LG | WM-1437LFD | LG WM-1437BFD Owner’s Manual

For U.K. Customer
P/No.:3828ER3054T
CUSTOMER SERVICES Tel.
:
Fax.
:0870-872-7337
LGEUK SERVICE WEB-SITE
:
0870
-
873
-
LGLG(5454)
http://uk.lge.com
WD-1237(0~9)FD(M)
WD-1437(0~9)FD(M)
WD-1637(0~9)FD(M)
WM-1437WFD
WM-1437BFD
WM-1437SFD
WM-1437LFD
WM-1437PFD
WM-1437RFD
P
roduct Feature
Direct Drive
System
The advanced Brushless DC motor
belt and
directly
drives the drum without
pulley.
Water Circulation
Spray detergent
solution and water onto the load
continuously.
thoroughly during wash cycle.
The detergent suds can be removed more easily by the water shower during rinse
cycle. The water circulation system uses both water and detergent more efficiently.
Clothes
are
soaked
more
quickly
and
Built-in Heater
Internal heater
automatically
heats the water to the best
temperature
on
selected
the
settings
cycles.
Child Lock
The Child lock
prevents children from pressing any button
to
change
during operation.
More economical
by Intelligent Wash System
System detects the amount of load and water temperature, and then
optimum water level and washing time to minimize energy and water
Wash
Intelligent
determines the
consumption.
Low noise
speed control system
By sensing the amount of load and balance,
spinning noise level.
Safety device (Aqua lock)
Aqua lock System is designed for detecting
water from flooding over the floor.
Using
the RLM
it
evenly
water leak
(Remote Laundry Monitor)
Display
Unit
can
be
during operation
to
prevent
[WD-1*37(0~9)FDM]
The RLM monitors status of your washer and/or
into any power outlet in your home.
The RLM
distributes load to minimize the
dryer.
purchased separately
You
can
plug
the
display
for this washer.
Steam
Washing and Refresh
Washing features upgraded washing performance with
consumption. Refresh cycle reduces wrinkles from dry clothes.
Steam
low energy
Automatic Wash Load Detection
Automatically
C
detects the load and
optimizes
the
washing
time.
ontents
Warnings ....................................................................................................................3
Specification ................................................................................................................4
Installation ...................................................................................................................5
Care before
washing .................................................................................................11
Adding detergent .......................................................................................................12
Function
How to
..................................................................................................................14
use
washer ....................................................................................................15
Maintenance ..............................................................................................................23
2
Troubleshooting guide ...............................................................................................27
Terms of Warranty .....................................................................................................30
unit
W arnings
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE
For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
WARNING!
!
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock,
the
?
Before
installation, check exterior damages. If it has,
Do not install
be
?
?
weather.
Do not
repair or replace any part of the washer
attempt any servicing unless specifically
published user-repair instructions that you
understand and have the skills to carry out.
Keep the area underneath and around your
appliances free
of combustible materials such
lint, paper, rags, chemicals,
?
?
?
as
Do not leave the washer door open.
An open door could entice children to
door or crawl inside the washer.
?
To avoid such
laundry process
hang
on
?
reduce the flame retardant
?
of fabrics.
result, carefully follow the garment
a
manufacturer's wash and
?
Do not wash
or
dry
Do not
care
instructions.
articles that have been cleaned
in, washed in, soaked in,
or
as
wax,
spotted
or
try
to force
When the machine
runs
at
high temperature,
the
unplug
appliance
removing the fuse or switching off the circuit breaker
attempting any maintenance or cleaning.
When unplugging power cord, do not pull out by
grasping the cord. Otherwise, the power cord may
be damaged.
Never attempt to operate this appliance if it is
damaged, malfunctioning, partially disassembled, or
has missing or broken parts, including a damaged
cord or plug.
Before discarding an old machine unplug it. Render
the plug useless. Cut off the cable directly behind
the appliance to prevent misuse.
When a product was under water, Please call
before
?
the
running.
completely stopped.
can
(such
from the power supply or disconnect
the washer at the household distribution panel by
Never reach into washer while it is
The
Do not slam the washer door closed
this
etc.
supervision is necessary if this appliance is
by or near children or infirm persons.
Do not allow them to play on, with, or inside this
or any other appliance.
Keep washer away from fire.
?
substances
front door may be very hot. Don't touch it.
?
To minimize the possibility of electric shock,
Close
Wait until the drum has
explosive
the door open when locked. This could result in
damage to the washer.
used
?
or
oiled clothes.
?
or
?
using
explode. Oil may remain in the tub after a whole
cycle resulting in fire during drying. So, do not load
tamper with controls.
recommended in the user-maintenance instructions
?
when
oil, paint, gasoline, degreasers, dry-cleaning
solvents, kerosene, etc.) which may ignite or
store the washer where it will
or
exposed to the
Do not
or
injury to persons
combustible
do not install.
?
or
washer, follow basic precautions, including the following:
?
service center. The risk of electric shock and fire.
with
push down the door excessively,
topple over the washer.
when washer door open.
This could
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This
appliance must be grounded.
In the event of malfunction
or breakdown, grounding will reduce the risk of electric shock by providing a path
appliance is equipped with a cord having an equipment-grounding conductor and grounding plug.
The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
Do not use an adapter or otherwise defeat the grounding plug.
of least resistance for electric current. This
?
?
If you don't have the proper
WARNING :
outlet, consult
an
electrician.
Improper connection of the equipment-grounding conductor can
qualified electrician or serviceman
the plug provided with the appliance
a
-
if you are in doubt
if it does not fit the
as
to whether the
result in risk of electric shock. Check with
appliance
is
properly grounded.
Do not
modify
outlet, have a proper outlet installed by a qualified electrician.
