Washing Machine OWNER'S MANUAL WD(M)-1080F(H)D / 1085F(H)D WD(M)-1280F(H)D / 1285F(H)D WD(M)-1480F(H)D / 1485F(H)D WD-1288FHD / WD-1488FHD Thank you for buying a LG Fully Automatic Washing machine. Please read your owner's manual carefully, it provides on safe installation, use and maintenance. instructions Retain it for future reference. Record the model and serial numbers of your washing machine. P roduct Feature n 40% Jumbo drum LG's jumbo drum conventional wash about 40% can machines. A washing more bigger load than drum improves the wash performance. n More economical Intelligent Wash by Intelligent System Wash System detects the amount of load and water temperature, and then determines the optimum time to minimize energy and water washing n Direct Drive water level and consumption. System The advanced Brushless DC motor rotates the Drum without belt and n Wash Child-Lock The Child-Lock Rinse pressing n system has been used any button to Low noise speed change control to prevent children from the program during operation. system the amount of load and balance, it load to minimize the spinning noise level. By sensing n directly pulley. evenly distributes Auto Restart If the washing machine is turned off by a power failure, it will restart automatically from the position it stopped at adjusting accordingly. C ontents Warnings....................................................................................3 Specification ..............................................................................4 Installation..................................................................................5 Care before washing................................................................11 Adding detergent .....................................................................12 Function ...................................................................................13 How to use washer ..................................................................14 Maintenance ............................................................................21 Troubleshooting guide Terms of 2 Warranty .............................................................24 ...................................................................27 arnings W READ ALL INSTRUCTIONS BEFORE USE For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life. WARNING! ! IMPORTANT SAFETY INSTRUCTIONS WARNING : To reduce the risk of fire, electric shock, the ? Do not install be ? ? or store the washer where it will ? exposed to the weather. Do not tamper with controls. repair or replace any part of the washer attempt any servicing unless specifically instructions ? using or Do not wash published user-repair instructions ? or dry articles that have been in, washed in, soaked in, or spotted with explosive substances (such as wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, etc.) which may ignite or explode. To avoid such a result, carefully follow the or that you understand and have the skills to carry garment manufacturer's wash and out. instructions. Keep the area underneath and around your appliances free of combustible materials such lint, paper, rags, chemicals, etc. Close supervision is necessary if this is used by or near play other appliance. on, or appliance with, this or any Do not leave the washer door open. An open door could entice children to the door ? or Never reach into washer while it is ? The until the drum has ? inside hang can or try to To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household on ? moving. completely stopped. laundry process retardant of fabrics. Do not slam the washer door closed distribution crawl inside the washer. ? care force the door open when locked. This could result in damage to the washer. as children. Do not allow children to ? to persons when combustible recommended in the user-maintenance ? injury cleaned Do not or or washer, follow basic precautions, including the following: Wait reduce the flame panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning. Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS This grounded. In the event of malfunction or breakdown, grounding will reduce the risk by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance. Do not use an adapter or otherwise defeat the grounding plug. appliance must be of electric shock ? ? If you don't have the proper WARNING : outlet, consult an electrician. Improper connection of the equipment-grounding conductor can result in risk of electric qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance if it does not fit the outlet, have a proper outlet installed by a qualified electrician. shock. Check with a - 3 pecification S Power plug If the it supply cord is damaged, must be replaced by the manufacturer Drawer or a (For detergent and fabric softener) order to avoid or its service agents person in similarly qualified Control a hazard. panel Drain hose Door Lower cover Drum Adjustable Drain pump filter Lower Drain Name n Power supply : Front loading washing : 220 240, 50Hz 600mm(W) 65kg 7kg Size : Weight Wash capacity : n Max. Watt : n Spin speed : n n cover cap plug n n feet : - machine 600mm(D) 850mm(H) 2100W No spin/400/600/800/1000[WD(M)-1080F(H)D)/WD(M)-1085F(H)D)] No spin/400/800/1000/1200[WD(M)-1280(5)F(H)D/1288FHD] No spin/400/800/1000/1400[WD(M)-1480(5)F(H)D/1488FHD] n Water n Permissible water pressure The appearance and n : (10.7 /kg) 0.3-10kgf/ (30-1000kPa) specifications may be varied without notice to raise the units Accessories Inlet 4 :75 consumption hose(1EA) Option : Hot/Cold(2EA) Spanner quality. nstallation I Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. Transit bolts n The appliance is fitted with transit bolts to Removing n prevent internal damage during transport. transit bolts 1. To prevent internal damage during transport, the special 4 bolts are locked. Before operating the washer, remove the bolts ? If they along with the rubber vibration, along with the rubber bungs by slightly twisting the bung. Keep the 4 bolts and the spanner for future use. bungs. not removed, it may cause noise and malfunction. are 3. Take out the 4 bolts heavy ? Whenever the appliance is transported, the transit bolts must be refitted. cap 2. Unscrew the 4 bolts with the spanner 4. Close the holes with the caps supplied. supplied. 5 nstallation I n Installation place requirement Level floor Drain Hose Allowable Washer : under entire washer is 1˚ slope Power outlet : Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with than Laundry one Additional Clearance Tub For wall, door and floor approx. 2cm more appliance. (10cm : rear Do not place /2cm:right or store : modeling is required. side) & left laundry products washer at any times. They can damage the finish or on top of controls. 650 850 8 600 n BS Plug Safety Details (For U.K. User) IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN AND YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE This appliance Green and Yellow(Earth) must be earthed E Brown(Live) L Blue(Neutral) Fuse N Cord grip As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings the terminals in your plug, proceed as follows: The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the identifying letter E or by the earth symbol ( ) or coloured Green or Green and Yellow. The wire which is coloured Blue must be connected to the terminal which is marked with the letter N or The wire which is coloured Brown must be connected to the terminal which is marked with the letter L If a 13 amp 6 (BS 1363) plug is used, fit a 13 amp BS 1362 fuse. coloured Black. or coloured Red. nstallation I n Electrical connection 1. Do not use an extension cord or double adapter. supply cord is damaged, it must be replaced by the or similarly qualified person in order to avoid a hazard. Always unplug the machine and turn off the water supply 2. If the 3. 4. Connect the machine to 5. The n appliance Washing must be an manufacturer after so that the plug is easily its service agents use. earthed socket in accordance with current positioned or wiring regulations. accessible. Machine is to be connected to the water mains using new hose- sets and that old hose-sets should not be used. n Connecting water hose supply Water supply pressure must be between (0.3~10kg.f/cm2) 30kPa and 1000kPa Don't strip or crossthread when connecting Inlet hose to the valve. If the water supply pressure is more than 1000kPa, a decompression device should be installed. ? Two rubber seals are supplied with the water inlet hoses these are in order to prevent ? Hose connector Rubber seal water leaks. Check water tightness of washing machine connections by turning the completely ? tap on. Periodically check the condition of the replace the hose if necessary. hose and ? Hot water When your washer has tap Cold Cold Hot(option) Make sure that there is no kink hose and that it is not crushed. two on the valves, ? The Inlet hose which has red connector is for the hot water tap. ? If the washer has two valves, the energy is saved by using hot valve. water tap 7 nstallation I n Tap without Normal 1. Unscrew the fixing attach the screw thread & screw 2. Push the to rubber tap. connector up till the packing with the type inlet hose 3. Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. is in tap. Then tight contact tighten the 4 screws. n Tap without Normal 1. Untighten the upper thread & connector touch one 2. Push the upper the rubber screw. Rubber Connector Fixing tighten packing screw Middle the 4 Rubber connector connector up till packing contact with the Upper type inlet hose is in 3. Connect the water to the middle tight tap. Then pushing the supply hose connector, plate down. screws. Upper Connector packing Plate Upper ? In case large the diameter of the remove Guide the tap is Connector Water hose Middle guide plate. connector plate Turn the middle connector not ? to have water leaked. Connector ? Make sure that the rubber seal is inside the hose connector. ? To supply separate the water supply hose from the middle connector shut off the inlet hose plate tap. Then pull the down, pushing the down. Hose connector Rubber seal Used the horizontal Horizontal tap tap ? Your machine comes with only cold water connection. ? Extension tap Make sure that there not crushed. Square tap 8 are no kinks in the hose and that it is I n nstallation Installation of drain hose ca. ca. 145 100 cm cm ? max.10cm min.60cm ca. 105 When installing the drain hose sink, it tightly with a string. secure cm ? Proper securing protect water of the drain hose will the floor from damage due to leakage. Laundry tub ca. 100 cm Hose ca. 145 Retainer cm Tie 100cm min. 60cm max. ca. ? 100 Proper securing cm min.60cm max.10cm cm The drain hose should not be higher than ? 105 ? 100cm min. 60cm placed above the floor. of the drain hose will protect the floor from damage due water max. strap to leakage. When the drain hose is too long, do not force back into the washer. This will cause abnormal noise. 9 I n nstallation Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the floor the appliance on a solid and level surface, preferably in of a corner room. 2. If the floor is uneven, adjust the adjustable feet as required. (do not insert pieces Make sure of wood etc. under the that all four feet are feet) stable and resting on the floor and then check appliance is perfectly level. (use spirit level) that the a Adjustable Higher Adjustable feet Lower feet Diagonal Check When pushing down the edges of the washing machine top plate diagonally, machine should not all. (Please, move check both the up and down at of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the feets again. 10 C n are Caring before before washing washing 1. Care Labels Look for garment 2. label on your clothes. This will tell you about the fabric content of your and how it should be washed. a care Sorting get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly soiled one. To Soil 3. (Heavy, Normal, Light) (White, Lights, Darks) (Lint producers, Collectors) Color Separate Separate Lint Wash lint Caring n before Combine large clothes to amount of soil. according white fabrics from colored fabrics. and lint collectors producers separately. loading and small items in a than half the total wash load. Do not wash single items. This may load. Load cause an large items first. out-of-balance load. Add ? Check all that items should not be Large one or pockets two similar items. to make sure empty. Items such nails, hair clip, matches, pens, they are coins and keys more can damage as both your washer and your clothes. ? Close zippers, make sure snag ? on hooks and little to other clothes. Pre treat dirt and stains a strings that these items don't detergent by brushing dissolved in water onto stains like collars and cuffs to help shift dirt. 11 dding detergent A n Adding detergent 1. The Dispenser and fabric softener 3. Detergent dosage Drawer ? The detergent should be used according to of the detergent manufacture. the instruction max ? If too much detergent is recommended amount, occur and this will decrease the heavy malfunction) or cause ? Use powder loading ? Main wash only U ? ?PreWash+MainWashU used more than the load to suds too many the can washing result (Causing a motor. detergent only for the front washer. Detergent usage may need to be for water water temperature, adjusted hardness, size and soil level of the load. For best 2. results, avoid oversudsing. Adding Fabric Softener ( ) MAX MAX 125 ml 125ml Tips Full load Part load ? Do not exceed the maximum fill line. Overfilling can cause clothes. Do not leave the fabric softener in the Softener will during ? automatically cycle. 