LG | GC-161SW.CSWQLGU | LG GC-161SW.CSWQLGU Owner’s Manual

P/NO.3828JS8023F
FRIDGE-LARDER
User's Guide
Please read this User's Guide
before
operating
and
keep
reference at all times.
it
carefully
handy for
Electrical Connections
(In the UK Only)
The wires in this mains lead
Important
with the
following
are
coloured in accordance
code:
GREEN AND YELLOW:EARTH
BLUE:NEUTRAL
BROWN:LIVE
This
Green and Yellow
Brown
appliance
must be earthed
(Earth)
E
(Live)
Fuse
L
Blue
(Neutral)
N
Cord
grip
As the colours of the wires in the mains lead of this
apparatus may
identifying
not
correspond
with the coloured
the terminals in your
plug, proceed
as
markings
follows:
The wire which is coloured Green and Yellow must be
connected to the terminal in the
the letter E
or
by
the earth
plug which is marked with
symbol( ) or coloured Green or
Green and Yellow.
The wire which is coloured Blue must be connected to the
terminal which is marked with the letter N
or
coloured
Black.
The wire which is coloured Brown must be connected to
the terminal which is marked with the letter L
or
coloured
Red.
If
a
13
fuse.
2
amp(BS 1363) plug
is
used, fit
a
13 amp BS 1362
Table of Contents
Important safety
Introduction
Instruction
Disposal of the old appliance
packing of new appliance
Installation
Operation
food
Location
8
Installation with/without top table
9
Electrical Connection
9
Door Handle
9
Starting
10
the
Temperature
Off
food
Storing
10
10
11
storage
Care and
maintenance
Defrosting
12
Cleaning
13
General Information
14
Lamp Replacing
14
for
saving Energy
15
shooting
16
How to Reverse the Door
17
Tips
Trouble
6
7
Switching
on
&
Identification of Parts
Controlling
Suggestion
4
Trouble
shooting
To Reverse the
Doors
3
Introduction
Important Safety Instruction
The
supply plug of the refrigerator-larder should be
placed in easy accessible position for quick disconnection
Accessibility of
Supply Plug
in emergency.
Supply Cord
Replacement
If the
supply
cord is
manufacturer
damaged,
it must be
its service agent or
person in order to avoid a hazard.
This
Precaution
or
must be
fridge-larder
a
replaced by the
similarly qualified
properly
installed and
located in accordance with the Installation
Instruction before it is used.
unplug your fridge-larder by pulling on the
power cord. Always grip plug firmly and pull straight
Never
out from the outlet.
moving your appliance away from the wall,
be careful not to roll over or damage the power
cord.
When
Pull out the power
plug prior
to
cleaning
the
fridge-
larder
Never
damage, severely bend, pull out, or twist the
damage may cause
power cord because power cord
fire or electronic shock.
Don't
If
use an
possible,
connect the
fridge-larder
to its
a
own
individual electrical outlet to prevent it and other
appliances or household lights from causing an overload.
extension cord
4
Introduction
w
Danger
Risk of child entrapment.
Before you throw away your old
refrigerator
:
Take off the doors.
Leave the shelves in
place
so
that children may not
easily
climb inside.
In the event of
Grounding
(Earthing)
electric short circuit,
grounding (earthing)
by providing an escape
wire for the electric current. In order to prevent possible
electric shock, this appliance must be grounded. Improper
use of the grounding plug can result in an electric shock.
an
reduces the risk of electric shock
Consult
qualified electrician or service person if the
grounding instructions are not completely understood,
you have doubts on whether the appliance is properly
grounded.
w
Warning
a
or
if
w Keep ventilation openings, in the appliance enclosure
or in the built-in structure, clear of obstruction.
w Do not
use
mechanical devices
or
other
means
accelerate the
defrosting process, other than
recommended by the manufacturer.
w Do not
damage the refrigerant
w Do not
use
electrical
appliances
to
those
circuit.
inside the food storage
are of the
compartments of the appliance, unless they
type recommended by the manufacturer.
w The
refrigerant and insulation blowing gas used
appliance require special disposal procedures.
At disposal, please consult with service agent or
similarly qualified person.