3
S pecification
Drawer
Name
:
Front
:
220-240
Size
:
600mm(W)
Weight
:64kg
Power
supply
loading washing
2100W
machine
V~,50 Hz
x
640mm(D)
Max.Watt
:
Wash
capacity
:8kg
Water
consumption
:
52ℓ(6.5ℓ/ kg)
Permissible water pressure
:
0.3-10
Spin speed
:
(Wash)
/ 1100W
x
850mm(H)
(Steam)
2
kgf/cm (30-1000 kPa)
/400/600/800/1000/1100/1200
[WD-1237(0~9)FD(M)]
/400/600/800/1000/1200/1400
[WD-1437(0~9)FD(M)/WM-1437WFD/WM-1437BFD/WM-1437SFD/
WM-1437LFD/WM-1437PFD/WM-1437RFD]
/400/600/800/1000/1200/1600
[WD-1637(0~9)FD(M)]
The appearance and
specifications may
be varied without notice to raise the units
Accessories
Inlet
4
hose(1EA)
Option
:
Hot/Cold(2EA)
Spanner
quality.
nstallation
I
Install
or
store where it will not be
exposed
to
temperature below freezing
or
exposed
to the
weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine
carpeted floor.
In countries where there
vermin,
pay
all times.
particular
are areas
attention to
Any damage which may
appliance guarantee.
be caused
is installed
on a
which may be subject to infestation by cockroaches or other
keeping the appliance and its surroundings in clean condition at
by
cockroaches
or
other vermin will not be covered
by
the
Transit bolts
The
?
is fitted with transit bolts to
appliance
and all transit bolts must be
Packing
removed before
When
sure
prevent internal damage during transport.
using
unpacking
to
remove
the washer.
the base, be
the additional
packing support in
packing.
the middle of
the base
Removing
(Packing support may not
be used depending on
models.)
transit bolts
1. To
prevent internal damage during
transport, the special 4 bolts are locked.
Before operating the washer, remove
the bolts
?
If
they
along
with the rubber
vibration,
2. Unscrew the 4 bolts with
the spanner
along with the rubber
bungs by slightly twisting the bung. Keep
the 4 bolts and the spanner for the future
bungs.
not removed, it may cause
noise and malfunction.
are
3. Take out the 4 bolts
heavy
use.
?
Whenever the
appliance
is
transported,
the
transit bolts must be refitted.
4. Close the holes with the caps
supplied.
supplied.
5
nstallation
I
Installation place requirement
Level floor
Allowable
:
slope
Power outlet
under entire washer is 1˚
:
Must be within 1.5 meters of either side of location of
washer. Do not overload the outlet with
than
more
one
appliance.
Additional Clearance
:
For wall, door and floor
(10cm
modeling is required.
/2cm:right & left side)
place or store laundry products on top
: rear
Do not
any times.
They
can
damage
the finish
or
of washer at
controls.
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not
impeded by carpets, rug etc.
Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the
washer.
If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove, an insulation(85x60cm)
?
?
covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two
The washer must not be installed in rooms where the temperature can drop below 0°C.
?
appliance.
Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown.
Adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of
approximately 20mm is left between the top of the washer and the underside of the work-top.
?
?
BS
Plug Safety Details (For
U.K.
User)
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
This
Green and
appliance
must be earthed
Yellow(Earth)
E
Brown(Live)
L
Blue(Neutral)
Fuse
N
Cord
grip
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured Green and Yellow must be connected to the terminal in the plug which is marked with the letter E
or
by the
earth
symbol
or
coloured Green
or
Green and Yellow.
The wire which is coloured Blue must be connected to the terminal which is marked with the letter N
or
The wire which is coloured Brown must be connected to the terminal which is marked with the letter L
If
a
13 amp
6
(BS 1363) plug
is
used, fit
a
13 amp BS 1362 fuse.
coloured Black.
or
coloured Red.
nstallation
I
Electrical connection
1. Do not
use an extension cord or double adapter.
supply cord is damaged, it must be replaced by the
qualified person in order to avoid a hazard.
Always unplug the machine and turn off the water supply
2. If the
3.
4. Connect the machine to
5. The
?
?
?
appliance
must be
an
manufacturer
after
so
that the
plug
is
easily
its service
agents
or
similarly
use.
earthed socket in accordance with current
positioned
or
wiring regulations.
accessible.
Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by
inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst
under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
If the appliance is delivered in the winter months and temperatures are below freezing : Place the washing
machine at room temperature for a few hours before putting it into operation.
CAUTION
CAUTION
concerning
the Power Cord
Most
appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit
which powers only that appliance and has no additional outlets or branch circuits. Check the
specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords,
frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions
could result in electric shock or fire. Periodically examine the cord of your appliance, and if its
appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched,
closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where
the cord exits the appliance.
Washing
Machine is to be connected to the water mains
using
new
hose-sets and old hose-sets should
not be used.
Connecting
water
supply
hose
▶Water
supply pressure must be between 30kPa and 1000kPa
(0.3~10kgf/cm)
▶Don't strip or crossthread when connecting Inlet hose to the valve.
▶If the water supply pressure is more than 1000kPa, a decompression
2
device should be installed.
?
Two rubber seals
are supplied with the water inlet hoses. They
preventing water leaks.
Make sure the connection to taps is tight enough.
Periodically check the condition of the hose and replace the
are
?
?
?
used for
hose if necessary.
Make sure that there is
no
kink
on
the hose and that it is not
crushed.
▶When your washer has
?
?
Hose connector
If the washer has two
After
if water leaks from the
of faucet for water
case
completing connection,
supply. In
faucet into the adaptor.
tap.
valves, the energy is saved by using hot
valve.
Rubber seal
NOTE
two valves.
The Inlet hose which has red connector is for the hot water
hose, repeat the same steps. Use the most conventional type
or too big, remove the spacing ring before inserting the
the faucet is square
7
nstallation
I
Normal Tap without thread &
1. Unscrew the fixing
attach the
screw
to
screw
2. Push the
rubber
tap.
3. Push the
connector up till the
packing
with the
type inlet hose
is in
tight
supply hose
vertically upwards so that the
rubber packing within in the
hose can adhere completely to
the tap and then tighten it by
screwing it to the right.
contact
tap. Then tighten the
4
screws.
Normal Tap without thread &
1. Untighten the upper
connector
touch type inlet hose
one
2. Push the upper
the rubber
screw.
?
In
case
large
the diameter of the
remove
the
connector up till
packing
contact with the
tighten
the 4
is in
3. Connect the
tap. Then
pushing
the
supply
hose
connector,
plate
down.
screws.
tap is
Turn the middle connector not
to have water leaked.
?
Make
sure
that the rubber seal
is inside the hose connector.
?
To
separate the
water
supply
hose from the middle connector
shut off the
inlet hose
plate
Unable water
water
to the middle
tight
guide plate.
