LG | 28LP531H | LG 28LP531H Owner’s Manual

OWNER’S MANUAL
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain it
for future reference.
LP53**
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
LICENSES
21 SPECIFICATIONS
3
OPEN SOURCE SOFTWARE
NOTICE
23 IR CODES
4
INSTALLATION PROCEDURE
4
ASSEMBLING AND
PREPARING
4
7
8
9
9
9
10
11
12
Unpacking
Parts and buttons
Lifting and moving the TV
Setting up the TV
- Attaching the stand
- Detaching the Stand
- Mounting on a table
- Mounting on a wall
- Tidying cables
24 EXTERNAL CONTROL DEVICE
SETUP
24 RS-232C setup
24 Type of connector:
D-Sub 9-Pin Male
24 RS-232C configurations
25 Communication parameters
25 Command reference list
26 Transmission / Receiving Protocol
13 MAKING CONNECTIONS
13
14
14
15
15
16
16
17
17
18
Antenna connection
Adapter connection
HDMI connection
DVI to HDMI connection
RGB-PC connection
Component connection
USB connection
Headphone connection
CI module connection
Euro Scart connection
19 REMOTE CONTROL
20 MAINTENANCE
20 Cleaning your TV
20 - Screen, frame, cabinet and stand
20 - Power cord
20 TROUBLESHOOTING
WARNING
If you ignore the warning message, you may
yy
be seriously injured or there is a possibility
of accident or death.
CAUTION
If you ignore the caution message, you may
yy
be slightly injured or the product may be
damaged.
NOTE
The note helps you understand and use
yy
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and
other countries.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274
OPENSOURCESOFTWARENOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
ENGLISH
ENG
LICENSES
4
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
Image shown may differ from your TV.
yy
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy
The available menus and options may differ from the input source or product model that you are
yy
using.
New features may be added to this TV in the future.
yy
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
yy
be turned off if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the picture
yy
is reduced, and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy
Some models have a thin film attached on to the screen and this must not be removed.
yy
NOTE
The items supplied with your product may vary depending on the model.
yy
Product specifications or contents of this manual may be changed without prior notice due to upgrade
yy
of product functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
yy
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory
stick does not fit into your TV’s USB port.
B
A
*A 10 mm
B
*B 18 mm
A
ASSEMBLING AND PREPARING
ENGLISH
ENG
ENERGY AV MODE INPUT
TV
SAVING
1
2
3
4
5
6
7
8
9
0
FLASHBK
LIST
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
Owner’s manual
Remote control,
Batteries (AAA)
(See p.19)
Cable Holder
(Depending on model)
(See p.12)
Power cord
(Depending on model)
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
or
Stand base
(See p.9)
AC-DC Adaptor
(Depending on model &
country)
(See p.14)
5
Isolator
(Depending on model)
(See p.6)
6
ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
Antenna Isolator Installation Guide
yy
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND of
antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact
might be heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall,
mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
2. Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection
to a cable distribution system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING
ENGLISH
ENG
Parts and buttons
Screen
Speakers
Remote Control Sensor
Touch Buttons1
Touch Buttons
7
Description
Scrolls through the saved programmes.
Adjusts the volume level.
OK ꔉ
Selects the highlighted menu option or confirms an input.
SETTINGS
Accesses the main menu, or saves your input and exits the menus.
INPUT
Changes the input source.
/I
Turns the power on or off.
1 All of the buttons are touch sensitive and can be operated through simple touch with your finger.
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
When transporting a large TV, there should
yy
be at least 2 people.
When transporting the TV by hand, hold the
yy
TV as shown in the following illustration.
CAUTION
Avoid touching the screen at all times, as this
yy
may result in damage to the screen.
It is recommended to move the TV in the
yy
box or packing material that the TV originally
came in.
Before moving or lifting the TV, disconnect
yy
the power cord and all cables.
When holding the TV, the screen should face
yy
away from you to avoid damage.
Hold the top and bottom of the TV frame
yy
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
When transporting the TV, do not expose the
yy
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
yy
upright, never turn the TV on its side or tilt
towards the left or right.
Do not apply excessive pressure to cause
yy
flexing / bending of frame chassis as it may
damage screen.
ASSEMBLING AND PREPARING
ENGLISH
ENG
Setting up the TV
Image shown may differ from your TV.
