LG | 32LT760H | LG 32LT760H Owner’s Manual

OWNER’S MANUAL
LED LCD TV
Please read this manual carefully before operating your set and retain it
for future reference.
LT38**
LT64**
LT66**
LT74**
LT76**
www.lg.com
2
TABLE OF CONTENTS
ENG
ENGLISH
TABLE OF CONTENTS
3
Licenses
24 MAINTENANCE
3
OPEN SOURCE SOFTWARE
NOTICE
24 Cleaning your TV
24 - Screen, frame, cabinet and stand
24 - Power cord
4
Installation Procedure
24 TROUBLESHOOTING
4
ASSEMBLING AND
PREPARING
25 CAUTION FOR USING EZSIGN
2.0
4
6
7
8
9
9
11
12
14
14
Unpacking
Separate purchase
Parts and buttons
Lifting and moving the TV
Setting up the TV
- Attaching the stand
- Mounting on a table
- Mounting on a wall
- Tidying cables
- How to use Dual Lock™
26 SPECIFICATIONS
15 MAKING CONNECTIONS
15
15
16
16
17
17
17
18
18
18
18
19
19
19
20
20
Connection of TV
Antenna connection
HDMI connection
Component connection
DVI to HDMI connection
RGB-PC connection
RS-232C Setup
Network Setup
- Wired Network Connection
Audio connection
- Digital optical audio connection
Speaker output SETUP
Headphone connection
USB connection
CI module connection
Euro Scart connection
21 REMOTE CONTROL
31 IR CODES
32 EXTERNAL CONTROL DEVICE
SETUP
32 RS-232C Setup
32 Type of connector;
D-Sub 9-Pin Male
32 RS-232C Configurations
33 Communication Parameters
33 Command reference list
34 Transmission / Receiving Protocol
WARNING
If you ignore the warning message, you may
yy
be seriously injured or there is a possibility
of accident or death.
CAUTION
If you ignore the caution message, you may
yy
be slightly injured or the product may be
damaged.
NOTE
The note helps you understand and use
yy
the product safely. Please read the note
carefully before using the product.
LICENSES / OPEN SOURCE SOFTWARE NOTICE
3
Supported licenses may differ by model. For more information about licenses, visit www.lg.com.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit
divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered
in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your registration.
“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”
“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.”
Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274
OPEN SOURCE SOFTWARE NOTICE
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this
product, please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of media, shipping and handling) upon email request to
opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.
ENGLISH
ENG
LICENSES
4
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENG
ENGLISH
NOTE
Image shown may differ from your TV.
yy
Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yy
The available menus and options may differ from the input source or product model that you are
yy
using.
New features may be added to this TV in the future.
yy
The TV can be placed in standby mode in order to reduce the power consumption. And the TV should
yy
be turned off if it will not be watched for some time, as this will reduce energy consumption.
The energy consumed during use can be significantly reduced if the level of brightness of the picture
yy
is reduced, and this will reduce the overall running cost.
Installation Procedure
1
2
3
4
Open the package and make sure all the accessories are included.
Attach the stand to the TV set.
Connect an external device to the TV set.
Make sure the network connection is available.
You can use the TV network functions only when the network connection is made. (Only LT74**, LT76**)
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
and item.
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
yy
Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.
yy
Some models have a thin film attached on to the screen and this must not be removed.
yy
NOTE
The items supplied with your product may vary depending on the model.
yy
Product specifications or contents of this manual may be changed without prior notice due to upgrade
yy
of product functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick
yy
and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory
stick does not fit into your TV’s USB port.
B
A
B
A
*A
10 mm
*B
18 mm
ASSEMBLING AND PREPARING
5
ENERGY AV MODE INPUT
TV
SAVING
2
4
5
7
8
9
0
FLASHBK
LIST
3
6
MARK
FAV
VOL
3D
CH
P
A
G
E
MUTE
MENU INFO
Q.MENU
ENTER
BACK
EXIT
L/R SELECT
FREEZE
RATIO
Remote control,
Batteries (AAA)
(See p.21, 22, 23)
EzSign 2.0 Editor CD
(Only
22/26/32/37/42/47LT640E)
or
Owner’s manual
Power Cord Holder
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76 **)
(See p.14)
Stand Screws
4 EA, M4 x 12
2 EA, M4 x 16
(Only 22LT64**, 22LT38**)
(See p.9)
Stand Screws
8 EA, M4 x 12
(Only 26LT64**, 26LT66**,
26LT38**)
(See p.9)
Stand Screws
8 EA, M4 x 14
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**
32/37/42/47LT74**,
32/37/42/47LT76**)
(See p.10)
Desk-mount Screw
1 EA
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76**)
(See p.11)
Wall mount Screws
4 EA, M6 x 51
(Only 47LT****)
DC Adapter
(Only 22/26LT64**,
26LT66**, 22/26LT38**)
(See p.15)
Stand body / Stand base
(Only 22LT64**, 22LT38**)
(See p.9)
Stand body / Stand base
(Only 26LT64**, 26LT66**,
26LT38**)
(See p.9)
Stand body / Stand base
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76**)
(See p.10)
Protection cover
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76**)
(See p.13)
Isolator
(Depending on model)
(See p.6)
Cable Holder
(Depending on model)
(See p.14)
Dual Lock™
(Only LT64**, LT66**,
LT74**, LT76**)
(See p.14)
Power cord
(Depending on model)
ENGLISH
ENG
1
6
ASSEMBLING AND PREPARING
ENG
ENGLISH
Separate purchase
Separate purchase items can be changed or modified for quality improvement without any notification.
Contact your dealer to buy these items.
These devices only work with certain models.
AN-WF100
Wireless Dongle
Compatibility
LT640E
AN-WF100
Wireless Dongle
•
LT640H, LT380H, LT660H,
LT740H, LT760H
NOTE
Antenna Isolator Installation Guide
yy
-- Use this to install TV in a place where there is a voltage difference between TV Set and GND of
antenna signal.
»» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact
might be heated and excessive heat might cause an accident.
-- You can improve the safety when watching TV by efficiently removing power voltage from TV
antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall,
mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
-- Before starting, be sure that the TV antenna is connected.
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
Cable / Antenna
or
Isolator
2. Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains
connection or through other equipment with a connection to protective earthing - and to a cable
distribution system using coaxial cable, may in some circumstances create a fire hazard. Connection
to a cable distribution system has therefore to be provided through a device providing electrical
isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
ASSEMBLING AND PREPARING
7
ENGLISH
ENG
Parts and buttons
(Only 32/37/42/47LT64**,
32/37/42/47LT66**,
32/37/42/47LT38**,
32/37/42/47LT74**,
32/37/42/47LT76**)
Screen
IN 3
(Only 22/26LT64**,
26LT66**,
22/26LT38**)
Remote control sensor
Speakers
Power Indicator
(Can be adjusted using
the Power Indicator in the
OPTION -menu.)
