leakage.
the floor from
Laundry tub
ca.
100
cm
Hose
ca.
145
Retainer
cm
Tie
max.
ca.
?
than 100
Proper securing
protect
water
?
cm
placed
?
above the floor.
the drain hose will
the floor from
damage
due to
leakage.
When the drain hose is too
100cm
min. 60cm
strap
min. 60cm
min.60cm max.10cm
cm
The drain hose should not be
higher
?
105
100cm
max.
When
installing the drain hose sink,
it tightly with a string.
secure
?
Proper securing the drain hose will protect
damage due to water
leakage.
the floor from
long, please
don't fill into the washer. This will
cause
abnormal noise.
9
I
∀
nstallation
Level
adjustment
1.
Leveling
the
prevents
excessive noise and vibration.
Install the
floor
the
washing
appliance
machine
on a
properly
solid and level
surface, preferably in
a corner
of
room.
2. If the floor is uneven, adjust the leveling
feet as required. (do not insert pieces of
wood etc. under the
Make
sure
feet)
that all four feet
are
stable
and
resting on the floor and then check
that the appliance is perfectly level. (use
a spirit level)
Leveling leg
Higher
Lower
Leveling leg
Diagonal Check
When pushing down the edges of the
washing machine top plate diagonally,
machine should not
move
the
up and down at
(Please, check both of two directions)
If machine rocks when pushing the machine
top plate diagonally, adjust the legs again.
all.
10
C
∀
before
are
Caring
before
washing
washing
1. Care Labels
Look for
garment
2.
label on your clothes. This will tell you about the fabric content of your
and how it should be washed.
a care
Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle.
Water temperature and spin speed and different fabrics need to be washed in different ways.
Always
transfer
sort dark colors from
soiled items with
Soil
3.
Caring
∀
before
colors and whites. Wash
separately as dye and lint
possible, do not wash heavily
one.
(Heavy, Normal, Light)
(White, Lights, Darks)
(Lint producers, Collectors)
Color
Lint
pale
discoloration of white etc. If
causing
lightly soiled
can occur
Separate clothes according to amount of soil.
Separate white fabrics from colored fabrics.
Wash lint producers and lint collectors
separately.
loading
Combine large and small items in a load. Load large items first. Large items should not be more
than half the total wash load.
Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.
?
Check all the
that
as
pockets
to make sure
empty. Things such
nails, hair clip, matches, pens,
they
are
coins and
keys
can
damage
both
your washer and your clothes.
?
Close
zippers,
make
sure
snag
?
on
hook and
little
to
other clothes.
Pre treat dirt and stains
a
strings
that these items don't
detergent
by brushing
dissolved in water
onto stains like collars and cuffs to
help
shift dirt.
11
dding detergent
A
∀
Adding detergent
1. The
Dispenser
and fabric softener
3. Detergent dosage
Drawer
?
The
detergent should be used according to
of the detergent manufacture.
the
instruction
max
?
If too
much
detergent is
used more than the
recommended amount, too many suds can
occur and this will decrease the washing result
heavy load to the
malfunction)
or cause
?
Use powder
loading
?
Main wash
only
U
?
(Causing
a
detergent only for the front
washer.
Detergent
for water
?PreWash+MainWashU
motor.
usage may need to be
temperature,
water
adjusted
hardness,
size and soil level of the load. For best
2.
results, avoid oversudsing.
Adding Fabric Softener
(
)
MAX
MAX
125 ml
125ml
Tips
Full load
Part load
?
Do not exceed the maximum fill line.
Overfilling
can cause
clothes.
Do not leave the fabric softener in the
Softener will
during
?
automatically
cycle.
2
days.
be added
last rinse
Do not open the drawer when water is
supplied.
?
Solvents(benzene, etc)
are
not
allowable.
NOTE
Do not pour fabric softener
on the clothes
directly
12
:
3/4 of the normal amount.
Minimum load
?
:
1/2 of full load.
Detergent is flushed from the dispenser
beginning of the cycle.
the
detergent drawer for more than
(Fabric softener could harden)
?
to
early dispensing
of the fabric softener which could stain
?
according
:
manufacturer's recommendation.
at
unction
F
∀ Recommended
courses
Fabric
according
Temp.
First check if
Whites
laundry is machine
washable.