Attaching the stand
1
Detaching the Stand
1
Stand Base
Stand Base
2
2
CAUTION
When attaching the stand to the TV, place
yy
the screen facing down on a cushioned table
or flat surface to protect the screen from
scratches.
9
NOTE
When Detaching the stand from TV, Detach
yy
the stand with lifting up the lever in the
direction of the arrow.
10
ASSEMBLING AND PREPARING
ENG
ENGLISH
Mounting on a table
Using the Kensington security system
(Depending on model)
1 Lift and tilt the TV into its upright position on a
table.
-- Leave a 10 cm (minimum) space from the
wall for proper ventilation.
Connect the Kensington security system cable
between the TV and a table.
10 cm
10 cm
The Kensington security system connector is
located at the rear of the TV. For more information
of installation and using, refer to the manual
provided with the Kensington security system or
visit http://www.kensington.com.
10 cm
10 cm
2 Connect the AC-DC Adapter and Power Cord
to a wall outlet.
CAUTION
Do not place the TV near or on sources
yy
of heat, as this may result in fire or other
damage.
ASSEMBLING AND PREPARING
(This feature is not available for all models.)
Mounting on a wall
Attach an optional wall mount bracket at the rear of
the TV carefully and install the wall mount bracket
on a solid wall perpendicular to the floor. When you
attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm
1010cm
cm
10 cm
1 Insert and tighten the eye-bolts, or TV brackets
2
3
and bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
Make sure that children do not climb on or
yy
hang on the TV.
NOTE
Use a platform or cabinet that is strong and
yy
large enough to support the TV securely.
Brackets, bolts and ropes are not provided.
yy
You can obtain additional accessories from
your local dealer.
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in
the following table.
Separate purchase(Wall Mounting Bracket)
Model
VESA (A x B)
Standard screw
Number of screws
Wall mount bracket
28LP53**
100 x 100
M4
4
LSW130B
ENGLISH
ENG
Securing the TV to a wall
11
12
ASSEMBLING AND PREPARING
ENG
ENGLISH
CAUTION
Disconnect the power first, and then move
yy
or install the TV. Otherwise electric shock
may occur.
If you install the TV on a ceiling or slanted
yy
wall, it may fall and result in severe injury.
Use an authorized LG wall mount and
contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
yy
cause damage to the TV and void your
warranty.
Use the screws and wall mounts that meet
yy
the VESA standard. Any damages or injuries
by misuse or using an improper accessory
are not covered by the warranty.
Tidying cables
Gather and bind the cables with the cable holder.
Cable Holder
NOTE
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The wall mount bracket is not provided. You
yy
can obtain additional accessories from your
local dealer.
The length of screws may differ depending
yy
on the wall mount. Make sure to use the
proper length.
For more information, refer to the manual
yy
supplied with the wall mount.
CAUTION
yy Do not move the TV by holding the cable
holder, as the cable holders may break, and
injuries and damage to the TV may occur.
MAKING CONNECTIONS
Antenna connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
This section on MAKING CONNECTIONS mainly
uses diagrams for the LP53** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information on external device’s
connection, refer to the manual provided with each
device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
ANTENNA
/CABLE IN
NOTE
The external device connection may differ
yy
from the model.
Connect external devices to the TV
yy
regardless of the order of the TV port.
If you record a TV program on a DVD
yy
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
on recording, refer to the manual provided
with the connected device.
Refer to the external equipment’s manual for
yy
operating instructions.
If you connect a gaming device to the TV,
yy
use the cable supplied with the gaming
device.
In PC mode, there may be noise associated
yy
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE
menu until the picture is clear.
In PC mode, some resolution settings may
yy
not work properly depending on the graphics
card.
(*Not
Provided)
NOTE
Use a signal splitter to use more than 2 TVs.
yy
If the image quality is poor, install a signal
yy
amplifier properly to improve the image
quality.
If the image quality is poor with an antenna
yy
connected, try to realign the antenna in the
correct direction.
An antenna cable and converter are not
yy
supplied.
Supported DTV Audio: MPEG, Dolby Digital,
yy
Dolby Digital Plus, HE-AAC
ENGLISH
ENG
MAKING
CONNECTIONS
13
14
MAKING CONNECTIONS
ENG
ENGLISH
Adapter connection
HDMI connection
Transmits the digital video and audio signals from
an external device to the TV. Connect the external
device and the TV with the HDMI cable as shown.