Clock LED
Button
∨∧
Description
Scrolls through the saved programmes.
Adjusts the volume level.
Turns the power on or off.
8
ASSEMBLING AND PREPARING
ENG
ENGLISH
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged
and for safe transportation regardless of its type
and size.
When transporting a large TV, there should
yy
be at least 2 people.
When transporting the TV by hand, hold the
yy
TV as shown in the following illustration.
CAUTION
Avoid touching the screen at all times, as this
yy
may result in damage to the screen.
It is recommended to move the TV in the
yy
box or packing material that the TV originally
came in.
Before moving or lifting the TV, disconnect
yy
the power cord and all cables.
When holding the TV, the screen should face
yy
away from you to avoid damage.
When transporting the TV, do not expose the
yy
TV to jolts or excessive vibration.
When transporting the TV, keep the TV
yy
upright, never turn the TV on its side or tilt
towards the left or right.
Hold the top and bottom of the TV frame
yy
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
ASSEMBLING AND PREPARING
9
ENGLISH
ENG
Setting up the TV
Put your TV on a pedestal stand and mount the TV on a table or wall.
Attaching the stand
(Only 22/26LT64**, 26LT66**, 22/26LT38** )
3
1
M4 x 12
4 EA
(Only 22LT64**, 22LT38** )
Stand Body
M4X20
Front
Stand Base
M4 x 16
2 EA
Top View
2
(Only 26LT64**, 26LT66**, 26LT38**)
M4 x 12
4 EA
10
ASSEMBLING AND PREPARING
ENG
ENGLISH
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
1
3
M4 x 14
4 EA
Stand Body
M4X20
Front
Stand Base
Top View
M4 x 14
2
4 EA
CAUTION
When attaching the stand to the TV
yy
set, place the screen facing down on a
cushioned table or flat surface to protect the
screen from scratches.
Make sure that the screws are fastened
yy
completely. (If they are not fastened securely
enough, the TV may tilt forward after being
installed.)
Do not fasten the screws with too much
force; otherwise they may be worn out and
get loosened.
NOTE
Remove the stand before installing the TV
yy
on a wall mount by performing the stand
attachment in reverse.
ASSEMBLING AND PREPARING
Securing the TV to a table
1 Lift and tilt the TV into its upright position on a
table.
-Leave a 10 cm (minimum) space from the
wall for proper ventilation.
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
Mount the TV on a table, and then insert and
tighten the supplied screw on the rear of the stand.
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
Do not place the TV near or on sources
yy
of heat, as this may result in fire or other
damage.
Attaching the TV to a table
Image shown may differ from your TV.
The TV must be attached to desk so it cannot be
pulled in a forward/backward direction, potentially
causing injury or damaging the pro duct.
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
WARNING
To prevent TV from falling over, the TV
yy
should be securely attached to the floor/
wall per installation instructions. Tipping,
shaking, or rocking the TV may cause injury.
Adjusting the angle of the TV to suit view
Swivel 90 degrees to the left or right and adjust the
angle of the TV to suit your view.
90
90
4-Screws
(not provided as parts of the product)
Stand
CAUTION
When adjusting the angle of the product,
yy
watch out for your fingers.
»» Personal injury may occur if hands or
fingers are pinched. If the product is tilted
too much, it may fall, causing damage or
injury.
Table
Screws: M5 x L (*L: Table depth + 8-10 mm)
ex) Table depth: 15 mm, Screw: M5 x 25
ENGLISH
ENG
Mounting on a table
11
12
ASSEMBLING AND PREPARING
ENG
ENGLISH
Securing the TV to a wall
(This feature is not available for all models.)
Mounting on a wall
Attach an optional wall mount bracket at the rear of
the TV carefully and install the wall mount bracket
on a solid wall perpendicular to the floor. When you
attach the TV to other building materials, please
contact qualified personnel.
LG recommends that wall mounting be performed
by a qualified professional installer.
10 cm
10 cm
10 cm
10 cm
1 Insert and tighten the eye-bolts, or TV brackets
2
3
and bolts on the back of the TV.
-- If there are bolts inserted at the eye-bolts
position, remove the bolts first.
Mount the wall brackets with the bolts to the
wall.
Match the location of the wall bracket and the
eye-bolts on the rear of the TV.
Connect the eye-bolts and wall brackets tightly
with a sturdy rope.
Make sure to keep the rope horizontal with the
flat surface.
CAUTION
Make sure that children do not climb on or
yy
hang on the TV.
NOTE
Use a platform or cabinet that is strong and
yy
large enough to support the TV securely.
Brackets, bolts and ropes are not provided.
yy
You can obtain additional accessories from
your local dealer.
10 cm
ASSEMBLING AND PREPARING
Separate purchase (Wall Mounting Bracket)
Model
22/26LT64**,
22/26LT38**,
26LT66**
VESA
Standard screw
Number of screws
Wall mount
bracket
100 x 100
M4
4
LSW100B(G)
Model
37/42LT64**,
37/42LT66**,
37/42LT38**,
37/42LT74**,
37/42LT76**
VESA
Standard screw
Number of screws
Wall mount
bracket
200 x 200
M6
4
LSW200B(G)
Model
47LT64**,
47LT66**,
47LT38**,
47LT74**,
47LT76**
VESA
400 x 400
Standard screw
M6
Number of screws 4
Wall mount
bracket
LSW420BX
32LT64**,
32LT66**,
32LT38**
32LT74**,
32LT76**
200 x 100
M4
4
CAUTION
Disconnect the power first, and then move
yy
or install the TV. Otherwise electric shock
may occur.
If you install the TV on a ceiling or slanted
yy
wall, it may fall and result in severe injury.
Use an authorized LG wall mount bracket
and contact the local dealer or qualified
personnel.
Do not over tighten the screws as this may
yy
cause damage to the TV and void your
warranty.
Use the screws and wall mount bracket that
yy
meet the VESA standard. Any damages
or injuries by misuse or using an improper
accessory are not covered by the warranty.
On the 47LT**** models, use M6 x 51
yy
screws.
NOTE
LSW220BX
Use the screws that are listed on the VESA
yy
standard screw specifications.
The wall mount kit includes an installation
yy
manual and necessary parts.
The wall mount bracket is not provided. You
yy
can obtain additional accessories from your
local dealer.
The length of screws may differ depending
yy
on the wall mount. Make sure to use the
proper length.
For more information, refer to the manual
yy
supplied with the wall mount.
Not using the DESK-TYPE STAND
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
Image shown may differ from your TV.
When installing the wall mounting bracket,
use the Protection cover.
Insert the Protection cover into the TV until
clicking sound.
A
B
Protection cover
ENGLISH
ENG
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are described in
the following table.
13
14
ASSEMBLING AND PREPARING
ENG
ENGLISH
Tidying cables
How to use Dual Lock™
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
(This feature is not available for all models.)
