LG | 32LY330C | LG 32LY330C Owner’s Manual

OWNER’S MANUAL
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating
your set and retain it for future reference.
LY33**
LY34**
LY54**
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
LICENSES
20 SPECIFICATIONS
3
OPEN SOURCE SOFTWARE
NOTICE
23 IR CODES
4
ASSEMBLING AND
PREPARING
4
5
6
7
8
9
9
10
10
12
Unpacking
Separate Purchase
Parts and Button
Using the Joystick Button
Lifting and Moving the TV
Setting up the TV
-Attaching the Stand
-Mounting on a Table
-Mounting on a Wall
-How to use Dual Lock™
24 EXTERNAL CONTROL
DEVICE SETUP
24 RS-232C Setup
24 Type of Connector:
D-Sub 9-Pin Male
24 RS-232C Configurations
25 Communication Parameters
25 Command Reference List
26 Transmission / Receiving
Protocol
13 MAKING CONNECTIONS
13
14
14
14
15
Antenna Connection
Satellite Dish Connection
Network Setup
-Wired network connection
Other Connections
17 REMOTE CONTROL
19 MAINTENANCE
19 Cleaning your TV
19 -Screen, Frame, Cabinet and
Stand
19 -Power Cord
19 TROUBLESHOOTING
WARNING
yy If you ignore the warning message, you may
be seriously injured or there is a possibility
of accident or death.
CAUTION
yy If you ignore the caution message, you may
be slightly injured or the product may be
damaged.
NOTE
yy The note helps you understand and use
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo
are trademarks or registered trademarks of HDMI Licensing LLC in the United States
and other countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX Certified® device that has
passed rigorous testing to verify that it plays DivX video. Visit divx.com for more
information and software tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or
its subsidiaries and are used under license.”
“Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274”
OPENSOURCESOFTWARENOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the
product.
ENGLISH
ENG
LICENSES
4
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
yy Image shown may differ from your TV.
yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy The available menus and options may differ from the input source or product model that you are
using.
yy New features may be added to this TV in the future.
yy The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
be turned off if it will not be watched for some time, as this will reduce energy consumption.
yy The energy consumed during use can be significantly reduced if the level of brightness of the picture
is reduced, and this will reduce the overall running cost.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual
product and item.
CAUTION
yy Do not use any unapproved items to ensure the safety and product life span.
yy Any damages or injuries by using unapproved items are not covered by the warranty.
yy Some models have a thin film attached on to the screen and this must not be removed.
NOTE
yy The items supplied with your product may vary depending on the model.
yy Product specifications or contents of this manual may be changed without prior notice due to upgrade
of product functions.
yy For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB FLASH
DRIVE does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
< 18 mm
*B =
ENGLISH
ENG
ENGLISH
ENG
ASSEMBLING AND PREPARING
5
ENGLISH
ENG
Remote control,
Batteries (AAA)
Owner’s manual
Cable Holder
(Depending on model)
Power cord
(Depending on model)
Stand Screws
4EA, M4 x L14
(Except for 32LY33**,
32LY34**, 32LY54**)
Stand Screws
4EA, M4 x L20
(Only 32LY33**,
32LY34**, 32LY54**)
Cable Managements
2EA
Wall mount spacers
2EA
(Only 42LY33**, 42LY34**,
42LY54**)
Stand Base
Dual Lock™
(Only LY54**)
Separate Purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
LG Audio Device
LED Clock
LEC-002
(Only LY54 series)
The model name or design may be changed depending on the upgrade of product functions, manufacturer’s
circumstances or policies.
6
ASSEMBLING AND PREPARING
ENG
ENGLISH
Parts and Button
Screen
Speakers
Remote control sensor
Power Indicator
Joystick button
(* This button is located below the TV screen.)
NOTE
yy You can set the power indicator light to on or off by selecting OPTION in the main menus.
ASSEMBLING AND PREPARING
7
You can simply operate the TV functions, pressing or moving the joystick button up, down, left or right.
Basic Functions
Power On
When the TV is turned off, place your finger on the joystick button
and press it once and release it.
Power Off
When the TV is turned on, place your finger on the joystick button
and press it once for a few seconds and release it.
(However, if the Menu button is on the screen, pressing and
holding the joystick button will let you exit the Menu.)
Volume
Control
If you place your finger over the joystick button and move it left or
right, you can adjust the volume level you want.
Programmes
Control
If you place your finger over the joystick button and move it up or
down, you can scrolls through the saved programmes you want.
NOTE
yy When your finger over the joystick button and push it to the up, down, left or right, be careful not to
press the joystick button. If you press the joystick button first, you can not adjust the volume level and
saved chennels.
Adjusting the Menu
When the TV is turned on, press the joystick button one time.
You can adjust the Menu items ( , , , ) moving the joystick button up, down, left or right.
TV Off
Turn the power off.
Settings
Accesses the main menu.
Input List
Changes the input source.
Close
Clears on-screen displays and return to TV viewing.
ENGLISH
ENG
Using the Joystick Button
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and Moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
yy When transporting a large TV, there should be
at least 2 people.
yy When transporting the TV by hand, hold the TV
as shown in the following illustration.
CAUTION
yy Avoid touching the screen at all times, as
this may result in damage to the screen.
yy It is recommended to move the TV in the box
or packing material that the TV originally came
in.
yy Before moving or lifting the TV, disconnect the
power cord and all cables.
yy When holding the TV, the screen should face
away from you to avoid damage.
yy Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
yy When transporting the TV, do not expose the
TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
yy Do not apply excessive pressure to cause
flexing /bending of frame chassis as it may
damage screen.
ASSEMBLING AND PREPARING
Attaching the Stand
CAUTION
* Image shown may differ from your TV.