2 days. be added the last rinse Do not open the drawer when water is supplied. ? Solvents(benzene, etc) are not allowable. NOTE Do not pour fabric softener on the cloths directly 12 : 3/4 of the normal amount. Minimum load ? : 1/2 of full load. Detergent is flushed from the dispenser beginning of the cycle. the detergent drawer for more than (Fabric softener could harden) ? to early dispensing of the fabric softener which could stain ? according : manufacturer's recommendation. at unction F n Recommended Energy ※( ) : label data based WD(M) to the on program cotton 60˚C, 1080(5)F(H)D Fabric Program Cotton - according courses / laundry type tested in accordance with EN60456. 1280(5)F(H)D Proper Temp. (Option) Type Color fast garments Cotton-Eco Laundry type is the 60˚C in Cotton. (40˚C) Delicate Wool Hand Wash Quick 30 Main+(Pre) 40˚C Synthetic Polyamide, Acrylic, Polyester. (Cold, Main+(Pre) 30˚C,60˚C) Delicate laundry easily 30˚C damaged.(silk, curtains...) (Cold, 40˚C) Machine washable woolens with pure new wool only. 30˚C (Cold, 40˚C) "Hand Wash" marked delicate and wool Cold laundry. (30˚C,40˚C) Laundry type is the in Cotton and Synthetic. Pre Wash : If the laundry same is in in Liter KWh Minutes 7.0kg 75 1.33 163(159) 5.0kg 65 1.24 163(159) 2.0kg 52 1.2 153(149) 7.0kg 75 1.4 178 5.0kg 65 1.2 178 2.0kg 48 1.0 163 4.0kg 60 0.5 2.0kg 48 0.4 3.0kg 60 0.5 1.0kg 48 0.3 2.0kg 52 0.3 1.0kg 48 0.2 2.0kg 52 0.03 1.0kg 48 0.01 5.0kg 48 0.3 2.0kg 40 0.2 (Option) 60˚C same Energy in Load (Cold, (shirts, night dresses, Main+(Pre) pajamas...)and lightly soiled 30˚C, 40˚C, white cotton (underwear...) 95˚C) 30˚C (Cold, 40˚C) heavily soiled, "Pre Main Main Main Main Wash" Time Water Washing 92 67 61 60 course 30 is recommended. Pre Wash is available in Cotton-Eco, Cotton, Synthetic program. Water Temperature : Select the water temperature to the wash cycles. Always follow garment manufacture's care label or instructions when laundering. 13 ow to use H washer Delicate Wool Synthetic Cotton 1400 95 C 1000 60 Rinse Hold 800 40 Pre Wash Super 400 30 Main Wash Normal No Cold Time Time Save Hand Wash Cotton-Eco Quick 30 program Power 1. Cotton Start/Pause automatically selected upon power ? Press the ? Press the Start/Pause button. ? Initial condition Power( ) Wash Delay Rinse 3. Spin Temp. Spin Beep on/off on. ? The ? The button to start. Beep on/off function can be set by pressing and holding the Spin and Temp. button simultaneouly. Beep on/off function can be set at - Wash : Main wash any time and it is automatically canceled when power failure occur. - Rinse : 3 times Also the - - - Spin : 1400 rpm (1200 rpm, Water temperature Program : : 1000 rpm) 60˚C 4. Auto half load. ? Selecting ? Press the ? Select the conditions which you want to use, by pressing each button. Power( ) button to start. For selecting the each conditions, please refer to the page15~page20 Press the Start/Pause button. 14 on/off function works Cotton 2. Manual ? Beep when power is off. Auto half load saves you time and when money washing smaller loads. The washing machine is fitted with a self adjusting ? This water level system. system enables the machine to use the amount of water needed to wash and rinse the particular laundry load. in relation to the H ow to use washer Delicate Wool Synthetic Cotton Cotton-Eco Quick 30 program Power (1) (1) (2) (3) (4) Button Dial : : Time Time Save Hand Wash Start/Pause (2) Power Program Button : Start/Pause Button : Time Save Button (5) (6) (7) (8) Pre Wash Super Main Wash Normal Wash (4) (3) (6) (7) (8) Rinse Button : Time 60 800 40 400 30 Cold Spin Temp. (9) (10) Button (9) (10) Child lock : 95 C 1000 Spin Wash Button 1400 No Rinse (5) : Delay Rinse Hold Spin : Button : Water Delay Power Program ? 7 programs are available according laundry type. Power 1. Power - Cotton-Eco - Cotton - - ? Press the Power( on and off. power ? ) button to turn - - To cancel the Time Delay function, the Power( ) button should be pressed. Temp. - ? Wool Synthetic Cotton Synthetic Hand Wash Cotton-Eco Delicate Wool Hand Wash will Quick 30 program (Program) Quick 30 Lamp to the Delicate light up to indicate selected program. 