1 Install the Power Cord Holder and Power Cord.
It will help prevent the power cable from being
removed by accident.
Fix the set-top box to the TV and use it when you
want to.
1 After removing the protection paper from the
Dual Lock, stick it to the TV and the set-top
box as shown.
Power Cord Holder
Dual Lock™
2 Gather and bind the cables with the Cable
Holder.
2 Attach the set-top box to the TV by pressing
the Velcro strips together.
Cable Holder
(Only 22/26LT64**, 26LT66**, 22/26LT38**)
1 Gather and bind the cables with the Cable
Holder.
Cable Holder
CAUTION
Do not move the TV by holding the Cable
yy
Holder and Power Cord Holder, as the
Cable holders may break, and injuries and
damage to the TV may occur.
NOTE
Please make sure no foreign substances
yy
exist on the surface of the product, and
then firmly attach the Dual Lock.
Before attaching the set-top box to the
yy
TV set, let the attached Dual Lock dry for
at least three days.
MAKING CONNECTIONS
This section on MAKING CONNECTIONS mainly
uses diagrams for the 32LT66** models.
Connect various external devices to the TV
and switch input modes to select an external
device. For more information on external device’s
connection, refer to the manual provided with each
device.
Available external devices are: HD receivers,
DVD players, VCRs, audio systems, USB storage
devices, PC, gaming devices, and other external
devices.
NOTE
The external device connection may differ
yy
from the model.
Connect external devices to the TV
yy
regardless of the order of the TV port.
If you record a TV program on a DVD
yy
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
on recording, refer to the manual provided
with the connected device.
Refer to the external equipment’s manual for
yy
operating instructions.
If you connect a gaming device to the TV,
yy
use the cable supplied with the gaming
device.
In PC mode, there may be noise
associated
yy
ANTENNA
IN
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
IN
the PC output to another resolution,
change
the refresh rate to another rate or adjust the
brightness and contrast on the PICTURE
menu until the picture is clear.
In PC mode, some resolution settings may
yy
not work properly depending on the graphics
card.
Connection of TV
(Only 22/26LT64**, 26LT66**, 22/26LT38**)
DC IN
DC Adapter
1 Connect the antenna cable to the antenna
2
3
input port on the TV.
Connect the DC adapter plug to the power
input jack on the TV.
Connect the power cord to the DC adapter first,
then plug the power cord into the wall power
outlet.
Antenna connection
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
ANTENNA
IN
NOTE
Use a signal splitter to use more than 2 TVs.
yy
If the image quality is poor, install a signal
yy
amplifier properly to improve the image
quality.
If the image quality is poor with an antenna
yy
connected, try to realign the antenna in the
correct direction.
An antenna cable and converter are not
yy
supplied.
ENGLISH
ENG
MAKING
CONNECTIONS
15
16
MAKING CONNECTIONS
ENG
ENGLISH
HDMI connection
(Only 32/37/42/47LT76**)
Transmits the digital video and audio signals from
your PC to the TV. Connect the PC and the TV
with the HDMI cable as shown in the following
illustrations. Choose any HDMI input port to
connect. It does not matter which port you use.
3
ARC (Audio Return Channel)
An external audio device that support
yy
SIMPLINK and ARC must be connected
using HDMI/DVI IN 1 (ARC) port.
When connected with a high-speed HDMI
yy
cable, the external audio device that
supports ARC outputs optical SPDIF without
additional optical audio cable and supports
the SIMPLINK function.
Component connection
(Only LT64**, LT66**, LT38**, LT74**)
Transmits the analogue video and audio signals
from an external device to the TV. Connect the
external device and the ‑TV with the component
cable as shown in the following illustrations.
DVD/ Blu-Ray /
HD Cable Box / HD STB
/ PC
1
2
(*Not
Provided)
(*Not Provided)
RED
WHITE
RED
BLUE
GREEN
HDMI
NOTE
It is recommended to use the TV with the
yy
HDMI connection for the best image quality.
Use the latest High Speed HDMI™ Cable
yy
with CEC (Customer Electronics Control)
function.
High Speed HDMI™ Cables are tested to
yy
carry an HD signal up to 1080p and higher.
Supported DTV Audio: MPEG, Dolby Digital,
yy
Dolby Digital Plus, HE-AAC
Supported HDMI Audio format : Dolby
yy
Digital, PCM (Up to 192 KHz, 32k/44.1k/48k
/88k/96k/176k/192k, DTS Not supported.)
VIDEO
AUDIO
DVD/ Blu-Ray / HD
Cable Box
NOTE
If cables are not installed correctly, it could
yy
cause this image to display in black and
white or with distorted colours.
MAKING CONNECTIONS
17
RGB-PC connection
Transmits the digital video signal from an external
device to the TV. Connect the external device and
the TV with the DVI-HDMI cable as shown in the
following illustrations. To transmit an audio signal,
connect an audio cable. Choose any HDMI input
port to connect. It does not matter which port you
use.
Transmits the video signal from PC to the TV. To
transmit an audio signal, connect an audio cable.
AUDIO IN
(RGB/DVI)
RGB IN (PC)
3
(*Not Provided)
AUDIO IN
(RGB/DVI)
1
2
RGB OUT(PC)
AUDIO OUT
PC
RS-232C Setup
(*Not Provided)
AUDIO OUT
AUDIO IN
(RGB/DVI)
DC IN
DVI OUT
AV
(RGB)
RGB IN (PC)
RS-232C IN
(CONTROL & SERVICE)
ANTENNA
IN
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an
A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied
with the product.
RS-232C IN
(CONTROL & SERVICE)
1
2
DVD/ Blu-Ray / HD Cable Box / PC
NOTE
yyDepending on the graphics card, DOS mode
may not work if a HDMI to DVI Cable is in use.
OPTICAL
DIGITA
T L
AUDIO OUT
(*Not Provided)
SPEAKER
OUT
(RGB/DVI)
AUDIO IN
RGB IN (PC)
VOLUME CONTROL
STEREO(8 )
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL & SERV
R ICE)
ANTENNA
IN
1
2
ENGLISH
ENG
DVI to HDMI connection
18
MAKING CONNECTIONS
ENG
ENGLISH
Network Setup
Audio connection
(Only 32/37/42/47LT74**, 32/37/42/47LT76**)
(Only 32/37/42/47LT64**, 32/37/42/47LT66**,
32/37/42/47LT38**, 32/37/42/47LT74**,
32/37/42/47LT76**)
You may use an optional external audio system
instead of the built-in speaker.
Wired Network Connection
This TV can be connected to a local area network
(LAN) via the LAN port. After making the physical
connection, the TV needs to be set up for network
communication.
(Image shown may differ from your TV.)
NOTE
If you use an optional external audio device
yy
instead of the built-in speaker, set the TV
speaker feature to off.
Digital optical audio connection
Transmits the digital audio signal from the TV to an
external device. Connect the external device and
the TV with the optical audio cable as shown in the
following illustrations.