1
2
A Stand Base
B Stand Base
3
M4 x L14
(Except for 32LY33**,
32LY34**, 32LY54**)
M4 x L20
4EA (Only 32LY33**,
32LY34**, 32LY54**)
yy When attaching the stand to the TV, place
the screen facing down on a cushioned
table or flat surface to protect the screen
from scratches.
ENGLISH
ENG
Setting up the TV
9
10 ASSEMBLING AND PREPARING
ENG
ENGLISH
Mounting on a Table
1 Lift and tilt the TV into its upright position on a
table.
-- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
1 Insert and tighten the eye-bolts, or TV brackets
and bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
yy Make sure that children do not climb on or
hang on the TV.
NOTE
2 Connect the power cord to a wall outlet.
CAUTION
yy Do not place the TV near or on sources
of heat, as this may result in fire or other
damage.
yy Use a platform or cabinet that is strong and
large enough to support the TV securely.
yy Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
Mounting on a Wall
Securing the TV to a Wall
* This feature is not available for all models.
Attach an optional wall mount bracket at the rear
of the TV carefully and install the wall mount
bracket on a solid wall perpendicular to the
floor. When you attach the TV to other building
materials, please contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
ASSEMBLING AND PREPARING
Make sure to use screws and wall mount bracket
that meet the VESA standard. Standard dimensions
for the wall mount kits are described in the following
table.
Model
VESA (A x B)
Standard screw
32LY33**
32LY34**
32LY54**
200 x 200
M6
Number of screws 4
39LY33**
39LY34**
39LY54**
200 x 200
M6
4
Wall mount bracket
LSW240B
MSW240
Model
42/47/55LY33**
60LY33**
42/47/55LY34**
60LY34**
42/47LY54**
VESA (A x B)
400 x 400
Standard screw M6
Number of screws 4
LSW440B
Wall mount bracket
MSW240
LSW440B
MSW240
400 x 400
M6
4
LSW440B
A
B
CAUTION
yy Disconnect the power first, and then move
or install the TV. Otherwise electric shock
may occur.
yy If you install the TV on a ceiling or slanted
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and
contact the local dealer or qualified
personnel.
yy Do not over tighten the screws as this may
cause damage to the TV and void your
warranty.
yy Use the screws and wall mounts that meet
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
NOTE
yy Use the screws that are listed on the VESA
standard screw specifications.
yy The wall mount kit includes an installation
manual and necessary parts.
yy The wall mount bracket is not provided.
You can obtain additional accessories from
your local dealer.
yy The length of screws may differ depending
on the wall mount. Make sure to use the
proper length.
yy For more information, refer to the manual
supplied with the wall mount.
NOTE
yy Only 42LY33**, 42LY34**, 42LY54**
Wall Mount
Spacers
ENGLISH
ENG
Separate Purchase(Wall Mounting Bracket)
11
12 ASSEMBLING AND PREPARING
ENG
ENGLISH
How to use Dual Lock™
(Only LY54**)
Fix the set-top box to the TV and use it when you
want to.
1 After removing the protection paper from the
Dual Lock, stick it to the TV and the set-top
box as shown.
Dual Lock™
2 Attach the set-top box to the TV by pressing
the Velcro strips together.
NOTE
yy Please make sure no foreign substances
exist on the surface of the product, and
then firmly attach the Dual Lock.
yy Before attaching the set-top box to the
TV set, let the attached Dual Lock dry for
at least three days.
MAKING CONNECTIONS
Antenna Connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
* Image shown may differ from your TV.
* Any separate cable is not provided.
This section on MAKING CONNECTIONS mainly
uses diagrams for the LY33** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information on external device’s
connection, refer to the manual provided with each
device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
Wall Antenna
Socket
ANTENNA/
CABLE IN
NOTE
yy The external device connection may differ
from the model.
yy Connect external devices to the TV
regardless of the order of the TV port.
yy If you record a TV program on a DVD
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
on recording, refer to the manual provided
with the connected device.
yy Refer to the external equipment’s manual for
operating instructions.
yy If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
yy In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE
menu until the picture is clear.
yy In PC mode, some resolution settings may
not work properly depending on the graphics
card.
yy Only a USB storage device is recognizable.
yy If the USB storage device is connected
through a USB hub, the device is not
recognizable.
NOTE
yy Use a signal splitter to use more than 2 TVs.
yy If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
yy If the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
yy An antenna cable and converter are not
supplied.
yy Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
ENGLISH
ENG
MAKING
CONNECTIONS
13
14 MAKING CONNECTIONS
NetworkSetup
(Only satellite models)
Wirednetworkconnection
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
/DVI IN
2
CLOCK
(Only LY34**, LY54**)
This TV can be connected to a Pro:Centric server
via the LAN port. After making the physical connection, the TV needs to be set up for network
communication.
Connect the LAN port of the Modem or Router
from Pro:Centric server to the LAN port on the TV.
IN 3
SPEAKER OUT
AV
(RGB)
H/P OUT
1
AUDIO IN
COMPONENT
OPTICAL
(COMPONENT/RGB/DVI) AUDIO OUT
IN
PCMCIA CARD SLOT
ENG
ENGLISH
SatelliteDishConnection
VOLUME CONTROL
STEREO (8 Ω)
RS-232C
IN
Satellite
Dish
(CONTROL & SERVICE)
LNB ANTENNA/
Satellite CABLE IN
USB IN
LAN
LAN
Broadband Modem
Router
Pro:CentricServer
Broadband Modem
Pro:CentricServer
CAUTION
y Do not connect a modular phone cable to
the LAN port.
y Since there are various connection methods,
please follow the specifications of your
telecommunication carrier or internet service
provider.
15
MAKING CONNECTIONS
V
B)
ENGLISH
ENG
OtherConnections
Connect your TV to external devices. For the best picture and audio quality, connect the external device
and the TV with the HDMI cable as shown.
