LG | 42LT360C | LG 42LT360C Owner’s Manual

OWNER’S MANUAL
LED LCD TV
Please read this manual carefully before operating your set and retain it
for future reference.
LT36**
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
LICENSES
25
EXTERNAL CONTROL DEVICE SETUP
3
OPEN SOURCE SOFTWARE NOTICE
25
25
4
INSTALLATION PROCEDURE
4
ASSEMBLING AND PREPARING
RS-232C Setup
Type of connector;
D-Sub 9-Pin Male
RS-232C Configurations
Communication Parameters
Command reference list
Transmission / Receiving Protocol
4
7
8
9
9
11
12
14
Unpacking
Parts and buttons
Lifting and moving the TV
Setting up the TV
- Attaching the stand
- Mounting on a table
- Mounting on a wall
- Tidying cables
15
MAKING CONNECTIONS
15
15
16
16
17
17
17
18
18
18
19
19
Adapter connection
Antenna connection
HDMI connection
DVI to HDMI connection
RGB-PC connection
RS-232C Setup
Component connection
Composite connection
Speaker output SETUP
USB connection
CI module connection
Euro Scart connection
20
REMOTE CONTROL
21
MAINTENANCE
21
21
21
Cleaning your TV
- Screen, frame, cabinet and stand
- Power cord
21
TROUBLESHOOTING
22
SPECIFICATIONS
24
IR CODES
25
26
26
27
WARNING
If you ignore the warning message, you may
yy
be seriously injured or there is a possibility
of accident or death.
CAUTION
If you ignore the caution message, you may
yy
be slightly injured or the product may be
damaged.
NOTE
The note helps you understand and use
yy
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
ENGLISH
ENG
LICENSES
4
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
Image shown may differ from your TV.
yy
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy
The available menus and options may differ from the input source or product model that you are
yy
using.
New features may be added to this TV in the future.
yy
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
yy
be turned off if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the picture
yy
is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy
Some models have a thin film attached on to the screen and this must not be removed.
yy
NOTE
The items supplied with your product may vary depending on the model.
yy
Product specifications or contents of this manual may be changed without prior notice due to upgrade
yy
of product functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
yy
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory
stick does not fit into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
*B <
= 18 mm
ASSEMBLING AND PREPARING
ENGLISH
ENG
ENERGY
TV/RAD
SAVING
GUIDE
INFO
RATIO
ENERGY AV MODE INPUT
TV
SAVING
LIST
SETTINGS
1
2
4
5
7
8
LIST
0
3
6
Q.VIEW
9
FLASHBK
Q.MENU
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
EXIT
MENU INFO
Q.MENU
FAV
ENTER
P
P
A
G
E
MUTE
BACK
EXIT
L/R SELECT
FREEZE
RATIO
or
Remote control and
batteries (AAA)
(See p.20)
Owner’s manual
Cable Holder
(Depending on model)
(See p.14)
Power Cord holder
(Only 32/37/42/47LT36**)
(See p.14)
Stand Screws
4 EA, M4 x 12
2 EA, M4 x 16
(Only 22LT36**)(See p.9)
Stand Screws
8 EA, M4 x 12
(Only 26LT36**)(See p.9)
Stand Screws
8 EA, M4 x 14
(Only 32/37/42/47LT36**)
(See p.10)
Desk-mount Screw
1 EA, M4 x 20
(Only 32/37/42/47LT36**)
(See p.11)
Power cord
DC Adapter
(Only 22/26LT36**)
(See p.15)
Stand body / Stand base
(Only 22LT36**)
(See p.9)
Stand body / Stand base
(Only 26LT36**)
(See p.9)
Stand body / Stand base
(Only 32/37/42/47LT36**)
(See p.10)
Protection cover
(Only 32/37/42/47LT36**)
(See p.13)
Isolator
(Depending on model)
(See p.6)
5
6
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
Antenna Isolator Installation Guide
yy
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND of
antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact
might be heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall,
mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
2. Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection
to a cable distribution system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING
7
(Only 32/37/42/47LT36**)
ENGLISH
ENG
Parts and buttons
Screen
(Only 22/26LT36** )
HDMI IN
USB IN
USB input
IN 3
COMPONENT IN
COMPONENT
IN
PCMCIA Card Slot
Speakers
Remote control
Power Indicator
(Can be adjusted using
the Power Indicator
in the OPTION menu.)