AUX LAN
2
LAN
1
Broadband Modem
Router
OPTICAL
DIGITA
T L
AUDIO OUT
Broadband Service
Broadband Modem
(*Not Provided)
Broadband Service
1 Connect the LAN port of the Modem or Router
to the LAN port on the TV.
2 Connect the LAN port of the PC to the AUX LAN
port on the TV.
CAUTION
yyDo not connect a modular phone cable to the
LAN port.
yySince there are various connection methods,
please follow the specifications of your
telecommunication carrier or internet service
provider.
OPTICAL AUDIO IN
Digital Audio System
NOTE
Do not look into the optical output port.
yy
Looking at the laser beam may damage your
vision.
Audio with ACP (Audio Copy Protection)
yy
function may block digital audio output.
MAKING CONNECTIONS
Connect the external speaker to the Speaker
output(STEREO) jack on the TV.
UP
DOWN
Control port for
Speaker out
USB connection
Connect a USB storage device such as a USB
flash memory, external hard drive, or a USB
memory card reader to the TV.
(Only LT64**, LT66**, LT38**, LT74**)
SPEAKER
OUT
STEREO
USB IN
VOLUME
CONTROL
LL+
(8 )
USB
(*Not Provided)
R+
R-
Cable
Spec.
yyEach Up/ Down pin
is pulled to 3.3V
with CPU GPIO.
yyCPU detects
GND / Up / Down
transition from 3.3V
to GND level for
volume control.
(Only LT76**)
USB IN
Method of Volume control port
(Only LT64**, LT66**, LT38**, LT74**)
Transmits the headphone signal from the TV to
an external device. Connect the external device
and the TV with the headphone as shown in the
following illustrations.
USB IN
Headphone connection
(*Not Provided)
(*Not Provided)
NOTE
(*Not Provided)
NOTE
AUDIO menu items are disabled when
yy
connecting a headphone.
When changing AV MODE with a headphone
yy
connected, the change is applied to video
but not to audio.
Optical Digital Audio Out is not available
yy
when connecting a headphone.
Headphone impedance: 16 Ω
yy
Max audio output of headphone: 9 mW to 15
yy
mW
Headphone jack size: 0.35 cm
yy
yyTo use a USB Hub device, make sure that it is
connected to the USB IN 1 (HUB) port.
yySome USB Hubs may not work. If a USB
device connected using a USB Hub is not
detected, connect it to the USB port on the TV
directly.
ENGLISH
ENG
Speaker output SETUP
19
20
MAKING CONNECTIONS
▼PCMCIA CARD SLOT▼
ENG
ENGLISH
CI module connection
Euro Scart connection
Transmits the video and audio signals from an
external device to the TV set. Connect the external
device and the TV set with the Euro Scart cable
as shown on the following illustration. To display
images by using progressive scan, make sure to
use the Euro Scart cable.
AV
(RGB)
AV
(RGB)
(*Not Provided)
View the encrypted (pay) services in digital TV
mode. This feature is not available in all countries.
NOTE
Check if the CI module is inserted into the
yy
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to the TV and the PCMCIA
card slot.
AUDIO / VIDEO
Current
input model
Output
Type
AV
(TV Out1)
Digital TV
Digital TV
Analogue TV, AV
Analogue TV
Component / RGB
Analogue TV
HDMI
Analogue TV
1 TV Out : Outputs Analogue TV or Digital TV
signals.
NOTE
Any Euro scart cable used must be signal
yy
shielded.
REMOTE CONTROL
21
ENGLISH
ENG
REMOTE CONTROL
The descriptions in this manual are based on the buttons on the remote control.
Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching
the
and
ends to the label inside the compartment, and close the battery cover.
To remove the batteries, perform the installation actions in reverse.
CAUTION
Do not mix old and new batteries, as this may damage the remote control.
yy
Make sure to point the remote control toward the remote control sensor on the TV.
(Only LT64**, LT66**, LT76**)
Number buttons
Enters numbers.
Turns the TV on or off.
ꕊ ENERGY SAVING
Adjusts the brightness of the screen to
reduce energy consumption.
ENERGY
AV MODE
TV/
RAD
AV MODE
Selects an AV mode.
TV/RAD
Selects Radio, TV and DTV programme.
GUIDE
Shows programme guide. (Only LT640H,
LT660H, LT760H)
Shows Contents List in EzSign mode. (Only
LT640E)
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
RATIO
GUIDE PORTAL INFO
FAV
Accesses your favourite programme list.
RATIO
Resizes an image.
MUTE
Mutes all sounds.
EXIT
Home
OK
Selects menus or options and confirms
your input.
1
Q.MENU
AD
P
A
G
E
ꕍPꕌ
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
Colour buttons
These access special functions in some GUIDE
menus.
(
: Red,
: Green,
: Yellow,
: Blue)
1 TELETEXT BUTTONS
These buttons are used for teletext.
OK
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
Q. MENU
Accesses the quick menus.
P
MUTE
INFO
Views the information of the current
programme and screen.(Only LT640H,
LT660H, LT760H)
Shows or hides the information on TV
remote control buttons in EzSign mode.
(Only LT640E)
EXIT
Clears on-screen displays and return to TV
viewing.
Adjusts the volume level.
FAV
PORTAL
Displays and removes hotel interactive
menu.(Only LT640H, LT660H, LT760H)
Displays the EzSign content on a TV
Screen. (Only LT640E)
Returns to the previous level.
Q.VIEW
Returns to the previously viewed programme.
SAVING
INPUT
Changes the input source.
Home
Selects a menu.
Clears all on-screen displays and returns
to TV viewing from any menu.
LIST
Accesses the saved programme list.
INPUT
ALARM
SUBTITLE
Recalls your preferred subtitle in digital
mode.
OK
Home
Control buttons (ꕗ, ꕖ, ꕘ, ꕚ, ꕙ)
Controls the MY MEDIA menus, or
the SIMPLINK compatible devices
(USB,SIMPLINK).(Only LT640H, LT660H,
LT760H)
Not functional when EzSign contents is on.
(Only LT640E)
SIMPLINK
Accesses the AV devices connected with the
HDMI cable through HDMI-CEC.
Opens the SIMPLINK menu.
AD
Switches the Audio Description On or Off.
ALARM
Sets the alarm function.
PORTAL INFO
BACK
EXIT
22
REMOTE CONTROL
ENG
ENGLISH
(Only LT38**)
Number buttons
Enters numbers.
Turns the TV on or off.
ꕊ ENERGY SAVING
Adjusts the brightness of the screen to
reduce energy consumption.
AV MODE
Selects an AV mode.
INPUT
Changes the input source.
TV/RAD
Selects Radio, TV and DTV programme.
GUIDE
Shows programme guide.