?
?
water
tap. Then pull the
down, pushing the
down.
Tap for connectoring
hose.
?
Make
sure
that there
are no
kinks in the hose and that it is
not crushed.
8
I
This
nstallation
equipment
is not
designed
for maritime
use or
for
use
mobile installations such
as
caravans, aircraft etc.
Turn off the
stopcock
if there is
especially
When disposing
if the machine is to be left for any length of time
floor drain(gully) in the immediate vicinity.
(e.g. holiday),
no
of the appliance, cut off the mains cable, and destroy the plug Disable the
prevent young children being trapped inside.
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk
door lock to
of suffocation !
Keep
all
packaging
well away from children
Installation of drain hose
?
When
installing the drain hose sink,
it tightly with a string.
Proper securing of the drain hose will
protect the floor from damage due to
water leakage.
secure
?
?
The drain hose should not be
than 100
cm
washer does not drain
?
placed higher
above the floor. Water in the
Proper securing
or
drains
slowly.
of the drain hose will
protect the floor from damage due
to water
leakage.
?
When the drain hose is too
long,
do not
force back into the washer. This will
abnormal noise.
cause
9
I
nstallation
Level
adjustment
1.
Adjusting
the
washing
machine level
properly prevents
excessive
noise and vibration.
Install the
corner
appliance
of the
NOTE
on a
solid and level floor surface,
preferably
in
a
room.
Timber
or
may contribute to
suspended type flooring
excessive vibration and unbalance
errors.
2. If the floor is uneven,
adjust the adjustable feet as required.
pieces of wood etc. under the feet)
Make sure that all four feet are stable and resting on the floor and
then check that the appliance is perfectly level. (use a spirit level)
After the washer is level, tighten the lock nuts up towards of the base of
the washer. All lock nuts must be tightened.
(do
※
not insert
NOTE
In the
case
platform,
that the
washing machine is installed
securely fastened in order
risk that it might fall off.
on a
raised
it must be
to eliminate the
Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the machine
should not move up and down at all. (Please, check both of two directions)
If machine rocks when pushing the machine top plate diagonally, adjust the feet again.
Concrete floors
?
The installation surface
?
Install washer
?
Position each foot
Tile floors
on a
on
Tread Mate is
a
?
?
clean, dry and level.
the Tread Mate and level the machine
pieces
on
to
the
dry tile where
to suit.
machine is
to
(Cut Tread
be
possible
install the washer in
one
of the
corners
※
Insert the rubber cups to reduce vibration.
※
You
can
slipping.
(Suspended floors)
Wooden floors are particularly susceptible to vibration.
To prevent vibration we recommend you place rubber cups under each foot,
at least 15mm thick under the washer, secured to at least 2 floor beams with
If
Mate into 70x70
placed.)
self adhesive material used on ladders & steps that prevents
Wooden floors
?
be
(Slippery floors)
sections and stick the
※
must
flat hard floor.
obtain the rubber cups
of the
room,
screws.
where the floor is
(p/no.4620ER4002B) from the
LG
svc
more
stable.
dept.
Important!
Proper placement and levelling of the washer ensure long, regular and reliable operation.
The washer must be absolutely horizontal and stand firmly in position.
?
?
?
?
?
It must not "Seesaw" across corners under load.
The installation surface must be clean, free from floor wax and other lubricant coatings.
Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur.
10
mm
C
are
before
Before the first
Select
washing
washing
cycle (COTTON 60°C, add a half load
without clothing. This will remove residues and
during manufacturing.
a
of
detergent)
allow the unit to wash
water from the drum that may have been left
Caring before washing
1. Care Labels
Look for
a care label on your clothes. This will tell you about the fabric content of your
how it should be washed.
2.
garment and
Sorting
To
get the best results, Sort clothes into loads that can be washed with the same wash cycle.
temperature and spin speed and different fabrics need to be washed in different ways.
Water
Always sort dark colors from pale colors
occur causing discoloration of white etc.
soiled
and whites. Wash
If
possible,
one.
Soil
(Heavy, Normal, Light)
Color (White, Lights, Darks)
Lint (Lint producers, Collectors)
3.
separately as dye and lint transfer can
heavily soiled items with lightly
do not wash
Caring
before
Combine
Separate
Separate
clothes
according
to amount of soil.
white fabrics from colored fabrics.
Wash lint
producers
separately.
and lint collectors
loading
large and
small items in
a
load. Load
large items first. Large items should not
be
more
than half
the total wash load.
Do not wash
single items.
This may
cause an
out-of-balance load. Add
Check all
?
two similar items.
one or
pockets
to make
sure
that
they
empty. Items such as nails, hair clip,
matches, pens, coins and keys can damage
are
both your washer and your clothes.
?
Close
zippers,
make
sure
snag
?
on
hooks and
other clothes.
Pre treat dirt and stains
detergent
help
any small
little
gasket (gray)
and
articles,if any.
Check inside of the drum and
items in it for next wash
?
a
shift dirt.
Check the folds of the flexible
remove
?
by brushing
dissolved in water onto stains like
collars and cuffs to
?
strings to
that these items don't
remove
any left
cycle.
Remove any clothing or items on the flexible
gasket to prevent clothing and the gasket
damages.
11
A dding detergent
Adding detergent and fabric softener
1. The Dispenser Drawer
?
Main wash
only
?PreWash+MainWash
2.
Adding Fabric Softener
?
Do not exceed the maximum fill line.
Close the
Overfilling
dispenser
drawer
can cause
slowly.
early dispensing
of the fabric softener which could stain
clothes.
?
Do not leave the fabric softener in the
detergent drawer for more than
(Fabric softener could harden)
?
Softener will
during
?
automatically
cycle.
2
days.
be added
the last rinse
Do not open the drawer when water is
supplied.
?
Solvents(benzene, etc)
are
not
allowable.
NOTE
Do not pour fabric softener
on the cloths
directly
12
A dding detergent
3. Detergent
Tips
dosage
Full load
The
detergent should be used according to
instruction of the detergent manufacture.
?
If too much detergent
?
result
or cause
Use powder
?
loading
is used,
too many
and this will decrease the
can occur
heavy
load
to
the
according
:
to
manufacturer's recommendation.
Part load
:
3/4 of the normal
amount.
suds
Minimum load
washing
:
1/2 of full load.
motor.