Button
Description
∨∧
Scrolls through the saved programmes.
-+
Adjusts the volume level.
Turns the power on or off.
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
yy When transporting a large TV, there should be
at least 2 people.
yy When transporting the TV by hand, hold the TV
as shown in the following illustration.
CAUTION
Avoid touching the screen at all times, as this
yy
may result in damage to the screen.
yy It is recommended to move the TV in the box
or packing material that the TV originally came
in.
yy Before moving or lifting the TV, disconnect the
power cord and all cables.
yy When holding the TV, the screen should face
away from you to avoid damage.
yy When transporting the TV, do not expose the
TV to jolts or excessive vibration.
yy When transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
yy Hold the top and bottom of the TV frame firmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
ASSEMBLING AND PREPARING
9
ENGLISH
ENG
Setting up the TV
Image shown may differ from your TV.
Attaching the stand
Only 22/26LT36**
1
M4 x 12
3
4 EA
Stand Body
M4X20
Front
Stand Base
Top View
M4 x 16
2 EA
(Only 22LT36**)
2
M4 x 12
4 EA
(Only 26LT36**)
10
ASSEMBLING AND PREPARING
ENG
ENGLISH
Only 32/37/42/47LT36**
1
3
M4 x 14
4 EA
Stand Body
M4X20
Front
Stand Base
Top View
M4 x 14
2
4 EA
CAUTION
When attaching the stand to the TV
yy
set, place the screen facing down on a
cushioned table or flat surface to protect
the screen from scratches.
Make sure that the screws are inserted
yy
correctly and fastened securely. If they are
not fastened securely enough, the TV may
tilt forward after being installed. Do not use
too much force and over tighten the screws;
otherwise screw may be damaged and not
tighten correctly.
NOTE
Remove the stand before installing the
yy
TV on a wall mount by performing the
stand attachment in reverse.
ASSEMBLING AND PREPARING
Securing the TV to a table
1 Lift and tilt the TV into its upright position on a
table.
-Leave a 10 cm (minimum) space from the
wall for proper ventilation.
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
Mount the TV on a table, and then insert and
tighten the supplied screw on the rear of the stand.
Only 32/37/42/47LT36**
2 Connect the power cord to a wall outlet.
CAUTION
WARNING
Do not place the TV near or on sources
yy
of heat, as this may result in fire or other
damage.
To prevent TV from falling over, the TV
yy
should be securely attached to the floor/
wall per installation instructions. Tipping,
shaking, or rocking the TV may cause injury.
Attaching the TV to a table
Image shown may differ from your TV.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially
causing injury or damaging the pro duct.
(Only 32/37/42/47LT36**)
Adjusting the angle of the TV to suit view
Swivel 90 degrees to the left or right and adjust the
angle of the TV to suit your view.
90
4-Screws
(not provided as parts of the product)
Stand
90
CAUTION
When adjusting the angle of the product,
yy
watch out for your fingers.
»» Personal injury may occur if hands or
fingers are pinched. If the product is tilted
too much, it may fall, causing damage or
injury.
Table
Screws: M4 x L (*L: Table depth + 8-10 mm)
ex) Table depth: 15mm, Screw: M4 x 20
ENGLISH
ENG
Mounting on a table
11
12
ASSEMBLING AND PREPARING
ENG
ENGLISH
Securing the TV to a wall
(This feature is not available for all models.)
Mounting on a wall
Attach an optional wall mount bracket at the rear of
the TV carefully and install the wall mount bracket
on a solid wall perpendicular to the floor. When you
attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
1 Insert and tighten the eye-bolts, or TV brackets
2
3
and bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
Make sure that children do not climb on or
yy
hang on the TV.
NOTE
Use a platform or cabinet that is strong and
yy
large enough to support the TV securely.
Brackets, bolts and ropes are not provided.
yy
You can obtain additional accessories from
your local dealer.
ASSEMBLING AND PREPARING
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in
the following table.