ENERGY
AV MODE
TV/
RAD
1
2
3
4
5
6
7
8
9
LIST
0
Q.VIEW
RATIO
GUIDE
ALARM
INFO
OK
FAV
Accesses your favourite programme list.
RATIO
Resizes an image.
MUTE
Mutes all sounds.
P
A
G
E
ꕍPꕌ
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
Colour buttons
GUIDE
These access special functions in some
menus.
(
: Red,
: Green,
: Yellow,
: Blue)
SUBTITLE
Recalls your preferred subtitle in digital
mode.
Home
Control buttons (ꕗ, ꕖ, ꕘ, ꕚ, ꕙ)
Controls the MY MEDIA menus, or
the SIMPLINK compatible devices
(USB,SIMPLINK).
EXIT
1
Clears on-screen displays and return to TV
viewing.
Q.MENU
AD
PORTAL IN
OK
1 TELETEXT BUTTONS
These buttons are used for teletext.
EXIT
Home
Returns to the previous level.
AD
Switches the Audio Description On or Off.
P
MUTE
OK
Selects menus or options and confirms
your input.
Q. MENU
Accesses the quick menus.
Adjusts the volume level.
FAV
INFO
Views the information of the current
programme and screen.
Home
Selects a menu.
Clears all on-screen displays and returns
to TV viewing from any menu.
Q.VIEW
Returns to the previously viewed programme.
SAVING
ALARM
Sets the alarm function.
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
LIST
Accesses the saved programme list.
INPUT
SIMPLINK
Accesses the AV devices connected with the
HDMI cable through HDMI-CEC.
Opens the SIMPLINK menu.
BACK
E
REMOTE CONTROL
23
ENGLISH
ENG
(Only LT74**)
Number buttons
Enters numbers.
Turns the TV on or off.
ꕊ ENERGY SAVING
Adjusts the brightness of the screen to
reduce energy consumption.
ENERGY
AV MODE
LIST
Accesses the saved programme list.
INPUT
AV MODE
Selects an AV mode.
SAVING
1.,;@ 2 abc 3 def
INPUT
Changes the input source.
0
[
LIST
PORTAL
Displays and removes hotel interactive
menu.
CHAR/NUM
Shifts the Character or Number.
Q.VIEW
CHAR/NUM
MARK
RATIO
INFO
Views the information of the current
programme and screen.
P
DELETE
MUTE
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
PORTAL INFO
GUIDE PORTAL
OK
Selects menus or options and confirms
your input.
OK
Home
Selects a menu.
Clears all on-screen displays and returns
to TV viewing from any menu.
Home
P
A
G
E
RATIO
Resizes an image.
MUTE
Mutes all sounds.
DELETE
Deletes the entered character when entering
the character on the screen keyboard.
ꕍPꕌ
Scrolls through the saved programmes.
PAGE
Moves to the previous or next screen.
BACK EXIT
Back
Returns to the previous level.
Colour buttons
These access special functions in some
menus.
(
: Red,
: Green,
: Yellow,
: Blue)
SUBTITLE
Recalls your preferred subtitle in digital mode.
1
AD
Switches the Audio Description On or Off.
SIMPLINK
Accesses the AV devices connected with
the HDMI cable through HDMI-CEC.
Opens the SIMPLINK menu.
MARK
Select the input to apply the Picture Wizard
settings.
Check and un-check programmes in the USB
menu.
7pqrs 8 tuv 9 wxyz
GUIDE
Shows programme guide.
1 TELETEXT BUTTONS
These buttons are used for teletext.
Adjusts the volume level.
4 ghi 5 jkl 6 mno
TV/RAD
Selects Radio, TV and DTV programme.
EXIT
Clears on-screen displays and return to
TV viewing.
Q.VIEW
Returns to the previously viewed programme.
TV/
RAD
Q.MENU
AD
ALARM
Control buttons (ꕗ, ꕖ, ꕘ, ꕚ, ꕙ)
Controls the MY MEDIA menus, or
the SIMPLINK compatible devices
(USB,SIMPLINK).
Q. MENU
Accesses the quick menus.
ALARM
Sets the alarm function.
24
MAINTENANCE / TROUBLESHOOTING
ENG
ENGLISH
MAINTENANCE
Cleaning your TV
Clean your TV regularly to keep the best performance and to extend the product lifespan.
CAUTION
Make sure to turn the power off and disconnect the power cord and all other cables first.
yy
When the TV is left unattended and unused for a long time, disconnect the power cord from the wall
yy
outlet to prevent possible damage from lightning or power surges.
Screen, frame, cabinet and stand
yy To remove dust or light dirt, wipe the surface with a dry, clean, and soft cloth.
yy To remove major dirt, wipe the surface with a soft cloth dampened in clean water or a diluted mild
detergent. Then wipe immediately with a dry cloth.
CAUTION
Avoid touching the screen at all times, as this may result in damage to the screen.
yy
Do not push, rub, or hit the screen surface with your fingernail or a sharp object, as this may result in
yy
scratches and image distortions.
Do not use any chemicals as this may damage the product.
yy
Do not spray liquid onto the surface. If water enters the TV, it may result in fire, electric shock, or
yy
malfunction.
Power cord
Remove the accumulated dust or dirt on the power cord regularly.
TROUBLESHOOTING
Problem
Solution
Cannot control the
TV with the remote
control.
Check the remote control sensor on the product and try again.
yy
Check if there is any obstacle between the product and the remote control.
yy
Check if the batteries are still working and properly installed (
to , to ).
yy
No image display
and no sound is
produced.
Check if the product is turned on.
yy
Check if the power cord is connected to a wall outlet.
yy
Check if there is a problem in the wall outlet by connecting other products.
yy
The TV turns off
suddenly.
Check the power control settings. The power supply may be interrupted.
yy
Check if the Auto sleep feature is activated in the Time settings.
yy
When connecting to
the PC (RGB/HDMI
DVI), ‘No signal’ or
‘Invalid Format’ is
displayed.
Turn the TV off/on using the remote control.
yy
Reconnect the RGB/HDMI cable.
yy
Restart the PC with the TV on.
yy
CAUTION FOR USING EZSIGN 2,0
25
Only 22/26/32/37/42/47LT640E
Do not remove a USB drive while data is being copied. It can corrupt the data and EzSign may not work
yy
properly.
While loading a USB device or dongle, your TV may function slower than normal.
yy
While EzSign contents is running, the movie with internal subtitles is not supported in USB mode. EzSign
yy
TV supports only external subtitles.
(External Subtitle format: *.smi/*.srt/*.sub(MicroDVD, Subviewer 1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/*.
psb(PowerDivX)
Some user-created subtitles may not work properly.
yy
Some special characters are not supported in subtitles.
yy
HTML tags are not supported in subtitles.
yy
Subtitles in languages other than the supported languages are not available.
yy
EzSign 2.0 TV function does not work before completing the initial setup Wizard. Make sure to complete
yy
the initial setup Wizard by turning on the TV after installation.