*ImageshownmaydifferfromyourTV.
ANTENNA/
CABLE
IN
Anyseparatecableisnotprovided.
*ANTENNA/
CABLE IN
(Only Support Network Model)
EXTERNAL
SPEAKER OUT
EXTERNAL
SPEAKER OUT
IN
OPTICAL
DIGITAL
AUDIO OUT
IN
1
IN
/DVI
EXTERNAL
/DVIIN
IN
EXTERNAL
IN
OPTICAL
1
1 1
EXTERNAL
EXTERNAL
DIGITAL /D
1
EXTERNAL
VOLUME
AV
AV
AV
/DVI
IN
OPTICAL
11
2EXTERNAL
AV
OPTICAL
2
SPEAKER
OUT
AUDIO
IN
AUDIO
OUT
IN
SPEAKER
SPEAKER
OUT
CONTROL
(RGB)
AV
AVAV
AUDIO IN
(RGB)
SPEAKER
OUT
DIGITAL
ININ
OPTICAL
VOLUME
DIGITAL
AV
(RGB)
AUDIO
ININ
PONENT
OPTICAL
OPTICAL 1
OPTICAL
ANTENNA/
VOLUME
(COMPONENT/RGB/DVI)
AUDIO
MPONENT
OPTICAL (RGB)
(COMPONENT/RGB/DVI)
OPTICAL
(RGB)
OPTICAL
(RGB)
B)
(RGB)
(COMPONENT/RGB/DVI)
ININ
AUDIO
EXTERNAL
AUDIO
CABLE
INOUTOUT
OPTICAL
(COMPONENT/RGB/DVI)
AUDIOOUT
OUT
1 1VOLUME
DIGITAL
AUDIO
AV AUDIO
DIGITAL
CONTROL
1 DIGITAL
2
(Only
(RGB)
CONTROL
IN
DIGITAL
RNAL
DIGITAL
VOLUME
ERNALCOMPONENT AUDIO
H/P
H/POUT
OUT DIGITAL
AUDIO
OUT
SPEAKER
OUT
AUDIO
OUT
IN
AUDIO
OUT
AUDIO
OUT
Satellite Models)
(RGB)
CONTROL
ER
OUT
IN
AUDIO
OUT
AUDIO
COMPONENT
AV
AV
KER OUT IN
AUDIO IN
COMPONENT
OPTICAL
(Only
LY54**)
(COMPONENT/DVI)
AUDIO OUT
AV
CONTROL
OPTICAL
(COMPONENT/RGB/DVI)
OP
OPTICAL AUDIO OUT
AUDIOAUDIO
IN INRS-232C IN RGB IN (PC) (RGB)
(COMPONENT
IN
(COMPONENT/RGB/DVI)
IN
1
(RGB)
(RGB)
LNB LNB ANTENNA/
DIGITAL
CLOCK
(CONTROLVOLUME
& SERVICE)
DI
DIGITAL
EXTERNAL
ANTENNA/
EXTERNAL
CLOCK
(COMPONENT/DVI)
AUDIO
IN
AKER
OUT
AUDIO
IN
AUDIO
IN
(COMPONENT/DVI)
EAKER
OUT
OUT
P OUT
AUDIO
OUT
AUDIOCONTROL
IN
COMPONENT
AUD
SPEAKER
OUT
ANTENNA/
ANTENNA/
SPEAKER OUT
Satellite
CABLE
IN
AUDIO
OUT
AV
LNB
ANTENNA/
ANTENNA/
LNBLNB
IN INANTENNA/
Satellite
CABLE
IN
H/P
OUT
(COMPONENT/RGB/DVI)
(COMPONENT/DVI)
(COMPONENT/RGB/DVI)
LNB
ANTENNA/
(COMPONENT/DVI)
CABLE
IN IN
CABLE
(RGB)
OSatellite
ININ SatelliteCABLE
DVI)
CABLE IN
IN IN
DIO
COMPONENT
Satellite
CABLE INCABLE INSatellite
COMPONENT
CLOCK
NENT/DVI)
ONENT/DVI)
C
(Only
LY54**)
RS-232C
IN
SPEAKER
OUT
H/P OUT
ANTENNA/
SPEAKER
UME
ANTENNA/
COMPONENT
AUDIO
IN
H/P OUT OUT CLOCK
LUMECONTROL
CONTROL IN IN
LNB
COMPONENT
COMPONENT
ANTENNA/
LNBININ ANTENNA/
H/P OUT COMPONENT
RS-232C
ININ
(CONTROL
&
SERVICE)
CABLE
RS-232C
LNB
ANTENNA/
CABLE
CABLE
ININ
(COMPONENT/DVI) 1RS-232C
CABLE
Satellite
ININININSatellite
CLOCK
RS-232C
IN
ONENT
1
CLOCK
PONENTEXTERNAL
AUDIO IN EXTERNAL
IN
Satellite
CABLE IN
AUDIO IN
RS-232C
INOUT
ININ(PC)
NIN SPEAKER OUT
(CONTROL
&
SERVICE)
SPEAKER
(COMPONENT/DVI)
RS-232C
IN RGB
(CONTROL
&
SERVICE)
CLOCK
RGB
IN
(PC)
RS-232C
IN
RGB
(PC)
AV
AV
(COMPONENT/DVI)
TEREO
(8
Ω)
RS-232C
IN
ANTENNA/
CLOCK
OPTICAL
OPTICAL
LAN VOLUME
STEREO (8 Ω)
CONTROL
(CONTROL
&
SERVICE)
(RGB)
(RGB)
LNB IN ANTENNA/
LAN VOLUME CONTROL
(CONTROL
& SERVICE) RS-232C
DIGITAL
DIGITAL
(CONTROL
& SERVICE)
COMPONENT
VOLUME
RS-232C
IN IN
IN
(CONTROL & SERVICE)
RGB
ININ(PC)
CABLEIN
RS-232C
H/P OUT
RGB
(PC)
AUDIO
OUT
AUDIO OUT
CONTROL(CONTROL
)
Satellite CABLE
R
&&SERVICE)
(CONTROL
(CONTROL
SERVICE)
(CONTROL& SERVICE)
& SERVICE)
IN
COMPONENT
RGB IN (PC)
COMPONENT
IN AUDIO IN
AUDIO IN
PC) (COMPONENT/DVI)
CLOCK
ANTENNA/