?
detergent only for the front
Detergent is flushed from the dispenser
beginning of the cycle.
at the
washer.
If suds occur too much, pleas
detergent amount.
Detergent usage may
?
the
for water
temperature,
reduce the
need to be
water
adjusted
5. Using the Tablets
1) Open
hardness,
the door and Tablets into the
drum.
size and soil level of the load. For best
results, avoid oversudsing.
4. Water softener
?
A water
softener, such
as
2)
Load the
3)
Close the door.
laundry
into the drum.
Anti limescale
on the
(Clagon)
of detergent in extremely hard water
areas. Dispense according to the amount
specified on the packaging.
First add detergent and then the water
can
be used to cut down
use
softener.
?
Use the
quantity
of
detergent
as
for soft
water.
13
F
unction
Recommended
according
courses
to the
laundry type
Water
Fabric
Program
Color fast
Cotton
Type
Option
Temp.
(Option)
garments
(shirts, night dresses,
pajamas...)and lightly soiled
white cotton(underwear)
60°C
(Cold, 30°C,
40°C, 95°C)
-
-
-
Synthetic Polyamide, Acrylic, Polyester
40°C
(Cold,
30°C, 60°C)
-
-
-
soiled
Lightly
Baby
baby
wear
Time
Delay
Intensive
Pre Wash
Crease Care
Less than
4.0kg
Less than
4.0kg
Less than
3.0kg
Medic Rinse
(40°C, 60°C)
Delicate
Rating
Steam Wash
95°C
Care
Maximum Load
Delicate laundry easily
damaged
40°C
(Cold, 30°C)
Cotton
bedding with filling
duvet, pillow, blanket, sofa
cover with light filling
Duvet
Hand
-
-
-
"Hand wash" marked
Wash
delicate and wool
/Wool
Colored
lightly
Intensive
1
king size
(9 Tog)
Crease Care
Less than
2.0kg
Less than
2.0kg
laundry
which is
laundry
(Cold, 40°C)
soiled fast
Rinse+
-Crease Care
-Medic Rinse
No Choose
Spin
-
Refresh
Cotton mixed,
Polyeter
mixed Dress shirts, blouses
Temperature
:
Intensive
If the
:
laundry
is
follow
heavily
with "Cotton 60°C
Program setting
conformity with EN60456
Pre Wash
:
No Choose
-
Time
Rating
Delay
Steam Default
3 items
Select the water
Always
temperature to the wash cycles.
garment manufacture's care label or instructions when laundering.
soiled "Intensive"
+
Steam Wash
+
option
is effective.
Intensive"
option
for test in accordance
or
in
and IEC60456.
If the
laundry is heavily soiled, "Pre Wash" Cotton is recommended. Pre Wash is available
Cotton, Synthetic and Baby Care program.
in
Crease Care
Medic Rinse
14
Delay
30°C
Quick 30
Water
Time
:
:
If you want to prevent crease, select Crease Care button.
For high effectiveness or more purity in rinse operation you
option. Medic Rinse is default in Baby Care program.
can
choose Medic Rinse
H
ow
to
use
washer
20%
Time Left
1:42
Washing
Temp.
1. Cotton
?
Press the
Power(
?
Press the
Start/Pause(
?
Initial condition
-
Wash
:
Main wash
-
Rinse
:
3 times
)
on.
button to start.
)
button.
Selecting
Press the
?
Select the conditions which you want to
use, by pressing each button.
Power(
)
button to start.
selecting the each conditions, please
refer to the page16~page22
For
Press the Start/Pause button.
3. Language Selection
1600 rpm
[WD-1637(0~9)FD(M)]
?
3
?
?
-Spin:
?
Rinse
2. Manual
automatically
selected upon power
60°C
?
1400 rpm
English is the default language.
Language can be changed only
LCD is
when
Power On and then press the
Time delay and Steam Wash button
[WD-1437(0~9)FD(M)/WM-1437WFD/
WM-1437BFD/WM-1437SFD/
on.
simultaneously for 3 seconds until the
Select a Language menu is displayed.
WM-1437LFD/WM-1437PFD/
WM-1437RFD]
?
Select
1200 rpm
-
Water
temperature
Program
:
:
Language
English
Spanish
Portuguese
[WD-1237(0~9)FD(M)]
-
a
60˚C
Italian
Cotton
?
Rotation of the program dial will cycle
through Spanish, Portuguese, Italian,
German, French, Dutch, Greek and then
back to
English.
15
ow
H
to
use
washer
20%
1:42
Time Left
Washing
Temp.
(1)
(1)
(2)
(3)
(4)
Button
Dial
:
:
(2)
(3)
Power
(5)
(6)
(7)
(8)
Program
Button
:
Start/Pause
Button
:
Time
Delay
(4) (5)
(6)
Button
:
Steam Wash
Button
:
Temperature
Button
:
Rinse
Button
:
Option
60°C
Rinse
3
(7)
(8)
(9) (10)
(9) Button : Child
(10) Button : Tub
(11) Dial : Spin
Power
(11)
Lock
Clean
Program
1. Power
?
Press the Power button to turn power
?
To cancel the Time
button should be
Delay function,
pressed.
on
and off.
the Power
?
2. Initial Program
?
When the Power button is
is
pressed,
the washer
ready
So, if you
cycle
?
?
changing
the
available
according
to the
washing
program, just press
Lamp will light up to indicate selected program.
When Start/Pause button is pressed, the
Cotton program is
want to advance into the
without
are
laundry type.
for Cotton program. And the other initial
conditions as follows.
?
9 programs
-
By turning
the
automatically
Start/Pause button and then the washer will
selected in order of
proceed.
Delicate
Initial program
--
--
"
Cotton
Hand Wash/Wool
Rinse+Spin
selected.
Program dial, the program is
--
Refresh
--
--
--
Synthetic
Duvet
Baby
--
--
Quick 30
Care".
[WD-1637(0~9)FD(M)]
-Cotton
Program / Main
Wash /
Normal Rinse / 1600 rpm / 60˚C
[WD-1437(0~9)FD(M)/WM-1437WFD/WM-1437BFD/
WM-1437SFD/WM-1437LFD/WM-1437PFD/WM-1437RFD]
-Cotton
Program / Main
Wash /
Normal Rinse / 1400 rpm / 60˚C
[WD-1237(0~9)FD(M)]
-Cotton
Program / Main
Wash /
Normal Rinse / 1200 rpm / 60˚C
16
Regarding to the laundry type for each program
Please refer to the page14.
to
ow
H
washer
use
Time
Start/Pause
Delay
Time Delay
Time Delay
Time Left
1. Start
?