2. Initial ? ? Program When the Power( ) button is pressed, the washer is ready for Cotton program. And the other initial conditions as follows. So, if you want to advance into the 1. ? / 1485F(H)D] ? [WD(M)-1480F(H)D -Cotton Program / Main wash / ? [WD(M)-1280F(H)D / 1285F(H)D] -Cotton Program / Main Wash / Normal Rinse / 1400 rpm / 60˚C Normal Rinse / 1200 rpm / 60˚C ? [WD(M)-1080F(H)D / 1085F(H)D] -Cotton Program / Main Wash / Normal Rinse / 1000 rpm / 60˚C When Start/Pause button is Cotton program is - By turning the pressed, the automatically selected. Program dial, the program is selected in order of "Cotton U washing cycle without changing the program, just press Start/Pause button and then the washer will proceed. Initial program Program Delicate U Synthetic U Wool U Quick 30U Cotton-Eco". Regarding to the laundry type for each program Please refer to the page13. 2. Course - Cotton-Eco - - Cotton - - - Synthetic - Wool Hand Wash Quick 30 Delicate 15 ow to use H washer Start/Pause Time Save Time Save Start/Pause 1. Start ? 1. Time Save This Start/Pause button is used to start wash cycle pause the wash or ? cycle. ? 2. Pause This option of wash program. To a ? If temporary stop of wash cycle is needed, press "Start/Pause" button. ? When in automatically ? after 4 minutes. NB. The door will not open before 1 to 2 minutes when Pause is selected, or 16 at the end of the wash cycle. be used to reduce the time option press once the Time Save before the wash program is started. ? Pause, the power is turned off this use button can This option program. is not available with Quick 30 H ow to use washer Child lock Wash By pressing ? Pre Wash the Wash button, the wash type Main Wash can Wash be selected. - Main Wash - Pre Wash + Wash Rinse If you choose to lock the buttons on the control assembly to prevent tampering, this Main Wash function may be selected. 1. Main Wash ? Main Wash normally course soiled If the laundry Main Wash" ? is available for lightly or ? laundry. 2. Pre Wash ? 1. Child lock is + "Pre Wash Wash + by pressing and holding the simultaneously. Rinse ? When child lock is set, all buttons ? To deactivate Child lock system, press and hold the Wash and Rinse button simultaneously again. Synthetic program. The required lamp identification. be set is effective. Pre Wash is available in Cotton-Eco, Cotton and can Main Wash heavily soiled, course Child lock Wash and Rinse button will light up for Wash ? To change are inoperable. Rinse to the desired program, whilst in child lock mode. 1. Press and hold both Wash and Rinse button together once again. 2. Press the Start/Pause button. 3. Select the desired program and press the Start/Pause button again. Change the desired Wash ? Rinse Start/P program Start/P The child lock can be set at any time and it is canceled when operational errors Also Child lock works when power is off. automatically occur. 17 H ow to use washer Rinse Rinse Hold Time By pressing ? the Rinse Super button, the Rinse type Normal be selected. - - - Rinse - Time can Delay Super Normal + Rinse Hold 1. Time Super + Rinse Hold Delay Preparing washing before starting "Time Delay" - Cotton-Eco / Cotton / Synthetic performs 3 - Rinses - ? Time Delay Normal 1. Normal ? Delay Wool / Hand Wash /Quick Turn on the water tap. Load laundry and close the door. Place the detergent and fabric softener in the drawer. 30 / Delicate performs 2 Rinses ? 2. Super How to set "Time - - ? Normal ? Use the + 1 more rinse time. - Super rinse when additional rinsing is desired to remove detergent soiled loads. excess dirt - ? 3. Rinse Hold Is selected by pressing repeatedly this function leaves clothes in the without ? entering into water after a rinse Press the spin speed or program. Start/Pause button again to start Each pressing of the delay by one hour. ? To cancel the time Power( ? If you want to drain only, select the No program. The required lamp identification. 18 Time will light up for Spin ? ) button advances time delay, press the button. 'expected time' from the completion of washing cycle process (Wash, Rinse, Spin). Delay present or program. ? Delay button is pressed, "3:00" is displayed. The maximum delayed time is If Time ? Start/Pause button to cancel the Rinse Hold function and select button.