LNB IN ANTENNA/RS-232C IN
IN
(COMPONENT/RGB/DVI)
H/P SPEAKER
OUT SPEAKER
OUT OUT
1
IN
IN
IN
1
IN
STEREO (8 Ω)
(CONTROL & SERVICE)(Only LY54**)
COMPONENT
IN
COMPONENT
IN
HDMI
DVD/
Blu-Ray
RGB
IN (PC)/ HD Cable Box
/ HD STB / PC
RGB IN (PC)
AUDIO OUT
RS-232C IN
(CONTROL & SERVICE)
RS
1
AV OPTICAL
DIGITAL
(RGB)AUDIO OUT
AV
(RGB)
+
-
LNB
Satellite
RS-232C IN
CLOCK (CONTROL & SERVICE)
IN
(CONTR
(CONTRO
1
AUDIO IN
(COMPONENT/DVI)
H/P OUT
COMPONENT
IN
LED Clock
STEREO (8 Ω)
IN
AUDIO OUT
AUDIO IN
(COMPONENT/DVI)
AUDIO
AUDIO/ VIDEO
/ VIDEO
CABLE IN
RGB IN (PC)
OPTICAL
VOLUME
DIGITAL
CONTROL
AUDIO IN
VOLUME
(COMPONENT/RGB/DVI)
CONTROL
AUDIO IN
(COMPONENT/RGB/DVI)
OPTICAL
OPTICALAUDIO
AUDIOININ
RS-232C IN
(CONTROL
& SERVICE)
(CONTROL & SERVICE)
EXTERNAL
RS-232C IN
RGB IN (PC)
(CONTROL & SERVICE) SPEAKER OUT
EXTERNAL
SPEAKER OUT
RS-232C IN
CLOCK
(CONTROL & SERVICE)
H/P OUT
2
IN
Satellite CABLE IN
COMPONENT
IN
N (PC)
x
1
AV
(RGB)
ANTENNA/
CABLE IN
CLOCK
HDMI
RGB OUT (PC)
DVD/ Blu-Ray / HD Cable Box
/ HD STB / PC
AUDIO / VIDEO
Digital
Audio
System
Digital
Audio
Digital
AudioSysterm
System
OPTICAL AUDIO IN
PC
Digital Audio System
DVD / Blu-Ray /
HD Cable Box /
HD STB / PC
OPT
16 MAKING CONNECTIONS
1
UDIO
IN IN
NENT/RGB/DVI)
/RGB/DVI)
B/DVI)
VOLUME
VOLUME
CONTROL
CONTROL
AUDIOAUDIO
IN IN
EXTERNAL
(COMPONENT/DVI)
(COMPONENT/DVI)
SPEAKER
OUT
USB IN
USB IN 2
USB
HDD
USB IN 1
IN
2 (MHL)
H/P OUT
IN
IN
1
1
AV
AVMobile
OPTICAL
OPTICAL
(RGB)
(RGB)
DIGITAL
DIGITAL
AUDIO
AUDIO
OUTOUT Headphone
Headphone
Mobile Phone
Phone
IN
1
OPTICAL
DIGITAL
EXTERNAL
RS-232C
IN (PC)
RS-232C
IN IN RGBRGB
IN (PC)
SPEAKER OUT AUDIO OUT
(CONTROL
& SERVICE)
(CONTROL
& SERVICE)
1 AUDIO
1 IN
EXTERNAL
ANTENNA/
ANTENNA/
CABLE
CABLE
IN IN
AV
(RGB)
IN
OPTICAL
1DIGITAL
VOLUME
EXTERNAL
LNB
AUDIO
IN OUT
AUDIO
OUT
(COMPONENT/DVI)
CONTROL
SPEAKER
SPEAKER OUT
AV
AV AV
Satellite
(COMPONENT/RGB/DVI)
OPTICAL
OPTICAL
OPTICAL
OPTICAL
(RGB)
(RGB)
EXTERNAL
(RGB)
DIGITAL
DIGITAL
AUDIO IN DIGITAL
VOLUME
VOLUME
DIGITAL
COMPONENT
H/PAUDIO
OUT
IN AUDIO
SPEAKER
OUTOUT
AUDIO OUT
AUDIO INCONTROL
AUDIO
AUDIO
OUTOUT
(COMPONENT/DVI)
CONTROL
IN
Control port
(COMPONENT/RGB/DVI)
(COMPONENT/RGB/DVI)
IN
Or
for Speaker out
RS-232C IN
CLOCK VOLUME
1AUDIO IN
AUDIO
IN IN & SERVICE)
COMPONENT
(CONTROL
AUDIO
H/P
OUT
CONTROL
LNB
UP
ANTENNA/
+
(COMPONENT/DVI) LNB LNB (COMPONENT/RGB/DVI)
ANTENNA/
(COMPONENT/DVI)
IN
+
Satellite
AV
Satellite
CABLE
IN
DOWN
IN
Satellite
CABLE
IN
RGB IN (PC)
RS-232C
IN IN
-OPTICAL
CLOCK
AUDIO
(RGB)1
COMPONENT
COMPONENT
(CONTROL
&
SERVICE)
H/P OUT DIGITAL
H/P
OUT
(COMPONENT/DVI)
AUDIO OUT
IN
IN
AV
RGB
IN
(PC)
RS-232C IN
IN
CLOCK RS-232C
RS-232C
IN INOPTICALCLOCK
+CLOCK
RS-232C
CLOCK
(RGB)
COMPONENT
DIGITAL
H/P(CONTROL
OUT & SERVICE)
(CONTROL & SERVICE)
(CONTROL
& SERVICE)
(CONTROL
&GND
SERVICE)
IN
LNB
ANTENNA/
AUDIO OUT
RIGHT
Satellite
CABLE
IN
RGB IN (PC)
RGB IN (PC)
(CO
LEFT
ANTENNA/
LNB
GND
Satellite
CABLE INRGB IN (PC)
RS-232C IN
CLOCK
(CONTROL & SERVICE)
L
VIDEO
RED
WHITE
RED
GND / Up / Down CPU detects
transition from
3.3V to GND
level for volume
control.
