LG | LS-L1260RL | LG LS-L1260RL Owner’s Manual

Room Air Conditioner
OWNER'S MANUAL
?
Please read
before
?
carefully and thoroughly
operating this unit.
Contact the authorized SVC
man
for
this manual
repair
or
maintenance of this unit.
?
Contact the installer for installation of this unit.
?
The
is not intended for use by young
infirm persons without supervision.
children should be supervised to ensure that
appliance
children
?
Young
they do
or
not
play
with the
appliance.
MODELS: LS-J0960RL
LS-L1260RL
LS-K1860RL
LS-K2460RL
Prior to
installation, this air-conditioning
approval by the utility
which provides electricity (EN 60555-3 Norm).
unit must be submitted for
service
ENGLISHTAOPFRCDU
GRE K
1994.11.24 6:10 PM ˘`2
1.A30052P(¿ )
Safety precautions
Safety Precautions
................................2
Warning
Caution .................................3
To
to the
prevent injury
following
user or
other
people and property damage,
the
instructions must be followed.
Incorrect
operation
damage,
the seriousness is classified
due to
ignoring
of instruction will
harm
cause
by the following
or
indications.
Operating Instructions
Preparation
before
operation
..4
This
symbol
indicates the
possibility
of death
or
serious
possibility
of
or
damage
injury.
Remote Control Features .....5
Operation
Mode Selection ......7
This
symbol indicates
properties only.
Additional features ..............13
the
Installation
Care and Maintenance
injury
to
precautions
Care and Maintenance .......16
Do not
....................18
Operation Tips
?
Troubleshooting tips
?
Before You
Call For Service ...............19
Plug in the power plug
properly.
?
Otherwise, it will
electrical shock
heat
cause
or
install, remove and reinstall the unit by yourself.
Improper installation will cause water leakage, electrical
shock, or fire. Please consult authorized dealer or specialist
for the installation work. Please note fault caused by
improper installation is not covered by warranty.
Unit must be installed in an easily accessible area. Any
additional cost required to hire a special equipment to
service the unit will be the responsibility of the customer.
Do not
operate
or
stop the
unit
by inserting or pulling
out the power plug.
?
fire due to
It will
or
generation.
cause
electrical shock
fire due to heat
Do not damage or use an
unspecified power cord.
?
It will
?
If the
generation.
cause
electrical shock
length
modify power cord
or share the outlet
with other
?
It will
or
cause
Do not
supply
damaged, it
replaced by the
manufacturer or its service agent
or a similarly qualified person in
operate with
wet
hand.
Do not insert
?
It may cause electrical
shock.
?
anything into the
Since the fan rotates at
high
speed, this may cause an
injury or damage the unit.
Do not expose the skin
When an abnormality (smell of burning, etc)
Repair
directly to cool air for long
periods of time.
occurs, stop the air conditioner, and disconnect
the power plug or turn off the breaker.
not be done
health.
hazard.
appliances.
electrical shock
fire due to heat
This could
a
air inlet/air outlet.
generation.
?
fire.
must be
order to avoid
Do not
or
cord is
damage
your
?
If the unit continues to be
in
an
abnormal
cause a
operated
condition, it may
fire, damage,
etc. In this
case, consult your dealer.
or
relocation should
by the
customer.
?
If this is done
incorrectly,
it may
fire, electric shock, injury
by dropping of the unit, water
cause a
leakage,
etc. Consult your dealer.
1994.11.24 6:10 PM ˘`3
1.A30052P(¿ )
CAUTION
?
Contact the authorized Service technician for
?
Contact the installer for installation of this unit.
?
The air conditioner is not intended for
without
?
by young
or
maintenance of this unit.
children
or
infirm persons
supervision.
children should be
Young
use
repair
to
supervised
ensure
that
they
do not
with the air
play
conditioner.
CAUTION
CAUTION
When the air filter is to be
Do not clean the air
removed, do not touch the
metal parts of the indoor unit.
conditioner with water.
?
It may
?
Should be disconnected from
cause an
injury.