5
in the
a
Introduction
Disposal of the old appliance
packing of new appliance
Disposal
&
The old
appliance whose life has expired should be
destroyed in order to make it safe prior to disposal. Take
out power plugs, separate connection wires and remove
or destroy all springs, latches or bolting, to prevent
children from being trapped during play.
of the old
appliance
For environmental
protection, old refrigerators should be
disposed
by professional disposition agency. If you
have any question, please consult with the local sale
agency or local authority.
off
a
All
packing materials used
environment-friendly.
Disposal of
packing of new
appliance
material
Matters
concerning
PE
:
Polyethylene
PS
:
Formed
objects made
CFC-FREE polystyrene
PP
:
Strapping tape
This
Take back offer
for this
appliance
--
Foil
are as
are
follows:
pocket
or
for
packing
of foamed
made of
contains fluid
appliance
polypropylene
(refrigerant, lubricant)
made of parts and materials which
are
and is
reusable and/or
recyclable.
All the
important
materials should be sent to the
collection center of waste material and
after rework
(recycling).
with the local agency.
6
For take
can
be reused
back, please
contact
Introduction
Identification of Parts
NOTE
This is
a
subject
7
basic model. The
to
change.
shape
of
refrigerator
is
Installation
Location
This
is suitable for
appliance
using
at ambient
temperature between +16°C and +32°C. If the ambient
temperature drops below +16°C, it is possible that the
freezing foods in the freezer compartment are thawed
because the temperature of the freezer gets warm.
We recommend that the
refrigerator be installed at a dry
place. Make sure that the appliance is
direct sunlight or placed in vicinity of a
and well ventilated
not
exposed
heat
as
make
impossible,
or
to
such
source
at least the
stove, heaters, radiator. If it is
use
of
following
an
adequate plate (not asbestos)
minimum distance must be
secured.
from
a
Gas
from oil
or
electric cooker
coal-fired stoves
or
from another
:
:
3cm
30cm
refrigerating appliance
:
2cm
NOTE
Place
even,
on a
flat and firm
adjust
at the front
the feet
edge
If the front is
can
8
close
flooring. If the floor is not
by using the leveling screw
of the cabinet.
slightly higher
easily.
more
than the rear, the door
Installation
Installation with/
without top table
Check that the hot air caused to
warm
air from the
rear
of the
appliance circulates without obstruction. If not, it
could cause the output of the refrigerating unit to
increase and this will result in
a higher rate of energy
confirm
that ventilation grill is
consumption. Therefore,
never covered or blocked.
1. when
installing with top
table(free standing),
push the refrigerator
until the air
circulating hole of top
nearly reaches
table
the wall.
2. when
installing without
top table, align the door
front edge to the front edge
of
kitchen furniture.
How to Remove
Top Table
1. Unscrew 2 bolts at
the
rear
2
of top table.
2. Hold the
rear
table and
forwards
top table
of top
push
by lifting
slightly.
1
up
Electrical connection
This
appliance
should be connected to the mains AC
220~240V 50 Hz. You must connect this
,
appliance only
grounding complying with the
only an approved expert should
to the power socket with
related
regulations and
appliance.
install this
Door Handle
In
case
of
installing
enclosed with it in
9
the door handle, refer to
a
product package.
a
figure
Operation
Starting
Before
it on, leave the appliance standing for
that the circulation of the refrigerant
switching
at least 2
hours,
stabilizes and
so
operating problems
no
occur.
Turn the
temperature control dial from the position "0".
The refrigerating process begins and the lamp inside
refrigerator
on
goes
when the door is
Controlling
opened.
the temperature
We recommend to set the dial "4" for normal.
Too
warm :
Turning
the
temperature control
dial clockwise will set
colder
setting
(higher number
setting).
to
Too cool
:
a
Turning
the
temperature control
dial counterclockwise
will set to
a warmer
setting
(lower number setting).
The temperature
temperature, the
setting depends on ambient
quantity of foods, how often the door
is opened. So the temperature setting should be checked
by using an appropriate thermometer and following the
instructions
on
it.