RED
3.3V with CPU
GPIO.
RED
COMPONENT
INMethod of Volume control port
RS-232C INEach Up/ Down
CLOCK
(CONTROL & SERVICE)
pin is pulled to
Cable
Spec.
IN
IN
Mobile Phone
BLUE
AUDIO IN
COMPONENT
(COMPONENT/DVI)
IN
AUDIOAUDIO
IN IN
(COMPONENT/RGB/DVI)
(COMPONENT/RGB/DVI)
EXTERNAL
SPEAKER
OUT
COMPONENT
COMPONENT
IN IN
VOLUME
CONTROL
BLUE
AUDIO
IN
VOLUME
(COMPONENT/DVI)
CONTROL
AUDIO IN
(COMPONENT/RGB/DVI)
H/P H/P
OUTOUT
BLUE
VOLUME
COMPONENT
EXTERNAL
COMPONENT
CONTROL
IN INOUT
SPEAKER
IN
2 (MHL)
IN (Only
ANTENNA/LY54**)
LNB LNB
IN ANTENNA/
Satellite
CABLE
Satellite
CABLE
IN IN
RS-232C
RS-232C
IN IN CLOCK
CLOCK
(CONTROL
& SERVICE)
(CONTROL
& SERVICE)
EXTERNAL
EXTERNAL
SPEAKER
OUT OUT
SPEAKER
MHL passive cable
EXTERNAL
EXTERNAL
SPEAKER
SPEAKER
OUT OUT
H/P OUT
AV AV
OPTICAL
OPTICAL
(RGB)
(RGB)
DIGITAL
DIGITAL
AUDIO
AUDIO
OUTOUT
H/P OUT
IN
2 (MHL)
USB IN
USB IN 2
USB IN 1
1
HUB
HUB
GREEN
N (PC)
1
USB
HDD
GREEN
PC)
IN
USB
USB
GREEN
VI)IN (PC)
B(PC)
IN
USB
PCMCIA Card
PONENT
ENT
IN
RS-232C
RS-232C
IN IN RGBRGB
IN (PC)
IN (PC)
(CONTROL
& SERVICE)
(CONTROL
& SERVICE)
IN
2 (MHL)
UDIO
IN IN
ONENT/DVI)
NT/DVI)
Mobile Phone
PCMCIA Card
PCMCIA Card
H/P OUT
OLUME
ME
ONTROL
OL
CABLE
CABLE
IN IN
USB IN
TERNAL
NAL
AKER
OUT OUT
ANTENNA/Card
PCMCIA
ANTENNA/
IN
2 (MHL)
PONENT
NENT
IN
PCMCIA Card
AV AV
(RGB)
(RGB)
Headphone
IN
1
Mobile Phone
H/P
OUTOUT
IN
R
AUDIO
H/P OUT
ENG
ENGLISH
TERNAL
NAL
RAKER
OUT OUT
OPTICAL
OPTICAL
DIGITAL
DIGITAL
AUDIO
AUDIO
OUTOUT
DVD / Blu-Ray /
HD Cable Box
REMOTE CONTROL
17
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching
the
and
ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
yy Do not mix old and new batteries, as this may damage the remote control.
Make sure to point the remote control toward the remote control sensor on the TV.
(Only LY33**, LY34**)
TV/
RAD
AV MODE
(POWER) Turns
the
RATIO
INPUT TV on or off.
TV/RAD
Selects Radio, TV and DTV programme.
SUBTITLE Recalls your preferred subtitle in digital mode.
AV MODE Selects an AV mode.
RATIO
Resizes
.,;@
abc an image.
def
INPUT
Changes the input source.
1
2
4
5
ghi
Number buttons
3
6
jklEnters
mno
numbers.
LIST Accesses the saved programme list.
pqrs
tuv
Q.VIEW Returns
to the wxyz
previously viewed programme.
7
MUTE
0
- Adjusts
Q.VIEWlevel.
LIST the volume
FAV Accesses your favourite programme list.
GUIDE Shows FAV
programme guide.
FAV
GUIDE
9
[
+
8
P
PAGE
MUTE Mutes all sounds. PA
P GE programmes or channels.
ꕌPꕍ Scrolls through the saved
MUTE to the previous or next screen.
ꕌPAGEꕍ Moves
Teletext buttons (
INFO
TEXT/T.OPT) These buttons are used for teletext.
SETTINGS
MY APPS
Views the information
of the current programme and screen.
SETTINGS Accesses the main menus.
Q. MENU Accesses the quick menus.
OK
OK
Selects menus
or options and confirms your input.
Navigation buttons (up/down/left/right) S crolls through menus or
options.
BACK Returns to the previous level.
EXIT Clears allREC/
on-screen
* EXIT displays and return to TV viewing.
Accesses the AV devices connected with the HDMI cable
through HDMI-CEC. Opens the SIMPLINK menu.