Model
22/26LT36**
32LT36**
VESA
Standard screw
Number of screws
Wall mount
bracket
100 x 100
M4
4
LSW100B(G)
200 x 100
M4
4
Model
37/42LT36**
37/42LT36**
VESA
Standard screw
Number of screws
Wall mount
bracket
200 x 200
M6
4
LSW200BX(G)
200 x 200
M6
4
LSW220BX(G)
Model
47LT36**
47LT36**
VESA
400 x 400
400 x 400
Standard screw
M6
M6
Number of screws 4
4
Wall mount
bracket
LSW420BX(G)
LSW400BX(G)
CAUTION
Disconnect the power first, and then move
yy
or install the TV. Otherwise electric shock
may occur.
If you install the TV on a ceiling or slanted
yy
wall, it may fall and result in severe injury.
Use an authorized LG wall mount bracket
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
yy
cause damage to the TV and void your
warranty.
Use the screws and wall mount bracket that
yy
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
On the 47 inch models, use M6 x L45
yy
screws.
NOTE
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The wall mount bracket is not provided. You
yy
can obtain additional accessories from your
local dealer.
The length of screws may differ depending
yy
on the wall mount. Make sure to use the
proper length.
For more information, refer to the manual
yy
supplied with the wall mount.
Not using the DESK-TYPE STAND
A
B
(Only 32/37/42/47LT36**)
Image shown may differ from your TV.
When installing the wall-mounted bracket, use the
protection cover.
Insert the Protection cover into the TV until
clicking sound.
Protection cover
ENGLISH
ENG
Separate purchase (Wall Mounting Bracket)
13
14
ASSEMBLING AND PREPARING
ENG
ENGLISH
Tidying cables
Only 32/37/42/47LT36**
1 Install the Power Cord Holder and Power Cord.
It will help prevent the power cable from being
removed by accident.
Power Cord Holder
2 Gather and bind the cables with the Cable
Holder.
Cable Holder
Only 22/26LT36**
1 Gather and bind the cables with the Cable
Holder.
Cable Holder
CAUTION
Do not move the TV by holding the Cable
yy
Holder and Power Cord Holder, as the
Cable holders may break, and injuries and
damage to the TV may occur.
MAKING CONNECTIONS
This section on MAKING CONNECTIONS mainly
uses diagrams for the LT36** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information on external device’s
connection, refer to the manual provided with each
device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
NOTE
The external device connection may differ
yy
from the model.
Connect external devices to the TV
yy
regardless of the order of the TV port.
If you record a TV program on a DVD
yy
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
on recording, refer to the manual provided
with the connected device.
Refer to the external equipment’s manual for
yy
operating instructions.
If you connect a gaming device to the TV,
yy
use the cable supplied with the gaming
device.
In PC mode, there may be noise associated
yy
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE
menu until the picture is clear.
In PC mode, some resolution settings may
yy
not work properly depending on the graphics
card.
Adapter connection
ENGLISH
ENG
MAKING
CONNECTIONS
15
Only 22/26LT36**
DC IN
DC Adapter
1 Connect the antenna cable to the antenna
input port on the TV.
2 Connect the DC adapter plug to the power
input jack on the TV.
3 Connect the power cord to the DC adapter
first, then plug the power cord into the wall
power outlet.
Antenna connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
ANTENNA
IN
NOTE
Use a signal splitter to use more than 2 TVs.
yy
If the image quality is poor, install a signal
yy
amplifier properly to improve the image
quality.
If the image quality is poor with an antenna
yy
connected, try to realign the antenna in the
correct direction.
An antenna cable and converter are not
yy
supplied.
16
MAKING CONNECTIONS
DVI to HDMI connection
Transmits the digital video and audio signals from
your PC to the TV. Connect the PC and the TV
with the HDMI cable as shown. Choose any HDMI
input port to connect. It does not matter which port
you use.
Transmits the digital video signal from an external
device to the TV. Connect the external device and
the TV with the DVI-HDMI cable as shown. To
transmit an audio signal, connect an audio cable.
Choose any HDMI input port to connect. It does
not matter which port you use.
IN 3
ENG
ENGLISH
HDMI connection
2
VIDEO
R
2
L
L/MONO AUDIO R
1
AUDIO IN
(RGB/DVI
/COMPONENT)
1
2
(*Not Provided)
HDMI
DVI OUT
AUDIO OUT
NOTE
It is recommended to use the TV with the
yy
HDMI connection for the best image quality.
Use the latest High Speed HDMI™ Cable
yy
with CEC (Customer Electronics Control)
function.