This Start/Pause button is used to start
wash
cycle
pause the wash
or
cycle.
-
When in
?
Pause, the power is turned off
after 4 minutes.
Load
at the end of the wash
-
cycle.
in
?
Time Left
Detecting
60°C
Temp.
While the
Turn the
3
many laundries are loaded in the drum. It
will take a few seconds.
Cotton, Synthetic
and
Press the Start/Pause button.
Delay button is pressed, "3:00" is
displayed. The maximum delayed time is
If Time
?
Each pressing of the
delay by one hour.
?
To cancel the time
?
Time
or
?
1:42
Lights
is
to the
selected
According to the
washing time
Rinse
the
condition
of water supply and
temperature, the delayed time and the actual
Washing
60°C
delay, press
'expected time' from the
completion of washing cycle
process (Wash, Rinse, Spin).
Delay
present
4. Door Lock
Time Left
button advances time
Power button.
Baby
Care program.
Temp.
dial to select
hours.
"Detecting" is shown in the display
slowly and detects how
20%
Program
the program you require.
Press Time Delay button and set the
19:00 hours and the minimum time is 3:00
Rinse
the machine rotates
Available in
Delay"
Press Power button.
desired time.
-
7kg
?
laundry and close the door.
detergent and fabric softener
How to set "Time
-
3. Detecting
?
"Time Delay"
Place the
-
NB. The door will not open before 1 to 2
minutes when Pause is selected,
or
?
3:00
cycle will end after
temporary stop of wash cycle is needed,
automatically
?
press
3 hours.
the drawer.
press "Start/Pause" button.
?
The
delay wash time
on the time delay button.
-
2. Pause
If
Time Left
To increase the
Preparing washing before starting
Turn on the water tap.
-
?
3:00
may vary.
3
whenever the door of the washer is
locked.
?
The door
can
be unlocked
Start/Pause button to
?
The door
can
be
by pressing
the
stop the washer.
opened
after
a
short
delay.
17
to
ow
H
use
washer
Steam Wash
Refresh
Refresh
?
Steam
Time Left
Use
on
tough
For
slightly
cycle
wrinkled clothes which have
been stored for
1:42
an
extended time.
It
just makes wrinkled clothes
(Do not load wet clothes).
stained clothes.
?
easy to iron
Wrinkles will be reduced.
How to
1. Turn
use
Refresh
cycle
the washer and select the Refresh program.
2. Load 3 items or less and close the door.
By pressing
the Steam Wash
button, Steam
on
3. Press the Steam Wash button
repeatedly until the
displayed.
Function Can be selected.
desired and correct number of items is
When Steam Function is
Initial
(
)
LED
lights
selected, Steam wash
display
is 2 items
on.
Steam
Time Left
Steam Wash is
?
For
tough
stained
clothes, underwear,
or
0:19
Refresh
baby
clothes.
?
Steam Wash is available with
Press the
Steam Wash button
Cotton, Synthetic,
Baby Care program.
Refresh cycle is fixed Steam wash.
Program
Temperature
60°c (30°c, 40°c, 95°c)
40°c (30°c, 60°c)
95°c (40°c, 60°c)
Cotton
Synthetic
Baby Care
?
?
This
option features upgraded washing
performance with low energy.
Do not load delicates such
easily
as
wool, silk, and
Steam
Time Left
Load
4. Press the Start/Pause button
[Precautionary Notes]
The Refresh
cycle
drying cycles.
-
a
highly
-
-
-
seem
-
there is
no
water inside the
drum(normal condition).
During the steam cycle the strong steam
spray may not be seen through the door
(normal condition).
During the steam operation, a spraying sound
will be heard. (normal condition)
Do not try to open the door while operating.
Steam
can cause severe
Be careful not to touch the door. It
-
-
After
-
clothes from the Refresh
!
operating.
burns.
-
achieved when articles
type. Do
less than 3 dress
cycle they
are
of similar
not overload
shirtes)
CAUTION:
Do not reach into the washer while
Steam
18
are
size and fabric
-
can cause severe
removing
Best result
-
CAUTION:
Steam
be very hot.
may feel slightly damp wait at least 10 minutes
before putting the clothes on.
burns.
Do not reach into the washer while
can
Do not open the door while operating.
Steam can cause severe burns.
-
(Load
!
or
fibers, this cycle
clothing.
Remove stains from clothing before using the
Refresh cycle to prevent permanently setting the
stains by high heat.
Be sure that the faucet is open. This cycle uses a
little water to produce steam.
concentrated and
efficient.
It may
washing
is not recommended for 100% cotton
-
Steam wash is
is not like other
Due to the characteristic of cotton
-
discolored clothes.
NOTE:
-
0:19
3 items.
can cause severe
Keep pets
burns.
away from the washer.
operating.
ow
H
to
use
washer
Water Temp.
?
By pressing
Rinse
the
Temp.
?
button, the water
temperature can be
the Rinse
the Rinse
button,
type
can
be selected.
selected.
-
By pressing
Cold
-30˚C/40˚C/60˚C/95˚C
?
-
Water
temperature
below
according
Baby
Care
40˚C
--
can
be selected
as
to the program.
1. Normal
60˚C
--
95°C
?
-
Cotton
Cotton, Synthetic, Baby
Care performs 3
Rinses
Cold--30˚C--40˚C--60˚C--95˚C
?
-
Synthetic
Cold
-
--
30˚C
--
40˚C
--
Hand
Wash/Wool, Quick 30, Delicate,
Duvet performs 2 Rinses
60˚C
Delicate & Quick 30 & Hand Wash/Wool
& Duvet
Cold
--
2. Rinse + & Rinse ++
30˚C
--
40˚C
?
The
required temperature lamp
identification.
For the
to the
more
detailed
will
Used to additional
in
light up for
?
information, please refer
rinse, which may assist
traces of
removing
By selecting
Rinse +
detergent
or
Rinse ++
residue.
function,
the Rinse Time and the Rinse water
page14.
are
increased.