?
supply
When the unit is to be
cleaned, switch off,
Since the fan rotates at
high
speed during operation,
may cause an injury.
it
Do not
apply
an
?
a
pet
or
This could
injure
the
house
Do not
insecticide
put
where is
a
or
?
damaged.
The unit may drop or fall
down and cause an injury.
Do not
step
on
the
indoor/outdoor unit and do
to direct
air flow.
?Itmaycauseafireor
may
installation
on
stand which is
stove, etc.
exposed
shortage
Do not leave
?
pet
An oxygen
stove, etc.
a
occur.
plant.
flammable spray.
or
put
?
plant where it will be
exposed to direct air flow.
off the circuit breaker.
?
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
Do not
and turn
Ventilate well when used
together with
not
It may affect combustion.
?
deformation of the cabinet.
put anything
on
it.
It may cause an injury
through dropping or falling
down.
Do not insert hands
vanes
is
?
It will
through
when the air conditioner
When the unit is not
Do not
be used for
bench when
injury by the
?
blower.
Do not
use
for
If not, dirt may collect and
fire.
cause a
special
Do not
operate for a long time in
high humidity, e.g. leaving a
purposes.
door
?
Do not
use
this air conditioner
precision devices,
food, animal, plants, and art
objects.
to preserve
It may
cause
quality,
etc.
going to
long time, turn
deterioration of
?
or
window open.
In the cooling mode, if it is
operated in a room with high
humidity (80%RH or more) for
a long time, water condensed
in the air conditioner may drop
and may wet and spoil
furniture,
etc.
3
step
onto
an
unstable
cleaning and/or
maintaining the unit.
off the circuit breaker.
operationg
cause an
rotating
a
?
It may
cause an
by falling
down.
injury,
etc.
ENGLISH
before
Preparation
SafetyPrcuions
operation
How to Insert the Batteries
Remove the
battery
arrow
direction.
Insert
new
battery
batteries
are
installed
Reattach the
cover
cover
by pulling
making sure
correctly.
by sliding
it
according
that the
it back into
(+)
to the
and
of
(-)
position.
NOTES:
?
Use 2 AAA(1.5volt) batteries. Do not
use
rechargeable
batteries.
OperatingIsuco
CarendMitc
Troubleshtingp
Storage and Tips
For
Using
the Remote Control
The remote control may be stored mounted
wall.
?
?
on a
To
operate the
air
room
remote control at the
?
The remote control will
at
a
conditioner, aim the
signal receptor.
operate the air conditioner
distance of up to 7m.
Signal Receptor
Receives the
signals
from the remote
control.(Signal receiving
sound: two short
beeps
or one
long beep.)
Operation Indication Lamps
On/Off
the
system operation.
:
Lights
up
during
:
Lights
up
during Sleep
Timer
:
Lights
up
during
Defrost Mode
:
Sleep
Mode
Timer
Mode Auto
operation.
operation.
Lights up during Defrost Mode or Hot
operation (Heat pump model only)
Start
OUT
DOOR
OUTDOOR UNIT
:
Lights up during outdoor
(Cooling model only)
:
Indicates the
OPERATION
Power
Display
(Inverter only)
unit
operation.
setting temperature and the
operating frequency of compressor.(5 steps)
4
Signal
receptor
Operation
indication
lamps
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`5
About the remote control
The remote control transmits the
signals
to the
on
the system
system.
Features of the Remote Control- Door Closed
START/STOP BUTTON
Operation starts when this button is
pressed and stops when the button is
pressed again.
1
OPERATION MODE
SELECTION BUTTON
Used to select the operation mode.
2
ROOM TEMPERATURE
SETTING BUTTONS
3
5
6
4
1
Used to select the
3
JET COOL
5
Used to start or stop the speed
cooling. (Speed cooling operates
super high fan speed in cooling mode.)
2
CHAOS SWING BUTTON
6
Used to
stop
or
set the desired
Operation
temperature.
INDOOR FAN SPEED
SELECTOR
Used to select fan speed in four steps
low, medium, high, or CHAOS.
4
Flip-up door
(closed)
room
start louver movement and
up/down
airflow direction.