High Speed HDMI™ Cables are tested to
yy
carry an HD signal up to 1080p and higher.
Supported DTV Audio: MPEG, Dolby Digital,
yy
Dolby Digital Plus, HE-AAC
Supported HDMI Audio format : Dolby
yy
Digital, PCM (Up to 192 KHz, 32k/44.1k/48k
/88k/96k/176k/192k, DTS Not supported.)
NOTE
yyDepending on the graphics card, DOS mode
may not work if a HDMI to DVI Cable is in use.
MAKING CONNECTIONS
17
Component connection
Transmits the video signal from PC to the TV. To
transmit an audio signal, connect an audio cable.
Transmits the analogue video and audio signals
from an external device to the TV. Connect the
external device and the TV with the component
cable as shown.
2
WHITE
R
USB IN
L
AUDIO IN
(*Not Provided)
2
(RGB/DVI
/COMPONENT)
VIDEO
(*Not Provided)
GREEN
IN 3
L/MONO AUDIO R
RGB IN (PC)
COMPONENT
IN
VIDEO
YELLOW
LL
RED
R
R
L/MONO AUDIO R
WHITE
BLUE
RED
BLUE
AUDIO OUT
RS-232C Setup
(*Not
Provided)
(*Not Provided)
R
AUDIO
VIDEO
RS-232C IN
(CONTROL & SERVICE)
Blu-Ray / HD Cable Box / DVD
NOTE
(*Not Provided)
If cables are installed incorrectly, it could
yy
cause the image to display in black and
white or with distorted colour.
GREEN
BLUE
L
RED
WHITE
RED
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an
A/V control system) to control the product’s
functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied
with the product.
GREEN
RED
RGB OUT (PC)
PC
GREEN
AUDIO IN
(RGB/DVI
/COMPONENT)
ENGLISH
ENG
RGB-PC connection
18
MAKING CONNECTIONS
Speaker output SETUP
Transmits analog video and audio signals from an
external device to the TV. Connect the external
device and the TV with th e composite cable as
shown.
Connect the external speaker to the SPEAKER
IN (PC)
OUTPUT(STEREO)RGB
jack
on the TV.2
DC IN
RS-232C IN
L
ANTENNA
IN
R
EXTERNAL
SPEAKER OUT
L/MONO AUDIO
O R
(CONTROL & SERVICE)
VIDEO
AUDIO IN
1
2
2
RR+
VIDEO
YELLOW
L
RED
R
L/MONO AUDIO R
LL+
WHITE
USB connection
AUDIO IN
(RGB/DVI
/COMPONENT)
Connect a USB storage device such as s USB
flash memory, external hard drive or a USB
memory card reader to the TV and access the My
media menu to use various multimedia files.
(*Not Provided)
RED
WHITE
YELLOW
VIDEO
USB IN
ENG
ENGLISH
Composite connection
L (MONO) AUDIO R
USB device
VCR / DVD / Blu-Ray / HD Cable Box
(*Not Provided)
MAKING CONNECTIONS
▼PCMCIA CARD SLOT▼
Euro Scart connection
Transmits the video and audio signals from an
external device to the TV set. Connect the external
device and the TV set with the euro scart cable as
shown. To display images by using progressive
scan, make sure to use the euro scart cable.
(*Not Provided)
View the encrypted (pay) services in digital TV
mode. This feature is not available in all countries.
NOTE
yyCheck if the CI module is inserted into the
PCMCIA card slot in the right direction. If the
module is not inserted properly, this can cause
damage to the TV and the PCMCIA card slot.
Current
input model
Output
Type
AV
(TV Out1)
Digital TV
Digital TV
Analogue TV, AV
Analogue TV
Component / RGB
Analogue TV
HDMI
Analogue TV
1. TV Out : Outputs Analogue TV or Digital TV signals.
NOTE
Any Euro scart cable used must be signal
yy
shielded.
ENGLISH
ENG
CI module connection
19
20
REMOTE CONTROL
ENG
ENGLISH
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching
the
and
ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
Do not mix old and new batteries, as this may damage the remote control.
yy
Make sure to point the remote control toward the remote control sensor on the TV.
ENERGY SAVING
Adjusts the brightness of the screen to
reduce energy consumption.
(Back)
Returns to the previous level.