AD By pressing the AD button, audio descriptions function will be enabled.
Control buttons (
) Controls the MY MEDIA menus or the
SIMPLINK compatible devices (USB,SIMPLINK).
SUBTITLE
LIVE TV
Colour buttons TheseREC
access special functions in some menus.
( : Red,
: Green,
: Yellow,
: Blue)
INFO
ENGLISH
ENG
REMOTE CONTROL
18 REMOTE CONTROL
ENG
ENGLISH
(Only LY54**)
ENERGY
AV MODE
(POWER) Turns the TV on or off.
ꕊ ENERGY SAVING Adjusts the brightness of the screen to reduce
energy consumption.
AV MODE Selects an AV mode.
INPUT Changes the input source.
TV/RAD
Selects Radio, TV and DTV programme.
INPUT
TV/
RAD
SAVING
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
Number buttons Enters numbers.
LIST Accesses the saved programme list.
Q.VIEW Returns to the previously viewed programme.
FAV
RATIO
P
MUTE
GUIDE PORTAL INFO
OK
SETTINGS
Q.MENU
EXIT
AD
ALARM
P
A
G
E
+
- Adjusts the volume level.
FAV Accesses your favourite programme list.
RATIO Resizes an image.
MUTE Mutes all sounds.
ꕌPꕍ Scrolls through the saved programmes or channels.
PAGE Moves to the previous or next screen.
GUIDE Shows programme guide.
PORTAL Displays and removes hotel interactive menu.
INFO Views the information of the current programme and screen.
Navigation buttons (up/down/left/right) Scrolls through menus or
options.
OK Selects menus or options and confirms your input.
SETTINGS Selects a menu. Clears all on-screen displays and returns
to TV viewing from any menu.
Returns to the previous level.
EXIT Clears on-screen displays and return to TV viewing.
Coloured buttons These access special functions in some menus.
Teletext buttons ( TEXT/T.OPT) These buttons are used for teletext.
SUBTITLE Recalls your preferred subtitle in digital mode.
Control buttons (
) Controls the MY MEDIA menus, or
the SIMPLINK compatible devices (USB,SIMPLINK).
Accesses the AV devices connected with the HDMI cable
through HDMI-CEC. Opens the SIMPLINK menu.
Q.MENU Accesses the Quick menus.
AD By pressing the AD button, audio descriptions function will be enabled.
ALARM Sets the alarm function.
MAINTENANCE / TROUBLESHOOTING
19
ENGLISH
ENG
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
yy Make sure to turn the power off and disconnect the power cord and all other cables first.
yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall
outlet to prevent possible damage from lightning or power surges.
Screen, Frame, Cabinet and Stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
yy Avoid touching the screen at all times, as this may result in damage to the screen.
yy Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in
scratches and image distortions.
yy Do not use any chemicals as this may damage the product.
yy Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
malfunction.
Power Cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
The software version can be updated for improvement in performance.Customer needs to ensure the
compatibility of customer’s equipment with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Problem
Solution
Cannot control the
TV with the remote
control.
yy Check the remote control sensor on the product and try again.
yy Check if there is any obstacle between the product and the remote control.
to ,
to
yy Check if the batteries are still working and properly installed (
No image display
and no sound is
produced.
yy Check if the product is turned on.
yy Check if the power cord is connected to a wall outlet.
yy Check if there is a problem in the wall outlet by connecting other products.
The TV turns off
suddenly.
yy Check the power control settings. The power supply may be interrupted.
yy Check if the Automatic Standby (Depending on model) / Sleep Timer / Off Time
feature is activated in the TIME settings.
When connecting to
the PC (RGB/HDMI
DVI), ‘No signal’ or
‘Invalid Format’ is
displayed.
yy Turn the TV off/on using the remote control.
yy Reconnect the RGB/HDMI cable.
yy Restart the PC with the TV on.
).
20 SPECIFICATIONS
ENG
ENGLISH
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
MODELS
32LY33**
39LY33**
42LY33**
32LY330C-ZA
39LY330C-ZA
42LY330C-ZA
Dimensions
(W x H x D)
With stand (mm)
732 x 481 x 207
885 x 567 x 218
961 x 612 x 218
Without stand (mm)
732 x 431 x 55.5
885 x 524 x 55.5
961 x 567 x 55.5
Weight
With stand (kg)
6.2
8.3
9.5
Without stand (kg)
6.0
8.0
9.2
Power requirement
Power consumption
MODELS
AC 100-240 V~ 50 / 60 Hz
65 W
90 W
100 W
47LY33**
55LY33**
60LY33**
47LY330C-ZA
55LY330C-ZA
60LY330C-ZA
Dimensions
(W x H x D)
With stand (mm)
1073 x 676 x 246
1243 x 772 x 247
1373 x 851 x 283
Without stand (mm)
1073 x 629 x 55.8
1243 x 725 x 56.8
1373 x 801 x 58.8
Weight
With stand (kg)
12.7
18.4
23.5
Without stand (kg)
12.3
18.0
23.0
Power requirement
Power consumption
MODELS
AC 100-240 V~ 50 / 60 Hz
110 W
130 W
140 W
32LY34**
39LY34**
42LY34**
32LY340C-ZA
32LY345C-ZA
39LY345C-ZA
42LY345C-ZA
Dimensions
(W x H x D)
With stand (mm)
732 x 481 x 207
885 x 567 x 218