Mode
Cooling Operation
Cooling Operation
Auto
Auto
Operation
Operation
Healthy Dehumidification Operation
Healthy Dehumidification Operation
Heating Operation
(Cooling Model)
(Heat Pump Model)
5
ENGLISH
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`6
Features of the Remote Control- Door
1
Opened
ON/OFF TIMER BUTTONS
Used to set the time of starting and stopping
operation.
2
TIME SETTING BUTTONS
Used to adjust the time. (See page 13)
3
TIMER SET/CANCEL BUTTONS
Used to set the timer when the desired time is
obtained and to cancel the Timer
operation.
(See page 13)
4
ON
5
OFF
SLEEP MODE AUTO BUTTON
Used to set Sleep Mode Auto operation.
(See page 13)
AIR CIRCULATION BUTTON
Used to circulate the
heating (turns
(See page 14)
or
SET
CANCEL
room
indoor fan
air without
cooling
on/off).
PLASMA
6
ROOM TEMPERATURE
CHECKING BUTTON
Used to check the
7
temperature.
PLASMA(OPTION)
Used to start
function.
8
room
or
stop the plasma-purification
(See page 12)
RESET BUTTON
Used prior to resetting
batteries.
time
or
after
replacing
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`7
How to
use
the
Operation
Mode Selection button
Cooling Operation
1
Press the
a
2
beep.
Open the door on the remote control. To select Cooling
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
on
lower than the
room
a
Healthy
Dehumidification
Close the door
set within
arrow.
Auto
Cooling
3
ENGLISH
Start/Stop button.
respond with
The unit will
Heating
(Heat pump model only)
the remote control. Set the
temperature
temperature. The temperature can be
range of 18°C~30°Cin 1°C increments.
To raise the temperature
To lower the temperature
4
Set the fan
can
For
more
by the
fresh
CHAOS
feeling
CHAOS mode. In this
speed according
with the door
select the fan
speed
in four
steps-
CHAOS. Each
low, medium, high,
or
time the button is
pressed,
speed
Natural wind
speed again
of the remote control still closed. You
the fan
mode is shifted.
logic
than other fan
speed,
press the Indoor Fan
Speed
Selector and set to
mode, the wind blows like natural breeze by automatically changing fan
to the CHAOS
logic.
7
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`8
Auto
SafetyPrcuions
Operation
1
a
OperatingIsuco
CarendMitc
Troubleshtingp
Press the
2
Start/Stop button.
respond with
The unit will
beep.
Open the door on the remote control. To select Auto
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
Cooling
3
The
arrow.
Auto
Healthy
Dehumidification
temperature and fan speed
electronic controls based
on
are
Heating
(Heat pump model only)
automatically
the actual
room
set
by
the
temperature. If
you want to change the set temperature, close the door on
the remote control and press the Room Temperature Setting
buttons. The cooler
two
times)
will then be
or warmer you feel, the more times (up to
you should press the button. The set temperature
changed automatically.
To raise the temperature
To lower the temperature
During Auto Operation:
You cannot switch the indoor fan
speed. It has already been set by the Fuzzy rule.
operating as desired, manually switch to another mode. The system will not
automatically switch from the cooling mode to the heating mode, or from heating to cooling, it must be
done by manually resetting.
During Auto Operation, pressing the chaos swing button makes the horizontal louvers swing up and
down automatically. If you want to stop auto-swing, press the chaos swing button again.
If the
system is
not
8
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`9
Healthy Dehumidification Operation
Press the
1
ENGLISH
Start/Stop button.
respond with
The unit will
a
2
beep.
Open
the door
the remote control. To select
on
Dehumidification
Operation,
press the
Healthy
Operation Mode
Selection button.