Switching off
Turn the
temperature control dial counterclockwise until
refrigerating process stops and the lamp
set to "0". The
inside
10
refrigerator
goes off.
Suggestion
on
food storage
Storing food
Opening the door often
long time, increases the
or
keeping
the door
opened
a
inside temperature. This causes
the storage life and flavor of the foods to reduce, and
increases the energy consumption.
food
Arranging
-
Store the food
products
that
give
off odor in closed
containers and wrap.
-
Use aluminum
containers
-
Allow
warm
placing
-
as
foil, plastic foil and metal
the
packing
foods to cool down
inside the
or
glass
material for foods.
sufficiently
before
appliance.
alcoholic
Keep high-proof
upright position.
beverages
in
airtight
bottles
and
-
Do not store the
etc) which
are
<Refer to the
products (melon, banana, pineapple
likely to go bad at low temperature.
Figure
of page 7>
Bread, ready-cooked meals.
Meat, Sausages, Slice products.
Vegetables, Fruit, Salad produce.
Butter, Cheese.
Small glasses or bottles, cans, spices.
Eggs.
Large beverage bottles.
Make
11
sure
the door is closed
properly.
Care and Maintenance
Defrosting
Defrosting
the
fridge compartment
When the
refrigerator is working, frost is formed at the
fridge compartment and melts
when
the compressor stops. The thawed
automatically
water is collected in the discharge gutter and evaporates
by heat of the compressor.
rear
NOTE
wall of the
Never
place
electrical devices in the
for defrost. Take
for
care
when
assisting defrosting. These sprays
substances containing explosive gas,
synthesis or human health.
12
refrigerator
using defrosting
sprays
include
or
harmful for
Care and Maintenance
Cleaning
w
Always remove plugs
cleaning.
Warning
Do not
or
Switch off
before
supply
sharp objects (such as knife, screwdriver)
refrigerant circuit resulting in
use
which could break
environmental and health risks.
use steam cleaner or steam pressure cleaner since
hot steam may damage refrigerator surface and electrical
devices. Never use sand, abrasive detergent, acid or
Never
chemical solvent.
?
The most
appropriate
compartment is
?
a
time for
time after
Care should be taken that
cleaning
defrosting.
cleaning
of the freezer
water does not
enter the inside of the thermostat Enclosure
?
Clean
refrigerator including
Regularly clean the
refrigerator using a
heat
inside and
cause
Any damage
leading
use
exchanger
smooth brush
of dusts and residues. Do not
commercial
on
so
the
rear
side of
that accumulations
disrupt expansion from
consumption.
to the heat
exchanger or other events
refrigerant to the
environment, should be avoided because of
13
the
increased energy
to the exposure of the
potential
lamp.
inside devices with clothes
lukewarm water. You may
detergent for tableware.
or
or
environment and health risks.
Care and Maintenance
General information
Going
When you plan to be away for an extended period,
remove all food, disconnect the power cord, clean the
interior thoroughly, and leave the door OPEN to prevent
away
odor formation.
Most power failures are corrected in an hour or two and
will not affect your refrigerator temperatures. However,
you should minimize the number of door openings while
Power failure
the power is OFF.
If you
Remove all items inside the
move
all loose items. To avoid
refrigerator or securely fasten
damaging the leveling screw,
turn them all the way into the base.
Anti-condensation
?
The Anti-condensation
pipe
is
Anti-Condensation
installed around the front side
pipe
of
fridge-larder
dewing.
?
Especially
to
Pipe
prevent
after installation
or
when ambient temperature is
high, the fridge-larder may
feel hot, which is
quite
normal.
Lamp Replacing
Unplug
the power cord from the AC outlet.
1. Take the shelves out
to make
access
easier.
3 2
4
5
2. Hold the
lamp,
softly from
cover
take it out
1
0
6 7
the thermostat
enclosure with
twisting
up and down.
3. Turn the
lamp counterclockwise, and replace it
(max 15W, 220~240V)
4. Assemble in
reverse
Replacement
original.
14
order of
disassembly.
same specification
bulb must be the
as
Care and Maintenance
Tips for saving Energy
-
After
on
-
moving
again.
Do not
place
the
appliance,
the
appliance
sources.