DC-IN
AC-DC Adapter
HDMI IN
1 Connect the antenna cable to the antenna
input port on the TV.
2 Connect the DC adapter plug to the power
input jack on the TV.
3 Connect the power cord to the DC adapter first,
DVD / Blu-Ray
/ HD Cable Box
/ PC
then plug the power cord into the wall power
outlet.
(*Not
Provided)
CAUTION
Please be sure to connect the TV to the ACyy
DC power adapter before connecting the
TV’s power plug to a wall power outlet.
HDMI
NOTE
It is recommended to use the TV with the
yy
HDMI connection for the best image quality.
Use the latest High Speed HDMI™ Cable
yy
with CEC (Customer Electronics Control)
function.
High Speed HDMI™ Cables are tested to
yy
carry an HD signal up to 1080p and higher.
Supported HDMI Audio format : Dolby
yy
Digital, PCM (Up to 192 KHz, 32KHz/44.1KHz
/48KHz/88KHz/96KHz/176KHz/192KHz)
※ DTS Not supported.
MAKING CONNECTIONS
15
RGB-PC connection
Transmits the digital video signal from an external
device to the TV. Connect the external device and
the TV with the HDMI to DVI cable as shown. To
transmit an audio signal, connect an audio cable.
Transmits the video signal from PC to the TV. To
transmit an audio signal, connect an audio cable.
RGB IN (PC)
AUDIO IN
(COMPONENT/RGB/DVI)
HDMI IN
AUDIO IN
(COMPONENT/RGB/DVI)
(*Not Provided)
(*Not
Provided)
(*Not
Provided)
RGB (PC)
DVI
AUDIO
AUDIO
DVD / Blu-Ray / HD Cable Box / PC
NOTE
Depending on the graphics card, DOS mode
yy
may not work if a HDMI to DVI Cable is in
use.
When using the HDMI/DVI cable, only Single
yy
link is supported.
PC
ENGLISH
ENG
DVI to HDMI connection
16
MAKING CONNECTIONS
ENG
ENGLISH
Component connection
USB connection
Transmits the analogue video and audio signals
from an external device to the TV. Connect the
external device and the TV with the component
cable as shown.
Connect a USB storage device such as s USB
flash memory, external hard drive or a USB
memory card reader to the TV and access the My
media menu to use various multimedia files.
COMPONENT
IN
USB
AUDIO IN
(COMPONENT/RGB/DVI)
(*Not Provided)
(*Not Provided)
RED
BLUE
RED
GREEN
BLUE
GREEN
(*Not Provided)
(*Not Provided)
RED
BLUE
GREEN
RED
WHITE
L
R
AUDIO
VIDEO
OPTICAL
DIGITAL
AUDIO OUT
DVD / Blu-Ray / HD Cable Box
NOTE
If cables are not installed correctly, it could
yy
cause this image to display in black and
white or with distorted colours.
SPEAKER
OUT
AUDIO IN
(RGB/DVI)
RGB IN (PC)
VOLUME
CONTROL
RS-232C IN
(CONTROL & SERVICE)
STEREO
(8 )
1
2
MAKING CONNECTIONS
17
Transmits the headphone signal from the TV to an
external device. Connect the external device and
the TV with the headphone as shown.
View the encrypted (pay) services in digital TV
mode. This feature is not available in all countries.
PCMCIA
CARD SLOT
CI module connection
H/P
(*Not Provided)
(*Not Provided)
NOTE
PCMCIA
CARD SLOT
AUDIO menu items are disabled when
yy
connecting a headphone.
Headphone impedance: 16
yy
Max audio output of headphone: 9 mW to
yy
15 mW
Headphone jack size: 0.35 cm
yy
NOTE
Check if the CI module is inserted into the
yy
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to the TV and the PCMCIA
card slot.
ENGLISH
ENG
Headphone connection
18
MAKING CONNECTIONS
ENG
ENGLISH
Euro Scart connection
Transmits the video and audio signals from an
external device to the TV set. Connect the external
device and the TV set with the euro scart cable as
shown.
(*Not Provided)
AUDIO / VIDEO
Output
Type
Current
input mode
Digital TV
Analogue TV
Component, AV, HDMI, RGB
AV1
(TV Out1)
Digital TV
Analogue TV
1 TV Out : Outputs Analogue TV or Digital TV
signals.
NOTE
Any Euro scart cable used must be signal
yy
shielded.