(white cotton, linen
towel and
Eco
(60˚C, 50˚C,
Rinse+
40˚C)
Bio
sheets...)
(shirts, night dresses,
Delicate
Delicate laundry
easily damaged
(silk, curtains...)
Wool
Machine washable
woolens with pure
new wool only
Hand
"Hand Wash"
Wash
marked delicate and
wool
Pre Wash
You
in
in
Load
Liter
kWh
Minutes
Rating
85
2.74
158
Rating
75
0.72
115
Less than
58
0.6
88
58
0.41
58
53
0.28
58
51
0.03
57
Pre Wash
40˚C
:
laundry
40˚C
(50˚C, 60˚C,
Cold, 30˚C)
Eco
Rinse+
Bio
Rapid
Pre Wash
Eco
Rinse+
Less than
Rinse+
30˚C
(40˚C, Cold)
Cold(30˚C,
40˚C)
kg
Bio
30˚C
(40˚C, Cold)
4.0
3.0
kg
Less than
Rinse+
Rinse+
2.0
kg
Less than
2.0
kg
If the
laundry is heavily soiled, "Pre Wash" course is effective. Pre Wash is available in
Coloureds, Whites and Synthetic Program.
By selecting Eco function, the water temperature is reduced and washing
lengthened. So you can economize in your consumption of energy.
Rinse+
:
Energy
in
Rapid
pajamas...)and
(50˚C, 60˚C,
lightly soiled white Cold, 30˚C)
cotton(underwear...)
Synthetic Polyamide, Acryic,
Polyester
:
If you wish to rinse more, the Rinse+ function will
If you want to elimenate protein stains
by pressing the option button.
can
Time
Water
Pre Wash
95˚C
Coloureds Color fast gaments
Bio
Maximum
Option
Type
:
laundry type
Proper
Program
Eco
to the
any trace of
detergents.
(milk, blood, chocolate...), you may select Bio function
select Bio function and Eco function when
Coloureds and
remove
time is
temperature is higher than 60˚C in Whites,
Synthetic.
13
H
ow to use
1. For
use
washer
in the initial
programme
2. Manual
?
Push the Power button to start.
?
?
Push the Start/Pause button.
?
?
Initial condition
-
Wash
:
Only main
-
Rinse
:
3 times
wash
-
Water temperature
:
40˚C
Program : Coloureds
14
Push the Power button to start.
Select the conditions which you want to
use, by pressing each button.
For selecting the each
conditions, please
refer to the page15~page20
?
-Spin:800rpm
-
Selecting
(Coloureds)
Push the Start/Pause button.
H
ow to use
(1)
(1)
(2)
(3)
Button
:
Button
:
Button
:
washer
(2)
(3)
(4)
(5)
(6)
By pressing the Option
button, the Option function
can
-
Rinse+
-
Eco
-
Pre Wash
Button
Dial
:
:
Start/Pause
Program
Button
:
Power
By selecting Eco function, the water
temperature is reduced and washing time is
lengthened. So you can economize in your
consumption of energy.
[You can select Eco function when
temperature is higher than 60 C in Whites,
Coloureds and Synthetic.]
4. Pre Wash
1. Bio
?
?
be selected.
Bio
(7)
(8)
(9)
(9)
3. Eco
Option
-
(8)
(4) Child lock
(5) Button : Time Delay
(6) Button : Rapid
Option
Spin
Temp.
?
(7)
If you want to elimenate protein stains(milk, blood,
chocolate...), you may select Bio function by
pressing the option button.
[You can select Bio function when temperature
higher than 60 C in Whites, Coloureds and
Synthetic.]
?
?
is
If the
laundry
course
is
heavily soiled,
Pre Wash is available in
Coloureds and
If lamp
"Pre Wash"
is effective.
turns on,
Whites,
Synthetic.
that function has been
selected.
2. Rinse+
?
?
If you wish to rinse more, Rinse+ function
will remove any trace of detergents.
By selecting Rinse+ function,
Time and the Rinse water
are
the Rinse
increased.
15
ow to use
H
washer
Spin
?
WM-1070(5)FHB
-
Whites /
Coloureds/Synthetic
800U 1000U Rinse HoldU No
SpinU
-
400U 600
Delicate
400U 600U 800U Rinse HoldU No
-
Spin
Wool / Hand Wash
400U 600U 800U 1000U Rinse HoldU No
[WM-8070FHB]
[WM-1070(5)FHB]
Spin
[WM-1170(5)FHB]
?