3. Rinse Hold
?
Is selected
by pressing
repeatedly.
This function leaves clothes in
the
washer; suspended in the
rinse without
?
To
the Rinse button
entering
proceed through
into
water after a
spin.
to a drain or
spin, once
completed using to
the required program.
the rinse hold function is
program dial scroll to
The required lamp
identification.
will
light up for
19
H
ow
to
use
washer
Child lock
Option
If you choose to lock the buttons on the
control assembly to prevent tampering, this
each the button, each function
will be selected.
By pressing
function may be selected.
?
1. Intensive
Child lock
can be set by pressing and
holding the Crease Care and Medic Rinse
button simultaneously.
(About three seconds)
If the laundry is heavily soiled "Intensive"
option is effective.
By selecting the Intensive option, the wash
time may be extended, depending on the
?
?
20%
Time Left
Child Lock is
Temp.
1:42
on.
60°C
Rinse
3
program selected.
To
?
this option, press the intensive button
before the wash program is started.
use
once
2. Pre Wash
Use this
?
option
?
?
for load that need
pretreatment. Add
To deactivate Child lock
system, press and
hold the Crease Care and Medic Rinse
simultaneously again.
(About three seconds)
When
using Pre Wash option, do not use
liquid detergent in the main wash
comportment. Use powder for the main
20%
Time Left
1:42
Child Lock is off.
wash.
Available in
?
are
button
16 minutes pre wash and
drain.
-
When child lock is set, all buttons
inoperable, except Power button
Temp.
60°C
Rinse
3
Cotton, Synthetic and Baby Care
program.
?
To
change
to the desired program, whilst in
child lock mode.
3. Crease Care
If you want to prevent crease, select this
button with spin speed.
?
4. Medic Rinse
1. Press and hold both Crease Care and
Medic Rinse button
(About
three
together
seconds)
once
again.
2. Press the Start/Pause button.
3. Select the desired program and press the
Start/Pause button again.
For high effectiveness or more purity in rinse
operation you can choose Medic Rinse option.
Available in Cotton, Synthetic and Baby Care
?
?
program.
Medic Rinse is default in
Baby Care program.
required temperature lamp will light up for
identification.
?
The
20
?
The child lock
is
errors occur.
power is off.
be set at any time and it
canceled when operational
can
automatically
Also Child lock works when
to
ow
H
use
washer
Spin
Tub Clean
Tub Clean
course can
and
be set
[WD-1237(0~9)FD(M)]
by pressing
holding
simultaneously.
is set, display
"Tub Clean", and all buttons are inoperable.
course
Time Left
1:32
Tub Clean
-
-
TUB CLEAN is
How to
use
the Tub Clean
2.
Open
the
limescale
dispenser drawer and add Anti
(Calgon) to the Main wash
detergent to the
detergent compartments. Excessive
suds may
washer.
3. Close the
generate and leak from the
dispenser
drawer
then "Tub Clean" is
displayed
in LCD.
5. Press the Start/Pause button to start.
6. After the
is
leave the door
cycle complete,
dry around the washer door
opening, flexible gasket and door glass.
open to
!
CAUTION: If there is
spin speed
Spin speed
is available
Cotton & Quick 30 &
Rinse+Spin
NoSpin--400--600--800--1000--1100--1200
Synthetic & Hand Wash/Wool & Duvet &
Baby Care
NoSpin--400--600--800--1000
Delicate
-
-
-
Cotton & Quick 30 &
Rinse+Spin
NoSpin--400--600--800--1000--1200--1400
Synthetic & Hand Wash/Wool & Duvet &
Baby Care
NoSpin--400--600--800--1000
Delicate
NoSpin--400--600--800
WD-1637(0~9)FD(M)
-
-
-
Cotton & Quick 30 &
Rinse+Spin
NoSpin--400--600--800--1000--1200--1600
Synthetic & Hand Wash/Wool & Duvet &
Baby Care
NoSpin--400--600--800--1000
Delicate
NoSpin--400--600--800
2. No spin
?
If "No Spin" is selected,
draining water.
3. Spin
the washer
stops after
Only
2. Set the desired
open for too
3. Press the Start/Pause button.
long.
be chosen.
according to the program as follows.
small child, be
careful not to leave the door
a
can
WM-1437SFD/WM-1437LFD/WM-1437PFD/WM-1437RFD
slowly.
4. Power On and then press and hold
Intensive and Pre Wash button for 3 seconds.
the
WD-1437(0~9)FD(M)/WM-1437WFD/WM-1437BFD/
compartment.
NOTE: Do not add any
Spin dial,
NoSpin--400--600--800
cycle:
1. Remove any clothing or items from the
washer and close the door.
the
WD-1237(0~9)FD(M)
-
special cycle to clean the
inside of the washer. This cycle uses higher
water level with higher spin speed. Perform
this cycle regularly.
By turning
1. Spin selection
?
20%
[WD-1637(0~9)FD(M)]
WM-1437LFD/WM-1437PFD/WM-1437RFD]
?
When Tub Clean
[WD-1437(0~9)FD(M)/WM-1437WFD/
WM-1437BFD/WM-1437SFD/
Intensive and Pre Wash button
1. Press the Power button.
The
spin speed by turnning spin
required lamp will light up for identification.
dial.
21
ow
H
to
washer
use
Display
3. Completion of
?
20%
1:42
Time Left
60°C
Rinse
1. Special function
?
washing cycle is completed,
cycle is displayed on the
display".
During washing cycle, the remaining
washing time is displayed.
?
Recommended program
display
"
-
When time
the
delay is selected, it shows
remaining times to finish the selected
-
-
program.
-
2. Self
?
diagnose display
If the washer encounters
operation,
displayed.
"
"
"
"
"
"
"
"
"
"
"
"
"
"
fault
-
during
-
the associated fault will be
-
-
Water pressure
:
a
sensing
:
Problem of
:
Door is not closed
overfilling
error
?
water
?
PF
around 2 hours and 37 minutes
Hand Wash/Wool
Duvet
:
:
around 57 minutes
around 30 minutes
around 1 hour and 12 minutes
:
Rinse+Spin
Refresh
:
:
around 23 minutes
around 19 minutes
The
washing time may vary by the
laundry, water pressure, water
temperature and other washing conditions.