REMOTE CONTROL
19
ENGLISH
ENG
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching
the
and
ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
Do not mix old and new batteries, as this may damage the remote control.
yy
Make sure to point the remote control toward the remote control sensor on the TV.
Turns the TV on or off.
ENERGY
AV MODE
Number buttons
Enters numbers.
INPUT
SAVING
AV MODE
Selects an AV mode.
INPUT
Changes the input source.
TV/RAD
Selects Radio, TV and DTV programme.
GUIDE
Shows programme guide.
1
2
3
Q.VIEW
Returns to the previously viewed programme.
4
5
6
Adjusts the volume level.
7
8
9
FAV
Accesses your favourite programme list.
LIST
0
Q.VIEW
RATIO
INFO
Views the information of the current
programme and screen.
MUTE
Mutes all sounds.
P
MUTE
GUIDE PORTAL INFO
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
OK
Selects menus or options and confirms
your input.
OK
Home
Selects a menu.
Clears all on-screen displays and returns
to TV viewing from any menu.
EXIT
Home
P
A
G
E
ꕍPꕌ
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
GUIDE
Colour buttons
These access special functions in some
menus.
(
: Red,
: Green,
: Yellow,
: Blue)
1 TELETEXT BUTTONS
These buttons are used for teletext.
Returns to the previous level.
Q. MENU
Accesses the quick menus.
RATIO
Resizes an image.
FAV
PORTAL
Displays and removes hotel interactive
EXIT
Clears on-screen displays and return to TV
viewing.
LIST
Accesses the saved programme list.
TV/
RAD
ꕊ ENERGY SAVING
Adjusts the brightness of the screen to
reduce energy consumption.
SUBTITLE
Home
Recalls your preferred subtitle in digital mode.
Control buttons (ꕗ, ꕖ, ꕘ, ꕚ, ꕙ)
Controls the MY MEDIA menus, or
the SIMPLINK compatible devices
(USB,SIMPLINK).
1
Q.MENU
AD
ALARM
SIMPLINK
Accesses the AV devices connected with the
HDMI cable through HDMI-CEC.
Opens the SIMPLINK menu.
AD
Switches the Audio Description On or Off.
ALARM
Sets the alarm function.
(Except for 28LP53**)
PORTAL INFO
OK
BACK
EXIT
20
MAINTENANCE / TROUBLESHOOTING
ENG
ENGLISH
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
Make sure to turn the power off and disconnect the power cord and all other cables first.
yy
When the TV is left unattended and unused for a long time, disconnect the power cord from the wall
yy
outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
Avoid touching the screen at all times, as this may result in damage to the screen.
yy
Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in
yy
scratches and image distortions.
Do not use any chemicals as this may damage the product.
yy
Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
yy
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
The software version can be updated for improvement in performance. Customer needs to ensure the
compatibility of customer’s equipment with LGE software. If needed, please consult with LGE and upload
revised software version according to the guidance provided by LGE.
Problem
Solution
Cannot control the
TV with the remote
control.
Check the remote control sensor on the product and try again.
yy
Check if there is any obstacle between the product and the remote control.
yy
Check if the batteries are still working and properly installed (
to , to ).
yy
No image display
and no sound is
produced.
Check if the product is turned on.
yy
Check if the power cord is connected to a wall outlet.
yy
Check if there is a problem in the wall outlet by connecting other products.
yy
The TV turns off
suddenly.
Check the power control settings. The power supply may be interrupted.
yy
Check if the Auto sleep feature is activated in the Time settings.
yy
When connecting to
the PC (RGB/HDMI
DVI), ‘No signal’ or
‘Invalid Format’ is
displayed.
Turn the TV off/on using the remote control.
yy
Reconnect the RGB/HDMI cable.
yy
Restart the PC with the TV on.
yy
SPECIFICATIONS
21
Product specifications may be changed without prior notice due to upgrade of product functions.