Each time the button is
pressed,
shifted in the direction of the
Auto
Cooling
the
operation
Healthy
Dehumidification
3
Set the fan
Heating
(Heat pump model only)
with the door
of the remote control still closed. You
can
select the fan
speed
in four
or
time the button is
pressed,
Natural wind
the fan
mode is shifted.
by the
fresh
CHAOS
logic
speed, press the Indoor Fan
Selector and set to CHAOS mode. In this mode, the wind
more
Speed
steps-
CHAOS. Each
low, medium, high,
speed
For
speed again
mode is
arrow.
feeling
than other fan
blows like natural breeze
according
to the CHAOS
by automatically changing
logic.
fan
speed
During Healthy Dehumidification Operation:
If you select the dehumidification mode on the operation selection button, the A/C starts to run the
dehumidification function, automatically setting the room temp. and airflow volume to the best condition
for dehumidification based
on
the sensed current
In this case, however, the setting
control the room temp. either.
temp. is
not
room
displayed
temp.
in the remote control and you
are
not able to
During the healthy dehumidification function, the airflow volume is automatically set according to the
optimization algorithm responding to the current room temp. status and makes the room condition
healthy and comfortable even in the high humidity season.
9
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`10
Heating Operation(Heat pump model only)
SafetyPrcuions
1
a
2
OperatingIsuco
CarendMitc
Troubleshtingp
Press the
Start/Stop button.
respond with
The unit will
beep.
Open the door on the remote control. To select Heating
Operation, press the Operation Mode Selection button.
Each time the button is pressed, the operation mode is
shifted in the direction of the
arrow.
Auto
Cooling
Healthy
Dehumidification
3
Close the door
on
Heating
(Heat pump model only)
the remote control.
Set the
temperature higher than the room temperature.
The temperature can be set within a range of 16°C~30°Cin
1°C increments.
To raise the temperature
To lower the temperature
4
Set the fan
speed again
with the door of the
remote control still closed. You
the fan
speed
in four
can
select
steps--low, medium,
high, or CHAOS. Each time the button
pressed, the fan speed mode is shifted.
Natural wind
For
more
by the
fresh
CHAOS
feeling
CHAOS mode. In this
speed according
is
logic
than other fan
speed,
press the Indoor Fan
Speed
Selector and set to
mode, the wind blows like natural breeze by automatically changing fan
to the CHAOS
logic.
10
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`11
Jet Cool
Operation
1
Press the
a
2
beep.
Press the Jet Cool button to
the
will
on
3
ENGLISH
Start/Stop button.
respond with
The unit will
speed cooling
operate
mode and the unit
operate in super high fan speed
cooling
mode for 30 minutes.
To cancel the Jet Cool
again or the
setting button
cooling mode.
mode, press the Jet Cool button
button or the room temperature
and the unit will operate in high fan speed on
fan
or
speed
or
NOTE:
During the JET COOL function at any moment, the A/C starts to blow the cool air at
extremely high speed for 30 minutes setting the room temp. automatically to 18°C. It is
especially used to cool the room temp. in the shortest time in a hot summer.
In heat pump mode
or neuro
fuzzy mode however,
In order to return to the normal
either the
or
operation
the JET COOL button
mode from the JET COOL mode, you just press
button, airflow volume selection or temp. setting button
cooling
mode selection
the JET COOL function is not available.
again.
11
1.A30052P(¿ )
SafetyPrcuions
OperatingIsuco
CarendMitc
Troubleshtingp
1994.11.24 6:10 PM ˘`12
PLASMA Purification
1
Operation(Option)
Press the
Start/Stop button.
respond with a
The unit will
beep.
2
3
Open
the door
on
the remote control.
Press the PLASMA air
purifying
operation ON/OFF button.
Operation will start when the button is
pressed and stop when the button is
pressed again.
Set the fan
closed. You
speed again
can
medium, high
button is
or
PLASMA
with door of the remote control
select the fan
speed
in four
steps-low,
CHAOS. Each time the
pressed,
the fan
speed
mode
is shifted.
Air
purifying operation (PLASMA)
Heating or any other operations.
PLASMA Air
with
cooling,
Purifying Operateion only
If you press the only PLASMA
air purifying operates only.
button, PLASMA
Then, fan speed is low. You can select the fan
speed in four steps-low, medium, high or
CHAOS.
Each time the button
PLASMA
speed
12
(
mode is shifed.
)
is
pressed,
the fan
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`13
Additional features
Sleep
1
Press the
Mode
Sleep
To cancel the
Sleep Mode, press the sleep
Mode Auto button several times until the star
Mode Auto button to set the
time you want the unit to turn off
automatically.