If
an
unbalanced load is detected
or
if the
Over load in motor
:
Water inlet trouble
(Max. increasing
:
Drainage
:
Unbalanced load
trouble
Water
"
temperature trouble
:
Water leaks
:
The washer
"
experienced
removing
time is 45
Est. Time
a
power failure.
If these error letters are displayed, please
refer to the troubleshooting page27 and
follow the guide.
22
:
around 1 hour and 12 minutes
:
Quick 30
suds
?
"
Care
Delicate
around 1 hour and 24 minutes
:
:
"
AE
around 1 hour and 51 minutes
:
Synthetic
Baby
manufacturer.
program operates, the
wash time may be extended.
:
"
Cotton
by
amount of
?
"
"Multi
?
-
?
"
End of
4. Time left
3
When Child lock is selected, the
lamp is on.
"
When
"
Washing
Temp.
washing
minutes.)
Remaining
This
display shows the estimated time
remaining in the cycle when operating.
This washer automatically detects the
wash load (weight) and optimizes the
washing time. After detecting, the display
will show the adjusted time remaining.
Status Indicator
?
It shows
elapsed time
operating.
washer is
of the
cycle
the
M
aintenance
Before
cleaning
the washer
interior, unplug the electrical power cord
to avoid electrical
shock to avoid electrical shock hazards.
When
disposing
the door lock to
of the appliance, cut off the mains cable, and destroy the plug Disable
prevent young children being trapped inside.
The water inlet filter
"
-"
error
detergent
-
message will blink
the control
panel
when water does not enter the
drawer.
If water is very hard
become
on
clogged.
a good
It is therefore
or
contains traces of lime
deposit,
the water inlet filter may
idea to clean it from time to time.
1.
Turn off the water
2.
Unscrew the water inlet hose.
3.
Clean the filter
tap.
using
a
hard bristle
brush.
4. Tighten up
the inlet hose.
23
M
aintenance
The drain pump filter
The drain filter collects threads and small
Check
!
regularly
CAUTION
that the filter is clean to
First drain
using
Be careful when
draining
Allow the water to cool down before
emptying
or
opening
laundry.
running of your
machine.
objects.
or
if the water is hot.
cleaning
the door in
a
the drain pump,
an
1. Open
100
left in the
smooth
the drain hose and then open the pump filter to
whatever any threads
remove
emergency
objects
ensure
carrying
out
emergency.
the lower
cover
cap
( ) by using
coin.
Drain
plug ( )
to
pull
out the hose.
1
2. Unplug
the drain
plug ( ), allowing
water to flow out. At this time
3
vessel to
water
prevent
the
use a
flowing
on
to the
floor. When water does not flow any
more, turn the pump filter
2
3.
4.
open to
Remove out any
foreign
material from
the pump filter
( ).
After
turn the pump filter
cleaning,
clockwise and insert the drain
3
the
original place.
cap.
2
24
( )
the left.
( )
plug ( )to
close the lower
cover
aintenance
M
Dispenser drawer
After
a
while
detergents
and fabric softeners leave
deposit
?
It should be cleaned from time to time with
a
?
If necessary it
from the machine
can
be removed
downward and
?
To facilitate
by pulling
cleaning, the upper part
Detergent can
?
The
?
with
occasionally
washing
If you live in
seen
a
of the fabric softener
also accumulate inside the
without
cycle
water.
by pressing
the catch
compartment
can
be removed.
recess
Once you have finished
rinse
running
in the drawer.
it out.
The drawer
be cleaned
completely
jet
of
a
recess
cleaning, replace
the drawer and
run a
laundry.
drum
hard water area, limescale may
and thus not
which should
old toothbrush.
an
easily
continuously
build up in
places
where it cannot be
removed.
Over time the build up of scale
clogs appliances,
and if it is not
kept
in check these may have to be
replaced.
?
Although the washing drum is made of Stainless steel, specks of rust
articles (paper clips, safety pins) which have been left in the drum.
?
The
?
washing
If you
use
can
be caused
by
small metal
drum should be cleaned from time to time.
descaling agents, dyes
or
bleaches, make
sure
they
are
suitable for
washing
machine
use.
Descaler may contain chemicals that may
Remove any
Never
use
spots
with
a
stainless steel
damage part
of your
washing
machine.
cleaning agent.
steel wool.
25
aintenance
M
The water circulation nozzle & Steam nozzle
?
Clean the water circulation nozzle and Steam
nozzle, if clogged.
Cleaning your washer
1. Exterior
of your washer
can
extend its life.
The outside of the machine
can
be cleaned with
Proper
care
household
water and a neutral non abrasive
detergent.
off any
Immediately wipe
not to hit surface with
Try
warm
IMPORTANT: Do not
spills. Wipe
with
damp
cloth.
sharp objects.
methylated spirits,
use
diluents
or
similar
products.
2. Interior
Dry
around the washer door
Run washer
through
Repeat process
a
deposits using only
If the washer is stored in
1. Turn off water
an area
cleaners labeled
as
safe for
washing
where
freezing may
to
occur or
prevent damage
moved in
freezing
to the washer:
supply tap.
2. Disconnect hoses from water
4. Add
glass.
instructions
temperatures, follow these instructions
Plug
and door
if necessary.
Winterizing
3.
gasket
hot water.
complete cycle using
Remove hard water
machine.
NOTE
flexible
opening,
electrical cord into
1gallon(3.8L)
a
supply
and drain water from hoses.
properly grounded
of nontoxic recreational
electrical outlet.
vehicle(RV)
antifreeze into
an
empty wash drum.
Close the door.
5. Set
spin cycle
and let washer
spin
Not all of the RV antifreeze will be
6.
Unplug
electrical power
7. Remove
9. To
remove
through
26
a
an
expelled.
cord, dry the drum interior, and close the door.
dispenser drawer,
8. Store washer in
for 1minute to drain out all water.
drain and
dry
excessive water from the
upright position.
antifreeze from washer after
storage,
complete cycle using detergent.
run
empty washer
Do not add wash load.
compartments.
T roubleshooting guide
This
washing machine is equipped with automatic safety functions
diagnose faults at an early stage and react appropriately.
When the machine does not function properly or does not function
following points before you contact your service provider.
all, check the
at
Possible Cause
Symptom
Rattling and
clanking noise
which detect and
?