ENERGY
TV/RAD
SAVING
POWER
Turns the TV on or off.
EXIT
Clears on-screen displays and return to
TV viewing.
TV/RAD
Selects Radio, TV and DTV programme.
Adjusts the volume level.
GUIDE
Shows programme guide.
FAV
Accesses your favourite programme list.
INFO
Views the information of the current
programme and screen.
RATIO
Resizes an image.
GUIDE
INFO
RATIO
AV MODE
LIST
AD
Switches the Audio Description On or Off.
Q.VIEW
Q.MENU
SETTINGS
Number
buttons
BACK
Enters numbers.
LIST
MARK
Accesses
the saved programme list.
Q.VIEW
Returns to the previously viewed
programme.
EXIT
FAV
3
5
6
8
9
7
0
MARK
FAV
P
A
G
E
MUTE
AD
P
MUTE
: Green,
: Yellow,
SUBTITLE
Recalls your preferred subtitle in digital
mode.
1 TELETEXT BUTTONS
These buttons are used for teletext.
AD
:
Control buttons (
)
Controls the MY MEDIA menus, or
the SIMPLINK compatible devices
(USB,SIMPLINK).
1
OK
PAGE
Moves to the previous or next screen.
(
: Red,
Blue)
P
A
G
E
Q. MENU
Accesses the quick menus.
OK
Selects menus or options and confirms
your input.
2
MUTE
Mutes all sounds.
Colour buttons
These access special functions in some
menus.
SETTINGS
Accesses the main menus.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
1
4
P
Scrolls through the saved programmes.
INPUT
Changes the input source.
INPUT
PR
MAINTENANCE / TROUBLESHOOTING
21
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
Make sure to turn the power off and disconnect the power cord and all other cables first.
yy
When the TV is left unattended and unused for a long time, disconnect the power cord from the wall
yy
outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
Avoid touching the screen at all times, as this may result in damage to the screen.
yy
Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in
yy
scratches and image distortions.
Do not use any chemicals as this may damage the product.
yy
Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
yy
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem
Solution
Cannot control the
TV with the remote
control.
Check the remote control sensor on the product and try again.
yy
Check if there is any obstacle between the product and the remote control.
yy
Check if the batteries are still working and properly installed (
to , to ).
yy
No image display
and no sound is
produced.
Check if the product is turned on.
yy
Check if the power cord is connected to a wall outlet.
yy
Check if there is a problem in the wall outlet by connecting other products.
yy
The TV turns off
suddenly.
Check the power control settings. The power supply may be interrupted.
yy
Check if the Auto sleep feature is activated in the Time settings.
yy
If there is no signal while the TV is on, the TV will turn off automatically after
yy
15 minutes of inactivity.
When connecting to
the PC (RGB/HDMI
DVI), ‘No signal’ or
‘Invalid Format’ is
displayed.
Turn the TV off/on using the remote control.
yy
Reconnect the RGB/HDMI cable.
yy
Restart the PC with the TV on.
yy
ENGLISH
ENG
MAINTENANCE
22
SPECIFICATIONS
ENG
ENGLISH
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
MODELS
22LT36**
26LT36**
22LT360C-ZA
26LT360C-ZA
Dimensions
(W x H x D)
With stand
517.0 mm x 386.0 mm x 192.0 mm
626.0 mm x 454.0 mm x 192.0 mm
Without stand
517.0 mm x 332.0 mm x 41.6 mm
626.0 mm x 393.0 mm x 46.6 mm
Weight
With stand
3.7 kg
Without stand
3.1 kg
4.1 kg
DC 24 V, 1.4 A
DC 24 V, 1.8 A
Power requirement
4.7 kg
AC-DC adaptor : 24 V
Power consumption
MODELS
, 2.5 A / AC 100-240 V~ 50 / 60 Hz
32LT36**
37LT36**
32LT360C-ZA
37LT360C-ZA
Dimensions
(W x H x D)
With stand
766.0 mm x 536.0 mm x 231.9 mm
867.0 mm x 593.0 mm x 231.9 mm
Without stand
766.0 mm x 476.0 mm x 68.5 mm
867.0 mm x 533.0 mm x 68.6mm
Weight
With stand
9.2 kg
Without stand
8.0 kg