If the time is set according to the TV signal, it may not appeared exactly for some region. In that case, set
yy
the time manually.
It is recommended that you copy files to the TV memory before playing them, as playing directly from the
yy
USB memory for an extended period of time may cause the device to overheat.
In EzSign 2.0 TV mode, some remote control keys may not work.
yy
EzSign 2.0 TV dose not support the USB HUB. It is recommended that you connect a USB device directly
yy
to the TV without using a USB extension cable as it may not work properly.
It is recommended that you use EzSign 2.0 TV within 8 hours per day as it is standard.
yy
Refer to the EzSign 2.0 Editor user guide for details.
yy
EzSign 2.0 TV does not support Store Demo.
yy
ENGLISH
ENG
CAUTION FOR USING EZSIGN 2.0
26
SPECIFICATIONS
ENG
ENGLISH
SPECIFICATIONS
Product specifications may be changed without prior notice due to upgrade of product functions.
For the power supply and power consumption, refer to the label attached to the product.
MODELS
22LT64**,
22LT38**
22LT640H-ZA
22LT640E-ZA
22LT380H-ZA
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
517.0 x 386.0 x 192.0
517.0 x 386.0 x 192.0
517.0 x 332.0 x 41.6
517.0 x 332.0 x 41.6
3.7
3.7
Weight
With stand(kg)
Without stand(kg)
3.1
3.1
Power requirement
DC 24 V, 1.4 A
AC-DC adaptor : 24 V
, 2.5 A / AC 100-240
V~ 50 / 60 Hz
DC 24 V, 1.4 A
AC-DC adaptor : 24 V
, 2.5 A / AC 100-240
V~ 50 / 60 Hz
Power consumption
40 W
40 W
MODELS
26LT64**
26LT66**
26LT38**
26LT640H-ZA
26LT640E-ZA
26LT660H-ZA
26LT380H-ZA
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
626.0 x 454.0 x 192.0
626.0 x 454.0 x 192.0
626.0 x 454.0 x 192.0
626.0 x 393.0 x 46.6
626.0 x 393.0 x 46.6
626.0 x 393.0 x 46.6
With stand(kg)
4.7
4.7
4.7
Without stand(kg)
4.1
4.1
4.1
Weight
Power requirement
Power consumption
DC 24 V, 1.8 A
DC 24 V, 1.8 A
DC 24 V, 1.8 A
AC-DC adaptor : 24 V
, 2.5 A AC-DC adaptor : 24 V
, 2.5 AC-DC adaptor : 24 V
, 2.5
/ AC 100-240 V~ 50 / 60 Hz
A / AC 100-240 V~ 50 / 60 Hz
A / AC 100-240 V~ 50 / 60 Hz
50 W
50 W
50 W
MODELS
32LT64**
32LT66**
32LT38**
32LT640H-ZA
32LT640E-ZA
32LT660H-ZA
32LT380H-ZA
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
766.0 x 536.0 x 232.0
766.0 x 536.0 x 232.0
766.0 x 536.0 x 232.0
766.0 x 476.0 x 68.5
766.0 x 476.0 x 68.5
766.0 x 476.0 x 68.5
With stand(kg)
9.2
9.2
9.2
Without stand(kg)
8.0
8.0
8.0
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power consumption
60W
60W
60W
32LT74**
32LT76**
32LT740H-ZA
32LT760H-ZA
766.0 x 536.0 x 232.0
766.0 x 536.0 x 232.0
Weight
MODELS
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
766.0 x 476.0 x 68.5
766.0 x 476.0 x 68.5
With stand(kg)
9.2
9.2
Without stand(kg)
8.0
8.0
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power consumption
80W
60W
Weight
SPECIFICATIONS
27
37LT64**
37LT66**
37LT38**
37LT640H-ZA
37LT640E-ZA
37LT660H-ZA
37LT380H-ZA
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
867.0 x 593.0 x 232.0
867.0 x 593.0 x 232.0
867.0 x 593.0 x 232.0
867.0 x 533.0 x 68.6
867.0 x 533.0 x 68.6
867.0 x 533.0 x 68.6
Weight
With stand(kg)
11.2
11.2
11.2
Without stand(kg)
10.0
10.0
10.0
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power consumption
90W
90W
90W
37LT74**
37LT76**
37LT740H-ZA
37LT760H-ZA
867.0 x 593.0 x 232.0
867.0 x 593.0 x 232.0
867.0 x 533.0 x 68.6
867.0 x 533.0 x 68.6
11.2
11.2
MODELS
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
Weight
With stand(kg)
10.0
10.0
Power requirement
Without stand(kg)
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power consumption
100W
90W
42LT64**
42LT66**
42LT38**
42LT640H-ZA
42LT640E-ZA
42LT660H-ZA
42LT380H-ZA
992.0 x 667.0 x 273.0
992.0 x 667.0 x 273.0
992.0 x 667.0 x 273.0
992.0 x 604.0 x 55.0
992.0 x 604.0 x 55.0
992.0 x 604.0 x 55.0
With stand(kg)
15.5
15.5
15.5
Without stand(kg)
13.5
13.5
13.5
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power consumption
100W
100W
100W
42LT74**
42LT76**
42LT740H-ZA
42LT760H-ZA
992.0 x 667.0 x 273.0
992.0 x 667.0 x 273.0
992.0 x 604.0 x 55.0
992.0 x 604.0 x 55.0
With stand(kg)
15.5
15.5
Without stand(kg)
13.5
13.5
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
Power consumption
120W
100W
MODELS
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
Weight
MODELS
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
Weight
ENGLISH
ENG
MODELS
28
SPECIFICATIONS
ENG
ENGLISH
MODELS
47LT64**
47LT66**
47LT38**
47LT640H-ZA
47LT640E-ZA
47LT660H-ZA
47LT380H-ZA
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
1101.0 x 729.0 x 273.0
1101.0 x 729.0 x 273.0
1101.0 x 729.0 x 273.0
1101.0 x 665.0 x 54.5
1101.0 x 665.0 x 54.5
1101.0 x 665.0 x 54.5
With stand(kg)
17.3
17.3
17.3
Without stand(kg)
15.3
15.3
15.3
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50 / 60 Hz
120W
Weight
Power requirement
Power consumption
120W
120W
47LT74**
47LT76**
47LT740H-ZA
47LT760H-ZA
1101.0 x 729.0 x 273.0
1101.0 x 729.0 x 273.0
1101.0 x 665.0 x 54.5
1101.0 x 665.0 x 54.5
With stand(kg)
17.3
17.3
Without stand(kg)
15.3
15.3
Power requirement
AC 100-240 V~ 50 / 60 Hz
AC 100-240 V~ 50/60 Hz
Power consumption
120W
120 W
MODELS
Dimensions With stand(mm)
(W x H x D)
Without stand(mm)
Weight
CI Module Size
(W x H x D)
Environment
condition
100.0 mm x 55.0 mm x 5.0 mm
Operating
Temperature
Operating Humidity
Less than 80 %
Storage Temperature
-20 °C to 60 °C
Storage Humidity
Less than 85 %
Television system
Programme coverage
Maximum
number of
storable
programmes
0 °C to 40 °C
Digital TV
Analogue TV
DVB-T
PAL/SECAM B/G/D/K/I/I',
DVB-C
SECAM L/L’
VHF, UHF
VHF: E2 to E12, UHF: E21 to E69,
CATV: S1 to S20, HYPER: S21 to S47
LT64**, T66**,
LT38**
1,086
LT74**1
500
LT76**
1,200
External antenna impedance
75 Ω
1 In country that Digtal broadcasting regulation isn't fixed, some DTV function may not work depending on
digital broadcasting circumstances. (Only DTV)
SPECIFICATIONS
29
Wireless LAN module(TWFM-B003D) specification
Standard
Frequency Range
Modulation
Output Power
(Typical)
Data rate
Antenna Gain
(Typical)
Occupied bandwidth
IEEE802.11a/b/g/n
2400 to 2483.5 MHz
5150 to 5250 MHz
5725 to 5850 MHz (for Non EU)
CCK / OFDM / MIMO
802.11a: 11 dBm
802.11b: 15 dBm
802.11g: 13 dBm
802.11n - 2.4GHz: 13 dBm
802.11n - 5GHz: 13 dBm
802.11a/g: 54 Mbps
802.11b: 11 Mbps
802.11n: 300 Mbps
2400 to 2483.5 MHz: -2.5dBi
5150 to 5250 MHz: -2.2dBi
5725 to 5850 MHz: -2.9dBi
802.11a/b/g: HT20
802.11n: HT20/40
Because band channel used by the country could be different, the user can not change or adjust the
yy
operating frequency and this product is set for the regional frequency table.