(
2
programmed in one-hour
by pressing the Sleep Mode
increments
Auto
Note: The
from the
operation display.
The
the
Sleep
in
period
steps of
Mode Button while
1
hour, press
IN COOLING MODE: The
at air
aiming
sure
the
Sleep
Mode Auto LED
lights
temperature will
automatically rise by 1°C over the next 30
minutes and by 2°C in 1 hour for comfortable
sleeping.
conditioner.
Make
at
low fan
mode is available for 1 to 7 times. To
sleep
alter the time
Mode will be
Sleep
operated
speed (cooling) or medium fan
speed (heat pump only) for quiet sleeping.
button 1 to 7 times.
3
) disappears
The Timer is
up.
Setting the Time
1
Time can be set only when you have pressed
the Reset button. If you have just replaced the
batteries, the Reset button should be pressed
Press the Time
2
Setting
buttons until the
desired time is set.
to reset the time.
Press the
Start/Stop
button.
Press the Timer SET button.
3
SET
Note: Check the indicator
for A.M. and P.M.
Delay Start/Pre-Set Stop
1
2
Make
sure
the time is set
remote control
correctly
the
on
4
display.
ON
Press the ON/OFF Timer
buttons to turn Timer
on or
off.
Press the selected on/off
pressing the Timer SET button while
aiming the remote control at the signal
receptor.
OFF
To cancel the
CANCEL
setting the timer.
Press the Timer Cancel button while
aiming
3
Press the Time
Setting
buttons until the desired
one
remote control at the
(The timer lamp on the
display will go out.)
air conditioner and
the
of the
following
four
types of operation.
with the unit
Delay
signal
receptor.
time is set.
NOTE: Select
SET
setting by
OFF Timer
Delay ON
Timer
Delay OFFand
13
running
ON Timer
Delay ONand
OFF Timer
ENGLISH
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`14
Vertical Airflow Direction Control
The
up/down airflow (Vertical Airflow)
adjusted by using the remote control.
be
can
Note:
If you press the CHAOS swing button, the
horizontal airflow direction is changed
based
the CHAOS
algorithm to
evenly and at the
same time to make the human body feel most
comfortable, as if enjoying a natural breeze.
Always use the remote control to adjust the
up/down airflow direction. Manually moving the
vertical airflow direction louver by hand could
damage the air conditioner.
When the unit is shut off, the up/down airflow
automatically
on
distribute the air in the
room
direction louver will close the air outlet vent of
Press the
Open
button to start the unit.
Start/Stop
the door
Press Chaos
on
the
system.
To
adjust left/right(Horizontal Airflow) direction
Caution : Ensure unit is turned off before adjusting
the horizontal airflow direction control.
the remote control.
Swing
Carefully
button and the louvers will
access
up and down. Press the Chaos Swing
button again to set the vertical louver at the
swing
open vertical louver to allow
to the horizontal airflow direction.
Adjust the left/right
airflow direction
hand.
by
desired airflow direction.
Air Circulation Mode
Circulates the
1
2
Press the
Open
room
Start/Stop
the door
on
air without
cooling
or
button. the unit will
heating.
respond
with
a
beep.
the remote control. Press the Air Circulation button. Close the door
remote control. Now each time that you press the Indoor Fan
shifted from low to CHAOS and back to low again.
Speed Selector,
the fan
on
the
speed
is
Note:
CHAOS Air economizes power consumption and
automatically changed from high to low or vice versa,
prevents overcooling. The fan speed is
on the ambient temperature.
depending
1994.11.24 6:10 PM ˘`15
1.A30052P(¿ )
Slide Switch
Operation
ENGLISH
FORCED OPERATION
Operation procedures when the remote control can't be
used.
Open the front panel upward and move the Slide
Switch to the Forced Operation position.
If you want to stop operation, move the Slide Switch to
the Auto Restart or the Remote Control position.
In case the power comes on again after power failure
on the Forced Operation position, the operating
conditions are automatically set as follows:
During Forced Operation, the initial mode continues.