28LP53**
MODELS
Dimensions
(W x H x D)
Weight
28LP531H-ZA
With stand (mm)
645.3 x 447.9 x 182.1
Without stand (mm)
645.3 x 401.6 x 78.7
With stand (kg)
5.1
Without stand (kg)
4.7
Power Consumption
Power requirement
38 W
24 V
AC/DC Adapter
Manufacturer : Ampower
Model : AAH-00
Input : AC 100 – 240 V ~ 50 / 60 Hz
Output : 24 V
2.5 A
1.6 A
CI Module Size
(W x H x D)
Environment
condition
100.0 mm x 55.0 mm x 5.0 mm
Operating
Temperature
0 °C to 40 °C
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Television system
Programme coverage
Maximum number
of storable
programmes
Digital TV
Analogue TV
DVB-T
PAL/SECAM B/G/D/K/I/I',
DVB-C
SECAM L/L’
VHF, UHF
LP53**
External antenna impedance
VHF: E2 to E12, UHF: E21 to E69,
CATV: S1 to S20, HYPER: S21 to S47
1,500
75 Ω
ENGLISH
ENG
SPECIFICATIONS
22
SPECIFICATIONS
ENG
ENGLISH
Component port connecting information
HDMI/DVI-DTV supported mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x480
31.47
31.5
59.94
60
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
720x576
31.25
50
1280x720
37.5
44.96
45
50
59.94
60
1920x1080
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.432
67.5
59.94
60
50
23.976
24
29.976
30.00
50
59.94
60
RGB-PC, HDMI/DVI-PC supported mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x400
31.468
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x720
45
60
1280x768
47.78
59.87
1360x768
47.72
59.80
Component ports on the
TV
Video output ports
on DVD player
Y
PB
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
PR
IR CODES
23
IR CODES
Code (Hexa)
Function
08
(POWER)
Note
Remote control Button (Power On/Off)
95
30
ENERGY SAVING
AV MODE
Remote control Button
Remote control Button
0B
INPUT
Remote control Button
F0
TV/RAD
Remote control Button
10-19
Number Key 0-9
Remote control Button
53
LIST
Remote control Button
1A
Q.VIEW
Remote control Button
02
+
Remote control Button
03
-
Remote control Button
1E
FAV
Remote control Button
79
RATIO
Remote control Button
09
MUTE
Remote control Button
00
Pꕌ
Remote control Button
01
Pꕍ
Remote control Button
43
SETTINGS
Remote control Button
AB
GUIDE
Remote control Button
45
Q.MENU
Remote control Button
AA
INFO
Remote control Button
28
BACK
Remote control Button
5B
EXIT
Remote control Button
44
OK
Remote control Button
40
Remote control Button
41
^
v
07
<
Remote control Button
06
>
Remote control Button
72
RED
Remote control Button
71
GREEN
Remote control Button
63
YELLOW
Remote control Button
61
BLUE
Remote control Button
20
TEXT
Remote control Button
21
T.OPT(T.Option)
Remote control Button
39
SUBTITLE
Remote control Button
B1
n
Remote control Button
B0
Remote control Button
BA
►
yy
8E
►►
Remote control Button
8F
◄◄
Remote control Button
91
AD
Remote control Button
7E
SIMPLINK
Remote control Button
0C
43
E8
PORTAL
HOME
ALARM
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
ENGLISH
ENG
This feature is not available for all models.
yy
24
EXTERNAL CONTROL DEVICE SETUP
EXTERNAL CONTROL DEVICE SETUP
1
2
AUDIO IN
COMPONENT
OPTICAL
(COMPONENT/RGB/DVI) AUDIO OUT
IN
AV
(RGB)
RGB IN (PC)
DEBUG
ANTENNA/
CABLE IN
RS-232C IN
RXD TXD
GND
DTR
DSR
RTS
CTS
USB IN
/DVI IN
IN 3
Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to
control the product’s functions externally.
Connect the serial port of the control device to the RS-232C
jack on the product back panel.
Note: RS-232C connection cables are not supplied with the
product.
PCMCIA CARD SLOT
RS-232C configurations
(SERVICE Only) (CONTROL & SERVICE)
H/P OUT
ENG
ENGLISH
RS-232C setup
(*Not Provided)
RXD TXD
GND
DTR
DSR
RTS
CTS
7-Wire Configurations
(Standard RS-232C cable)
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations
(Not standard)
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Set ID number. "Real Data Mapping".
1 Press SETTINGS or HOME to access the main
Type of connector: D-Sub 9-Pin Male
1
5
menus.
2 Press the Navigation buttons to scroll to
OPTION and press OK.
3 Press the Navigation buttons to scroll to Set ID
and press OK.
4 Scroll left or right to select a set ID number and
6
No.
9
Pin name
1
3.5V
2
RXD (Receive data)
3
TXD (Transmit data)
4
No Connection
5
GND
6
No Connection
7
No Connection
8
No Connection
9
No Connection (12V available in some models)
select Close. The adjustment range is 1-99.