Solution
Foreign objects such as coins
safety pins maybe in drum or
or
Stop
washer and check drum
and drain filter.
If noise continues after washer
pump.
is restarted, call your authorized
service centre.
Thumping
sound
?
Heavy wash loads
thumping sound.
a
may produce
This is usually
normal.
Vibrating
noise
?
?
redistribute wash load.
Have all the transit bolts and
packing
If not removed
been removed?
Are all the feet
the
If sound continues, washer is
out of balance. Stop and
probably
during
installation, refer
resting firmly
on
for
removing
to Installation
Wash load may be
distributed
ground?
in drum.
guide
transit bolts.
Stop
unevenly
washer and
rearrange wash load.
Water leaks.
?
Fill hoses
at
?
tap
or
or
drain hose
are
loose
Check and
tighten
hose connections.
washer.
House drain
pipes
are
clogged.
Unclog
drain
pipe.
Contact
plumber
if necessary.
Too much
detergent or unsuitable
detergent may cause excessive
foaming which may result in water
Oversudsing
leaks.
Water does not enter
washer
or
?
it enters
slowly
Water
supply
is not
adequate
in
Check another
tap in the house.
area.
?
Water
?
Water inlet
?
The filter of the inlet
supply tap
completely open.
is not
hose(s)
are
Fully
kinked.
hose(s)
are
open tap.
Straighten hose(s).
Check the filter of the inlet
clogged.
Water in the washer
does not drain
drains
slowly.
?
Drain hose is kinked
?
The drain filter is
or
clogged.
or
clogged.
Clean and
straighten
hose(s).
the drain hose.
Clean the drain filter.
27
T roubleshooting guide
Possible Cause
Symptom
Washer does not start
?
Electrical power cord may not
plugged in or connection
be
Solution
Make
plug fits tightly
sure
in wall
outlet.
may be loose.
?
House fuse blown, circuit
Reset circuit breaker
breaker
Do not increase fuse
tripped,
or a
power
outage has occurred.
If
problem
is
it corrected
?
Water
supply tap
is not turned
Turn
on
a
by
water
replace fuse.
capacity.
or
circuit overload, have
a qualified electrician.
supply tap.
on.
Washer won't
spin
Check that the door is
shut.
firmly
Close the door and press the
Start/Pause button. After pressing
the Start/Pause button, it may take
a few moments before the washer
begins to spin. The door must
before spin can be achieved.
Door does not open
Once started, the door
opened for safety
Wait
one or
can
lock
not be
reasons.
two minutes before
opening the door to give the electric
locking mechanism time to release.
Wash
cycle
delayed
time
The
washing time may vary by the
laundry, water
amount of
pressure, water temperature and
other using conditions.
If the imbalance is detected
suds
or
if the
program works, the
wash time shall be increased.
28
removing
T roubleshooting guide
Possible Cause
Symptom
?
Water
supply is
not
adequate in
Solution
<Fig
1>
Check another
tap in the house.
area
?
?
?
?
Water
supply taps are not
completely open.
Water inlet hose(s) are kinked.
The filter of the inlet hose(s) are
clogged.
If water leakage occurred in the inlet hose,
indicator " " will be changed red color.
?
Drain hose is kinked
?
The drain filter is
clogged.
clogged.
or
Fully open tap.
Straighten hose(s).
Check the filter of the inlet
Clean and
straighten
the drain hose.
Clean the drain filter.
For
more
detailed
information,
please refer to "The drain
on page22
?
Load is too small.
Add 1
?
Load is out of balance.
balance the load.
?
The
Rearrange
spinning
appliance has
an
unbalance detection
and correction
system. If individual heavy
articles are loaded (ex. bath mat, both robe,
etc.), this system may stop spinning or even
?
or
pump filter"
2 similar items to
help
load to allow proper
interrupt the spin cycle altogether.
If the laundry is still too wet at the end of the
cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
?
Is the door
opened or not
completely
closed?
Close the door
If "Door
Water overfills due to the
faulty water
valve.
completely.
Open"is not released,
call for
service.
Unplug the
?
hose(s).
power plug and call for service.
Close the water
tap.
Unplug the
power plug.
Call for service.
?
Water level
?
Over load in motor.
?
Water leaks
?
The washer
sensor
has malfunctioned.
Call for service.
experienced a power failure.
Restart the
cycle.
29
erms
T
of Warranty
of your old
Disposal
appliance
1. When this crossed-out wheeled bin
product
it
means
the
product
symbol is attached to
by the European
a
is covered
Directive 2002/96/EC.
2. All electrical and electronic
products should be disposed of
municipal waste stream via designated
appointed by the government or the local
from the
separately
collection facilities
authorities.
3. The correct
disposal of your old appliance will help prevent
potential negative consequences for the environment and
human health.
4. For
more detailed information about disposal of your old
appliance, please contact your city office, waste disposal
service or the shop where you purchased the product.
What Is Not Covered:
?
Service
?
If the
?
If the fault is caused
by accident, neglect,
If the fault is caused
by
?
trips
to your home to teach you how to
product
is connected to any
voltage
use
the
product.
other than that shown
misuse
or
on
the
rating plate.
Act of God.
factors other than normal domestic
use or use
in accordance
with the owner's manual.
?
Provide instruction
?
If the fault is caused
?
Noise
or
sound,
on use
of
by pests
product
for
or
change
example,
vibration that is considered normal for
or
the installation for
Correcting
?
Normal maintenance which recommended
?
Removal of
inlet hose
fuses in
Correction of unauthorized
?
Incidental
or
wiring
:
example
water drain
sound, spin
by
the
or
of drain.
product, adjustment
the owner's manual.
correct house
the pump and
plumbing.
repairs.
consequential damage
appliance.
or
product
(Example
example, levelling
correct house
Replace
?
If this
set-up of the product.
cockroaches etc..
foreign objects / substances from the machine, including
filter for example, grit, nails, bra wires, buttons etc.
?
?
the
or
warming beeps.
?
with this
rats
to
personal property
caused
by possible
is used for commercial purpose, it is not warranted.
Public
places
such
as
public bathroom, lodging house, training
center, dormitory)
If the product is installed outside the normal service area, any cost of
transportation involved in the repair of the product, or the replacement
defective part, shall be borne by the owner.
30
of
a
defects
Download PDF