Cooling
Operating
mode
Indoor FAN
Speed
Heat pump Model
Model
Room Temp. ≥ 24°C
Cooling
Setting Temperature
Healthy
Cooling
High
High
22°C
22°C
21°C ≤ Room Temp.
<
24°C
Dehumidification
Healthy Dehumidification
23°C
Rule
Room
Temp. < 21°C
Heating
High
24°C
Auto restart
In
case
the power
comes on
again
after
a
power
failure, Auto Restarting Operation is the function to
operate procedures automatically to the previous
operating
In
conditions.
the air conditioner does not receive any
from the remote control, it will turn off
case
signal
automatically
after 7 hours.
If you want to
use this operation, Open the front
panel upward and move the slide switch to the
Auto Restart position.
If you do not want to use this operation, move the
Slide Switch to the Remote Control position.
When you are out for a while, put the
Slide Switch on the Remote Control.
Helpful information
Fan
speed and cooling capacity.
cooling capacity indicated in the specification is the
value when the fan speed is set to high, and the capacity will
be lower at low or medium fan speed.
High fan speed is recommended when you wish to cool the
room quickly.
The
High
Speed
1.A30052P(¿ )
1994.11.24 6:10 PM ˘`16
Care and maintenance of the air conditioner
CAUTION: Before
SafetyPrcuions
OperatingIsuco
CarendMitc
turn off the main power to the
performing any maintenance,
Indoor Unit
Never
Grille, Case, and Remote Control
Turn the
off before
system
cleaning.
clean, wipe with a soft, dry cloth. Do
use
bleach
or
?
To
use
any of the
followings:
Water hotter than 40°C
Could
not
deformation and/or
cause
discoloration.
abrasives.
?
Volatile substances
NOTE:
Could
Supply power must be disconnected before
cleaning the indoor unit.
conditioner.
the surfaces of the air
damage
Powder
Gasoline
Air filters
Air outlet vent
(behind front panel)
Vertical louver Horizontal louver
Air inlet vent
1
The air filters behind the
front
grille
2
should be
checked and cleaned
once
more
Lift the front
slightly
AIR FILTERS
access
forward to
panel
remove
Clean the filter with
and
the filter tab
pull
the filter.
a vacuum or
warm, soapy
water.
?
If dirt is
conspicuous, wash with a
detergent in lukewarm water.
water (40°C or more) is used, it
solution of
every 2 weeks or
often if neccessary.
?
If hot
may be deformed.
3
After
washing
with water,
dry
well in the
shade.
4
PLASMA FILTER, DEODORIZER
FILTER(OPTION)
1
The PLASMA filter behind the air filters should be
checked and cleaned
once
every 3 months
or more
2
often if necessary.
3
4
Troubleshtingp
system.
DEODORIZER Filter
5
Re-install the air filter.
After
removing
forward to
Dip
the air
remove
filters, pull slightly
the PLASMA filter.
the PLASMA filter into the water mixed
with neutral
detergent,
for 20~30minutes.
Dry the PLASMA filter in the shade for a day
(Especially, the humidity must be removed
perfectly on this parts).
Note the cuts of electric
discharge
Re-install the PLASMA filter to the
lines.
original
position.
PLASMA Filter
1
Don't touch this PLASMA Filter within 10
seconds after
cause an
opening
the inlet
grille,
it may
electric shock.
2
3
16
After
removing
the air
forward to
remove
in the
sunlight
Dry
filters, pull slightly
the DEODORIZER filter.
for tow hours.
Re-install the DEODORIZER filter to the
original position.
1.A30052P(¿ )
1994.11.24 6:11 PM ˘`17
Replacement
?
Recomended
1
Open
of Purifying
use
period
front
panel
:
Filter(Option)
About 2 years
and
remove
air
2
Remove air
3
Insert
purifying
ENGLISH
filters.
filters.
new
air
purifying
filters.
2
Air filter
4
3
Reinsert air filters and close front
panel.