5 When you are finished, press EXIT.
EXTERNAL CONTROL DEVICE SETUP
25
yy
Baud rate: 9600 bps (UART)
yy
Data length: 8 bits
yy
Parity : None
ENGLISH
ENG
Communication parameters
yy
Stop bit: 1 bit
yy
Communication code: ASCII code
yy
Use a crossed (reverse) cable.
Command reference list
(Depending on model)
01. Power
02. Aspect
Ratio
03. Screen
Mute
04. Volume
Mute
05. Volume
Control
k
a
DATA
(Hexadecimal)
00 to 01
k
c
(See p.27)
14. Bass
k
s
00 to 64
k
d
(See p.27)
15. Balance
k
t
00 to 64
k
e
00 to 01
x
u
00 to 64
k
f
00 to 64
j
q
00 to 05
06. Contrast
k
g
00 to 64
j
u
01
07. Brightness
k
h
00 to 64
m
a
(See p.29)
08. Colour
k
i
00 to 64
m
b
00 to 01
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 64
m
m
c
g
Key Code
00 to 64
11. OSD Select k
l
00 to 01
x
b
(See p.30)
12. Remote
Control
Lock Mode
m
00 to 01
COMMAND1
k
COMMAND2
13. Treble
k
r
DATA
(Hexadecimal)
00 to 64
COMMAND1
16. Colour
Temperature
17. Energy
Saving
18. Auto Configuration
19. Tune Command
20. Programme
Add/Skip
21. Key
22. Control
Back Light
23. Input select
(Main)
COMMAND2
* Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are not
executed and treated as NG.
26
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]
[Command 2]
[Set ID]
: First command to control the TV.(j, k, m or x)
: Second command to control the TV.
: You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment
range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ]
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data00: Illegal Code
EXTERNAL CONTROL DEVICE SETUP
27
04. Volume Mute (Command: k e)
►► To control Power On/Off of the set.
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on remote
control.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data based on this
format, Acknowledgement data feed back presents status
about each function.
* OK Ack., Error Ack. and other message may display on the
screen when TV is power On.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
02. Aspect Ratio (Command: k c) (Main Picture
Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the Aspect
Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen
(16:9)
04 : Zoom
06 : Original
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect
ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p
24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i,
1080p 50 Hz / 60 Hz) mode, Just Scan is available.
* Full Wide is supported only for Digital, Analogue, AV.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 :
01 :
10 :
Screen mute off (Picture on)
Video mute off
Screen mute on (Picture off)
Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen
Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
01. Power (Command: k a)
28
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
09. Tint (Command: k j)
13. Treble (Command: k r)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
►► To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
14. Bass (Command: k s)
►► To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling
remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
15. Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and remote
control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
16. Colour Temperature (Command: x u)
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this mode.
When main power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by
power on key of IR & Local Key.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.30.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
19. Tune Command (Command: m a)
►► To reduce the power consumption of the TV. You can also
adjust Energy Saving in PICTURE menu.
►► Select channel to following physical number.
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function
7
6
5
4
0
0
0
0
0
0
0
0
0
0
0
Level
Description
3
2
1
0
Low
Power
0
0
0
0
Off
0
Low
Power
0
0
0
1
Minimum
0
0
Low
Power
0
0
1
0
Medium
0
0
0
Low
Power
0
0
1
1
Maximum
0
0
0
Low
Power
0
1
0
1
Screen Off
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data00 :High channel data
Data01 :Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 :[Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analogue - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 to Max: 7DH
18. Auto Configure(Command: j u)
20. Programme Add/Skip(Command: m b)
►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
►► To set skip status for the current Programme.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
21. Key(Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - See p.23.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
22. Control Back Light(Command: m g)
►► To control the back light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
17. Energy Saving (Command: j q)
29
30
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
23. Input select (Command: x b)
(Main Picture Input)
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
LSB
0
0
0
External Input
0
0
0
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
0
1
1
0
RGB
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
HDMI
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping
00 : Step 0
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
64 :
Step 100
6E : Step 110
73 :
74 :
Step 115
Step 116
CF : Step 199
FE : Step 254
FF : Step 255
0
or
The model and serial numbers of the TV is
located on the back of the TV
Record it below should you ever need
service.
Model
Serial
Download PDF

advertising