(":" blinks.) hours. spin. If you want to drain and spin, when Rinse Hold function is proceed, Press the Press the Start/Pause 19:00 hours and the minimum time is 3:00 the Rinse button washer; suspended in the the desired time. and ? Delay" Power( ) button. Turn the Program dial to select the program you require. Press Time Delay button and set Press is to the selected According to the condition of water supply and temperature, the delayed time and the actual washing time may vary. H ow to use washer Spin 1000 1200 1400 800 1000 1000 600 800 800 400 400 No No Spin Spin By pressing can Spin Spin the Spin button, the The required lamp identification. - 400 - 600 - 800 - 800 - 800 - 1000 - 1000 - 1000 - 1200 - 1400 ? 40 Cold - No Spin U 400 U U ? (600) Cotton [WD(M)-1480F(H)D / 1485F(H)D] 1400U NoSpinU 400U 800U 1000 [WD(M)-1280F(H)D / 1285F(H)D] 1200U NoSpinU 400U 800U 1000 [WD(M)-1080F(H)D / 1085F(H)D] 1000U NoSpinU 400U 600U 800 - NoSpinU 400U(600) 800U (600) temperature according can be selected as to the program. Cotton-Eco U 40˚C Cotton - Synthetic 40˚C - U 60˚C U Cold U 30˚C Delicate & Wool & Quick 30 U 40˚C U Cold 30˚C Hand Wash 30˚C U 40˚C required temperature lamp identification. NoSpin U 800 U 1000 U Temperature The For the Wool / Hand Wash 400U - (600)U Temp Cold below Cold U Delicate 400U - the 60˚CU 95˚CU ColdU 30˚CU 40˚C - Synthetic 800U 1000U - Water 60˚C - - By pressing to the - (1200)(1400) Temp. selected. 30 Cotton-Eco 800 U 1000 U the Temp. follows. as the on button, the water temperature can be 1. Water according on -30˚C/40˚C/60˚C/95˚C Spin selection is available spin is selected stops will light up for 95 C - 400 program Spin" Water spin speed - Spin speed to remove this 60 - the washer Wool, Delicate and Hand Wash program. [WD(M)-1280(5)F(H)D/ [WD(M)1480(5)F(H)D / 1288FHD] 1488FHD] 400 - possible rinse when "No Spin - ? It is Spin" is selected, draining water. [WD(M)-1280(5)F(H)D [WD(M)-1480(5)F(H)D /1288FHD] /1488FHD] No Spin No Spin - spin If "No after be chosen. [WD(M)-1080F(H)D /1085F(H)D] No Spin 1. ? 400 No Spin [WD(M)-1080F(H)D / 1085F(H)D] ? 2. No more detailed will light up for information, please refer to the page13. No Spin Quick 30 400U (600)U 800U 1000U 1400U NoSpin 19 H washer ow to use 3. Display ? Completion of washing When washing cycle is completed, is displayed on the "Multi display". " 1. ? Special function display When Child lock is selected, the is displayed. " ? " delay is selected, it shows remaining times to finish the selected 4. Time left ? During washing cycle, the remaining washing time is displayed. ? Recommended program When time the program. diagnose display If the washer encounters operation, displayed. - a fault during - the associated fault will be - - " " : Water pressure sensing error - " " " " " " : Problem of overfilling : Door is not closed : Over load in motor : Over load in motor : Water inlet trouble : Drainage : Unbalanced load : Water water ? " " " " " " " " " " trouble temperature trouble If these error letters are displayed, please refer to the troubleshooting page26 and follow the guide. 20 manufacturer. - - ? by ※( ) : WD(M) 1080(5)F(H)D / 1280(5)F(H)D - 2. Self " Cotton-Eco : around 2 hours and 58 minutes Cotton : around 2 hours and Synthetic : 43(39) minutes around 1 hours and 32 minutes Delicate : around 1 hour and 7 minutes Wool : around 1 hour and 1 minutes Hand Wash Quick 30 : : around 1 hour around 30 minute The washing time may vary by the laundry, water pressure, water temperature and other washing conditions. amount of ? If an suds unbalanced load is detected or if the the removing program operates, wash time may be extended. (Max. increasing time is 45minutes.) aintenance M Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. n The water inlet filter " -" - message will blink error detergent on the control panel when water does not enter the drawer. If your water is very hard or contains traces of lime deposit, the water inlet filter may become It clogged. is therefore a good idea to clean it from time to time. 2. Unscrew the 1. Turn off the water water inlet tap. hose. 3. Clean the filter 4. using Tighten up the inlet a hard bristle hose. brush. n The drain pump filter The drain filter collects threads and small Check ! regularly CAUTION that the filter is clean to First drain using 1. Open the lower cover cap( )byusinga 2. left in the smooth laundry. running of your machine. the drain hose and then open the pump filter to whatever any threads Be careful when objects ensure objects. or draining if the water is hot. Unplug the drain plug ( ), allowing the water to flow out. 3. Remove any At foreign from the pump filter coin. Turn the drain this time plug( )topullout water the hose. water does not flow any more, turn plug ( the pump