WM-1170(5)FHB
-
Whites /
Coloureds/Synthetic
800U 1100U Rinse HoldU No
SpinU
-
400U 600
Delicate
400U 600U 800U Rinse HoldU No
-
Spin
Wool / Hand Wash
400U 600U 800U 1100U Rinse HoldU No
Spin
[WM-1270(5)FHB]
?
By pushing
can
[WM-1370(5)FHB]
the
Spin button,
?
the
spin
rpm
WM-1270(5)FHB
-
be chosen.
Whites / Coloureds
800U 1000U 1200U Rinse HoldU
No
1.
?
Spin selection
Spin speed
program
as
is available
-
according
-
16
SpinU
Delicate
400U 600U 800U Rinse HoldU No
Whites / Coloureds / Synthetic
800U Rinse HoldU No SpinU 400U 600
Delicate / Wool / Hand Wash
400U 600U 800U Rinse HoldU No
Synthetic
400U 600
follows.
WM-8070FHB
-
400U 600
800U 1000U Rinse HoldU No
to the
-
?
SpinU
Spin
-
Spin
Wool / Hand Wash
400U 600U 800U 1000U Rinse HoldU No
Spin
ow to use
H
washer
Water
?
Temp.
WM-1370(5)FHB
-
No
SpinU 400U
Synthetic
600
SpinU
Cold
-30˚C/40˚C/50˚C/60˚C/
95˚C
400U 600
Delicate
400U 600U 800U Rinse HoldU No
-
Temp
selected.
-
800U 1100U Rinse HoldU No
-
the
button, the water
temperature can be
800U 1100U 1300U Rinse HoldU
-
By pushing
?
Whites / Coloureds
Spin
Wool / Hand Wash
400U 600U 800U 1100U Rinse HoldU No
Spin
1. Water
?
2. No
spin
If
spin is selected,
draining water.
no
If lamp
turns on,
the washer
stops after
-
that function has been
-
3. Rinse Hold
?
according
Whites
95˚C U 40˚C
Coloureds &
40˚CU
selected.
?
temperature
below
-
?
Water
-
U
Selected
getting wrinkled, you may select rinse
For the
hold
by pressing
button.
be selected
as
50˚C
U
60˚C
Synthetic
50˚CU
60˚CU
ColdU
30˚C
Hand Wash
Cold
from
spin
U
can
to the program.
Delicate & Wool
30˚C U 40˚C U Cold
If you desire to leave fabrics in the machine
without spinning after rinse to prevent them
the
Temperature
30˚C
U
40˚C
temperature's lamp
more
detailed
turns
on.
information, please refer
to the page13.
If you want to drain and spin, when Rinse
Hold function is proceed, Push the
Start/Pause button to cancel the Rinse Hold
function and select
spin speed or program.
again to start
Push the Start/Pause button
program.
?
If you want to drain
or
only,
select the
no
spin
pump program.
If lamp
turns on,
that function has been selected.
17
H
ow to use
washer
Child lock
Time
Delay
Time Left
If you want to lock all the buttons to prevent
a child or infirm persons, this
operation by
function
can
be used.
Time Left
1. Time
Delay
Preparing washing before starting
1. Child lock
"Time
Delay"
?
Child lock
can
be set
by pressing and holding the
Delay button
button and Time
Temp.
simultaneously.
-
-
-
Turn
on
the water
tap.
Load
laundry and close the door.
Place the detergent and fabric softener
in
the drawer.
?
Time Left
How to set "Time
-
-
?
When child lock is set, all buttons
are
inoperable.
-
?
To deactivate Child lock
system, press and hold
Delay"
Push Power button.
Turn the
Programme dial
to select
the program you require.
Push Time Delay button and set the
desired time.
Temp. and Time Delay button simultaneously again.
-
Push the Start/Pause button.
(":" blinks.)
Time Left
?
If Time Delay button is pushed, "3:00" is
displayed. The maximum delayed time is
19:00 hours and the minimum time is 3:00
?
If you want to
change the program when Child
lock is
hours.
active,
1. Press both and hold
Temp. and Time Delay together.