Place the
appliance
near
radiator, stove,
If ambient temperature is
the compressor will run longer.
-
and heat
allow 2 hours to turn
room.
-
-
on a
cool and well ventilated
Do not expose to direct
Do not
keep
the door
high,
opened
sunlight.
too
long.
Do not place warm food and beverages in
appliance. Please cool down first otherwise
the steam from hot foodstuffs would contribute
to the
icing up of the evaporator unit; and the
cooling period should be as short as possible, for
health and hygiene reasons.
-
Do not set the
temperature of appliance lower than
needed.
-
Replace magnetic door gasket
properly functioning.
not
15
of the door if it is
Trouble
Before
for
calling
service,
Shooting
check this list.
It may save you both time and expense.
This list includes common occurrences that
the result of defective
this
workmanship
or
are
not
materials in
appliance.
Possible Causes
Problem
Fridge-Larder
operate
?
Power
plug
may be
unplugged
from the electric
outlet.
does not
Plug
?
it in
securely.
House fuse has blown
or
circuit breaker has
tripped.
Check and/or
?
or
Rattling
or
?
Abnormal Noise
lights.
The floor on which the fridge-larder is installed
may be uneven or the fridge-larder may be
unstable.
Make it
?
fuse and reset circuit breaker.
Power cut.
Check house
Vibration
replace
even
by rotating
the
leveling
Unnecessary objects placed
screw.
in the back side of the
fridge-larder.
Temperature of foods
inside refrigerator is
not cold enough
?
The inner
?
Too
frequent
There is
a
or
heat
too
long
large quantity of food
fridge compartment.
A
light
does not work
?
temperature
inside the refrigerator
16
on
setting
the
"O".
Lamp Replacing"
The temperature controller is
high figure.
is too cold
openings.
Fridge-larder.
was placed inside
The temperature controller is
The bulb is defective.
Refer to "Section of
The
door
source near
setting
to
extremely
Trouble
Shooting
Possible Causes
Problem
Fridge
has odor
Moisture forms
on
?
Foods with strong odors should be
covered or wrapped
?
Check for
?
Interior needs
?
Refer to
?
This
cabinet surface
Interior
light
does
?
not work
?
17
tightly
spoiled food
cleaning
"Cleaning Section"
phenomenon is likely to
Wipe it with a dry towel
occur
in
No power at outlet.
Light lamp
needs
Refer to the
Lamp Replacement
replacing.
section.
a
wet space.
To Reverse the Doors
How to Reverse the Door
Your
refrigerator
is
designed
with
a
reversible door,
so
you may open from either left or right. It is best to
reposition the door hinge as necessary at the outset since
it is inconvenient to do so later.
change
the door
below and
proceed
To
Precaution
1. First
unplug
the
hinge please
as
refer to the
appliance.
2. Remove foods and accessories like shelves
which are not fixed in the refrigerator.
3.
Carefully lay the appliance on
material to avoid the damage
4. Use '+' driver
or
spanner to fix
1. Unscrew the 2xBOLTS
2. Remove the LEG
3.
Gently pull
diagram
follows.
,
then
or
trays
cushion like packing
of refrigeration circuit.
a
or remove
remove
the
the bolts.
hinge (L) .
.
the door downwards to
remove
it.
4. Before
refitting the door, swap the
it out from its current location and
Hinge Cap
by pulling
repositioning it on the
other side of the door. Care should be taken not to damage
the adjacent surfaces when removing the Hinge Cap.
5. Unscrew the
opposite
4
18
Upper Hinge pin (U)
side hole.
4
and
screw
it into the
To Reverse the Doors
How to Reverse the Door
6. After
refitting the door, fix the Lower Hinge(L)
opposite side by using 2xBOLTS.
7. Fix the
8.
NOTE
in the
Leg.
Carefully place the appliance in an upright position.
Adjust the Leveling screw to make sure the appliance
is steady and check that the door opens and closes
properly.
In case of applying Reversible door, when you close
the door with excessive force, there could be the case
that the door doesn't close because of Reaction
force. Please ascertain if the door closes
Door
19
handle(Option)
properly.
Download PDF

advertising