filter close the lower use a flowing remove vessel to on prevent to the floor. When ( ) open to the left. cleaning, material ( ). After turn the pump filter ( clockwise and insert the drain )to the original place. cover cap. 100 3 1 3 2 2 21 ) aintenance M Dispenser drawer n After a while detergents and fabric softeners leave ? It should be cleaned from time to time with ? If necessary it can be removed a deposit in the drawer. a jet of running water. completely from the machine by pressing ? by pulling it out. cleaning, the upper part the catch downward and To facilitate of the fabric softener compartment can be removed. max max The drawer n Detergent can be cleaned ? also accumulate inside the n without cycle The washing If you live in seen with occasionally Once you have finished rinse ? recess a recess old toothbrush. an cleaning, replace the drawer and run a laundry. drum hard water area, limescale may and thus not which should easily continuously build up in places where it cannot be removed. Over time the build up of scale clogs appliances, and if it is not kept in check these may have to be replaced. ? Although the washing drum is made of Stainless steel, specks of rust can articles (paper clips, safety pins) which have been left in the drum. ? The ? If you washing use be caused descaling agents, dyes or bleaches, make Descaler may contain chemicals that may Remove any 22 use small metal drum should be cleaned from time to time. sure they are suitable for washing use. Never by spots with steel wool. a stainless steel damage part of your cleaning agent. washing machine. machine aintenance M n Cleaning your washer 1. Exterior of your washer can extend its life. The outside of the machine can be cleaned with Proper care household water and a neutral non abrasive detergent. off any Immediately wipe Try warm not to hit surface with IMPORTANT: Do not spills. Wipe with cloth. damp sharp objects. methylated spirits, use diluents or similar products. 2. Interior Dry around the washer door Run washer through n and door glass. hot water. complete cycle using Remove hard water deposits using only cleaners labeled as washer safe. Cold condition If the washer is stored in temperatures, an area 4. Add freezing may occur or moved in freezing prevent damage to the washer: supply tap. 2. Disconnect hoses from water Plug where follow these instructions to 1. Turn off water 3. gasket if necessary. Repeat process NOTE a flexible opening, electrical cord into 1gallon(3.8L) a supply and drain water from hoses. properly grounded of nontoxic recreational electrical outlet. vehicle(RV) antifreeze into an empty wash drum. Close the door. 5. Set spin cycle and let washer spin Not all of the RV antifreeze will be 6. Unplug electrical power 7. Remove 9. To remove through a an expelled. cord, dry the drum interior, and close the door. dispenser drawer, 8. Store washer in for 1minute to drain out all water. drain and dry excessive water from the compartments. upright position. antifreeze from washer after storage, complete cycle using detergent. run empty washer Do not add wash load. 23 T roubleshooting guide This washing machine is equipped with automatic safety functions diagnose faults at an early stage and react appropriately. When the machine does not function properly or does not function following points before you contact your service provider. all, check the at Possible Cause Symptom Rattling and clanking noise which detect and ? Solution Foreign objects such as coins safety pins maybe in drum or or Stop washer and check drum and drain filter. If noise continues after washer pump. is restarted, call your authorized service centre. Thumping sound ? Heavy wash loads thumping sound. a may produce This is usually normal. Vibrating noise ? ? redistribute wash load. Have all the transit bolts and packing If not removed been removed? Are all the feet the If sound continues, washer is out of balance. Stop and probably during installation, refer to Installation guide resting firmly on for removing transit bolts. Wash load may be distributed ground? in drum. Stop unevenly washer and rearrange wash load. Water leaks. ? Fill hoses at ? tap or or drain hose are loose Check and tighten hose connections. washer. House drain pipes are clogged. Unclog drain pipe. Contact plumber if necessary. Too much Oversudsing detergent detergent may foaming which or cause unsuitable excessive may result in water leaks. Water does not enter washer or ? it enters