Power requirement
11.2Kg
10.0Kg
AC 100-240 V~ 50 / 60 Hz
Power consumption
MODELS
60W
90W
42LT36**
47LT36**
42LT360C-ZA
47LT360C-ZA
Dimensions
(W x H x D)
With stand
992.0 mm x 667.0 mm x 273.1 mm
1101.0 mm x 729.0 mm x 273.1 mm
Without stand
992.0 mm x 604.0 mm x 55.0 mm
1101.0 mm x 665.0 mm x 54.5 mm
Weight
With stand
15.5 kg
17.3Kg
Without stand
13.5 kg
15.3Kg
Power requirement
Power consumption
CI Module Size
(W x H x D)
Environment
condition
AC 100-240 V~ 50 / 60 Hz
120W
100W
100.0 mm x 55.0 mm x 5.0 mm
Operating
Temperature
Operating Humidity
0 °C to 40 °C
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
SPECIFICATIONS
Analogue TV
DVB-T
PAL/SECAM B/G/D/K,
DVB-C
SECAM L/L’
Television System
Programme Coverage
VHF, UHF
VHF: E2 to E12, UHF: E21 to E69,
CATV: S1 to S20, HYPER: S21 to S47
Maximum number of storable
programmes
1,086
External Antenna Impedance
75 Ω
RGB-PC, HDMI/DVI-PC supported mode
Component port connecting information
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x400
31.468
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x720
45
60
1280x768
47.78
59.87
1360x768
47.72
59.80
1280x1024
63.981
60.02
1920x1080
(RGB-PC)
66.587
59.93
1920x1080
(HDMI-PC)
67.5
60.00
(Except for 22/26/32LT36**)
HDMI/DVI-DTV supported mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x480
31.469
31.5
59.94
60
720x576
31.25
50
1280x720
37.5
44.96
45
50
59.94
60
1920x1080
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.43
67.5
59.94
60
50
23.97
24
29.976
30.00
50
59.94
60
Component ports on the
TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
ENGLISH
ENG
Digital TV
23
24
IR CODES
ENG
ENGLISH
IR CODES
This feature is not available for all models.
yy
Code
(Hexa)
Function
08
(POWER)
Note
Remote control Button (Power On/Off)
95
ENERGY SAVING
Remote control Button
0B
INPUT
Remote control Button
F0
TV/RAD
Remote control Button
10-19
Number Key 0-9
Remote control Button
53
LIST
Remote control Button
1A
Q.VIEW
Remote control Button
02
+
Remote control Button
03
-
Remote control Button
1E
FAV
Remote control Button
79
RATIO
Remote control Button
09
MUTE
Remote control Button
00
P+
Remote control Button
01
P-
Remote control Button
43
SETTINGS
Remote control Button
AB
GUIDE
Remote control Button
45
Q.MENU
Remote control Button
AA
INFO
Remote control Button
28
BACK
Remote control Button
5B
EXIT
Remote control Button
44
OK
Remote control Button
40
Remote control Button
41
^
v
07
<
Remote control Button
06
>
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
20
TEXT
Remote control Button
21
T.OPT(T.Option)
Remote control Button
39
SUBTITLE
Remote control Button
B1
n
Remote control Button
B0
►
Remote control Button
BA
yy
Remote control Button
8E
►►
Remote control Button
8F
◄◄
Remote control Button
91
AD
Remote control Button
Remote control Button
EXTERNAL CONTROL DEVICE SETUP
25
RS-232C Setup
RS-232C Configurations
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an
A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied
with the product.
RGB IN (PC)
L
7-Wire Configurations (Standard RS-232C cable)
RXD TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
ANTENNA
IN
R
2
R
1
L/MONO AUDIO R
EXTERNAL
SPEAKER OUT
2
VIDEO
RS-232C IN
(CONTROL & SERVICE)
ENGLISH
ENG
EXTERNAL CONTROL DEVICE SETUP
AUDIO IN
/COMPONENT)
3-Wire Configurations(Not standard)
Type of connector;
D-Sub 9-Pin Male
1
RXD TXD
GND
DTR
DSR
RTS
CTS
5
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Set ID number. "Real Data Mapping".
1 Press SETTINGS to access the main menus.
2 Press the Navigation buttons to scroll to
6
No.
9
Pin name
1
3.5V
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
No Connection
8
No Connection
9
No Connection (12V available in some models)
OPTION and press OK.