ENGLISH
ENG
Product specifications may be changed without prior notice due to upgrade of product functions.
(Only 32/37/42/47LT76**)
30
SPECIFICATIONS
ENG
ENGLISH
Component port connecting information
HDMI/DVI-DTV supported mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x480
31.469
31.5
59.94
60
720x576
31.25
50
1280x720
37.5
44.96
45
50
59.94
60
33.72
33.75
28.125
26.97
27
33.716
33.75
56.25
67.43
67.5
59.94
60
50
23.97
24
29.976
30.00
50
59.94
60
1920x1080
RGB-PC, HDMI/DVI-PC supported mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
720x400
31.468
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x720
45
60
1280x768
47.78
59.87
1360x768
47.72
59.80
1280x1024
63.981
60.02
1920x1080
(RGB-PC)
66.587
59.93
1920x1080
(HDMI-PC)
67.5
60.00
(Only 37/42/47LT64**, 37/42/47LT66**,
37/42/47LT38**, 37/42/47LT74**,
37/42/47LT76**)
(Only LT64**, LT66**, LT38**, LT74**)
Component ports on the
TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
Signal
Component
480i/576i
O
480p/576p
O
720p/1080i
O
1080p
O
(50 Hz / 60 Hz only)
IR CODES
This feature is not available for all models.
yy
Code
(Hexa)
08
95
30
0B
F0
10-19
53
1A
02
Function
Note
(POWER)
ENERGY SAVING
Remote control Button (Power On/Off)
AV MODE
INPUT
TV/RAD
Number Key 0-9
LIST
Q.VIEW
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
03
Remote control Button
Remote control Button
79
1E
09
00
RATIO
FAV
MUTE (DELETE)
Pꕌ
Remote control Button
Remote control Button
Remote control Button
Remote control Button
01
AB
0C
AA
43
28
Pꕍ
GUIDE
PORTAL
INFO
Home
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
5B
44
40
(BACK)
EXIT
OK
ꕌ
ꕍ
Remote control Button
Remote control Button
Remote control Button
<
Remote control Button
Remote control Button
06
>
Remote control Button
72
71
63
61
RED
GREEN
YELLOW
BLUE
41
07
20
TEXT
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
21
T.OPT(T.Option)
Remote control Button
39
SUBTITLE
ꕗ
Remote control Button
B1
B0
BA
8E

ꕘ
Remote control Button
Remote control Button

Remote control Button
Remote control Button
8F

Remote control Button
7E
45
91
E8
1E
SIMPLINK
Q.MENU
AD
ALARM
MARK (CHAR/NUM)
Remote control Button
Remote control Button
Remote control Button
Remote control Button
Remote control Button
ENGLISH
ENG
IR CODES
31
32
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
EXTERNAL CONTROL DEVICE SETUP
RS-232C Setup
RS-232C Configurations
Connect the RS-232C (serial port) input jack to an
external control device (such as a computer or an
A/V control system) to control the product’s functions externally.
Connect the serial port of the control device to the
RS-232C jack on the product back panel.
Note: RS-232C connection cables are not supplied
with the product.
RS-232C IN
(CONTROL & SERVICE)
7-Wire Configurations (Standard RS-232C cable)
RXD TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations(Not standard)
RXD TXD
GND
DTR
DSR
RTS
CTS
Ty p e o f c o n n e c t o r ;
D-Sub 9-Pin Male
1
5
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Set ID number. "Real Data Mapping".
1 Press Home to access the main menus.
2 Press the Navigation buttons to scroll to
option and press ok.
6
No.
9
Pin name
1
3.5V
2
RXD (Receive data)
3
TXD (Transmit data)
4
IR OUT from TV
5
GND
6
No Connection
7
+5V Power out
8
No Connection
9
+12V Power out
3 Press the Navigation buttons to scroll to set
id and press ok.
4 Scroll left or right to select a set ID number and
select close. The adjustment range is 1-99.
5 When you are finished, press exit.
EXTERNAL CONTROL DEVICE SETUP
33
ENGLISH
ENG
Communication Parameters
Stop bit: 1 bit
yy
Communication code: ASCII code
yy
Use a crossed (reverse) cable.
yy
Baud rate: 9600 bps (UART)
yy
Data length: 8 bits
yy
Parity : None
yy
Command reference list
(Depending on model)
01. Power
k
02. Aspect Ratio k
03. Screen Mute k
a
c
d
DATA
(Hexadecimal)
00 to 01
(See p.35)
(See p.35)
04. Volume Mute k
e
00 to 01
05. Volume
Control
k
f
00 to 64
06. Contrast
k
g
00 to 64
07. Brightness
k
h
00 to 64
08. Colour
k
i
00 to 64
09. Tint
k
j
00 to 64
10. Sharpness
k
k
00 to 64
11. OSD Select
k
l
00 to 01
12. Remote
Control
Lock Mode
k
m
00 to 01
COMMAND1 COMMAND2
k
k
k
DATA
COMMAND2 (Hexadecimal)
r
00 to 64
s
00 to 64
t
00 to 64
x
u
00 to 64
j
q
00 to 05
j
u
01
m
a
(See p.37)
m
b
00 to 01
m
m
c
g
Key Code
00 to 64
x
b
(See p.38)
COMMAND1
13. Treble
14. Bass
15. Balance
16. Colour
Temperature
17. Energy
Saving
18. Auto Configuration
19. Tune
Command
20. Programme
Add/Skip
21. Key
22. Control Back
Light
23. Input select
(Main Picture
Input)
yy
* Note : During USB operations such as DivX or EMF, all commands except Power(ka) and Key(mc) are
not executed and treated as NG.