961 x 612 x 218
Without stand (mm)
732 x 431 x 55.5
885 x 524 x 55.5
961 x 567 x 55.5
Weight
With stand (kg)
6.2
8.3
9.5
Without stand (kg)
6.0
8.0
9.2
Power requirement
Power consumption
MODELS
AC 100-240 V~ 50 / 60 Hz
65 W
90 W
100 W
47LY34**
55LY34**
60LY34**
47LY345C-ZA
55LY345C-ZA
60LY345C-ZA
Dimensions
(W x H x D)
With stand (mm)
1073 x 676 x 246
1243 x 772 x 247
1373 x 851 x 283
Without stand (mm)
1073 x 629 x 55.8
1243 x 725 x 56.8
1373 x 801 x 58.8
Weight
With stand (kg)
12.7
18.4
23.5
Without stand (kg)
12.3
18.0
23.0
Power requirement
Power consumption
MODELS
AC 100-240 V~ 50 / 60 Hz
110 W
130 W
140 W
32LY54**
39LY54**
42LY54**
32LY540H-ZA
39LY540H-ZA
42LY540H-ZA
Dimensions
(W x H x D)
With stand (mm)
732 x 481 x 207
885 x 567 x 218
961 x 612 x 218
Without stand (mm)
732 x 431 x 55.5
885 x 524 x 55.5
961 x 567 x 55.5
Weight
With stand (kg)
6.2
8.3
9.5
Without stand (kg)
6.0
8.0
9.2
Power requirement
Power consumption
AC 100-240 V~ 50 / 60 Hz
65 W
90 W
100 W
SPECIFICATIONS
47LY540H-ZA
Dimensions
(W x H x D)
With stand (mm)
1073 x 676 x 246
Without stand (mm)
1073 x 629 x 55.8
Weight
With stand (kg)
12.7
Without stand (kg)
12.3
Power requirement
AC 100-240 V~ 50 / 60 Hz
Power consumption
110 W
CI Module Size
(W x H x D)
Environment
condition
ENGLISH
ENG
47LY54**
MODELS
100.0 mm x 55.0 mm x 5.0 mm
Operating
Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Satellite Digital TV1
Television system
Programme coverage
Maximum number of storable
programmes
External antenna impedance
1 Satellite and DVB-T2 support models
2 Except for DVB-T2 support models
21
Digital TV
DVB-T/T2
DVB-C
DVB-S/S2
DVB-T
DVB-C
VHF, UHF
C-Band, Ku-Band
VHF, UHF
6,000
Analogue TV
PAL/SECAM B/G/D/K,
PAL I/I’,
SECAM L/L’2
VHF: E2 to E12,
UHF : E21 to E69,
CATV: S1 to S20,
HYPER: S21 to S47
1,500
75 Ω
22 SPECIFICATIONS
ENG
ENGLISH
RGB-PC, HDMI/DVI-PC Supported Mode
HDMI/DVI-DTV Supported Mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency
(Hz)
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency
(Hz)
640 x 350
31.468
70.09
720 x 400
31.469
70.08
720 x 480
31.469
31.5
59.94
60
640 x 480
31.469
59.94
720 x 576
31.25
50
800 x 600
37.879
60.31
1280 x 720
1024 x 768
48.363
60.00
37.5
44.96
45
50
59.94
60
1152 x 864
54.348
60.053
1920 x 1080i
33.72
33.75
28.125
59.94
60
50
1920 x 1080p
26.97
27
33.716
33.75
56.25
67.43
67.5
23.97
24
29.976
30.00
50
59.94
60
1360 x 768
47.712
60.015
1280 x 1024
63.981
60.020
1920 x 1080
(RGB-PC)
66.587
59.934
1920 x 1080
(FHD only)
67.50
60.00
(Except for 32LY330C, 32LY340C, 32LY540H)
Component Port Connecting Information
Component ports on
the TV
Y
PB
PR
Video output ports
on DVD player
Y
Y
Y
Y
PB
B-Y
Cb
Pb
PR
R-Y
Cr
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
IR CODES
* This feature is not available for all models.
Code (Hexa)
Function
08
(POWER)
Note
Remote control Button (Power On/Off)
F0
TV/RAD
Remote control Button
39
SUBTITLE
Remote control Button
91
AD
Remote control Button
79
RATIO
Remote control Button
0B
INPUT
Remote control Button
10-19
Number Key 0-9
Remote control Button
53
LIST
Remote control Button
1A
Q.VIEW
Remote control Button
02
+
Remote control Button
03
-
Remote control Button
1E
FAV
Remote control Button
AB
GUIDE
Remote control Button
09
MUTE
Remote control Button
00
Pꕌ
Remote control Button
01
Pꕍ
Remote control Button
20
TEXT
Remote control Button
21
T.OPT(T.Option)
Remote control Button
43
SETTINGS
Remote control Button
45
Q.MENU
Remote control Button
AA
INFO
Remote control Button
28
BACK
Remote control Button
5B
EXIT
Remote control Button
44
OK
Remote control Button
40
Remote control Button
41
^
v
07
<
Remote control Button
06
>
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
B1
n
Remote control Button
B0
Remote control Button
BA
►
yy
8E
►►
Remote control Button
8F
◄◄
Remote control Button
7E
SIMPLINK
Remote control Button
30
AV MODE
Remote control Button
E8
ALARM
Remote control Button
0C
PORTAL
Remote control Button
95
ENERGY SAVING
Remote control Button
Remote control Button
Remote control Button
ENGLISH
ENG
IR CODES
23
24 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
EXTERNAL
SPEAKER OUT
VOLUME
CONTROL
EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup
RS-232C Configurations
Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control
system) to control the product’s functions externally.
IN to the RSConnect the serial port of the control device
1
232C jack on the product back panel.
Note: RS-232C connection cables are not supplied with
AV
OPTICAL
the product.
(RGB)
DIGITAL
AUDIO OUT
AUDIO IN
COMPONENT/DVI)
LNB
Satellite
COMPONENT
IN
7-Wire Configurations
(Standard RS-232C cable)
RXD TXD
GND
DTR
DSR
RTS
ANTENNA/
CABLE
IN
CTS
RS-232C IN
(CONTROL & SERVICE)
CLOCK
(*Not Provided)
1
5
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations
(Not standard)
Type of Connector: D-Sub 9-Pin Male
PC
RXD TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Set ID number. "Real Data Mapping".