?
2. Press the Start/Pause button.
3.
Change the desired program
and press the
Each
time
?
Start/Pause button.
To cancel the time
?
Change
Time
or
can be set at any time and it is
canceled
when operational errors
automatically
occur. Also Child lock works when power is off.
18
delay, push
on
the Power
?
'expected time' from the
completion of washing cycle
process (Wash, Rinse, Spin).
Delay
present
program
The child lock
advances
button.
the desired
?
pushing of the button
delay by one hour.
is
to the
selected
According to
the condition
of water supply and
temperature, the delayed time and the actual
washing time
may vary.
washer
ow to use
H
Start/Pause
Rapid
?
the
By pressing
Rapid
button, Rapid function is
selected.
1.
1. Start
Rapid
?
?
?
Rapid function reduces the whole time
including the washing and rinsing time
about by half an hour.
is available in
Rapid
?
If
or
pause the
cycles.
temporary stop of wash cycle is needed,
push
that function has been selected.
turns on,
cycle
2. Pause
Whites, Coloureds
program.
If lamp
This Start/Pause button is used to start
wash
?
"Start/Pause" button.
After the pause button is pressed, the power
is turned off automatically 4 minutes later.
Programme
?
Power
9 programs
are
available
according to
the laundry
type.
1. Power
(Programme)
?
1.
Program
?
?
When Start/Pause button is
Coloureds program is
-
pushed,
automatically selected.
By turning the Program dial, the program is
selected in orders of "Coloureds U
Synthetic
U
Hand WashU
PumpU
Delicate
U
Wool
Rinse+Spin
U
U
Whites".
-
Whites
-
-
Coloureds
-
-
Delicate
Wool
Hand Wash
-
-
-
Rinse+Spin
Spin
Pump
Delay function,
it
Program
When the Power button is
pushed,
the
for Coloureds program.
And the other initial conditions as follows.
?
washer is
ready
So, if you
want to advance into the
washing cycle without selecting the
program, just push Start/Pause button
and then the washer will proceed.
2. Course
Synthetic
on
also be used.
2. Initial
?
Spin
To cancel the Time
can
U
Regarding to the laundry type for each program
Please refer to the page13.
-
Press the Power button to turn power
and off
Initial program
-
Coloureds Program / Main wash /
Normal Rinse/800 rpm / 40˚C
19
ow to use
H
washer
3.
Display
?
Completion of washing
When
washing cycle is completed,
is displayed on the "Multi
display".
"
"
1.
?
Special function display
When child lock is selected, the
is displayed.
"
"
?
?
When time
the
delay is selected, it shows
remaining times to finish the selected
4. Time left
During washing cycle, the remaining
washing time is displayed.
Recommended program
?
program.
-
2. Self
-
diagnose display
-
?
If the washer has
a
trouble, the trouble
-
type is displayed.
"
"
Sensing
:
Problem of
:
Door is not closed
:
Over load in moter.
:
Over load in moter.
:
Water inlet trouble
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
If this
to the
-
:
water pressure error
overfilling
-
-
-
?
trouble
Drainage
:
Imbalance trouble
:
Water temperature trouble
error letters are displayed, please refer
troubleshooting page24 and follow the
guide.
-
water
:
Whites
:
Coloureds
around 2 hours and 38 minutes
:
around 1 hour and 55 minutes
around 1 hour and 28 minutes
Synthetic
:
Delicate
:
around 58 minutes
Wool
:
around 58 minutes
Hand Wash : around 57 minutes
Rinse+
Spin
:
Pump
Spin
:
around 19 minutes
around 11 minutes
:
around 1 minute
The
washing time may vary by the
laundry, water pressure,
water temperature and other washing
amount of
conditions.
?
If the imbalance is detected
suds
or
if the
removing program works, the
wash time shall be
(Max. increasing
20
by
manufacturer.
longer.
45minutes.)
time is
aintenance
M
Before
cleaning
the washer interior,
unplug the electrical
power cord to avoid electrical
shock to avoid electrical shock hazards.
∀
The water inlet filter
"
-"
-
message will blink
error
detergent
on
the control
panel
when water does not enter the
drawer.
If your water is very hard
or
contains traces of lime
deposit,
the water inlet filter may
become
It
clogged.
is therefore a good
idea to clean it from time to time.