34
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]
[Command 2]
[Set ID]
: First command to control the TV.(j, k, m or x)
: Second command to control the TV.
: You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment
range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
Set ID is indicated as decimal (1 to 99) on menu and as Hexa decimal (0x0 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data. Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ]
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.
Data00: Illegal Code
EXTERNAL CONTROL DEVICE SETUP
35
04. Volume Mute (Command: k e)
►► To control Power On/Off of the set.
►► To control volume mute on/off.
You can also adjust mute using the MUTE button on remote
control.
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Data 00 : Power Off
01 : Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
►► To show Power On/Off.
Transmission [k][a][ ][Set ID][ ][FF][Cr]
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
* Similarly, if other functions transmit ‘0xFF’ data based on this
format, Acknowledgement data feed back presents status
about each function.
* OK Ack., Error Ack. and other message may display on the
screen when TV is power On.
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on)
Ack [e][ ][Set ID][ ][OK/NG][Data][x]
05. Volume Control (Command: k f)
►► To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
02. Aspect Ratio (Command: k c) (Main Picture
Size)
►► To adjust the screen format. (Main picture format)
You can also adjust the screen format using the Aspect
Ratio in the Q.MENU. or PICTURE menu.
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data 01 : Normal screen (4:3)
02 : Wide screen
(16:9)
04 : Zoom
06 : Original
07 : 14:9
09 : Just Scan
0B : Full Wide
10 to 1F : Cinema Zoom 1 to 16
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen aspect
ratio.
* In DTV/HDMI (1080i 50 Hz / 60 Hz, 720p 50Hz / 60 Hz, 1080p
24 Hz / 30 Hz / 50 Hz / 60 Hz), Component( 720p, 1080i,
1080p 50 Hz / 60 Hz) mode, Just Scan is available.
* Full Wide is supported only for DTV.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
►► To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
►► To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
03. Screen Mute (Command: k d)
►► To select screen mute on/off.
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 :
01 :
10 :
Screen mute off (Picture on)
Video mute off
Screen mute on (Picture off)
Video mute on
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of video mute on only, TV will display On Screen
Display(OSD). But, in case of Screen mute on, TV will not
display OSD.
08. Colour (Command: k i)
►► To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
01. Power (Command: k a)
36
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
09. Tint (Command: k j)
13. Treble (Command: k r)
►► To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
►► To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red : 00 to Green : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
10. Sharpness (Command: k k)
►► To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
14. Bass (Command: k s)
►► To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
11. OSD Select (Command: k l)
►► To select OSD (On Screen Display) on/off when controlling
remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00 : OSD off
15. Balance (Command: k t)
►► To adjust balance.
You can also adjust balance in the AUDIO menu.
01 : OSD on
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [t][ ][Set ID][ ][OK/NG][Data][x]
12. Remote control lock mode (Command: k m)
►► To lock the front panel controls on the monitor and remote
control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : Lock off
01 : Lock on
16. Colour Temperature (Command: x u)
►► To adjust colour temperature. You can also adjust Colour
Temperature in the PICTURE menu.
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
* If you are not using the remote control, use this mode.
When main power is on/off, external control lock is released.
* In the standby mode, if key lock is on, TV will not turn on by
power on key of IR & Local Key.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
* Refer to ‘Real data mapping’. See p.38.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
EXTERNAL CONTROL DEVICE SETUP
19. Tune Command (Command: m a)
►► To reduce the power consumption of the TV. You can also
adjust Energy Saving in PICTURE menu.
►► Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Transmission [j][q][ ][Set ID][ ][Data][Cr]
Power Saving
Function
7
6
5
4
0
0
0
0
0
0
0
0
0
0
0
Level
Description
3
2
1
0
Low
Power
0
0
0
0
Off
0
Low
Power
0
0
0
1
Minimum
0
0
Low
Power
0
0
1
0
Medium
0
0
0
Low
Power
0
0
1
1
Maximum
0
0
0
Low
Power
0
1
0
1
Screen Off
Ack [q][ ][Set ID][ ][OK/NG][Data][x]
Data00 : High channel data
Data01 : Low channel data
ex. No. 47 -> 00 2F (2FH)
No. 394 -> 01 8A (18AH),
DTV No. 0 -> Don’t care
Data02 : [Antena]
0x00 : Analog Main
0x10 : DTV Main
0x20 : Radio
[Cable]
0x80 : Analog Main
0x90 : DTV Main
0xA0 : Radio
Channel data range
Analog - Min: 00 to Max: 63 (0 to 99)
Digital - Min: 00 to Max: 3E7 (0 to 999)
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Data Min: 00 to Max: 7DH
18. Auto Configure(Command: j u)
20. Programme Add/Skip(Command: m b)
►► To set skip status for the current Programme.
►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : Skip
01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
21. Key(Command: m c)
►► To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data Key code - See p.31.
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
22. Control Back Light(Command: m g)
►► To control the back light.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
ENG
17. Energy Saving (Command: j q)
37
38
EXTERNAL CONTROL DEVICE SETUP
ENG
ENGLISH
23. Input select (Command: x b)
(Main Picture Input)
►► To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
LSB
0
0
0
0
0
0
External Input
Input Number
External Input
Data
0
0
0
0
DTV
0
0
0
1
Analogue
0
0
1
0
AV
0
1
0
0
Component
RGB
0
1
1
0
0
1
1
1
1
0
0
0
1
0
0
1
1
0
1
0
Input Number
0
0
0
HDMI
Data
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
* Real data mapping
00 : Step 0
A:
Step 10 (Set ID 10)
F:
10 :
Step 15 (Set ID 15)
Step 16 (Set ID 16)
63 :
64 :
Step 99 (SET ID 99)
Step 100
6E : Step 110
73 :
74 :
Step 115
Step 116
CF : Step 199
FE : Step 254
FF : Step 255
0
He
C
USB IN
USB IN
USB IN
Tra
Co
ext
fla
the
me
ing
me
Da
Da
Da
IN 3
IN 3
Ch
An
Dig
or
H/P
H/P
CN
yy
Vie
mo
yy
USB IN
yy
yy
yy
IN 3
yy
Ch
an
H/P
The model and serial numbers of the TV is
located on the back of the TV
Record it below should you ever need
service.
Model
Serial
N
yy
Download PDF