LG | GC-F399BVQA.CSWQECZ | LG GC-F399BVQA.CSWQECZ Owner’s Manual

Introduction
Important Safety Instruction
Water tank can fill with potable
water only.
Do not install the fridge-freezer in the wet place or
the place which water or rain splashes.
Deterioration of insulation of electric
parts may cause electric leakage.
Do not use or store inflammable materials ether,
benzene, alcohol, medicine, LP gas, spray or
cosmetics near or in the fridge-freezer.
It may cause explosion or fire.
Do not place the lit candle within the fridge-freezer
to deodorize.
It may cause explosion or fire.
Do not store the medicine or the academic materials
at the fridge-freezer.
When the material with the strict
temperature control is stored, it may be
deteriorated or it may make an
unexpected reaction to cause any risk.
Do not use the combustible spray near the fridgefreezer.
It may cause fire.
7
18
19
20
21
Operation
Water Dispenser
Features
Install
• Please assemble the VALVE ASSEMBLY after correctly
adjusting it with a DOOR HOLE.
22
23
24
25
26
27
28
29
To Reverse the Doors
Your fridge-freezer is designed with reversible doors,so that they may open from either
the left or right hand side to suit your kitchen design.
Precaution
1. Before reversing the door, first of all,you should take out food and accessories like
shelves or trays which are not fixed in the fridge-freezer.
2. Use Torque Wrench or Spanner to fix or remove the bolt.
3. Do not lay the fridge-freezer down.This will cause problems.
4. Be careful not to drop the doors in disassembling or assenbling.
3
2 2
How to Reverse the Door
1.To separate the door handle 1 of the left side, separate the
door cap and unscrew the screw in counterclockwise
direction.Separate the door handle 4 of the freezer in the
same order. (You do not need to follow the above procedure
for the hidden handle.)
2
3
1
3
2
4
on
the top, separate the right hinge cover 5 to separate the
connecting cable 9 .Separate the bolt 7 fixating the upper
right hinge 8 ,and carefully separate the refrigerator door 10 .
7
9
8
10
3.After separating the upper left cap 11 of the separated
refrigerator door 10 , carefully take off the top cap 12 and
pull the cable 13 to connect to the hole on the left side.Set
the separated top cap 12 at the regular position and set the
cap 11 on the cable hole on the right side.Loosen the screw
32 under the cold room door 10 , move it to the left of the
stopper 31 , and then connect it.
6
5
2.After unscrewing the screw 6 of the right hinge cover 5
12
13
11
10
4.Use a sharp gimlet or knife to disconnect the cap 15 from the
cover front 14 , loosen the screw 16 , and then move the cable
18 to the left to be mounted. Disconnect the cable 40 and the
door switch 38 from the disconnected cover front 14 , swap the
position of the disconnected cable 40 and door switch 38 with
the cap 39 , mount them, fix them with the screw 16 , and then
install the cap 15 .
31
32
18
40
19
38
14
39
16
30
15
35
5. Loosen the bolt 20 of the Hinge Middle 21
, remove the Hinge
Middle 21 , and lift up the freezer door 30 to separate it.
(When separating the refrigerator door, separate the bush 35
together.)Separate the hinge cover 24 and set it on the separated
part of middle hinge 21 . After unscrewing the screw connected
to the bottom cover25 connect the cover cap26 on the right side.
Loosen the pin 29 in counterclockwise direction and move to the
hole on the left side to tighten in clockwise direction. Loosen
the bolt 27 connected to the lower hinge28 . Unscrew the screw
32 fixating the door stopper 31 at the bottom of the freezer door
30 , and fixate it on the hole on the left side with the door
stopper 31 .And then, move the upper cap 33 to the right and
cover it.
22
23
21
20
24
33
28
9
27
30
26
31
32
25
6. Set the separate lower hinge 28
on the bottom hole of the left
side of the freezer, and tighten the bolt 27 . After fixating the
bottom cover 25 at the regular position, align the freezer door 30
on the pin of lower hinge 29 to attach it properly. Turn over
the separated middle hinge 21 and sheet hinge22 to assemble
them. And set the bush 35 and washer 23 together to tighten
the bolt 20 . (When tightening the bolt, be careful not to cause
an scratch on the cap decor on top of the freezer door).
21
20
30
28
27
25
7. After assembling the door by aligning the hinge hole on the
6
36
door 10
bottom of the refrigerator
and the pin of the middle
hinge 21 , connect properly to the hold of the upper left hinge
37 included in the owner’s manual. After connecting the cable
9 , tighten the bolt 7 to screw the screws 6 to the left hinge
cover 36 included in the owner’s manual. Move the hinge cover
19 attached on the left side to the right and attach it.
19
7
37
9
10
38
8. Move the separated door handle 1
to the right and fixate the
screw 3 on the right position to attach the door cap 2 . Move
the door cap 38 on the right side to the left and attach it. Attach
the freezer door handle 2 in the same method as the refrigerator
door handle 1 .
Note
Reversing the doors is not covered by the warranty.
31
29
3
2
38
3
2
32
Download PDF

advertising