Air
purifying
filter
Outdoor Unit
The heat
exchanger coils
and
panel vents of the
regularly. If clogged
(Side)
with dirt or soot, the heat exchanger and panel Air intake
vents
vents may be professionally steam cleaned.
outdoor unit should be checked
NOTE:
(Rear)
Piping
Drain Hose
Air outlet
Dirty or clogged coils will reduce the
operating efficiency of the system and
higher operating costs.
vents
cause
(Rear)
(Rear)
Air intake vents
(Side)
Air intake
Piping
vents
Drain Hose
(Side)
Piping
Drain Hose
Air outlet vents
Air outlet
vents
17
1.A30052P(¿ )
SafetyPrcuions
OperatingIsuco
CarendMitc
Troubleshtingp
1994.11.24 6:11 PM ˘`18
When the air conditioner is not going to be used for a long time.
When air conditioner is not
used for
to be
going
When the air conditioner is to be used
long time.
a
Operate the air conditioner on
mode (Refer to page 14) for 2
Air circulation
Clean the air filter and install it in the indoor
to 3 hours.
unit.
(Refer to page
?
This will
dry
16 for
cleaning filters.)
out the internal mechanisms.
Turn off the circuit
the
again.
breaker, and disconnect
plug.
Check that the air inlet and outlet of the
indoor/outdoor unit
CAUTION
are
not blocked.
Turn off the circuit breaker when the air conditioner
is not going to be used for a long time.
Dirt may collect and may
cause a
fire.
Remove the batteries from the remote
control.
Operation Tips
Do not overcool the
room.
Keep
blinds
or
curtains
closed.
This is not
good for the
electricity.
health
and wastes
Keep the
Do not let direct sunshine enter
Adjust the
horizontal airflow direction to
room
when the air
operation.
ensure a
in the
Make
sure
that the doors
are
Avoid
doors and
opening
windows
to
keep
as
much
shut
as
Clean the air filter
regularly.
tight.
the cool air in the
room.
vertical and
uniform
temperature
room.
Ventilate the
room
occasionally.
Blockages
possible
temperature
the
conditioner is in
and windows
room
uniform.
in the air filter
reduce the airflow and lower
cooling
and
dehumidifying
effects. Clean at least
every two weeks.
18
once
Since windows
it is
are
kept closed,
idea to open them
and ventilate the room now and
a
then.
good
1.A30052P(¿ )
1994.11.24 6:11 PM ˘`19
Before you call for service...
Troubleshooting Tips! Save time and money!
?
Check the
following points
contact your dealer
or
before
Case
?
operate.
?
has
a
service.... If the fault
peculiar
?
odor.
persists, please
See page
13
Have you made a mistake in timer operation?
Has the fuse blown or has the circuit breaker
been
room
or
Explanation
The air conditioner does not
The
requesting repairs
service center.
-
tripped?
Check that this is not
the
a
damp
walls, carpet, furniture,
or
smell exuded
by
cloth items in the
-
room.
It
is
seems
that condensation
leaking
?
from the air
Condensation
occurs
when the airflow from
the air conditioner cools the
warm room
air.
-
conditioner.
Air conditioner does not
?
This is the
operate for about
?
Wait about three minutes and
3 minutes
when restarted.
Does not cool
or
protector of the mechanism.
operation
will
-
begin.
heat
?
Is the air filter
dirty?
See air filter
cleaning
16
instructions.
effectively.
?
Has the
?
Are the indoor unit's air inlet
temperature been
set
incorrectly?
or
7, 10
outlet vents
obstructed?
The air conditioner
operation
is
?
For
a
-
noise that sounds like water
-This is the sound of freon
noisy.
flowing
flowing.
inside the
air conditioner unit.
?
For
noise that sounds like the
compressed
atmosphere.
-This is the sound of the dehumidifying water
being processed inside the air conditioning
air
a
releasing
into
-
unit.
Remote control
?
Are the batteries
faint,
?
Are the batteries inserted in the
or no
display is
display at all.
and
Crack sound is heard.
?
(-)
depleted?
opposite (+)
4
directions?
This sound is
generated by the
expansion/constriction of the front panel,
due to changes of temperature.
etc.
-
NOTE
WATER RESISTANT: The outdoor side of this
appliance
is WATER RESISTANT.
The indoor side is not water resistant and should not be
19
exposed
to
excess
water.
ENGLISH
Download PDF

advertising