2. Unscrew the
1. Turn off the
water
water inlet
tap.
hose.
3. Clean the
filter
4.
using
Tighten
up
the inlet
a
hard bristle
hose.
brush.
∀
The drain pump filter
The drain filter collects threads and small
Check
!
regularly
CAUTION
that the filter is clean to
First drain it
using
1.
Open the lower cover
cap( )byusing
2.
left in the
smooth
laundry.
running of your
machine.
the drain hose and then open the pump filter to
whatever may have
Be careful when
objects
ensure
stopped
draining
it up.
if the water is hot.
Unplug the drain plug ( ),
allowing the water to flow out.
3. Take out any
At
foreign material
( ). After
cleaning, turn the pump filter ( )
from the pump filter
coin. Turn the drain
this time
plug( )topullout
water
the hose.
water does not flow any more, turn
plug (
the pump filter
close the lower
use a
flowing
remove
vessel to
on
prevent
to the floor. If the
( )
open to the left.
clockwise and insert the drain
)to
the
original place.
cover
cap.
100
3
1
3
2
2
21
aintenance
M
∀
Dispenser drawer
After
a
while
detergents
and fabric softeners leave
a
deposit
?
It should be cleaned from time to time with
a
?
If necessary it
from the machine
can
downward and
?
To facilitate
be removed
by pulling
cleaning,
completely
jet of running
in the drawer.
water.
by pressing
the catch
it out.
the upper
part of the fabric softener compartment
can
be removed.
max
max
∀
The drawer
Detergent
can
be cleaned
?
also accumulate inside the
occasionally
with
an
Once you have finished cleaning,
rinse cycle without laundry.
∀
?
recess
The
washing
?
?
replace
the drawer and
run a
continuously
clogs appliances,
builds up in
and if it is not
metal articles
washing drum is made of Stainless steel, specks
(paper clips, safety pins) which have been left in
The
drum should be cleaned from time to time.
Although
the
which should
drum
If you live in a hard water area, limescale
seen and it is not easily removed.
Over time the build up of scale
have to be replaced.
?
recess
old toothbrush.
washing
If you
use
descaling agents, dyes
or
bleaches, make
sure
they
places where
kept
it cannot be
in check these will
of rust
can
be caused
components that
Remove the
a
Never
22
use
spots
with
steel wool.
stainless steel
can
attack
are
suitable for
washing
part of your washing machine.
cleaning agent.
by
small
the drum.
use.
Descaler could contain
eventually
machine
aintenance
M
∀
Cleaning
your washer
1. Exterior
of your washer
can
extend its life.
The outside of the machine
can
be cleaned with
Proper
care
household
water and a neutral non abrasive
detergent.
Immediately wipe
Try
warm
off any
not to hit surface with
IMPORTANT: Do not
spills. Wipe
with
damp
cloth.
sharp objects.
methylated spirit,
use
diluents
or
similar
products.
2. Interior
Dry around the washer door opening, flexible gasket
always be clean to ensure a water tight seal.
Run washer
through
a
complete cycle using
Repeat
process if necessary.
NOTE
Remove hard water
∀
Winterizing
winterizing
1. Turn off water
an area
where
instructions to
should
as
washer safe.
freezing
can occur or
prevent damage
moved in
freezing temperatures,
to the washer:
supply tap.
electrical cord into
Plug
4. Add
areas
hot water.
deposits using only cleaners labeled
2. Disconnect hoses from water
3.
These
glass.
instructions
If the washer is stored in
follow these
and door
1gallon(3.8L)
a
supply
and drain water from hoses.
properly grounded
nontoxic recreational
electrical outlet.
vehicle(RV)
antifreeze to
empty wash drum. Close
door.
5. Set
spin cycle
and let washer
spin
Not all of the RV antifreeze will be
6.
Unplug
electrical power
7. Remove
Replace
dispenser
remove
through
a
expelled.
cord, dry drum interior, and close door.
drawer. Drain any water in
compartments and dry compartments.
drawer.
8. Store washer in
9. To
for 1minute to drain out all water.
an
uprignt position.
antifreeze from washer after
storage,
complete cycle using detergent.
run
empty washer
Do not add wash load.