slowly Water supply is not adequate in Check another tap in the house. area. ? Water ? Water inlet ? The filter of the inlet supply tap completely open. is not hose(s) are Fully kinked. hose(s) are open tap. Straighten hose(s). Check the filter of the inlet clogged. Water in the washer does not drain drains 24 slowly. ? Drain hose is kinked ? The drain filter is or clogged. or clogged. Clean and straighten Clean the drain filter. hose(s). the drain hose. roubleshooting guide T Possible Cause Symptom Washer does not start ? Electrical power cord may not plugged in or connection be Solution Make plug fits tightly sure in wall outlet. may be loose. ? House fuse blown, circuit Reset circuit breaker breaker Do not increase fuse tripped,or a power outage has occurred. If problem is a replace fuse. capacity. or circuit overload, have it corrected ? Water supply tap is not turned Turn on by a qualified electrician. water supply tap. on. Washer won't spin Check that the door is shut. firmly Close the door and press the Start/Pause button. After pressing the Start/Pause button, it may take a few moments before the clothes washer begins to spin. The door spin can be must lock before achieved. Door does not open Once started, the door can not be for safety reasons. opened Wait one or two minutes before opening the door to give the electric locking mechanism time to release. Wash cycle delayed time The washing time may vary by the laundry, water amount of pressure, water temperature and other using conditions. If the imbalance is detected suds or if the program works, the wash time shall be increased. removing 25 T roubleshooting guide Possible Cause Symptom ? Water ? Water ? ? Solution supply is not adequate in area supply taps are not completely open. Water inlet hose(s) are The filter of the inlet kinked. hose(s) are Check another tap in the house. Fully open tap. Straighten hose(s). Check the filter of the inlet hose(s). clogged. ? Drain hose is kinked Clean and ? The drain filter is Clean the drain filter. ? Load is too small. Add 1 ? Load is out of balance. balance the load. ? The has an unbalance detection and correction system. If individual are heavy articles or straighten the drain 2 similar items to Rearrange spinning load to allow proper loaded Is the door Close the door. opened? If" "is not released, call for service. Unplug the power plug service. Water overfills due to the faulty water valve. 26 help bath mat, both robe, ? ? hose. etc.), this system may stop spinning or even interrupt the spin cycle altogether. If the laundry is still too wet at the end of the cycle, add smaller articles of laundry to balance the load and repeat the spin cycle. (ex. ? appliance or clogged. clogged. Close the water Unplug the tap. power Call for service. ? Water level ? Over load in motor. ? Over load in motor. sensor has malfunctioned. plug. and call for T erms of Warranty What Is Not Covered: ? Service ? If the product rating plate. ? If the fault is caused by accident, neglect, If the fault is caused by ? trips to your home to teach you how to is connected to any voltage use the product. other than that shown misuse or on the Act of God. factors other than normal domestic use or use in accordance with the owner's manual. ? Provide instruction ? If the fault is caused ? Noise or on use by pests product for or change example, rats vibration that is considered normal for sound, spin sound, ? of Correcting or the or set-up of the product. cockroaches etc.. example water drain warming beeps. the installation for example, levelling the of product, adjustment drain. ? ? Normal maintenance which recommended Removal of foreign objects fuses in Correction of unauthorized ? Incidental possible ? If this or or example, grit, nails, correct house Replace ? the owner's manual. / substances from the machine, pump and inlet hose filter for ? by wiring or the including bra wires, buttons etc. correct house plumbing. repairs. consequential damage to personal property appliance. caused by defects with this product is used for commercial purpose, it is not warranted. (Example : Public places center, dormitory) such as public bathroom, lodging house, training If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the replacement defective part, shall be borne by the owner. of 27 a For U.K. Customer CUSTOMER SERVICES : 0870-592-9929(Service Force) Mon.-Fri. 8:30AM P/No.: 3828ER3006X LGEUK SERVICE WEB-SITE : - 5:30PM www.lgelectronics.co.uk
advertising