1 Press SETTINGS or HOME to access the main
menus.
2 Press the Navigation buttons to scroll to
OPTION and press OK.
6
No.
9
Pin name
1
3.5V
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
No Connection (5V available in some models)
8
No Connection
9
No Connection (12V available in some models)
3 Press the Navigation buttons to scroll to Set ID
and press OK.
4 Scroll left or right to select a set ID number and
select Close. The adjustment range is 1-99.
5 When you are finished, press EXIT.
EXTERNAL CONTROL DEVICE SETUP
25
yy Baud rate: 9600 bps (UART)
yy Data length: 8 bits
yy Parity : None
ENGLISH
ENG
Communication Parameters
yy Stop bit: 1 bit
yy Communication code: ASCII code
yy Use a crossed (reverse) cable.
Command Reference List
(Depending on Model)
model)
01. Power
02. Aspect
Ratio
03. Screen
Mute
04. Volume
Mute
05. Volume
Control
k
a
DATA
(Hexadecimal)
00 to 01
k
c
(See p. 27)
k
d
(See p. 27)
k
e
00 to 01
k
f
00 to 64
06. Contrast
k
g
00 to 64
07. Brightness
k
h
00 to 64
08. Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 32
11. OSD Select k
l
00 to 01
12. Remote
Control
Lock Mode
m
00 to 01
COMMAND1
k
COMMAND2
13. Balance
14. Colour
Temperature
15. Energy
Saving
16. Auto Configuration
k
t
DATA
(Hexadecimal)
00 to 64
x
u
00 to 64
j
q
00 to 05
j
u
01
17. Equalize
j
v
(See p. 29)
m
a
(See p. 29)
m
b
00 to 01
m
m
c
g
(See p. 23)
00 to 64
x
b
(See p. 30)
COMMAND1
18. Tune Command
19. Programme
Add/Skip
20. Key
21. Control
Back Light
22. Input select
(Main)
COMMAND2
* Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are not
executed and treated as NG.
26 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]
[Command 2]
[Set ID]
: First command to control the TV.(j, k, m or x)
: Second command to control the TV.
: You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment
range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ]
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data00: Illegal Code
EXTERNAL CONTROL DEVICE SETUP
27
04. Volume Mute (Command: k e)
►► To control Power On/Off of the set.
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on remote
control.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data based on this
format, Acknowledgement data feed back presents status
about each function.
* OK Ack., Error Ack. and other message may display on the
screen when TV is power On.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
02. Aspect Ratio (Command: k c) (Main Picture
Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the Aspect
Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen
(16:9)
04 : Zoom
06 : Original
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect
ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p
24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i,
1080p 50 Hz / 60 Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital, Analogue, AV.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 30
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 30
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 30
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 :
01 :
10 :
Screen mute off (Picture on)
Video mute off
Screen mute on (Picture off)
Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen
Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 30
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
01. Power (Command: k a)
28 EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
09. Tint (Command: k j)
13. Balance (Command: k t)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to ‘Real data mapping’. See p. 30
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 30
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
14. Colour Temperature (Command: x u)
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Data Min : 00 to Max : 32
* Refer to ‘Real data mapping’. See p. 30
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p. 30
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling
remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
15. Energy Saving (Command: j q)
►► To reduce the power consumption of the TV. You can also
adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
12. Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and remote
control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
Power Saving
Function
7
6
5
4
0
0
0
0
0
0
0
0
0
* If you are not using the remote control, use this mode.
When main power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by
power on key of IR & Local Key.
0
Description
3
2
1
0
Low
Power
0
0
0
0
Off
0
Low
Power
0
0
0
1
Minimum
0
0
Low
Power
0
0
1
0
Medium
0
0
0
Low
Power
0
0
1
1
Maximum
0
0
0
0
Low
Power
0
1
0
1
Screen Off
0
0
0
0
Low
Power
0
1
0
0
Auto
01 : Lock on
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
Level
►► 'Auto' is available in TV that supports 'Intelligent Sensor'
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
29
►► Select channel to following physical number.
►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
Data00 :High channel data
Data01 :Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 :[Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
17. Equalize(Command: j v)
►► To adjust equalize.
Transmission [j][v][ ][Set ID][ ][Data][Cr]
MSB
0
0
0
0
0
Frequency
7
6
5
0
0
0
0
0
0
1
0
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
LSB
0
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
0
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data
Data Min: 00 to Max: 7DH
Frequency
4
3
2
1
0
Step
0
1’st Band
0
0
0
0
0
0(decimal)
1
2’nd Band
0
0
0
0
1
1(decimal)
1
0
3’rd Band
...
...
...
...
...
...
1
1
4’th Band
1
0
0
1
1
19(decimal)
0
0
5’th Band
1
0
1
0
0
20(decimal)
Ack [v][ ][Set ID][ ][OK/NG][Data][x]
19. Programme Add/Skip(Command: m b)
►► To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
20. Key(Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - See p. 23
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
21. Control Back Light(Command: m g)
►► To control the back light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
18. Tune Command (Command: m a)
16. Auto Configure(Command: j u)
30 EXTERNAL CONTROL DEVICE SETUP
22. Input select (Command: x b)
ENG
ENGLISH
(Main Picture Input)
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
LSB
0
0
0
0
0
0
External Input
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping
00 : Step 0
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E : Step 110
73 :
74 :
Step 115
Step 116
CF : Step 199
FE : Step 254
FF : Step 255
0
The model and serial numbers of the TV is
located on the back of the TV
Record it below should you ever need
service.
Model
Serial
Download PDF