23
roubleshooting guide
T
This
washing machine is equipped with automatic safety functions which detect and diagnose faults at an
early stage and react appropriately
When the machine does not function properly or does not function at all, check the following points before
you call the Service Department.
Possible Cause
Symptom
Rattling and
clanking noise
?
Solution
Foreign objects such as coins
safety pins maybe in drum or
or
Stop
washer and check drum
and drain filter.
If noise continues after washer
pump.
is restarted, call your authorized
service.
Thumping
sound
?
Heavy wash loads may produce
thumping sound. This is usually
If sound continues, washer is
probably out of balance. Stop and
normal.
redistribute wash load.
a
Vibrating
noise
?
Have all the transit bolts and
packing
?
Are all the feet
the
If not removed
been removed?
resting firmly
during
installation. See Installation for
on
removing
transit bolts.
Wash load
ground?
in drum.
unevenly distributed
Stop washer and
rearrange wash load.
Water leaks.
?
Fill hoses
at
?
tap
or
or
drain hose is loose
Check and
tighten
hose connections.
washer.
House drain
pipes
are
clogged.
Unclog
drain
pipe.
Contact
plumber
if necessary.
Too much
Oversudsing
detergent?
can cause
Water does not enter
washer
or
?
supply
is not
adequate
in
or
unsuitable
The formation of foam
water leaks.
Check another
tap in the house.
area.
it enters
slowly
Water
detergent
?
Water
?
Water inlet hose
?
The filter of the inlet hose
supply tap
completely open.
is not
are
Fully
kinked.
open tap.
Straighten
hose.
Check the filter of the inlet hose.
clogged.
Water in the washer
does not drain
drains
24
slowly.
?
Drain hose is kinked
?
The drain filter is
or
clogged.
Clean and
straighten
or
clogged.
Clean the drain filter.
the drain hose.
roubleshooting guide
T
Possible Cause
Symptom
Washer does not start
?
Electrical power cord may not
plugged in or connection
be
Solution
Make
plug
sure
fits
tightly
in wall
outlet.
may be loose.
?
House fuse blown, circuit
Reset circuit breaker
breaker
Do not increase fuse
tripped,or
a
power
outage has occurred.
If
problem
is
a
replace
capacity.
or
fuse.
circuit overload, have
it corrected
?
Water
supply tap
is not turned
by a qualified electrician.
on water supply tap.
Turn
on.
Washer won't
spin
Check that the door is
shut.
firmly
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the clothes
washer
begins to spin. The door
spin can be
must lock before
achieved.
Door does not open
Once started, the door can not be
for safety reasons.
opened
Wait
one or
two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash
cycle
delayed
time
The
washing time may vary by the
laundry, water
amount of
pressure, water temperature and
other using conditions.
If the imbalance is detected
suds
or
if the
program works, the
wash time shall be increased.
removing
25
roubleshooting guide
T
Possible Cause
Symptom
?
Water
?
Water
?
?
Solution
supply is not adequate in area
supply taps are not completely
open.
Water inlet hose
are
Fully open tap.
Straighten
kinked.
The filter of the inlet hose
Check another tap in the house.
clogged.
hose.
Check the filter of the inlet hose.
?
Drain hose is kinked
Clean and
?
The drain filter is
Clean the drain filter.
?
Load is too small.
Add 1
?
Load is out of balance.
balance the load.
?
The
appliance
or clogged.
clogged.
has
an
imbalance
detection and correction
system.
If
or
straighten
the drain hose.
2 similar items to
Rearrange
spinning
help
load to allow proper
individual
?
heavy articles are
loaded(as like) bath mat, both robe,
etc. this system may stop spinning or
even interrupt the spin cycle
altogether, if the imbalance is too
great even after several spin starts.
If the laundry is still too wet at the end
of the cycle, add smaller articles of
laundry to balance the load and
repeat the spin cycle.
?
Is the door
Close the door.
opened?
If"
"is not released, call for service.
Unplug the
power
plug
service.
?
If the water overfills due to the
water
"
?"
"
display.
"is
sensor
26
faulty
valve, you will get
displayed
if the water level
malfunction.
?
Over load in motor.
?
Over load in motor.
Close the water tap.
Unplug the power
Call for service.
plug.
and call for
M
emo
27
P/No.: 3828ER3007D
Download PDF

advertising