3 Press the Navigation buttons to scroll to SET
ID and press OK.
4 Scroll left or right to select a set ID number and
select CLOSE. The adjustment range is 1-99.
5 When you are finished, press EXIT.
26
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
Communication Parameters
yy Baud rate: 9600 bps (UART)
yy Data length: 8 bits
yy Parity : None
yy Stop bit: 1 bit
yy Communication code: ASCII code
yy Use a crossed (reverse) cable.
Command reference list
(Depending on model)
01. Power
02. Aspect
Ratio
03. Screen
Mute
04. Volume
Mute
05. Volume
Control
k
a
DATA
(Hexadecimal)
00 to 01
k
c
(See p.28)
14. Bass
k
s
00 to 64
k
d
(See p.28)
15. Balance
k
t
00 to 64
k
e
00 to 01
x
u
00 to 64
k
f
00 to 64
j
q
00 to 05
06. Contrast
k
g
00 to 64
j
u
01
07. Brightness
k
h
00 to 64
m
a
(See p.30)
08. Colour
k
i
00 to 64
m
b
00 to 01
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 64
m
m
c
g
Key Code
00 to 64
11. OSD Select k
l
00 to 01
x
b
(See p.31)
12. Remote
Control
Lock Mode
m
00 to 01
COMMAND1
k
COMMAND2
13. Treble
k
r
DATA
(Hexadecimal)
00 to 64
COMMAND1
16. Colour
Temperature
17. Energy
Saving
18. Auto Configuration
19. Tune Command
20. Programme
Add/Skip
21. Key
22. Control
Back Light
23. Input select
(Main)
COMMAND2
yy * Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are
not executed and treated as NG.
EXTERNAL CONTROL DEVICE SETUP
27
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]
[Command 2]
[Set ID]
: First command to control the TV.(j, k, m or x)
: Second command to control the TV.
: You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment
range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ]
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data00: Illegal Code
ENGLISH
ENG
Transmission / Receiving Protocol
28
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
01. Power (Command: k a)
04. Volume Mute (Command: k e)
►► To control Power On/Off of the set.
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on remote
control.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data based on this
format, Acknowledgement data feed back presents status
about each function.
* OK Ack., Error Ack. and other message may display on the
screen when TV is power On.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
02. Aspect Ratio (Command: k c) (Main Picture
Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the Aspect
Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen
(16:9)
04 : Zoom
06 : Original
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect
ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p
24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i,
1080p 50 Hz / 60 Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital, Analogue, AV.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 :
01 :
10 :
Screen mute off (Picture on)
Video mute off
Screen mute on (Picture off)
Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen
Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
13. Treble (Command: k r)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
►► To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
14. Bass (Command: k s)
►► To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling
remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
15. Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and remote
control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
16. Colour Temperature (Command: x u)
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this mode.
When main power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by
power on key of IR & Local Key.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.31.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
09. Tint (Command: k j)
29
30
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
17. Energy Saving (Command: j q)
19. Tune Command (Command: m a)
►► To reduce the power consumption of the TV. You can also
adjust Energy Saving in PICTURE menu.
►► Select channel to following physical number.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function
7
6
5
4
0
0
0
0
0
0
0
0
0
0
Level
Description
3
2
1
0
Low
Power
0
0
0
0
Off
0
Low
Power
0
0
0
1
Minimum
0
0
Low
Power
0
0
1
0
Medium
0
0
0
Low
Power
0
0
1
1
Maximum
0
0
0
0
Low
Power
0
1
0
1
Screen Off
0
0
0
0
Low
Power
0
1
0
0
Auto
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data00 :High channel data
Data01 :Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 :[Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 to Max: 7DH
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
20. Programme Add/Skip(Command: m b)
18. Auto Configure(Command: j u)
►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
►► To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
Data 01: To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
21. Key(Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - See p.24.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
22. Control Back Light(Command: m g)
►► To control the back light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
31
23. Input select (Command: x b)
ENGLISH
ENG
(Main Picture Input)
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
LSB
0
0
0
0
0
0
External Input
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping
00 : Step 0
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E : Step 110
73 :
74 :
Step 115
Step 116
CF : Step 199
FE : Step 254
FF : Step 255
0
The model and serial numbers of the TV is
located on the back of the TV
Record it below should you ever need
service.
Model
Serial
Download PDF